india - bharat petroleum · _____india ... instrumentation works for isom project at ... krishi...

Material/Services required at:M/s. BHARAT PETROLEUM CORPN. LTDMUMBAI REFINERYMAHUL,MUMBAI - 400074India_______________________________________________________________________SUBJECT: INSTRUMENTATION WORKS FOR ISOM PROJECT AT BPCL, MUMBAI REFINERY.

You are invited to quote online through BPCL E-Procurement websitehttps://bpcleproc.in on "Two-Bid-Basis" for the subject work as per theenclosed Tender Documents.

Your quoted rates shall be inclusive of all applicable taxes and duties exceptMaharashtra VAT, Service Tax, Swachh Bharat Cess (SBC) and Krishi Kalyan Cess(KKC), which shall be quoted separately in attached Form-A. Please note thatsubmission of this FORM-A along with Technical / Unpriced Bid is mandatory.Your rates shall remain firm till completion of work. The applicability ofService Tax, Swachh Bharat Cess, Krishi Kalyan Cess and MVAT as a percentagerate of total quoted price shall be clearly mentioned in the Form-A. If theinformation is not provided, it will be assumed that Service Tax, SwachhBharat Cess, Krishi Kalyan Cess and MVAT is not applicable. No claim for theService Tax, Swachh Bharat Cess, Krishi Kalyan Cess and MVAT will beentertained subsequently.

Service Tax, Swachh Bharat Cess, Krishi Kalyan cess and MVAT shall be paidafter verifiying Service tax registration number and MVAT TIN number ininvoice. Break up of basic cost, Service tax, SBC, KKC, MVAT shall be providedin all your invoices along with service tax registration number, MVAT TINnumber, category of Taxable service (service tax category), type of companyand address/ source of supply of material.

Any statutory variation in Service Tax, Swachh Bharat Cess, Krishi Kalyan Cessand MVAT within the contractual completion period shall be to BPCL account,against submission of documentary evidence for substantiating the variation byway of relevant notification. However in case of delay in completion periodbeyond the contractual date, for reasons attributable to contractor, anyincrease in these rates shall be borne by the contractor, whereas any decreasein rates shall be passed on to the owner.

VALIDITY : Your quotation shall be valid for period of 120 Days from theQuotation due date/ extended due date whichaver is later.

To,M/s. BPCL ESTIMATEMUMBAI . India - 400038.Ph:,Fax:.Vendor Code:300648

Quotation Due Date/Time:05.09.2016/12:00:00

For Bharat Petroleum Corporation Ltd.Vendor Sign & Stamp

REQUEST FOR QUOTATION Collective RFQ Number/ Purchase Group 1000263787 / N44-ISOM SER PROC Contact person/Telephone SINARE ANUP/-3269 Fax : - Email:[email protected] Our ref.:

RFQ No/Date: 6000969611 / 29.08.2016

of 63

Submission of tenders on line:

Bidders are requested to submit / upload their UNPRICED & PRICED BIDS alongwith all required documents, on or before the due date by 12.00 hrs., on BPCLE-Procurement website https://bpcleproc.in maintained by M/s. E-procurementTechnologies Ltd. For submitting the digitally signed copy of the unpricedtender documents as token of acceptance, bidders are required to put tick markagainst tender documents in the "Bid common forms" of the E-Tender. In casenothing is mentioned regarding acceptance of the documents in separateattachment titled 'DEVIATIONS', it will be assumed that all tender documentsare acceptable to the bidders. In case of any discrepency between SOR detailsin RFQ document and SOR document of E-tender, the details in RFQ documentshall supersede.

For any assistance regarding online submission of bids on BPCL E-Procurementweb site, you may contact ON +91-22-65354113, 65595111, on all working days(Mon - Fri) between 0900 hrs to 1700 hrs.

Hard copies of the bids shall not be submitted, unless specially asked for byBPCL and the same if submitted shall not be considered for evaluation. ThePRICED BID shall be submitted online as per the pricing format given.

DEVIATION :

You are requested to have all your queries clarified before bidding. However,if you still have deviations from our RFQ and the attachments (specifications/ scope of work / Drawings ) etc. please indicate deviations in your offerunder a separate attachment titled 'DEVIATIONS' giving reference to RFQ clauseno. Deviations appearing in separate attachment of the E-Tender titled'DEVIATIONS' shall only be considered while evaluating the offer. In casethere are no deviations, please submit "NIL DEVIATIONS". Deviations mentionedelsewhere shall not be considered for evaluation.

NEFT PAYMENT:

Payments to contractors etc. shall be made by National Electronic FundTransfer (NEFT) only. Payment by cheque will be made only to those vendorswhose bank is located in the city where NEFT payment facility is presently notavailable. Bids received from vendors who are not accepting the NEFT paymentterms are likely to be rejected.

Clause regarding EMD

The EMD should be submitted on or before the the tender due date/time in aseparate envelop subscribing "EMD" for tender no. CRFQ1000263787 dated29.08.2016 due on 05.09.2016, 12:00 Hrs to Mr. Anup Sinare (Assistant ManagerProject P&CS), 2nd Floor, P&CS Department, Annex Building, BPCL MumbaiRefinery, Mahul-400074.

To:M/s. BPCL ESTIMATE MUMBAI - 400038 India (300648)

For Bharat Petroleum Corporation Ltd.Vendor Sign & Stamp of 63

- Value of EMD shall be Rs. 1,00,000/- (Rs. One Lakh only)

- EMD can be in the form of Demand Draft drawn in favour of Bharat PetroleumCorporation Ltd. or it can be a Bank Guarantee from any Scheduled Bankapproved by Reserve Bank of India. The Bank Guarantee should be valid for sixmonths from the due date of the tender(Bank Guarantee format for EMD enclosedin GCC).

-Copy of DD or BG for EMD shall be uploaded in the E-tender site under clausefor 'EMD'.

- No interest will be paid on EMD.

- If contractor commits any breach of terms and conditions of tender, EMD willbe forfeited.

- However, this clause is not applicable to the contractors meeting thefollowing conditions

1. Registered with Bharat Petroleum Corporation Limited.2. Registered with National Small Scale Industrial Corporation Ltd. (NSIC)subject to conditions.3. MSME enterprises registered with statuatory authorities as per GovernmentRules.

Units registered with National Small Industries Corporation (NSIC) and/orMicro or small Enterprises (MSE) are however, exempted from payment of EMDsubject to:1. The unit being registered for the item tendered2. Registration certificate being valid as on date of quotation

MSME CLAUSE:

Owner reserves its right to allow Public Sector Enterprises (Central/ State),purchase preference as admissible/ applicable from time to time under theexisting Government policy. Purchase preference to a PSE shall be decidedbased on the price quoted by PSE as compared to L1 Vendor at the time ofevaluation of the price bid.

Clause regarding purchase preference to Micro and Small Enterprises

Owner reserves its right to allow Micro and Small Enterprises (MSEs) and MSEsowned by Scheduled Caste (SC) or the Scheduled tribe (ST) entrepreneurs,purchase preference as admissible/ applicable from time to time under theexisting Government policy. Purchase preference to a MSE and a MSE owned bySC/ ST entrepreneurs shall be decided based on the Net Evaluated Price quotedby the said MSEs as compared to L1 Vendor at the time of evaluation of theprice bid, in case the contract is divisible. Bidders claiming purchasepreference as MSE need to submit the following documents:a. Notarized copy of all the pages of the EM-II certificate issued by the



appropriate authorities mentioned in the Public procurement policy ofMSEs-2012.b. Vendors' declaration on a duly notarized Rs.100 stamp paper stating that,in the event of award of contract, all the ordered supplies shall be made fromthe unit for which MSE certificate has been submitted.

The photocopy of the Valid MSE registration with any notified body specifiedby ministry of micro, small and medium enterprises should accompany the biddocuments. Failing which no price preference will be considered in such cases.

The Net Evaluated Price is the all inclusive delivered price.Net Evaluated Price = Quoted Basic Price + Excise duty + Freight +local taxesand duties+ Octroi Charges and /or entry tax less Cenvat Benefits on Exciseand Input Tax Credit on VAT.

Clause regarding ISO Certification and adherence:

BPCL Mumbai Refinery is an ISO:50001:2011 certified Refinery and is focused onenergy efficiency. In line with the same, all contractors providing servicesfor BPCL Mumbai Refinery should preferably deploy energy efficient equipmentssuch as energy efficient welding machines, LED / CFL temporary lighting andtemporary window AC of BEE 4-star rating and above for execution of the work.

Please submit folowing details in the E-Tender attachment titled "reply ofpoint no.13 of special safety conditions" along with techno-commercial bid:-

a) Complete work injury records per year for the last three years.b) Total man-hours worked per year for the last three years.c) Safety assurance plan.d) No. of supervisorse) No. of skilled workmenf) No. of unskilled workmen

In case, reply to Point No.13 is not submitted, bids are likely to berejected/ bids may not be considered for technical evaluation.

In case of any clarification, please contact BPCL Project Manager, Mr. RailkarS. H., Sr. Manager Projects on Tel- 022-25524158 Extn: 4158.---------------------------------------------------------------The details of IEM (Independent External Monitor) as mentioned in section 8 ofour Integrity pact attached:

Name of IEM: Shri. Brahm DuttAddress: A-1/8 Safdarjung Enclave, New Delhi-110 029.Mobile: 09871920282.E-Mail: [email protected]

The details of Purchasing / Procuring Officer:



Name of procuring officer: Mr. Anup Sinareoffice address : P&CS Department, Admin Building, BPCL, Mahul Refinery, Mumbai-400074.Contact Details : Ext. 022-25523269, Mo. 9619327662.______________________________________________________________________________________________________________________________________________

Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________

00010 Instrumentation works in NHT/ISOM 05.11.2016_______________________________________________________________________ The item 00010 covers the following services:_______________________________________________________________________ 10 35 NO

Inst. of PG : CS Std. 7-52-0432 (Number) _________________________________________________________________

INSTALLATION OF PRESSURE GAUGE"Installation of Line mounted or Remote mounted or Local Gauge Board mountedPressure gauge/ Pressure gauge with Pulsation Dampener/ Syphon/ OverrangeProtector (direct/ surface mounted/ diaphragm seal type) inclusive of mountingof instrument, supply and erection of supports, mounting on support, (ifsupport required) , laying of capillary on supports, fabrication andinstallation of manifolds/ impulse lines with supports as per standardsindicated below, hydraulic testing and painting of supports but exclusive ofSupply of Instrument, Gauge Board, Yoke, Piping material and Calibration."I010.10.11 : In CS as per Std. 7-52-0432Payment terms:93% after completion of erection/Installation and testing.2% after mechanical completion.5% after completion of all works in all respect and issuance of completioncertificate. _________________________________________________________________INSTALLATION OF PRESSURE GAUGE"Installation of Line mounted or Remote mounted or Local Gauge Board mountedPressure gauge/ Pressure gauge with Pulsation Dampener/ Syphon/ OverrangeProtector (direct/ surface mounted/ diaphragm seal type) inclusive of mountingof instrument, supply and erection of supports, mounting on support, (ifsupport required) , laying of capillary on supports, fabrication andinstallation of manifolds/ impulse lines with supports as per standardsindicated below, hydraulic testing and painting of supports but exclusive ofSupply of Instrument, Gauge Board, Yoke, Piping material and Calibration."I010.10.11 : In CS as per Std. 7-52-0432Payment terms:93% after completion of erection/Installation and testing.2% after mechanical completion.5% after completion of all works in all respect and issuance of completioncertificate. _________________________________________________________________

Service Item 10: Unit basic rate in words ________________________________

_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 20 15 NO



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________Inst. of PG: CS Std A620-000-16-51-IS10 (Number)

_________________________________________________________________INSTALLATION OF PRESSURE GAUGE"Installation of Line mounted or Remote mounted or Local Gauge Board mountedPressure gauge/ Pressure gauge with Pulsation Dampener/ Syphon/ OverrangeProtector (direct/ surface mounted/ diaphragm seal type) inclusive of mountingof instrument, supply and erection of supports, mounting on support, (ifsupport required) , laying of capillary on supports, fabrication andinstallation of manifolds/ impulse lines with supports as per standardsindicated below, hydraulic testing and painting of supports but exclusive ofSupply of Instrument, Gauge Board, Yoke, Piping material and Calibration."I010.10.11M01: In Carbon Steel as per A620-000-16-51-IS10Payment terms:93% after completion of erection/Installation and testing.2% after mechanical completion.5% after completion of all works in all respect and issuance of completioncertificate. _________________________________________________________________INSTALLATION OF PRESSURE GAUGE"Installation of Line mounted or Remote mounted or Local Gauge Board mountedPressure gauge/ Pressure gauge with Pulsation Dampener/ Syphon/ OverrangeProtector (direct/ surface mounted/ diaphragm seal type) inclusive of mountingof instrument, supply and erection of supports, mounting on support, (ifsupport required) , laying of capillary on supports, fabrication andinstallation of manifolds/ impulse lines with supports as per standardsindicated below, hydraulic testing and painting of supports but exclusive ofSupply of Instrument, Gauge Board, Yoke, Piping material and Calibration."I010.10.11M01: In Carbon Steel as per A620-000-16-51-IS10Payment terms:93% after completion of erection/Installation and testing.2% after mechanical completion.5% after completion of all works in all respect and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 30 40 NO

Inst. of PT: CS Std A620-000-16-51-IS15 (Number) _________________________________________________________________

INSTLLATION OF PRESSURE INSTRUMENTInstallation of Pressure Transmitters/ Pressure Switches (with or withoutPulsation Dampener, Overrange Protector)/ Diaphragm seal type PressureTransmitters/ Diaphragm seal type Pressure Switches including mounting onYoke/ Surface, supply of supports for capillary, supply and erection of



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________supports for impulse lines wherever required, fabrication and installation ofmanifolds/ impulse lines with supports as per Standard indicated below, layingof capillary on supports, hydraulic testing and painting of supports butexclusive of Supply of Instrument, Piping materials, all Electrical/ Pneumaticconnections, Yoke and Calibration. _I030.10.11M04 In Carbon Steel as per Standard A620-000-16-51-IS15Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________INSTLLATION OF PRESSURE INSTRUMENTInstallation of Pressure Transmitters/ Pressure Switches (with or withoutPulsation Dampener, Overrange Protector)/ Diaphragm seal type PressureTransmitters/ Diaphragm seal type Pressure Switches including mounting onYoke/ Surface, supply of supports for capillary, supply and erection ofsupports for impulse lines wherever required, fabrication and installation ofmanifolds/ impulse lines with supports as per Standard indicated below, layingof capillary on supports, hydraulic testing and painting of supports butexclusive of Supply of Instrument, Piping materials, all Electrical/ Pneumaticconnections, Yoke and Calibration. _I030.10.11M04 In Carbon Steel as per Standard A620-000-16-51-IS15Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 40 10 NO

Inst. of PT: CS Std A620-000-16-51-IS17 (Number) _________________________________________________________________

INSTLLATION OF PRESSURE INSTRUMENTInstallation of Pressure Transmitters/ Pressure Switches (with or withoutPulsation Dampener, Overrange Protector)/ Diaphragm seal type PressureTransmitters/ Diaphragm seal type Pressure Switches including mounting onYoke/ Surface, supply of supports for capillary, supply and erection ofsupports for impulse lines wherever required, fabrication and installation ofmanifolds/ impulse lines with supports as per Standard indicated below, layingof capillary on supports, hydraulic testing and painting of supports butexclusive of Supply of Instrument, Piping materials, all Electrical/ Pneumatic



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________connections, Yoke and Calibration. _I030.10.11M06 In Carbon Steel as per Standard A620-000-16-51-IS17Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________INSTLLATION OF PRESSURE INSTRUMENTInstallation of Pressure Transmitters/ Pressure Switches (with or withoutPulsation Dampener, Overrange Protector)/ Diaphragm seal type PressureTransmitters/ Diaphragm seal type Pressure Switches including mounting onYoke/ Surface, supply of supports for capillary, supply and erection ofsupports for impulse lines wherever required, fabrication and installation ofmanifolds/ impulse lines with supports as per Standard indicated below, layingof capillary on supports, hydraulic testing and painting of supports butexclusive of Supply of Instrument, Piping materials, all Electrical/ Pneumaticconnections, Yoke and Calibration. _I030.10.11M06 In Carbon Steel as per Standard A620-000-16-51-IS17Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 50 20 NO

Inst. of DPT: CS Std A620-000-16-51-IS27 (Number) _________________________________________________________________

INSTALLATION OF DIFFERENTIAL PRESSURE INSTRUMENTInstallation of Differential Pressure Transmitters (including one sidecapillary type)/ Differential Pressure Switch(including one side capillarytype)/ Diaphragm seal type DP Transmitters/ Diaphragm seal type DP Switchincluding mounting on Yoke/ Surface, supply and erection of supports forimpulse lines wherever required, fabrication and installation of manifolds/impulse lines with supports as per Standard indicated below, supply andfabricating of supports for capillary, laying of capillary on supports,painting, installation of flushing connection, hydraulic testing of impulselines as per standard indicated below but exclusive of Supply of Instrument,Piping material, all Electrical/ Pneumatic connections, Yoke and Calibration.I040.10.11M02 In Carbon Steel as per Standard A620-000-16-51-IS27Payment terms shall be as follows



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _

_________________________________________________________________INSTALLATION OF DIFFERENTIAL PRESSURE INSTRUMENTInstallation of Differential Pressure Transmitters (including one sidecapillary type)/ Differential Pressure Switch(including one side capillarytype)/ Diaphragm seal type DP Transmitters/ Diaphragm seal type DP Switchincluding mounting on Yoke/ Surface, supply and erection of supports forimpulse lines wherever required, fabrication and installation of manifolds/impulse lines with supports as per Standard indicated below, supply andfabricating of supports for capillary, laying of capillary on supports,painting, installation of flushing connection, hydraulic testing of impulselines as per standard indicated below but exclusive of Supply of Instrument,Piping material, all Electrical/ Pneumatic connections, Yoke and Calibration.I040.10.11M02 In Carbon Steel as per Standard A620-000-16-51-IS27Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 60 3 NO

Inst. of DPT: CS Std A620-000-16-51-IS28 (Number) _________________________________________________________________

INSTALLATION OF DIFFERENTIAL PRESSURE INSTRUMENTInstallation of Differential Pressure Transmitters (including one sidecapillary type)/ Differential Pressure Switch(including one side capillarytype)/ Diaphragm seal type DP Transmitters/ Diaphragm seal type DP Switchincluding mounting on Yoke/ Surface, supply and erection of supports forimpulse lines wherever required, fabrication and installation of manifolds/impulse lines with supports as per Standard indicated below, supply andfabricating of supports for capillary, laying of capillary on supports,painting, installation of flushing connection, hydraulic testing of impulselines as per standard indicated below but exclusive of Supply of Instrument,Piping material, all Electrical/ Pneumatic connections, Yoke and Calibration.I040.10.11M03 In Carbon Steel as per Standard A620-000-16-51-IS28Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________INSTALLATION OF DIFFERENTIAL PRESSURE INSTRUMENTInstallation of Differential Pressure Transmitters (including one sidecapillary type)/ Differential Pressure Switch(including one side capillarytype)/ Diaphragm seal type DP Transmitters/ Diaphragm seal type DP Switchincluding mounting on Yoke/ Surface, supply and erection of supports forimpulse lines wherever required, fabrication and installation of manifolds/impulse lines with supports as per Standard indicated below, supply andfabricating of supports for capillary, laying of capillary on supports,painting, installation of flushing connection, hydraulic testing of impulselines as per standard indicated below but exclusive of Supply of Instrument,Piping material, all Electrical/ Pneumatic connections, Yoke and Calibration.I040.10.11M03 In Carbon Steel as per Standard A620-000-16-51-IS28Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 70 6 NO

Inst. Draft gauge: A620-000-16-51-IS22 (Number) _________________________________________________________________

INSTALLATION OF DRAFT GAUGE Installation of Differential pressure(with orwithout integral manifold)/ Diaphragm Seal Type Differential Pressure flowinstruments including Mounting on Yoke, supply of supports for impulse lines/manifolds/ capillary, fabrication and Installation of manifolds/ impulse lineswith supports as per Standard indicated below, laying of capillary onsupports, hydraulic testing and painting of supports but exclusive of Supplyof Instruments, Piping material, all Electrical/ Pneumatic connections, Yokeand Calibration. _I050.10.01M01 In Carbon Steel as per Standard A620-000-16-51-IS22

_________________________________________________________________INSTALLATION OF DRAFT GAUGE Installation of Differential pressure(with orwithout integral manifold)/ Diaphragm Seal Type Differential Pressure flowinstruments including Mounting on Yoke, supply of supports for impulse lines/manifolds/ capillary, fabrication and Installation of manifolds/ impulse lineswith supports as per Standard indicated below, laying of capillary onsupports, hydraulic testing and painting of supports but exclusive of Supplyof Instruments, Piping material, all Electrical/ Pneumatic connections, Yokeand Calibration. _



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________I050.10.01M01 In Carbon Steel as per Standard A620-000-16-51-IS22

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 80 35 NO

Inst. of FT: CS Std A620-000-16-51-IS07 (Number) _________________________________________________________________

DIFFERENTIAL PRESSURE (FLOW) TRANSMITTERS Installation of Differentialpressure(with or without integral manifold)/ Diaphragm Seal Type DifferentialPressure flow instruments including Mounting on Yoke, supply of supports forimpulse lines/ manifolds/ capillary, fabrication and Installation ofmanifolds/ impulse lines with supports as per Standard indicated below, layingof capillary on supports, hydraulic testing and painting of supports butexclusive of Supply of Instruments, Piping material, all Electrical/ Pneumaticconnections, Yoke and Calibration. _I090.10.11M07 In Carbon Steel as per Standard A620-000-16-51-IS07Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________DIFFERENTIAL PRESSURE (FLOW) TRANSMITTERS Installation of Differentialpressure(with or without integral manifold)/ Diaphragm Seal Type DifferentialPressure flow instruments including Mounting on Yoke, supply of supports forimpulse lines/ manifolds/ capillary, fabrication and Installation ofmanifolds/ impulse lines with supports as per Standard indicated below, layingof capillary on supports, hydraulic testing and painting of supports butexclusive of Supply of Instruments, Piping material, all Electrical/ Pneumaticconnections, Yoke and Calibration. _I090.10.11M07 In Carbon Steel as per Standard A620-000-16-51-IS07Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 90 10 NO

Inst. of FT : CS Std A620-000-16-51-IS06 (Number)




_________________________________________________________________DIFFERENTIAL PRESSURE (FLOW) TRANSMITTERS Installation of Differentialpressure(with or without integral manifold)/ Diaphragm Seal Type DifferentialPressure flow instruments including Mounting on Yoke, supply of supports forimpulse lines/ manifolds/ capillary, fabrication and Installation ofmanifolds/ impulse lines with supports as per Standard indicated below, layingof capillary on supports, hydraulic testing and painting of supports butexclusive of Supply of Instruments, Piping material, all Electrical/ Pneumaticconnections, Yoke and Calibration. _I090.10.11M06 In Carbon Steel as per Standard A620-000-16-51-IS06Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________DIFFERENTIAL PRESSURE (FLOW) TRANSMITTERS Installation of Differentialpressure(with or without integral manifold)/ Diaphragm Seal Type DifferentialPressure flow instruments including Mounting on Yoke, supply of supports forimpulse lines/ manifolds/ capillary, fabrication and Installation ofmanifolds/ impulse lines with supports as per Standard indicated below, layingof capillary on supports, hydraulic testing and painting of supports butexclusive of Supply of Instruments, Piping material, all Electrical/ Pneumaticconnections, Yoke and Calibration. _I090.10.11M06 In Carbon Steel as per Standard A620-000-16-51-IS06Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 100 10 NO

Inst. of LT:CS Std A620-000-16-51-IS24 (Number) _________________________________________________________________

DIFFERENTIAL PRESSURE (LEVEL) TRANSMITTERS Installation of DP type/ DiaphragmSeal DP type Level Instrument including mounting on Yoke, supply of supportsfor impulse line/ capillary/ manifold, fabrication of manifolds and erectionwherever required, laying of capillary on supports, fabrication andinstallation of impulse lines with support as per Standard indicated below,hydraulic testing and painting of supports but exclusive of Supply ofInstrument, Piping material, all Electrical/ Pneumatic connections, Yoke andCalibration. Impulse lines made of Piping. _



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________I150.10.11M01 In Carbon Steel as per Standard A620-000-16-51-IS24Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________DIFFERENTIAL PRESSURE (LEVEL) TRANSMITTERS Installation of DP type/ DiaphragmSeal DP type Level Instrument including mounting on Yoke, supply of supportsfor impulse line/ capillary/ manifold, fabrication of manifolds and erectionwherever required, laying of capillary on supports, fabrication andinstallation of impulse lines with support as per Standard indicated below,hydraulic testing and painting of supports but exclusive of Supply ofInstrument, Piping material, all Electrical/ Pneumatic connections, Yoke andCalibration. Impulse lines made of Piping. _I150.10.11M01 In Carbon Steel as per Standard A620-000-16-51-IS24Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 110 10 NO

Inst. of LT:CS Std A620-000-16-51-IS25 (Number) _________________________________________________________________

DIFFERENTIAL PRESSURE (LEVEL) TRANSMITTERS Installation of DP type/ DiaphragmSeal DP type Level Instrument including mounting on Yoke, supply of supportsfor impulse line/ capillary/ manifold, fabrication of manifolds and erectionwherever required, laying of capillary on supports, fabrication andinstallation of impulse lines with support as per Standard indicated below,hydraulic testing and painting of supports but exclusive of Supply ofInstrument, Piping material, all Electrical/ Pneumatic connections, Yoke andCalibration. Impulse lines made of Piping. _I150.10.11M02 In Carbon Steel as per Standard A620-000-16-51-IS25Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________DIFFERENTIAL PRESSURE (LEVEL) TRANSMITTERS Installation of DP type/ Diaphragm



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________Seal DP type Level Instrument including mounting on Yoke, supply of supportsfor impulse line/ capillary/ manifold, fabrication of manifolds and erectionwherever required, laying of capillary on supports, fabrication andinstallation of impulse lines with support as per Standard indicated below,hydraulic testing and painting of supports but exclusive of Supply ofInstrument, Piping material, all Electrical/ Pneumatic connections, Yoke andCalibration. Impulse lines made of Piping. _I150.10.11M02 In Carbon Steel as per Standard A620-000-16-51-IS25Payment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 120 5 NO

Inst. of LT : GWR with Chamber (Number) _________________________________________________________________

SPECIAL LEVEL/ GUIDED WAVE / ECCLIPSE TYPE RADAR LEVEL INSTRUMENTSInstallation of Guided Wave/ Ecclipse type radar level instruments with orwithout controllers including installation of instruments on nozzles, changingof head orientation wherever required, fabrication and installation of primarypiping, drain valve / vent valve assembly as per standard and hydraulictesting of instrument but exclusive of supply of instruments, pipingmaterials, all electrical/ pneumatic connections and calibration.I185.10.01M01 GWR Level instrument including chamber (if any) as per StandPayment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________SPECIAL LEVEL/ GUIDED WAVE / ECCLIPSE TYPE RADAR LEVEL INSTRUMENTSInstallation of Guided Wave/ Ecclipse type radar level instruments with orwithout controllers including installation of instruments on nozzles, changingof head orientation wherever required, fabrication and installation of primarypiping, drain valve / vent valve assembly as per standard and hydraulictesting of instrument but exclusive of supply of instruments, pipingmaterials, all electrical/ pneumatic connections and calibration.I185.10.01M01 GWR Level instrument including chamber (if any) as per StandPayment terms shall be as follows60% on completion of erection / installation.



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 130 4 NO

Inst. of LT : GWR Top mounted (Number) _________________________________________________________________

SPECIAL LEVEL/ GUIDED WAVE / ECCLIPSE TYPE RADAR LEVEL INSTRUMENTSInstallation of Guided Wave/ Ecclipse type radar level instruments with orwithout controllers including installation of instruments on nozzles, changingof head orientation wherever required, fabrication and installation of primarypiping, drain valve / vent valve assembly as per standard and hydraulictesting of instrument but exclusive of supply of instruments, pipingmaterials, all electrical/ pneumatic connections and calibration.I185.10.01M02 Top Mounted GWR Level InstrumentPayment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________SPECIAL LEVEL/ GUIDED WAVE / ECCLIPSE TYPE RADAR LEVEL INSTRUMENTSInstallation of Guided Wave/ Ecclipse type radar level instruments with orwithout controllers including installation of instruments on nozzles, changingof head orientation wherever required, fabrication and installation of primarypiping, drain valve / vent valve assembly as per standard and hydraulictesting of instrument but exclusive of supply of instruments, pipingmaterials, all electrical/ pneumatic connections and calibration.I185.10.01M02 Top Mounted GWR Level InstrumentPayment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 140 5 NO



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________Inst. of LG : CS Std A620-000-16-51-IS23 (Number)

_________________________________________________________________LEVEL GAUGES Installation of Level Gauges on Vessel/ Piping/ Standpipes withminor modification wherever required, fabrication of primary piping,fabrication and installation of drain valve/ vent valve assembly as perStandard indicated below, hydraulic testing of gauge, installation ofilluminators/ non-frosting extension if required but exclusive of Supply ofGauges, Illuminators and Piping material. _I200.10.11M01 In Carbon Steel as per Standard A620-000-16-51-IS23Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________LEVEL GAUGES Installation of Level Gauges on Vessel/ Piping/ Standpipes withminor modification wherever required, fabrication of primary piping,fabrication and installation of drain valve/ vent valve assembly as perStandard indicated below, hydraulic testing of gauge, installation ofilluminators/ non-frosting extension if required but exclusive of Supply ofGauges, Illuminators and Piping material. _I200.10.11M01 In Carbon Steel as per Standard A620-000-16-51-IS23Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 150 5 NO

Inst. of LG : CS Std 7-52-0483 (Number) _________________________________________________________________

LEVEL GAUGES Installation of Level Gauges on Vessel/ Piping/ Standpipes withminor modification wherever required, fabrication of primary piping,fabrication and installation of drain valve/ vent valve assembly as perStandard indicated below, hydraulic testing of gauge, installation ofilluminators/ non-frosting extension if required but exclusive of Supply ofGauges, Illuminators and Piping material. _I200.10.21 In CS as per Std. 7-52-0483Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________LEVEL GAUGES Installation of Level Gauges on Vessel/ Piping/ Standpipes withminor modification wherever required, fabrication of primary piping,fabrication and installation of drain valve/ vent valve assembly as perStandard indicated below, hydraulic testing of gauge, installation ofilluminators/ non-frosting extension if required but exclusive of Supply ofGauges, Illuminators and Piping material. _I200.10.21 In CS as per Std. 7-52-0483Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 160 50 NO

Inst of TG with thermowell (Number) _________________________________________________________________

TEMPERATURE INSTRUMENTSInstallation of Temperature Indicators/ Gauges (Filled system/ Bimetallic)RTD/ Thermocouple/ Temperature Switches/ Temperature transmitters with flangedthermowell inclusive of installation of machined/ builtup thermowells on thenozzle and installation of Instruments, Electrical/ Pneumatic connection butexclusive of Supply of Instruments/ Elements/ Thermowell, and Calibration.I330.10.12 Temperature Indicator/ Gauges (Bimetallic Type) with wellPayment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________TEMPERATURE INSTRUMENTSInstallation of Temperature Indicators/ Gauges (Filled system/ Bimetallic)RTD/ Thermocouple/ Temperature Switches/ Temperature transmitters with flangedthermowell inclusive of installation of machined/ builtup thermowells on thenozzle and installation of Instruments, Electrical/ Pneumatic connection butexclusive of Supply of Instruments/ Elements/ Thermowell, and Calibration.I330.10.12 Temperature Indicator/ Gauges (Bimetallic Type) with wellPayment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completion



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________certificate.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 170 10 NO

Inst of test thermowell (Number) _________________________________________________________________

TEMPERATURE INSTRUMENTSInstallation of Temperature Indicators/ Gauges (Filled system/ Bimetallic)RTD/ Thermocouple/ Temperature Switches/ Temperature transmitters with flangedthermowell inclusive of installation of machined/ builtup thermowells on thenozzle and installation of Instruments, Electrical/ Pneumatic connection butexclusive of Supply of Instruments/ Elements/ Thermowell, and Calibration.I330.10.17 Test Thermowell (flanged)Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________TEMPERATURE INSTRUMENTSInstallation of Temperature Indicators/ Gauges (Filled system/ Bimetallic)RTD/ Thermocouple/ Temperature Switches/ Temperature transmitters with flangedthermowell inclusive of installation of machined/ builtup thermowells on thenozzle and installation of Instruments, Electrical/ Pneumatic connection butexclusive of Supply of Instruments/ Elements/ Thermowell, and Calibration.I330.10.17 Test Thermowell (flanged)Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 180 50 NO

Inst of TT with TC and Thermowell (Number) _________________________________________________________________

TEMPERATURE TRANSMITTERS (REMOTE MOUNTED)Thermocouple/ RTD element with thermowell, along with Temperature Transmitterremote mounted. Installation of transmitter including mounting on yoke,fabrication and erection of supports with clamps and laying of extension/RTDcable upto thermocouple, termination of cables at both ends, painting of



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________supports but exclusive of Supply of Instruments, Cable, Yoke and Calibration._I340.10.11 Temperature Transmitter and Thermocouple with flanged wellPayment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________TEMPERATURE TRANSMITTERS (REMOTE MOUNTED)Thermocouple/ RTD element with thermowell, along with Temperature Transmitterremote mounted. Installation of transmitter including mounting on yoke,fabrication and erection of supports with clamps and laying of extension/RTDcable upto thermocouple, termination of cables at both ends, painting ofsupports but exclusive of Supply of Instruments, Cable, Yoke and Calibration._I340.10.11 Temperature Transmitter and Thermocouple with flanged wellPayment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 190 20 NO

Inst of TT only (Number) _________________________________________________________________

TEMPERATURE TRANSMITTERS (REMOTE MOUNTED)Thermocouple/ RTD element with thermowell, along with Temperature Transmitterremote mounted. Installation of transmitter including mounting on yoke,fabrication and erection of supports with clamps and laying of extension/RTDcable upto thermocouple, termination of cables at both ends, painting ofsupports but exclusive of Supply of Instruments, Cable, Yoke and Calibration._I340.10.11M01 Temperature Transmitter ONLYPayment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________TEMPERATURE TRANSMITTERS (REMOTE MOUNTED)



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________Thermocouple/ RTD element with thermowell, along with Temperature Transmitterremote mounted. Installation of transmitter including mounting on yoke,fabrication and erection of supports with clamps and laying of extension/RTDcable upto thermocouple, termination of cables at both ends, painting ofsupports but exclusive of Supply of Instruments, Cable, Yoke and Calibration._I340.10.11M01 Temperature Transmitter ONLYPayment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 200 5 NO

Inst of Temp MUX (Number) _________________________________________________________________

TEMPERATURE TRANSMITTERS (REMOTE MOUNTED)Thermocouple/ RTD element with thermowell, along with Temperature Transmitterremote mounted. Installation of transmitter including mounting on yoke,fabrication and erection of supports with clamps and laying of extension/RTDcable upto thermocouple, termination of cables at both ends, painting ofsupports but exclusive of Supply of Instruments, Cable, Yoke and Calibration._I340.10.11M02 8 Input Temperature MultiplexerPayment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________TEMPERATURE TRANSMITTERS (REMOTE MOUNTED)Thermocouple/ RTD element with thermowell, along with Temperature Transmitterremote mounted. Installation of transmitter including mounting on yoke,fabrication and erection of supports with clamps and laying of extension/RTDcable upto thermocouple, termination of cables at both ends, painting ofsupports but exclusive of Supply of Instruments, Cable, Yoke and Calibration._I340.10.11M02 8 Input Temperature MultiplexerPayment terms shall be as follows60% on completion of erection / installation.



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 210 10 NO

Inst of TT with RTD and Thermowell (Number) _________________________________________________________________

TEMPERATURE TRANSMITTERS (REMOTE MOUNTED)Thermocouple/ RTD element with thermowell, along with Temperature Transmitterremote mounted. Installation of transmitter including mounting on yoke,fabrication and erection of supports with clamps and laying of extension/RTDcable upto thermocouple, termination of cables at both ends, painting ofsupports but exclusive of Supply of Instruments, Cable, Yoke and Calibration._I340.10.13 Temperature Transmitter and RTD with flanged wellPayment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________TEMPERATURE TRANSMITTERS (REMOTE MOUNTED)Thermocouple/ RTD element with thermowell, along with Temperature Transmitterremote mounted. Installation of transmitter including mounting on yoke,fabrication and erection of supports with clamps and laying of extension/RTDcable upto thermocouple, termination of cables at both ends, painting ofsupports but exclusive of Supply of Instruments, Cable, Yoke and Calibration._I340.10.13 Temperature Transmitter and RTD with flanged wellPayment terms shall be as follows60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 220 5 NO



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________Loop checking : Pressure Switch (Number)

_________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.01 Pressure switchesPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.01 Pressure switchesPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 230 90 NO

Loop checking : Pressure transmitters (Number) _________________________________________________________________

LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.02 Pressure transmittersPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising the



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________loop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.02 Pressure transmittersPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 240 140 NO

Loop checking :DP Transmitters (Number) _________________________________________________________________

LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.05 DP Transmitters for Flow, Level and D.P.Payment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.05 DP Transmitters for Flow, Level and D.P.Payment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 250 230 NO

Loop checking :Temperature Transmitters (Number) _________________________________________________________________

LOOP CHECKING



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________Loop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.10 Temperature TransmittersPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.10 Temperature TransmittersPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 260 25 NO

Loop checking : Multi point TT (Number) _________________________________________________________________

LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.11 Mulitipoint Temperature Transmitters.Payment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.11 Mulitipoint Temperature Transmitters.



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________Payment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 270 13 NO

Loop Checking : GWR (Number) _________________________________________________________________

LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.12 Sp Level Instruments/ GWR/Ecclipse type level instrumentsPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.12 Sp Level Instruments/ GWR/Ecclipse type level instrumentsPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 280 5 NO

Loop Checking : I/P or P/I (Number) _________________________________________________________________

LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erection



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________tender 6-52-0060.I510.10.14 Current to Pneumatic convertorsPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.14 Current to Pneumatic convertorsPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 290 20 NO

Loop Checking : Local Indicator (Number) _________________________________________________________________

LOOP CHECKING Loop checking (excluding calibration/ testing) of theinstruments listed below including verifying the functional performance of allelements comprising the loop, thereby ensuring proper interconnections andoperation, with all other specifications inline with clause 4.13 of Standardspecification for Erection tender 6-52-0060.I510.10.15 Electronic Local IndicatorPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKING Loop checking (excluding calibration/ testing) of theinstruments listed below including verifying the functional performance of allelements comprising the loop, thereby ensuring proper interconnections andoperation, with all other specifications inline with clause 4.13 of Standardspecification for Erection tender 6-52-0060.I510.10.15 Electronic Local IndicatorPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________





_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 300 15 NO

Loop Checking : Vibration Switch (Number) _________________________________________________________________

LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.16 Vibration SwitchPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.16 Vibration SwitchPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 310 15 NO

Loop Checking : LELDetectors (Number) _________________________________________________________________

LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.17 LEL DetectorsPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.17 LEL DetectorsPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 320 90 NO

Loop checking : Control Valve (Number) _________________________________________________________________

LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.30M01 Control ValvePayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.30M01 Control ValvePayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________





_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 330 20 NO

Loop Checking :On-Off Valve (SDV/ROV) (Number) _________________________________________________________________

LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.30M02 On-Off Valve (SDV/ROV)Payment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.30M02 On-Off Valve (SDV/ROV)Payment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 340 5 NO

Loop Checking : Speed Transmitter (Number) _________________________________________________________________

LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.31 Speed TransmitterPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed below



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________including verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.31 Speed TransmitterPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 350 10 NO

Loop Checking : H2 Detectors (Number) _________________________________________________________________

LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.33M01 H2 DetectorsPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.33M01 H2 DetectorsPayment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 360 200 NO

Loop checking : MCC I/Os (Number) _________________________________________________________________



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.34M02 Loop checking of MCC I/O interface signals between DCS &Substation.Payment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________LOOP CHECKINGLoop checking (excluding calibration/ testing) of the instruments listed belowincluding verifying the functional performance of all elements comprising theloop, thereby ensuring proper interconnections and operation, with all otherspecifications inline with clause 4.13 of Standard specification for Erectiontender 6-52-0060.I510.10.34M02 Loop checking of MCC I/O interface signals between DCS &Substation.Payment terms shall be as follows.95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 370 3 NO

Inst of JB : for 6P x 0.5/ 1.5 mm² cable (Number) _________________________________________________________________

JUNCTION BOX INSTALLATION Installation of weatherproof and flameproof junction boxes including supply,fabrication and installation of supports, installation of junction boxes,laying and connection of earthing cable , screwing plugs for unused entriesand painting but exclusive of supply of junction boxes and glands/ fittingsand earthing cable. _

I600.20.01M01 For cable size 6P x 0.5/ 1.5 mm² Signal/ Alarm/ Control (withFlexible Copper cable of size 4 mm2 with green color outer PVC insulationinstead of GI wire for Earthing).Payment terms shall be as follows93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.




_________________________________________________________________JUNCTION BOX INSTALLATION Installation of weatherproof and flameproof junction boxes including supply,fabrication and installation of supports, installation of junction boxes,laying and connection of earthing cable , screwing plugs for unused entriesand painting but exclusive of supply of junction boxes and glands/ fittingsand earthing cable. _

I600.20.01M01 For cable size 6P x 0.5/ 1.5 mm² Signal/ Alarm/ Control (withFlexible Copper cable of size 4 mm2 with green color outer PVC insulationinstead of GI wire for Earthing).Payment terms shall be as follows93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 380 3 NO

Inst of JB : for 2 Pair FF cable (Number) _________________________________________________________________


I600.20.01M02 For FIeldbus Trunk Cable of size 2 Pair 16 AWG (with FlexibleCopper cable of size 4 mm2 with green color outer PVC insulation instead of GIwire for Earthing).Payment terms shall be as follows93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________JUNCTION BOX INSTALLATION Installation of weatherproof and flameproof junction boxes including supply,fabrication and installation of supports, installation of junction boxes,laying and connection of earthing cable , screwing plugs for unused entriesand painting but exclusive of supply of junction boxes and glands/ fittingsand earthing cable. _I600.20.01M02 For FIeldbus Trunk Cable of size 2 Pair 16 AWG (with FlexibleCopper cable of size 4 mm2 with green color outer PVC insulation instead of GI



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________wire for Earthing).Payment terms shall be as follows93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 390 3 NO

Inst of JB : for 12P x 0.5/ 1.5 mm² Cabl (Number) _________________________________________________________________


I600.20.05M01 For cable size 12P x 0.5/ 1.5 mm² Signal/ Alarm/ Control (withFlexible Copper cable of size 4 mm2 with green color outer PVC insulationinstead of GI wire for Earthing).Payment terms shall be as follows93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________JUNCTION BOX INSTALLATION Installation of weatherproof and flameproof junction boxes including supply,fabrication and installation of supports, installation of junction boxes,laying and connection of earthing cable , screwing plugs for unused entriesand painting but exclusive of supply of junction boxes and glands/ fittingsand earthing cable. __I600.20.05M01 For cable size 12P x 0.5/ 1.5 mm² Signal/ Alarm/ Control (withFlexible Copper cable of size 4 mm2 with green color outer PVC insulationinstead of GI wire for Earthing).Payment terms shall be as follows93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________





_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 400 3 NO

Inst of JB:For 8T x 1.5 mm² RTD/Detector (Number) _________________________________________________________________

JUNCTION BOX INSTALLATION Installation of weatherproof and flameproof junction boxes including supply,fabrication and installation of supports, installation of junction boxes,laying and connection of earthing cable , screwing plugs for unused entriesand painting but exclusive of supply of junction boxes and glands/ fittingsand earthing cable. _I600.20.43M01 For cable size 8T x 1.5 mm² RTD/ Gas Detector (with FlexibleCopper cable of size 4 mm2 with green color outer PVC insulation instead of GIwire for Earthing).Payment terms shall be as follows93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________JUNCTION BOX INSTALLATION Installation of weatherproof and flameproof junction boxes including supply,fabrication and installation of supports, installation of junction boxes,laying and connection of earthing cable , screwing plugs for unused entriesand painting but exclusive of supply of junction boxes and glands/ fittingsand earthing cable. _I600.20.43M01 For cable size 8T x 1.5 mm² RTD/ Gas Detector (with FlexibleCopper cable of size 4 mm2 with green color outer PVC insulation instead of GIwire for Earthing).Payment terms shall be as follows93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 410 2,000 M

Cable laying :FF cable 1/2/3/4 Pair (Meter) _________________________________________________________________

LAYING OF CABLES Laying of instrumentation cables for signal, alarm, shutdown, control andsignal cable on ducts, main trays, perforated trays, angle trays, trenches



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________(including opening of cable duct covers if required through IRCs {InstrumentRoad Crossings}) including clamping, glanding the cables, termination at bothends including shield/ drain/ communication wire, providing and fixingidentifying SS tag plates at both ends of cables and megger testing butexclusive of supply of cables and erection of ducts, main tray, perforatedtray/ angle trays and preparation of cable trench. This include supply ofrequired double compression type lugs, cable tie , white Silicon sleeve forferrule and its printing.I610.10.01M01 Fieldbus Trunk Cable of Size 1/2/3/4 Pair 16 AWGPayment terms shall be as follows:60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________LAYING OF CABLES Laying of instrumentation cables for signal, alarm, shutdown, control andsignal cable on ducts, main trays, perforated trays, angle trays, trenches(including opening of cable duct covers if required through IRCs {InstrumentRoad Crossings}) including clamping, glanding the cables, termination at bothends including shield/ drain/ communication wire, providing and fixingidentifying SS tag plates at both ends of cables and megger testing butexclusive of supply of cables and erection of ducts, main tray, perforatedtray/ angle trays and preparation of cable trench. This include supply ofrequired double compression type lugs, cable tie , white Silicon sleeve forferrule and its printing.I610.10.01M01 Fieldbus Trunk Cable of Size 1/2/3/4 Pair 16 AWGPayment terms shall be as follows:60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 420 30,000 M

Cable laying :1pair / 2core x 1.5 mm2 (Meter) _________________________________________________________________

LAYING OF CABLES Laying of instrumentation cables for signal, alarm, shutdown, control andsignal cable on ducts, main trays, perforated trays, angle trays, trenches(including opening of cable duct covers if required through IRCs {InstrumentRoad Crossings}) including clamping, glanding the cables, termination at both



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________ends including shield/ drain/ communication wire, providing and fixingidentifying SS tag plates at both ends of cables and megger testing butexclusive of supply of cables and erection of ducts, main tray, perforatedtray/ angle trays and preparation of cable trench. This include supply ofrequired double compression type lugs, cable tie , white Silicon sleeve forferrule and its printing._I610.10.01M02 Signal / Alarm / Control/ Spur Cables of cable sizes 1P x1.5mm2.Payment terms shall be as follows:60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________LAYING OF CABLES Laying of instrumentation cables for signal, alarm, shutdown, control andsignal cable on ducts, main trays, perforated trays, angle trays, trenches(including opening of cable duct covers if required through IRCs {InstrumentRoad Crossings}) including clamping, glanding the cables, termination at bothends including shield/ drain/ communication wire, providing and fixingidentifying SS tag plates at both ends of cables and megger testing butexclusive of supply of cables and erection of ducts, main tray, perforatedtray/ angle trays and preparation of cable trench. This include supply ofrequired double compression type lugs, cable tie , white Silicon sleeve forferrule and its printing.I610.10.01M02 Signal / Alarm / Control/ Spur Cables of cable sizes 1P x1.5mm2.Payment terms shall be as follows:60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 430 1,500 M

laying of 1 Pair x 16 AWG TC cable (Meter) _________________________________________________________________

Laying of cableLaying of thermocouple/ RTD/ LEL Detector/ H2S Detector cables on ducts, maintrays, perforated trays, angle trays, trenches (including through IRCs{Instrument Road Crossings}) including opening of cable duct covers ifrequired clamping, glanding the cables, termination at both ends including



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________shield/ drain/communication wire providing and fixing of identifying SS tagplate at both ends of cable and megger testing but exclusive of supply ofmulti cables and erection of ducts, main tray, perforated tray/angle tray andpreparation of cable trench. Exclusive of supply of cable glands, butincluding supply of required double compression type lugs, cable tie , whiteSilicon sleeve for ferrule and its printing.I610.30.21 1 Pair x 16 AWG Thermocouple CablePayment terms shall be as follows:60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________Laying of thermocouple/ RTD/ LEL Detector/ H2S Detector cables on ducts, maintrays, perforated trays, angle trays, trenches (including through IRCs{Instrument Road Crossings}) including opening of cable duct covers ifrequired clamping, glanding the cables, termination at both ends includingshield/ drain/communication wire providing and fixing of identifying SS tagplate at both ends of cable and megger testing but exclusive of supply ofmulti cables and erection of ducts, main tray, perforated tray/angle tray andpreparation of cable trench. Exclusive of supply of cable glands, butincluding supply of required double compression type lugs, cable tie , whiteSilicon sleeve for ferrule and its printing.I610.30.21 1 Pair x 16 AWG Thermocouple CablePayment terms shall be as follows:60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 440 3,000 M

Laying 1Triad x 1.5 mm² RTD/ LEL Cable (Meter) _________________________________________________________________

Laying of thermocouple/ RTD/ LEL Detector/ H2S Detector cables on ducts, maintrays, perforated trays, angle trays, trenches (including through IRCs{Instrument Road Crossings}) including opening of cable duct covers ifrequired clamping, glanding the cables, termination at both ends includingshield/ drain/communication wire providing and fixing of identifying SS tagplate at both ends of cable and megger testing but exclusive of supply ofmulti cables and erection of ducts, main tray, perforated tray/angle tray andpreparation of cable trench. Exclusive of supply of cable glands, butincluding supply of required double compression type lugs, cable tie , white



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________Silicon sleeve for ferrule and its printing._I610.30.41 1 Triad/ Quad x 1.5 mm² RTD/ LEL CablePayment terms shall be as follows:60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________Laying of thermocouple/ RTD/ LEL Detector/ H2S Detector cables on ducts, maintrays, perforated trays, angle trays, trenches (including through IRCs{Instrument Road Crossings}) including opening of cable duct covers ifrequired clamping, glanding the cables, termination at both ends includingshield/ drain/communication wire providing and fixing of identifying SS tagplate at both ends of cable and megger testing but exclusive of supply ofmulti cables and erection of ducts, main tray, perforated tray/angle tray andpreparation of cable trench. Exclusive of supply of cable glands, butincluding supply of required double compression type lugs, cable tie , whiteSilicon sleeve for ferrule and its printing.I610.30.41 1 Triad/ Quad x 1.5 mm² RTD/ LEL CablePayment terms shall be as follows:60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 450 1,000 M

Cable laying: 2C x 2.5 mm² /4 mm² /6 mm² (Meter) _________________________________________________________________

Laying of power cables on ducts, main trays, perforated trays, angle trays,trenches (including through IRCs) including opening of cable duct covers ifrequired clamping, glanding the cables, termination at both ends includingshield/ drain/ communication wire providing and fixing of identifying SS tagplates at both ends of cable and megger testing but exclusive of supply ofmulti cables and erection of ducts, main tray, perforated tray/ angle tray andpreparation of cable trench but including supply of required doublecompression type lugs, cable tie , white Silicon sleeve for ferrule and itsprinting._

I610.80.01M02 Size 2C x 2.5 mm² /4 mm² /6 mm²Payment terms shall be as follows:60% on completion of erection / installation.



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________Laying of power cables on ducts, main trays, perforated trays, angle trays,trenches (including through IRCs) including opening of cable duct covers ifrequired clamping, glanding the cables, termination at both ends includingshield/ drain/ communication wire providing and fixing of identifying SS tagplates at both ends of cable and megger testing but exclusive of supply ofmulti cables and erection of ducts, main tray, perforated tray/ angle tray andpreparation of cable trench but including supply of required doublecompression type lugs, cable tie , white Silicon sleeve for ferrule and itsprinting._

I610.80.01M02 Size 2C x 2.5 mm² /4 mm² /6 mm²Payment terms shall be as follows:60% on completion of erection / installation.33% on testing and loop checking02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 460 200 M

Tubing : 1/4"/ 6 mm O.D. SS316/CU tube (Meter) _________________________________________________________________

PIPING / TUBING / FABRICATION WORK _Laying of Bare/ PVC covered copper tubes/SS tubes on perforated trays including clamping, termination at both ends,providing identifying tags at both ends and Air testing, but exclusive ofsupply of copper/SS tubes, fitting and erection of perforated tray/ angletray. _I700.03.01 1/4"/ 6 mm O.D.Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________PIPING / TUBING / FABRICATION WORK _Laying of Bare/ PVC covered copper tubes/SS tubes on perforated trays including clamping, termination at both ends,providing identifying tags at both ends and Air testing, but exclusive ofsupply of copper/SS tubes, fitting and erection of perforated tray/ angletray. _I700.03.01 1/4"/ 6 mm O.D.



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 470 400 M

Tubing:1/2" O.D. SS Tube (Meter) _________________________________________________________________

PIPING / TUBING / FABRICATION WORK _Laying of Bare/ PVC covered copper tubes/SS tubes on perforated trays including clamping, termination at both ends,providing identifying tags at both ends and Air testing, but exclusive ofsupply of copper/SS tubes, fitting and erection of perforated tray/ angletray. _I700.03.15 1/2" O.D. (for analyzers in SS tubes)Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________PIPING / TUBING / FABRICATION WORK _Laying of Bare/ PVC covered copper tubes/SS tubes on perforated trays including clamping, termination at both ends,providing identifying tags at both ends and Air testing, but exclusive ofsupply of copper/SS tubes, fitting and erection of perforated tray/ angletray. _I700.03.15 1/2" O.D. (for analyzers in SS tubes)Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 480 6 NO

Tubing CV Std. A620-000-IS30 (Number) _________________________________________________________________

Tubing Hook-up of Control valves/ Pneumatic Transmitters etc. with air filterregulator / positioner / solenoid valves / Current to Pneumatic convertersetc. as per Standards. _I700.50.04M02 Control Valves with SMART/ FF Positioner as per std



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________A620-000-IS30Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________Tubing Hook-up of Control valves/ Pneumatic Transmitters etc. with air filterregulator / positioner / solenoid valves / Current to Pneumatic convertersetc. as per Standards. _I700.50.04M02 Control Valves with SMART/ FF Positioner as per stdA620-000-IS30Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 490 15 NO

Tubing CV Std. A620-000-16-51-IS34 (Number) _________________________________________________________________

Tubing Hook-up of Control valves/ Pneumatic Transmitters etc. with air filterregulator / positioner / solenoid valves / Current to Pneumatic convertersetc. as per Standards. _

I700.50.04M03 Control valve with Solenoid Valve as per A620-000-16-51-IS34Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________Tubing Hook-up of Control valves/ Pneumatic Transmitters etc. with air filterregulator / positioner / solenoid valves / Current to Pneumatic convertersetc. as per Standards. _

I700.50.04M03 Control valve with Solenoid Valve as per A620-000-16-51-IS34Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________





_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 500 60 NO

Tubing CV Std. A620-000-IS35 (Number) _________________________________________________________________

Tubing Hook-up of Control valves/ Pneumatic Transmitters etc. with air filterregulator / positioner / solenoid valves / Current to Pneumatic convertersetc. as per Standards. _

I700.50.04M04 Control Valve with SMART/ FF Positioner as per stdA620-000-IS35Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________Tubing Hook-up of Control valves/ Pneumatic Transmitters etc. with air filterregulator / positioner / solenoid valves / Current to Pneumatic convertersetc. as per Standards. _

I700.50.04M04 Control Valve with SMART/ FF Positioner as per stdA620-000-IS35Payment terms shall be as follows:93% on completion of erection / installation and testing.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 510 3,500 M

Trays of size 60 mm (W) x 30 mm (H) (Meter) _________________________________________________________________

Supply & Erection of prefabricated FRP perforated trays as per specificationattached elsewhere in the tender document and its support including tees,bends and elbows. This also includes one coat of primer as per IS:2074 and twocoats of finished paint for supports including supply of supports and paint asper standard.I800.81.01M01 Trays of size 60 mm (W) x 30 mm (H) without CoversPayment terms shall be as follows:65% after receipt and acceptance of fabricated materials( tray ) at site.25% after erection/installation



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________03% after welding final painting ,if any.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________Supply & Erection of prefabricated FRP perforated trays as per specificationattached elsewhere in the tender document and its support including tees,bends and elbows. This also includes one coat of primer as per IS:2074 and twocoats of finished paint for supports including supply of supports and paint asper standard.I800.81.01M01 Trays of size 60 mm (W) x 30 mm (H) without CoversPayment terms shall be as follows:65% after receipt and acceptance of fabricated materials( tray ) at site.25% after erection/installation03% after welding final painting ,if any.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 520 1,000 M


Supply & Erection of prefabricated FRP perforated trays as per specificationattached elsewhere in the tender document and its support including tees,bends and elbows. This also includes one coat of primer as per IS:2074 and twocoats of finished paint for supports including supply of supports and paint asper standard.I800.81.01M02 Trays of size 100 mm (W) x 50 mm (H) without CoversPayment terms shall be as follows:65% after receipt and acceptance of fabricated materials( tray ) at site.25% after erection/installation03% after welding final painting ,if any.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________Supply & Erection of prefabricated FRP perforated trays as per specificationattached elsewhere in the tender document and its support including tees,bends and elbows. This also includes one coat of primer as per IS:2074 and twocoats of finished paint for supports including supply of supports and paint asper standard.I800.81.01M02 Trays of size 100 mm (W) x 50 mm (H) without CoversPayment terms shall be as follows:65% after receipt and acceptance of fabricated materials( tray ) at site.



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________25% after erection/installation03% after welding final painting ,if any.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 530 1,000 M


Supply & Erection of prefabricated FRP perforated trays as per specificationattached elsewhere in the tender document and its support including tees,bends and elbows. This also includes one coat of primer as per IS:2074 and twocoats of finished paint for supports including supply of supports and paint asper standard.I800.81.01M03 Trays of size 150 mm (W) x 75 mm (H) without CoversPayment terms shall be as follows:65% after receipt and acceptance of fabricated materials( tray ) at site.25% after erection/installation03% after welding final painting ,if any.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________Supply & Erection of prefabricated FRP perforated trays as per specificationattached elsewhere in the tender document and its support including tees,bends and elbows. This also includes one coat of primer as per IS:2074 and twocoats of finished paint for supports including supply of supports and paint asper standard.I800.81.01M03 Trays of size 150 mm (W) x 75 mm (H) without CoversPayment terms shall be as follows:65% after receipt and acceptance of fabricated materials( tray ) at site.25% after erection/installation03% after welding final painting ,if any.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 540 200 M



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________Trays of size 300 mm (W) x 75 mm (H) (Meter)

_________________________________________________________________Supply & Erection of prefabricated FRP perforated trays as per specificationattached elsewhere in the tender document and its support including tees,bends and elbows. This also includes one coat of primer as per IS:2074 and twocoats of finished paint for supports including supply of supports and paint asper standard.I800.81.01M05 Trays of size 300 mm (W) x 75 mm (H) without CoversPayment terms shall be as follows:65% after receipt and acceptance of fabricated materials( tray ) at site.25% after erection/installation03% after welding final painting ,if any.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________Supply & Erection of prefabricated FRP perforated trays as per specificationattached elsewhere in the tender document and its support including tees,bends and elbows. This also includes one coat of primer as per IS:2074 and twocoats of finished paint for supports including supply of supports and paint asper standard.I800.81.01M05 Trays of size 300 mm (W) x 75 mm (H) without CoversPayment terms shall be as follows:65% after receipt and acceptance of fabricated materials( tray ) at site.25% after erection/installation03% after welding final painting ,if any.02% after mechanical completion05% after completion of all works in all respects and issuance of completioncertificate. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 550 750 NO

Sign Painting of Instruments (Number) _________________________________________________________________

I999.99.99V03 Identification of instrument items including sign paintingwherever required including supply of approved colour of paint/ paints(Fluorescent), painting of tag number (approx 25-50 mm high) on instrumentitem like transmitter, switches, level gauges, control valves etc. asspecified by Engineer-in-Charge.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________I999.99.99V03 Identification of instrument items including sign painting



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________wherever required including supply of approved colour of paint/ paints(Fluorescent), painting of tag number (approx 25-50 mm high) on instrumentitem like transmitter, switches, level gauges, control valves etc. asspecified by Engineer-in-Charge.Engineer-in-Charge.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 560 290 NO

Sign Painting of Junction boxes (Number) _________________________________________________________________

I999.99.99V04 Identification of Junction boxes including sign paintingwherever required including supply of approved colour of paint/ paints(Fluorescent), painting of tag number (approx 25-50 mm high) on junction boxesas specified by Engineer-in-Charge.Engineer-in-Charge.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________I999.99.99V04 Identification of Junction boxes including sign paintingwherever required including supply of approved colour of paint/ paints(Fluorescent), painting of tag number (approx 25-50 mm high) on junction boxesas specified by Engineer-in-Charge.Engineer-in-Charge.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge. _________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 570 250 MDY

Deployment of technician (Mandays) _________________________________________________________________

I999.99.99V23Deployment of Instrument Technicians for carryingout following majoractivities during Plant commissioning, post commissioning upto performanceGuarantee tests (PGTR) for the instrumentation system of NHT ISOM units along



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________with all types of test kits for various types of instruments as listed inSOR-Calibration / ReCalibration of field instruments during commissioning uptoPGTR. In case deployment for any technician is for a period less than a month,same shall be paid on pro-rata basis. Functional checks of instruments. Anyother requirement as & when required to assist our commissioning group duringcommissioning & PGTR as per the instructions of Engineer-in-charge. Providingassistance to Vendor's representatives deployed at site to attend to anyproblems related to instruments supplied by them. The technicians deployedshall have relevant experience and shall be deployed after obtaining approvalof their CV by Engineer-in-charge. Note: One Man Day is 12 Hrs duty on normalworking days.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________I999.99.99V23Deployment of Instrument Technicians for carryingout following majoractivities during Plant commissioning, post commissioning upto performanceGuarantee tests (PGTR) for the instrumentation system of NHT ISOM units alongwith all types of test kits for various types of instruments as listed inSOR-Calibration / ReCalibration of field instruments during commissioning uptoPGTR. In case deployment for any technician is for a period less than a month,same shall be paid on pro-rata basis. Functional checks of instruments. Anyother requirement as & when required to assist our commissioning group duringcommissioning & PGTR as per the instructions of Engineer-in-charge. Providingassistance to Vendor's representatives deployed at site to attend to anyproblems related to instruments supplied by them. The technicians deployedshall have relevant experience and shall be deployed after obtaining approvalof their CV by Engineer-in-charge. Note: One Man Day is 12 Hrs duty on normalworking days.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 580 30 MDY

Deployment of technician Holiday (Mandays) _________________________________________________________________

I999.99.99V24Deployment of Instrument Technicians for carryingout following major



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________activities during Plant commissioning, post commissioning upto performanceGuarantee tests (PGTR) for the instrumentation system of NHT ISOM units alongwith all types of test kits for various types of instruments as listed inSOR-Calibration / ReCalibration of field instruments during commissioning uptoPGTR. In case deployment for any technician is for a period less than a month,same shall be paid on pro-rata basis. Functional checks of instruments. Anyother requirement as & when required to assist our commissioning group duringcommissioning & PGTR as per the instructions of Engineer-in-charge. Providingassistance to Vendor's representatives deployed at site to attend to anyproblems related to instruments supplied by them. The technicians deployedshall have relevant experience and shall be deployed after obtaining approvalof their CV by Engineer-in-charge. Note: One Man Day is 12 Hrs duty on ClosedHolidays & Sundays.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________I999.99.99V24Deployment of Instrument Technicians for carryingout following majoractivities during Plant commissioning, post commissioning upto performanceGuarantee tests (PGTR) for the instrumentation system of NHT ISOM units alongwith all types of test kits for various types of instruments as listed inSOR-Calibration / ReCalibration of field instruments during commissioning uptoPGTR. In case deployment for any technician is for a period less than a month,same shall be paid on pro-rata basis. Functional checks of instruments. Anyother requirement as & when required to assist our commissioning group duringcommissioning & PGTR as per the instructions of Engineer-in-charge. Providingassistance to Vendor's representatives deployed at site to attend to anyproblems related to instruments supplied by them. The technicians deployedshall have relevant experience and shall be deployed after obtaining approvalof their CV by Engineer-in-charge. Note: One Man Day is 12 Hrs duty on ClosedHolidays & Sundays.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 590 250 MDY

Deployment of Electrician (Mandays) _________________________________________________________________

I999.99.99V25



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________"Deployment of Electricians for carrying out following major activities duringcommissioning, post commissioning upto performance Guarantee tests(PGTR) for the instrumentation system of NHT ISOM unit along with all types oftest kits for various types of instruments as listed in SOR- As & whenrequired to assist our commissioning group during commissioning & PGTR as perthe instructions of Engineer-in-charge. Providing assistance to Vendor'srepresentatives deployed at site to attend to any problems related toinstruments supplied by them. The Electricians deployed shall have relevantexperience and shall be deployed after obtaining approval of their CV byEngineer-incharge. Note: One Man Day is 12 Hrs duty on normal working days. Incase deployment for any electricians is for a period less than a month, sameshall be paid on pro-rata basis. "Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________I999.99.99V25"Deployment of Electricians for carrying out following major activities duringcommissioning, post commissioning upto performance Guarantee tests(PGTR) for the instrumentation system of NHT ISOM unit along with all types oftest kits for various types of instruments as listed in SOR- As & whenrequired to assist our commissioning group during commissioning & PGTR as perthe instructions of Engineer-in-charge. Providing assistance to Vendor'srepresentatives deployed at site to attend to any problems related toinstruments supplied by them. The Electricians deployed shall have relevantexperience and shall be deployed after obtaining approval of their CV byEngineer-incharge. Note: One Man Day is 12 Hrs duty on normal working days. Incase deployment for any electricians is for a period less than a month, sameshall be paid on pro-rata basis. "Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 600 25 MDY

Deployment of Electrician Holiday (Mandays) _________________________________________________________________

I999.99.99V26"Deployment of Electricians for carrying out following major activities duringcommissioning, post commissioning upto performance Guarantee tests(PGTR) for the instrumentation system of NHT ISOM unit along with all types of



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________test kits for various types of instruments as listed in SOR- As & whenrequired to assist our commissioning group during commissioning & PGTR as perthe instructions of Engineer-in-charge. Providing assistance to Vendor'srepresentatives deployed at site to attend to any problems related toinstruments supplied by them. The Electricians deployed shall have relevantexperience and shall be deployed after obtaining approval of their CV byEngineer-incharge. Note: One Man Day is 12 Hrs duty on Closed Holidays &Sundays."Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________I999.99.99V26"Deployment of Electricians for carrying out following major activities duringcommissioning, post commissioning upto performance Guarantee tests(PGTR) for the instrumentation system of NHT ISOM unit along with all types oftest kits for various types of instruments as listed in SOR- As & whenrequired to assist our commissioning group during commissioning & PGTR as perthe instructions of Engineer-in-charge. Providing assistance to Vendor'srepresentatives deployed at site to attend to any problems related toinstruments supplied by them. The Electricians deployed shall have relevantexperience and shall be deployed after obtaining approval of their CV byEngineer-incharge. Note: One Man Day is 12 Hrs duty on Closed Holidays &Sundays."Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 610 250 MDY

Deployment of Fitter (Mandays) _________________________________________________________________

I999.99.99V27Deployment of Fitters for carrying out following major activities (but notlimited to) during pre-commissioning and commissioning upto performanceGuarantee tests (PGTR) for the instrumentation system of NHT ISOM project suchas repairing the tubings & hook-ups damaged during pre-commissioning andcommissioning activies, some necessary modifcations in the impulse lines,providing assistance to Vendor's representatives deployed at site to attend toany problems related to instruments supplied by them, along with all necessarykits for various types of instruments as listed in SOR- As & when required to



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________assist our commissioning group during commissioning & PGTR as per theinstructions of Engineer-in-charge. The fitters deployed shall have relevantexperience and shall be deployed after obtaining approval of their CV byEngineer-incharge. Note: One Man Day is 12 Hrs duty on normal working days. Incase deployment for any fitter is for a period less than a month, same shallbe paid on pro-rata basis.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________I999.99.99V27Deployment of Fitters for carrying out following major activities (but notlimited to) during pre-commissioning and commissioning upto performanceGuarantee tests (PGTR) for the instrumentation system of NHT ISOM project suchas repairing the tubings & hook-ups damaged during pre-commissioning andcommissioning activies, some necessary modifcations in the impulse lines,providing assistance to Vendor's representatives deployed at site to attend toany problems related to instruments supplied by them, along with all necessarykits for various types of instruments as listed in SOR- As & when required toassist our commissioning group during commissioning & PGTR as per theinstructions of Engineer-in-charge. The fitters deployed shall have relevantexperience and shall be deployed after obtaining approval of their CV byEngineer-incharge. Note: One Man Day is 12 Hrs duty on normal working days. Incase deployment for any fitter is for a period less than a month, same shallbe paid on pro-rata basis.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 620 25 MDY

Deployment of Fitter Holiday (Mandays) _________________________________________________________________

I999.99.99V28Deployment of Fitters for carrying out following major activities (but notlimited to) during pre-commissioning and commissioning upto performanceGuarantee tests (PGTR) for the instrumentation system of NHT ISOM project suchas repairing the tubings & hook-ups damaged during pre-commissioning andcommissioning activies, some necessary modifcations in the impulse lines,providing assistance to Vendor's representatives deployed at site to attend toany problems related to instruments supplied by them, along with all necessary



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________kits for various types of instruments as listed in SOR- As & when required toassist our commissioning group during commissioning & PGTR as per theinstructions of Engineer-in-charge. The fitters deployed shall have relevantexperience and shall be deployed after obtaining approval of their CV byEngineer-incharge. Note: One Man Day is 12 Hrs duty on Closed Holidays &Sundays.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________I999.99.99V28Deployment of Fitters for carrying out following major activities (but notlimited to) during pre-commissioning and commissioning upto performanceGuarantee tests (PGTR) for the instrumentation system of NHT ISOM project suchas repairing the tubings & hook-ups damaged during pre-commissioning andcommissioning activies, some necessary modifcations in the impulse lines,providing assistance to Vendor's representatives deployed at site to attend toany problems related to instruments supplied by them, along with all necessarykits for various types of instruments as listed in SOR- As & when required toassist our commissioning group during commissioning & PGTR as per theinstructions of Engineer-in-charge. The fitters deployed shall have relevantexperience and shall be deployed after obtaining approval of their CV byEngineer-incharge. Note: One Man Day is 12 Hrs duty on Closed Holidays &Sundays.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 630 150 MDY

Deployment of Welder (Mandays) _________________________________________________________________

M14201000000 SKILLED Manpower with hand tools, including consumables(electrodes, filler wire, gas, cardboard, target plate, scaffolding etc, asrequired). Deployment of Welder for carrying out following major activities(but not limited to) during pre-commissioning and commissioning uptoperformance Guarantee tests (PGTR) for the instrumentation system of NHT ISOMproject such as repairing the Impulse hook-ups damaged duringpre-commissioning and commissioning activies, some necessary modifcations inthe impulse lines, providing assistance to Vendor's representatives deployedat site - As & when required to assist our commissioning group during



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________commissioning & PGTR as per the instructions of Engineer-in-charge. Thewelders deployed shall have relevant experience and shall be deployed afterobtaining approval of their CV by Engineer-incharge. Note: One Man Day is 12Hrs duty on normal working days. In case deployment for any welder is for aperiod less than a month, same shall be paid on pro-rata basis.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________M14201000000 SKILLED Manpower with hand tools, including consumables(electrodes, filler wire, gas, cardboard, target plate, scaffolding etc, asrequired. Deployment of Welder for carrying out following major activities(but not limited to) during pre-commissioning and commissioning uptoperformance Guarantee tests (PGTR) for the instrumentation system of NHT ISOMproject such as repairing the Impulse hook-ups damaged duringpre-commissioning and commissioning activies, some necessary modifcations inthe impulse lines, providing assistance to Vendor's representatives deployedat site - As & when required to assist our commissioning group duringcommissioning & PGTR as per the instructions of Engineer-in-charge. Thewelders deployed shall have relevant experience and shall be deployed afterobtaining approval of their CV by Engineer-incharge. Note: One Man Day is 12Hrs duty on normal working days. In case deployment for any welder is for aperiod less than a month, same shall be paid on pro-rata basis.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 640 30 MDY

Deployment of Welder Holiday (Mandays) _________________________________________________________________

M14201000000 SKILLED Manpower with hand tools, including consumables(electrodes, filler wire, gas, cardboard, target plate, scaffolding etc, asrequired). Deployment of Welder for carrying out following major activities(but not limited to) during pre-commissioning and commissioning uptoperformance Guarantee tests (PGTR) for the instrumentation system of NHT ISOMproject such as repairing the Impulse hook-ups damaged duringpre-commissioning and commissioning activies, some necessary modifcations inthe impulse lines, providing assistance to Vendor's representatives deployedat site - As & when required to assist our commissioning group duringcommissioning & PGTR as per the instructions of Engineer-in-charge. The



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________welders deployed shall have relevant experience and shall be deployed afterobtaining approval of their CV by Engineer-incharge. Note: One Man Day is 12Hrs duty on Holiday & Sundays. In case deployment for any welder is for aperiod less than a month, same shall be paid on pro-rata basis.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________M14201000000 SKILLED Manpower with hand tools, including consumables(electrodes, filler wire, gas, cardboard, target plate, scaffolding etc, asrequired). Deployment of Welder for carrying out following major activities(but not limited to) during pre-commissioning and commissioning uptoperformance Guarantee tests (PGTR) for the instrumentation system of NHT ISOMproject such as repairing the Impulse hook-ups damaged duringpre-commissioning and commissioning activies, some necessary modifcations inthe impulse lines, providing assistance to Vendor's representatives deployedat site - As & when required to assist our commissioning group duringcommissioning & PGTR as per the instructions of Engineer-in-charge. Thewelders deployed shall have relevant experience and shall be deployed afterobtaining approval of their CV by Engineer-incharge. Note: One Man Day is 12Hrs duty on Holiday & Sundays. In case deployment for any welder is for aperiod less than a month, same shall be paid on pro-rata basis.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 650 300 MDY

Deployment of Helper (Semi Skilled) (Mandays) _________________________________________________________________

I999.99.99V29"Deployment of Helpers (semi skilled) to assist Technician/ Electrician/Fitter during commissioning, post commissioning upto performance Guaranteetests(PGTR) for the instrumentation system of NHT ISOM unit as per the instructionsof Engineer-in-charge. Note: One Man Day is 12 Hrs duty on normal workingdays. In case deployment for any technician is for a period less than a month,same shall be paid on pro-rata basis."Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by Engineer



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________In charge.

_________________________________________________________________I999.99.99V29"Deployment of Helpers (semi skilled) to assist Technician/ Electrician/Fitter during commissioning, post commissioning upto performance Guaranteetests(PGTR) for the instrumentation system of NHT ISOM unit as per the instructionsof Engineer-in-charge. Note: One Man Day is 12 Hrs duty on normal workingdays. In case deployment for any technician is for a period less than a month,same shall be paid on pro-rata basis."Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________


_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 660 20 MDY

Deployment of Helper Holiday (Mandays) _________________________________________________________________

I999.99.99V30"Deployment of Helpers (semi skilled) to assist Technician/ Electrician/Fitter during commissioning, post commissioning upto performance Guaranteetests(PGTR) for the instrumentation system of NHT ISOM unit as per the instructionsof Engineer-in-charge. Note: One Man Day is 12 Hrs duty on Holidays &Sundays."Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge.

_________________________________________________________________I999.99.99V30"Deployment of Helpers (semi skilled) to assist Technician/ Electrician/Fitter during commissioning, post commissioning upto performance Guaranteetests(PGTR) for the instrumentation system of NHT ISOM unit as per the instructionsof Engineer-in-charge. Note: One Man Day is 12 Hrs duty on Holidays & Sundays.Payment terms shall be as follows:95% on completion of work on pro-rata basis as certified in monthly bill.05% after completion of all works in all respects and acceptance by EngineerIn charge." _________________________________________________________________





_____________________________________________________________________________________________________________________________________________________________________________________________________________________ 670 300 NO

Supply of Stanchion / Yoke support (Number) _________________________________________________________________

I999.99.99.V20Supply of 2 inch yoke supports/ stanchion for single instrument (prefabricated / fabrication at site) including shot blasting and painting ,for supporting transmitters / preamplifiers (with canopy) at a clear height of1.5 meter above finisher floor level, including erection of stanchion withnecessary supports. Painting of yoke supports after modification,if any. twocoat of final paint and one coat of primer shall be applied on the stanchinsover and above shotblasting. supply of paint shall be included in contractorsscope. Exclusive of mounting of instruments.Payment terms shall be as follows:65% on receipt and acceptance of material at site.28% on completion of erection /installation and testing.02% after mechanical completion.05% on completion of all works in all respect and issuance of completioncertificate.

_________________________________________________________________I999.99.99.V20Supply of 2 inch yoke supports/ stanchion for single instrument (prefabricated / fabrication at site) including shot blasting and painting ,for supporting transmitters / preamplifiers (with canopy) at a clear height of1.5 meter above finisher floor level, including erection of stanchion withnecessary supports. Painting of yoke supports after modification,if any. twocoat of final paint and one coat of primer shall be applied on the stanchinsover and above shotblasting. supply of paint shall be included in contractorsscope. Exclusive of mounting of instruments.Payment terms shall be as follows:65% on receipt and acceptance of material at site.28% on completion of erection /installation and testing.02% after mechanical completion.05% on completion of all works in all respect and issuance of completioncertificate. _________________________________________________________________


_______________________________________________________________________Service Tax%____________ VAT%________________ CST%________________

_____________________________________________________________________________________________________________________________________________________________________________________________________________________




* 10 Scope of WorkINSTRUMENTATION WORKS FOR ISOM PROJECT:

1) INTRODUCTION :

We are required to facilitate NHT/ISOM project activites by carrying outInstrumentation works at ISOM Site in the refinery.

Contractor should apprise himself of all the conditions prevailing in suchlocation and the restrictions placed on movement of personnel and equipment,types of equipment and tools permitted, working method allowed etc.in thelight of security and safety regulations operative in the area.

2) SCOPE OF WORK :

The scope of work covers under this contract is to carry out various kinds ofInstrumentation related works for erection & commissioning of ISOM Projectsite located inside the refinery premises.The contractor shall carry out alltypes of works listed in 'Schedule of rates' As and when required.

3) SPECIAL CONDITIONS OF CONTRACT :

Please note that "Scope of Work" will be read along with the 'SpecialConditions' of this contract. Contractor shall be required to abide by theconditions stated in General terms & conditions attached.

3.1. Prior to quoting for the job, the bidder will be required to visit thesite & clarify all the doubts (if any) from Engineer- in-charge. Otherwise itwill be presumed that the party has understood the work in all respect.

3.2 FIRE & SAFETY REGULATIONS

3.2.1 The work shall be carried out in a safe manner as per Refinery Fire &Safety Rules & Regulations. Work permit condition shall be scrupulouslyfollowed.

3.2.2 BPCL conducts an intensive training programme on various aspects of Fire& Safety, on regular basis, at Refinery-Fire Station. It is the responsibilityof the Contractor to nominate all the supervisors/labours (likely to beemployed for this job) for training through BPCL site engineer. The successfulcompletion of training is mandatory requirement (in addition to otherqualifications/experiences mentioned earlier) for any supervisor/labour to beeligible for working at Refinery work site. Failing which no supervisor/labourwill be deputed for working at Refinery work site. Contractor shall also sendall the other workmen deployed at Refinery for this training.

3.2.3 Contractor shall arrange all required safety gadgets like safety helmet,



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________safety Belt, safety shoes, Boiler suit, Gloves, safety Goggles etc. for theirworkmen.

3.2.4 Contractor shall submit detail safety action plan & quality assuranceplan before start of work within 7 days from the date of award of contract &get it approved from BPCL.

3.3 MOBILIZATION & TIME SCHEDULE OF WORK.

3.3.1 Within 7 days of issue of contract letter the contractor shall mobiliseall necessary manpower & equipments & start the job at site as directed.

3.3.2 The contractual completion period shall be Two months from the date ofaward of job. The mobilization & detailed schedule of activities forcompletion of the specified works shall be submitted by contractor shall gotit approved from BPCL/EIL. Prices quoted shall be valid considering all above.

3.4 SCOPE OF SUPPLY :

3.4.1 BY BPCL/EIL (free issue): Instruments (Transmitters, Impulsefabrication pipes etc.)

3.4.2 BY BPCL (Chargeable): Water, Power.

3.4.3 BY CONTRACTOR: All the material, Equipmets To complete the work as perscope of work & as specified in SOR.

3.5 TECHNICAL PERSON AT SITE/DEPLOYMENT OF ENGINEER

The contractor shall depute experienced/qualified (Degree/diploma Holder)Instrumentation persons with safety trained supervisors for site job.Contractor shall sufficient manpower during agreed working period to ensureeffective output to meet the agreed schedule/ bar chart.

3.6 DRAWING & DOCUMENTS:

Detailed construction drawings & other related documents on the basis of whichactual execution of the work shall be carried out will be made available tothe contractor after the award of the work. After issuance of constructiondrawing, contractor shall take actual site measurements, sort out discrepancyif any between drawing & actual site condition. After sorting out thediscrepancy if any, contractor shall intimate the same to EIL/BPCL and executethe work.

3.7.1 Water & Power :

A) Water: Water shall be provided to the CONTRACTOR at one point, subject to



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________availability, on chargeable basis. The CONTRACTOR shall at his own costarrange for tapping, storage tank & distribution required for his workincluding supply, installation & calibration of water meters. The presentcharge for Water is Rs. 79.31 / CUM which may change in accordance with changeof rate by Muncipal authorities. Non availability of water through BPCL shouldnot be a case for extra claim or time extension. Therefore, the CONTRACTORshall, within the quoted price, make alternate arrangement to cope with sucheventuality. Additional water, if required, to meet the contractualrequirements, shall be arranged by the CONTRACTOR at his own cost.

B) Power: Construction power shall be provided to the CONTRACTOR at one point,subject to availability, on chargeable basis. The charge for Electricity willbe Rs. 9.5 / kWh. All the works related to laying of cable / distributionpanel etc. for construction power shall be arranged by CONTRACTOR at his owncost including supply, installation & calibration of energy meters. The costof power supply shall be recovered by the BPCL every month (without prejudiceto any other mode of recovery available to the BPCL) by deduction from theCONTRACTOR'S bills.The energy meter to be installed by the CONTRACTOR shall be tested andcertified by State Electricity Board or any other agency approved by the BPCL.The construction power shall bemade available to the CONTRACTOR subject to grid disturbance, and no extensionof time or compensation shall be payable on this account. Therefore, theCONTRACTOR shall, within thequoted price, make alternate arrangement to cope with such eventuality.Additional power, if required, to meet the contractual requirements, shall bearranged by the CONTRACTOR at his own cost.

3.7.2 All other construction materials & equipments, oxygen & acetylene gases,consumables, transport, foundation bolts, nuts & Structural steel, etc.labour & supervision all necessary for completion of the job in totality. Thecontractor without prejudice to the responsibilities to execute and completethe work as per the specifications and time schedule , progressively deployconstruction equipment, tools and tackles and further augment the samedepending on the exegencies of work and as directed by the Engineer in chargeso as to suit the construction schedule within scheduled completion datewithout any additional cost to the Owner.

3.7.3 WORK TIMINGS :

Normal working hours for carrying out this job will be morning shift 07.45 amto evening 07.45pm, and Night shift shall be 07:45 pm to 07:45 am. Contractormay have to work in extended hours and on holidays if required to meet theproject schedule as instructed by Engineer-in-charge after taking allnecessary permissions from BPCL.



Item Material Qty Unit Unit Basic Rate Description Delivery date (in Figures)_______________________________________________________________________For execution of this job, contractor shall be required to get clearances fromBPCL. The work shall be carried out in a safe manner as per Refinery norms &work permit condition shall be scrupulously followed. The work should beplanned and undertaken only under the Supervision of a competent person. Noidle time wages or compensation for temporary stoppages of work orrestrictions would be paid and the rate quoted for various items of workshould cover the cost of all such contingencies and eventualities. Substantialstructures and utilities exist both above ground and underground, adjacent tothe work site, Special care is necessary in transportation, storage, workingon equipments and other construction activities to protect the existingfeatures and prevent damage to any facility. Necessary protective structures,barricades etc. have to be erected at various places as directed by Engineerin charge. No extra payment of such protective work will be made. All roadsand open areas adjacent to the work site shall either be closed or suitablyprotected as per the job requirement.

3.8 INSPECTION OF CONSTRUCTION MATERIAL & WORKS: All Instrumentation worksshall be offered for BPCL/EIL inspection. All material procured by thecontractor shall be offered for inspection as per approved ITP & supportedwith the test certificates of the tests conducted as per the relevant IS,BS,API,etc. codes. All tests shall be conducted through laboratories approved byBPCL/EIL.

3.9 HOUSE KEEPING: The contractor shall maintain good house keeping on day today basis at the site/fabrication yard. All construction material brought bythe contractor (like scaffolding pipes, metal pieces etc.), Cable scrap (likesheathe, armour of cable etc.) & other debris generated at site shall bestacked neatly in well defined spaces at no extra cost. Additional man- poweras & when required for housekeeping shall be arranged by contractorimmediately as per direction of Engineer-in-charge. Certified copy of gatepasses shall be attached with the final bill. Metal scrap,cable scrap or anyother scrap including wooden material shall be disposed categorywise at hisown cost as indicated by the Engineer in Charge.

The financial implication of above, if any should be taken care in the quotedrate and no seperate claim shall be entertained on this account. The finalbill of the contractor shall be linked with the area cleaning in all respectsincluding disposal of debries/scrap etc. to the entire satisfaction ofEngineer in charge.

3.10 MEASUREMENT OF WORKS FOR PAYMENT: -

Measurement of works shall be done as per standard procedure of measurementwhich is attached elsewhere in the tender.

3.11 BILLING: Contractor shall be paid against R.A. bills for the work done onthe basis of item rates as agreed in the contract.




Contractors bill for executed works shall be accepted only when jointlycertified (contractor & EIL) & signed measurements for the said works areenclosed.

Final bill shall be submitted along with jointly certified & signedmeasurements within 2 months from the date of completion of total work.

4. PAYMENT TERMS: Payment terms has been indicated against each item in theSOR.

10% of all RA bills shall be withheld as retention money. In lieu of retentionmoney, contractor shall submit bank guarantee of 10% of contract value alongwith acknowledgement of purchase order valid for defect liability period oftwelve months from the date of completion of contract with claim period sixmonths extra.

4.1 DEFECT LIABILITY PERIOD:- Defect liability period shall be 12 months fromthe date of completion of all the jobs covered under this contract.

Applicable taxes and duties shall be paid after due verifcation. Break up ofbasic cost for all items, and tax and duties shall be provided in allinvoices.

5. COMPLETION PERIOD: The contractual completion period shall be Two monthsfrom the date of LOI / Work order whichever is earlier.

LD clause - In case of delay, 0.5% / week of delay or part thereof up to amaximum 5% of the total purchase order value shall be recovered. ________________________________________________________________________________________________________________________________________

* 20 General Conditions of contract_______________________________________________________________________* 30 General Terms & Conditions_______________________________________________________________________* 40 Special Safety conditions_______________________________________________________________________* 50 Integrity Pact_______________________________________________________________________* 60 QEHS Policy_______________________________________________________________________* 70 Energy Policy_______________________________________________________________________* 80 Technical Attachments_______________________________________________________________________* 90 Financial Deterrent_______________________________________________________________________ Grand Total (inclusive of all taxes, duties/charges etc) In figure: In Words :

_______________________________________________________________________



TERMS & CONDITIONS_______________________________________________________________________ Important Notice_______________________________________________________________________ Sr.No Description_______________________________________________________________________ 001 Quotation received after due date will not be entertained

002 Your quotation must specify exact amount or percentage discount, Excise, S.T., Charges, Transport, Packing & forwarding, Octroi, etc. as applicable.

003 In case you are unable to quote, kindly send the quotation with a regret for our records. Non-receipt of a regret will adversely affect your vendor rating.

004 No quotation will be accepted without your rubber stamp and signature.

005 Your quotation must be strictly in enclosed envelope indicating Collective RFQ No., RFQ No. and due date.

006 For all future correspondences please mention the vendor code Collective RFQ Number & RFQ Number.

007 Retention Money 10 % shall stand deducted from each and every running bill submitted in the event of contract is awarded.

LIST OF ENCLOSURES1. Scope of Work2. General Conditions of contract3. General Terms & Conditions4. Special Safety conditions5. Integrity Pact6. QEHS Policy7. Energy Policy8. Technical Attachments9. Financial Deterrent



-------Tear off Portion to be pasted on the envelope containing offer------------_______________________________________________________________________

Collective RFQ No. : 1000263787

Our Reference: Due Date : 05.09.2016RFQ No. : 6000969611 Due Time : 12:00:00Subject:

To,

Purchase Group : N44-ISOM SER PROC_______________________________________________________________________

