hydraulic crimping tools and hydraulic presshead general features hydraulic press-head complete with

Download HYDRAULIC CRIMPING TOOLS AND HYDRAULIC PRESSHEAD general features Hydraulic press-head complete with

Post on 24-Jul-2020

0 views

Category:

Documents

0 download

Embed Size (px)

TRANSCRIPT

  • 123123

    H Y

    D R

    A U

    LI C

    C R

    IM P

    IN G

    T O

    O LS

    A N

    D C

    U T T E R

    S

  • 124

    Lightweight and compact, this tool is ideal for the compres- sion of connectors on over head lines and other general ap- plications.

    Having the benefit of spring loaded handles, the dies can be advanced using only one hand; therefore leaving the other hand free to position the connector.

    For ease of operation and comfort of the operator, the tool head can be fully rotated through 180 degrees.

    The built-in safety valve will by-pass the oil supply when the maximum pressure is reached, and a pressure releasing system can easily be oper- ated at any stage of the compres- sion.

    HYDRAULIC CRIMPING TOOL

    general features

    Crimping force kN

    Weigth kglength width

    D i m e n s i o n s m m

    50 346 130 2,0

    M A I N A P P L I C A T I O N S - m a x s e c t i o n m m 2

    L.V. lugs and splices

    “C” sleeve connectors

    H.V. lugs and splices

    150 35 70

    S T O R A G E

    Type Dimensions mm Weightkg Supplied

    with the tool Purchase separately

    VAL P1* 445x290xh95 1,2 � — *Suitable for storage of the tool and 20 sets of dies.

    The operator can advance the dies using only one hand, leaving the other hand free to position the connector.

    180° rotatable head, to work in the most

    comfortable positionOpenable head, ideal for derivations from running conductors

    Pressure releasing system, that can be operated at any stage.

    Safety valve bypassing the oil supply when the

    maximum pressure is reached

    These tools are supplied without dies. For die selection, please refer to chart on pages 178 to 190

    HT 45-E

    Lightweight and compact, this tool is ideal for the compres- sion of connectors on over head lines and other general ap- plications.

    Having the benefit of spring loaded handles, the dies can be advanced using only one hand; therefore leaving the other hand free to position the connector.

    For ease of operation and comfort of the operator, the tool head can be fully rotated through 180 degrees.

    The built-in safety valve will by-pass the oil supply when the maximum pressure is reached, and a pressure releasing system can easily be oper- ated at any stage of the compres- sion.

    general features

    Crimping force kN

    Weigth kglength width

    D i m e n s i o n s m m

    50 346 130 2,0

    M A I N A P P L I C A T I O N S - m a x s e c t i o n m m 2

    L.V. lugs and splices

    “C” sleeve connectors

    H.V. lugs and splices

    150 35 70

    S T O R A G E

    Type Dimensions mm Weightkg Supplied

    with the tool Purchase separately

    VAL P1* 445x290xh95 1,2 � — *Suitable for storage of the tool and 20 sets of dies.

    HT 45-E

  • 125

    HT 51HT 51

    Crimping force kN

    Max operating pressure

    bar Weight

    kglength width

    D i m e n s i o n s m m

    50 700 196 75 1,6

    S T O R A G E

    Type Dimensions mm Weightkg Supplied

    with the tool Purchase separately

    VAL P1* 445x290xh95 1,2 � — Canvas bag 007 350x105 0,13 — � * Suitable for storage of the tool and 20 sets of dies.

    L.V. lugs and splices

    Insulated terminals

    End sleeves

    “C” sleeve Connectors

    300 120 120 70

    S T O R A G E

    Type Dimensions mm Weightkg Supplied

    with the tool Purchase separately

    VAL P1* 445x290xh95 1,2 � — * Suitable for storage of the tool and 20 sets of dies.

    L.V. lugs and splices

    Insulated terminals

    End sleeves

    “C” sleeve Connectors

    240 120 120 70

    M A I N A P P L I C A T I O N S - m a x s e c t i o n m m 2

    M A I N A P P L I C A T I O N S - m a x s e c t i o n m m 2

    New design two speed hydraulic tool,

    lightweight and com- pact, this tool is ideal for working in confined

    spaces. Having the bene- fit of spring loaded handles,

    the dies can be advanced using only one hand; therefore

    leaving the other hand free to position the connector.

    For ease of operation and comfort of the operator, the tool head can be fully rotated through 180 degrees. The built-in safety valve will by-pass the oil supply when the maximum pressure is reached, and a pressure release system can easily be operated at any stage of the compression.

    Crimping force kN

    Weight kglength width

    D i m e n s i o n s m m

    50 380 130 2,7

    HYDRAULIC CRIMPING TOOL

    general features

    Hydraulic presshead com- plete with quick automatic coupler for

    connection to a hydraulic pump with a working pressure of 700 bar max, (see page 170-174) RH 50 is suitable for installing the same range of con- nectors as HT 51.

    HYDRAULIC PRESSHEAD

    general features

    Hydraulic press- head complete with

    quick automatic coupler for connection to hydraulic pump with working pressure of 700 bar max, (see page 170-174). RHM50 is suit- able for installing the same range of connectors as RH50.

    HYDRAULIC PRESSHEAD

    general features

    M A I N A P P L I C A T I O N S - m a x s e c t i o n m m 2

    S T O R A G E

    Type Dimensions mm Weightkg Supplied

    with the tool Purchase separately

    VAL P1* 445x290xh95 1,2 � — Canvas bag 007 350x105 0,13 — � * Suitable for storage of the tool and 20 sets of dies.

    L.V. lugs and splices

    Insulated terminals

    End sleeves

    300 120 120

    Particularly suitable for high volume bench crimping.

    50 700 210 70 1,6

    Crimping force kN

    Max operating pressure

    bar Weight

    kglength width

    D i m e n s i o n s m m

    These tools are supplied without dies. For die selection, please refer to chart on pages 178 to 190

    HT 51-KV version also available for Power Supply Companies

    RH 50

    RHM 50

    VAL P1* 445x290xh95 1,2 * Suitable for storage of the tool and 20 sets of dies.

    HT 51-KV version also available for Power Supply Companies

    50 700 196 75 1,6

    M A I N A P P L I C A T I O N S - m a x s e c t i o n m m

    M A I N A P P L I C A T I O N S - m a x s e c t i o n m m

    50 700 210 70 1,6

    Weight kg

    50 700 196 75 1,6

    Hydraulic presshead com- plete with quick automatic coupler for with quick automatic coupler for with quick

    connection to a hydraulic pump with a working pressure of 700 bar max, (see page 170-174) RH 50 is suitable for installing the same range of con-

    RH 50

    Hydraulic press- head complete with

    quick automatic coupler for connection to hydraulic pump with working pressure of 700 bar max, (see page 170-174). RHM50 is suit- able for installing the same range of

    general features

    Particularly suitable for high

    50 700 210 70 1,6

    Weight kg

    RHM 50

    50 700 210 70 1,6 50 700 210 70 1,6

  • 126

    Hydraulic presshead complete with quick automatic coupler for connec- tion to a hydraulic pump with a work- ing pressure of 700 bar max, (see page 170-174). This lightweight and self contained head, features a patented closure and release mechanism for the die locking pin. The head is easy to use and is ide- ally suited for crimping in confined spaces. RHU81 is suitable for installing the same range of connectors as HT 81-U.

    HYDRAULIC PRESSHEAD

    general features

    S T O R A G E

    Type Dimensions mm Weightkg Supplied

    with the tool Purchase separately

    Canvas bag 007 350x105 0,13 — �

    H T 8 1 - U a n d R H U 8 1 A C C E S S O R I E S F O R C U T T I N G C O N D U C T O R S

    Die Type Cutting Capacity Conductor Type

    MB2-80U

    MB3-80U

    Ø 16 mm

    This die is suitable to cut steel conductors (R ≤ 160 daN/mm2) having the most common strandings, i.e.:

    19 x 1,2 = Ø est. 6,0 mm 7 x 3,0 = Ø est. 9,0 mm 19 x 2,1 = Ø est. 10,5 mm 19 x 2,3 = Ø est. 11,5 mm

    Suitable to cut aluminium strands of 150 mm2 aluminium-steel conductors, without damage to the steel core

    Cu, Alu, Aldrey and Alu-Steel

    This lightweight and self contained tool, features a patented closure and release mechanism for the die locking pin. A wide range of connectors can be crimped with a small number of die sets due to their unique, double groove styling. Dies for cutting copper, aluminium, aldrey and aluminium-steel, are also available (see table below). The tool features a double speed action: a fast advancing speed for rapid approach of the dies to the connector and a slower more pow- erful speed for crimping. For ease of operation and comfort of the operator the tool head can be fully rotated through 180 degrees.

    The built-in safe- ty valve will by-pass the oil supply when the maximum pressure is reached, and a pressure releasing system can easily be operated at any stage of the compression.

    HYDRAULIC CRIMPING TOOL

    general features

    Crimping force kN

    Weight Kg length width

    D i m e n s i o n s m m

    80 485 141 3,4

    S T O R A G E

    Type Dimensions mm Weightkg Supplied

    with the tool Purchase separately

    VAL P3* 620x380xh135 2,5 � — VAL 75** 270x80xh30 0,15 —

Recommended

View more >