i. rationale for regulation country rationale for...

as of 3 November 2017

of 17

I. COUNTRIES WITH MANDATORY STANDARDS FOR GOVERNMENT PROCUREMENT ONLY

INDONESIA

I. RATIONALE FOR REGULATION

COUNTRY RATIONALE FOR REGULATION

Indonesia Consumer Protection

II. REGULATION BODY

COUNTRY REGULATORY BODY

Indonesia

Ministry of Industry Ministry of Energy and Mineral Resources Ministry of Trade


of 17

III. LEGISLATIVE FRAMEWORK

COUNTRY LEGISLATIVE FRAMEWORK

Indonesia 1. Act No. 8 / 1999 concerning Consumer Protection

2. Act No. 3 / 2014 concerning Industry

3. Act No. 7 / 2014 concerning Trade

4. Act No. 20 /2014 concerning Standardization and Conformity Assessment

5. Government Regulation No. 102/2000 concerning National Standardization

6. Decree of the Minister of Industry No. 86/M-IND/PER/9/2009 concerning the Implementation of

SNI in Industrial Sector

7. Decree of the Minister of Industry No. 51/M-IND/PER/3/2012 concerning The Procedures for

Recognition of Certification Product of Electrical and Electronic Equipment Issued by

Conformity Assessment Bodies Listed in ASEAN

8. Decree of the Minister of Energy and Mineral Resorces No. 01/2016 concerning The

Procedures for Recognition of Product Certification and Product Test Report of Electrical and

Electronic Equipment Issued by Conformity Assessment Bodies Listed in ASEAN

9. Decree of the Minister of Trade No. 24/M-DAG/PER/4/2016 concerning Standardization on

Trade Sector


of 17

IV. MANDATORY STANDARDS

Product type or grouping

STANDARDS

State reason if MOD

Indicate

whether

requires:

Safety (S),

Environment

(E), EMC,

or combinatio

n

HS Code Type of

Certification Domestic Standards

Please tick box if

mandatory

Relevant International Standards

Extent of Alignment

Incandescent lamps

SNI 04-3560-1994 V IEC 60064 Ed.6 (1993-12)

IDT S 5

Self-ballast lamp for general lighting service

SNI 04-6504-2001 V IEC 60968 Ed.1.0 (1988-11)

IDT S 8539.31.30 5

Plugs and socket-outlets for household and similar purposes. Part 1 : General requirement

SNI 04-3892.1-2006 V IEC 60884-1 (2002-06)

IDT S 8536.69.92 8536.69.99

5

Switches for household installations and similar fixed electric. Part 1: General requirements

SNI 04-6203.1-2006 V IEC 60669-1 (2000)

IDT S 8536.50.61 8536.50.69 8536.50.99

5

Circuit breakers for over current protection for household and similar installation. Part 1 : Circuit breaker for a.c operated

SNI 04-6507.1-2002

SNI 04-6507.1-2002/Amd1. 2006

V IEC 60898-1 (2003)

IDT S 8536.20.91 8536.20.99

5

Electrical appliances for household usages and other similar types of safety products; Part 2-80. Special requirements for electric fan

SNI 04-6292.2.80-2006

V IEC 60335-2-80(2004-03)

IDT S 8414.51.10 8414.51.91 8414.51.99

5

Lamp controlgears - Part 1: General and safety requirements

SNI 04-6959.1-2003

V IEC 61347-1 (2000-10) IDT

S 8504.10.00 5

Lamp controlgears - Part 2-3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps

SNI 04-6959.2.3-2003

V IEC 61347-2-3 (2000-10) IDT

S 8504.10.00 5


of 17


STANDARDS

State reason if MOD

Indicate

whether

requires:

Safety (S),

Environment

(E), EMC, or

combination

HS Code Type of


Please tick box if

mandatory


Extent of Alignment

Residual current operated circuit - breakers without integral overcurrent protection for household and similar uses (RCCB) - Part 1: General rules

SNI 04-6956.1-2003 V IEC 61008-1 (1996-12) IDT S 8536.20.91 8536.20.99

5

Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB’s) - Part 2-1: Applicability of the general rules to RCCB’s functionally independent of line voltage

SNI 04-6956.2.1-2005

V IEC 61008-2-1 (1990-12) IDT S 8536.20.91 8536.20.99

5

Luminaires - Part 1: General requirements and tests

SNI 4 -6973.1-2005 V IEC 60598-1 (2003)

IDT

S 9405.10.30 9405.10.40 9405.10.90

5

Luminaires - Part 2-1: Particular requirements - Fixed general purpose luminaires

SNI 4 -6973.2.1-2005

V IEC 60598-2-1 (1979) IDT

S 9405.10.30 9405.10.40 9405.10.90

5

Luminaires - Part 2-2: Particular requirements - Recessed luminaires

SNI 4 -6973.2.2-2005

V IEC 60598-2-2 (1997)

IDT

S 9405.10.30 9405.10.40 9405.10.90

5

Luminaires - Part 2-3: Particular requirements - Luminaires for road and street lighting

SNI 4 -6973.2.3-2005

V IEC 60598-2-3 (2002) IDT

S 9405.40.50 5

Luminaires - Part 2-5: Particular requirements – Floodlights

SNI 4 -6973.2.5-2005

V IEC 60598-2-5 (1998): IDT

S 9405.10.30 9405.40.20 9405.40.40

5

Primary Battery - part 1: General SNI 04-2051.1-2004 V

IEC 60086-1 (2000)

IDT

S 8506.10.10 8506.10.90 8506.50.00 8506.80.10 8506.80.20

5


of 17


STANDARDS

State reason if MOD

Indicate

whether

requires:

Safety (S),

Environment

(E), EMC, or

combination

HS Code Type of


Please tick box if

mandatory


Extent of Alignment

Primary Battery - part 2: Electrical and Physical Requirement

SNI 04-2051.2-2004 V IEC 60086-2 (2000)

IDT

S 8506.10.10 8506.10.90 8506.50.00 8506.80.10 8506.80.20

5

PVC insulated cables with a rated voltage up to 450/750 V - Part 3: Non-sheated cables for fixed wiring

SNI 04-6629.3-2006 V IEC 60227-3(1997-11) IDT

S 8544.11.20 8544.11.30 8544.11.40 8544.11.90 8544.49.22

5

PVC insulated cables with a rated voltage up to 450/750 V - Part 4: Sheated cables for fixed wiring

SNI 04-6629.4-2006 V IEC 60227-4(1997-12) IDT

S 8544.11.20 8544.11.30 8544.11.40 8544.11.90 8544.42.94 8544.42.95 8544.42.96 8544.42.97 8544.49.22

5

PVC insulated cables with a rated voltage up to 450/750 V - Part 5: Flexible cables

SNI 04-6629.5-2006 V IEC 60227-5(2003-07) IDT

S 8544.11.20 8544.11.30 8544.11.40 8544.11.90 8544.42.94 8544.42.95 8544.42.96 8544.42.97 8544.49.22 8544.49.23 8544.49.41

5


of 17


STANDARDS

State reason if MOD

Indicate

whether

requires:

Safety (S),

Environment

(E), EMC, or

combination

HS Code Type of


Please tick box if

mandatory


Extent of Alignment

Safety of household and similar electrical appliances — Part 2-41 : Particular requirements for pumps

SNI 04-6292.2.41-2003

V IEC 60335-2-41 (2002-10)

IDT

S 8413.70.42 8413.70.91 8413.81.13

5

Household and similar electrical appliances – Safety – Part 2-3: Particular requirements for electric irons

SNI 04-6292.2.3-2003

V IEC 60335-2-3 (2002-03)

IDT

S 8516.40.90 5

Audio, video and similar electronic apparatus —Safety requirements

SNI 04-6253-2003 V IEC 60065 (2001–12) MOD 4.1.3 Unless otherwise specified, the tests are carried out under normal operating conditions at: - anambient temperature between 20 oC and 35 oC

- a relative humidity of 70 % ± 15% maximum

S 8528.72.91 5

Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

SNI IEC 60335-2-40:2009

V IEC 60335-2-40 Ed 4.2 (2005-07)

IDT

S 8415.10.10 5


of 17


STANDARDS

State reason if MOD

Indicate

whether

requires:

Safety (S),

Environment

(E), EMC, or

combination

HS Code Type of


Please tick box if

mandatory


Extent of Alignment

Household and similar electrical appliances - Safety - Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers

SNI IEC 60335-2-24:2009

V IEC 60335-2-24 Ed 6.1 (2005-04)

IDT

S 8418.10.11 8418.10.19 8418.21.10 8418.21.90 8418.29.00 8418.30.10 8418.30.90 8418.40.10 8418.40.90

5

Household and similar electrical appliances - Safety - Part 2-7: Particular requirements for washing machines

SNI IEC 60335-2-7:2009

V IEC 60335-2-7 (2004-11)

IDT

S 8450.11.10 8450.11.90 8450.12.10 8450.12.90 8450.19.11 8450.19.19

5


of 17

V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

COUNTRY TYPES OF CON-FORMITY ASSESS-

MENT REGIMES

MODE OF REGULATION

Indonesia Technical Regulation based on SNI

Technical regulation on EEE by adopting partially or fully technical specification and/or parameter of SNI is stipulated by Ministerial Decree taking into account safety, security, health, environment, moral hazard, and economical aspects, that are equally imposed to both domestic and imported products which are traded in Indonesian teritory.

Manufacturers of EEE which are technically regulated based on SNI shall fulfill the SNI requirements and shall affix the SNI mark on the products, packages and/or label of their products

Product Registration to get NPB (for imported products) or NRP (for domestic products)

Pre-market surveillance over traded goods produced domestically, shall be done through Product Registration Number (Nomor Registrasi Produk - NRP)

Pre-market surveillance over imported of EEE shall be done through Goods Registration Number (Nomor Pendaftaran Barang – NPB),

NRP and NPB shall be issued by the Director of Standardization and Quality Control, Ministry of Trade

The validity of NRP and NPB are in accordance with the validity period of SPPT SNI.

NRP or NPB shall affix underneath SNI Mark and/or other recognized conformity mark, on to their products or packages.


of 17

COUNTRY TYPES OF CON-FORMITY ASSESS-

MENT REGIMES

MODE OF REGULATION

Registration of CAB CAB issuing an SNI Mark Product Certification can be a domestic or foreign product certification body supported by accredited testing laboratories and/or inspection institutions.

Domestic CAB shall be accredited by KAN according to its scopes, CAB shall be

registered to the Directorate of Standardisation and Quality Control, Ministry of Trade.

All CAB which have the scope of mandatory SNI’s requirements shall be accredited by National Accreditation Body of Indonesia (KAN) and assigned by Minister of Industry


of 17

VI. FLOWCHART OF INDONESIA’S REGIME

PROCEDURES FOR RECOGNITION OF CERTIFICATES OF EEE FROM CONFORMITY ASSESSMENT BODIES IN ASEAN

COUNTRIES

AMS Indonesia

Listed Product Certification Body for EEE

Listed Testing Lab. for EEE

Product Certification Body

SPPT SNI according to certification type ISO/IEC 17067

Product EEE ASEAN

Legend: 1. Using Certificate of Conformity issued by AMS Listed Product Certification Body

2. Using Testing report issued by AMS Listed Testing Lab. Listed Testing lab have to be accredited for full parameter of the standards

3. Direct to Indonesia Registered Product Certification Body

3

1

2


of 17

EEE products from ASEAN countries could enter Indonesia through three mechanisms:

1. Using Certificate of Conformity (CoC) from Product CB outside Indonesia

1.1 Manufacturer certify their products in CB from outside Indonesia (Listed in ASEAN).

1.2 Importer submits an application to Registered CB in Indonesia to issue SPPT-SNI, by attaching required documents.

1.3 CB in Indonesia verifies the application and the documents.

1.4 In the case of questionable data/information in CoC and/or test report, CB in Indonesia may re-test the product.

1.5 In the case of different edition of referenced standard, modification, or others, CB in Indonesia may take test of untested

parameters.

1.6 Based on verification result, CB in Indonesia may approve or reject the application.

1.7 CB in Indonesia will conduct market surveillance

1.8 CB in Indonesia will evaluate factory surveillance report conducted by foreign CB which issued CoC.

2. Using test report from testing laboratory in home country

2.1 Manufacturer test their product in Testing laboratory in their home country (Listed in ASEAN)

2.2 Importer submits an application to Registered CB in Indonesia to issue SPPT-SNI, by attaching required documents.

2.3 CB in Indonesia verifies the application and the documents.

2.4 In the case of questionable data/information in test report, CB in Indonesia may re-test the product.

2.5 In the case of different edition of referenced standard, modification, or others, CB in Indonesia may take test of untested

parameters.

2.6 Based on verification result, CB in Indonesia may approve or reject the application.

2.7 In the case of the application is approved, CB in Indonesia will continue the certification process (including factory audit) and

issues SPPT-SNI or reject the application.

2.8 CB in Indonesia will conduct market surveillance.


of 17

3. Using Indonesia Registered Product CB

Manufacturer certify their products using Indonesia Registered Product CB.

VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

Country Mains

Voltage and Tolerance

Mains Frequency and Tolerance

Applicable Legislation

Mains Plug Configuration

Domestic Standard

Please tick box if mandatory

Relevant International Standard

Extent of Alignment -

Diagram of Mains Plug Configuration-

Indonesia 230 5% 50 5% SNI 04-3892.1-2006 Plugs and socket-outlets for household and similar purposes. Part 1 : General requirement

V

IEC 60884-1

Ed.3.0(2002,am.1(2006)

IEC 60884-2-1 Ed.1.0(1987)

IEC 60884-2-3 Ed.1.0(1989) (0nly for the

safety)

SNI 04-3892.2.3-

2000:Plugs and Sockets-Outlets for household and similar purposes;Part 2.3:Particular Requirement for switched socket outlets without interlock for fixed installation.


of 17

Country Mains Voltage and Tolerance

Mains Frequency and Tolerance

Applicable Legislation

Mains Plug Configuration

Domestic Standard

Please tick box if mandatory

Relevant International Standard

Extent of Alignment -

Diagram of Mains Plug Configuration-

SNI 04-6202-

2000: Plugs and Sockets-Outlets and couplers for industrial purposes;Part 3: Particular Requirement for plugs, socket outlets, connectors and appliance inlets for use in explosive gas atmospheres.

SNI 04-0225-

2000/Amd1-2006 on Amendment 1 of Indonesian National Standard for General Requirements on Electrical Installation

V IEC 60364 (series)


of 17

VIII. MARKING/LOGO :

Affixing SNI and NRP

Note:

101 : Product Certification Body certifying the products 010 : Factory Location 000001 : Registration Number in Directorate of Standardization and Quality Control


of 17

Affixing SNI and NPB

Note:

101 : Product Certification Body certifying the products 156 : Country of Origin 000001 : Registration Number in Directorate of Standardization and Quality Control


of 17

IX. OTHER INFORMATION

No Product Additional Requirement Link for Technical Regulation

1.

Air Conditioner (AC)

- Minimum class I Insulation - Supply cable must SNI certified

http://pustan.kemenperin.go.id/public/default/file_juknis/No_30_IUBTT_2013%20AC%20kulkas%20mesin%20cuci.pdf

2. Refrigerator

- Minimum class I Insulation - Supply cable must SNI certified - Plug must SNI certified - Gross capacity is calculated

based on SNI ISO 15502:2008

3. Washing Machine

- Minimum class I Insulation - Supply cable must SNI certified - Plug must SNI certified - Loading capacity is calculated

based on IEC 60456

4. Water Pump

- Minimum class I Insulation - Supply cable must SNI certified - Plug must SNI certified

http://pustan.kemenperin.go.id/public/default/file_juknis/Juknis_SNI_04-6292.2.3-2003%202.pdf

5. Electric iron

- Minimum class I Insulation - Supply cable must SNI certified - Plug must must SNI certified

6. CRT Television - Minimum class II Insulation - Supply cable must SNI certified - Plug must SNI certified






of 17

X. CONTACT PERSON

Country JSC EEE

Indonesia Representative Officer Chandrini M. Dewi Director of Standardization and Quality Control Directorate General of Consumer Protection and Trade Compliance Ministry of Trade Jl. Raya Bogor KM 26 Ciracas - Jakarta Timur Telp : (021) 8710321/3Fax : 62-21-3863928 E-mail : [email protected], [email protected] Contact Person Konny Sagala, S.Si Head of Center for Cooperation on Standardization - BSN BPPT I Building Jl. M.H. Thamrin No. 8, Kebon Sirih Jakarta Pusat 10340 Indonesia Phone : 62-21-3927422 Fax : 62-21-3927527 E-mail : [email protected], [email protected] Designating Body Wahyu Purbowasito Setyo Waskito Head of Center for Standard Application System - BSN BPPT I Building Jl. M.H. Thamrin No. 8, Kebon Sirih Jakarta Pusat 10340 Indonesia Phone : 62-21-3927422 Fax : 62-21-3927527 E-mail : [email protected]

mailto:[email protected]




i. rationale for regulation country rationale for...

Documents