in-line pumps lp(-e)/lpe-e - teral.info · suction total head (suction height + suction piping...

In-line pumps

LP(-e)/LPE-e

50Hz

E-CAT5-P-LPeLP-00-A

LP 32 A 5 .75 　 - e

①Model②Nominal diameter (32mm)③Type④Frequency (50Hz)⑤Output (0.75kW)⑥Phase (S: Single-phase, None: 3-phase)⑦Motor efficiency　None: Standard efficiency (equivalent to IE1)　e: Top Runner efficiency (equivalent to IE3)

① ② ③ ④ ⑤ ⑥ ⑦LPE 150 K - 5 15 - e

① ② ③ ⑤ ⑥④

* Please note that some of the devices in the photo may differ from actual devices in coating color, etc.

■Applications

■Features

●Circulation of cold/warm water

●Cooling and air-conditioning systems

●General water supply

●Pressurization of tap water

●Pressurization of industrial water

●Other uses

①Energy-saving pump with a Top Runner efficiency (equivalent to IE3) motor.　(Excluding pumps of single-phase and 3-phase 0.15kW or less. Pumps of

3-phase 0.25 to 0.4kW are our high efficiency standard products.)② Installable in the middle of piping, and does not require large installation

space.③ Compact, lightweight, and easy-to-handle because disassembly and

inspection can be performed without removing piping.④ No water leakage through the adoption of a mechanical seal.⑤ Usable for high-temperature and high-pressure water, and suitable as a

circulating pump of cold/warm water.⑥ Easy maintenance (Nominal diameter： 125~200mm)　When replacing the mechanical seal, it is unnecessary to disassemble the

pump and remove the motor. In addition, it is possible to replace the LPE model in shorter time than the conventional model.

⑦ Capable of high back pressure spec (Nominal diameter： 125~200mm)　Allowable boost pressure up to 1.6MPa supported by simple and

high-rigidity structure based on rational design.⑧ Space-saving (Nominal diameter： 125~200mm)　Installable in places where horizontal pumps would be hard to install. The

installation area is approx. 50% compared with our SJ4-e and SKJ-e models of horizontal pumps having comparable output.

⑨ High efficiency of pump (nominal diameter: 125~200mm)　Increase in efficiency by 5 to 10% from conventional pumps by optimum

design based on three-dimensional flow analysis and structural analysis.⑩ Compatible mounting dimension with conventional pumps.　(Some LPE models require special accessory.)

■Description of types

①Model (LPE, LP *)②Nominal diameter (150mm)③Type　* LP is only for 200J.④Frequency (50Hz)⑤Output (15kW)⑥Motor efficiency (Top Runner efficiency :equivalent to IE3)

LP(-e)/LPE-eVolute pumps 2-pole/4-pole, line-shapedCast-iron

2

■Standard specifications●Nominal diameter: 25～100mm

■Special accessories

■Supplementary table

Companion flange……Packings, bolts, and nuts included (Nominal diameter: 32~100mm), sluice valve, check valve, pressure gauge, vacuum gauge, compound gauge, foot valve, welded flange, vibration isolator, spacer (bore diameter 125~200mm: for adjustment of discharge height)　

●Nominal diameter: 125～200mm

*1 Contact us for use of brine because it depends on liquid quality.*2 Confirm that the following calculation equation is met. Suction total head (suction height + suction piping loss) ≤ Liquid level atmospheric pressure (10.3m) – NPSHR (Net Positive Suction Head Required) *3 × Margin ratio (1.3)*3 For NPSHR, refer to the graph of Net Positive Suction Head Required.

Fresh water (brine supported as custom-made) *1

0～ 80°CDetermined by liquid temperature, NPSHR and piping

loss on the suction side *2

See the Specification table.Closed

Mechanical seal(SiC vs Carbon)

Sealed ball bearingSCS13

（200J：CAC406）SUS420J2FCD450

Totally enclosed fan-cooled Outdoor type3-phase, 200V (7.5kW or less)

3-phase, 200/400V (11kW or more)1500min-1

JIS 10K standard type

Pumpingliquid

Structure

Material

Motor

Liquid qualityLiquid temperature

Impeller

Shaft seal

Bearing

Impeller

Motor shaftCasingType

Power source

Synchronous rotation speed

Total suction head(In case of 20°C)

Allowable pushing pressure

Flange spec

■Standard accessories

Special companion flange (bolt, nut and packing included) ……………2 sets

●Nominal diameter: 25mm

Packing for flange and coupling cover ……………………………………1 set


*1 For more than 80°C, contact us separately.*2 Pumps of LP25A, single-phase and 3-phase 0.08kW or less cannot pump up.*3 Refer to the supplemental table shown below for LP25A.*4 The impeller material for LP32A is PPS (polyphenylene sulfide resin).

*1 Not available for LP25A, LP40A and LP50A.

0.04,0.05,0.080.150.250.080.25

PPS resinNORYL resin

SUS304PPS resinSUS304

SUS430SUS303SUS304SUS430SUS304

FC180(EPDM)FC150(NBR)FC200(NBR)

FC180(EPDM)FC200(NBR)

Single-phase,100V

Phase and voltage OutputkW

Shaft materialCasing material(O-ring material)Impeller material

3-phase,200V

Fresh water0~90°C…(0.15kW or less)

0~80°C…(0.25kW or more) *1

−6m *2

For use with the total head 10m or less, take 60% or less of the total head.

See the specification table.Closed

Mechanical sealSealed ball bearing

CAC406 *4

SUS304 (3-phase). See the table below.SUS304 (single-phase, 0.25kW, 0.4kW)

FC200Standard efficiency (equivalent to IE1): Single-phase, 3-phase 0.15kW or less

Top Runner efficiency (equivalent to IE3): 3-phase 0.25kW or moreTotally enclosed self-cooled outdoor type: Single-phase 0.08kW or less,

3-phase 0.08kW, 0.25kWDrip-proof protected type: Single-phase 0.15kW or more, 3-phase 0.15kW

Totally enclosed fan-cooled outdoor type: 0.4kW or moreSingle-phase, 100V (0.05~0.4kW)3-phase, 200V (0.08kW or more)

3000min-1

Special companion flange for nominal diameter 25mmJIS 10K thin type for nominal diameter 32mm or more

Pumpingliquid

Structure

Material *3

Motor

Liquid quality

Liquid temperature

ImpellerShaft sealBearingImpeller

Shaft

Casing

Efficiency

Type

Power source

Synchronous rotation speed

Total suction head(In case of 20°C)

Allowable boost pressure

Flange type

■Special specifications

Structure

MaterialMotor

Paint

Shaft seal

Other

ImpellerPower source

Mechanical seal (SiC vs Carbon) (25~100mm)Mechanical seal (SiC vs SiC) (125~200mm)Drain (below casing) (25~100mm)High back pressure (Allowable boost pressure: 1.6MPa) (125~200mm)SUS304 / SCS13 (25~100mm) *1

3-phase 400V classSpecified color for outer surface, salt-resistant paint, heavy-duty salt-resistant paint, Sewage works agency specification

LP(-e)/LPE-e Volute pumps2-pole/4-pole, line-shapedCast-iron

3

0.020.015 0.03 0.04 0.06 0.08 0.10 0.15 0.30.2 0.4 0.6 0.8 1.0 1.51

2

3

4

6

8

10

15

20

30

40

50〈50Hz〉Synchronous rotation speed 3000min-1

■Selection chart●Nominal diameter: 25～100mm


〈50Hz〉Synchronous rotation speed 1500min-1

Discharge rate (m3/min)

A5.08A5.08S

LP32

LP25

LP40 LP50 LP65 LP80

65C55.5-e80C57.5-e

100C57.5-e100C55.5-e

80C55.5-e

A5.04S

A5.05S

B51.5-e

B51.5-e

B53.7-e

B52.2-e

B53.7-e

B52.2-e

B51.5-e

B52.2-e

B53.7-e

A5.75-e

A5.75-eA5.25-eA5.25S

A5.25-eA5.25S

A5.75-e

A5.75-e

A5.4-eA5.4S

A5.4-eA5.4S

A5.4-eA5.4S

40B52.2-e

40B51.5-e

A5.15SA5.15

A5.25-eA5.25S

Tota

l hea

d (m

)To

tal h

ead

(m)

Discharge rate (m3/min)

K522-eK511-e

K57.5-e

K511-e

J515-e

J518-e

G522-e

G530-e

F575-e

F555-e

G537-e

FC555-eFC545-eF545-e

GC537-eJ530-eJ522-eJC522-eK518-e

KC518-e

K530-e

J537-e

J518-e

J545-e

J555-e

J575-e

K515-e

5

0.5 1.0 2.0 4.03.0 5.0 10 20

10

20

30

40

50

100 558861

LPE125-e LPE150-e LPE200-eLP200-e


4

■Net Positive Suction Head Required (NPSHR): Bore diameter 125~200mm●Nominal diameter: 125mm



* LP200J: NPSHR is 5m. However, if the pump is used with the total head of 10m or less, NPSHR should not exceed 60% of the total head.

0.0

1.0

2.0

3.0

4.0

5.0

6.0

0.0 1.0 2.0 3.0 4.0

NP

SH

R(m

)

Flow rate (m3/min)

Flow rate (m3/min)

0.0

2.0

4.0

6.0

8.0

10.0

12.0

0.0 2.0 4.0 6.0 8.0 10.0 12.0

LPE125J

LPE125G

LPE125K

LPE200K

Flow rate (m3/min)

NP

SH

R(m

)

0.0

2.0

4.0

6.0

8.0

0.0 2.0 4.0 6.0 8.0

LPE150G(C)LPE150J(C)LPE150K[15kW or less]

LPE150K(C)[18.5kW]

LPE150F(C)

NP

SH

R(m

)


5

LP25A5.04SLP25A5.05SLP25A5.08S

0.040.050.080.150.250.250.40.250.40.4

0.0150.020.02

4.35.75.2

0.030.030.035

2.84.74.7

0.040.040.05

1.53.64.3

0.10.10.125

LP25A5.15S 0.025 9.5 0.05 7 0.07 4.5 0.2LP25A5.25S 0.02 13.5 0.04 11.5 0.06 8.5 0.2LP32A5.25S 0.05 9.5 0.09 8 0.125 6 0.39

32LP32A5.4S 0.05 14.2 0.09 12.5 0.125 10.5 0.39LP40A5.25S 0.10 7 0.16 5.5 0.20 4.5 0.39

40LP40A5.4S 0.10 10 0.16 8.5 0.20 7.5 0.39

50 LP50A5.4S 0.16 8 0.25 5.5 0.32 3.5 0.39

25

32

40

50

65

80

100

LP25A5.08LP25A5.15LP25A5.25-eLP32A5.25-eLP32A5.4-eLP32A5.75-eLP40A5.25-eLP40A5.4-eLP40A5.75-eLP40B51.5-eLP40B52.2-eLP50A5.4-eLP50A5.75-eLP50B5.15-eLP50B52.2-eLP50B53.7-eLP65A5.75-eLP65B51.5-eLP65B52.2-eLP65B53.7-eLP65C55.5-eLP80B51.5-eLP80B52.2-eLP80B53.7-eLP80C55.5-eLP80C57.5-eLP100C55.5-eLP100C57.5-e

0.08 0.02 5.2 0.035 4.7 0.05 4.3 0.10.15 0.025 9.5 0.05 7 0.07 4.5 0.20.25 0.02 13.5 0.04 11.5 0.06 8.5 0.20.25 0.05 9.5 0.09 8 0.125 6 0.390.4 0.05 14.2 0.09 12.5 0.125 10.5 0.390.75 0.05 19 0.09 17 0.125 15 0.390.25 0.10 7 0.16 5.5 0.20 4.5 0.390.4 0.10 10 0.16 8.5 0.20 7.5 0.390.75 0.10 16 0.16 14 0.20 13 0.391.5 0.05 28 0.10 27 0.20 23 0.592.2 0.05 37 0.10 36.5 0.20 32.5 0.590.4 0.16 8 0.25 5.5 0.32 3.5 0.390.75 0.16 13 0.25 10.5 0.32 7.5 0.391.5 0.16 21 0.25 19.5 0.32 17 0.592.2 0.16 29.5 0.25 27 0.32 24.5 0.593.7 0.16 41 0.25 39 0.32 36.5 0.540.75 0.25 10 0.40 7.5 0.50 5 0.391.5 0.25 15.5 0.40 13.5 0.60 9.5 0.592.2 0.25 22 0.40 19 0.60 14 0.593.7 0.25 32 0.40 28.5 0.60 21.5 0.595.5 0.25 45 0.40 40 0.50 36 0.391.5 0.40 12.5 0.60 10.5 1.05 4 0.592.2 0.40 15 0.60 13.5 1.20 5.5 0.593.7 0.40 21.5 0.60 19.5 1.20 12.5 0.595.5 0.40 32.5 0.60 29 0.80 24 0.397.5 0.40 42 0.60 37 0.80 30 0.395.5 0.63 23 1.0 20 1.25 17 0.397.5 0.63 33 1.0 27 1.25 21.5 0.39

125

150

200

LPE125K-57.5-eLPE125K-511-eLPE125J-515-eLPE125J-518-eLPE125G-522-eLPE125G-530-eLPE150K-511-eLPE150K-515-eLPE150K-518-eLPE150KC-518-eLPE150J-518-eLPE150J-522-eLPE150JC-522-eLPE150J-530-eLPE150G-537-eLPE150GC-537-eLPE150F-545-eLPE150FC-545-eLPE150F-555-eLPE150FC-555-eLPE150F-575-eLPE200K-522-eLPE200K-530-eLP200J-537-eLP200J-545-eLP200J-555-eLP200J-575-e

7.5 11 15 18.5 22 30 11 15 18.5 18.5 18.5 22 22 30 37 37 45 45 55 55 75 22 30 37 45 55 75

0.80.80.80.80.80.81.61.61.61.61.61.61.61.61.61.61.6 1.6 1.6 1.6 1.6 3.23.23.23.23.23.2

17.823.527.830.836.747.617.322.623.121.426.130.729.333.840.138.245.2 40.9 54.4 49.0 66.7 20.823.628.431.836.543.0

2.02.02.02.02.02.03.23.23.23.23.23.23.23.23.23.23.2 4.0 3.2 4.0 4.0 6.46.46.46.46.46.4

15.721.325.828.835.345.610.219.321.119.522.927.326.030.038.636.844.9 39.4 54.4 47.3 63.8 16.421.323.227.132.440.4

3.03.23.33.53.53.55.05.64.56.05.04.05.56.05.06.04.86.04.86.47.09.0

10.09.0

10.010.010.0

10.114.320.022.830.039.5

8.611.019.613.817.125.518.223.234.629.842.034.951.140.052.010.011.717.719.124.331.8

1.181.131.091.061.000.891.191.141.141.161.111.061.081.020.980.990.940.980.840.890.721.161.131.041.010.960.91

Type

SpecificationsPhase

Allowable boostpressure

MPaTotal head

mDischarge rate

m3/minTotal head

mDischarge rate

m3/minTotal head

mDischarge rate

m3/min

Nominaldiameter

mm

OutputkW

■Specification table

Single-phase

3-Phase

Type

Specifications Allowable boostpressure

MPaTotal head

mDischarge rate

m3/minTotal head

mDischarge rate

m3/minTotal head

mDischarge rate

m3/min

Nominaldiametermm

OutputkW


6

PhaseVoltage

VCurrent

ARotation speed

min-1TypeOutput

kWThermal

class

Classification Rating

Torque%

CurrentA

Method

Starting

Load side(D.S)

Anti-load side(O.S)

Bearing

Singlephase

Drip-proofprotected type

Totally enclosedself-cooling

outdoor type

Totally enclosed self-cooling outdoor type

Drip-proof protected type

Totally enclosedfan-cooled outdoor

type

3-phase

0.040.050.080.150.250.40.080.150.250.40.751.52.23.75.57.5

1.0 1.3 1.9 2.9 4.5 6.1 0.6 1 1.2 1.7 3.2 5.9 8.414.9 22 28.4

2870279028652750294028502885278029102870288028952880293029302920

98.1 77.2 81.9 53.2 85 51 486.5 370.5 460 379 311 312 400 319 235 242

3.6 3.6 6.6 8.3 33.4 33.4 3.4 4.8 10.5 14.2 26.8 49.3 81.4 143 182 234

Capacitor

Capacitor

Capacitor

Capacitor

Capacitor

Capacitor

Direct-on-Line start










FFFEEEFEFFFBBBBB

6201UUC36201UUC36201UUC36200DDU6204ZZC36204ZZC36201UUC36200DDU6204ZZC3E6204ZZC3E6205ZZC3E6306ZZC3E6306ZZC3E6307ZZC3E6308ZZC3E6308ZZC3E

6201UUC36201UUC36201UUC36200DDU6203ZZC36203ZZC36201UUC36200DDU6203ZZC3E6203ZZC3E6204ZZC3E6205ZZC3E6205ZZC3E6306ZZC3E6306ZZC3E6306ZZC3E

100100100100100100200200200200200200200200200200

■Motor specification table●Nominal diameter: 25～100mm

3-phaseTotally enclosed

fan-cooled outdoortype

7.5111518.522303745557590

29.043.558.069.083.0

109140168202276330

14651470147014701470147014701470147514751475

315370364294325295343324317263255

260366480576673919

12111435180024012720












FFFFFFFFFFF

6308ZZC36309ZZC36309ZZC36311ZZC36311ZZC36312ZZC36313ZZC36313ZZC36314ZZC36317ZZC36317ZZC3

6306ZZC36309ZZC36309ZZC36311ZZC36311ZZC36311ZZC36312ZZC36312ZZC36313ZZC36314ZZC36314ZZC3

200V200V200V200V200V200V200V200V200V200V200V

* Urea grease is used for bearings.* Piping connection dimensions are the same as those of a conventional pump (product equipped with IE1 motor). The motor is also compatible, therefore, it is possible to replace with the Top Runner (equivalent to IE3) motor. However, pay attention to the following.①The rotation speed of the motor tends to increase because of its characteristics. The current may exceed the rated current value. Adjust the flow rate to use the motor in a range which does not exceed the rated current value.②Some motor dimensions have been changed from conventional ones. Confirm with the dimension table for details.

* Urea grease is used for the bearing. However, lithium grease is used for 0.15kW.


PhaseVoltage

VCurrent

ARotation speed

min-1TypeOutput

kWThermal

class

Classification Rating

Torque%

CurrentA

Method

Starting

Load side(D.S)

Anti-load side(O.S)

Bearing


7

LPE125K-57.5-eLPE125K-511-eLPE125J-515-eLPE125J-518-eLPE125G-522-eLPE125G-530-eLPE150K-511-eLPE150K-515-eLPE150K-518-eLPE150KC-518-eLPE150J-518-eLPE150J-522-eLPE150JC-522-eLPE150J-530-eLPE150G-537-eLPE150GC-537-eLPE150F-545-eLPE150FC-545-eLPE150F-555-eLPE150FC-555-eLPE150F-575-eLPE200K-522-eLPE200K-530-eLP200J-537-eLP200J-545-eLP200J-555-eLP200J-575-e

0350/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0350/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0550/2100/S/AR1S1/BS0550/2100/S/AR1S1/BS0550/2100/S/AR1S1/BS0550/2100/S/AR1S1/BS0550/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0450/2100/S/AR1S1/BS0650/2100/S/AR1S1/BS0650/2100/S/AR1S1/BS0650/2100/S/AR1S1/BS0650/2100/S/AR1S1/BS

Ｇ130Ｇ130Ｇ130Ｇ130K150K150Ｇ130Ｇ130Ｇ130Ｇ130K150K150K150K150K150K150K160K160K160K160K160K150K150G105G105G105G105

■Component parts list

LP25A5.04SLP25A5.05SLP25A5.08SLP25A5.15SLP25A5.25SLP32A5.25SLP32A5.4SLP40A5.25SLP40A5.4SLP50A5.4SLP25A5.08LP25A5.15LP25A5.25-eLP32A5.25-eLP32A5.4-eLP32A5.75-eLP40A5.25-eLP40A5.4-eLP40A5.75-eLP40B51.5-eLP40B52.2-eLP50A5.4-eLP50A5.75-eLP50B51.5-eLP50B52.2-eLP50B53.7-eLP65A5.75-eLP65B51.5-eLP65B52.2-eLP65B53.7-eLP65C55.5-eLP80B51.5-eLP80B52.2-eLP80B53.7-eLP80C55.5-eLP80C57.5-eLP100C55.5-eLP100C57.5-e

EA-104-9EA-104-9EH-791-PB-8EA560-008H-16H-16H-16H-16H-16H-16

EH-791-PB-8EA560-008H-16H-16H-16H-16H-16H-16H-16H-20HH-20HH-16H-16H-20HH-20HH-20HH-16H-20HH-20HH-20HEA560-25H-20HH-20HH-20HEA560-25EA560-25EA560-25EA560-25

G80G80G95G95G120G120G120G120G120G120G95G95G120G120G120G140G120G120G120K184K184G120G120G140K184K184G120G140G140K184K198G140G140G140K198K198K198K198

TypeO-ring

(for casing)Mechanical seal


TypeO-ring

(for Seal cover)Mechanical seal



8

LP25A5.04SLP25A5.05SLP25A5.08S

0.040.050.08

303042

696995

696985

182182224

102102 99.5

220.5220.5230

134.5134.5139.5

6.06.08.0

TypeOutputkW A D E H

Pump and motor

KA L W

Approx.masskg

Nominaldiameter

d

25

(Unit: mm)■DimensionsNominal diameter: 25mmPhase/voltage: single-phase/100VOutput: 0.15kWApprox. mass: 7.5kg

Nominal diameter: 25mmPhase/voltage: 3-phase/200VOutput: 0.15kWApprox. mass: 6.4kg


●LP25A5.08 ●LP25A5.15■Assembly drawing ■Assembly drawing

φ102

Rp1

KA

66.5

W

L

A

Rp1

105

105

Earth terminal M4

External length 1900

Earth terminal M4

Drain plugG⅛×3 locations

20 20

Rotation direction

Suction Discharge

2×M10

E

H

70

φ102

70

D

2 2

Rp1

99.5

230

42

Rp1

Drain plugG⅛×3 locations

Cable glandApplicable cable diameter φ9～14

20 2085

224

95

2 2

●LP25A5.04S～5.08S ●LP25A5.15S■Assembly drawing ■Assembly drawing

66.5

139.

5

2×M10

6257

.5

18423 23

21 PT1 ScrewPS⅛ DrainPT1 Screw 21

230

φ9290

Power cable 2m

Air vent

211.

541

.5

253

Rotation direction

Suction Discharge

6257

.5

18423 23

PT1 Screw

PS⅛ Drain

PT1 Screw

2121

230

90Cable 0.5ｍ

Air vent

195.

541

.5

237

φ92


9

●LP25A5.25S

●LP32～50A Single phase

■Assembly drawing

■Assembly drawing

Type Output A B D E HNominaldiameter

d

(Unit: mm)■Dimensions

Flange dimensions

Plug ⅜B

Drain plug ⅛B

LP32A5.25S 0.250.40.250.40.4

7070808085

276276278278283

140140150150160

140140150150150

280280300300310

LP32A5.4SLP40A5.25SLP40A5.4SLP50A5.4S

32

40

50

LP32A5.25S 346346358358368

173173171171178

9292919195

8181808083

2827302931

LP32A5.4SLP40A5.25SLP40A5.4SLP50A5.4S

Air vent

Drain plug ⅛BNominal diameter: 25mmPhase/voltage: single-phase/100VOutput: 0.25kWApprox. mass: 19.0kg240

60φ

25

φ25

（89

）

75

φ25

95

2×φ12Rotation direction

81.5

272

332

76.5

158

φ129

120120

φd

φd

A

H

W

W2

W1

B

L

φ129

Air vent

Rotation direction

DE

（89

）

kW

Approx.masskg

Type L W W1 W2

☆Flange dimensions: JIS 10K thin type or equivalent


10

●LP25A5.25-e

■Assembly drawing

Flange dimensions

●LP32～65A-e　0.25～0.75kWLP32A5.25-eLP32A5.4-eLP32A5.75-eLP40A5.25-eLP40A5.4-eLP40A5.75-eLP50A5.4-eLP50A5.75-eLP65A5.75-e

0.250.4

0.750.250.4

0.750.4

0.750.75

707070808080858595

295295304297297306302311318

140140140150150150160160175

140140140150150150150150165

280280280300300300310310340

Type OutputkW A B D E H

Approx.mass

kg

Nominaldiameter

d

32

40

50

65

LP32A5.25-eLP32A5.4-eLP32A5.75-eLP40A5.25-eLP40A5.4-eLP40A5.75-eLP50A5.4-eLP50A5.75-eLP65A5.75-e

217217211219219213224218225

103103111103103111103111111

133133141133133141133141141

365365374377377386387396413

145145163145145163145163163

214214226213213221216224228

252935263035333742

Type LKLKGKA WMD

(Unit: mm)


■Dimensions

■Assembly drawing


２４０１２０１２０Drain plug ⅛B

（６２）

（１

０３

）

Ｇ½

６０

２９

１

３５

１

（２

１３

）

φ１４５

（２

１０

）

φ25

φ25

φ25

７５

２×φ１２

９５

Rotation direction

Air vent

（６２）Ｇ½

（Ｋ

Ｇ）

（Ｋ

Ｌ）（

Ｗ）

φＭＤ

Plug ⅜B

Drain plug ⅛B

Ｈ

ＤＥ

Air vent

Rotation direction

L

B

（K

A）

A

φｄ

φｄ

（１

3３）


11

●LP-B-e

■Assembly drawing

■Assembly drawing

LP40B51.5-eLP40B52.2-eLP50B51.5-eLP50B52.2-eLP50B53.7-eLP65B51.5-eLP65B52.2-eLP65B53.7-eLP80B51.5-eLP80B52.2-eLP80B53.7-e

1.52.21.52.23.71.52.23.71.52.23.7

8080808080959595

100100100

345345350350393358358398360360403

170170155175175175175175200200200

170170155165165165165165190190190

340340310340340340340340390390390

40

50

65

80

LP40B51.5-eLP40B52.2-eLP50B51.5-eLP50B52.2-eLP50B53.7-eLP65B51.5-eLP65B52.2-eLP65B53.7-eLP80B51.5-eLP80B52.2-eLP80B53.7-e

214214219219255227227260229229265

123123123123147123123147123123147

155155155155177155155177155155177

425425430430473453453493460460503

266266243266289251251289254254278

2934313557353961474667


●LP-C-eLP65C55.5-eLP80C55.5-eLP80C57.5-eLP100C55.5-eLP100C57.5-e

5.55.57.55.57.5

95100100115115

458461461460460

185200200225225

185190190205205

370390390430430

65

80

100

LP65C55.5-eLP80C55.5-eLP80C57.5-eLP100C55.5-eLP100C57.5-e

235238238237237

194194194194194

260260260260260

553561561575575

402402402402402

81879894

105


Air vent

ＤＥ

Ｈ

Drain plug ⅛B

ＡＢ

Ｌ

（Ｋ

Ａ）

Plug ⅜B

Rotation direction

Ｇ¾ （６２）

φd

（Ｗ

）

（Ｋ

Ｌ）

（Ｋ

Ｇ）

Ｂ

Ｌ

Ｄ

Ｇ１¼

ＫＡ

Ｅ

Ｈ

Ａ

Plug ⅜B

Rotation direction

Drain plug ⅛B

Air vent



φd

KG

KL

W

φdφd

Type OutputkW

A B D E H

Approx.mass

kg

Nominaldiameter

d

Type KLKGKA WL

Type OutputkW

A B D E HNominaldiameter

d

Type KLKGKA WLApprox.mass

kg


12

MS(Disassembly dimensions)

■Assembly drawing●LPE125～200-e/LP200-e

4×φ FA foundation bolt hole(Recommended foundation bolt FD)

with drain only in case of LPE125G-e, LPE150G-e, LPE150F-e

LPE125K-57.5-eLPE125K-511-eLPE125J-515-eLPE125J-518-eLPE125G-522-eLPE125G-530-eLPE150K-511-eLPE150K-515-eLPE150K(C)-518-eLPE150J-518-eLPE150J(C)-522-eLPE150J-530-eLPE150G(C)-537-eLPE150F(C)-545-eLPE150F(C)-555-eLPE150F-575-eLPE200K-522-eLPE200K-530-eLP200J-537-eLP200J-545-eLP200J-555-eLP200J-575-e

7.51115

18.522301115

18.518.5223037455575223037455575

250250250250250250250250250250250250250250250250295295330330330330

608608608608608608620620620620620620650660690690690690763763763763

215226234251254254231231251260260260258311311311267267277277277277

700700800800800800800800800800800800800

100010001000

900900

1000100010001000

256256276277298306286286286314314314320361361426332332392392452513

1067114211721170117012101154118411831183118312221388139814321568125312921523152315711577

TypeOutput

kW

270323358406453487358377426477486520615702815982467501798794924

1050

A B H KG KL L

G1G1 ½G1 ½G2G2G2

G1 ½G1 ½G2G2G2G2

G2 ½G2 ½G2 ½G3G2G2G2G2G2G3

MB

90120120120120120120120120120120120150150150150120120150150150150

MS

471482510528552560517517537574574574578672672737599599669669729790

W

360360360360360360430430430430430430430500500500500500500500500500

BL

300300300300300300350350350350350350350410410410410410410410410410

BP

32323232323232323232323232505050323235353535

BH

23232323232323232323232323252525252525252525

FA

M20M20M20M20M20M20M20M20M20M20M20M20M20M22M22M22M22M22M22M22M22M22

FDNominaldiameter

d

125

150

200

(Unit: mm)■DimensionsApprox.mass

kg

Air vent

Rotation direction

BL Plug ⅜B

Plug ⅜B

Drain plug ⅜B

Drain plug ⅜B

BLH

BP BP

Air vent plug

MB

Air vent

（K

L）

（W

）

KG

LB

BH

Aφ

d

φd


13

7

9

10

11

58 6 4 3 1

2

No. Part name Qty Material

1 Casing

Frame

Impeller

Impeller nut

Liner ring

Key

O-ring

Mechanical seal

Air vent valve

Deflector

Motor

1 FC200

2 1 FC200

3 1 CAC406

4 1 SUS304

5 1 CAC406

6 1 SUS420J2

7 1 NBR

8 1 Ceramic vs Carbon

9 2 C3604BD

10 1 CR

11 1

●LP40～50A Single phase

■Example of sectional drawing ■Parts list

Applicable models: LP40A5.25S / LP40A5.4S / LP50A5.4S


1

2

3

4

5

6

7

8

9

10

11

12

13

14

Casing

Frame

Impeller

Impeller nut

Liner ring

Key

Deflector

Mechanical seal

O-ring

Plug

Air vent valve

Drain plug

Motor shaft *1

Motor

1

1

1

1

1

1

1

1

1

2

2

1

1

1

FC200

FC200

CAC406

SUS304

CAC406

SUS304

CR

Ceramic vs Carbon

NBR

SWCH

C3604BD

SWCH

SUS304+S35C

–

●LP40～80B-e 1.5kW

■Example of sectional drawing ■Parts list

Applicable models: LP40B-51.5-e / LP50B-51.5-e LP65B-51.5-e / LP80B-51.5-e1* The indicated materials are equivalent products.

５４

８１１

７

１

２

３６

９

１３

１４

１２

１０


14

●Pressure gauge / compound gaugePlan to attach a pressure gauge/compound gauge to the piping side.

○

●LPE-e (Excluding 200J)


■Example of sectional drawing


1

2

3

4

5

6

7

8

9

Casing

Frame

Seal cover

Impeller

Main shaft

Liner ring

Mechanical seal

O-ring

O-ring

1

1

1

1

1

2

1

1

1

FCD450

FCD450

FCD450

SCS13

SUS420J2

CAC406

SiC vs Carbon

NBR

NBR

■Parts list

●Nominal diameter: 125～200mm■Installation method


10

11

12

13

14

15

16

17

Coupling

Coupling cover

Parallel pin

Air vent valve

Air vent plug

Plug

Drain plug

Motor

1

2

1

1

2

2

2*

1

FCD450

SUS304

S45C

C3771B

C3604BD

SWCH

SWCH

─

Applicable models: LPE125-e / LPE150-e / LPE200-e* 3 drain plugs for LPE125G-e,LPE150G-e and LPE150F-e.

○ ×

× ○Other installation methods are unsupported.

172

11

13

3

14

7

4

15

1

16

10

12

5

8

9

6


15

,　

TERAL INC.Head Office 230, Moriwake, Miyuki-cyo, Fukuyama-city, Hiroshima, 720-0003, Japan

Tel.+81-84-955-1111 Fax.+81-84-955-5777www.teral.net

Teral Asia LimitedRoom 1001,10/F, Olympia Plaza, 255 King's Road, North Point, Hong Kong

Tel.+852-2571-0935 Fax.+852-2571-0619

TERAL THAI CO.,LTD.150 Moo 16 Udomsorayuth Rd., T.Bangkrasan, A.Bangpa-In, Ayutthaya 13160 Thailand

Tel.+66-3535-2148-9 Fax.+66-3535-2150

TERAL TRADING & SERVICE CO.,LTD. 150 Moo 16 Udomsorayuth Rd., T.Bangkrasan, A.Bangpa-In, Ayutthaya 13160 Thailand

Tel.+66-3535-2145-7 Fax.+66-3535-8549

Teral Malaysia Sdn.Bhd. 10, Jalan SS13/6A, Subang Jaya Industrial Estate, 47500, Subang Jaya, Selangor D.E, Malaysia

Tel.+60-3-5611 5775 Fax.+60-3-5612 5775

PT.Teral Indonesia Pumps and Fans Jalan BSD Sektor XI Taman Tekno, Block G3 No.8, Setu Tangerang Selatan, Banten, Indonesia 15314

Tel.+62-21-29665778 Fax.+62-21-75673913

Teral Vietnam Limited Liability Company Room 1306, 13th Floor, BIDV Tower, 194 Tran Quang Khai Street, Ly Thai To Ward, Hoan Kiem District, Hanoi, Vietnam

Tel.+84-24-3935-2790 Fax.+84-24-3935-2800

Teral General Machine (Shanghai) Co.,Ltd. No.285, Yuan Qu Road(N), Bei Qiao, Min Hang District, Shanghai 201109, China

Tel.+86-21-6490-9128 Fax.+86-21-6490-9126

Teral-Aerotech Fans Private Ltd. Plot No.188-189, Ecotech Extension-1, Surajpur Kasna Road, Greater Noida-201306, Uttar Pradesh, India

Tel.+91-9810162210, +91-9310162210

Teral Middle East F.Z.C. 1806-002, 18th floor, BB1, Mazaya Business Avenue, JLT, Dubai, UAE. PO Box 414781

Tel.+971-4369 9039

Teral Pumps & Fans North America Ltd. Suite # 197, 800-15355 24 Ave Surrey, B.C., CANADA V4A 2H9

Tel.+1-604-839-1008

2017 01

E-CAT5-P-LPeLP-00-A

in-line pumps lp(-e)/lpe-e - teral.info · suction total head (suction height + suction piping...

Documents