hp switch software - apache welcome pageh20628. · hp switch software hp 3500 hp 3800 hp 2910al hp...

HP Switch Software

HP 3500 HP 3800 HP 2910al HP 2615 HP 2620

HP 3500yl HP 2915

HP 5400zl

HP 6200yl

HP 6600

HP 8200zl

15.10September 2012

Comware CLI Commands in ProVision Software

Common-CLI-Phase-3-Sept-2012.book Sunday, September 9, 2012 6:00 PM

HP Networking

Comware CLI Commands in ProVision Software

HP 3500 HP 3800 HP 2910al HP 2615 HP 2620

HP 3500yl HP 2915

HP 5400zl

HP 6200yl

HP 6600

HP 8200zl

15.10September 2012

Common-CLI-Phase-3-Sept-2012.book Page i Sunday, September 9, 2012 6:00 PM

Hewlett-Packard Company 8000 Foothills Boulevard, m/s 5551 Roseville, California 95747-5551 http://www.hp.com/networking/support

© Copyright 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change with-out notice. All Rights Reserved.

This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Hewlett-Packard.

Publication Number

5998-3593September 2012

Applicable Products

HP 2615 Switches (J9565A) HP 2620 Switches (J9623A, J9624A, J9625A, J9626A, J9627A) HP 2910al Switches (J9145A, J9146A, J9147A J9148A) HP 2915 Switches (J9562A) HP 3500 Switches (J9470A, J9471A, J9472A,

J9473A) HP 3500yl Switches (J8692A, J8693A) HP 3800 Switches (J9573A, J9574A, J9575A, J9576A, J9584A, J9585A, J9586A, J9587A, J9588A) HP 5400zl Switches (J8697A, J8698A, J9447A,

J9448A) HP 6200yl Switch (J8992A) HP 8200zl Switches (J9475A, J8715A/B ) HP 6600 Switches (J9263A, J9264A, J9265A,

J9451A, J9452A)

Trademark Credits

Microsoft, Windows, and Microsoft Windows NT are US registered trademarks of Microsoft Corporation. Java™ is a US trademark of Sun Microsystems, Inc.

Disclaimer

The information contained in this document is subject to change without notice.

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard.

Software End User License Agreement and

Hardware Limited Warranty

For the software end user license agreement and the hardware limited warranty information for HP Networking products, visit www.hp.com/networking/support.

Common-CLI-Phase-3-Sept-2012.book Page iii Sunday, September 9, 2012 6:00 PM

v

Contents

Introduction To the ProVision CLI

Comware Command Support in ProVision Software . . . . . . . . . . . . . 1-1

Listing Display Commands in the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

CLI Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Comparing Comware and ProVision Commands . . . . . . . . . . . . . . . . . 1-3

Using CLI Context Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Empty Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Further CLI Operating Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Display Commands

display arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

display arp detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

display arp detection statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

display arp ip-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

display boot-loader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

display clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

display command-alias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

display counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

display counters rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

display cpu-usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

display cpu-usage history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

display current-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

display current-configuration by-linenum . . . . . . . . . . . . . . . . . . . . . . 2-19

display current-configuration configuration . . . . . . . . . . . . . . . . . . . 2-20

display current-configuration interface . . . . . . . . . . . . . . . . . . . . . . . . 2-21

display debugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23

display default-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25

Common-CLI-Phase-3-Sept-2012.book Page v Sunday, September 9, 2012 6:00 PM

vi

display device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26

display dhcp relay information all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28

display dhcp relay information interface Vlan-interface <vlan-id> . . . 2-29

display dhcp relay statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30

display dhcp-snooping binding database . . . . . . . . . . . . . . . . . . . . . . . 2-34

display dhcp-snooping information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35

display dhcp-snooping [ip ip_address] . . . . . . . . . . . . . . . . . . . . . . . . . 2-36

display dhcp-snooping packet statistics . . . . . . . . . . . . . . . . . . . . . . . . 2-37

display dhcp-snooping trust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38

display diagnostic-information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-40

display dns domain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41

display dns domain dynamic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42

display dns < domain | server > . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43

display dns ipv6 server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45

display dot1x [interface] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47

display dot1x [interface …] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56

display dot1x sessions [interface …] . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56

display dot1x statistics [interface …] . . . . . . . . . . . . . . . . . . . . . . . . . . 2-56

display environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-59

display fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60

display fips status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-61

display garp statistics interface <port_list> . . . . . . . . . . . . . . . . . . . . 2-62

display garp timer interface <port_list> . . . . . . . . . . . . . . . . . . . . . . . 2-63

display gvrp state interface <port_list> vlan <vlan-id> . . . . . . . . . 2-64

display gvrp statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-66

display gvrp status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-67

display gvrp vlan-operation interface interface-type interface-

number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-69

display history-command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-70

Common-CLI-Phase-3-Sept-2012.book Page vi Sunday, September 9, 2012 6:00 PM

vii

display hwtacacs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-71

display igmp group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-73

display igmp group interface vlan-interface <vlan-id> . . . . . . . . . . 2-75

display igmp group interface vlan-interface <vlan-id> static . . . . 2-77

display igmp group interface vlan-interface <vlan-id> verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-78

display igmp group port-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-80

display igmp group static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-83

display igmp group verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-85

display igmp group x.x.x.x static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-86

display igmp group x.x.x.x verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-87

display igmp interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-88

display igmp interface verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-91

display igmp interface vlan-interface <vlan-id> . . . . . . . . . . . . . . . . 2-93

display igmp routing-table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-96

display interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-98

display interface brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-100

display interface brief down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-103

display ip as-path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-105

display ip check source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-106

display ip community-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-108

display ip http . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-109

display ip https . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-110

display ip ip-prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-111

display ipv6 dhcp duid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-112

display ipv6 dhcp relay server-address all . . . . . . . . . . . . . . . . . . . . . 2-113

display ipv6 dhcp relay server-address interface <id> . . . . . . . . . 2-115

display ipv6 dhcp relay statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-117

display ipv6 routing-table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-120

display ipv6 routing-table ipv6-address . . . . . . . . . . . . . . . . . . . . . . . 2-122

Common-CLI-Phase-3-Sept-2012.book Page vii Sunday, September 9, 2012 6:00 PM

viii

display ipv6 routing-table protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-124

display lacp system-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-125

display link-aggregation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-127

display link-aggregation member-port . . . . . . . . . . . . . . . . . . . . . . . . 2-128

display link-aggregation summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-130

display link-aggregation verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-132

display lldp local-information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-135

display lldp local-information global . . . . . . . . . . . . . . . . . . . . . . . . . 2-138

display lldp local-information interface interface-type interface-

number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-139

display lldp neighbor-information brief . . . . . . . . . . . . . . . . . . . . . . . 2-141

display lldp neighbor-information list display lldp neighbor-information list system-name <string> . . . 2-143

display lldp statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-144

display lldp statistics global . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-146

display lldp statistics interface interface-type interface-number . . . . 2-147

display lldp status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-149

display lldp status interface interface-type interface number . . 2-150

display lldp tlv-config interface interface-type interface-number . . . . 2-151

display logfile buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-152

display loopback-detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-155

display mac-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-156

display mac-address aging-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-157

display mac-address multicast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-159

display mac-authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-160

display mac-authentication [interface …] . . . . . . . . . . . . . . . . . . . . . 2-165

display memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-167

display mld group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-169

display mld group interface vlan-interface <vid> . . . . . . . . . . . . . . 2-173

Common-CLI-Phase-3-Sept-2012.book Page viii Sunday, September 9, 2012 6:00 PM

ix

display mld group interface vlan-interface <vid> verbose . . . . . . 2-174

display mld group port-info vlan <vlan-id> display mld group port-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-176

display mld group verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-177

display mld group x:x::x:x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-179

display mld group x:x::x:x verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-181

display mld interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-183

display mld interface verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-184

display mld interface vlan-interface <vid> . . . . . . . . . . . . . . . . . . . . 2-186

display mld interface vlan-interface <vid> verbose . . . . . . . . . . . . 2-187

display mld routing-table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-189

display monitor-link group [group-number | all], . . . . . . . . . . . . . . 2-190

display multicast forwarding-table . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-192

display multicast routing-table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-193

display multicast routing-table static . . . . . . . . . . . . . . . . . . . . . . . . . 2-195

display multicast rpf-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-197

display ospf cumulative . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-198

display ospf interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-201

display ospf lsdb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-204

display ospf peer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-207

display ospf routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-209

display ospf vlink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-211

display ospfv3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-213

display ospfv3 area area-id peer interface interface-type interface

number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-215

display ospfv3 area area-id peer peer-router-id . . . . . . . . . . . . . . 2-216

display ospfv3 area area-id peer verbose . . . . . . . . . . . . . . . . . . . . . 2-219

display ospfv3 interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-221

display ospfv3 lsdb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-225

display ospfv3 lsdb statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-227

Common-CLI-Phase-3-Sept-2012.book Page ix Sunday, September 9, 2012 6:00 PM

x

display ospfv3 peer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-228

display ospfv3 peer peer-router-id . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-230

display ospfv3 peer statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-233

display ospfv3 peer verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-234

display ospfv3 statistic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-237

display ospfv3 vlink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-240

display pim bsr-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-242

display pim control-message counters . . . . . . . . . . . . . . . . . . . . . . . . 2-246

display pim grafts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-247

display pim interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-248

display pim interface verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-250

display pim join-prune . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-254

display pim neighbor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-255

display pim neighbor <ip> verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-257

display pim routing-table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-260

display pim rp-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-261

display poe device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-262

display poe interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-263

display poe interface power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-265

display poe power-usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-267

display poe-power alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-268

display poe-power switch state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-269

display port trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-270

display power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-271

display protocol-vlan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-272

display protocol-vlan interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-273

display public-key local rsa public . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-274

display public-key peer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-276

display radius scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-277

display rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-283

Common-CLI-Phase-3-Sept-2012.book Page x Sunday, September 9, 2012 6:00 PM

xi

display rip interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-284

display rip process-id ip-address mask/mask-length . . . . . . . . . . . 2-285

display rip process-id route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-286

display rip process-id route peer ip-address . . . . . . . . . . . . . . . . . . . 2-287

display rmon statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-288

display route-policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-289

display saved-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-291

display saved-configuration by-linenum . . . . . . . . . . . . . . . . . . . . . . 2-293

display schedule reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-295

display sflow display sflow slot <slot-number> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-296

display snmp-agent community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-298

display snmp-agent group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-299

display snmp-agent local-engineid . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-302

display snmp-agent mib-view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-303

display snmp-agent statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-304

display snmp-agent sys-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-305

display snmp-agent trap-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-306

display snmp-agent usm-user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-308

display ssh client source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-309

display ssh server session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-310

display ssh server-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-311

display ssh server status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-312

display ssl client-policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-314

display ssl server-policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-316

display startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-318

display stp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-319

display stp abnormal-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-322

Common-CLI-Phase-3-Sept-2012.book Page xi Sunday, September 9, 2012 6:00 PM

xii

display stp bpdu-statistics display stp bpdu-statistics interface GigabitEthernet <port-num> display stp bpdu-statistics interface GigabitEthernet <port-num>

instance <instanceNUM, 1-32> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-324

display stp brief display stp instance <instance-id> brief display stp instance <instance-id> interface GigabitEthernet

<interface-id> brief display stp instance <instance-id> interface GigabitEthernet

<interface-id> brief display stp instance <instance-id> interface GigabitEthernet

<interface-id> to GigabitEthernet <interface-id> brief display stp instance <instance-id> slot <slot-id> brief display stp interface GigabitEnterface <port-num> brief display stp interface GigabitEnterface <port-num> to

GigabitEnterface <port-num> brief . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-327

display stp down-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-329

display stp history display stp history slot <slot-number> display stp instance <instance-id> history slot <slot-no> display stp instance <instance-id> history . . . . . . . . . . . . . . . . . . . . 2-330

display stp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-332

display stp instance <instance-id> interface GigabitEthernet 1/0/1/ . 2-332

display stp slot <slot-num> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-332

display stp instance <instanceid> tc display stp instance <instanceid> tc slot <slot-no> display stp tc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-334

display stp region-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-335

display stp root . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-337

display switchover state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-338

display system-failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-340

display this . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-341

display transceiver alarm interface . . . . . . . . . . . . . . . . . . . . . . . . . 2-342

display transceiver diagnosis interface . . . . . . . . . . . . . . . . . . . . . . . 2-347

display transceiver interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-350

Common-CLI-Phase-3-Sept-2012.book Page xii Sunday, September 9, 2012 6:00 PM

xiii

display transceiver manuinfo interface . . . . . . . . . . . . . . . . . . . . . . . 2-353

display user-bind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-355

display vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-356

display vrrp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-357

display vrrp interface <interface-type> vrid <virtual routerid> 2-359

display vrrp statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-360

display vrrp statistics interface <interface-type> vrid <virtual router-

id> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-362

display vrrp verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-363

Fundamental Commands

backup startup-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

clock datetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

clock summer-time one-off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

clock summer-time repeating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

clock timezone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

command accounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

command authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

command-alias enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

command-alias mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

delete <startup-config> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

flow-control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

idle-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

quit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

reset saved-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

restore startup-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

Common-CLI-Phase-3-Sept-2012.book Page xiii Sunday, September 9, 2012 6:00 PM

xiv

schedule reboot at . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

schedule reboot delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21

screen-length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

set authentication password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23

speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24

startup saved-configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

sysname . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26

system-view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27

telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28

telnet ipv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29

telnet server enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30

terminal type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31

tftp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32

tftp ipv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33

undo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-34

Common-CLI-Phase-3-Sept-2012.book Page xiv Sunday, September 9, 2012 6:00 PM

xv

Product Documentation

About Your Switch Manual Set

N o t e For the latest version of all HP switch documentation, including Release Notes covering recently added features, please visit the HP Networking web site at www.hp.com/Networking/support.

Electronic Publications

The latest version of each of the publications listed below is available in PDF format on the HP Networking web site, as described in the Note at the top of this page.

■ Installation and Getting Started Guide—Explains how to prepare for and perform the physical installation and connect the switch to your network.

■ Basic Operation Guide—Describes how to use the switch interfaces and introduces basic operations.

■ Management and Configuration Guide—Describes how to configure, manage, and monitor basic switch operation.

■ Advanced Traffic Management Guide—Explains how to configure traffic management features such as VLANs, MSTP, QoS, and Meshing.

■ Multicast and Routing Guide—Explains how to configure IGMP, PIM, IP routing, and VRRP features.

■ Access Security Guide—Explains how to configure access security fea-tures and user authentication on the switch.

■ IPv6 Configuration Guide—Describes the IPv6 protocol operations that are supported on the switch.

■ Command Line Interface Reference Guide—Provides a comprehensive description of CLI commands, syntax, and operations.

■ Event Log Message Reference Guide—Provides a comprehensive descrip-tion of event log messages.

■ Comware CLI Commands in ProVision Software —Lists and describes the Comware CLI commands supported in ProVision Software.

■ Release Notes—Describe new features, fixes, and enhancements that become available between revisions of the main product guide.

Common-CLI-Phase-3-Sept-2012.book Page xv Sunday, September 9, 2012 6:00 PM

http://h20000.www2.hp.com/bizsupport/TechSupport/Product.jsp?lang=en&cc=us&taskId=101&contentType=SupportManual&docIndexId=64180&prodTypeId=12883&prodCatId=82675

1-1

Introduction To the ProVision CLIComware Command Support in ProVision Software

1

Introduction To the ProVision CLI

Comware Command Support in ProVision Software

The selected Comware CLI commands described in this guide are included in the ProVision software CLI to help Comware-experienced network manage-ment staff learn to use the ProVision software CLI with a minimum of effort.

This edition of Comware CLI Commands in ProVision Software describes the operation and output of selected Comware display commands added to the ProVision software. Included are related ProVision software commands and references to further information on configuring the features reflected in the display command output.

Refer to the latest release notes for your switch product to determine whether Comware commands are supported.

HP Networking Switches Running Comware Software

HP Networking Switches Running ProVision Software with Comware CLI Commands Included*

3100330036003610

4200G4210

4210G4500G4510G4800G

5120 El5120 Sl

55005500 E5500 Hl5500 SL5500G58005810

582058305900750095001050012500

3500 3500 yl5400 zl6200 yl

66008200 zl

3800 2910al 26152915

2620

*As of September, 2012. Supported commands depend on software version running on the switch.

Common-CLI-Phase-3-Sept-2012.book Page 1 Sunday, September 9, 2012 6:00 PM

1-2

Introduction To the ProVision CLIListing Display Commands in the CLI

Commands Added to the Software Over Several Releases. The Comware command set available on your switch is determined by the code version it is running. Each command description in this guide includes the minimum software version supporting that command. For example, a minimum version of 15.10 means that a switch running K-code must be using Release K.15.10 or greater and a switch running RA-code must be using RA.15.10 or greater.

Listing Display Commands in the CLI

Use this command: display ?

For example:

HP Switch> display ? boot-loader Display boot loader information clock Clock status and configuration information. command-alias Display command alias debugging Current setting of debugging switches. dns DNS status and configuration information gvrp GARP VLAN Registration Protocol history-command The historical command information. igmp IGMP status and configuration information ip Specify IP(Internet Protocol) configuration information. lacp Display LACP protocol information link-aggregation Display Link-aggregation information memory Display memory information. mld MLD status and configuration information. ospf Open Shortest Path First (OSPF) ospfv3 Open Shortest Path First for IPv6 (OSPFv3) schedule Schedule system task snmp-agent SNMP status and configuration information HP Switch> display


1-3

Introduction To the ProVision CLICLI Operation

CLI Operation

Comparing Comware and ProVision Commands

Comware display commands and ProVision software show commands produce status information used for monitoring, troubleshooting, and auditing the switch network environment and configuration.

■ Like show commands, using display commands does not change the switch operating mode.

■ Comware display commands are additional commands supported in Pro-Vision software, and do not replace any existing ProVision commands.

Output Differences Between Display and Show commands

The output fields from display commands and their show command counter-parts include differences in the names, numbers and types of information fields. For example the results for the following commands have two instances where there is not a comparable mapping between Comware and ProVision:

DNS Field Mappings.

Comware Related ProVision

display dns < domain | server > show ip dnsshow ip


No. n/a

DNS Server Priority

Type DNS Mode

Domain-name Domain Suffix

IP Address DNS Server Addresses

n/a DNS Servers Configured


1-4


Using both the display commands and their show command counterparts can in some cases result in more information output than using only one or the other.

In some cases, a field populated in Comware display output is not populated in the corresponding display output in ProVision software. This is often due to MIB (Management Information Base) differences between Comware and ProVision software. Also, in rare cases, the Comware display output in ProVi-sion software includes fields that are not included in the same display command output in Comware software.

Using CLI Context Levels

ProVision software operates in these CLI context levels:

Use exit to return to the next-highest context level.

Listing Commands Available at Any Context Level. At a given context level you can list and execute the commands that level offers, plus all of the commands available at preceding levels. To list available commands, use the [?] key. For example:

Use the [Tab] or [?] Key To Complete a Command Keyword. You can use [Tab] or [?] to help you find CLI commands or to quickly complete a keyword. For example:

Level Prompt Context Keyword

Operator HP Switch>

Manager HP Switch# enable

Global Configuration HP Switch(config)# config

Context Configuration HP Switch(vlan-1)# HP Switch(eth-A1-A6)#

vlan n interface << portx >[-portn] >

HP Switch# show vlans ? custom Show vlan parameters in customized order. ports Show VLANs that have at least one port from the 'PORT-LIST' as a member. VLAN-ID Show detailed VLAN information for the VLAN with the ID supplied. <cr>


1-5


HP Switch(config) # show ip a[Tab] aspath-list authorized-managers

HP Switch(config) # show ip au[?] HP Switch(config)# show ip authorized-managers [Enter]

IPV4 Authorized Managers ------------------------ Address : 10.10.123.39 Mask : 255.255.255.255 Access : Manager Access Method : all

Empty Output

In some cases where the MIB is not holding information for a feature, the related display command(s) will return only the system prompt. For example, IGMP can be configured, but no data will be displayed unless one or more multicast groups have been joined. For example, using display igmp group when there are no joined multicast groups returns only the system prompt:

HP Switch# display igmp group HP Switch#

Further CLI Operating Information

For more information on using the CLI, refer to the chapter titled “Using the Command Line Interface (CLI)” in the latest Basic Operation Guide for your switch.

To access the latest software manual set for your switch, visit

www.hp.com/support/manuals


http://h20000.www2.hp.com/bizsupport/TechSupport/ProductRoot.jsp?locale=en_US&taskId=101&docIndexId=64180&contentType=SupportManual&

2-1

Display Commandsdisplay arp

2

Display Commands

display arp

Displays ARP (Address Resolution Protocol) configuration information.

Field Descriptions

IP Address: IP address in an ARP entry.

MAC Address: MAC address in an ARP entry.

VLAN ID: VLAN ID contained in a static ARP entry

Interface: Outbound interface in an ARP entry.

Aging: Age timer for a dynamic ARP entry in minutes.

Type: ARP entry type:

• D for Dynamic

• S for Static

• L for Local

• I for Invalid


display arp show arp

HP Switch(config)# display arp

Type: S-Static D-Dynamic L-Local I-Invalid O-Other

IP Address MAC Address VLAN ID Interface Aging Type120.85.204.1 002347-bbd940 1 1 n/a D


2-2

Display Commandsdisplay arp

• O for Other

Operating Notes

The types “A” for authorized, and “M” for multiple ports, are not supported.

For more on switch ARP operation, refer to the “IP Routing” chapter in the latest Multicast and Routing Guide for your switch.

Example of Related ProVision Software Command Output.

display arp Field Mappings.

Minimum Software Version: 15.09.

Comware ProVision Software

IP Address IP Address

MAC Address MAC Address

VLAN ID n/a

Interface Port

Aging n/a

Type Type

HP Switch# show arp

IP ARP table

IP Address MAC Address Type Port --------------- ----------------- ------- ---- 15.255.128.1 00000c-07ac00 dynamic 1 15.255.130.156 001635-679d6c dynamic 1 15.255.131.209 0025b3-4afd68 dynamic 1


2-3

Display Commandsdisplay arp detection

display arp detection

Displays arp-protected VLANs.

HP Switch# display arp detectionARP detection is enabled in the following VLANs: 1-100


HP Switch# show arp-protectARP Protection InformationEnabled Vlans : 1-4094Validate : dest-mac, src-macPort Trust----- -----B1 YesB2 YesB3 NoB4 NoB5 No

For more information, see the latest Access Security Guide for your switch.



display arp detection show arp-protect


2-4

Display Commandsdisplay arp detection statistics

display arp detection statistics

Displays the statistics of the detected arp.

HP Switch# display arp detection statistics

ARP detection is enabled in the following VLANs:

1-10

ARP Protection Counters for VLAN 1

ARPs forwarded : 0 Bad Sender/Target IP : 0 Bad bindings : 0 Source/Sender MAC mismatches : 0 Malformed pkts : 0 Dest/Target MAC mismatches : 0








HP Switch# show arp-protect statistics 1

ARP Protection Counters for VLAN 1 ARPs forwarded : 0 Bad Sender/Target IP : 0 Bad bindings : 0 Source/Sender MAC mismatches : 0 Malformed pkts : 0 Dest/Target MAC mismatches : 0



display arp detection statistics show arp-protection statistics


2-5

Display Commandsdisplay arp ip-address

display arp ip-address

Displays the ARP entry for a specified IP address.

HP Switch# display arp 20.1.1.1

Type: S-Static D-Dynamic L-Local I-Invalid O-Other

IP Address MAC Address VLAN ID Interface Aging Type20.1.1.1 002347-bbd940 1 1 n/a D


HP Switch# show arpIP ARP tableIP Address MAC Address Type Port--------------- ----------------- ------- ----15.255.128.1 00000c-07ac00 dynamic B115.255.131.19 00a0c9-b1503d dynamic15.255.133.150 000bcd-3cbeec dynamic B1

Operating Notes

For more information, refer to the latest Management and Configuration

Guide for your switch.



display arp ip-address show arp


2-6

Display Commandsdisplay boot-loader

display boot-loader

Displays the current flash memory precedence and the source of the current boot file (software image). The switch has two flash memory locations: primary and secondary. In the display boot-loader output:■ btm.swi is the primary flash memory.

■ secondary.swi is the secondary flash memory.

When the switch is configured with primary flash as the default boot source, this command shows that the primary boot file (software image) is in primary flash (btm.swi):

HP Switch# display boot-loader The next primary boot file of MM is: flash:/cfa0/btm.swi The next backup boot file of MM is: flash:/cfa0/secondary.swi The current boot file of MM is: flash:/cfa0/btm.swi

When the switch is configured with secondary flash as the default boot source, this command shows that the primary boot file (software image) is in second-ary flash (secondary.swi):

HP Switch# display boot-loader The next primary boot file of MM is: flash:/cfa0/secondary.swi The next backup boot file of MM is: flash:/cfa0/btm.swi The current boot file of MM is: flash:/cfa0/secondary.swi

Field Descriptions

next primary boot file: The current default flash memory location for the next reload or boot operation.Can be either the primary or secondary flash.

next backup boot file: The current non-default flash memory location. Can be either the primary or secondary flash.

current boot file: The flash memory location from which the switch was last booted. Can be either primary or secondary flash.

Note “of MM” appears in the display boot-loader output on switches that support dual memory modules, and refers to the current active (Actv) memory module.


display boot-loader show flash


2-7

Display Commandsdisplay boot-loader

Operating Notes

Both the primary flash and a secondary flash contain a software image. Any valid software image can be loaded into either flash memory.

This command indicates which flash memory is the default when the switch is booted with any of the following commands:

reload

boot [system ]

To change the flash memory default, use this command:

boot set-default flash < primary | secondary >

For more on switch memory operation, refer to the “Switch Memory and Configuration” chapter in the latest Basic Operation Guide for your switch.

Example of Related ProVision software Command Output.

HP Switch# show flashImage Size (bytes) Date Version

----------------- ------------ -------- --------------

Primary Image : 14995368 12/20/11 K.15.07.0003

Secondary Image : 14995368 12/20/11 K.15.08.0001

Boot ROM Version : K.15.26

Default Boot : Primary

Boot-Loader Field Mappings.


Comware ProVision software

btm.swi Primary Image

secondary.swi Secondary Image

n/a Boot ROM Version

current boot file Default Boot


2-8

Display Commandsdisplay clock

display clock

Displays the current time, time zone, day, and date setting on the switch.

HP Switch# display clock 16:07:27 GMT Mon 03/16/2012

Field Descriptions:

Time: Current time in HH:MM:SS format on the switch.

Time Zone: GMT (default) or the configured time zone.

Day: Mon, Tue, Wed, thu, Fri, Sat, Sun

Date: MM/DD/YYYY format

Operating Notes

To configure time, date, daylight-time-rule, time zone and other time or date settings on the switch, use the following commands in the config context to list the time and date command options:

time ?

clock ?


HP Switch# show time Mon Mar 16 16:07:56 2012

The output of the ProVision software show system information command includes the switch’s time zone and Daylight Time Rule settings.

To configure time and date settings on the switch, use the clock and time commands in the config context. For more information, see the “Time Proto-cols” chapter in the latest Management and Configuration Guide for your switch.



display clock show timeshow system information


2-9

Display Commandsdisplay command-alias

display command-alias

Displays any defined command aliases and their corresponding command assignments configured on the switch. For example, suppose the following aliases are configured:

Alias Full Command

sst show startup-config

srun show running-config

With the above alias configuration, the display output would be as follows:

HP Switch(config)# display command-alias index alias command key 1 sst show startup-config 2 srun show runnning-config

Field Descriptions

index: The sequence number for each alias.

alias: The character string.

command key: The command called by the alias.

Operating Notes

To configure an alias in ProVision software, use the following command.

alias < alias-name-str > < command-str >

For more on the alias command, refer to the chapter titled “Using the Command Line Interface (CLI)” in the latest Basic Operation Guide for your switch.


display command-alias show alias


2-10

Display Commandsdisplay command-alias

Example of Related ProVision software Command Output.

HP Switch(config)# show alias

Name Command -------------------------------- -------------------------- sst show startup-config srun show runnning-config

Alias Field Mappings.



index n/a

alias Name

command key Command


2-11

Display Commandsdisplay counters

display counters

Displays traffic statistics for interfaces.

Field Descriptions

Interface: Abbreviated interface name.

Total (pkts): Total number of packets received or sent through the interface.

Broadcast (pkts): Total number of broadcast packets received or sent through the interface. On an RPR physical port, all broadcast and multicast packets received or sent are displayed as multicast packets.


display counters show interface <port>

HP Switch# display counters inbound interfaceInterface Total(pkts) Broadcast(pkts) Multicast(pkts) Err(pkts)A1 11 2 5 0A2 0 0 0 0A3 0 0 0 0A4 0 0 0 0A5 0 0 0 0A6 0 0 0 0A7 0 0 0 0...

HP Switch# display counters outbound interfaceInterface Total(pkts) Broadcast(pkts) Multicast(pkts) Err(pkts)A1 13 6 6 0A2 0 0 0 0A3 0 0 0 0A4 0 0 0 0A5 0 0 0 0A6 0 0 0 0A7 0 0 0 0...


2-12


Multicast (pkts): Total number of multicast packets received or sent through the interface. On an RPR physical port, all broadcast and multicast packets received or sent are displayed as multicast packets.

Err (pkts): Total number of error packets received or sent through the interface.

Overflow: more than 14 decimal digits(7 digits for column “Err”): The com-mand displays Overflow in any of the following cases:

• The data length of an error statistic is greater than 7 decimal digits.

The data length of a non-error statistic is greater than 14 decimal digits.

--: not supported: The statistical item is not supported.

Operating Notes

For more information on interface counters, see the “Port Status and Config-uration” chapter in the latest Management and Configuration Guide for your switch.


2-13



display counters Field Mappings.

HP Switch(config)# show interface a1

Status and Counters - Port Counters for port A1

Name : O’[email protected] MAC Address : 001871-b995ff Link Status : Up Totals (Since boot or last clear) : Bytes Rx : 2,763,197 Bytes Tx : 22,972 Unicast Rx : 2044 Unicast Tx : 128 Bcast/Mcast Rx : 23,456 Bcast/Mcast Tx : 26 Errors (Since boot or last clear) : FCS Rx : 0 Drops Tx : 0 Alignment Rx : 0 Collisions Tx : 0 Runts Rx : 0 Late Colln Tx : 0 Giants Rx : 0 Excessive Colln : 0 Total Rx Errors : 0 Deferred Tx : 0 Others (Since boot or last clear) : Discard Rx : 0 Out Queue Len : 0 Unknown Protos : 0 Rates (5 minute weighted average) : Total Rx (bps) : 3,028,168 Total Tx (bps) : 1,918,384 Unicast Rx (Pkts/sec) : 5 Unicast Tx (Pkts/sec) : 0 B/Mcast Rx (Pkts/sec) : 71 B/Mcast Tx (Pkts/sec) : 0 Utilization Rx : 00.30 % Utilization Tx : 00.19 %


Interface port

Total (pkts) Bytes Rx and Bytes Tx

Broadcast (pkts) Bcast/Mcast Rx and Bcast/Mcast Tx

Multicast (pkts) Bcast/Mcast Rx and Bcast/Mcast Tx

Err (pkts) Errors


2-14



Overflow: n/a

-: not supported n/a



2-15

Display Commandsdisplay counters rate

display counters rate

Displays traffic rate statistics over the last 300 seconds. The statistics cover only interfaces in up state.

HP Switch# display counters rate outbound interfaceInterface Total(pkts/sec) Broadcast(pkts/sec) Multicast(pkts/sec)A1 84 0 42A2 0 0 0

Overflow: n/a --: not supported.

HP-5406zl# display counters rate inbound interfaceInterface Total(pkts/sec) Broadcast(pkts/sec) Multicast(pkts/sec)A1 0 0 0A2 88 0 44

Overflow: n/a --: not supported.

When all ports are down:

HP Switch# display counters rate outbound interface No statistics, or no counted interface.


HP Switch# show int custom 1-4 port name:4 type vlan intrusion speed enabled mdiStatus and Counters - Custom Port Status IntrusionPort Name Type VLAN Alert Speed Enabled MDI-mode---- ---- ---- ------ ------- --------- ------- ------1 Acco 100/1000T 1 No 1000FDx Yes Auto2 Huma 100/1000T 1 No 1000FDx Yes Auto3 Deve 100/1000T 1 No 1000FDx Yes Auto4 Lab1 100/1000T 1 No 1000FDx Yes Auto

Operating Notes





display counters rate show int <int>


2-16

Display Commandsdisplay cpu-usage

display cpu-usage

Displays average CPU usage statistics for 5 seconds, 1 minute and 5 minutes.

HP Switch# display cpu-usage

Master CPU usage: 6% in last 5 seconds 4% in last 1 minute 3% in last 5 minutes


HP Switch# show cpu2 percent busy, from 2865 sec ago1 sec ave: 9 percent busy5 sec ave: 9 percent busy1 min ave: 1 percent busy

% CPU | Description-------+--------------------------99 | Idle

Operating Notes





display cpu-usage show cpu [slot <SLOT-ID-RANGE> [ <time>] | <time>]


2-17

Display Commandsdisplay cpu-usage history

display cpu-usage history

Displays the history CPU utilization rates in a coordinate plane. The system collects the statistics of history CPU utilization rates at a certain interval and saves the statistics in the history record area. You can use the this command to display the history CPU utilization rates in the last 5 minutes. The history CPU utilization rates are displayed through x and y coordinates.

Any CPU utilization statistics value takes the closest y-coordinate value. For example, a statistics value of 53% is displayed as 55%, and a statistics value of 52% is displayed as 50%.

A number sign (#) shows the CPU utilization rate at a time point. If more than one number sign exists at a time point, the highest one represents the CPU utilization rate of the time point.

HP Switch# display cpu-usage history

100%| 95%| 90%| 85%| 80%| 75%| 70%| 65%| 60%| 55%| 50%| 45%| 40%| 35%| 30%| 25%| 20%| 15%| 10%| 5%|######################################################## --------------------------------------------------------- 50 100 150 200 250 300 (seconds) cpu-usage last 05 minutes(SYSTEM)



display cpu-usage history No equivalent ProVision software command


2-18

Display Commandsdisplay current-configuration

display current-configuration

Displays the current configuration.

HP Switch# display current-configurationJ8697A Configuration Editor; Created on release #K.15.09.0000xVer #03:01.1f.ef:f2hostname "HP-5406zl"module 1 type J9536Amodule 6 type J9534Asnmp-server community "public" Unrestrictedvlan 1 name "DEFAULT_VLAN" untagged A1-A22,F1-F24 ip address dhcp-bootp exit


HP Switch# show running-configRunning configuration:; J9087A Configuration Editor; Created on release #R.11.XXhostname "Switch"snmp-server community "public" Unrestrictedsnmp-server host 15.255.133.236 "public"snmp-server host 15.255.133.222 "public"snmp-server host 15.255.133.70 "public"snmp-server host 15.255.134.235 "public"vlan 1name "DEFAULT_VLAN"untagged 1-28ip address dhcp-bootpexitsnmp-server enable traps mac-notify mac-movesnmp-server enable traps mac-notify trap-interval 60snmp-server enable traps mac-notifymac-notify traps 5-6 learnedmac-notify traps 3-4 removed

For more information, see the latest Management and Configuration Guide for your switch.



display current-configuration show running-configuration


2-19

Display Commandsdisplay current-configuration by-linenum

display current-configuration by-linenum

Displays the number of each line.

HP Switch# display current-configuration by-linenum 1: J8697A Configuration Editor; Created on release #K.15.09.0000x 2: Ver #03:01.1f.ef:f2 3: hostname "HP-5406zl" 4: module 1 type J9536A 5: module 6 type J9534A 6: snmp-server community "public" Unrestricted 7: vlan 1 8: name "DEFAULT_VLAN" 9: untagged A1-A22,F1-F24 10: ip address dhcp-bootp 11: exit






display current-configuration by-linenum show running-configuration


2-20

Display Commandsdisplay current-configuration configuration

display current-configuration configuration

Displays active configuration in the system excluding vlan and interface configuration. This command is available only in manager mode.

HP Switch# display current-configuration configurationhostname "HP-6200yl-24G" module 1 type J8992A alias "view" "show" banner motd "\n" radius-server host 10.10.10.1 key "abcd" ip access-list extended "grp1" exit snmp-server community "public" Unrestricted no snmpv3 enable snmpv3 enable snmpv3 group ComOperatorR user "user4" sec-model ver3 snmpv3 user "initial" snmpv3 user "user4" aaa port-access authenticator active arp-protect



display current-configuration configuration No equivalent ProVision software command


2-21

Display Commandsdisplay current-configuration interface

display current-configuration interface

Displays the interface configuration.

HP Switch# display current-configuration interface vlan 1 name "DEFAULT_VLAN" untagged A1-A22,F1-F24 ip address dhcp-bootp exitinterface A1 untagged vlan 1 exitinterface A2 untagged vlan 1 exitinterface A3 untagged vlan 1 exitinterface A4 untagged vlan 1 exitinterface A5 untagged vlan 1 exitinterface A6 untagged vlan 1 exitinterface A7 untagged vlan 1 exitinterface A8 untagged vlan 1 exitinterface A9 untagged vlan 1 exitinterface A10 untagged vlan 1 exitinterface A11 untagged vlan 1 exitinterface A12


display current-configuration interface show running-configuration


2-22

Display Commandsdisplay current-configuration interface

untagged vlan 1 exitinterface A13 untagged vlan 1 exitinterface A14 untagged vlan 1 exitinterface A15 untagged vlan 1 exitinterface A16 untagged vlan 1 exitinterface A17 untagged vlan 1 exitinterface A18 untagged vlan 1 exitinterface A19 untagged vlan 1



For more information, see the latest Management and Configuration Guide for your switch.Minimum Software Version: 15.09.


2-23

Display Commandsdisplay debugging

display debugging

Displays the options from any of the following lists that have debug logging enabled.

Using display debugging without specifying an option lists all options in the set that are enabled for debug logging. For example, if acl, ip, lldp, and policy are enabled for debugging, this command produces the following:

HP Switch# display debugging ip ospf spf debugging is on acl log debugging is on lldp log debugging is on policy route-map debugging is on HP Switch#

Using display debugging with a specific option lists that option if it is enabled for debug logging. If the command returns only the CLI prompt, then the option is not enabled for debug logging. For example, if acl is enabled for debug logging and vrrp s not, this command produces the following:

HP Switch# display debugging acl log debugging is on HP Switch# display debugging vrrp HP Switch#

Operating Notes

To configure debug operation in ProVision software, use the following command.

debug < option >

For more on configuring debug operation, refer to the chapter titled “Trouble-shooting” in the latest Management and Configuration Guide for your switch.


display debugging [ option ] show debug [buffer [-c < count > | -r | option-str ]]

acl distributed-trunking ip lldp snmp

arp-protect dynamic-ip-lockdown ipv6 policy vrrp

cdp event lacp security


2-24

Display Commandsdisplay debugging


HP Switch# show debug

Debug Logging

Source IP Selection: Outgoing Interface Destination: Memory buffer

Enabled debug types: ip ospf spf acl log lldp log policy route-map

Debug Field Mappings.



n/a Source IP Selection

n/a Destination

debug types listed Enabled debug types


2-25

Display Commandsdisplay default-configuration

display default-configuration

Displays factory defaults of the switch, and all commands to be executed when the switch boots with the factory defaults.

HP Switch# display default-configuration; J8693A Configuration Editor; Created on release #K.15.09.0000x; Ver #03:01.1f.ef:f2vlan 1 name "DEFAULT_VLAN" ip address dhcp-bootp exit



display default-configuration No equivalent ProVision software command


2-26

Display Commandsdisplay device

display device

Displays physical modules present in the switch. This command also identifies the status of these modules, whether they are up/active/standby or failed etc.

HP Switch# display deviceSlotNo. Brd Type BrdStatus SubSlotNum SftVer PatchVerMM1 HP J9092A Management Modul... Standby n/a K.15.09.0000x n/aMM2 HP J9092A Management Modul... Active n/a K.15.09.0000x n/aSSM HP J9095A System Support M... Normal n/a K.15.09.0000x n/aFM1 HP J9093A Fabric Module 82... Enabled n/a K.15.09.0000x n/aFM2 HP J9093A Fabric Module 82... Enabled n/a K.15.09.0000x n/aA HP J9536A 20p GT PoE+/2p S... Up n/a K.15.09.0000x n/a

Field Descriptions:

Slot No.: Slot number of a card (standalone mode); slot number of a card on the specified member switch in the format of member ID/slot number (IRF mode)

Brd Type: Hardware type of a card, which can be the following values:

• Specific card model, such as LST1MRPNC1, which is the same as the silkscreen.

• NONE: No card is in the slot.

• UNKNOWN: The card is not supported by the software version and thus cannot start normally.

Brd Status: Card status, which can be the following values:

• Absent: No card is in the slot.

• Master: The card is an AMB.

• Slave: The card is an SMB.

• Normal: The card is an interface card and functions normally.

• Fault: The card has not been booted or an error occurred to the card.

• Off: The card is not powered on.

• Illegal: The card is not supported by the software version and thus cannot start normally.

Subslot Num: Number of subcards


display device No equivalent ProVision software command


2-27

Display Commandsdisplay device

Sft Ver: Software version of the current card, which can be the following values:

• Specific software version: The software version of the switch.

• NONE: No card is in the slot.

• Mismatched: The software version does not support the card and thus cannot be uploaded.



2-28

Display Commandsdisplay dhcp relay information all

display dhcp relay information all

Displays option 82 configuration information on the DHCP relay agent.

HP Switch# display dhcp relay information allInterface: Vlan-interface1 Status: Disable Strategy: Replace Format: Normal Circuit ID format-type: HEX Remote ID format-type: HEXInterface: Vlan-interface10 Status: Enable Strategy: Replace Format: Normal Circuit ID format-type: HEX Remote ID format-type: HEX



display dhcp relay information all No equivalent ProVision software command


2-29

Display Commandsdisplay dhcp relay information interface Vlan-interface <vlan-id>

display dhcp relay information interface Vlan-interface <vlan-id>

Displays option 82 configuration information on the DHCP relay agent based on vlan.

HP Switch# display dhcp relay information interface Vlan-interface 10Interface: Vlan-interface10 Status: Enable Strategy: Replace Format: Normal Circuit ID format-type: HEX Remote ID format-type: HEX



display dhcp relay information interface Vlan-interface <vlan-id>

No equivalent ProVision software command


2-30

Display Commandsdisplay dhcp relay statistics

display dhcp relay statistics

Displays DHCP packet statistics related to a specified or all DHCP server groups. DHCP relay statistics identifies the UDPF_DHCP_MSG PDUs and provides the information regarding the number and type of PDUs being received/relayed from/to client and server. It also distinguishes the type of packets (DISCOVER, REQUEST, INFORM, DECLINE, RELEASE, BOOTPRE-QUEST, OFFER, ACK, NAK) along with bad packets.


display dhcp relay statistics show dhcp-relay


2-31


Field Descriptions

The following fields are for bad packets received.

■ DHCP packets received from clients:• DHCPDISCOVER packets received

• DHCPREQUEST packets received

• DHCPINFORM packets received

• DHCPRELEASE packets received

• DHCPDECLINE packets received

• BOOTPREQUEST packets received

HP Switch# display dhcp relay statistics Bad packets received: 0DHCP packets received from clients: 2 DHCPDISCOVER packets received: 1 DHCPREQUEST packets received: 1 DHCPINFORM packets received: 0 DHCPRELEASE packets received: 0 DHCPDECLINE packets received: 0 BOOTPREQUEST packets received: 0DHCP packets received from servers: 2 DHCPOFFER packets received: 1 DHCPACK packets received: 1 DHCPNAK packets received: 0 BOOTPREPLY packets received: 0DHCP packets relayed to servers: 2 DHCPDISCOVER packets relayed: 1 DHCPREQUEST packets relayed: 1 DHCPINFORM packets relayed: 0 DHCPRELEASE packets relayed: 0 DHCPDECLINE packets relayed: 0 BOOTPREQUEST packets relayed: 0DHCP packets relayed to clients: 2 DHCPOFFER packets relayed: 1 DHCPACK packets relayed: 1 DHCPNAK packets relayed: 0 BOOTPREPLY packets relayed: 0DHCP packets sent to servers: n/a DHCPDISCOVER packets sent: n/a DHCPREQUEST packets sent: n/a DHCPINFORM packets sent: n/a DHCPRELEASE packets sent: n/a DHCPDECLINE packets sent: n/a BOOTPREQUEST packets sent: n/aDHCP packets sent to clients: n/a DHCPOFFER packets sent: n/a DHCPACK packets sent: n/a DHCPNAK packets sent: n/a BOOTPREPLY packets sent: n/a


2-32


■ DHCP packets received from servers:• DHCPOFFER packets received

• DHCPACK packets received

• DHCPNAK packets received

• BOOTPREPLY packets received

■ DHCP packets relayed to servers:• DHCPDISCOVER packets relayed

• DHCPREQUEST packets relayed

• DHCPINFORM packets relayed

• DHCPRELEASE packets relayed

• DHCPDECLINE packets relayed

• BOOTPREQUEST packets relayed

■ DHCP packets relayed to clients:• DHCPOFFER packets relayed0

• DHCPACK packets relayed

• DHCPNAK packets relayed

• BOOTPREPLY packets relayed

■ DHCP packets sent to servers:• DHCPDISCOVER packets sent

• DHCPREQUEST packets sent

• DHCPINFORM packets sent

• DHCPRELEASE packets sent

• DHCPDECLINE packets sent

• BOOTPREQUEST packets sent

■ DHCP packets sent to clients:• DHCPOFFER packets sent

• DHCPACK packets sent

• DHCPNAK packets sent

• BOOTPREPLY packets sent

Operating Notes

For more information about IPv6 DHCP, see the “DHCPv6 Relay” chapter in the latest IPv6 Configuration Guide for your switch.


2-33



display dhcp relay statistics Field Mappings.

The Comware output does not correlate to the ProVision output.


HP Switch(config)# show dhcp-relay DHCP Relay Agent : Enabled DHCP Request Hop Count Increment : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : replace Remote ID : mac

DHCP Relay Statistics:

Client Requests Server Responses

Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 0 0 0 0

DHCP Relay Option 82 Statistics:


Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 0 0 0 0


2-34

Display Commandsdisplay dhcp-snooping binding database

display dhcp-snooping binding database

Displays the DHCP snooping binding file information.

HP Switch# display dhcp-snooping binding databaseFile name : cfa0:/database.dhcpUpdate interval : 10 minutesLatest read time : n/aLatest write time : Jul 15 2008 16:38:24Status : Last write succeeded.


HP Switch# show dhcp-snoopingDHCP Snooping InformationDHCP Snooping : YesEnabled Vlans :Verify MAC : YesOption 82 untrusted policy : dropOption 82 Insertion : YesOption 82 remote-id : macStore lease database : Not configuredPort Trust----- -----B1 NoB2 No




display dhcp-snooping binding database show dhcp-snooping


2-35

Display Commandsdisplay dhcp-snooping information

display dhcp-snooping information

Displays information about dhcp snooping when option 82 is enabled.

HP Switch# display dhcp-snooping information all Interface: A1 Status: Enable Strategy: Drop Format: n/a Remote ID format-type: HEX User defined : Remote ID: 0026f1-0faf00

Interface: A2 Status: Enable Strategy: Drop Format: n/a Remote ID format-type: HEX User defined: Remote ID: 0026f1-0faf00

... (contd. for all ports)


HP Switch# show dhcp-snoopingDHCP Snooping InformationDHCP Snooping : YesEnabled Vlans :Verify MAC : YesOption 82 untrusted policy : dropOption 82 Insertion : YesOption 82 remote-id : macStore lease database : NotPort Trust----- -----B1 NoB2 No

Operating Notes

For more information, refer to the latest Access Security Guide for your switch.



display dhcp-snooping information show dhcp-snooping


2-36

Display Commandsdisplay dhcp-snooping [ip ip_address]

display dhcp-snooping [ip ip_address]

Displays the user IP-MAC address mapping entries recorded by the DHCP snooping function.

HP Switch# display dhcp-snoopingDHCP Snooping is enabled. The client binding table for all untrusted ports. Type : D--Dynamic , S--Static , R--Recovering Type IP Address MAC Address Lease VLAN SVLAN Interface---- ----------- --------------- ---------- ---- ----- --------- S 192.168.1.1 0050-569f-2c8b static 1 n/a 1 S 192.168.1.2 0050-569f-2c8c static 2 n/a 9 S 192.168.1.3 0050-569f-2caa static 3 n/a 3 S 192.168.1.4 0050-569f-2c8a static 4 n/a 7 S 192.168.1.5 0050-569f-2c8d static 5 n/a 5 --- 5 dhcp-snooping item(s) found ---


HP Switch# show dhcp-snooping bindingMacAddress IP VLAN Interface Time left----------------- --------------- ---- --------- ---------22.22.22.22.22.22 10.0.0.1 4 B2 1600




display dhcp-snooping [ip ip_address] show dhcp-snooping binding


2-37

Display Commandsdisplay dhcp-snooping packet statistics

display dhcp-snooping packet statistics

Displays the statistics of the dhcp snooping packets.

HP Switch# display dhcp-snooping packet statistics DHCP packets received : 2 DHCP packets send : 0 Packets dropped due to rate limitation : n/a Dropped invalid packets : 0


HP Switch# show dhcp-snooping statistics

Packet type Action Reason Count

----------- ------- ---------------------------- ---------

server forward from trusted port 0

client forward to trusted port 0

server drop received on untrusted port 0

server drop unauthorized server 0

client drop destination on untrusted port 0

client drop untrusted option 82 field 0

client drop bad DHCP release request 0

client drop failed verify MAC check 0



display dhcp-snooping packet statistics show dhcp-snooping statistics


2-38

Display Commandsdisplay dhcp-snooping trust

display dhcp-snooping trust

Displays information about trusted ports.

Field Descriptions

Interface: Interface

Trusted: The interface is trusted or not trusted.

Operating Notes

For more information about DHCP snooping, see the “Configuring Advanced Threat Protection” chapter in the latest Access Security Guide for your switch.


display dhcp-snooping trust show dhcp-snooping

HP Switch(config)# display dhcp-snooping trust

DHCP Snooping is enabled.DHCP Snooping trust becomes active. Interface Trusted ========================= ============ A1 Trusted A2 Trusted A3 Trusted A4 Trusted


2-39

Display Commandsdisplay dhcp-snooping trust


display dhcp-snooping trust Field Mappings.



DHCP snooping is enabled DHCP Snooping (yes/no)

Interface Port

Trusted Trust

HP Switch(config)# show dhcp-snooping

DHCP Snooping Information

DHCP Snooping : Yes

Enabled Vlans :

Verify MAC : Yes

Option 82 untrusted policy : drop

Option 82 Insertion : Yes

Option 82 remote-id : mac

Store lease database : Not configured

Port Trust

----- -----

B1 No

B2 No


2-40

Display Commandsdisplay diagnostic-information

display diagnostic-information

Displays different levels of diagnostic information. This is an alias to the ProVision command show tech and shares the same behavior.

HP Switch# show tech

show system

Status and Counters - General System InformationSystem Name : 5400_1System Contact :System Location :

MAC Age Time (sec) : 300

Time Zone : 0Daylight Time Rule : None

Software revision : K.14.XX Base MAC Addr : 001871-c42f00ROM Version : K.12.12 Serial Number : SG641SU00L

Up Time : 23 hours Memory - Total :CPU Util (%) : 10 Free :IP Mgmt - Pkts Rx : 759 Packet - Total : 6750Pkts Tx : 2 Buffers Free : 5086Lowest : 4961Missed : 0show flashImage Size(Bytes) Date Version----- ---------- -------- -----------



display diagnostic-information show tech


2-41

Display Commandsdisplay dns domain

display dns domain

Displays all the domain name suffixes that are appended to host names by the resolver before sending the queries to name servers. These domain name suffixes could have been statically configured on the switch or obtained from the DHCP server dynamically.

HP Switch# display dns domain Type: D:Dynamic S:Static

No. Type Domain-name1 S hp5.com2 S hp.in3 S hp.us


HP Switch# show ip dnsDNS Mode : DHCPDomain Suffix : pubs.outdoors.com

DNS Servers Configured:----------------------10.28.229.10

Priority DNS Server Addresses-------- --------------------1 10.28.192.1

Operating Notes





display dns domain show ip dns


2-42

Display Commandsdisplay dns domain dynamic

display dns domain dynamic

Displays all the domain name suffixes that are obtained from the DHCP server dynamically.

HP Switch# display dns domain dynamic

Type: D:Dynamic S:Static

No. Type Domain-name1 D hp2.net2 D hp3.net3 D hp4.net



display dns domain dynamic No equivalent ProVision software command


2-43

Display Commandsdisplay dns < domain | server >

display dns < domain | server >

Displays the current IPv4 DNS domain name suffixes and server configuration.

HP Switch# display dns domain Type: D:Dynamic S:Static

No. Type Domain-name 1 S atlantic.widgetcorp.net

HP Switch# display dns server

Type: D:Dynamic S:Static

DNS Server Type IP Address 1 S 10.110.34.51 2 S 10.110.34.101

Field Descriptions

No.: Sequence number.

Type: Shows the type of domain name suffix. S means a statically configured domaine name suffix. D means a domain name suffix obtained dynamically through DHCP.

Domain-name: The domain name suffix.

DNS Server: The sequence number of the DNS server.

IP Address: The IPv4 address of the DNS server(s).

Operating Notes

The switch supports one domain suffix entry and two DNS server IP address entries.

To configure DNS operation in ProVision software, use one of the following commands.


display dns < domain | server > show ip dns show ip


2-44

Display Commandsdisplay dns < domain | server >

ip dns dhcp ip dns domain-name < name-str > ip dns server-address priority < 1 | 2 > < ip-addr | ipv6-addr >

For more on configuring dns, refer to the “Troubleshooting” chapter in the latest Management and Configuration Guide for your switch.


HP Switch# show ip dns

DNS Mode : DHCP Domain Suffix : americas.hpqcorp.net

DNS Servers Configured: ---------------------- Priority DNS Server Addresses -------- -------------------- 1. 16.110.135.52 2. 16.110.135.51

DNS Field Mappings.



No. n/a

DNS Server Priority

Type DNS Mode

Domain-name Domain Suffix

IP Address DNS Server Addresses

n/a DNS Servers Configured


2-45

Display Commandsdisplay dns ipv6 server

display dns ipv6 server

Displays IPv6 DNS server information.

Field Descriptions

DNS Server: Sequence number of the DNS server, which is assigned automat-ically by the system, starting from 1.

Type: Type of the DNS server. “S” represents a statically configured DNS server, and “D” represents a DNS server obtained dynamically through DHCP or other protocols.

IPv6 Address: IPv6 address of the DNS server.

Interface Name: Interface name, which is available only for a DNS server with an IPv6 link-local address configured.

Operating Notes

Out-of-band management and tunnel interfaces are supported.

For more information about IPv6 DNS, see the “IPv6 Diagnostic and Trouble-shooting” chapter in the latest IPv6 Configuration Guide for your switch.


display dns ipv6 server show ip dns

HP Switch# display dns ipv6 server Type: D:Dynamic S:Static

DNS Server Type IPv6 Address (Interface Name) 1 S 1::1 2 S FE80:1111:2222:3333:4444:5555:6666:7777 Vlan2


2-46

Display Commandsdisplay dns ipv6 server


display dns ipv6 server Field Mappings.



DNS Server DNS Servers Configured

Type DNS Mode

IPv6 Address DNS Server Addresses

Interface Name n/a

HP Switch(config)# show ip dns

DNS Mode : Manual Domain Suffix : atlantic.widgetcorp.net DNS Servers Configured: ----------------------

Priority DNS Server Addresses -------- -------------------- 1. 10.110.34.51 2. 10.110.34.101


2-47

Display Commandsdisplay dot1x [interface]

display dot1x [interface]

Displays information about 802.1X.

If you specify neither the sessions keyword nor the statistics keyword, the command displays all information about 802.1X, including session informa-tion, statistics, and configurations.


display dot1x [interface interface-list]display dot1x sessions [interface interface-list]display dot1x statistics [interface interface-list]

show port-access authenticator [config | statistics | session counters]


2-48


HP Switch(config)# display dot1x interface A1

Equipment 802.1X protocol is CHAP authentication is n/a Proxy trap checker is n/a Proxy logoff checker is n/a EAD quick deploy is n/a

Configuration: Transmit Period 30 s, Handshake Period n/a Quiet Period 60 s, Quiet Period Timer is n/a Supp Timeout 30 s, Server Timeout 300 s Reauth Period 3600 s The maximal retransmitting times 2 EAD quick deploy configuration: EAD timeout: n/a

The maximum 802.1X user resource number is n/a per slot Total current used 802.1X resource number is n/a

A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Periodic reauthentication is disabled The port is not an authenticator Authentication Mode is Auto Port Control Type is n/a 802.1X Multicast-trigger is n/a Mandatory authentication domain: n/a Guest VLAN: 0 Auth-Fail VLAN: n/a Max number of on-line users is 0

EAPOL Packet: Tx n/a, Rx n/a Sent EAP Request/Identity Packets : 0 EAP Request/Challenge Packets: 0 EAP Request/Challenge Packets: 0 Received EAPOL Start Packets : 0 EAPOL LogOff Packets: 0 EAP Response/Identity Packets : 0 EAP Response/Challenge Packets: 0 Error Packets: 0

Controlled User(s) amount to n/a


2-49


HP Switch(config)# display dot1x sessions

Equipment 802.1X protocol is enabled CHAP authentication is n/a


A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a


A2 is link-down 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a





2-50


HP Switch(config)# display dot1x statistics Equipment 802.1X protocol is enabled CHAP authentication is n/a


A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a







2-51


Field Descriptions

Equipment 802.1X protocol is enabled: Specifies whether 802.1X is enabled globally.

CHAP authentication is enabled: Specifies whether CHAP authentication is enabled.

Transmit Period: Username request timeout timer in seconds.

Handshake Period: Handshake timer in seconds.

Reauth Period: Periodic re-authentication timer in seconds.

Quiet Period: Quiet timer in seconds.

Quiet Period Timer is disabled: Status of the quiet timer. In this example, the quiet timer is enabled.

Supp Timeout: Client timeout timer in seconds.

Server Timeout: Server timeout timer in seconds.

The maximal retransmitting times: Maximum number of attempts for sending an authentication request to a client.

The maximum 802.1X user resource number per slot: Maximum number of concur-rent 802.1X user per card.

Total current used 802.1X resource number: Total number of online 802.1X users.

GigabitEthernet3/0/1 is link-up: Status of the port. In this example, GigabitEth-ernet 3/0/1 is up.

802.1X protocol is disabled: Specifies whether 802.1X is enabled on the port.

Handshake is disabled: Specifies whether handshake is enabled on the port.

Handshake secure is disabled: Specifies whether handshake security is enabled on the port.

802.1X unicast-trigger is disabled: Specifies whether unicast trigger is enabled on the port.

Periodic reauthentication is disabled: Specifies whether periodic online user re-authentication is enabled on the port.

The port is an authenticator: Role of the port.


2-52


Authenticate Mode is Auto: Authorization state of the port.

Port Control Type is Mac-based: Access control method of the port.

802.1X Multicast-trigger is enabled: Specifies whether the 802.1X multicast-trigger function is enabled.

Mandatory authentication domain: Mandatory authentication domain on the port.

Guest VLAN: 802.1X guest VLAN configured on the port. NOT configured is displayed if no guest VLAN is configured.

Auth-fail VLAN: Auth-Fail VLAN configured on the port. NOT configured is displayed if no Auth-Fail VLAN is configured.

Max number of on-line users: Maximum number of concurrent 802.1X users on the port.

EAPOL Packet: Number of sent (Tx) and received (Rx) EAPOL packets.

Sent EAP Request/Identity Packets: Number of sent EAP-Request/Identity pack-ets.

EAP Request/Challenge Packets: Number of sent EAP-Request/Challenge pack-ets.

EAP Success Packets: Number of sent EAP Success packets.

Fail Packets: Number of sent EAP-Failure packets.

Received EAPOL Start Packets: Number of received EAPOL-Start packets.

EAPOL LogOff Packets: Number of received EAPOL-LogOff packets.

EAP Response/Identity Packets: Number of received EAP-Response/Identity packets.

EAP Response/Challenge Packets: Number of received EAP-Response/Chal-lenge packets.

Error Packets: Number of received error packets.

Controlled User(s) amount: Number of authenticated users on the port.


2-53


Operating Notes

For more on switch 802.1X operation, refer to the “Configuring Port-based and User-based Access Control (802.1X)” chapter in the latest Access Security



HP Switch(config)# show port-access authenticator config

Port Access Authenticator Configuration

Port-access authenticator activated [No] : Yes Allow RADIUS-assigned dynamic (GVRP) VLANs [No] : No | Re-auth Access Max Quiet TX Supplicant Server Cntrl Port | Period Control Reqs Period Timeout Timeout Timeout Dir ---- + ------- -------- ----- ------- -------- ---------- -------- ----- 1 | No Auto 2 60 30 30 30 both 2 | No Auto 2 60 30 30 30 in ...

HP Switch(config)# show port-access authenticator session-counters

Port Access Authenticator Session Counters

Port-access authenticator activated [No] : Yes Allow RADIUS-assigned dynamic (GVRP) VLANs [No] : No Session Session Port Frames In Frames Out Time(sec.) Status User ---- ---------- ----------- ----------- ----------- ------- 2 45623 45623 20 in-progress bert


2-54


display dot1x Field Mappings.

HP Switch(config)# show port-access authenticator statistics

Port Access Authenticator Statistics

Port-access authenticator activated [No] : Yes Allow RADIUS-assigned dynamic (GVRP) VLANs [No] : No

Source TX TX RX RX RX RX RX Port MAC address ReqId Req Start Logoff RespId Resp Errors ---- ------------- ------ ----- ------ ------- ------- ----- ------- 2 001560-b3ea48 1 0 0 0 0 0 0


Equipment 802.1X protocol is enabled Port-access authenticator activated (yes/no)

CHAP authentication is enabled n/a

Transmit Period TX Timeout

Handshake Period n/a

Reauth Period Re-auth Period

Quiet Period Quiet Period

Quiet Period Timer is disabled n/a

Supp Timeout Supplicant Timeout

Server Timeout Server Timeout

The maximal retransmitting times Max Reqs

The maximum 802.1X user resource number per slot

n/a

Total current used 802.1X resource number n/a

GigabitEthernet3/0/1 is link up n/a

802.1X protocol is disabled Port-access authenticator activated (yes/no)

Handshake is disabled n/a

802.1X unicast-trigger is disabled n/a


2-55



Periodic reauthentication is disabled Re-auth Period

The port is an authenticator n/a

Authenticate Mode is Auto Access Control

Port Control Type is Mac-based n/a

802.1X Multicast-trigger is enabled n/a

Mandatory authentication domain n/a

Guest VLAN n/a

Auth-fail VLAN n/a

Max number of on-line users n/a

EAPOL Packet n/a

Sent EAP Request/Identity Packets TX ReqId

EAP Request/Challenge Packets TX Req

EAP Success Packets n/a

Fail Packets n/a

Received EAPOL Start Packets RX Start

EAPOL Logoff Packets RX Logoff

EAP Response/Identity Packets RX RespId

EAP Response/Challenge Packets RX Resp

Error Packets RX Errors

Controlled User(s) amount n/a



2-56

Display Commandsdisplay dot1x [interface …]

display dot1x [interface …]display dot1x sessions [interface …]display dot1x statistics [interface …]

Displays information about 802.1X.

HP Switch# display dot1xEquipment 802.1X protocol is CHAP authentication is n/a Proxy trap checker is n/a Proxy logoff checker is n/a EAD quick deploy is n/a Configuration: Transmit Period 30 s, Handshake Period n/a Quiet Period 60 s, Quiet Period Timer is n/a Supp Timeout 30 s, Server Timeout 300 s Reauth Period 3600 s The maximal retransmitting times 2 EAD quick deploy configuration: EAD timeout: n/a The maximum 802.1X user resource number is n/a per slot Total current used 802.1X resource number is n/a A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Periodic reauthentication is disabled The port is not an authenticator Authentication Mode is Auto Port Control Type is n/a 802.1X Multicast-trigger is n/a Mandatory authentication domain: n/a Guest VLAN: 0 Auth-Fail VLAN: n/a Max number of on-line users is 0 EAPOL Packet: Tx n/a, Rx n/a Sent EAP Request/Identity Packets : 0


display dot1x [interface ...]display dot1x sessions [interface ...]display dot1x statistics [interface ...]

show dhcp-snooping binding


2-57

Display Commandsdisplay dot1x statistics [interface …]

EAP Request/Challenge Packets: 0 EAP Request/Challenge Packets: 0 Received EAPOL Start Packets : 0 EAPOL LogOff Packets: 0 EAP Response/Identity Packets : 0 EAP Response/Challenge Packets: 0 Error Packets: 0 Controlled User(s) amount to n/a

HP Switch# display dot1x sessions Equipment 802.1X protocol is enabled CHAP authentication is n/a The maximum 802.1X user resource number is n/a per slot Total current used 802.1X resource number is n/a A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Controlled User(s) amount to n/a A2 is link-down 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Controlled User(s) amount to n/a A3 is link-down 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a Controlled User(s) amount to n/a

HP Switch# display dot1x sessionsEquipment 802.1X protocol is enabled CHAP authentication is n/a The maximum 802.1X user resource number is n/a per slot Total current used 802.1X resource number is n/a A1 is link-up 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a


2-58

Display Commandsdisplay dot1x statistics [interface …]

Handshake secure is n/a 802.1X unicast-trigger is n/a EAPOL Packet: Tx n/a, Rx n/a Sent EAP Request/Identity Packets : 0 EAP Request/Challenge Packets: 0 EAP Request/Challenge Packets: 0 Received EAPOL Start Packets : 0 EAPOL LogOff Packets: 0 EAP Response/Identity Packets : 0 EAP Response/Challenge Packets: 0 Error Packets: 0 Controlled User(s) amount to n/a A2 is link-down 802.1X protocol is disabled Proxy trap checker is n/a Proxy logoff checker is n/a Handshake is n/a Handshake secure is n/a 802.1X unicast-trigger is n/a EAPOL Packet: Tx n/a, Rx n/a Sent EAP Request/Identity Packets : 0 EAP Request/Challenge Packets: 0 EAP Request/Challenge Packets: 0 Received EAPOL Start Packets : 0 EAPOL LogOff Packets: 0 EAP Response/Identity Packets : 0 EAP Response/Challenge Packets: 0 Error Packets: 0 Controlled User(s) amount to n/a


HP Switch# show dhcp-snooping binding

MacAddress IP VLAN Interface Time left----------------- -------- ----- --------- ---------22.22.22.22.22.22 10.0.0.1 4 B2 1600

Operating Notes




2-59

Display Commandsdisplay environment

display environment

Displays the temperature information, including the current temperature and temperature thresholds of cards.

HP Switch# display environmentSystem temperature information (degree centigrade)---------------------------------------------------------Slot Sensor Temperature LowerLimit WarningLimit AlarmLimit ShutdownLimitn/a Sys-1 29C n/a 57C n/a n/a

Field Descriptions:

Slot: Slot number of the card (standalone mode); slot number of a card on the specified member switch in the format of member ID/slot number (IRF mode)

Sensor: Temperature sensor:

• hotspot: Hotspot temperature sensor

• inflow: Inflow temperature sensor

• outflow: Outflow temperature sensor

Temperature: Current temperature

Lower limit: Lower limit of temperature

WarningLimit: Upper limit of temperature for warning

AlarmLimit: Upper limit of temperature for alarming

ShutdownLimit: Upper limit of temperature for shutting down the switch (currently not supported)


HP Switch# show system temperature

System Air Temperatures

# |Current Temp | Max Temp | Min Temp | Threshold | OverTemp------+------------+----------+---------+-----------+--------Sys-1 | 31C | 37C | 29C | 57C | NO




display environment show system temperature


2-60

Display Commandsdisplay fan

display fan

Displays the operating state of built-in fans.

HP Switch# display fanFan 1 State: Fan Ok


HP Switch(config)# show system fansFan InformationNum | State | Failures-------+-------------+----------Sys-1 | Fan OK | 00 / 1 Fans in Failure State0 / 1 Fans have been in Failure State

Operating Notes

ProVision uses HP format for printing the fan state.




display fan show system fans


2-61

Display Commandsdisplay fips status

display fips status

Displays FIPS state. By default, the FIPS mode is disabled.

HP Switch# display fips status

FIPS mode is disabled

or

HP Switch# display fips status

FIPS mode is enabled


HP Switch# show secure-mode

Level: Standard

or

HP Switch# show secure-mode

Level: Enhanced

For more information, see the latest Access Security Guide for your switch.



display fips status show secure-mode


2-62

Display Commandsdisplay garp statistics interface <port_list>

display garp statistics interface <port_list>

Displays GVRP transmitted, received and discarded frames in a specified VLAN on a port.

HP Switch# display garp statistics interface a2

GARP statistics on port A2 Number of GVRP Frames Received : 79 Number of GVRP Frames Transmitted : 67 Number of Frames Discarded : 0


HP Switch# show gvrp

GVRP support

Maximum VLANs to support [256] : 256Primary VLAN : DEFAULT_VLANGVRP Enabled [No] : Yes

Port Type | Unknown VLAN Join Leave Leaveall---- -------- + ------------ ----- ----- --------1 10/100TX | Learn 20 300 10002 10/100TX | Learn 20 300 10003 10/100TX | Learn 20 300 10004 10/100TX | Learn 20 300 10005 10/100TX | Learn 20 300 10006 10/100TX | Learn 20 300 1000. . . . . .

For more information, see the latest Advanced Traffic Management Guide for your switch.



display garp statistics interface <port_list> show gvrp


2-63

Display Commandsdisplay garp timer interface <port_list>

display garp timer interface <port_list>

Display GARP timer in a specified port.

HP Switch# display garp timer interface a2

GARP timers on port A2 Garp Join Time : 20 centisecounds Garp Leave Time : 300 centisecounds Garp LeaveAll Time : 1000 centisecounds Garp Hold Time : (n/a)



GVRP support



Operating Notes

Depending on the device, ProVision displays port numbers as A1, B1, etc. or 1,2, etc. or 1/1, 2/1, etc.

Any display output field not supported in Provsion is displayed as n/a.




display garp timer interface<port_list> show gvrp


2-64

Display Commandsdisplay gvrp state interface <port_list> vlan <vlan-id>

display gvrp state interface <port_list> vlan <vlan-id>

Displays GVRP state machines in a specified VLAN on a port.

HP Switch# display gvrp state interface a2 vlan 2

GVRP state of VLAN 2 on port a2 Applicant state machine : QA Registrar state machine : MTR

Field Descriptions:

Applicant state machine: The Applicant state machine handles attribute decla-rations. Its state can be VA, AA, QA, LA, VP, AP, QP, VO, AO, QO, LO, VON, AON, and QON. Each state consists of two or three letters with the following meanings:

• The first letter indicates the state: V for Very anxious, A for Anxious, Q for Quiet, and L for Leaving.

• The second letter indicates the membership state: A for Active mem-ber, P for Passive member, O for Observer.

• The third letter N (if any) stands for Non-participant.

For example, VP indicates “Very anxious, Passive member".

Registrar state machine: The Registrar state machine records the registration of attributes declared by other participants. Its state can be INN, LV, L3, L2, L1, MT, INR, LVR, L3R, L2R, L1R, MTR, INF, LVF, L3F, L2F, L1F, and MTF. Each state consists of two or three letters/numbers with the following meanings:

• The first two letters/numbers indicate the state: IN stands for In; LV, L3, L2, and L1 all stand for Leaving, and L3, L2, L1 are three sub-states of LV; MT stands for Empty

• The third letter indicates the registration mode: N (or the third letter being absent) for normal registration, R for Registration fixed, and F for Registration forbidden.

For example, MTR stands for “Empty, Registration fixed", indicating the fixed registration mode in Empty state.


display gvrp state interface <port_list> vlan <vlan-id>

show gvrp


2-65

Display Commandsdisplay gvrp state interface <port_list> vlan <vlan-id>



GVRP support






2-66

Display Commandsdisplay gvrp statistics

display gvrp statistics

Displays the GVRP statistics of all tagged ports.

HP Switch# display gvrp statistics GVRP statistics on port A1 GVRP Status : Disabled GVRP Running : YES GVRP Failed Registrations : n/a GVRP Last Pdu Origin : n/a GVRP Registration Type : Normal

Field Descriptions:

GVRP Status: Indicates whether GVRP is enabled or disabled

GVRP Running: Indicates whether GVRP is running

GVRP Failed Registrations: Indicates the number of GVRP registration failures

GVRP Last Pdu Origin: Indicates the source MAC address in the last GVRP PDU

GVRP Registration Type: Indicates the GVRP registration mode (fixed, forbid-den, or normal) on the port


HP Switch# show gvrp GVRP support Maximum VLANs to support [256] : 256Primary VLAN : DEFAULT_VLANGVRP Enabled [No] : Yes

Port Type | Unknown VLAN Join Leave Leaveall---- -------- + ------------ ----- ----- --------1 10/100TX | Learn 20 300 10002 10/100TX | Learn 20 300 10003 10/100TX | Learn 20 300 10004 10/100TX | Learn 20 300 10005 10/100TX | Learn 20 300 10006 10/100TX | Learn 20 300 1000. . . . . .For more information, see the latest Advanced Traffic Management Guide for your switch.



display gvrp statistics show gvrp


2-67

Display Commandsdisplay gvrp status

display gvrp status

Displays the global enable/disable state of GVRP.

HP Switch# display gvrp status

GVRP is enabled

Operating Notes

To enable and control GVRP operation in ProVision software, use the follow-ing commands:

gvrp

interface < port-list > unknown-vlans < learn | block | disable >

ProVision software also supports GVRP configuration and status monitoring by using the Menu interface. For more on GVRP operation, refer to the chapter titled “GVRP” in the latest Advanced Traffic Management Guide for your switch.


GVRP disabled:


GVRP support

Maximum VLANs to support [256] : 256 Primary VLAN : DEFAULT_VLAN GVRP Enabled [No] : No

GVRP enabled:


GVRP support

Maximum VLANs to support [256] : 256 Primary VLAN : DEFAULT_VLAN GVRP Enabled [No] : Yes


display gvrp status show gvrp


2-68

Display Commandsdisplay gvrp status

Port Type | Unknown VLAN Join Leave Leaveall ---- --------- + ------------ ----- ----- -------- A1 100/1000T | Learn 20 300 1000 A2 100/1000T | Learn 20 300 1000 A3 100/1000T | Learn 20 300 1000 . . . A24 100/1000T | Learn 20 300 1000



2-69

Display Commandsdisplay gvrp vlan-operation interface interface-type interface-number

display gvrp vlan-operation interface interface-type interface-number

Displays information about dynamic VLAN operations on a port.

HP Switch# display gvrp vlan-operation interface a3

Dynamic VLAN operations on port A3

Operations of creating VLAN : none Operations of deleting VLAN : none Operations of adding VLAN to TRUNK : none Operations of deleting VLAN from TRUNK : none



display gvrp vlan-operation interface interface-type interface-number



2-70

Display Commandsdisplay history-command

display history-command

Displays the last 25 commands executed on the switch CLI, including commands entered incorrectly. The command listing begins with the oldest command in the sequence and ends with the most recent command executed (excluding the display history-command itself).

HP Switch# display history-command 25 display dns domain 24 display gvrp status 23 display gvrp status 22 gvrp helpp 21 gvrp help 20 gvrp 19 display gvrp status . . . 2 display ip community-list 1 display ip as-path

Operating Notes

The ProVision software show history command output is identical to the Com-ware display history-command output.



display history-command show history


2-71

Display Commandsdisplay hwtacacs

display hwtacacs

Displays the configuration information or statistics of HWTACACS schemes. This command is available only in manager mode.

HP Switch# display hwtacacs

------------------------------------------------------------- HWTACACS-server template name : n/a Primary-authentication-server : 1.2.3.4:n/a VPN instance : n/a Primary-authorization-server : 1.2.3.4:n/a VPN instance : n/a Primary-accounting-server : 1.2.3.4:n/a VPN instance : n/a Secondary-authentication-server : 6.7.8.9:n/a VPN instance : n/a Secondary-authorization-server : 6.7.8.9:n/a VPN instance : n/a Secondary-accounting-server : 6.7.8.9:n/a VPN instance : n/a Current-authentication-server : 1.2.3.4:n/a VPN instance : n/a Current-authorization-server : 1.2.3.4:n/a VPN instance : n/a Current-accounting-server : 1.2.3.4:n/a VPN instance : n/a Nas-IP address : n/a key authentication : authentication key authorization : authentication key accounting : authentication Nas-IP address : n/a VPN instance : n/a Quiet-interval(min) : n/a Realtime-accounting-interval(min) : n/a Response-timeout-interval(sec) : 5 Acct-stop-PKT retransmit times : n/a Username format : n/a Data traffic-unit : n/a Packet traffic-unit : n/a------------------------------------------------------------- Total 1 HWTACACS scheme(s).


display hwtacacs show tacacs


2-72

Display Commandsdisplay hwtacacs


HP Switch# show tacacs

Status and Counters - TACACS Information

Timeout : 5Source IP Selection : Configured IP InterfaceEncryption Key :

Operating Notes

For more information, refer to the latest Basic Operation Guide for your switch.



2-73

Display Commandsdisplay igmp group

display igmp group

Displays IGMP group address, uptime, and expiry information. If no IGMP groups are detected, returns the system prompt.

HP Switch# display igmp group Total 1 IGMP Group(s). Interface group report information Vlan-interface1(15.255.134.111): Total 1 IGMP Group reported Group Address Last Reporter UpTime Expires 10.255.215.190 10.125.103.197 00:04:22 00:03:38

Field Descriptions

Vlan-interfaceN: IP address of a VLAN on which IGMP is running.

Group Address: Multicast group address.

Last Reporter: Address of the last host that reported its membership for this multicast group.

UpTime: Length of time since the multicast group was reported.

Expires: Remaining time of the multicast group, where “off” means that the multicast group never times out.

Operating Notes

To enable IGMP operation in ProVision software, use the following command from the context of a VLAN on which you want to enable IGMP:

ip igmp

For more on IGMP operation in ProVision software, refer to the chapter titled “Multimedia Traffic Control with IP Multicast (IGMP)” in the latest Multicast

and Routing Guide for your switch.


display igmp group show ip igmp groups


2-74

Display Commandsdisplay igmp group


IGMP Field Mappings.


HP Switch# show ip igmp groups

IGMP Group Address Information

VLAN ID Group Address Expires UpTime Last Reporter | Type ------- --------------- ------------- ------------- --------------- + ------ 1 10.255.215.190 0h 0m 27s 1h 22m 37s 10.125.103.197 | Filter


Vlan-interfaceN VLAN ID

Group Address Group Address

Expires Expires

Uptime UpTime

Last Reporter Last Reporter

n/a Type


2-75

Display Commandsdisplay igmp group interface vlan-interface <vlan-id>

display igmp group interface vlan-interface <vlan-id>

Displays information about dynamically joined IGMP multicast groups.

HP Switch# display igmp group interface vlan-interface 30Vlan-interface30(75.1.30.1): Total 5 IGMP Groups reported Group Address Last Reporter UpTime Expires 239.1.1.1 75.1.30.10 5d 17:48:41 00:03:13 239.1.1.2 75.1.30.10 5d 17:48:41 00:03:13 239.1.1.3 75.1.30.10 5d 17:48:41 00:03:13 239.1.1.4 75.1.30.10 5d 17:48:41 00:03:13 239.1.1.5 75.1.30.10 5d 17:48:41 00:03:13

Field Descriptions:

Group: Multicast group address

Last reporter: Address of the last host that reported its membership for this multicast group

Uptime: Length of time since the multicast group was reported

Expires: Remaining time of the multicast group


HP Switch# show ip igmp vlan 30

IGMP Service Protocol Info

Total VLANs with IGMP enabled : 2 Current count of multicast groups joined : 5

IGMP Filter Unknown Multicast: Disabled IGMP Filter Unknown Multicast Status: Disabled

VLAN ID : 30 VLAN Name : VLAN30 IGMP version : 2 Querier Address [this switch] : 75.1.30.1


display igmp group interface vlan-interface <vlan-id>

show ip igmp vlan <vid>


2-76

Display Commandsdisplay igmp group interface vlan-interface <vlan-id>

Querier Port : Querier UpTime : 5d 18h 28m 35s Querier Expiration Time : 0h 0m 6s

Active Group Addresses Type Expires Ports Reports Queries---------------------- ---- ------- ----- -------- -------- 239.1.1.1 Filter 0h 2m 28s A2 3956 0 239.1.1.2 Filter 0h 2m 28s A2 3956 0 239.1.1.3 Filter 0h 2m 27s A2 3956 0 239.1.1.4 Filter 0h 2m 27s A2 3956 0 239.1.1.5 Filter 0h 2m 27s A2 3956 0

Operating Notes

Comware displays a list of configured vlans in the tab help. ProVision does not display dynamic help text such as this.

Comware displays an error for Invalid vlan interface. ProVision accepts the input, a validation is done later and an error is displayed.

For more information, see the latest Multicast and Routing Guide for your switch.



2-77

Display Commandsdisplay igmp group interface vlan-interface <vlan-id> static

display igmp group interface vlan-interface <vlan-id> static

Displays information regarding statically joined IGMP multicast groups.

HP Switch# display igmp group interface Vlan-interface 400 staticStatic join group information of VPN-Instance: public net Total 21 entries Total 6 entries matched

Group Address Source Address Expires 225.1.4.6 0.0.0.0 never 239.4.4.1 0.0.0.0 never 239.4.4.2 0.0.0.0 never 239.4.4.3 0.0.0.0 never 239.4.4.4 0.0.0.0 never 239.4.5.6 0.0.0.0 never

Field Descriptions:

igmp: IGMP status and configuration information

group: Information about group members

interface: Specify interface

Vlan-interface: VLAN interface

VLAN-ID: VLAN interface

static: Static group information



display igmp group interface vlan-interface static



2-78

Display Commandsdisplay igmp group interface vlan-interface <vlan-id> verbose

display igmp group interface vlan-interface <vlan-id> verbose

Displays detailed information about IGMP multicast groups in a particular interface.

HP Switch# display igmp group interface Vlan-interface 400 verbose Vlan-interface400(192.168.9.2): Total 5 IGMP Groups reported Group: 225.1.5.4 Uptime: 00:07:19 Expires: 00:01:43 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.4.4.4 Uptime: 00:07:19 Expires: 00:01:38 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.9.9.9 Uptime: 00:07:19 Expires: 00:01:37 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.9.99.99 Uptime: 00:07:19 Expires: 00:01:41 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.99.99.99 Uptime: 00:07:19 Expires: 00:01:37 Last reporter: 192.168.9.9


display igmp group interface vlan-interface <vlan-id> verbose



2-79

Display Commandsdisplay igmp group interface vlan-interface <vlan-id> verbose

Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off



2-80

Display Commandsdisplay igmp group port-info

display igmp group port-info

Displays Layer 2 port information of IGMP groups, including both dynamic and static Layer 2 port entries.

Field Descriptions

Total 1 IP Group(s): Total number of IP multicast groups.

Total 1 IP Source(s): Total number of IP multicast sources.

Total 1 MAC Group(s): Total number of MAC multicast groups.


display igmp group port-info vlan <vid> show ip igmp vlan <vid>

HP Switch# display igmp group port-info vlan 5 Total 2 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s).

Port flags: D-Dynamic port, S-Static port, C-Copy port Subvlan flags: R-Real VLAN, C-Copy VLAN Vlan(id):5. Total 2 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s). Router port(s):total 2 port(s). F23 (D) F24 (D) IP group(s):the following ip group(s) match to one mac group. IP group address:239.4.4.4 (0.0.0.0, 239.4.4.4): Host port(s):total 1 port(s). F23 (D) MAC group(s): MAC group address: n/a Host port(s):total n/a port(s). IP group(s):the following ip group(s) match to one mac group. IP group address:239.14.14.14 (0.0.0.0, 239.14.14.14): Host port(s):total 1 port(s). F23 (D) MAC group(s): MAC group address: n/a Host port(s):total n/a port(s).


2-81


Port flags: D-Dynamic port, S-Static port, C-Copy port: Port flags: D for a dynamic port, S for a static port, and C for a port copied from a (*, G) entry to an (S, G) entry.

Subvlan flags: R-Real VLAN, C-Copy VLAN: Sub-VLAN flags: R for a real egress sub-VLAN under the current entry, and C for a sub-VLAN copied from a (*, G) entry to an (S, G) entry.

Router port(s): Number of router ports.

Router port unit board: Mask indicating a board with a router port residing on it.

(hh:mm:ss): Remaining time of the aging timer for the dynamic member port or router port:

• In standalone mode, to display the remaining life of a non-aggregation port that does not belong to the main board, you must specify the number of the slot where the corresponding card resides by using slot slot-number. This is not required for an aggregation port.

• In IRF mode, to display the remaining life of a non-aggregation port that does not belong to the main board, you must specify the member ID of the IRF member device and the slot number of the card with chassis chassis-number slot slot-number. For an aggregation port, you do not need to do this.

Operating Notes

Since ProVision switches do not need anything to be configured globally to enable igmp, no error message is displayed for a display command if igmp is not enabled. For more information on IGMP operation, see the “Multimedia Traffic Control with IP Multicast (IGMP)” chapter in the latest Advanced

Traffic Management Guide for your switch.


2-82



display igmp group port-info Field Mappings.


HP Switch(config)# show ip igmp vlan 1


Total VLANs with IGMP enabled : 30 Current count of multicast groups joined : 20 VLAN ID : 2 VLAN Name : VLAN2 IGMP version : 2 Querier Address : 10.255.128.2 Querier Port : A1 Querier UpTime : 1h 51m 59s Querier Expiration Time : 2min 5sec Ports with multicast routers: A1, A5-A6

Active Group Addresses Type Expires Ports Reports Queries ---------------------- ---------- --------------- ---------- ------- ------- 226.0.6.7 Filter 2min 5sec A1 10 10 226.0.6.8 Standard 3min 20sec A2 20 20


Total 1 IP Group(s) n/a

Total 1 IP Source(s) n/a

Total 1 MAC Group(s) n/a

Port Flags n/a

Subvlan Flags n/a

Router port(s) Ports with multicast routers

(hh:mm:ss) Querier Expiration Time

IP group address Active Group Addresses

MAC group address n/a

Attribute n/a

Host port unit board n/a

Host port(s) n/a


2-83

Display Commandsdisplay igmp group static

display igmp group static

Displays the information regarding statically joined IGMP multicast groups.

HP Switch# display igmp group static

Static join group information

Total 19 entries

Group Address Source Address Interface Expires 225.1.1.1 0.0.0.0 Vlan1 never 225.1.1.5 0.0.0.0 Vlan1 never 225.1.4.1 0.0.0.0 Vlan4 never 225.1.5.4 0.0.0.0 Vlan5 never 225.4.4.1 0.0.0.0 Vlan4 never 225.4.4.2 0.0.0.0 Vlan4 never 225.4.4.3 0.0.0.0 Vlan4 never 225.4.4.4 0.0.0.0 Vlan4 never 225.5.5.1 0.0.0.0 Vlan5 never 225.5.5.2 0.0.0.0 Vlan5 never 225.5.5.3 0.0.0.0 Vlan5 never 225.5.5.4 0.0.0.0 Vlan5 never 225.5.5.5 0.0.0.0 Vlan5 never 225.44.46.46 0.0.0.0 Vlan1 never 225.44.46.46 0.0.0.0 Vlan4 never 225.44.46.46 0.0.0.0 Vlan5 never 225.145.145.145 0.0.0.0 Vlan1 never 225.145.145.145 0.0.0.0 Vlan4 never 225.145.145.145 0.0.0.0 Vlan5 never

Field Descriptions:





IGMP Service Protocol InfoTotal VLANs with IGMP enabled : 30


display igmp group static show ip igmp vlan <vid>


2-84

Display Commandsdisplay igmp group static

Current count of multicast groups joined : 20VLAN ID : 2VLAN Name : VLAN2IGMP version : 2Querier Address : 10.255.128.2Querier Port : A1Querier UpTime : 1h 51m 59sQuerier Expiration Time : 2min 5secPorts with multicast routers: A1, A5-A6

Active Group Addresses Type Expires Ports Reports Queries---------------------- ----- ------- ----- -------- -------226.0.6.7 Filter 2min 5sec A1 10 10226.0.6.8 Standard 3min 20sec A2 20 20




2-85

Display Commandsdisplay igmp group verbose

display igmp group verbose

Displays detailed information about IGMP multicast groups.HP Switch# display igmp group verboseInterface group report information Vlan-interface400(192.168.9.2): Total 5 IGMP Groups reported Group: 225.1.5.4 Uptime: 00:00:16 Expires: 00:01:54 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.4.4.4 Uptime: 00:00:16 Expires: 00:01:54 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.9.9.9 Uptime: 00:00:16 Expires: 00:01:54 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.9.99.99 Uptime: 00:00:16 Expires: 00:01:54 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off Group: 239.99.99.99 Uptime: 00:00:16 Expires: 00:01:54 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off



display igmp group verbose No equivalent ProVision software command


2-86

Display Commandsdisplay igmp group x.x.x.x static

display igmp group x.x.x.x static

Displays information regarding statically joined IGMP multicast groups.

HP Switch# display igmp group 225.44.46.46 staticStatic join group information Total 19 entries Total 3 entries matched

Group Address Source Address Interface Expires 225.44.46.46 0.0.0.0 Vlan1 never 225.44.46.46 0.0.0.0 Vlan4 never 225.44.46.46 0.0.0.0 Vlan5 never

Field Descriptions:igmp: IGMP status and configuration information

group: Information about group members

static: Static group information



IGMP Service Protocol InfoTotal VLANs with IGMP enabled : 30Current count of multicast groups joined : 20VLAN ID : 2VLAN Name : VLAN2IGMP version : 2Querier Address : 10.255.128.2Querier Port : A1Querier UpTime : 1h 51m 59sQuerier Expiration Time : 2min 5secPorts with multicast routers: A1, A5-A6

Active Group Addresses Type Expires Ports Reports Queries---------------------- ----- ------- ----- -------- -------226.0.6.7 Filter 2min 5sec A1 10 10226.0.6.8 Standard 3min 20sec A2 20 20




display igmp group x.x.x.x static show ip igmp vlan <vid>


2-87

Display Commandsdisplay igmp group x.x.x.x verbose

display igmp group x.x.x.x verbose

Displays detailed information about a specified IGMP multicast group.

HP Switch# display igmp group 239.4.4.4 verboseInterface group report information Vlan-interface400(192.168.9.2): Total 5 IGMP Groups reported Group: 239.4.4.4 Uptime: 00:01:56 Expires: 00:02:06 Last reporter: 192.168.9.9 Last-member-query-counter: 0 Last-member-query-timer-expiry: off Version1-host-present-timer-expiry: off



display igmp group x.x.x.x verbose No equivalent ProVision software command


2-88

Display Commandsdisplay igmp interface

display igmp interface

Displays IGMP configuration and operation information of the specified inter-face or all IGMP-enabled interfaces.

HP Switch# display igmp interface Interface informationVlan-interface30(75.1.30.1):IGMP is enabled Current IGMP version is 2 Value of query interval for IGMP(in seconds): 125 Value of other querier present interval for IGMP(in seconds): 255 Value of maximum query response time for IGMP(in seconds): 10 Querier for IGMP: 75.1.30.1 (this router) Total 5 IGMP Groups reported

Field Descriptions:

Vlan-interface200 (10.10.1.20): Interface and IP address

Current IGMP version: Version of IGMP currently running on the interface

Value of query interval for IGMP(in seconds): IGMP general query interval, in seconds

Value of other querier present interval for IGMP(in seconds): Other querier present interval, in seconds

Value of maximum query response time for IGMP(in seconds): Maximum response time for IGMP general queries, in seconds

Value of last member query interval(in seconds): IGMP last member query inter-val, in seconds

Value of startup query interval(in seconds): IGMP startup query interval, in seconds

Value of startup query count: Number of IGMP general queries the device sends on startup


display igmp interface show ip igmp vlan <vid>


2-89


General query timer expiry: Remaining time of the IGMP general query timer, where “off” means that the timer never expires

Querier for IGMP: IP address of the IGMP querier

IGMP activity: Statistics of IGMP activities (joins and leaves)

Multicast routing on this interface: Whether the multicast routing and forward-ing function is enabled

Robustness: Robustness variable of the IGMP querier

Require-router-alert: Dropping IGMP messages without Router-Alert (enabled/disabled)

Fast-leave: Fast leave processing status (enabled/disabled)

Ssm-mapping: IGMP SSM mapping status (enabled/disabled)

Startup-query-timer-expiry: Remaining time of the startup query timer, where “off” means that the timer never expires

Other-querier-present-timer-expiry: Remaining time of the other querier present timer, where “off” means that the timer never expires

Proxying interface: IGMP proxy interface, where “none” means that no proxy interface exists

Total 1 IGMP Group reported: Total number of IGMP groups the interface has dynamically joined

IGMP proxy is enabled: IGMP proxying is enabled

Version1-querier-present-timer-expiry: Remaining time of the IGMPv1 querier present timer, where “off” means that the timer never expires

Version2-querier-present-timer-expiry: Remaining time of the IGMPv2 querier present timer, where “off” means that the timer never expires


There is no direct equivalent ProVision command.



Total VLANs with IGMP enabled : 2

Current count of multicast groups joined : 5


2-90


IGMP Filter Unknown Multicast: Disabled

IGMP Filter Unknown Multicast Status: Disabled

VLAN ID : 30

VLAN Name : VLAN30

IGMP version : 2

Querier Address [this switch] : 75.1.30.1

Querier Port :

Querier UpTime : 5d 18h 39m 7s

Querier Expiration Time : 0h 0m 4s

Active Group Addresses Type Expires Ports Reports Queries ---------------------- ---- ------- ------- ------ ------- 239.1.1.1 Filter 0h 2m 25s A2 3961 0 239.1.1.2 Filter 0h 2m 25s A2 3961 0 239.1.1.3 Filter 0h 2m 25s A2 3961 0 239.1.1.4 Filter 0h 2m 25s A2 3961 0 239.1.1.5 Filter 0h 2m 24s A2 3961 0

Operating Notes

ProVision does not support VPN instance.




2-91

Display Commandsdisplay igmp interface verbose

display igmp interface verbose

Displays detailed IGMP configuration and operation information.

HP Switch# display igmp interface verboseInterface information Vlan-interface1(10.100.239.141): IGMP is enabled Current IGMP version is 2 Value of query interval for IGMP(in seconds): 125 Value of other querier present interval for IGMP(in seconds): 255 Value of maximum query response time for IGMP(in seconds): 10 Value of last member query interval(in seconds): 10 Value of startup query interval(in seconds): 31 Value of startup query count: 2 General query timer expiry (hours:minutes:seconds): 00:01:58 Querier for IGMP: 10.100.239.141 (this router) IGMP activity: 378 joins, 0 leaves Multicast routing on this interface: disabled Robustness: 2 Require-router-alert: enabled Fast-leave: enabled Ssm-mapping: n/a Startup-query-timer-expiry: off Other-querier-present-timer-expiry: off Proxying interface: n/a Total 9 IGMP Groups reported

Vlan-interface2(192.168.9.2): IGMP is enabled Current IGMP version is 2 Value of query interval for IGMP(in seconds): 125 Value of other querier present interval for IGMP(in seconds): 255 Value of maximum query response time for IGMP(in seconds): 10 Value of last member query interval(in seconds): 10 Value of startup query interval(in seconds): 31 Value of startup query count: 2 General query timer expiry (hours:minutes:seconds): 00:01:56 Querier for IGMP: 192.168.9.2 (this router) IGMP activity: 0 joins, 0 leaves Multicast routing on this interface: disabled Robustness: 2


display igmp interface verbose No equivalent ProVision software command


2-92

Display Commandsdisplay igmp interface verbose

Require-router-alert: enabled Fast-leave: disabled Ssm-mapping: n/a Startup-query-timer-expiry: off Other-querier-present-timer-expiry: off Proxying interface: n/a



2-93

Display Commandsdisplay igmp interface vlan-interface <vlan-id>

display igmp interface vlan-interface <vlan-id>

Displays the IGMP configuration and operation information of the specified interface or all IGMP-enabled interfaces.

Field Descriptions

Vlan-interface: Interface and IP address.

Current IGMP Version: Version of IGMP currently running on the interface.

Value of query interval for IGMP(in seconds): IGMP general query interval, in seconds.

Value of other querier present interval for IGMP (in seconds): Other querier present interval, in seconds.

Value of maximum query response time for IGMP(in seconds): Maximum response time for IGMP general queries, in seconds.

Querier for IGMP: IP address of the IGMP querier.

Operating Notes

If the VLAN interface is invalid, the switch displays “VLAN <VLAN-ID> not found”.


display igmp interface vlan-interface <vlan-id>

show ip igmp vlan <vid>

HP Switch# display igmp interface vlan-interface 1

Vlan-interface1(10.100.1.238): IGMP is enabled Current IGMP version is 2 Value of query interval for IGMP(in seconds): 125 Value of other querier present interval for IGMP(in seconds): 255 Value of maximum query response time for IGMP(in seconds): 10 Querier for IGMP: 10.100.1.238 (this router) Total 8 IGMP Groups reported


2-94


For more information on switch IGMP operation, see the “Multimedia Traffic Control with IP Multicast (IGMP)” chapter in the latest Advanced Traffic

Management Guide for your switch.


display igmp interface vlan-interface <vlan-id> Field Mappings.

HP Switch(config)# show ip igmp vlan 1


Total VLANs with IGMP enabled : 30 Current count of multicast groups joined : 20 VLAN ID : 2 VLAN Name : VLAN2 IGMP version : 2 Querier Address : 10.255.128.2 Querier Port : A1 Querier UpTime : 1h 51m 59s Querier Expiration Time : 2min 5sec Ports with multicast routers: A1, A5-A6

Active Group Addresses Type Expires Ports Reports Queries ---------------------- ---------- --------------- ---------- ------- ------- 226.0.6.7 Filter 2min 5sec A1 10 10 226.0.6.8 Standard 3min 20sec A2 20 20


Vlan-interface VLAN-ID

Current IGMP Version IGMP version

Value of query interval n/a

Value of other querier n/a

Value of maximum query response time

n/a

Querier for IGMP Querier Address

n/a VLAN Name

n/a Querier Port

n/a Querier UpTime


2-95



Startup-query-timer-expiry Querier Expiration Time

n/a Ports with multicast routers

n/a Active Group Addresses

n/a Type

Startup-query-timer-expiry Expires

n/a Ports

n/a Reports

IGMP activity Queries



2-96

Display Commandsdisplay igmp routing-table

display igmp routing-table

Displays information regarding the IGMP routing table.

HP Switch# display igmp routing-table

Routing tableTotal 5 entries

00001. (*, 239.1.1.1) List of 1 downstream interface Vlan-interface30 (75.1.30.1), Protocol: IGMP





Field Descriptions:

Routing table of VPN-Instance: public net: Public network IGMP routing table

00001: Sequence number of this (*, G) entry

(*, 225.1.1.1): A (*, G) entry of the IGMP routing table

Flag: IGMP route flags:


display igmp routing-table show ip igmp vlan <vid>


2-97

Display Commandsdisplay igmp routing-table

• ACT: Indicates IGMP routing entries that have been used for forward-ing data packets but have the multicast group address out of the SSM group range

• SUC: Indicates IGMP routing entries that have been added to the forwarding table and have the multicast group address within the SSM group range

List of 1 downstream interface: Downstream interface list, namely, the interfaces to which multicast data for this group will be forwarded

in include mode: The downstream interface is in the include mode

in exclude mode: The downstream interface is in the exclude mode

Downstream interface is none: No downstream interfaces exist

Protocol: Protocol type


There is no direct equivalent ProVision command. Please see “show ip igmp vlan <vid>” on page 2-89.



2-98

Display Commandsdisplay interface

display interface

Displays current state about a specified port and related information. If no port number is specified, information is displayed for all ports.

HP Switch# display interface a1 A1 current state: UP IP Packet Frame Type: n/a, Hardware Address: 001560-f9b0ff Description: A1 interface Loopback is n/a Media type is twisted Pair Port hardware type is 100/1000T 1000Mbps-speed mode, full-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled The Maximum Frame Length is 9216 Broadcast MAX-ratio: n/a Unicast MAX-ratio: n/a Multicast MAX-ratio: n/a Jumbo frame: [ see "show jumbos"] PVID : 1 Mdi type: MDIX Link delay is n/a Port link-type: n/a Tagged VLAN ID : none Untagged VLAN ID : 1 Port priority: No-override Last clearing of counters: n/a Peak value of input: n/a Peak value of output: n/a Last 300 seconds input: 0 packets/sec 128846 bytes/sec 0% Last 300 seconds output: 0 packets/sec 65444 bytes/sec 0% Input (total): 0 packets, 26 bytes 3 unicasts, 2 broadcasts, 21 multicasts, 0 pauses Input (normal): 0 packets, 26 bytes 3 unicasts, 2 broadcasts, 21 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, n/a throttles 0 CRC, 0 frame, n/a overruns, n/a aborts n/a ignored, n/a parity errors Output (total): 0 packets, 24 bytes 0 unicasts, 4 broadcasts, 20 multicasts, 0 pauses Output (normal): 0 packets, 24 bytes


display interface show interface <port>


2-99

Display Commandsdisplay interface

0 unicasts, 4 broadcasts, 20 multicasts, 0 pauses Output: 0 output errors, n/a underruns, n/a buffer failures n/a aborts, 0 deferred, 0 collisions, 0 late collisions n/a lost carrier, n/a no carrier


HP Switch# show interfaces briefStatus and Counters - Port Status

| Intrusion MDI Flow BcastPort Type | Alert Enabled Status Mode Mode Ctrl Limit----- ---------+ --------- ------- ------ ---- ---- ---- -----B1 100/1000T | No Yes Down Auto-10-100 Auto off 0B2 100/1000T | No Yes Down 1000FDx Auto off 0B3 100/1000T | No Yes Down 1000FDx Auto off 0B4 100/1000T | No Yes Down 1000FDx Auto off 0B5 100/1000T | No Yes Down 1000FDx Auto off 0B6 100/1000T | No Yes Down 1000FDx Auto off 0

Operating Notes





2-100

Display Commandsdisplay interface brief

display interface brief

Displays brief information about Layer 3 interfaces (tunnels) and Layer 2 interfaces.

Field Descriptions

The brief information of interface(s) under route mode: Brief information about Layer 3 interfaces.

The brief information of interface(s) under bridge mode: Brief information about Layer 2 interfaces.

Link: ADM - administratively down; Stby - standby: Link status:• ADM—The interface has been administratively shut down. To recover

its physical layer state, perform the undo shutdown command.

• Stby—The interface is operating as a backup interface.


display interface brief show interfaces brief

HP Switch(config)# display interface briefThe brief information of interface(s) under route mode:Link: ADM - administratively down; Stby - standbyProtocol: (s) - spoofing Interface Link Protocol Main IP Description tunnel-1 Down UP 20.1.1.1 tunnel1

The brief information of interface(s) under bridge mode:Link: ADM - administratively down; Stby - standbySpeed or Duplex: (a)/A - auto; H - half; F - fullType: A - access; T - trunk; H - hybridInterface Link Speed Duplex Type PVID DescriptionA1 UP auto A n/a 1 port1A2 DOWN auto A n/a 20 port2A3 DOWN auto A n/a 1A4 DOWN auto A n/a 1A5 DOWN auto A n/a 1A6 DOWN auto A n/a 1A7 DOWN auto A n/a 1A8 DOWN auto A n/a 1A9 DOWN auto A n/a 1. ..


2-101


Speed or Duplex: (a)/A - auto; H - half; F - full: If the speed of an interface is automatically negotiated, its speed attribute includes the auto negotiation flag, letter a in parentheses. If the duplex mode of an interface is automatically negotiated, its duplex mode attribute includes the auto negotiation flag, letter a in parentheses or a capital A. Letter H indicates the half duplex mode, and letter F indicates the full duplex mode.

Type: A - access; T - trunk; H - hybrid: Link type options for Ethernet interfaces.

Protocol: (s) - spoofing: If the network layer protocol state of an interface is shown as UP, but its link is an on-demand link or not present, its protocol attribute includes the spoofing flag (an s in parentheses).

Interface: The abbreviated interface name.

Link: The physical link state of the interface.

Speed: The interface speed, in bps.

PVID: The default VLAN ID.

Description: Name of the interface.

Operating Notes

For more information on interface statistics, see the “Port Status and Config-uration” chapter in the latest Management and Configuration Guide for your switch.


2-102



display interface brief Field Mappings.


HP Switch(config)# show interfaces brief

Status and Counters - Port Status

| Intrusion MDI Flow Bcast Port Type | Alert Enabled Status Mode Mode Ctrl Limit ------ --------- + --------- ------- ------ ---------- ---- ---- ----- A1 10GbE-T | No Yes Up 1000FDx MDIX off 0 A2 10GbE-T | No Yes Down 10GigFD MDI off 0 A3 10GbE-T | No Yes Down 10GigFD MDIX off 0 A4 10GbE-T | No Yes Down 10GigFD Auto off 0 A5 10GbE-T | No Yes Down 10GigFD Auto off 0 A6 10GbE-T | No Yes Down 10GigFD Auto off 0 A7 10GbE-T | No Yes Down 10GigFD Auto off 0 A8 10GbE-T | No Yes Down 10GigFD Auto off 0


interfaces under route mode n/a

interfaces under bridge mode n/a

Link status Status

Speed or Duplex Mode/MDI Mode

Type n/a

Protocol n/a

Interface Port

Link Status

Speed Type

PVID n/a

Description n/a

n/a Intrusion Alert

n/a Bcast Limit


2-103

Display Commandsdisplay interface brief down

display interface brief down

Displays information about interfaces in down state and the relevant causes.

Field Descriptions

The brief information of interface(s) under route mode: Brief information about Layer 3 interfaces.

The brief information of interface(s) under bridge mode: Brief information about Layer 2 interfaces.

Link: ADM - administratively down; Stby - standby: Link status:• ADM—The interface has been administratively shut down. To recover

its physical layer state, perform the undo shutdown command.

• Stby—The interface is operating as a backup interface.

Interface: Interface number.

Link Cause: Displays information about interfaces in the down state and the causes.


display interface brief down show interfaces brief

HP Switch(config)# display interface brief downThe brief information of interface(s) under route mode:Link: ADM - administratively down; Stby - standbyInterface Link Cause tunnel-1 Down n/a

The brief information of interface(s) under bridge mode:Link: ADM - administratively down; Stby - standbyInterface Link Cause A2 Down Not connected A3 Down Not connected A4 Down Not connected A5 Down Not connected A6 Down Not connected A7 Down Not connected . . .


2-104

Display Commandsdisplay interface brief down

Operating Notes

For the interfaces under route mode, only “interface tunnels” are displayed; other types are not supported.

H3C displays one of the reasons for the field “Cause” if the port is down: Not connected, Administratively, Link-Aggregation interface down, OAM connec-tion failure, DLDP connection failure, Loopback detection-protected, BPDU-protected, Monitor-Link uplink down.

ProVision doesn’t support OAM and DLDP.

For more information, see the “Port Status and Configuration” chapter in the latest Management and Configuration Guide for your switch.


display interface brief down Field Mappings.


HP Switch(config)# show interfaces brief

Status and Counters - Port Status

| Intrusion MDI Flow Bcast Port Type | Alert Enabled Status Mode Mode Ctrl Limit ------ --------- + --------- ------- ------ ---------- ---- ---- ----- A1 10GbE-T | No Yes Up 1000FDx MDIX off 0 A2 10GbE-T | No Yes Down 10GigFD MDI off 0 A3 10GbE-T | No Yes Down 10GigFD MDIX off 0 A4 10GbE-T | No Yes Down 10GigFD Auto off 0 A5 10GbE-T | No Yes Down 10GigFD Auto off 0 A6 10GbE-T | No Yes Down 10GigFD Auto off 0 A7 10GbE-T | No Yes Down 10GigFD Auto off 0 A8 10GbE-T | No Yes Down 10GigFD Auto off 0


interfaces under route mode n/a

interfaces under bridge mode n/a

Interface Port

Link Cause Status


2-105

Display Commandsdisplay ip as-path

display ip as-path

Displays BGP AS-Path list information

HP Switch# display ip as-path ListID Mode Expression test1 permit $25

Field Descriptions

ListID: AS path list ID.

Mode: Match mode — permit or deny.

Expression: Regular expression for matching.

Operating Notes

To enable BGP operation in ProVision software, see the “BGP (Border Gate-way Protocol)” chapter in the latest Multicast and Routing Guide for your switch.


HP Switch# show ip aspath-list

Route Policy AS-path List test1: 1 entries seq 5 permit "$25" ip as-path Field Mappings



display ip as-path show ip aspath-list


ListID as-path name

Mode permit or deny

Expression $ expression


2-106

Display Commandsdisplay ip check source

display ip check source

Displays display dynamic IP source guard binding entries.

Field Descriptions

Total entries found: Total number of found entries

MAC Address: MAC address of the dynamic IP source guard binding entry. N/A means that no MAC address is bound in the entry.

IP Address: IP address of the dynamic IP source guard binding entry. N/A means that no IP address is bound in the entry.

VLAN: VLAN bound to the IP source guard binding entry. N/A means that no VLAN is bound in the entry.

Interface: Interface of the dynamic IP source guard binding entry.

Type: Type of the dynamic IP source guard binding entry, including:

• DHCP-SNP—DHCP snooping entry.

• DHCP-RLY—DHCP relay entry.

• DHCPv6-SNP—DHCPv6 snooping entry.

• ND-SNP—ND snooping entry.

Operating Notes

For more information about DHCP snooping, see the “Configuring Advanced Threat Protection” chapter in the latest Access Security Guide for your switch.


display ip check source show dhcp-snooping bindings

HP Switch# display ip check source

Total entries found: 3 MAC Address IP Address VLAN Interface Status 005056-9f2c8b 192.168.1.1 1 n/a Dynamic 005056-9f2c9b 192.167.1.1 1 n/a Dynamic 005056-9f2c9b 192.167.0.1 2 n/a Dynamic


2-107

Display Commandsdisplay ip check source


display ip check source Field Mappings.



Total entries found n/a

MAC Address n/a

IP Address n/a

VLAN n/a

Interface n/a

Type n/a

HP Switch(config)# show dhcp-snooping

DHCP Snooping Information

DHCP Snooping : Yes

Enabled Vlans :

Verify MAC : Yes

Option 82 untrusted policy : drop

Option 82 Insertion : Yes

Option 82 remote-id : mac

Store lease database : Not configured

Port Trust

----- -----

B1 No

B2 No


2-108

Display Commandsdisplay ip community-list

display ip community-list

Displays BGP community list information HP Switch# display ip community-list Community List Number community-1 permit 10

deny 50

Field Descriptions

Community List Number < community-name >: Specifies the community being reported.

permit: Permitted routes that belong to the community .

deny: Denied routes that belong to the community.

Operating Notes

To enable BGP in ProVision software, see the “BGP (Border Gateway Proto-col)” chapter in the latest Multicast and Routing Guide for your switch.


HP Switch# show ip community-list

ip community list community-1 standard permit 10 deny 50

ip as-path Field Mappings.



display ip community-list show ip community-list


Community List Number ip community list

permit permit

deny deny


2-109

Display Commandsdisplay ip http

display ip http

Displays information about HTTP.

HP Switch# display ip httpHTTP port: 80Basic ACL: n/aCurrent connection: 0Operation status: enabled



display ip http No equivalent ProVision software command


2-110

Display Commandsdisplay ip https

display ip https

Displays information about HTTPs.

HP Switch# display ip httpsHTTPS port: 443SSL server policy: n/aCertificate access-control-policy: n/aBasic ACL: n/aOperation status: disabled



display ip https No equivalent ProVision software command


2-111

Display Commandsdisplay ip ip-prefix

display ip ip-prefix

Displays all the prefix list information, including list name, address, length, rule type, ge and le [greater than or equal /less than or equal w.r.t mask range] for a specific network. This command is available only in manager mode.

HP Switch# display ip ip-prefix abc Prefix-list abc Permitted n/a Denied n/a index: 5 permit 11.2.3.4/8 ge 8 le 8


HP Switch# show ip prefix-list

ip prefix-list Odd: 4 entriesseq 5 permit 10.1.1.1/24 ge 24 le 24seq 10 deny 10.1.2.1/24 ge 24 le 24seq 15 permit 10.1.3.1/24 ge 24 le 24seq 20 deny 10.1.4.1/24 ge 24 le 24

ip prefix-list Even: 4 entriesseq 5 deny 10.1.1.1/24 ge 24 le 24seq 10 permit 10.1.2.1/24 ge 24 le 24seq 15 deny 10.1.3.1/24 ge 24 le 24seq 20 permit 10.1.4.1/24 ge 24 le 24

Operating Notes

For more information, refer to the latest Multicast and Routing Guide for your switch.



display ip ip-prefix show ip prefix-list


2-112

Display Commandsdisplay ipv6 dhcp duid

display ipv6 dhcp duid

Displays the DUID of the local switch.

Field Descriptions

The DUID of this device: The DHCP for IPv6 Unique Identifier (DUID).

Operating Notes

For more information about IPv6 DHCPv6, see the “DHCPv6-Relay” chapter in the latest IPv6 Configuration Guide for your switch.



display ipv6 dhcp duid No equivalent ProVision software command

HP Switch# display ipv6 dhcp duid

The DUID of this device: 0003-0001-00e0-fc00-5552.


2-113

Display Commandsdisplay ipv6 dhcp relay server-address all

display ipv6 dhcp relay server-address all

Displays all DHCPv6 server address information.

Field Descriptions

Interface: Interface that serves as the DHCPv6 relay agent.

Server address(es): DHCPv6 server address(es) specified on the interface.

Output Interface: Outgoing interface of DHCPv6 packets.

Operating Notes




display ipv6 dhcp relay server-address all show ipv6 helper-address

HP Switch# display ipv6 dhcp relay server-address allInterface: Vlan2Server address(es) Output Interface1::1FF02::1:2 Vlan4 Interface: Vlan3Server address(es) Output Interface1::1FF02::1:2 Vlan4

HP Switch(config)# show ipv6 helper-address

VLAN: 14

IPv6 Helper Address Egress Vlan

---------------------------------------------- -----------

FF05::1:3 14


2-114

Display Commandsdisplay ipv6 dhcp relay server-address all

display ipv6 dhcp relay server-address all Field Mappings.



Interface VLAN

Server address(es) IPv6 Helper Address

Output Interface Egress Vlan


2-115

Display Commandsdisplay ipv6 dhcp relay server-address interface <id>

display ipv6 dhcp relay server-address interface <id>

Displays DHCPv6 server address information of the specified interface.

Field Descriptions

Interface: Interface that serves as the DHCPv6 relay agent.

Server address(es): DHCPv6 server address(es) specified on the interface.

Output Interface: Outgoing interface of DHCPv6 packets.

Operating Notes




display ipv6 dhcp relay server-address interface <id>

show ipv6 helper-address

HP Switch# display ipv6 dhcp relay server-address interface vlan-interface 2Interface: Vlan2Server address(es) Output Interface1::1FF02::1:2 Vlan4

HP Switch(config)# show ipv6 helper-address

VLAN: 14

IPv6 Helper Address Egress Vlan

---------------------------------------------- -----------

FF05::1:3 14


2-116

Display Commandsdisplay ipv6 dhcp relay server-address interface <id>

display ipv6 dhcp relay server-address interface <id> Field Mappings.



Interface VLAN

Server address(es) IPv6 Helper Address

Output Interface Egress Vlan


2-117

Display Commandsdisplay ipv6 dhcp relay statistics

display ipv6 dhcp relay statistics

Displays packet statistics on the DHCPv6 relay agent.

Field Descriptions

Packets dropped: Number of discarded packets.

Error: Number of discarded error packets.

Excess of rate limit: Number of packets discarded due to excess of rate limit.

Packets received: Number of received packets.

SOLICIT: Number of received solicit packets.

REQUEST: Number of received request packets.

CONFIRM: Number of received confirm packets.

RENEW: Number of received renew packets.


displayipv6 dhcp relay statistics show dhcpv6-relay

HP Switch# display ipv6 dhcp relay statisticsPackets dropped : 4 Error : 4 Excess of rate limit : n/aPackets received : 14 SOLICIT : 0 REQUEST : 0 CONFIRM : 0 RENEW : 0 REBIND : 0 RELEASE : 0 DECLINE : 0 INFORMATION-REQUEST : 7 RELAY-FORWARD : 0 RELAY-REPLY : 7Packets sent : 14 ADVERTISE : 0 RECONFIGURE : 0 REPLY : 7 RELAY-FORWARD : 7 RELAY-REPLY : 0


2-118


REBIND: Number of received rebind packets.

RELEASE: Number of received release packets.

DECLINE: Number of received decline packets.

INFORMATION-REQUEST: Number of received information request packets.

RELAY-FORWARD: Number of received relay-forward packets.

RELAY-REPLY: Number of received relay-reply packets.

Packets sent: Number of sent packets.

ADVERTISE: Number of sent advertise packets.

RECONFIGURE: Number of sent reconfigure packets.

REPLY: Number of sent reply packets.

RELAY-FORWARD: Number of sent Relay-forward packets.

RELAY-REPLY: Number of sent Relay-reply packets.

Operating Notes



HP Switch(config)# show dhcpv6-relay

DHCPV6 Relay Agent : Enabled


VLAN Name Received Dropped Failed Received Dropped Failed ---------- ---------- ---------- ---------- ---------- ---------- ---------- DEFAULT... 120 0 0 120 0 0 VLAN20 30 1 0 29 2 1


2-119


display ipv6 dhcp relay statistics Field Mappings.



Packets dropped Dropped

Error Failed

Excess of rate limit n/a

Packets received Received


2-120

Display Commandsdisplay ipv6 routing-table

display ipv6 routing-table

Displays brief ipv6 routing information. The verbose option displays detailed information about the ipv6 routing table.

HP Switch# display ipv6 routing-table Routing Table: Public Destinations: 3 Routes : 3

Destination: ::1/128 Protocol : DirectNextHop : ::1 Preference: 0Interface : InLoop0 Cost : 0

Destination: 6::/64 Protocol : OSPFv3NextHop : FE80::3A22:D6FF:FEB4:4450 Preference: 10Interface : Vlan2 Cost : 2

Destination: 7::/64 Protocol : DirectNextHop : 7::2 Preference: 0Interface : Vlan2 Cost : 0

HP Switch# display ipv6 routing-table verboseRouting Table : Public Destinations : 2 Routes : 2

Destination : ::1 PrefixLength : 128NextHop : ::1 Preference : 0RelayNextHop : n/a Tag : n/aNeighbor : n/a ProcessID : n/aInterface : InLoopBack0 Protocol : DirectState : Active NoAdv Cost : 0Tunnel ID : n/a Label : n/aAge : 28864sec

Destination : 6:: PrefixLength : 64NextHop : FE80::3A22:D6FF:FEB4:4450 Preference : 10RelayNextHop : n/a Tag : n/aNeighbor : n/a ProcessID : n/aInterface : Vlan-interface2 Protocol : OSPFv3State : Active Adv Cost : 2Tunnel ID : n/a Label : n/aAge : 21665sec


display ipv6 routing-table show ipv6 route


2-121

Display Commandsdisplay ipv6 routing-table


HP Switch# show ipv6 route

IPv6 Route Entries

Destination : ::/0Gateway : 2001:db8:e::55:2Type : static Sub-Type : NA Distance : 130 1 Metric : 1

Destination : ::1/128Gateway : lo0Type : connected Sub-Type : NA Distance : 0 Metric : 1

Destination : 2001:db8:1::127/128Gateway : lo6Type : connected Sub-Type : NA Distance : 0 Metric : 1

Destination : 2001:db8:a::/64Gateway : fe80::22:1%vlan22Type : ospf3 Sub-Type : InterArea Distance : 110 Metric : 2

Destination : 2001:db8:b::/64Gateway : VLAN22Type : connected Sub-Type : NA Distance : 0 Metric : 1

Destination : 2001:db8:c::/64Gateway : 2001:db8:e::55:2Type : static Sub-Type : NA Distance : 120 Metric : 1

-- MORE --, next page: Space, next line: Enter, quit: Control-C

Operating Notes

For more information, refer to the latest IPv6 Configuration Guide for your switch.



2-122

Display Commandsdisplay ipv6 routing-table ipv6-address

display ipv6 routing-table ipv6-address

Displays routing information for a specified destination ipv6 address. The verbose option displays detailed information for the specified destination ipv6 address.

HP Switch# display ipv6 routing-table 6::1 64Routing Table : n/aSummary Count : n/a

Destination : 6::/64 Protocol : DirectNextHop : 6::1 Preference : 0Interface : Vlan2 Cost : 1HP Switch# display ipv6 routing-table 6::1 64 verboseRouting Table : n/aSummary Count : n/a Destination : 6:: PrefixLength : 64 NextHop : 6::1 Preference : 0 RelayNextHop : n/a Tag : n/a Neighbor : n/a Process ID : n/a Interface : Vlan-interface2 Protocol : Direct State : n/a Cost : 1 Tunnel ID : n/a Label : n/a Age : n/a


HP Switch# show ipv6 route

IPv6 Route Entries

Destination : ::/0Gateway : 2001:db8:e::55:2Type : static Sub-Type : NA Distance : 130 1 Metric : 1

Destination : ::1/128Gateway : lo0Type : connected Sub-Type : NA Distance : 0 Metric : 1

Destination : 2001:db8:1::127/128Gateway : lo6Type : connected Sub-Type : NA Distance : 0 Metric : 1

Destination : 2001:db8:a::/64Gateway : fe80::22:1%vlan22


display ipv6 routing-table ipv6-address show ipv6 route


2-123

Display Commandsdisplay ipv6 routing-table ipv6-address

Type : ospf3 Sub-Type : InterArea 2 Distance : 110 Metric : 2

Destination : 2001:db8:b::/64Gateway : VLAN22Type : connected Sub-Type : NA Distance : 0 3 Metric : 1

Destination : 2001:db8:c::/64Gateway : 2001:db8:e::55:2Type : static Sub-Type : NA Distance : 120 Metric : 1

-- MORE --, next page: Space, next line: Enter, quit: Control-C

Operating Notes




2-124

Display Commandsdisplay ipv6 routing-table protocol

display ipv6 routing-table protocol

Displays routing information for a specified routing protocol. The routing protocol specified may be static, direct or ospfv3.

HP Switch# display ipv6 routing-table protocol directRouting Table: n/a Destinations: 1 Routes: 1

Destination : ::1/128 Protocol : Direct NextHop : ::1 Preference : 0 Interface : InLoop0 Cost : 1

HP Switch# display ipv6 routing-table protocol direct verboseRouting Table: n/a Destinations: 1 Routes: 1

Destination : ::1 PrefixLength : 128 NextHop : ::1 Preference : 0 RelayNextHop : n/a Tag : n/a Neighbor : n/a Process ID : n/a Interface : InLoopBack0 Protocol : Direct State : Active Adv Cost : 1 Tunnel ID : n/a Label : n/a Age : 37221sec


HP Switch# show ipv6 route static

IPv6 Route Entries

Destination : 2620:a::/64Gateway : 2620:b::22:1Type : static Sub-Type : NA Distance : 1 Metric : 1

Destination : 2620:c::/64Gateway : 2620:e::55:2Type : static Sub-Type : NA Distance : 1 Metric : 1

Operating Notes




display ipv6 routing-table protocol show ipv6 route {connected | static | ospf3}


2-125

Display Commandsdisplay lacp system-id

display lacp system-id

Displays the system ID of the local system. The system LACP priority and the system MAC address comprise the system ID.

HP Switch# display lacp system-id

Actor System ID: 0x2f00, 001871-c42f00

Field Descriptions

Actor System ID: The local system ID, including system LACP priority and system MAC address. In the above example:

■ 0x2f00 = System LACP Priority

■ 001871-c42f00 = System MAC Address

Operating Notes

To enable LACP operation in ProVision software, use the following command from the context of a port interface on which you want to enable LACP:

lacp

For more on LACP operation in ProVision software, refer to the “Port Trunking” chapter in the latest Management and Configuration Guide for your switch.

Example of Related ProVision Software Command Output. The ProVi-sion software includes a list of ports configured for LACP operation, along with some additional data fields.

HP Switch(eth-A13-A14)# show lacp local

LACP Local Information.

System ID: 001871-c42f00

LACP Tx Rx Timer Port Trunk Mode Aggregated Timer Expired ---- ------ -------- ----------- ------ -------- A13 A13 Active Yes Fast No A14 A14 Active Yes Fast No


display lacp system-id show lacp local


2-126

Display Commandsdisplay lacp system-id

lacp system-id Field Mappings.



Actor System ID System ID

n/a Port

n/a Trunk

n/a LACP Mode

n/a Aggregated

n/a Tx Timer

n/a Rx Timer Expired


2-127

Display Commandsdisplay link-aggregation

display link-aggregation

Displays the load-sharing criteria for load-sharing link-aggregation (trunk) groups.

N o t e Link-aggregation in ProVision software is termed port trunking. Load-shar-

ing is termed load-balancing.

When load-balancing is configured as L4-based, the load-sharing mode includes source and destination MAC address, source and destination IP address, and source and destination TCP/UDP port number, as shown below.

HP Switch(config)# display link-aggregation load-sharing mode Layer 4 traffic: destination-mac address, source-mac address, destination-ip address, source-ip address, destination-port, source-port

When load-balancing is configured as L3-based, the load-sharing mode includes source and destination MAC address, and source and destination IP address, as shown below.

HP Switch(config)# display link-aggregation load-sharing mode Layer 3 traffic: destination-mac address, source-mac address destination-ip address, source-ip address

Operating Notes

To enable trunk load-balancing in ProVision software, use the following command in the global configuration context:

trunk < port-list > trkn trunk

trunk-load-balance < L3-based | L4-based >

For more on trunk load-balancing, refer to the “Port Trunking” chapter in the latest Management and Configuration Guide for your switch.



display link-aggregation load-sharing mode n/a


2-128

Display Commandsdisplay link-aggregation member-port

display link-aggregation member-port

Displays the detailed link aggregation information of the specified member ports or all member ports if no port is specified.

For a member port in a static aggregation group, only the port number and operational key are displayed, because the aggregation group is unaware of information about the peer groups.

Field Descriptions

Flags: One-octet LACP state flags field:

• A indicates whether LACP is enabled. 1 for enabled and 0 for disabled.


display link-aggregation member-portdisplay link-aggregation member-port GigabitEthernet <port-number>


HP Switch# display link-aggregation member-port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation, D -- Synchronization, E -- Collecting, F -- Distributing, G -- Defaulted, H -- Expired

1:Aggregation Interface: Trk1Port Number: 1Oper-Key: 1

2:Aggregation Interface: Dyn1Local: Port Number: 2 Port Priority: 32768 Oper-Key: 2 Flag: n/aRemote: System ID: 0x8000, 0000-0000-0000 Port Number: 0 Port Priority: 32768 Oper-Key: 0 Flag: n/aReceived LACP Packets: 0 packet(s)Illegal: 0 packet(s)Sent LACP Packets: 0 packet(s)


2-129

Display Commandsdisplay link-aggregation member-port

• B indicates the timeout control value. 1 for short timeout, and 0 for long timeout.

• C indicates whether the link is considered as aggregatable by the sending system. 1 for true, and 0 for false.

• D indicates whether the link is considered as synchronized by the sending system. 1 for true, and 0 for false.

• E indicates whether the sending system considers that collection of incoming frames is enabled on the link. 1 for true and 0 for false.

• F indicates whether the sending system considers that distribution of outgoing frames is enabled on the link. 1 for true and 0 for false.

• G indicates whether the receive state machine of the sending system is using default operational partner information. 1 for true and 0 for false.

• H indicates whether the receive state machine of the sending system is in the expired state. 1 for true and 0 for false.

If a flag bit is set to 1, the corresponding English letter that otherwise is not output is displayed.

Aggregation Interface: Aggregate interface to which the port belongs.

Port Priority: Aggregation priority of the port.

Oper-key: Operational key.



2-130

Display Commandsdisplay link-aggregation summary

display link-aggregation summary

Displays the summary information of all aggregation groups.

Information about the remote system for a static link aggregation group may be either shown as none or not displayed, because the aggregation group is unaware of information about the peer groups.

Field Descriptions

Aggregation Interface Type: Aggregate interface type:

• BAGG for a Layer 2 aggregate interface.

• RAGG for a Layer 3 aggregate interface.

Aggregation Mode: Aggregation group type:

• S for static link aggregation.

• D for dynamic aggregation.

Loadsharing Type: Loadsharing type:

• Shar for load sharing.

• NonS for non-load sharing.

Actor System ID: Local system ID, which comprises the system LACP priority and the system MAC address.


display link-aggregation summary No equivalent ProVision software command

HP Switch# display link-aggregation summary

Aggregation Interface Type:BAGG -- Bridge-Aggregation, RAGG -- Route-AggregationAggregation Mode: S -- Static, D -- DynamicLoadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Actor System ID: 0x43c0, 0017a4-ff43c0

AGG AGG Partner ID Select Unselect ShareInterface Mode Ports Ports Type-------------------------------------------------------------------------Dyn1 D 0x0, 0017a4-7eef40 n/a n/a n/a


2-131

Display Commandsdisplay link-aggregation summary

AGG Interface: Type and number of the aggregate interface.

Partner ID: System ID of the partner, which comprises the system LACP priority and the system MAC address. AGG Mode: Aggregation group type.

Select Ports: The number of Selected ports.

Unselect Ports: The number of Unselected ports.

Share Type: Load sharing type.



2-132

Display Commandsdisplay link-aggregation verbose

display link-aggregation verbose

Displays detailed information about the aggregation groups corresponding to the aggregate interfaces in the system.

To display the information of a specific Layer 2 aggregation group, use the display link-aggregation verbose bridge-aggregation bridge-aggregation-number command.

To display the information of all Layer 2 aggregate interfaces, use the display link-aggregation verbose bridge-aggregation command.


display link-aggregation verbosedisplay link-aggregation verbose Bridge-aggregationdisplay link-aggregation verbose Bridge-aggregation <aggregation-id>



2-133


Field Descriptions

Loadsharing Type: Loadsharing type:

• Shar for load sharing.

• NonS for non-load sharing.

Port Status: Port state: Selected or unselected.

Flags: One-octet LACP state flags field:

• A indicates whether LACP is enabled. 1 for enabled and 0 for disabled.

• B indicates the timeout control value. 1 for short timeout, and 0 for long timeout.

• C indicates whether the link is considered as aggregatable by the sending system. 1 for true, and 0 for false.

• D indicates whether the link is considered as synchronized by the sending system. 1 for true, and 0 for false.

• E indicates whether the sending system considers that collection of incoming frames is enabled on the link. 1 for true and 0 for false.

HP Switch# display link-aggregation verbose bridge-aggregation

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-LoadsharingPort Status: S -- Selected, U -- UnselectedFlags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation, D -- Synchronization, E -- Collecting, F -- Distributing, G -- Defaulted, H -- Expired

Aggregation Interface: Trk1Aggregation Mode: StaticLoadsharing Type: Shar Port Status Oper-Key--------------------------------------------------------------------------- A1 n/a 1

Aggregation Interface: Dyn1Aggregation Mode: DynamicLoadsharing Type: SharSystem ID: noneLocal: Port Status Priority Oper-Key Flag---------------------------------------------------------------------------- A2 n/a 32768 2 n/aRemote: Actor Partner Priority Oper-Key SystemID Flag---------------------------------------------------------------------------- A2 0 32768 0 n/a n/a


2-134


• F indicates whether the sending system considers that distribution of outgoing frames is enabled on the link. 1 for true and 0 for false.

• G indicates whether the receive state machine of the sending system is using default operational partner information. 1 for true and 0 for false.

• H indicates whether the receive state machine of the sending system is in the expired state. 1 for true and 0 for false.

If a flag bit is set to 1, the corresponding English letter that otherwise is not output is displayed.

Aggregation Interface: Name of the aggregate interface.

Aggregation Mode: Type of the aggregation group:

• Static for static aggregation.

• Dynamic for dynamic aggregation.

Port: Port type and number.

Status: State of the port.

Oper-Key: Operational key value.



2-135

Display Commandsdisplay lldp local-information

display lldp local-information

Displays the LLDP information. This includes the global information and per interface information.

HP Switch# display lldp local-informationGlobal LLDP local-information Chassis ID : 0000-0000-1122 System name : HP-E3500yl-48G System description : HP J8693A Switch E3500yl-48G, revision K.15.09.0000x, ROMK.15.28 HP-3500yl-48GCopyright (C) 1991-2012 Hewlett-Packard Development Company, L.P. System capabilities supported : Bridge, Router System capabilities enabled : Bridge

MED information device class : network Connectivity //This is intentional (MED inventory information of master board)

HardwareRev : Rev 0 FirmwareRev : K.15.28 SoftwareRev : K.15.09.0000x SerialNum : SG729TH003 Manufacturer name : Hewlett-Packard Model name : J8693A Asset tracking identifier : Unknown

LLDP local-information of port 1 : Port ID subtype : local Port ID : 1 Port description : 1

Management address type : ipv4 Management address : 1.2.3.4 Management address interface type : ipv6 Management address interface ID : 578 Management address OID : 0

Port VLAN ID(PVID) : 1


display lldp local-information No equivalent ProVision software command


2-136


Port and protocol VLAN ID(PPVID) : n/a port and protocol VLAN supported : n/a Port and protocol VLAN enabled : n/a

VLAN name of VLAN 1 : n/a

Auto-negotiation supported : Yes Auto-negotiation enabled : Yes OperMau : 30

PoE supported : n/a

Link aggregation supported : n/a Link aggregation enabled : n/a Aggregation port ID : n/a

Maximum frame Size : n/a

Media policy type : voice Signaling Unknown Policy : No VLAN tagged : No Media policy VlanID : 1 Media policy L2 priority : 6 Media policy Dscp : 46

LLDP local-information of port 2 : Port ID subtype : local Port ID : 2 Port description : 2

Management address type : ipv4 Management address : 10.0.0.5 Management address interface type : ipv6 Management address interface ID : 578 Management address OID : zeroDotZero


Port and protocol VLAN ID(PPVID) : n/a port and protocol VLAN supported : n/a Port and protocol VLAN enabled : n/a

VLAN name of VLAN <number> : n/a

Auto-negotiation supported : Yes Auto-negotiation enabled : Yes


2-137


OperMau : 30

PoE supported : n/a



Media policy type : voice Signaling Unknown Policy : No VLAN tagged : No Media policy VlanID : 1 Media policy L2 priority : 6 Media policy Dscp : 46



2-138

Display Commandsdisplay lldp local-information global

display lldp local-information global

Displays LLDP system global information.

HP Switch# display lldp local-information global

Global LLDP local-information Chassis ID : 0000-0000-1122/00 System name : HP-E3500yl-48G System description : HP J8693A Switch E3500yl-48G, revision K.15.09.0000x, ROMK.15.28HP-3500yl-48GCopyright (C) 1991-2012 Hewlett-Packard Development Company, L.P. System capabilities supported : Bridge, Router System capabilities enabled : Bridge

MED information device class : network Connectivity (MED inventory information of master board)

HardwareRev : Rev 0 FirmwareRev : K.15.28 SoftwareRev : K.15.09.0000x SerialNum : SG729TH003 Manufacturer name : Hewlett-Packard Model name : J8693A Asset tracking identifier : Unknown



display lldp local-information global No equivalent ProVision software command


2-139

Display Commandsdisplay lldp local-information interface interface-type interface-number

display lldp local-information interface interface-type interface-number

Displays LLDP detailed information for a given interface.

HP Switch# display lldp local-information interface 47LLDP local-information of port 47 : Port ID subtype : local Port ID : 47 Port description : 47

Management address type : ipv4 Management address : 1.2.3.4 Management address interface type : ipv6 Management address interface ID : 578 Management address OID : 0


Port and protocol VLAN ID(PPVID) : n/a Port and protocol VLAN supported : n/a Port and protocol VLAN enabled : n/a

VLAN name of VLAN 1: n/a

Auto-negotiation supported : Yes Auto-negotiation enabled : Yes OperMau : 30

Power port class : n/a PSE power supported : n/a PSE power enabled : n/a PSE pairs control ability : n/a Power pairs : n/a Port power classification : n/a



display lldp local-information interface interface-type interface-number



2-140

Display Commandsdisplay lldp local-information interface interface-type interface-number


MED information Media policy type : voice Signaling Unknown Policy : No VLAN tagged : No Media policy VlanID : 1 Media policy L2 priority : 6 Media policy Dscp : 46

PoE PSE power source : n/a Port PSE Priority : n/a Port available power value : n/a



2-141

Display Commandsdisplay lldp neighbor-information brief

display lldp neighbor-information brief

Displays brief information of all the ports connected to neighbors.

HP Switch# display lldp neighbor-information brief LLDP neighbor-information of port 1 : Neighbor 1: ChassisID/subtype: 0023-4751-ba80/MAC address PortID/subtype : 34/Locally assigned Capabilities : Bridge,Router

LLDP neighbor-information of port 2 :Neighbor 1:

ChassisID/subtype: 0021-f71b-fc40/MAC address PortID/subtype : 1/Locally assigned Capabilities : Bridge,Router


HP Switch# show lldp info remote-device A3LLDP Remote Device Information DetailLocal Port : A3ChassisType : mac-addressChassisId : 00 16 35 ff 2d 40PortType : localPortId : 23SysName : HPSwitchSystem Descr : HP Switch 3500-24, revision K.14.xxPortDescr : 23Pvid : 55System Capabilities Supported : bridge, routerSystem Capabilities Enabled : bridgeRemote Management AddressType : ipv4Address : 10.0.102.198Poe Plus Information DetailPoe Device Type : Type2 PDPower Source : Only PSEPower Priority : lowPD Requested Power Value : 20 Watts


display lldp neighbor-information brief show lldp info remote-device


2-142

Display Commandsdisplay lldp neighbor-information brief

PSE Actual Power Value : 20 Watts




2-143

Display Commandsdisplay lldp neighbor-information list display lldp neighbor-information list system-name <string>

display lldp neighbor-information list display lldp neighbor-information list system-name <string>

HP Switch# display lldp neighbor_information listSystem Name Local Interface Chassis ID Port IDHP Switch 1 00 0f 90 dc 9f 80 1


HP Switch# show lldp info remote-device A3LLDP Remote Device Information DetailLocal Port : A3ChassisType : mac-addressChassisId : 00 16 35 ff 2d 40PortType : localPortId : 23SysName : HPSwitchSystem Descr : HP Switch 3500-24, revision K.14.xxPortDescr : 23Pvid : 55System Capabilities Supported : bridge, routerSystem Capabilities Enabled : bridgeRemote Management AddressType : ipv4Address : 10.0.102.198Poe Plus Information DetailPoe Device Type : Type2 PDPower Source : Only PSEPower Priority : lowPD Requested Power Value : 20 WattsPSE Actual Power Value : 20 Watts

Whereas Comware can accpet multiple strings as input with spaces for system name, ProVision accepts only one string.




display lldp neighbor-information listdisplay lldp neighbor-information list system-name <string>

show lldp info remote-device


2-144

Display Commandsdisplay lldp statistics

display lldp statistics

Displays information about LLDP packets that are being advertised by the local system or by remote systems, and global LLDP information followed by each interface in the switch. The statistics refer to significant events that involve LLDP packet transmission and reception.

HP Switch# display lldp statistics LLDP statistics global information:LLDP neighbor information last change time:33 days,19 hours,39 minutes,37 secondsThe number of LLDP neighbor information inserted : 10The number of LLDP neighbor information deleted : 10The number of LLDP neighbor information dropped : 0The number of LLDP neighbor information aged out : 8

LLDP statistics information of port 1 [GigabitEthernet1/0/1]:The number of LLDP frames transmitted : 1713The number of LLDP frames received : 1200The number of LLDP frames discarded : 0The number of LLDP error frames : 1200The number of LLDP TLVs discarded : 1200The number of LLDP TLVs unrecognized : 0The number of LLDP neighbor information aged out : 1The number of CDP frames transmitted : n/aThe number of CDP frames received : n/aThe number of CDP frames discarded : n/aThe number of CDP error frames : n/a

LLDP statistics information of port 2 [GigabitEthernet1/0/2]:The number of LLDP frames transmitted : 2783The number of LLDP frames received : 1211The number of LLDP frames discarded : 0


HP Switch# show lldp statsLLDP Device StatisticsNeighbor Entries List Last Updated : 2 hoursNew Neighbor Entries Count : 20Neighbor Entries Deleted Count : 20Neighbor Entries Dropped Count : 0


display lldp statistics show lldp stats


2-145

Display Commandsdisplay lldp statistics

Neighbor Entries AgeOut Count : 20LLDP Port StatisticsPort | NumFramesRecvd NumFramesSent NumFramesDiscarded------ + -------------- ------------- ------------------A1 | 97317 97843 0A2 | 21 12 0A3 | 0 0 0A4 | 446 252 0A5 | 0 0 0A6 | 0 0 0A7 | 0 0 0




2-146

Display Commandsdisplay lldp statistics global

display lldp statistics global

Displays global information about LLDP packets that are being advertised by the local system or by remote systems. The statistics refer to significant events that involve LLDP packet transmission and reception.

HP Switch# display lldp statistics globalLLDP statistics global information:LLDP neighbor information last change time:33 days,19 hours,39 minutes,37 secondsThe number of LLDP neighbor information inserted : 10The number of LLDP neighbor information deleted : 10The number of LLDP neighbor information dropped : 0The number of LLDP neighbor information aged out : 8


HP Switch# show lldp statsLLDP Device StatisticsNeighbor Entries List Last Updated : 2 hoursNew Neighbor Entries Count : 20Neighbor Entries Deleted Count : 20Neighbor Entries Dropped Count : 0Neighbor Entries AgeOut Count : 20LLDP Port StatisticsPort | NumFramesRecvd NumFramesSent NumFramesDiscarded------ + -------------- ------------- ------------------A1 | 97317 97843 0A2 | 21 12 0A3 | 0 0 0A4 | 446 252 0A5 | 0 0 0A6 | 0 0 0A7 | 0 0 0




display lldp statistics global show lldp stats


2-147

Display Commandsdisplay lldp statistics interface interface-type interface-number

display lldp statistics interface interface-type interface-number

Displays information about LLDP packets on a particular interface that are being advertised by the local system or by remote systems. The statistics refer to significant events that involve LLDP packet transmission and reception.

HP Switch# display lldp statistics interface 1LLDP statistics information of port 1 [GigabitEthernet1/0/1]:The number of LLDP frames transmitted : 1713The number of LLDP frames received : 1200The number of LLDP frames discarded : 0The number of LLDP error frames : 1200The number of LLDP TLVs discarded : 1200The number of LLDP TLVs unrecognized : 0The number of LLDP neighbor information aged out : 1The number of CDP frames transmitted : n/aThe number of CDP frames received : n/aThe number of CDP frames discarded : n/aThe number of CDP error frames : n/a


HP Switch# show lldp statsLLDP Device StatisticsNeighbor Entries List Last Updated : 2 hoursNew Neighbor Entries Count : 20Neighbor Entries Deleted Count : 20Neighbor Entries Dropped Count : 0Neighbor Entries AgeOut Count : 20LLDP Port StatisticsPort | NumFramesRecvd NumFramesSent NumFramesDiscarded------ + -------------- ------------- ------------------A1 | 97317 97843 0A2 | 21 12 0A3 | 0 0 0A4 | 446 252 0A5 | 0 0 0A6 | 0 0 0A7 | 0 0 0


display lldp statistics interface interface-type interface-number

show lldp stats


2-148

Display Commandsdisplay lldp statistics interface interface-type interface-number




2-149

Display Commandsdisplay lldp status

display lldp status

Displays information about Link Layer Discovery Protocol (LLDP) and Link Level Discovery Protocol-Media Endpoint Discovery (LLDP-MED) configura-tion and capabilities on the switch. LLDP and LLDP-MED are used to learn about and to distribute device information on network links. This command shows information on global level as well as the interface level.

HP Switch# display lldp statusThe current number of LLDP neighbors: 0The current number of CDP neighbors: 0LLDP neighbor information last changed time: 33 days,19 hours,39 minutes,37 secondsTransmit interval : 30sHold multiplier : 4Reinit delay : 2sTransmit delay : 2sTrap interval : 5sFast start times : 3

Port 1 [GigabitEthernet1/0/1]:Port status of LLDP : EnableAdmin status : Tx_RxTrap flag : NoPolling interval : 0s

Number of neighbors: : 0Number of MED neighbors : 0Number of CDP neighbors : 0Number of sent optional TLV : 0Number of received unknown TLV : 0



display lldp status No equivalent ProVision software command


2-150

Display Commandsdisplay lldp status interface interface-type interface number

display lldp status interface interface-type interface number

Displays information about Link Layer Discovery Protocol (LLDP) and Link Level Discovery Protocol-Media Endpoint Discovery (LLDP-MED) configura-tion and capabilities on the switch. LLDP and LLDP-MED are used to learn about and to distribute device information on network links.

HP Switch# display lldp status interface 1

Port 1 :Port status of LLDP : EnableAdmin status : Tx_RxTrap flag : NoPolling interval : 0s

Number of neighbors: 0Number of MED neighbors : 0Number of CDP neighbors : 0Number of sent optional TLV : 0Number of received unknown TLV : 0



display lldp status interface interface-type interface number



2-151

Display Commandsdisplay lldp tlv-config interface interface-type interface-number

display lldp tlv-config interface interface-type interface-number

LLDP information is sent by devices from each of their interfaces at a fixed interval in the form of an Ethernet frame. Each frame contains one Link Layer Discovery Protocol Data Unit (LLDPDU). Each LLDPDU is a sequence of type-length-value (TLV) structures. Each LLDP frame starts with the following mandatory TLVs: Chassis ID, Port ID, and Time-to-Live. The mandatory TLVs are followed by any number of optional TLVs. All Optional TLVs can be configured per port basis and can be displayed with the help of this command for a particular interface.

HP Switch# display lldp tlv-configLLDP tlv-config of port 98[GigabitEthernet2/0/2]:NAME STATUS DEFAULTBasic optional TLV:Port Description TLV YES YESSystem Name TLV YES YESSystem Description TLV YES YESSystem Capabilities TLV YES YESManagement Address TLV YES YES

IEEE 802.1 extend TLV:Port VLAN ID TLV YES YESPort And Protocol VLAN ID TLV YES YESVLAN Name TLV YES YES

IEEE 802.3 extend TLV:MAC-Physic TLV YES YESPower via MDI TLV YES YESLink Aggregation TLV YES YESMaximum Frame Size TLV YES YES

LLDP-MED extend TLV:Capabilities TLV YES YESNetwork Policy TLV YES YESLocation Identification TLV NO NOExtended Power via MDI TLV YES YESInventory TLV YES YES



display lldp tlv-config interface interface-type interface-number



2-152

Display Commandsdisplay logfile buffer

display logfile buffer

Displays system log information.

HP Switch# display logfile buffer

%@00061%Jan 01 00:00:47 2090 system: --------------------------

%@00062%Jan 01 00:00:47 2090 system: Mgmt Module 1 went down without saving crash information

%@03002%Jan 01 00:00:47 2090 system: System reboot due to Reset Switch

%@02759%Jan 01 00:00:47 2090 chassis: Savepower LED timer is OFF.

%@00433%Jan 01 00:00:47 2090 ssh: Ssh server enabled

%@00092%Jan 01 00:00:47 2090 dhcp: Enabling Auto Image Config Download via DHCP and turning off auto-tftp if enabled

%@00690%Jan 01 00:00:48 2090 udpf: DHCP relay agent feature enabled

%@02637%Jan 01 00:00:48 2090 srcip: TACACS admin policy is 'outgoing interface'

%@02638%Jan 01 00:00:48 2090 srcip: TACACS oper policy is 'outgoing interface'

%@02637%Jan 01 00:00:48 2090 srcip: RADIUS admin policy is 'outgoing interface'

%@02638%Jan 01 00:00:48 2090 srcip: RADIUS oper policy is 'outgoing interface'

%@02637%Jan 01 00:00:48 2090 srcip: SYSLOG admin policy is 'outgoing interface'

%@02638%Jan 01 00:00:48 2090 srcip: SYSLOG oper policy is 'outgoing interface'

%@02637%Jan 01 00:00:48 2090 srcip: TELNET admin policy is 'outgoing


display logfile buffer show logging


2-153



HP Switch# show loggingKeys: W=Warning I=Information M=Major D=Debug E=Error---- Event Log listing: Events Since Boot ----

I 10/28/09 21:45:42 00061 system: AM1: ------------------------

I 10/28/09 21:45:42 00062 system: AM1: Mgmt Module 1 went down without saving crash information

M 10/28/09 21:45:42 03002 system: AM1: System reboot due to Reset Switch

I 10/28/09 21:45:42 02759 chassis: AM1: Savepower LED timer is OFF.

I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot A configured ON.

I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot B configured ON.

I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot C configured ON.

I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot D configured ON.

I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot E configured ON.

I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot F configured ON.

I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot G configured ON.

I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot H configured ON.

I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot I configured ON.

I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot J configured ON.

I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot K configured ON.

I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot L configured ON.

I 10/28/09 21:45:42 00937 chassis: AM1: Fabric 1 inserted


2-154


I 10/28/09 21:45:42 00937 chassis: AM1: Fabric 2 inserted

I 10/28/09 21:45:43 00092 dhcp: AM1: Enabling Auto Image Config Download via DHCP and turning off auto-tftp if enabled

I 10/28/09 21:45:43 00690 udpf: AM1: DHCP relay agent feature enabled

I 10/28/09 21:45:43 02637 srcip: AM1: TACACS admin policy is 'outgoing interface'

I 10/28/09 21:45:43 02638 srcip: AM1: TACACS oper policy is 'outgoing interface'

Operating Notes





2-155

Display Commandsdisplay loopback-detection

display loopback-detection

Displays the operating status of the loopback detection function.

Field Descriptions

Detection Interval: Loopback detection interval in seconds.

Action Mode: The loopback detection action:

• None—When detecting a looped port, the system prints log informa-tion and sends trap messages.

• Shutdown—When detecting a looped port, the system prints log information, sends trap messages, and shuts down the port.

There is no related ProVision command.



display loopback-detection No equivalent ProVision software command

HP Switch(config)# display loopback-detection

Loopback-detection is running. Detection interval is 30 second(s). Action mode: None Loopback-detection is enabled on the following VLAN(s): 1, 20, 315, 1001, 2008, 2010-2015, 2026 Loopback is detected on the following interface(s): 1 2 3 10


2-156

Display Commandsdisplay mac-address

display mac-address

Displays information about the MAC address table.

HP Switch# display mac-address

MAC ADDR VLAN ID STATE PORT INDEX AGING TIME(s)001635-22ca40 1 Learned A1 AGING001635-22ca7f 1 Learned A1 AGING001122-334455 2 Config static A2 NOAGED

--- 3 mac address(es) found ---


HP Switch# show mac-address 000009-21ae04Status and Counters - Address Table - 080009-21ae84MAC Address : 080009-21ae84Locate on Port : A2

Operating Notes





display mac-address show mac-address


2-157

Display Commandsdisplay mac-address aging-time

display mac-address aging-time

Displays the aging time of dynamic entries in the MAC address table.

Field Descriptions

Mac address aging time: Aging time of dynamic entries in the MAC address table.

Operating Notes

Comware displays mac-address as 1234-1234-1234 and ProVision displays it as 123456-123456.

For more information about MAC aging time, see the “Interface Access and System Information” chapter in the latest Basic Operation Guide for your switch.



display mac-address aging-time show system information

HP Switch# display mac-address aging-timeMac address aging time: 300s

HP Switch# show system information

Status and Counters - General System Information

System Name : HP Switch System Contact : System Location :


Time Zone : 0 Daylight Time Rule : None


2-158

Display Commandsdisplay mac-address aging-time

display mac-address aging-time Field Mappings.



Mac address aging time MAC Age Time (sec)


2-159

Display Commandsdisplay mac-address multicast

display mac-address multicast

Displays static multicast MAC address entries.

HP Switch# display mac-address multicastMAC ADDR VLAN ID STATE PORT INDEX AGING TIME(s)010122-334455 1 Multicast A1 NOAGED012222-334455 1 Multicast F24 NOAGED

--- 2 mac address(es) found ---



display mac-address multicast No equivalent ProVision software command


2-160

Display Commandsdisplay mac-authentication

display mac-authentication

Displays MAC authentication settings and statistics, including the global settings, and port-specific settings and MAC authentication and online user statistics.

If you specify a list of ports, the command displays port-specific settings and statistics only for the specified ports.

If you do not specify any port, the command displays port-specific settings and statistics for all ports.


display mac-authentication [interface] show port-access mac-based


2-161


Field Descriptions

MAC address authentication is enabled: Whether MAC authentication is enabled.

User name format is no-delimiter like no delimiter format: Type of user account, which can be MAC-based or shared. If MAC-based accounts are used, this field displays “User name format is MAC address …” and the format settings for usernames and passwords. For example, MAC addresses without hyphens in lower case. If a shared account is used, this field displays “User name format is fixed account.”

Fixed username: Username of the shared account for MAC authentication users. If MAC-based accounts are used, this field displays mac.

Fixed password: Password of the shared account for MAC authentication users. If MAC-based accounts are used, this field displays not configured.

Offline detect period: Setting of the offline detect timer.

Quiet period: Setting of the quiet timer.

HP Switch(config)# display mac-authentication

MAC address authentication is n/a User name format is no-delimiter like aabbccddeeff Fixed Username:n/a Fixed password:not configured Offline detect period is 0s Quiet period is 0s Server response timeout value is 0s The max allowed user number is n/a per slot Current user number amounts to 0 Current domain: n/a

Silent MAC User info: MAC Addr From Port Port Index n/a n/a n/a

A1 is link-up MAC address authentication is disabled Authenticate success: n/a, failed: n/a Max number of on-line users is 1 Current online user number is 0 MAC Addr Authenticate state AuthIndexA2 is link-down MAC address authentication is disabled Authenticate success: n/a, failed: n/a Max number of on-line users is 1 Current online user number is 0 MAC Addr Authenticate state AuthIndex


2-162


Server response timeout value: Setting of the server timeout timer.

The max allowed user number: Maximum number of users each slot supports.

Current user number amounts to: Number of online users.

Current domain: not configured, use default domain: Authentication domain that is currently used.

Silent Mac User info: Information about silent MAC addresses. A MAC address is marked silent when it fails a MAC authentication, and at the same time, a quiet timer starts. Before the timer expires, the device drops any packet from the MAC address and does not perform MAC authentication for the MAC address.

GigabitEthernet3/0/1 is link-up: Status of the link on port GigabitEthernet 3/0/1. In this example, the link is up.

MAC address authentication is enabled: Whether MAC authentication is enabled on port GigabitEthernet 3/0/1.

Authenticate success: 0, failed: 0: MAC authentication statistics, including the number of successful and unsuccessful authentication attempts.

Current online user number: Number of online users on the port.

MAC Addr: MAC address of the online user.

Authenticate state: User status. Possible values include the following:

• CONNECTING—The user is logging in.

• SUCCESS—The user has passed the authentication.

• FAILURE—The user failed the authentication.

• LOGOFF—The user has logged off.

AuthIndex: Authenticator index.

Operating Notes

For more information on switch MAC authentication operation, see the “Web and MAC Authentication” chapter in the latest Access Security Guide for your switch.


2-163



display mac-authentication [interface] Field Mappings.

HP Switch(config)# show port-access mac-based

Port Access MAC-Based Status

Auth Unauth Untagged Tagged Port % In RADIUS Port Clients Clients VLAN VLANs COS Limit ACL ---- ------- ------- -------- ------ -------- ------ ------ 1 1 1 2003 Yes 70000000 100 Yes 2 2 0 MACbased No Yes Yes Yes 3 4 0 1 Yes No No No


MAC address authentication is enabled n/a

User name format is MAC address in lowercase, like xxxxxxxxxxxx

n/a

Fixed username n/a

Fixed password n/a

Offline detect period n/a

Quiet period n/a

Server response timeout value n/a

the max allowed user number n/a

Current user number amounts to n/a

Current domain: not configured, use default domain

n/a

Silent Mac User info n/a

GigabitEthernet3/0/1 is link-up n/a

MAC address authentication is enabled n/a

Authenticate success: 0, failed: 0 n/a

Current online user number n/a

MAC Addr n/a


2-164



Authenticate state n/a

AuthIndex n/a



2-165

Display Commandsdisplay mac-authentication [interface …]

display mac-authentication [interface …]

Displays MAC authentication settings and statistics.

HP Switch# display mac-authentication interface configurationMAC address authentication is n/a User name format is no-delimiter like aabbccddeeff Fixed Username:n/a Fixed password:not configured Offline detect period is 0s Quiet period is 0s Server response timeout value is 0s The max allowed user number is n/a per slot Current user number amounts to 0 Current domain: n/aSilent MAC User info: MAC Addr From Port Port Index n/a n/a n/aA1 is link-up MAC address authentication is disabled Authenticate success: n/a, failed: n/a Max number of on-line users is 1 Current online user number is 0 MAC Addr Authenticate state AuthIndexA2 is link-down MAC address authentication is disabled Authenticate success: n/a, failed: n/a Max number of on-line users is 1 Current online user number is 0 MAC Addr Authenticate state AuthIndex


HP Switch# show port-access mac-based config

Port Access MAC-Based Configuration

MAC Address Format : no-delimiterPassword : secretMAC1

Unauth Redirect Configuration URL :

Unauth Redirect Client Timeout (sec) : 1800


display mac-authentication [interface ...] show port-access mac-based


2-166

Display Commandsdisplay mac-authentication [interface …]

Unauth Redirect Restrictive Filter : DisabledTotal Unauth Redirect Client Count : 0

Client Client Logoff Re-Auth Unauth Auth CntrlPort Enabled Limit Moves Period Period VLAN ID VLAN ID Dir

---- ------- ------ ------ ------- ------- ------- -------- -----1 No 1 No 300 0 0 0 both2 No 1 No 300 0 0 0 both3 No 1 No 300 0 0 0 both4 No 1 No 300 0 0 0 both5 No 1 No 300 0 0 0 both6 No 1 No 300 0 0 0 both7 No 1 No 300 0 0 0 both8 No 1 No 300 0 0 0 both

Operating Notes




2-167

Display Commandsdisplay memory

display memory

Displays the current memory usage on the switch.

HP Switch(config)# display memory System Total Memory(bytes): 128090112 Total Used Memory(bytes): 47385504 Used Rate: 36%

Field Descriptions

System Total Memory (bytes): Total system memory in the switch.

Total Used Memory (bytes): Total system memory in use.

Used Rate: Percentage of system memory in use.

Operating Notes

To display memory usage in ProVision Software, use the following command:


This command lists the total memory and free memory available in the switch, along with other system-related information.

For more on system information, refer to the “Interface Access and System Information” chapter in the latest Basic Operation Guide for your switch.


display memory show system information


2-168

Display Commandsdisplay memory




Status and Counters - General System Information

System Name : HP Switch System Contact : System Location :


Time Zone : -480 Daylight Time Rule : Continental-US-and-Canada

Software revision : K.15.08.0003 Base MAC Addr : 001871-c42f00 ROM Version : K.15.27 Serial Number : SG641SU00L Allow V1 Modules : Yes Opacity Shields : Not Installed

Up Time : 3 hours Memory - Total : 128,040,960 CPU Util (%) : 0 Free : 80,694,816

IP Mgmt - Pkts Rx : 126,890 Packet - Total : 6750 Pkts Tx : 5123 Buffers Free : 5086 Lowest : 5051 Missed : 0


2-169

Display Commandsdisplay mld group

display mld group

Displays the number of active MLD (Multicast Listener Discovery) groups and the VLAN and IPv6 address on which each group is active.HP Switch# display mld group Total 4 MLD Group(s).Interface group report information Vlan-Interface1(1234:1::5): Total 1 MLD Groups reported Group Address : ff1e::1 Last Reporter : fe80::200:f7ff:fe95:4f5d Uptime : 00:45:00 Expires : 00:03:20 Vlan-Interface2(1234:3::5): Total 2 MLD Groups reported Group Address : ff1e::3 Last Reporter : fe80::200:f7ff:fe95:da95 Uptime : 00:43:28 Expires : 00:03:16 Group Address : ff1e::4 Last Reporter : fe80::200:f7ff:fe95:da95 Uptime : 00:43:28 Expires : 00:03:16 Vlan-Interface10(1234:2::5): Total 1 MLD Groups reported Group Address : ff1e::5 Last Reporter : fe80::200:f7ff:fe95:9c92 Uptime : 00:43:41 Expires : 00:03:20


display mld group show ipv6 mld


2-170


Field Descriptions

Total n MLD Groups: The total number of MLD groups detected on the switch.

VLAN-interface< id > ( < ipv6-addr > ): A specific VLAN interface

Total n MLD Groups reported: The number of MLD groups detected on the indicated VLAN.

Group Address: The IPv6 address of an MLD group detected on the indicated VLAN.

• Last Reporter: The IPv6 address of the host that last reported member-ship for the group.

• Uptime: Length of time since the IPv6 multicast group was joined.

• Expires: Time remaining for the IPv6 multicast group.

Operating Notes

The display mld group command reports on MLD traffic on static VLANs.

The switch supports MLDv1 and MLDv2.

To enable MLD operation in ProVision software, use the following command in a VLAN configuration context:

ipv6 mld < enable | disable >

For example:

HP Switch(vlan-10)# ipv6 mld enable

For more on MLD, including additional MLD commands, see the “Multicast Listener Discovery (MLDv1 and MLDv2)” chapter in the latest IPv6 Configu-

ration Guide for your switch.


2-171



HP Switch(config)# show ipv6 mld

MLD Service Protocol Info

Total vlans with MLD enabled : 2 Current count of multicast groups joined : 2

VLAN ID : 1 NAME : DEFAULT_VLAN MLD Version : 2

MLD Interface State : Querier Querier Address : fe80::218:71ff:fec4:2f00 [this switch] Version : 2 Uptime : 11m 55s Expires : 1m 5s Ports with multicast routers :

Active Group Addresses Tracking Vers Mode Uptime Expires ---------------------------------------- -------- ---- ---- -------- -------- ff3e:30:2001:db8:8:0:7:101 Filtered 2 EXC 20h 55m 22h 50m VLAN ID : 2 NAME : VLAN2 MLD Version : 2

MLD Interface State : Non-Querier Querier Address : :: Version : - Uptime : - Expires : - Ports with multicast routers :

Active Group Addresses Tracking Vers Mode Uptime Expires ---------------------------------------- -------- ---- ---- -------- -------- ff33:30:2001:db8:8:0:7:102 Filtered 2 INC 10m 40s 12m 17s


2-172


mld group Field Mappings.


Comware ProVision

n/a Total vlans with MLD enabled

Total n mld Group(s) Current count of multicast groups joined

Vlan Interfacen(ipv6-addr) VLAN ID Active Group Addresses

Total n MLD Groups reported n/a

n/a NAME

n/a MLD Version

n/a MLD Interface State

n/a Tracking Vers Mode Uptime Expires


2-173

Display Commandsdisplay mld group interface vlan-interface <vid>

display mld group interface vlan-interface <vid>

Displays information of all MLD groups.

HP Switch# display mld group interface vlan-interface 30Interface group report informationVlan-Interface30(2075:1:1:30::1): Total 5 MLD Groups reported Group : ff02::2 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:18 Group : ff02::16 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:26 Group : ff02::1:ff00:0 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:26 Group : ff02::1:ff00:3 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:17 Group : ff02::1:ffab:9300 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:24

Field Descriptions:Group: Multicast group address





There is no direct equivalent ProVision command. Please see “show ipv6 mld vlan <vid>” on page 2-179.



display mld group interface vlan-interface <vid> show ipv6 mld vlan <vid>


2-174

Display Commandsdisplay mld group interface vlan-interface <vid> verbose

display mld group interface vlan-interface <vid> verbose


HP Switch# display mld group interface vlan-interface 30 verbose Interface group report informationVlan-Interface30(2075:1:1:30::1): Total 5 MLD Groups reported Group : ff02::2 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:04:00 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::16 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:54 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::1:ff00:0 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:53 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::1:ff00:3 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:58 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a


display mld group interface vlan-interface <vid> verbose

show ipv6 mld vlan <vid>


2-175

Display Commandsdisplay mld group interface vlan-interface <vid> verbose

Last-listener-query-timer-expiry : n/a Group : ff02::1:ffab:9300 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:56 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a

Field Descriptions:

Interface group report information: MLD group information on the interface

Total 5 MLD Groups reported: Five MLD groups were reported.

Group: IPv6 multicast group address

Uptime: Length of time since the IPV6 multicast group was joined

Expires: Remaining time of the IPv6 multicast group, where “off” means that the multicast group never times out

Last reporter: IPv6 address of the host that last reported membership for this group

Last-listener-query-counter: Number of MLD last listener queries sent

Last-listener-query-timer-expiry: Remaining time of the MLD last listener query timer, where “off” means that the timer never times out

Group mode: Multicast source filtering mode:

• include

• exclude

This field is displayed only when the device is running MLDv2.

Version1-host-present-timer-expiry: Remaining time of the MLDv1 host present timer, where “off” means that the timer never times out.






2-176

Display Commandsdisplay mld group port-info vlan <vlan-id> display mld group port-info

display mld group port-info vlan <vlan-id> display mld group port-info

Displays Layer 2 port information of MLD groups, including Layer 2 informa-tion of dynamic and static MLD group entries.

HP Switch# display mld group port-info Total 1 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s). Port flags: D-Dynamic port, S-Static port, C-Copy port Subvlan flags: R-Real VLAN, C-Copy VLAN Vlan(id):100. Total 3 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s). Router port(s):total 0 port(s). IP group(s):the following ip group(s) match to one mac group. IP group address:FF13::1 (::, FF13::1): Host port(s):total 1 port(s). GE2/0/1 (D) MAC group(s): n/a

HP Switch# display mld group port-info vlan 100 Total 1 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s). Port flags: D-Dynamic port, S-Static port, C-Copy port Subvlan flags: R-Real VLAN, C-Copy VLAN Vlan(id):100. Total 3 IP Group(s). Total n/a IP Source(s). Total n/a MAC Group(s). Router port(s):total 0 port(s). IP group(s):the following ip group(s) match to one mac group. IP group address:FF13::1 (::, FF13::1): Host port(s):total 1 port(s). A1 (D) MAC group(s): n/a



display mld group port-info vlan <vlan-id>display mld group port-info



2-177

Display Commandsdisplay mld group verbose

display mld group verbose

Displays information about dynamically added MLD groups on all interfaces.

HP Switch# display mld group verboseTotal 5 MLD Group(s).Interface group report informationVlan-Interface30(2075:1:1:30::1): Total 5 MLD Groups reported Group : ff02::2 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:31 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::16 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:26 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::1:ff00:0 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:24 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::1:ff00:3 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:30 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a Group : ff02::1:ffab:9300


display mld group verbose show ipv6 mld vlan <vid>


2-178

Display Commandsdisplay mld group verbose

Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:03:28 Group mode : exclude Version1-host-present-timer-expiry : on Last-listener-query-counter : n/a Last-listener-query-timer-expiry : n/a

Field Descriptions:


Total 1 MLD Groups reported: One MLD group was reported.








• include

• exclude








2-179

Display Commandsdisplay mld group x:x::x:x

display mld group x:x::x:x


HP Switch# display mld group ff02::2Interface group report information Interface:Vlan30 Last Reporter : fe80::3e4a:92ff:feab:9300 Uptime : 5 ... Expires : 00:02:38

Field Descriptions:






There is no equivalent ProVision command.

HP Switch# show ipv6 mld vlan 30

MLD Service Protocol Info

VLAN ID : 30 NAME : VLAN30 MLD Version : 2

MLD Interface State : Non-Querier Querier Address : fe80::3e4a:92ff:feab:9300 Port : A2 Version : 2 Uptime : 5d 18h 38m Expires : 3m 48s Ports with multicast routers : A2


display mld group x:x::x:x show ipv6 mld vlan <vid>


2-180

Display Commandsdisplay mld group x:x::x:x

Active Group Addresses Tracking Vers Mode Uptime Expires ----------------------- ------- ---- ---- -------- -----

ff02::2 Standard 1 EXC 5d 18... 2m 30s ff02::16 Standard 1 EXC 5d 18... 2m 33s ff02::1:ff00:0 Standard 1 EXC 5d 18... 2m 28s ff02::1:ff00:3 Standard 1 EXC 5d 18... 2m 27s ff02::1:ffab:9300 Standard 1 EXC 5d 18... 2m 24s



2-181

Display Commandsdisplay mld group x:x::x:x verbose

display mld group x:x::x:x verbose


HP Switch# display mld group verbose

Interface group report informationVlan-interface100(FE80::101) Total 1 MLD Groups reported Group: FF03::101 Uptime: 00:01:46 Expires: 00:01:30 Last reporter: FE80::10 Last-listener-query-counter: 0 Last-listener-query-timer-expiry: off Group mode: include Version1-host-present-timer-expiry: off

Field Descriptions:


Total 1 MLD Groups reported: One MLD group was reported.








• include

• exclude


display mld group x:x::x:x verbose show ipv6 mld vlan <vid>


2-182

Display Commandsdisplay mld group x:x::x:x verbose








2-183

Display Commandsdisplay mld interface

display mld interface

Displays MLD configuration and operation information on the specified inter-face or all MLD-enabled interfaces.

HP Switch# display mld interfaceInterface informationVlan-Interface30(2075:1:1:30::1):MLD is enabledCurrent MLD version is 2Value of query interval for MLD(in seconds) : 125 Value of other querier present interval for MLD(in seconds) : 255 Value of maximum query response time for MLD(in seconds) : 10 Querier for MLD : fe80::3e4a:92ff:feab:9300 Total 5 MLD Groups reported

Field Descriptions:

Vlan-interface30 (2075:1:1:30::1): Interface and IPv6 link-local address

Current MLD version: MLD version running on the interface

Value of query interval for MLD (in seconds): MLD query interval, in seconds

Value of other querier present interval for MLD (in seconds): MLD other querier present interval, in seconds

Value of maximum query response time for MLD (in seconds): Maximum response delay for general query messages (in seconds)

Querier for MLD: IPv6 link-local address of the MLD querier

Total 5 MLD Groups reported: Total number of MLD groups the interface has dynamically joined





display mld interface show ipv6 mld vlan <vid>


2-184

Display Commandsdisplay mld interface verbose

display mld interface verbose


HP Switch# display mld interface verboseInterface informationVlan-Interface30(2075:1:1:30::1): MLD is enabled Current MLD version is 2 Value of query interval for MLD(in seconds) : 125 Value of other querier present interval for MLD(in seconds) : 255 Value of maximum query response time for MLD(in seconds) : 10 Querier for MLD : fe80::3e4a:92ff:feab:9300 Value of last listener query interval(in seconds) : 1 Value of startup query interval(in seconds) : 31 Value of startup query count : 2 General query timer expiry (hours:minutes:seconds) : 00:03:19 MLD activity : 19861 joins, 0 leaves Multicast ipv6 routing on this interface : n/a Robustness : 2 Require-router-alert : enabled Fast-leave : enabled Ssm-mapping : n/a Startup-query-timer-expiry : off Other-querier-present-timer-expiry : on Proxying interface : n/a

Field Descriptions:

Vlan-Interface30(2075:1:1:30::1): Interface and IPv6 link-local address






display mld interface verbose show ipv6 mld vlan <vid>


2-185

Display Commandsdisplay mld interface verbose

Value of last listener query interval (in seconds): MLD last listener query interval, in seconds

Value of startup query interval(in seconds): MLD startup query interval, in sec-onds

Value of startup query count: Number of MLD general queries sent on startup

General query timer expiry: Remaining time of the MLD general query timer, where “off” means that the timer never times out


MLD activity: MLD activity statistics (number of join and done messages)

Robustness: MLD querier’s robustness variable

Require-router-alert: Dropping MLD messages without Router-Alert (enabled/disabled)

Fast-leave: MLD fast leave processing status (enabled/disabled)

Ssm-mapping: MLD SSM mapping status (enabled/disabled)

Startup-query-timer-expiry: Remaining time of MLD startup query timer, where “off” means that the timer never times out

Other-querier-present-timer-expiry: Remaining time of MLD other querier pres-ent timer, where “off” means that the timer never times out

Proxying interface: The MLD proxy interface, where “none” means that no proxy interface exists

MLD proxy is enabled: MLD proxying is enabled

Version1-querier-present-timer-expiry: Remaining time of the MLDv1 querier present timer, where “off” means that the timer never times out





2-186

Display Commandsdisplay mld interface vlan-interface <vid>

display mld interface vlan-interface <vid>


HP Switch# display mld interface vlan-interface 30 Vlan-Interface30(2075:1:1:30::1): MLD is enabled Current MLD version is 2 Value of query interval for MLD(in seconds) : 125 Value of other querier present interval for MLD(in seconds) : 255 Value of maximum query response time for MLD(in seconds) : 10 Querier for MLD : fe80::3e4a:92ff:feab:9300 Total 5 MLD Groups reported

Field Descriptions:

Vlan-Interface30(2075:1:1:30::1): Interface and IPv6 link-local address






Total 5 MLD Groups reported: Total number of MLD groups the interface has dynamically joined





display mld interface vlan-interface <vlan-id> show ipv6 mld vlan <vid>


2-187

Display Commandsdisplay mld interface vlan-interface <vid> verbose

display mld interface vlan-interface <vid> verbose


HP Switch# display mld interface vlan-interface 30 verboseVlan-Interface30(2075:1:1:30::1): MLD is enabled Current MLD version is 2 Value of query interval for MLD(in seconds) : 125 Value of other querier present interval for MLD(in seconds) : 255 Value of maximum query response time for MLD(in seconds) : 10 Querier for MLD : fe80::3e4a:92ff:feab:9300 Value of last listener query interval(in seconds) : 1 Value of startup query interval(in seconds) : 31 Value of startup query count : 2 General query timer expiry (hours:minutes:seconds) : 00:02:38 MLD activity : 19866 joins, 0 leaves Multicast ipv6 routing on this interface : n/a Robustness : 2 Require-router-alert : enabled Fast-leave : enabled Ssm-mapping : n/a Startup-query-timer-expiry : off Other-querier-present-timer-expiry : on Proxying interface : n/a Total 5 MLD Groups reported

Field Descriptions:

Vlan-interface100(FE80::200:AFF:FE01:101): Interface and IPv6 link-local address





display mld interface vlan-interface <vid> verbose

show ipv6 mld vlan <vid>


2-188

Display Commandsdisplay mld interface vlan-interface <vid> verbose


Value of last listener query interval (in seconds): MLD last listener query interval, in seconds

Value of startup query interval(in seconds): MLD startup query interval, in sec-onds

Value of startup query count: Number of MLD general queries sent on startup

General query timer expiry: Remaining time of the MLD general query timer, where “off” means that the timer never times out


MLD activity: MLD activity statistics (number of join and done messages)

Robustness: MLD querier’s robustness variable

Require-router-alert: Dropping MLD messages without Router-Alert (enabled/disabled)

Fast-leave: MLD fast leave processing status (enabled/disabled)

Ssm-mapping: MLD SSM mapping status (enabled/disabled)

Startup-query-timer-expiry: Remaining time of MLD startup query timer, where “off” means that the timer never times out

Other-querier-present-timer-expiry: Remaining time of MLD other querier pres-ent timer, where “off” means that the timer never times out

Proxying interface: The MLD proxy interface, where “none” means that no proxy interface exists

Total 1 MLD Group reported: Total number of MLD groups the interface has dynamically joined

MLD proxy is enabled: MLD proxying is enabled

Version1-querier-present-timer-expiry: Remaining time of the MLDv1 querier present timer, where “off” means that the timer never times out





2-189

Display Commandsdisplay mld routing-table

display mld routing-table

Displays information about the MLD routing table.

HP Switch# display mld routing-table Routing table Total 2 entries 00001. (*, 2ffd::1) List of 2 downstream interfaces Vlan-interface100 (fe80::3ee5:a6ff:fe18:1142), Protocol: MLD Vlan-interface200 (fe80::3ee5:a6ff:fe18:1143), Protocol: MLD 00002. (2ffc::9, 2ffd::1) List of 2 downstream interfaces in exclude mode Vlan-interface100 (fe80::3ee5:a6ff:fe18:1142), Protocol: MLD Vlan-interface200 (fe80::3ee5:a6ff:fe18:1143), Protocol: MLD



display mld routing-table No equivalent ProVision software command


2-190

Display Commandsdisplay monitor-link group [group-number | all],

display monitor-link group [group-number | all],

Displays information about the specified or all monitor link groups.

Field Descriptions

Monitor link group 1 information: Information about monitor link group 1.

Group status: Monitor link group state, which can be up or down or none.

Last-up-time: Last time when the monitor link group was up.

Last-down-time: Last time when the monitor link group was down.

Member: Member ports of the monitor link group.

Role: Port role, which can be uplink port or downlink port.

Status: Member link state, which can be up or down.

Operating Notes

In ProVision, groupid ranges from 1 to 64 whereas in H3C switches, groupid ranges from 1 to 24. For more information about link groups, see the “Port Status and Configuration” chapter in the latest Management and Configura-

tion Guide for your switch.


display monitor-link group<group-number | all]

show uplink-failure-detection

HP Switch# display monitor-link group 2 Monitor link group 2 information: Group status : NONE Last-up-time : n/a Last-down-time : n/a Member Role Status ------------------------------------------- 3 UPLINK DOWN 4 DOWNLINK DOWN


2-191

Display Commandsdisplay monitor-link group [group-number | all],


display monitor-link group Field Mappings.


HP Switch(config)# show uplink-failure-detection

Uplink Failure Detection Information UFD Enabled : Yes

TRACK ID | Monitored Links Links to Disable LtM State LtD State -------- + --------------- ---------------- --------- --------------- 3 5,6 3 Up Up 4 13 4-5 Down Auto-Disabled


Monitor link group Track ID

Group status UFD State

Last-up-time n/a

Last-down-time n/a

Member Monitored Links/Links to Disable

Role n/a

Status LtMState/LtD State


2-192

Display Commandsdisplay multicast forwarding-table

display multicast forwarding-table

Displays multicast forwarding table information. If neither all-instance nor vpn-instance is specified, this command displays the information on the public network. Multicast forwarding tables guide multicast forwarding. You can view the forwarding state of multicast traffic by checking the multicast forwarding table.

HP Switch# display multicast forwarding-table

Multicast Forwarding Table of VPN-Instance: n/a

Total 1 entry

Total 1 entry matched

00001. (30.30.30.1, 239.1.1.1) MID: n/a, Flags: 0x2:0 Uptime: 00:00:21, Timeout in: 00:00:02 Incoming interface: Vlan-interface10 List of 1 outgoing interfaces: 1: Vlan-interface20 Matched 2 packets(bytes n/a), Wrong If 0 packets Forwarded 0 packets(0 bytes)



display multicast forwarding-table No equivalent ProVision software command


2-193

Display Commandsdisplay multicast routing-table

display multicast routing-table

Displays multicast routing table information. Multicast routing tables are the basis of multicast forwarding. You can view the establishment state of an (S, G) entry by checking the multicast routing table.

HP Switch# display multicast routing-tableMulticast routing table of VPN-Instance: public netTotal 1 entry,1 matched

00001. (20.20.20.2, 239.1.1.1) Uptime: 00:00:20 Upstream Interface: 10 List of 1 downstream interfaces 1: Vlan-interface30

HP Switch# display multicast routing-table 20.20.20.1 239.1.1.1Multicast routing table of VPN-Instance: public netTotal 1 entry,1 matched


HP Switch# display multicast routing-table 20.20.20.1 239.1.1.1 incoming-interface Vlan-interface 20Multicast routing table of VPN-Instance: public netTotal 1 entry,1 matched


HP Switch# display multicast routing-table 20.20.20.1 239.1.1.1 incoming-interface Vlan-interface 20 outgoing-interface Vlan-interface 30Multicast routing table of VPN-Instance: public netTotal 1 entry,1 matched

00001. (20.20.20.2, 239.1.1.1) Uptime: 00:00:20 Upstream Interface: 10


display multicast routing-table show ip mroute


2-194

Display Commandsdisplay multicast routing-table

List of 1 downstream interfaces 1: Vlan-interface30


HP Switch# show ip mrouteIP Multicast Route EntriesTotal number of entries : 2Group Address Source Address Neighbor VLAN--------------- --------------- ----------- ----239.255.255.1 10.27.30.2 10.29.30.1 29239.255.255.5 10.27.30.2 10.29.30.1 29

Operating Notes

For more information, refer to the latest Multicast and Routing Guide for your switch.



2-195

Display Commandsdisplay multicast routing-table static

display multicast routing-table static

Displays the information about multicast static routes.

Field Descriptions

Multicast Routing Table of VPN-Instance: public net: Multicast routing table for the public network

Mroute: Multicast route source address and its mask length

Interface: Outgoing interface to the multicast source

RPF Neighbor: IP address of the RPF neighbor through which the multicast source is reachable

Route-policy: Routing policy. The multicast source address of the route should match the routing policy.

Preference: Route preference

Order: Sequence number of the route

Running Configuration: Command line that configures the multicast static route


display multicast routing-table static show ip pim rpf-override

HP Switch# display multicast routing-table staticMulticast Routing Table of VPN-Instance: n/aRoutes : n/a Mroute 10.10.0.0/16 Interface = n/a RPF Neighbor = 2.2.2.2 Matched routing protocol = <none>, Route-policy = <none> Preference = n/a, Order = n/a Running Configuration = rpf-override 10.10.10.10/32 10.10.10.1


2-196

Display Commandsdisplay multicast routing-table static

Operating Notes

ProVision switches use a different command to define the static multicast routes, The corresponding config command is displayed in the command. For more information on multicast static routes, see the “PIM-SM (Sparse Mode)” or the “PIM-DM (Dense Mode) chapters in the latest Multicast and Routing



display multicast routing-table static Field Mappings.



Multicast Routing Table of VPN-Instance: public net

n/a

Mroute n/a

Interface n/a

RPF Neighbor RPF IP Address

Route-policy n/a

Preference n/a

Order n/a

Running Configuration n/a

HP Switch(config)# show ip pim rpf-override

Static RPF Override

Multicast Source RPF IP Address ------------------- --------------- 10.1.1.1/32 11.2.2.1 13.1.1.1/32 12.1.1.1


2-197

Display Commandsdisplay multicast rpf-info

display multicast rpf-info

Displays rpf override information of a multicast source.

HP Switch# display multicast rpf-info 10.10.10.10 RPF information about source 10.10.10.10: VPN instance: n/a RPF interface: Vlan-Interface 10 Referenced route/mask: 40.40.40.40/32 Referenced route type: n/a Route selection rule: n/a Load splitting rule: n/a



display multicast rpf-info No equivalent ProVision software command


2-198

Display Commandsdisplay ospf cumulative

display ospf cumulative

Displays OSPF statistics information.

Field Descriptions

IO Statistics: Statistics about input/output packets and LSAs.

Type: OSPF packet type.

Input: Packets received.

Output: Packets sent.

Hello: Hello packet.


display ospf cumulative show ip ospf statistics

HP Switch# display ospf cumulative

OSPF Process 1 with Router ID : 2.2.2.2 Cumulations

IO Statistics Type Input Output Hello 2 2 DB Description 0 2 Link-State Req 0 0 Link-State Update 0 0 Link-State Ack 0 0

LSAs originated by this router Router: n/a Network: n/a Sum-Net: n/a Sum-Asbr: n/a External: n/a NSSA: n/a Opq-Link: n/a Opq-Area: n/a Opq-As: n/a

LSAs Originated: n/a LSAs Received: n/a

Routing Table: Intra Area: n/a Inter Area: n/a ASE/NSSA: n/a


2-199


DB Description: Database Description packet

Link-State Req: Link-State Request packet.

Link-State Update: Link-State Update packet.

Link-State-Ack: Link-State Acknowledge packet.

LSAs originated by this router: LSAs originated by this router.

Router: Number of Type-1 LSAs originated.

Network: Number of Type-2 LSAs originated.

Sum-Net: Number of Type-3 LSAs originated.

Sum-Asbr: Number of Type-4 LSAs originated.

External: Number of Type-5 LSAs originated.

NSSA: Number of Type-7 LSAs originated.

Opq-Link: Number of Type-9 LSAs originated.

Opq-Area: Number of Type104 LSAs originated.

Opq-As: Number of Type-11 LSAs originated.

LSA originated: Number of LSAs originated.

LSA Received: Number of LSAs received.

Routing Table: Routing table information.

Intra Area: Intra-area route number.

Inter Area: Inter-area route number.

ASE: ASE route number.

Operating Notes

For more on switch OSPF operation, refer to the “IP Routing” chapter in the latest Multicast and Routing Guide for your switch.


2-200



display ospf cumulative Field Mappings.


HP Switch(ospf)# show ip ospf statistics vlan 1

OSPF statistics for VLAN 1

OSPF Interface Status for 10.0.0.2

Tx Hello Packet Count : 16 Rx Hello Packet Count : 16 Tx DD Packet Count : 2 Rx DD Packet Count : 4 Tx LSR Packet Count : 1 Rx LSR Packet Count : 1 Tx LSU Packet Count : 5 Rx LSU Packet Count : 2 Tx LSA Packet Count : 2 Rx LSA Packet Count : 3

OSPF Errors: 26


Hello TX/RX Hello Packet Count

DB Description n/a

Link-state Req n/a

Link-State Update n/a

Link-State Ack n/a

LSA originated n/a

LSA received n/a

Routing Table fields n/a


2-201

Display Commandsdisplay ospf interface

display ospf interface

Displays OSPF interface information for all OSPF processes.

Field Descriptions

Area: Area ID of the interface.

IP Address: Interface IP address.

Type: Interface network type (PTP, PTMP, Broadcast, or NBMA.

State: Interface state:

• Down: No protocol traffic will be sent or received on the interface.

• Waiting: The interface starts sending and receiving Hello packets and the router is trying to determine the identity of the backup designated router for the network.

• p-2-p: The interface will send Hello packets at the interval of HelloIn-terval, and try to establish an adjacency with the neighbor.

• DR: The router itself is the designated router on the attached network.

• BDR: The router itself is the backup designated router on the attached network.


display ospf interface show ip ospf interface

HP Switch(config)# display ospf interface

OSPF Process 1 with Router ID : 192.168.1.1 Area : 0.0.0.0

IP Address Type State Cost Pri DR BDR --------------- --------- ------- ----- --- --------------- --------------- 192.168.1.1 PTP P-2-P 1562 1 0.0.0.0 0.0.0.0

Area : 0.0.0.1

IP Address Type State Cost Pri DR BDR --------------- --------- ------- ----- --- --------------- --------------- 172.16.0.1 BROADCAST DR 1562 1 172.16.0.1 0.0.0.0


2-202


• DROther: The interface is on a network on which another router is the designated router.

Cost: Interface cost.

Pri: Router priority.

DR: The DR on the interface’s network segment.

BDR: The BDR on the interface’s network segment.

Operating Notes

To enable OSPF operation in ProVision software, use the following command in the global configuration context:

router ospf enable

For more on configuring OSPF, including additional OSPF configuration commands, see the “Configuring OSPF” chapter in the latest Multicast and

Routing Guide for your switch.


OSPF Interface Field Mappings.

HP Switch(config)# show ip ospf interface

OSPF Interface Status

IP Address Status Area ID State Auth-type Cost Pri Passive --------------- -------- --------------- ------- --------- ----- --- ------- 172.16.0.1 enabled backbone DR none 1562 1 no


Area Area ID

IP Address IP Address

n/a Status

Type n/a

State State

n/a Auth-Type

Cost Cost


2-203



PRI PRI

n/a Passive

DR n/a

BDR n/a



2-204

Display Commandsdisplay ospf lsdb

display ospf lsdb

Displays OSPF link state database information.

Field Descriptions

Area: LSDB information of the area

Type: LSA type

LinkState ID: Linkstate ID

AdvRouter: The router that advertised the LSA

Age: Age of the LSA

Len: Length of the LSA


display ospf lsdb show ip ospf link-stateshow ip ospf external-link-state

HP Switch# display ospf lsdb

OSPF Process 1 with Router ID 7.7.7.7 Link State Database

Area: 0.0.0.0 Type LinkState ID AdvRouter Age Len Sequence Metric Router 11.0.9.2 11.0.9.2 930 n/a 80000005 n/a Router 11.0.9.1 11.0.9.1 456 n/a 80000004 n/a Network 11.0.9.2 11.0.9.2 930 n/a 80000002 n/a Sum-Net 1.2.4.0 11.0.9.1 16 n/a 80000001 n/a Area: 0.0.0.1 Type LinkState ID AdvRouter Age Len Sequence Metric Router 11.0.9.1 11.0.9.1 9 n/a 80000003 n/a Router 100.0.9.4 100.0.9.4 10 n/a 80000004 n/a Network 1.2.4.6 100.0.9.4 5 n/a 80000002 n/a Sum-Net 11.0.9.0 11.0.9.1 16 n/a 80000001 n/a

AS External Database Type LinkState ID AdvRouter Age Len Sequence Metric External 192.168.1.0 3.3.3.3 406 n/a 80000006 n/a[bot-ospf-1-area-0.0.0.1]


2-205


Sequence: Sequence number of the LSA

Metric: Cost of the LSA

Operating Notes



display ospf lsdb Field Mappings.

HP Switch# show ip ospf link-state

OSPF Link State Database for Area 0.0.0.0 Advertising LSA Type Link State ID Router ID Age Sequence # Checksum ---------- --------------- --------------- ---- ----------- ---------- Router 10.0.8.32 10.0.8.32 65 0x80000281 0x0000a7b6 Router 10.0.8.33 10.0.8.33 1638 0x80000005 0x0000a7c8 Network 10.3.2.37 10.0.8.37 1695 0x80000006 0x00000443 Summary 10.3.16.0 10.0.8.33 1638 0x80000007 0x0000c242 Summary 10.3.16.0 10.0.8.35 1316 0x80000008 0x0000aa58 Summary 10.3.17.0 10.0.8.33 1638 0x8000027b 0x0000becf Summary 10.3.17.0 10.0.8.35 1316 0x80000008 0x0000a957 AsbSummary 10.0.8.36 10.0.8.33 1412 0x80000002 0x00002cba OSPF Link State Database for Area 10.3.16.0 Advertising LSA Type Link State ID Router ID Age Sequence # Checksum ---------- --------------- --------------- ---- ----------- ---------- Router 10.0.8.33 10.0.8.33 1727 0x8000027e 0x0000d53c Router 10.0.8.34 10.0.8.34 1420 0x80000283 0x0000de4f Network 10.3.16.34 10.0.8.34 1735 0x80000005 0x00001465


Area Area

Type LSA Type


2-206



LinkState ID Link State ID

AdvRouter Router ID

Age Age

Len n/a

Sequence Sequence

Metric n/a



2-207

Display Commandsdisplay ospf peer

display ospf peer

Displays information about OSPF neighbors.

Field Descriptions

Area: Neighbor area.

Router ID: Neighbor router ID

Address: Neighbor interface address.

Pri: Neighboring router priority.

Dead-Time: Dead interval remained.

Interface: Interface connected to the neighbor.

State: Neighbor state: Down, Init, Attempt, 2-Way, Exstart, Exchange, DR/BDR state, Loading or Full.

Operating Notes



display ospf peer show ip ospf neighbor

HP Switch# display ospf peer

OSPF Process 1 with Router ID 1.1.1.1 Neighbor Brief Information Area: 0.0.0.0

Router ID Address Pri Dead-Time Interface State 1.1.1.2 1.1.1.2 1 40 Vlan11 Full/DR


2-208

Display Commandsdisplay ospf peer


display ospf peer Field Mappings.


HP Switch(config)# show ip ospf neighbor

OSPF Neighbor Information Rxmt Helper Router ID Pri IP Address NbIfState State QLen Events Status --------------- --- -------------- --------- --------- ----- ------ ------ 10.0.8.34 1 10.3.18.34 DR FULL 0 6 none 10.3.53.38 1 10.3.53.38 DR FULL 0 6 none


Area n/a

Router ID Router ID

Address IP Address

Pri Pri

Dead-Time Dead Timer Expires

Interface n/a

State NbIfState/State


2-209

Display Commandsdisplay ospf routing

display ospf routing

Displays OSPF routing information for all OSPF processes.

Field Descriptions

Destination: Destination network.

Cost: Cost to destination.

Type: Route type (intra-area, transit, stub, inter-area, type 1 external, type 2 external.

NextHop: Next hop address.

AdvRouter: Advertising router.

Area: Area ID.

Total Nets: Total networks.

Intra Area: Total intra-area routes.

Inter Area: Total inter-area routes.

ASE: Total ASE routes.

NSSA: Total NSSA routes.


display ospf routing show ip ospf

HP Switch(config)# display ospf routing

OSPF Process 1 with Router ID 192.168.1.2 Routing Tables Routing for Network Destination Cost Type NextHop AdvRouter Area 192.168.1.0/24 1562 Stub 192.168.1.2 192.168.1.2 0.0.0.0 172.16.0.0/16 1563 Inter 192.168.1.1 192.168.1.1 0.0.0.0

Total Nets: 2

Intra Area: 1 Inter Area: 1 ASE: 0 NSSA: 0


2-210

Display Commandsdisplay ospf routing

Operating Notes


router ospf enable

For more on configuring OSPF, including additional OSPF configuration commands, see the “Configuring OSPF” chapter in the latest Multicast and

Routing Guide for your switch.



2-211

Display Commandsdisplay ospf vlink

display ospf vlink

Displays OSPF virtual link information.

HP Switch# display ospf vlink OSPF Process 1 with Router ID 3.3.3.3 Virtual Links Virtual-link Neighbor-ID -> 2.2.2.2, Neighbor-State: Full Interface: 10.1.2.1 (Vlan-interface11) Cost: 1562 State: P-2-P Type: Virtual Transit Area: 0.0.0.1 Timers: Hello 10 , Dead 40 , Retransmit 5 , Transmit Delay 1

Field Descriptions

Virtual-link Neighbor-ID: ID of the neighbor connected to the router via the virtual link.

Neighbor-State: Neighbor’s operating state (Down, Init, 2-Way, ExStart, Exchange, Loading Full).

Interface: Local interface’s IP address and name of the virtual link.

Cost: Interface route cost.

State: Interface state.

Type: Link type (virtual link).

Transit Area: Transit area ID.

Timers: Values of the hello, dead, poll (NBMA), retransmit, and interface transmission delay timers.

Operating Notes


router ospf enable

Comware Related ProVision Software

display ospf vlink show ip ospf virtual-link


2-212

Display Commandsdisplay ospf vlink

For more on configuring OSPF, including virtual links and other OSPF opera-tion, see the “Configuring OSPF” chapter in the latest Multicast and Routing



ospf vlink Field Mappings.


HP Switch(config)# show ip ospf virtual-link

OSPF Virtual Interface Status

Transit AreaID Neighbor Router Authentication Interface State --------------- --------------- --------------- --------------- 0.0.0.1 2.2.2.2 none P2P


Virtual-link Neighbor ID Neighbor Router

Neighbor-State Interface State

Interface n/a

Cost n/a

State n/a

Transit Area Transit AreaID

Timers n/a

n/a Authentication


2-213

Display Commandsdisplay ospfv3

display ospfv3

Displays brief information about OSPFv3.

HP Switch# display ospfv3 Routing Process "OSPFv3 (1)" with ID 3.3.3.3 Graceful restart restarter disabled Graceful restart helper enabled Graceful restart helper strict-lsa-checking disabled Graceful restart interval n/a SPF schedule delay 5 secs, Hold time between SPFs 10 secs Minimum LSA interval n/a, Minimum LSA arrival n/a Number of external LSA 1. These external LSAs' checksum Sum 0x7741 Number of AS-Scoped Unknown LSA 0 Number of LSA originated 4 Number of LSA received 0 Number of areas in this router is 2 Area BACKBONE(0) Number of interfaces in this area is 1 SPF algorithm executed 0 times Number of LSA 0. These LSAs' checksum Sum 0x0000 Number of Unknown LSA 0 Area 0.0.0.1 Number of interfaces in this area is 1 SPF algorithm executed 9 times Number of LSA 2. These LSAs' checksum Sum 0x1A56A Number of Unknown LSA 0


HP Switch# show ipv6 ospf3 generalOSPFv3 General StatusOSPFv3 protocol :enabledRouter ID :10.10.10.80...Nonstop forwarding : EnabledGraceful Restart Interval : 500Graceful Restart Helper Mode : Enabled...


display ospfv3 show ipv6 ospf3


2-214

Display Commandsdisplay ospfv3

Operating Notes





2-215

Display Commandsdisplay ospfv3 area area-id peer interface interface-type interface number

display ospfv3 area area-id peer interface interface-type interface number

Displays OSPFv3 neighbor information.

Field Descriptions

Neighbor ID: Router ID of a neighbor

Pri: Priority of neighbor router

State: Neighbor state

Dead Time: Dead time remained

Interface: Interface connected to the neighbor

Instance ID: Instance ID

Operating Notes

For more on switch OSPFv3 operation, refer to the “OSPFv3 Routing” chapter in the latest IPv6 Configuration Guide for your switch.



display ospfv3 area area-id peer interface interface-type interface number


HP Switch# display ospfv3 area 0 peer Vlan-interface 1 OSPFv3 (Process 1)

OSPFv3 Area (0.0.0.0)

Neighbor ID Pri State Dead Time Interface Instance ID1.1.1.1 1 Full 00:00:35 Vlan1 0


2-216

Display Commandsdisplay ospfv3 area area-id peer peer-router-id

display ospfv3 area area-id peer peer-router-id

Displays OSPFv3 neighbor information for the specified area.

Field Descriptions

Neighbor: Neighbor ID.

Interface Address: Interface Address.

In the area: The area address.

Vlan-interface: Vlan-interface <vid> belongs to area <area>.

DR/BDR: Router Id of the Designated Router and the Backup Designated Router.

Options: Displays the capabilities.

Dead timer: Indicates when the dead timer is due.

Neighbor up: Neighbor has been up for the indicated time.

Database Summary List: Number of LSAs sent in the DD packet.

Link State Request List: Number of LSAs in the link state request list.


display ospfv3 area area-id peer peer-router-id

show ipv6 ospf3 neighbor <ip-addr> detail

HP Switch(config)# display ospfv3 area 0 peer 1.1.1.1 OSPFv3 Process (1) Neighbor 1.1.1.1 is Full, interface address FE80::21B:3FFF:FEF7:DEC0 In the area 0.0.0.0 via interface Vlan-interface1 DR is 2.2.2.2 BDR is 1.1.1.1 Options is 0x000013 (-|R|-|-|E|V6) Dead timer due in 00:00:35 Neighbor is up for 00:03:51 Database Summary List 0 Link State Request List 0 Link State Retransmission List 0 Graceful restart state: Normal


2-217


Link State Retransmission List: Number of LSAs in the link state retransmission list.

Graceful restart state: Graceful restart status can be:

• Normal: Normal status

• Helper: The device is a Graceful Restart Helper of the neighbor.

Operating Notes



display ospfv3 area area-id peer peer-id Field Mappings.

HP Switch(ospf3)# show ipv6 ospf3 neighbor 15.1.0.1 detail

OSPFv3 Neighbor Information for neighbor 15.1.0.1

IPv6 Address : fe80::55:1 Router ID : 15.1.0.1 State : FULL Interface : vlan-55 Designated Router : 15.1.0.1 Area : 0.0.0.1 Backup Designated Router : 15.1.0.4 Priority : 1 Retransmit Queue Length : 0 Options : 19 Neighbor Uptime : 1days Events : 0 Dead Timer Expires : 33 sec


Neighbor Neighbor

Interface Address IPv6 Address

In the area Area ID

Vlan-interface Interface

DR/BDR Designated Router/Backup Designated Router

Options Options

Dead timer Dead Timer expires

Neighbor up Neighbor Uptime

Database Summary List n/a


2-218



Link State Request n/a

Link State Retransmission List

Retransmit Queue Length

Graceful Restart n/a



2-219

Display Commandsdisplay ospfv3 area area-id peer verbose

display ospfv3 area area-id peer verbose

Displays detailed information about OSPFv3 neighbors for a specified area.

Field Descriptions



In the area: The area address.


DR/BDR: Router Id of the Designated Router and Backup Designated Router.








display ospfv3 area area-id peer verbose No equivalent ProVision software command

HP Switch(config)# display ospfv3 area 1 peer verbose

Neighbor 3.3.3.3 is Full, interface address FE80::221:F7FF:FE1B:EC80 In the area 0.0.0.1 via interface Vlan-interface2 DR is 3.3.3.3 BDR is 2.2.2.2 Options is 0x000013 (-|R|-|-|E|V6) Dead timer due in 00:00:34 Neighbor is up for 00:01:44 Database Summary List 0 Link State Request List 0 Link State Retransmission List 0 Graceful restart state: Normal


2-220

Display Commandsdisplay ospfv3 area area-id peer verbose




Operating Notes




2-221

Display Commandsdisplay ospfv3 interface

display ospfv3 interface

Displays OSPF interface information for all OSPF processes.

N o t e Only one process is supported, so the process number is always 1.

Field Descriptions

Interface ID: Interface ID

IPv6 Prefixes: IPv6 Prefix

OSPF Process: OSPF process

Area: Area ID of the interface.

Instance ID: Instance ID

Router ID: Router ID

Network Type: Network type of the interface (PTP, PTMP, Broadcast, or NBMA).


display ospfv3 interface show ipv6 ospf3 interface

HP Switch(config)# display ospf3 interface Vlan-interface4 is down, line protocol is up Interface ID vlan-4 IPv6 Prefixes 1234::2/96 (Link-Local Address): OSPFv3 Process (1), Area 0.0.0.4 Instance ID 0 Router ID: 0.0.0.40 Network Type: BROADCAST, Cost: 1 Transmit Delay is 1 sec, State: DR Priority: 1 Designated Router (ID) 2001:db8:0:5::10:1/64 Interface Address: FE80::212:79FF:FE88:4D00 Backup Designated Router (ID): 2001:db8:0:5::10:2/64 Interface Address: FE80::218:71FF:FEC4:F00 Timer interval configured, Hello: 10 Dead: 40 Wait: 40 Retransmit: 5 Hello due in 00:00:09 Neighbor Count is 0 Adjacent neighbor count is 0


2-222


Cost: Cost value of the interface.

Transmit Delay: Transmission delay of the interface.

State: Interface state:

• Down: No protocol traffic will be sent or received on the interface.

• Waiting: In this state, the router is trying to determine the identity of the (Backup) Designated Router for this network.

• p-2-p: The interface is in point-to-point state and will skip the waiting period and DR/BDR election.

• DR: The router itself is the designated router on the attached network.

• BDR: The router itself is the backup designated router on the attached network.

• DROther: The interface is neither a Designated Router nor a backup Designated Router.

Priority: Router priority for the DR/BDR election.

Designated Router: The DR on the interface’s network segment.

Backup Designated Router: The BDR on the interface’s network segment.

Time Interval Configured: Time interval in seconds configured on the interface:

• Hello—Hello interval.

• Dead—Dead interval.

• Wait—After this timer expires, the interface quits from the waiting state.

• Retransmit—LSA retransmission interval.

Hello due in: Hello packet will be sent in the indicated number of seconds.

Neighbor Count: Number of neighbors on the interface.

Adjacent Neighbor Count: Number of adjacencies on the interface.

Operating Notes

To enable OSPF operation in ProVision software, enter the following com-mands in the global configuration context:

ipv6 unicast-routing

router ospf3 enable


2-223


For more on configuring OSPFv3, including additional OSPFv3 configuration commands, see the “OSPFv3 Routing” chapter in the latest IPv6 Configura-

tion Guide for your switch.


OSPF Interface Field Mappings.

HP Switch(config)# show ipv6 ospf3 interface 75 detail

OSPFv3 configuration and statistics for VLAN 75

Interface : vlan-75 Status : Enabled Area ID : 0.0.0.3 State : WAIT Priority : 1 Cost : 1 Type : BCAST Passive : Yes Hello Interval : 10 Dead Interval : 40 Transit Delay : 1 Retransmit Interval : 5 Events : 0 Designated Router : 15.1.1.2 Neighbors : 1 Backup Designated Router : 15.1.4.4


Interface ID Interface

n/a Status

IPv6 Prefixes n/a

OSPF Process n/a

Area Area ID

Instance ID n/a

Router ID n/a

Network Type Type

Cost Cost

Transmit Delay Transit Delay

State State

Priority Priority

Designated Router Designated Router

Backup Designated Router Backup Desig. Rtr


2-224



n/a Passive

Time Interval Configured Retransmit Interval

Hello due in n/a

Neighbor Count Neighbors

Adjacent Neighbor Count n/a



2-225

Display Commandsdisplay ospfv3 lsdb

display ospfv3 lsdb

Displays OSPFv3 LSDB information. This command is available only in man-ager mode.

HP Switch# display ospfv3 lsdb OSPFv3 Router with ID (2.2.2.2) (Process 1) Link-LSA (Interface Vlan-interface1)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Prefix5.178.0.0 1.1.1.1 1082 0x8000000c 0x31c7 15.178.0.0 2.2.2.2 0896 0x8000000b 0xe23c 1

Link-LSA (Interface Vlan-interface2)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Prefix5.178.0.1 2.2.2.2 0896 0x8000000b 0x0f0d 15.178.0.1 3.3.3.3 0654 0x8000000b 0xcf90 1

Router-LSA (Area 0.0.0.0)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Link0.0.0.0 1.1.1.1 0892 0x8000000e 0x8e0c 10.0.0.0 2.2.2.2 0376 0x8000000d 0x7b19 1

Network-LSA (Area 0.0.0.0)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum 5.178.0.0 1.1.1.1 0887 0x80000016 0xcc7f

Inter-Area-Prefix-LSA (Area 0.0.0.0)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum0.0.0.1 2.2.2.2 0886 0x8000000b 0x7962

Intra-Area-Prefix-LSA (Area 0.0.0.0)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Prefix Reference0.0.0.2 1.1.1.1 0892 0x8000000b 0x05ee 1 Network-LSA

Router-LSA (Area 0.0.0.1)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Link0.0.0.0 2.2.2.2 0376 0x80000010 0xe7a3 10.0.0.0 3.3.3.3 0649 0x8000000c 0xc8c5 1

Network-LSA (Area 0.0.0.1)


display ospfv3 lsdb show ipv6 ospf3 link-state


2-226

Display Commandsdisplay ospfv3 lsdb

---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum5.178.0.1 2.2.2.2 0371 0x80000018 0xf448

Inter-Area-Prefix-LSA (Area 0.0.0.1)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum0.0.0.1 2.2.2.2 0891 0x8000000b 0x6d6f

Intra-Area-Prefix-LSA (Area 0.0.0.1)---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum Prefix Reference0.0.0.2 2.2.2.2 0651 0x8000000b 0x37b2 1 Network-LSA

AS-external-LSA---------------------------------------------------------------------Link State ID Origin Router Age SeqNum CkSum0.0.0.1 2.2.2.2 0375 0x8000000b 0x999a0.0.0.2 2.2.2.2 0570 0x80000002 0x6ebc



2-227

Display Commandsdisplay ospfv3 lsdb statistics

display ospfv3 lsdb statistics

Displays LSA statistics in the OSPFv3 LSDB. This command is available only in manager mode.

HP Switch# display ospfv3 lsdb statistics OSPFv3 Router with ID (2.2.2.2) (Process 1) LSA Statistics --------------------------------------------------------------------- Area ID Router Network IntePre InteRou IntraPre Link Grace ASE 0.0.0.0 5 5 5 5 5 0.0.0.1 5 5 5 5 5 Total 10 10 10 10 10 5 0 5



display ospfv3 lsdb statistics No equivalent ProVision software command


2-228

Display Commandsdisplay ospfv3 peer

display ospfv3 peer

Displays OSPFv3 neighbor information.

Field Descriptions

Neighbor ID: Router ID of a neighbor.

Pri: Priority of neighbor router for DR/BDR election.

State: Neighbor state.

Dead time: Dead time remaining

Interface: Interface connected to the neighbor.

Instance ID: Instance ID.

Operating Notes



display ospfv3 peer show ipv6 ospf3 neighbor

HP Switch(vlan-2)# display ospfv3 peer

OSPFv3 Area ID 0.0.0.1 (Process 1)

Neighbor ID Pri State Dead Time Interface Instance ID -------------------------------------------------------------------------- 120.85.228.88 1 FULL 00:00:33 Vlan2 0


2-229

Display Commandsdisplay ospfv3 peer


display ospfv3 peer Field Mappings.


HP Switch(ospf3)# show ipv6 ospf3 neighbor

OSPFv3 Neighbor Information

Interface Router ID Pri State Rxmt QLen Events --------- --------------- ----- ---------- ---------- ---------- Vlan-55 15.1.0.1 1 Full 0 0 Vlan-75 15.1.1.2 1 Full 0 0 tunnel-3 4.3.2.1 1 Full 0 0


Neighbor ID Router ID

Interface Interface

n/a Router ID

Pri Pri

State State

Dead time n/a

Instance ID n/a

n/a Rxmt QLen

n/a Events


2-230

Display Commandsdisplay ospfv3 peer peer-router-id

display ospfv3 peer peer-router-id

Displays the router ID of the specified neighbor.

Field Descriptions




DR/BDR: Router Id of the Designated Router and the Backup Designated Router.








display ospfv3 peer peer-router-id show ipv6 ospf3 neighbor <router-id> detail

HP Switch# display ospfv3 peer 2.2.2.2 Neighbor 2.2.2.2 is Full, interface address FE80::223:89FF:FECB:6FDC In the area 0.0.0.0 via interface Vlan-interface1 DR is 2.2.2.2 BDR is 1.1.1.1 Options is 0x000013 (-|R|-|-|E|V6) Dead timer due in 00:00:35 Neighbor is up for 00:04:35 Database Summary List 0 Link State Request List 0 Link State Retransmission List 0 Graceful restart state: Normal


2-231





Operating Notes



display ospfv3 peer verbose Field Mappings.





Neighbor Neighbor




Options Options








2-232






2-233

Display Commandsdisplay ospfv3 peer statistics

display ospfv3 peer statistics

Displays information about all OSPFv3 neighbors on the router, that is, number of neighbors in different states.

HP Switch# display ospfv3 peer statistics OSPFv3 Router with ID (2.2.2.2) (Process 1) Neighbor Statistics---------------------------------------------------------------------Area ID Down Attempt Init 2-Way ExStart Exchange Loading Full0.0.0.0 0 0 0 0 0 0 0 10.0.0.1 0 0 0 0 0 0 0 1Total 0 0 0 0 0 0 0 2



display ospfv3 peer statistics No equivalent ProVision software command


2-234

Display Commandsdisplay ospfv3 peer verbose

display ospfv3 peer verbose

Displays detailed information about OSPFv3 neighbors.

Field Descriptions




DR/BDR: Router-Id of the Designated Router and the Backup Designated Router.








display ospfv3 peer verbose show ipv6 ospf3 neighbor detail

HP Switch# display ospfv3 peer verbose

Neighbor 2.2.2.2 is Full, interface address FE80::223:89FF:FECB:6FDC In the area 0.0.0.0 via interface Vlan-interface1 DR is 2.2.2.2 BDR is 1.1.1.1 Options is 0x000013 (-|R|-|-|E|V6) Dead timer due in 00:00:30 Neighbor is up for 00:00:20 Database Summary List 0 Link State Request List 0 Link State Retransmission List 0 Graceful restart state: Normal


2-235





Operating Notes



display ospfv3 peer verbose Field Mappings.





Neighbor Neighbor




Options Options








2-236






2-237

Display Commandsdisplay ospfv3 statistic

display ospfv3 statistic

Displays outbound/inbound OSPFv3 packet statistics on associated inter-face(s).

Field Descriptions

Interface: Interface name.

Instance: Instance number.

Type: Type of packet.

Input: Number of packets received by the interface.

Output: Number of packets sent by the interface.

Hello: Hello packet.

DB Description: Database description packet.

Ls Req: Link state request packet

Ls Upd: Link state update packet

Ls Ack: Link state acknowledgement packet

Discarded: Number of discarded packets.


display ospfv3 statistic show ipv6 ospf3 statistics

HP Switch(vlan-2)# display ospfv3 statistics

OSPFv3 Statistics Interface 2 Instance 0 Type Input Output Hello 6 10 DB Description 2 5 Ls Req 1 1 Ls Upd 2 3 Ls Ack 2 2 Discarded 32 1


2-238


Operating Notes



Per-VLAN OSPF Statistics

Field Content

OSPF statistics for VLAN <vlan-id>

OSPF statistics displayed for the specified VLAN number

OSPF Interface Status for <ip-address>

IP address of a subnet on the VLAN

Tx/Rx Hello Packet Count

Number of OSPF hello packets sent/received on each subnet interface

Tx/Rx DD Packet Count

Number of link-state database description packets sent/received on each subnet interface

Tx/Rx LSR Packet Count

Number of link-state request packets sent/received on each subnet interface

Tx/Rx LSU Packet Count

Number of link-state update packets sent/received on each subnet interface

Tx/Rx LSA Packet Count

Number of link-state acknowledgement packets sent/received on each subnet interface

OSPF errors Number of errors detected on the VLAN subnet during OSPF packet exchange


2-239


display ospfv3 statistic Field Mappings.


HP Switch# show ipv6 ospf3 statistics vlan 55

OSPFv3 statistics for VLAN 55

Tx Hello Packets : 26005 Rx Hello Packets : 26005 Tx DD Packets : 3 Rx DD Packets : 3 Tx LSR Packets : 1 Rx LSR Packets : 1 Tx LSU Packets : 1436 Rx LSU Packets : 1046 Tx LSA Packets : 615 Rx LSA Packets : 1444

OSPFv3 Errors : 0


Interface OSPF statistics for

Instance n/a

Type n/a

Input n/a

Output n/a

Hello Tx/Rx Hello Packets

DB Description Tx/Rx DD Packets

Ls Req Tx/Rx LSR Packets

Ls Upd Tx/Rx LSU Packets

Ls Ack Tx/Rx LSA Packets

Discarded Total Errors


2-240

Display Commandsdisplay ospfv3 vlink

display ospfv3 vlink

Displays OSPFv3 virtual link information.

Field Descriptions

Virtual Link: The virtual link name and destination router ID.

Transit area: The VLAN interface ID and transit area.

Instance ID: Instance identity.

Local address: The local router IPv6 address.

Remote address: The remote router IPv6 address.

Transmit Delay: The transmit delay for sending LSAs.

State: The state of the interface, such as P-To-P.

Timer intervals: The configured timer intervals for Hello, Dead, Wait, and Retransmit.

Hello due in: The interval until the next Hello packet is sent.

Adjacency state: The current virtual neighbor adjacency state


display ospfv3 vlink show ipv6 ospf3 virtual-link ?

HP Switch# display ospfv3 vlink

Virtual Link VLINK1 to router 1.1.1.1 is up

Transit area :0.0.0.1 via interface Vlan-interface11, instance ID: 0

Local address: 2000:1::1

Remote address: 2001:1:1::1

Transmit Delay is 1 sec, State: P-To-P,

Timer intervals configured, Hello: 10, Dead: 40, Wait: 40, Retransmit: 5

Hello due in 00:00:02

Adjacency state :Full


2-241

Display Commandsdisplay ospfv3 vlink

Operating Notes

To configure OSPFv3 operation in ProVision software, see the “OSPFv3 Routing” chapter in the latest IPv6 Configuration Guide for your switch.


HP Switch(config)# show ipv6 ospf3 virtual-link

OSPFv3 Virtual Interface Status

Transit AreaID Neighbor Router Interface State

--------------- --------------- --------------- 0.0.0.1 1.1.1.1 P2P

ospfv3 vlink Field Mappings.



Virtual Link Neighbor Router

Transit area Transit AreaID

Local address n/a

Remote address n/a

Transmit Delay n/a

State Interface State

Timer intervals n/a

Hello due n/a

Adjacency state n/a


2-242

Display Commandsdisplay pim bsr-info

display pim bsr-info

Displays the BSR information in the PIM domain and the locally configured C-RP information in effect.

Field Descriptions

VPN-Instance: public net: Public network.

Elected BSR Address: Address of the elected BSR.

Candidate BSR Address: Address of the candidate BSR.

Priority: BSR priority.


display pim bsr-info show ip pim bsr

HP Switch# display pim bsr-info Elected BSR Address : 10.10.10.11 Priority : 0 Hash mask length : 30 State: n/a Scope: n/a Uptime : 00:08:00 Next BSR message scheduled at : 01:20:00 Candidate BSR Address : 10.10.10.10 Priority : 0 Hash mask length : 30 State: n/a Scope: n/a Candidate RP: 10.10.10.10(Vlan-interface10) Priority : 192 HoldTime : 192 Advertisement Interval : 192 Next advertisement scheduled at: n/a Candidate RP: 10.10.10.10(Vlan-interface20) Priority : 192 HoldTime : 192 Advertisement Interval : 192 Next advertisement scheduled at: n/a Candidate RP: 10.10.10.10(Vlan-interface30) Priority : 192 HoldTime : 192 Advertisement Interval : 192 Next advertisement scheduled at: n/a


2-243


Hash mask length: Hash mask length.

State: BSR state.

Scope: Scope of the BSR.

Uptime: Length of time for which this BSR has been up, in hh:mm:ss.

Next BSR message scheduled at: Length of time in which the BSR will expire, in hh:mm:ss.

Candidate RP: Address of the C-RP.

Priority: Priority of the C-RP.

HoldTime: Timeout time of the C-RP.

Advertisement Interval: Interval at which the C-RP sends advertisement mes-sages.

Next advertisement scheduled at: Length of time in which the C-RP will send the next advertisement message, in hh:mm:ss.

Operating Notes

For more information on PIM, see the “PIM-SM (Sparse Mode)” or the “PIM-DM (Dense Mode) chapters in the latest Multicast and Routing Guide for your switch.


2-244



display pim bsr-info Field Mappings.

HP Switch(config)# show ip pim bsr

Status and Counters - PIM-SM Bootstrap Router Information

E-BSR Address : 10.10.10.2 E-BSR Priority : 0 E-BSR Hash Mask Length : 30 E-BSR Up Time : 53 mins Next Bootstrap Message : 88 secs

C-BSR Admin Status : This system is a Candidate-BSR C-BSR Address : 10.10.10.1 C-BSR Priority : 0 C-BSR Hash Mask Length : 30 C-BSR Message Interval : 60 C-BSR Source IP VLAN : 100

C-RP Admin Status : This system is a Candidate-RP C-RP Address : 10.10.10.1 C-RP Hold Time : 150 C-RP Advertise Period : 60 C-RP Priority : 192 C-RP Source IP VLAN : 100

Group Address Group Mask --------------- --------------- 224.0.0.0 240.0.0.0 229.0.1.0 255.255.255.0 239.100.128.0 255.255.128.0

Elected BSR for the PIM-SM Domain

Candidate-BSR Configuration for the Current Routing Switch

Candidate-RP Configuration for the Current Routing Switch

Multicast Groups for which the Current Routing Switch Is Configured as a Candidate-RP


VPN-Instance public net n/a

Elected BSR Address E-BSR Address

Candidate BSR Address C-BSR Address

Priority E-BSR Priority

Hash mask length E-BSR Hash Mask Length


2-245



State n/a

Scope n/a

Uptime E-BSR Uptime

Next BSR messaged scheduled at Next Bootstrap Message

Candidate RP C-RP Address

Priority C-RP Priority

HoldTime C-RP Hold Time

Advertisement Interval C-RP Advertise Period

Next advertisement scheduled at n/a



2-246

Display Commandsdisplay pim control-message counters

display pim control-message counters

Displays statistics information of PIM control messages.

HP Switch# display pim control-message countersVPN-Instance: n/a PIM global control-message counters: Received Sent Invalid Register 0 0 0 Register-Stop 0 0 0 Probe n/a n/a n/a

PIM control-message counters for interface: Vlan-interface10 Received Sent Invalid Assert 0 0 0 Graft 0 0 0 Graft-Ack 0 0 0 Hello 0 0 0 Join/Prune 0 0 0 State-Refresh 0 0 0 BSR 0 0 0 C-RP 0 0 0

PIM control-message counters for interface: Vlan-interface30 Received Sent Invalid Assert 0 0 0 Graft 0 0 0 Graft-Ack 0 0 0 Hello 0 0 0 Join/Prune 0 0 0 State-Refresh 0 0 0 BSR 0 0 0 C-RP 0 0 0



display pim control-message counters No equivalent ProVision software command


2-247

Display Commandsdisplay pim grafts

display pim grafts

Displays information about unacknowledged PIM-DM graft messages.

HP Switch# display pim grafts

vlan 1 name "DEFAULT_VLAN" no untagged 1-2,48 untagged 3-47 ip address dhcp-bootp exit

vlan 10 name "VLAN10" untagged 1,48 ip address 10.10.10.3 255.255.255.0 ip igmp exit

vlan 30 name "VLAN30" untagged 2 ip address 30.30.30.2 255.255.255.0 ip igmp ip rip 30.30.30.2 ip pim-sparse ip-addr any exit exit



display pim grafts No equivalent ProVision software command


2-248

Display Commandsdisplay pim interface

display pim interface

Displays the PIM information on the specified interface or all interfaces.

Field Descriptions

VPN-Instance: public net: Public network.

Interface: Interface name.

NbrCnt: Number of PIM neighbors.

HelloInt: Hello interval.

DR-Pri: Priority for DR election.

DR-Address: DR IP address, where “local” indicates a local address

Operating Notes



display pim interface <interface> show ip pim interface

HP Switch# display pim interfaceVPN-Instance: n/aInterface NbrCnt HelloInt DR-Pri DR-AddressVlan10 n/a 30 1 10.10.10.11Vlan20 n/a 30 1 20.20.20.20Vlan30 n/a 30 1 30.30.30.30


2-249

Display Commandsdisplay pim interface


display pim interface Field Mappings.




Interface VLAN

NbrCnt n/a

HelloInt n/a

DR-Pri n/a

DR-Address IP Address

n/a Mode

HP Switch(config)# show ip pim interface

PIM Interfaces

VLAN IP Address Mode ---- --------------- ------------ 1 10.1.10.1 sparse 2 10.2.10.1 sparse


2-250

Display Commandsdisplay pim interface verbose

display pim interface verbose

Displays detailed PIM information.

Field Descriptions

VPN-Instance Public net: Public network.

Interface: Interface name and its IP address.

PIM version: Running PIM version.

PIM mode: PIM mode, dense or sparse.


display pim interface verbose show ip pim interface <int>

HP Switch# display pim interface verboseInterface : Vlan-interface10, 10.10.10.10 PIM version : n/a PIM mode : 2 PIM DR : 10.10.10.10 PIM DR Priority (configured) : 1 PIM neighbor count: n/a PIM hello interval : 30 PIM LAN delay (negotiated): n/a PIM LAN delay (configured) : 500 PIM override interval (negotiated): n/a PIM override interval (configured) : 2500 PIM neighbor tracking (negotiated): n/a PIM neighbor tracking (configured): n/a PIM generation ID : 2 PIM require generation ID: n/a PIM hello hold interval : 105 PIM assert hold interval: n/a PIM triggered hello delay : 5 PIM J/P interval : 60 PIM J/P hold interval: n/a PIM state-refresh processing : 1 PIM state-refresh interval : 0 PIM state-refresh rate limit: n/a PIM state-refresh TTL : 0 PIM graft retry interval : 3 Number of routers on network not using DR priority: n/a Number of routers on network not using LAN delay: n/a Number of routers on network not using neighbor tracking: n/a


2-251


PIM DR: DR IP address.

PIM DR Priority (configured): Configured priority for DR election.

PIM neighbor count: Total number of PIM neighbors.

PIM hello interval: Hello interval.

PIM LAN delay (negotiated): Negotiated prune message delay.

PIM LAN delay (configured): Configured prune message delay.

PIM override interval (negotiated): Negotiated prune override interval.

PIM override interval (configured): Configured prune override interval.

PIM neighbor tracking (negotiated): Negotiated neighbor tracking status (enabled/disabled).

PIM neighbor tracking (configured): Configured neighbor tracking status (enabled/disabled).

PIM generation ID: Generation_ID value.

PIM require generation ID: Rejection of Hello messages without Generation_ID (enabled/disabled).

PIM hello hold interval: PIM neighbor timeout time.

PIM assert hold interval: Assert timeout time.

PIM triggered hello delay: Maximum delay of sending hello messages.

PIM J/P interval: Join/prune interval.

PIM J/P hold interval: Join/prune timeout time.

PIM BSR domain border: Status of PIM domain border configuration (enabled/disabled).

Number of routers on network not using DR priority: Number of routers not using the DR priority field on the subnet where the interface resides.

Number of routers on network not using LAN delay: Number of routers not using the LAN delay field on the subnet where the interface resides.

Number of routers on network not using neighbor tracking: Number of routers not using neighbor tracking on the subnet where the interface resides.


2-252


Operating Notes



display pim interface Field Mappings.

HP Switch(config)# show ip pim interface 1

PIM Interface

VLAN : 1 IP Address : 10.1.10.1 Mode : sparse

Designated Router : 10.1.10.1

Hello Interval (sec) : 30 Hello Delay (sec) : 5

Override Interval (msec) : 2500 Lan Prune Delay : Yes Propagation Delay (msec) : 500 Lan Delay Enabled : No Neighbour Timeout : 180 DR Priority : 1



Interface VLAN

PIM Version n/a

PIM mode Mode

PIM DR Designated Router

PIM DR Priority (configured) DR Priority

PIM neighbor count n/a

PIM hello interval Hello Interval (sec)

PIM LAN delay (negotiated) n/a


2-253



PIM LAN delay (configured) Hello Delay

PIM override interval (negotiated) n/a

PIM override interval (configured) Override Interval (msec0

PIM neighbor tracking (negotiated) n/a

PIM neighbor tracking (configured) n/a

PIM generation ID n/a

PIM require generation ID n/a

PIM hello hold interval Hello Delay (sec)

PIM assert hold interval n/a

PIM triggered hello delay n/a

PIM J/P interval n/a

PIM J/P hold interval n/a

PIM state-refresh processing n/a

PIM state-refresh interval n/a

PIM state-refresh rate-limit n/a

PIM state-refresh TTL n/a

PIM graft retry interval n/a

Number of routers on network not using DR priority

n/a

Number of routers on network not using LAN delay

n/a

Number of routers on network not using neighbor tracking

n/a



2-254

Display Commandsdisplay pim join-prune

display pim join-prune

HP Switch# display pim join-prune mode sm VPN-Instance: public net Expiry Time: 51 sec Upstream nbr: 10.10.10.1 (Vlan-Interface10) 1 (*, G) join(s), 1 (S, G) join(s), 0 (S, G, rpt) prune(s)-------------------------------------------------------------Total (*, G) join(s): 1, (S, G) join(s): 1, (S, G, rpt) prune(s): 0|...+....1....+....2....+....3....+....4....+....5....+....6....+....7....+....8



display pim join-prune No equivalent ProVision software command


2-255

Display Commandsdisplay pim neighbor

display pim neighbor

Displays information about PIM neighbors.

Field Descriptions

VPN-Instance: public net: Public network

Total Number of Neighbors: Total number of PIM neighbors

Neighbor: IP address of the PIM neighbor

Interface: Interface connecting the PIM neighbor

Uptime: Length of time for which the PIM neighbor has been up, in hh:mm:ss

Expires/Expiry time: Remaining time of the PIM neighbor, in hh:mm:ss; “never” means that the PIM neighbor is always up and reachable.

Dr-Priority/DR Priority: Priority of the PIM neighbor

Mode: Mode of the PIM neighbor. The value “B” means the BIDIR-PIM mode. If nothing is displayed, it means the non-BIDIR-PIM mode.

Operating Notes



display pim neighbor show ip pim neighbor

HP Switch# display pim neighbor VPN-Instance: n/a Total Number of Neighbors = n/a Neighbor Interface Uptime Expires Dr-Priority Mode 10.1.1.2 Vlan100 02:50:49 00:01:31 n/a n/a 20.1.1.2 Vlan101 02:49:39 00:01:42 n/a n/a


2-256

Display Commandsdisplay pim neighbor


display pim neighbor Field Mappings.


HP Switch(config)# show ip pim neighbor

PIM Neighbors

IP Address VLAN Up Time (sec) Expire Time (sec) DR Priority --------------- ---- ---------------- ---------------- ---------- 10.10.10.2 100 348 90 1 10.20.10.1 200 410 97 1



Total Number of Neighbors n/a

Neighbor IP Address

Interface VLAN

Uptime UP Time (sec)

Expires/Expiry time Expire Time (sec)

Dr-Priority/DR Priority DR Priority

Mode n/a


2-257

Display Commandsdisplay pim neighbor <ip> verbose

display pim neighbor <ip> verbose

Displays information about PIM neighbors.

Field Descriptions

VPN-Instance: public net: Public network

Total Number of Neighbors: Total number of PIM neighbors

Neighbor: IP address of the PIM neighbor

Interface: Interface connecting the PIM neighbor

Uptime: Length of time for which the PIM neighbor has been up, in hh:mm:ss

Expires/Expiry time: Remaining time of the PIM neighbor, in hh:mm:ss; “never” means that the PIM neighbor is always up and reachable.

Dr-Priority/DR Priority: Priority of the PIM neighbor

Mode: Mode of the PIM neighbor. The value “B” means the BIDIR-PIM mode. If nothing is displayed, it means the non-BIDIR-PIM mode.

Generation ID: Generation ID of the PIM neighbor (a random value indicating a status change of the PIM neighbor)


display pim neighbor <ip> verbose show ip pim neighbor

HP Switch# display pim neighbor 11.110.0.20 verbose VPN-Instance: n/a Neighbor: 11.110.0.20 Interface: Vlan-interface100 Uptime: 00:00:10 Expiry time: 00:00:30 DR Priority: n/a Generation ID: n/a Holdtime: n/a LAN delay: n/a Override interval: n/a State refresh interval: n/a Neighbor tracking: n/a Bidirectional PIM: n/a


2-258


Holdtime: Holdtime of the PIM neighbor; “forever” means that the PIM neighbor is always up and reachable

LAN delay: Prune message delay

Override interval: Prune override interval

State refresh interval: Interval for sending state refresh messages/ Displayed only when the PIM neighbor works in PIM-DM mode and the state refresh capability is enabled.

Neighbor tracking: Neighbor tracking status (enabled/disabled)

Bidirectional PIM: BIDIR-PIM status (enabled/disabled)

Operating Notes



display pim neighbor Field Mappings.

HP Switch(config)# show ip pim neighbor

PIM Neighbors

IP Address VLAN Up Time (sec) Expire Time (sec) DR Priority --------------- ---- ---------------- ---------------- ---------- 10.10.10.2 100 348 90 1 10.20.10.1 200 410 97 1



Total Number of Neighbors n/a

Neighbor IP Address

Interface VLAN

Uptime UP Time (sec)


2-259



Expires/Expiry time Expire Time (sec)

Dr-Priority/DR Priority DR Priority

Mode n/a

Generation ID n/a

Holdtime n/a

LAN delay n/a

Override interval n/a

State refresh interval n/a

Neighbor tracking n/a

Bidirectional PIM n/a



2-260

Display Commandsdisplay pim routing-table

display pim routing-table

Displays the contents of the PIM multicast routing table, which includes SPT and RPF information.

HP Switch# display pim routing-tableVPN-Instance: public net Total 0 (*, G) entry; 1 (S, G) entry

(172.168.0.12, 227.0.0.1) Protocol: pim-sm, Flag: LOC UpTime: 02:54:43 Upstream interface: Vlan-interface20 Upstream neighbor: NULL RPF prime neighbor: NULL Downstream interface(s) information: Total number of downstreams: 1 1: Vlan-interface10 Protocol: pim-sm, UpTime: 02:54:43, Expires: 00:02:47



display pim routing-table No equivalent ProVision software command


2-261

Display Commandsdisplay pim rp-info

display pim rp-info

Displays information about pim RP.

HP Switch# display pim rp-info VPN-Instance: public net

PIM-SM BSR RP information:

Group/MaskLen: 224.0.0.0/4 RP: 10.10.10.11

Priority: n/a

HoldTime: 150 Uptime: n/a

Expires: 00:01:00



display pim rp-info No equivalent ProVision software command


2-262

Display Commandsdisplay poe device

display poe device

Displays the mapping between ID, module, and slot of the power sourcing equipment (PSE).

HP Switch# display poe device

PSE ID SlotNo SubSNo PortNum MaxPower(W) State Model A 1 n/a 24 370 off J9310A

Example of Related ProVision Software Command Output. HP Switch# show power-over-ethernet briefStatus and Counters - Port Power StatusSystem Power Status : No redundancyPoE Power Status : No redundancyAvailable: 300 W Used: 0 W Remaining: 300 WModule A PowerAvailable: 300 W Used: 5 W Remaining: 295 WPoE | Power Power Alloc Alloc Actual Configured Detection PowerPort | Enable Priority By Power Power Type Status Class------ + ------ -------- ----- ----- ------ ----------- ----------- -----A1 | Yes low usage 17 W 5.0 W Phone1 Delivering 1A2 | Yes low usage 17 W 0.0 W Searching 0A3 | Yes low usage 17 W 0.0 W Searching 0A4 | Yes low usage 17 W 0.0 W Searching 0A5 | Yes low usage 17 W 0.0 W Searching 0A6 | Yes low usage 17 W 0.0 W Searching 0

Operating Notes





display poe device show power-over-ethernet brief


2-263

Display Commandsdisplay poe interface

display poe interface

Displays the PoE status of a specific port on the switch.

HP Switch# display poe interface

Interface Enable Priority CurPower Operating IEEE Detection (W) Status Class Status

1 enable low 0.0 off 0 enabled 2 enable low 0.0 off 0 enabled 3 enable low 0.0 off 0 enabled 4 enable low 0.0 off 0 enabled 5 enable low 0.0 off 0 enabled 6 enable low 0.0 off 0 enabled 7 enable low 0.0 off 0 enabled 8 enable low 0.0 off 0 enabled 9 enable low 0.0 off 0 enabled 10 enable low 0.0 off 0 enabled 11 enable low 0.0 off 0 enabled 12 enable low 0.0 off 0 enabled 13 enable low 0.0 off 0 enabled 14 enable low 0.0 off 0 enabled 15 enable low 0.0 off 0 enabled 16 enable low 0.0 off 0 enabled 17 enable low 0.0 off 0 enabled 18 enable low 0.0 off 0 enabled 19 enable low 0.0 off 0 enabled 20 enable low 0.0 off 0 enabled 21 enable low 0.0 off 0 enabled 22 enable low 0.0 off 0 enabled 23 enable low 0.0 off 0 enabled 24 enable low 0.0 off 0 enabled

--- 24 port(s) on, 0.0 (W) consumed, 0.0 (W) remaining ---


display poe interface show power-over-ethernet brief


2-264

Display Commandsdisplay poe interface


Operating Notes





2-265

Display Commandsdisplay poe interface power

display poe interface power

Displays the PoE power information of the specified port on the switch. If you enter the command without an argument, the PoE power information about all PoE-capable ports on the switch is displayed.

HP Switch# display poe interface power

Interface CurPower PeakPower MaxPower PD Description (W) (W) (W)1 0.0 0.0 15.42 0.0 0.0 15.43 0.0 0.0 15.44 0.0 0.0 15.45 0.0 0.0 15.46 0.0 0.0 15.47 0.0 0.0 15.48 0.0 0.0 15.49 0.0 0.0 15.410 0.0 0.0 15.4 11 0.0 0.0 15.4 12 0.0 0.0 15.4 13 0.0 0.0 15.4 14 0.0 0.0 15.4 15 0.0 0.0 15.4 16 0.0 0.0 15.4 17 0.0 0.0 15.4 18 0.0 0.0 15.4 19 0.0 0.0 15.4 20 0.0 0.0 15.4 21 0.0 0.0 15.4 22 0.0 0.0 15.4 23 0.0 0.0 15.4 24 0.0 0.0 15.4

--- 0 port(s) on, 0.0 (W) consumed, 0.0 (W) remaining ---


display poe interface power show power-over-ethernet brief


2-266

Display Commandsdisplay poe interface power


Operating Notes





2-267

Display Commandsdisplay poe power-usage

display poe power-usage

Displays the power information of the PoE power and all PSEs.

HP Switch# display poe power-usagePoE Current Power : 0 WPoE Max Power : 37 WPoE Max Guaranteed Power : 0 WPoE Remaining Allocated Power : 0 WPoE Remaining Guaranteed Power : 0 WPoE Total Powered Port Number : 0 WDetailed power usage of PSE(s):PSE ID Max Current Peak Average Remaining Powered (W) (W) (W) (W) Guaranteed(W) PortNum7 37 0 0 0 37 010 37 0 0 0 37 0


Operating Notes





display poe power-usage show power-over-ethernet brief


2-268

Display Commandsdisplay poe-power alarm

display poe-power alarm

Displays detailed alarm information about the PoE PSUs.

HP Switch# display poe-power alarm PSU alarm detail, PSU number : 2 PSU 1 alarm : POWERED PSU 2 alarm : POWERED


HP Switch# show system power-supplyPower Supply Status: PS# | State | AC/DC + V | Wattage ----+-------------+-----------------+--------- 1 | Powered | AC 120VDL | 875 2 | Not Present | -- ---- | 0

1 / 2 supply bays delivering power. Total power: 875 W



display poe-power alarm show system power-supply


2-269

Display Commandsdisplay poe-power switch state

display poe-power switch state

Displays the number and current state of the AC power distribution switches of the PSUs.

HP Switch# display poe-power switch state Switch Number : 3 Switch 1 State : AC Switch Off Switch 2 State : AC Switch High Voltage Switch 3 State : AC Switch Off



display poe-power switch state No equivalent ProVision software command


2-270

Display Commandsdisplay port trunk

display port trunk

Displays information about the hybrid or trunk ports on the switch, including port names, default VLAN IDs (untagged vlan), and allowed VLAN IDs (tagged vlan).

HP Switch# display port trunk Interface PVID VLAN passing A1 1 1-2, 5-10 A2 10 1, 5



display port trunk No equivalent ProVision software command


2-271

Display Commandsdisplay power

display power

Displays information about the power supply of a device.

Field Descriptions

Power: Number of power supply bay.

State: State of power supply.


display power Field Mappings.



display power show system power-supply


Power PS#

State State

HP Switch# display power Power 1 State: Powered Power 2 State: Powered Power 3 State: Not Present Power 4 State: Not Present

HP Switch(config)# show system power-supply

Power Supply Status: PS# | State | AC/DC + V | Wattage ----+-------------+-----------------+--------- 1 | Powered | -- ---- | 0

1 / 1 supply bays delivering power.


2-272

Display Commandsdisplay protocol-vlan

display protocol-vlan

Displays the protocols and protocol indexes configured on the specified VLANs.

HP Switch# display protocol-vlan VLAN ID:10 Protocol Index Protocol Type============================================= 1 IPv4 2 IPX 3 ARP



display protocol-vlan No equivalent ProVision software command


2-273

Display Commandsdisplay protocol-vlan interface

display protocol-vlan interface

Displays information about protocol-based VLANs on all ports.

HP Switch# display protocol-vlan interface all Interface: A1 VLAN ID Protocol Index Protocol Type ====================================================== 2 2 IPX Interface: F24 VLAN ID Protocol Index Protocol Type ====================================================== 4 5 Appletalk 4 1 IPv4 4 6 SNA



display protocol-vlan interface No equivalent ProVision software command


2-274

Display Commandsdisplay public-key local rsa public

display public-key local rsa public

Displays public key information of the local key pairs. This command is available only in manager mode.

HP Switch# display public-key local rsa public=====================================================Time of Key pair created: 16:53:41 2012/05/08Key name: HOST_KEYKey type: RSA Encryption Key=====================================================Key code:30819F300D06092A864886F70D010101050003818D0030818902818100C371A8F1C7BAC3B7BD9003B9B0F8F2D77980D160B998227F75F395CAD5663EEF16F9DC71CBD22149439F2BAC388B0F197141463129E6A5B83692D914A7DA8F34F0B8CB2C71C9DD7301D7231993AD357650731D4DC40B1DE825CB5B6FE8ED963AD7DFCF9AEF4A5E76DDBBA1ADD8AB533A4335963CE88825F7FFB1CB1F6DA5505D0203010001

=====================================================Time of Key pair created: n/aKey name: SERVER_KEYKey type: RSA Encryption Key=====================================================Key code:n/a


HP Switch# show crypto host-public-keySSH host public key:ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQDNwBMXZ9vYG+YxtV+KQeQQ+R8RKx47lxs14jPImBoVqUmK1iyK3WGhv0Fsks9ZtATjidybwPjmfd2Lup1INUjemquL2C0YRXo4MULfrqioWTco4mlFliftypj5gLvYeYFT/9CpoxMF4YrTUyjc90UfIf3et3fahaZ4KgLQjnXV1b8AWWsDZRv7niq8A1emqgts3HuAk59L


display public-key local rsa public show crypto host-public-keyshow ip host-public-key


2-275

Display Commandsdisplay public-key local rsa public

vFYsMkvLV2a7qoks1auqW8otRHgv/QsWtxfuoYUvVnXDiZFKeent34+sQnIvy1wJAmukCmM3zp434eTeh87/2Oer612mlAwRq5qPFtTAZlsf8LGipjKftW6dq8uq9tYtTtQWO09Mi65L

Operating Notes




2-276

Display Commandsdisplay public-key peer

display public-key peer

Displays brief information about all the public keys of remote hosts.

HP Switch# display public-key peer

Key Name : "rsa-key-20120206" Key Type : RSA Key Module : 1024 Key Code : raky2100"shraAABNa1cEAAJAABm2ufBHv80BmMgle//m9Hq8N4B1c+N1i3eUfyLN4bZBi2cIEXNU/cXDUo3FINB8k+xb2fhNfIQ8rT0Q0Y/a+XR=

Field Descriptions:

Key name: Key name, which can be one of the following values:

• HOST_KEY: Host public key

• SERVER_KEY: Server public key. This value is available only for RSA key pairs.

Key type: Key type, which can be one of the following values:

• RSA Encryption Key: RSA key pair

• DSA Encryption Key: DSA key pair

Key code: Key data


HP Switch# show crypto client-public-key

Operator keys:

0,[email protected] ssh-rsa AAAAB3NzaC1yc2EAAAABIwAAAQEAsGffNl6CFBtxgEPExkZwbauXCiBLnzztD5qA2IafkQzOy22gMDAl6rinTXvDcdP6P+RDGX+76p0E4IabwnmdpdSX+jCCV7PDjYumrAomXF9uZ+6Mg6xkAURoXdisSwTiY9jeNyfCLrcLGy+4i9B2YEz3IO0qH7D8ciwfhTbkEnOCLIFGSYzGUGsbXbHRTd6prOogAIJg1lnXjSXLgHikdAtLFNNDwTXnxvX0SE02zeVehAb8XNHwZc6vy5FneKGjH9waq/TEEqVJPwAJ6A5diuUvaFlAQGj53y4QqdaMORcfRXMfGtOCsEx/jX5pmJAJ7MsB/NX1AHSowgRUaIR0qw==



display public-key peer show ip client-public-key


2-277

Display Commandsdisplay radius scheme

display radius scheme

Displays the configuration information of RADIUS schemes.


display radius scheme show radiusshow radius host <host>show accounting


2-278


HP Switch# display radius scheme

------------------------------------------------------------------SchemeName : n/a Index : n/a Type : n/a Primary Auth Server : IP : 1.2.3.4 Port : 1812 State : n/a Encryption Key : samplee123 VPN instance : n/a Primary Acct Server : IP : 1.2.3.4 Port : 1813 State : n/a Encryption Key : samplee123 VPN instance : n/a Second Auth Server IP : 2.3.4.5 Port : 1812 State : n/a Encryption Key : ghefijklm VPN instance : n/a IP : 4.5.6.7 Port : 1812 State : n/a Encryption Key : abcdegh VPN instance : n/a IP : 4.5.6.8 Port : 1812 State : n/a Encryption Key : abcdegh VPN instance : n/a Second Acct Server IP : 2.3.4.5 Port : 1813 State : n/a Encryption Key : ghefijklm VPN instance : n/a IP : 4.5.6.7 Port : 1813 State : n/a Encryption Key : abcdegh VPN instance : n/a IP : 4.5.6.8 Port : 1813 State : n/a Encryption Key : abcdegh VPN instance : n/a Auth Server Encryption Key : Acct Server Encryption Key : VPN instance : n/a Accounting-On packet disable, send times : n/a , interval : n/a Interval for timeout(second) : 5 Retransmission times for timeout : 3 Interval for realtime accounting(minute) : 0 Retransmission times of realtime-accounting packet : 3 Retransmission times of stop-accounting packet : 3 Quiet-interval(min) : 0 Username format : n/a Data flow unit : n/a Packet unit : n/a NAS-IP address : n/a Attribute 25 : n/a ------------------------------------------------------------------Total 1 RADIUS scheme(s).


2-279


Field Descriptions

SchemeName: Name of the RADIUS scheme.

Index: Index number of the RADIUS scheme.

Type: Type of the RADIUS server, extended or standard.

Primary Auth Server: Information about the primary authentication server.

Primary Acct Server: Information about the primary accounting server.

Second Auth Server: Information about the secondary authentication server.

Second Acct Server: Information about the secondary accounting server.

IP: Ip address of the server.

Port: Service port of the server. If no port configuration is performed, the default port number is displayed.

State: Status of the server, active or blocked.

Encryption Key: Shared key for authenticating authentication or accounting packets, in cipher text or plain text. If no shared key is configured, the value of this field is N/A. This shared key is used only when no specific shared key is specified for the RADIUS server.

VPN instance: MPLS L3VPN that the server belongs to. If no VPN instance is specified for the server, the value of this field is N/A.

Auth Server Encryption Key: Shared key for authenticating authentication pack-ets, in cipher text or plain text.

Acct Server Encryption Key: Shared key for authenticating accounting packets, in cipher text or plain text.

Accounting-On packet disable: The accounting-on feature is disabled.

send times: Retransmission times of accounting-on packets.

interval: Interval at which the device retransmits accounting-on packets.

Interval for timeout (second): RADIUS server response timeout period, in sec-onds.

Retransmission times for timeout: Maximum number of attempts for transmitting a RADIUS packet to a single RADIUS server.


2-280


Interval for realtime accounting(minute): Interval for realtime accounting, in minutes.

Retransmission times of realtime-accounting packet: Maximum number of accounting attempts

Retransmission times of stop-accounting packet: Maximum number of stop-accounting attempts

Quiet-interval(min): Quiet interval for the primary server.

Username format: Format of the usernames to be sent to the RADIUS server.

Data flow unit: Unit for data flows sent to the RADIUS server.

Packet unit: Unit for packets sent to the RADIUS server.

NAS-IP address: Source IP address for RADIUS packets to be sent.

Attribute 25: Interprets RADIUS attribute 25 as the CAR parameters.

Operating Notes

For more information on switch RADIUS operation, see the “RADIUS Authen-tication, Authorization, and Accounting” chapter in the latest Access Security



HP Switch# show radius

Status and Counters - General RADIUS Information

Deadtime(min) : 5 Timeout(secs) : 10 Retransmit Attempts : 2 Global Encryption Key : myg10balkey Dynamic Authorization UDP Port : 3799 Source IP Selection : Outgoing Interface

Auth Acct DM/ Time Server IP Addr Port Port CoA Window Encryption Key OOBM --------------- ---- ---- --- ------ -------------------------------- ----- 192.33.12.65 1812 1813 No 300 my65key No


2-281


display radius scheme Field Mappings.

HP Switch(config)# show radius host 192.33.12.65 Status and Counters - RADIUS Server Information Server IP Addr : 192.33.12.65 Authentication UDP Port : 1812 Accounting UDP Port : 1813 Round Trip Time : 2 Round Trip Time : 7 Pending Requests : 0 Pending Requests : 0 Retransmissions : 0 Retransmissions : 0 Timeouts : 0 Timeouts : 0 Malformed Responses : 0 Malformed Responses : 0 Bad Authenticators : 0 Bad Authenticators : 0 Unknown Types : 0 Unknown Types : 0 Packets Dropped : 0 Packets Dropped : 0 Access Requests : 2 Accounting Requests : 2 Access Challenges : 0 Accounting Responses : 2 Access Accepts : 0 Access Rejects : 0


SchemeName n/a

Index n/a

Type n/a

Primary Auth Server Server IP Address

Primary Acct Server Server IP Address

Second Auth Server n/a

HP Switch(config)# show accounting

Status and Counters - Accounting Information

Interval(min) : 5 Suppress Empty User : No Sessions Identification : Common

Type | Method Mode Server Group -------- + ------ -------------- ------------ Network | None Exec | Radius Start-Stop System | Radius Stop-Only Commands | Radius Interim-Update


2-282



Second Acct Server n/a

IP Server IP Address

Port Auth Port or Acct Port

State n/a

Encryption Key Encryption Key

VPN instance n/a

Auth Server Encryption Key n/a

Acct Server Encryption Key n/a

Accounting-On packet disable, send times

n/a

Interval for timeout (sec) Timeout (secs)

Retransmission times for timeout

n/a

Interval for realtime accounting (minute)

Interval(min)

Retransmission times of realtime-accounting packet

n/a

Retransmission times of stop-accounting packet

n/a

Quiet-interval(min) Deadtime (min)

Username format n/a

Data flow unit n/a

Packet unit n/a

NAS-IP address n/a

Attribute 25 n/a

n/a Retransmit Attempts

n/a Dynamic Authorization UDP Port

n/a Source IP Selection



2-283

Display Commandsdisplay rip

display rip

Displays RIP configuration information. The command provides information regarding the version, preference, cost, summary, maximum number of bal-anced paths, configured peers, number of route changes and number of replies to queries in a RIP route.

HP Switch# display rip Public VPN-instance name : n/a

RIP process : n/a RIP version : 1 Preference : 120 checkzero : n/a Default-cost : 1 Summary : Enabled Hostroutes : n/a Maximum number of balanced paths : 4 Update time : n/a Timeout time : n/a Suppress time : n/a Garbage-collect time : n/a Update output delay : n/a Output count : n/a TRIP retransmit time : n/a TRIP response packets retransmit count : n/a Silent interfaces : n/a Default routes : Disabled Verify-source : Enabled Networks : n/a Configured peers : None Triggered updates sent : 0 Number of route changes : 0 Number of replies to queries : 0



display rip No equivalent ProVision software command


2-284

Display Commandsdisplay rip interface

display rip interface

Displays RIP interface information of the RIP process. If no interface is specified, information about all RIP interfaces of the RIP process is displayed.

HP Switch# display rip 1 interface

Interface-name: Vlan-interface2 Address/Mask:2.2.2.2/24 Version:RIPv2 MetricIn:1 MetricIn route policy:n/a MetricOut:0 MetricOut route policy:n/a Split-horizon/Poison-reverse:on/on Input/Output:on/on Default route:on Current packets number/Maximum packets number:n/a


Interface-name: Vlan-interface4 Address/Mask:192.168.4.55/16 Version:RIPv1 or RIPv2 MetricIn:1 MetricIn route policy:n/a MetricOut:0 MetricOut route policy:n/a Split-horizon/Poison-reverse:on/off Input/Output:on/on Default route:on Current packets number/Maximum packets number:n/a

HP Switch# display rip 1 interface vlan-interface 2




display rip interface No equivalent ProVision software command


2-285

Display Commandsdisplay rip process-id ip-address mask/mask-length

display rip process-id ip-address mask/mask-length

Displays routes learnt by RIP. The command provides information regarding the peer address, vlan-interface (to which the peer is connected), route destination, route destination mask, route NextHop, route cost, route flags, route secs for all the routes that RIP has learnt.

HP Switch # display rip 1 route 20.0.0.0 8

Route Flags: R - RIP, T - TRIP P - Permanent, A - Aging, S - Suppressed, G - Garbage-collect------------------------------------------------------------- Peer 10.1.1.1 on Vlan-interface10

Destination/Mask Nexthop Cost Tag Flags Sec 20.0.0.0/8 10.1.1.1 1 0 RA 5



display rip process-id ip-address mask/mask-length



2-286

Display Commandsdisplay rip process-id route

display rip process-id route

HP Switch# display rip 1 route

Route Flags: R - RIP, T - TRIP

P - Permanent, A - Aging, S - Suppressed, G - Garbage-collect ------------------------------------------------------------- Peer 10.1.1.1 on Vlan-interface10 Destination/Mask Nexthop Cost Tag Flags Sec 5.0.0.0/8 10.1.1.1 2 0 RA 5 6.0.0.0/8 10.1.1.1 1 0 RA 5 20.0.0.0/8 10.1.1.1 1 0 RA 5



display rip process-id route No equivalent ProVision software command


2-287

Display Commandsdisplay rip process-id route peer ip-address

display rip process-id route peer ip-address

HP Switch# display rip 1 route peer 10.1.1.1

Route Flags: R - RIP, T - TRIP

P - Permanent, A - Aging, S - Suppressed, G - Garbage-collect ------------------------------------------------------------- Peer 10.1.1.1 on Vlan-interface10

Destination/Mask Nexthop Cost Tag Flags Sec 5.0.0.0/8 10.1.1.1 2 0 RA 5 6.0.0.0/8 10.1.1.1 1 0 RA 5 20.0.0.0/8 10.1.1.1 1 0 RA 5



display rip process-id route peer ip-address No equivalent ProVision software command


2-288

Display Commandsdisplay rmon statistics

display rmon statistics

Displays rmon statistics for the remote monitoring statistics information.HP Switch# display rmon statistics A1EtherStatsEntry 1 owned by monitor: is 1 Interface:A1 etherStatsOctets : 3724 , etherStatsPkts : 24 etherStatsBroadcastPkts : 4 , etherStatsMulticastPkts : 15 etherStatsUndersizePkts : 0 , etherStatsOversizePkts : 0 etherStatsFragments : 0 , etherStatsJabbers : 0 etherStatsCRCAlignErrors : 0 , etherStatsCollisions : 0 etherStatsDropEvents(insufficient resources) : 0 Packets received according to length: 64 : 12 , 65-127 : 0 , 128-255 : 8 256-511 : 4 , 512-1023 : 0 , 1024-1518 : 0

Operating Notes

For more information, refer to the latest Command Line Interface Reference




display rmon statistics show rmon statistics


2-289

Display Commandsdisplay route-policy

display route-policy

Displays FIPS state. By default, the FIPS mode is disabled.

HP Switch# display route-policyRoute-Policy : qwer permit :10 if-match community abcd permit :11 if-match interface vlan 2 if-match ip-nexthop Prefix test if-match ipv6-route-source abcd if-match ipv6-address test if-match local-preference 32 if-match metric 44 if-match routetype external 2 if-match sourceprotocol static if-match tag 33 if-match community none if-match ip-nexthop 1.2.3.4 if-match ipv6-nexthop 2001:db8:85a3::8a2e:370:7334 if-match as-path test apply origin egpRoute-Policy : test permit :12 if-match community test deny :20 apply metric 3 apply tag 33 apply asPathPrepend apply weight 44


HP Switch# show route-map Map3Routemap information

route-map "Map3" permit seq 10 match interface vlan 11 12 13 match metric 25 exitroute-map "Map3" permit seq 20


display route-policy show route-map


2-290

Display Commandsdisplay route-policy

match interface vlan 21 22 23 match metric 25exit




2-291

Display Commandsdisplay saved-configuration

display saved-configuration

Displays contents of the configuration file saved for the next startup of the switch.

HP Switch# display saved-configuration ; J8697A Configuration Editor; Created on release #K.15.09.0000x; Ver #03:01.1f.ef:f2hostname "HP-5406zl"module 1 type J9536Amodule 6 type J9534Asnmp-server community "public" Unrestrictedvlan 1 name "DEFAULT_VLAN" untagged A1-A22,F1-F24 ip address dhcp-bootp exit


HP Switch# show configStartup configuration:; J8697A Configuration Editor; Created on release #K.14.01hostname "HP Switch"module 1 type J8705Asnmp-server community "public" Unrestrictedvlan 1 name "DEFAULT_VLAN" untagged A1-A24 ip address dhcp-bootp exitinterface A1 rate-limit all out kbps 200 exitinterface A2 rate-limit all out kbps 200 exitinterface A3 rate-limit all out kbps 200 exitinterface A4 rate-limit all out kbps 200


display saved-configuration show config


2-292

Display Commandsdisplay saved-configuration

exitinterface A5 rate-limit all in percent 200 exitinterface A6 rate-limit icmp percent 60 rate-limit mcast in percent 60 exit




2-293

Display Commandsdisplay saved-configuration by-linenum

display saved-configuration by-linenum

Displays the saved configuration of the switch with the line number. This command adds the line number to the output of display saved-configuration. This command is available only in manager mode.HP Switch# display saved-configuration by-linenum; J8692A Configuration Editor; Created on release #K.15.09.0000x; Ver #03:01.1f.ef:f2 1: hostname "HP-E3500yl-24G" 2: module 1 type J86xxA 3: snmp-server community "public" Unrestricted 4: vlan 1 5: name "DEFAULT_VLAN" 6: untagged 1-24 7: ip address dhcp-bootp 8: exit


HP Switch# show configStartup configuration:; J8697A Configuration Editor; Created on release #K.14.01hostname "HP Switch"module 1 type J8705Asnmp-server community "public" Unrestrictedvlan 1name "DEFAULT_VLAN"untagged A1-A24ip address dhcp-bootpexitinterface A1rate-limit all out kbps 200exitinterface A2rate-limit all out kbps 200exitinterface A3rate-limit all out kbps 200exitinterface A4rate-limit all out kbps 200exitinterface A5rate-limit all in percent 200


display saved-configuration by-linenum show config


2-294

Display Commandsdisplay saved-configuration by-linenum

exitinterface A6rate-limit icmp percent 60rate-limit mcast in percent 60exit

Operating Notes





2-295

Display Commandsdisplay schedule reboot

display schedule reboot

Displays the user-configured switch reboot (reload) time. For example, if the current date and time is March 21, 2012 at 1:05 PM (13:05), and the switch is configured to reboot (reload) at 5:00 PM (17:00) on the same date, then you would see the following output when executing this command:

HP Switch(config)# display schedule reboot System will reboot at 17:00 03/21/2012 (in 3 hours and 55 minutes).

Operating Notes

To configure a reboot time on the switch, use the following command:

[no] reload [ after | at ]

For more on using the reload command, refer to the “Switch Memory and Configuration” chapter in the latest Basic Operation Guide for your switch.


HP Switch(config)# show reload at

Reload scheduled for 17:00:52 02/21/2012 (in 0 days, 3 hours, 55 minutes)



display schedule reboot show reload < after | at >


2-296

Display Commandsdisplay sflow display sflow slot <slot-number>

display sflow display sflow slot <slot-number>

Displays the sflowglobal, collector and port information.

HP Switch# display sflowsFlow Version: 1.3;HP;K.15.10.0000xsFlow Global Information:Agent IP:120.93.219.32(Auto)Collector Information:ID IP Port Aging Size Description1 1.2.3.4 1 2147483512 1400 n/a2 1.2.3.5 2 2147483525 1400 n/a3 1.2.3.6 3 2147483547 1400 n/asFlow Port Information:Interface CID Interval(s) FID MaxHLen Rate Mode StatusA4 1 0 1 128 51 Random InactiveA5 2 0 2 128 52 Random InactiveA6 3 0 3 128 53 Random InactiveC1 2 0 2 128 88 Random ActiveF10 1 0 1 128 77 Random Inactive

HP Switch# display sflow slot AsFlow Version: 1.3;HP;K.15.10.0000xsFlow Global Information:Agent IP:120.93.219.32(Auto)Collector Information:ID IP Port Aging Size Description1 1.2.3.4 1 2147483512 1400 n/a2 1.2.3.5 2 2147483525 1400 n/a3 1.2.3.6 3 2147483547 1400 n/asFlow Port Information:Interface CID Interval(s) FID MaxHLen Rate Mode StatusA4 1 0 1 128 51 Random InactiveA5 2 0 2 128 52 Random InactiveA6 3 0 3 128 53 Random Inactive


display sflowdisplay sflow slot <slot-number>

sh sflow agentsh sflow <receiver table number> sampling-polling


2-297

Display Commandsdisplay sflow display sflow slot <slot-number>


HP Switch# sh sflow agent Version : 1.3;HP;K.15.10.0000x Agent Address : 120.93.219.32 Source IP Selection : Outgoing Interface

HP Switch# sh sflow 1 sampling-polling

Port | Sampling Dropped | Polling | Enabled Rate Header Samples | Enabled Interval----- + ------- -------- ------ ---------- + ------- --------A1 --- --- --- --- Yes(1) 21A4 Yes(1) 51 128 0 --- ---F10 Yes(1) 77 128 0 --- ---



2-298

Display Commandsdisplay snmp-agent community

display snmp-agent community

Displays community information for SNMPv1 or SNMPv2. This command is available only in manager mode.HP Switch# display snmp-agent community Community name: public Group name: n/a Storage-type: volatile


HP Switch# show snmpv3 community

snmpCommunityTable [rfc2576]

Index Name Community Name Security Name---------- --------------- ------------------------1 public CommunityManagerReadWrite2 Operator CommunityOperatorReadOnly3 Manager CommunityManagerReadWrite30 Operator CommunityManagerReadWrite

Operating Notes





display snmp-agent community show snmpv3 community


2-299

Display Commandsdisplay snmp-agent group

display snmp-agent group

Displays information for the SNMPv3 agent group, including group name, security model, MIB view, and storage type. Absence of the group-name parameter indicates that information for all groups is displayed.HP Switch# display snmp-agent group Group name: ComManagerR Security model: v1 noAuthnoPriv Readview: ManagerReadView Writeview: DiscoverView Notifyview: ManagerReadView Storage-type: ReadOnly Group name: ComManagerR Security model: v2 noAuthnoPriv Readview: ManagerReadView Writeview: DiscoverView Notifyview: ManagerReadView Storage-type: ReadOnly Group name: ManagerAuth Security model: v3 AuthnoPriv Readview: ManagerReadView Writeview: ManagerWriteView Notifyview: ManagerReadView Storage-type: ReadOnly Group name: ManagerPriv Security model: v3 AuthPriv Readview: ManagerReadView Writeview: ManagerWriteView Notifyview: ManagerReadView Storage-type: ReadOnly Group name: ComManagerRW Security model: v1 noAuthnoPriv Readview: ManagerReadView Writeview: ManagerWriteView Notifyview: ManagerReadView Storage-type: ReadOnly Group name: ComManagerRW Security model: v2 noAuthnoPriv Readview: ManagerReadView Writeview: ManagerWriteView Notifyview: ManagerReadView Storage-type: ReadOnly Group name: ComOperatorR


display snmp-agent group show snmpv3 group


2-300


Security model: v1 noAuthnoPriv Readview: OperatorReadView Writeview: DiscoverView Notifyview: OperatorReadView Storage-type: ReadOnly Group name: ComOperatorR Security model: v2 noAuthnoPriv Readview: OperatorReadView Writeview: DiscoverView Notifyview: OperatorReadView Storage-type: ReadOnly Group name: OperatorAuth Security model: v3 AuthnoPriv Readview: OperatorReadView Writeview: DiscoverView Notifyview: OperatorReadView Storage-type: ReadOnly Group name: ComOperatorRW Security model: v1 noAuthnoPriv Readview: OperatorReadView Writeview: OperatorReadView Notifyview: OperatorReadView Storage-type: ReadOnly Group name: ComOperatorRW Security model: v2 noAuthnoPriv Readview: OperatorReadView Writeview: OperatorReadView Notifyview: OperatorReadView Storage-type: ReadOnly Group name: OperatorNoAuth Security model: v3 noAuthnoPriv Readview: OperatorReadView Writeview: DiscoverView Notifyview: OperatorReadView Storage-type: ReadOnly


2-301



HP Switch# show snmpv3 group

Status and Counters - SNHP v3 Global Configuration Information

Security Name Security Model Group Name------------------------ -------------- -----------------CommunityManagerReadOnly ver1 ComManagerRCommunityManagerReadWrite ver1 ComManagerRWCommunityOperatorReadOnly ver1 ComOperatorRWCommunityOperatorReadWrite ver1 ComOperatorRWCommunityManagerReadOnly ver2c ComManagerRCommunityManagerReadWrite ver2c ComManagerRWCommunityOperatorReadOnly ver2c ComOperatorRWCommunityOperatorReadWrite ver2c ComOperatorRWNetworkMgr ver3 ManagerPrivNetworkAdmin ver3 OperatorNoAuth

Operating Notes





2-302

Display Commandsdisplay snmp-agent local-engineid

display snmp-agent local-engineid

Displays the SNMP agent local engine ID.

HP Switch# display snmp-agent local-engineid SNMP local EngineID: 0000000b0000001871c42f00

Field Descriptions

SNMP local EngineID: Identifies an SNMP entity uniquely within an SNMP domain.

Operating Notes

There is no specific user configuration command for SNMP agent local engine ID.

For more on switch SNMP operation, refer to the “Configuring for Network Management Applications” chapter in the latest Management and Configu-

ration Guide for your switch.


HP Switch# HP Switch# show snmpv3 engineid

Status and Counters - SNMP v3 EngineId Information

EngineId: 00:00:00:0b:00:00:00:18:71:c4:2f:00

snmp-agent local-engineid Field Mappings.



display snmp-agent local-engineid show snmpv3 engineid


SNMP local EngineID EngineID


2-303

Display Commandsdisplay snmp-agent mib-view

display snmp-agent mib-view

Displays the View name, MIB Subtree, Subtree mask, Storage-type, View Type and View status. This command is available only in manager mode.HP Switch# display snmp-agent mib-view

View name: DiscoverView MIB Subtree: 1.3.6.1.6.3.15.1.2.2.1.7 Subtree mask: Storage-type: readOnly View Type: included View status: notInService Storage-type: readOnly

View name: DiscoverView MIB Subtree: 1.3.6.1.6.3.15.1.2.2.1.10 Subtree mask: Storage-type: readOnly View Type: included View status: notInService


HP Switch# show snmpv3 group

Status and Counters - SNHP v3 Global Configuration Information

Security Name Security Model Group Name------------------------ -------------- -----------------CommunityManagerReadOnly ver1 ComManagerRCommunityManagerReadWrite ver1 ComManagerRWCommunityOperatorReadOnly ver1 ComOperatorRWCommunityOperatorReadWrite ver1 ComOperatorRWCommunityManagerReadOnly ver2c ComManagerRCommunityManagerReadWrite ver2c ComManagerRWCommunityOperatorReadOnly ver2c ComOperatorRWCommunityOperatorReadWrite ver2c ComOperatorRWNetworkMgr ver3 ManagerPrivNetworkAdmin ver3 OperatorNoAuth

Operating Notes





display snmp-agent mib-view show snmpv3 group


2-304

Display Commandsdisplay snmp-agent statistics

display snmp-agent statistics

Displays SNMP statistics, identifies SNMP PDUs, and provides information regarding the number of PDUs in request, reply, get, set, errors and MIB retrieval and altered state.HP Switch# display snmp-agent statistics 0 Messages delivered to the SNMP entity 0 Messages which were for an unsupported version 0 Messages which used a SNMP community name not known 0 Messages which represented an illegal operation for the community supplied 0 ASN.1 or BER errors in the process of decoding 0 Messages passed from the SNMP entity 0 SNMP PDUs which had badValue error-status 0 SNMP PDUs which had genErr error-status 0 SNMP PDUs which had noSuchName error-status 0 SNMP PDUs which had tooBig error-status (Maximum packet size 1500) 10 MIB objects retrieved successfully 1 MIB objects altered successfully 0 GetRequest-PDU accepted and processed 0 GetNextRequest-PDU accepted and processed 0 GetBulkRequest-PDU accepted and processed 0 GetResponse-PDU accepted and processed 0 SetRequest-PDU accepted and processed 0 Trap PDUs accepted and processed 0 Alternate Response Class PDUs dropped silently 0 Forwarded Confirmed Class PDUs dropped silently



display snmp-agent statistics No equivalent ProVision software command


2-305

Display Commandsdisplay snmp-agent sys-info

display snmp-agent sys-info

Displays current SNMP system information.HP Switch# display snmp-agent sys-infoThe contact person for this managed node: admin The physical location of this node: HP SNMP version running in the system: SNMPv1 SNMPv2c SNMPv3


HP Switch# show system informationStatus and Counters - General System InformationSystem Name : HP SwitchSystem Contact :System Location :MAC Age Time (sec) : 300Time Zone : 0Daylight Time Rule : None

Operating Notes




display snmp-agent sys-info show system information


2-306

Display Commandsdisplay snmp-agent trap-list

display snmp-agent trap-list

Displays modules that can generate traps and whether or not their trap function is enabled. This command is available only in manager mode.HP Switch# display snmp-agent trap-list snmp Authentication trap extended password change trap enable login failures trap enable port security trap enable authorization server contact trap enable dhcp-snooping trap enable dynamic arp protection trap enable dynamic ip lockdown trap enable startup config change trap disable running config change trap disable mac address table changes trap disable mac address count trap disable

Enable traps: 8; Disable traps: 4


HP Switch# show snmp-server traps

Trap Receivers

Link-Change Traps Enabled on Ports [All] : A1-A24

Traps Category Current Status-------------------------- ---------------SNMP Authentication : ExtendedPassword change : EnabledLogin failures : EnabledPort-Security : EnabledAuthorization Server Contact : EnabledDHCP Snooping : EnabledDynamic ARP Protection : EnabledDynamic IP Lockdown : Enabled

Address Community Events Sent Notify Type Retry Timeout----------------- ------- ----------- ----------- ----- ------- 15.255.5.225 public All trap 3 152001:0db8:0000:0001:0000:0000:0000:0121 user_1 All trap 3 15

Excluded MIBs


display snmp-agent trap-list show snmp-server traps


2-307

Display Commandsdisplay snmp-agent trap-list

Operating Notes





2-308

Display Commandsdisplay snmp-agent usm-user

display snmp-agent usm-user

Displays the snmp users configured in the system. This command is available only in manager mode.HP Switch# display snmp-agent usm-user

User name: user Group name: ComOperatorR Engine ID: 0000000B00000019BBBACD00 Storage-type: nonVolatile UserStatus: active

User name: initial Group name: ManagerPriv Engine ID: 0000000B00000019BBBACD00 Storage-type: nonVolatile UserStatus: active


HP Switch# show snmpv3 userStatus and Counters - SNMP v3 Global Configuration InformationUser Name Auth. Protocol Privacy Protocol------------ -------------- ----------------initial MD5 CFB AES-128NetworkAdmin MD5 CBC-DES

Operating Notes





display snmp-agent usm-user show snmpv3 user


2-309

Display Commandsdisplay ssh client source

display ssh client source

Displays the source IP address or source interface currently set for the SSH client. If neither source IP address nor source interface is specified for the SSH client, the system will prompt you to specify the source information.

HP Switch# display ssh client source

Neither source IP address nor source interface was specified for the STelnet client.



display ssh client source No equivalent ProVision software command


2-310

Display Commandsdisplay ssh server session

display ssh server session

Displays SSH server session information. This command is available only in manager mode.HP Switch# display ssh server session

Conn Ver Encry State Retry SerType UsernameA1 2.0 AES Established n/a Stelnet manager


HP Switch# show ip sshSSH Enabled : Yes Secure Copy Enabled : NoTCP Port Number : 22 Timeout (sec) : 120Host Key Type : RSA Host Key Size : 2048

Ciphers : aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc, [email protected],aes128-ctr,aes192-ctr,aes256-ctr

MACs : hmac-md5,hmac-sha1,hmac-sha1-96,hmac-md5-96

Ses Type | Source IP Port--- -------- + -------------- -------1 console |2 telnet |3 ssh | 15.30.252.195 15314 inactive |5 inactive |6 inactive |

Operating Notes




display ssh server session show ip ssh


2-311

Display Commandsdisplay ssh server-info

display ssh server-info

Displays mappings between SSH servers and their host public keys saved on the client.HP Switch# display ssh server-infoServer Name(IP) Server public key name---------------- -----------------------120.85.212.127 n/a



display ssh server-info No equivalent ProVision software command


2-312

Display Commandsdisplay ssh server status

display ssh server status

Displays the SSH server status information or session information.

HP Switch# display ssh server status

SSH server : enabled SSH version : 2 SSH authentication-timeout : 120 second(s) SSH server key generating interval : n/a SSH authentication retries : 3 time(s) SFTP server : disabled SFTP server Idle-Timeout : 0 minutes(s)

Field Descriptions:

SSH server: Whether the SSH server function is enabled

SSH version: SSH protocol version. When the SSH supports SSH1, the protocol version is 1.99. Otherwise, the protocol version is 2.0.

SSH authentication-timeout: Authentication timeout period

SSH server key generating interval: SSH server key pair update interval

SSH authentication retries: Maximum number of SSH authentication attempts

SFTP server: Whether the SFTP server function is enabled

SFTP server Idle-Timeout: SFTP connection idle timeout period


HP Switch(config)# show ip ssh

SSH Enabled : Yes Secure Copy Enabled : No TCP Port Number : 22 Timeout (sec) : 120 Host Key Type : RSA Host Key Size : 2048

Ciphers : aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc,

[email protected],aes128-ctr,aes192-ctr,aes256-ctr


display ssh server status show ip ssh


2-314

Display Commandsdisplay ssl client-policy

display ssl client-policy

Displays information about all SSL client policies. This command is available only in manager mode.HP Switch# display ssl client-policySSL Client Policy: n/a SSL Version: TLS 1.0 PKI Domain: n/a Prefer Ciphersuite: aes256-ctr aes256-cbc [email protected] aes192-ctr aes192-cbc aes128-ctr aes128-cbc 3des-cbc hmac-sha1-96 hmac-md5 hmac-sha1 hmac-md5-96 aes192-ctr aes192-cbc aes128-ctr aes128-cbc 3des-cbc Server-verify: n/aTotal 1 SSL client policy(s).





Ses Type | Source IP Port--- -------- + -------------- -------1 console |2 telnet |3 ssh | 15.30.252.195 15314 inactive |5 inactive |


display ssl client-policy show ip ssh


2-315

Display Commandsdisplay ssl client-policy

6 inactive |

Operating Notes




2-316

Display Commandsdisplay ssl server-policy

display ssl server-policy

Displays information about all SSL client policies. This command is available only in manager mode.HP Switch# display ssl server-policySSL Server Policy: n/a PKI Domain: n/a Ciphersuite: aes256-ctr aes256-cbc [email protected] aes192-ctr aes192-cbc aes128-ctr aes128-cbc 3des-cbc hmac-sha1-96 hmac-md5 hmac-sha1 hmac-md5-96 aes192-ctr aes192-cbc aes128-ctr aes128-cbc 3des-cbc Handshake Timeout: 120 Close-mode: n/a Session Timeout: n/a Session Cachesize: n/a Client-verify: n/a Client-verify weaken: n/a

Total 1 SSL server policy(s).


display ssl server-policy show ip ssh


2-318

Display Commandsdisplay startup

display startup

Displays the configuration file used at the current system startup and the configuration file(s) to be used at the next system startup.

HP Switch# display startup

Current startup saved-configuration file: flash:/svt-1.cfg

Next startup saved-configuration file for primary image: flash:/svt-1.cfg

Next startup saved-configuration file for secondary image: flash:/svt-2.cfg



display startup No equivalent ProVision software command


2-319

Display Commandsdisplay stp

display stp

Displays the MSTP status and statistics. Based on the MSTP status and statistics, you can analyze and maintain the network topology or check whether MSTP is working normally.

Spanning-tree protocol is enabled

HP Switch# display stp -------[CIST Global Info][Mode STP]------- CIST Bridge :32768.3ce5-a674-b433 Bridge Times :Hello 2s MaxAge 20s FwDly 15s MaxHop 20 CIST Root/ERPC :32768.3ce5-a674-b433 / 0 CIST RegRoot/IRPC :32768.3ce5-a674-b433 / 0 CIST RootPortId :0.0 BPDU-Protection :disabled Bridge Config- Digest-Snooping :disabled TC or TCN received :0 Time since last TC :1 days 22h:48m:24s

----[PortA1(A1)][DOWN]---- Port Protocol :0 Port Role :CIST Disabled Port Port Priority :128 Port Cost(Legacy) :0 Desg. Bridge/Port :32768.3ce5-a674-b433 / 128.1 Port Edged :Config=disabled / Active=disabled Point-to-point :Config=auto / Active=false Transmit Limit :10 packets/hello-time Protection Type :None MST BPDU Format :0 Port Config- Digest-Snooping :0 Num of Vlans Mapped :1 PortTimes :Hello 2s MaxAge 20s FwDly 15s MsgAge 0s RemHop 20 BPDU Sent :0 TCN: 0, Config: 0, RST: 0, MST: 0 BPDU Received :0 TCN: 0, Config: 0, RST: 0, MST: 0


display stp show spanning-tree


2-320


----[PortA2(A2)][DOWN]---- . . . ----[PortA3(A3)][DOWN]---- . . . .


HP Switch# show spanning-treeMultiple Spanning Tree (MST) InformationSTP Enabled : YesForce Version : MSTP-operationIST Mapped VLANs : 1-4094Switch MAC Address : 0024a8-d13a40Switch Priority : 32768Max Age : 20Max Hops : 20Forward Delay : 15Topology Change Count : 1Time Since Last Change : 20 minsCST Root MAC Address : 001083-847000CST Root Priority : 0CST Root Path Cost : 60000CST Root Port : 1IST Regional Root MAC Address : 0024a8-d13a40IST Regional Root Priority : 32768IST Regional Root Path Cost : 0IST Remaining Hops : 20Root Guard Ports :Loop Guard Ports : 2TCN Guard Ports :BPDU Protected Ports :BPDU Filtered Ports :PVST Protected Ports :PVST Filtered Ports : Prio | Designated HelloPort Type | Cost rity State | Bridge Time PtP Edge---- ----- ----- ----- ------ ----------- ---- --- -----1 100/1000T | 20000 128 Forwarding |001871-cdea00 2 Yes No2 100/1000T | Auto 128 Inconsistent |3 100/1000T | Auto 128 Disabled |4 100/1000T | Auto 128 Disabled |5 100/1000T | Auto 128 Disabled |6 100/1000T | Auto 128 Disabled |7 100/1000T | Auto 128 Disabled |8 100/1000T | Auto 128 Disabled |


2-321


Comware supports instances ranging from 0-31 and ProVision supports instances ranging from 0-16. For more information, see the latest Advanced

Traffic Management Guide for your switch.



2-322

Display Commandsdisplay stp abnormal-port

display stp abnormal-port

Displays information about ports blocked by spanning tree protection func-tions.

HP Switch# display stp abnormal-portMSTID Blocked Port Reason1 A1 ROOT-Protected2 A2 LOOP-Protected


HP Switch# show spanning-tree detailStatus and Counters - CST Port(s) Detailed InformationPort : 1Status : Up...Port : 2Status : UpBPDU Protection : NoBPDU Filtering : NoPVST Protection : NoPVST Filtering : NoErrant BPDU Count : 0Root Guard : NoLoop Guard : YesTCN Guard : NoMST Region Boundary : YesExternal Path Cost : 20000External Root Path Cost : 40000Administrative Hello Time : GlobalOperational Hello Time : 2AdminEdgePort : NoAuto Edge Port : YesOperEdgePort : NoAdminPointToPointMAC : TrueOperPointToPointMAC : YesAged BPDUs Count : 0Loop-back BPDUs Count : 0


display stp abnormal-port show spanning-tree detail show spanning-tree <port> detail


2-323

Display Commandsdisplay stp abnormal-port

TC ACK Flag Transmitted : 0TC ACK Flag Received : 1MST MST CFG CFG TCN TCNBPDUs Tx BPDUs Rx BPDUs Tx BPDUs Rx BPDUs Tx BPDUs Rx-------- -------- -------- -------- -------- --------- 3 0 24354 1682 0 13




2-324

Display Commandsdisplay stp bpdu-statistics display stp bpdu-statistics interface GigabitEthernet <port-num> display stp bpdu-statistics

display stp bpdu-statistics display stp bpdu-statistics interface GigabitEthernet <port-num> display stp bpdu-statistics interface GigabitEthernet <port-num> instance <instanceNUM, 1-32>

Displays the debug counters of the STP in different modes.

In MSTP mode :

• If MSTI or port is not specified, this command displays the BPDU statistics of all MSTIs on all ports. The displayed information is sorted by port name and by MSTI ID on each port.

• If a port is specified but not an MSTI, this command displays the BPDU statistics of all MSTIs on the port. The displayed information is sorted by MSTI ID.

• If both an MSTI ID and a port are specified, this command displays the BPDU statistics of the specified MSTI on the port.

In STP, RSTP, or PVST mode:

• If no port is specified, this command displays the BPDU statistics of on all ports. The displayed information is sorted by port name.

• If a port is specified, this command displays the BPDU statistics on the port.

HP Switch# stp bpdu-statistics interface 2 instance 2

Port: 2 Instance-independent:


display stp bpdu-statisticsdisplay stp bpdu-statistics interface GigabitEthernet <port-num>display stp bpdu-statistics interface GigabitEthernet <port-num> instance <instanceNUM, 1-32>

show spanning-tree detail


2-325


Type Count Last Updated --------------------------- ---------- -----------------

Invalid BPDUs 0 Looped-back BPDUs 0 MAX-aged BPDUs 0 TCN sent 0 TCN received 0 TCA sent 0 TCA received 0 Config sent 0 Config received 0 RST sent 0 RST received 0 MST sent 0 MST received 0

Instance 2:

Type Count Last Updated

--------------------------- ---------- ----------------- Timeout BPDUs 0 MAX-hoped BPDUs 0 TC detected 0 TC sent 0 TC received 0


HP Switch# show spanning-tree detailStatus and Counters - CST Port(s) Detailed InformationPort : 1Status : Up...Port : 2Status : UpBPDU Protection : NoBPDU Filtering : NoPVST Protection : NoPVST Filtering : NoErrant BPDU Count : 0Root Guard : NoLoop Guard : YesTCN Guard : NoMST Region Boundary : YesExternal Path Cost : 20000External Root Path Cost : 40000


2-326


Administrative Hello Time : GlobalOperational Hello Time : 2AdminEdgePort : NoAuto Edge Port : YesOperEdgePort : NoAdminPointToPointMAC : TrueOperPointToPointMAC : YesAged BPDUs Count : 0Loop-back BPDUs Count : 0TC ACK Flag Transmitted : 0TC ACK Flag Received : 1MST MST CFG CFG TCN TCNBPDUs Tx BPDUs Rx BPDUs Tx BPDUs Rx BPDUs Tx BPDUs Rx-------- -------- -------- -------- -------- --------- 3 0 24354 1682 0 13




2-327

Display Commandsdisplay stp brief display stp instance <instance-id> brief display stp instance <instance-id> interface GigabitEthernet

display stp brief display stp instance <instance-id> brief display stp instance <instance-id> interface GigabitEthernet <interface-id> brief display stp instance <instance-id> interface GigabitEthernet <interface-id> brief display stp instance <instance-id> interface GigabitEthernet <interface-id> to GigabitEthernet <interface-id> brief display stp instance <instance-id> slot <slot-id> brief display stp interface GigabitEnterface <port-num> brief display stp interface GigabitEnterface <port-num> to GigabitEnterface <port-num> brief

Displays brief information about spanning tree status and statistics.

Spanning-tree protocol is enabledHP Switch# display stp brief MSTID Port Role STP State Protection 1 1 Designated Blocking No 2 2 Disabled Disabled No


display stp briefdisplay stp instance <instance-id> briefdisplay stp instance <instance-id> interface GigabitEthernet <interface-id> briefdisplay stp instance <instance-id> interface GigabitEthernet <interface-id> briefdisplay stp instance <instance-id> interface GigabitEthernet <interface-id> to GigabitEthernet <interface-id> briefdisplay stp instance <instance-id> slot <slot-id> briefdisplay stp interface gigabitEnterface <port-num> briefdisplay stp interface GigabitEnterface <port-num> to GigabitEnterface <port-num> brief

show spanning-tree configshow spanning-tree <PORT-LIST> detail


2-328

Display Commandsdisplay stp brief display stp instance <instance-id> brief display stp instance <instance-id> interface GigabitEthernet

Spanning-tree protocol is disabledHP Switch# display stp briefProtocol Status :disabledProtocol Std. :IEEE 802.1sVersion :0Bridge-Prio. :32768MAC address :000fe2-008048Max age(s) :20Forward delay(s) :15Hello time(s) :2Max hops :20


HP Switch# show spanning-tree configMultiple Spanning Tree (MST) Configuration InformationSTP Enabled [No] : YesForce Version [MSTP-operation] : MSTP-operationDefault Path Costs [802.1t] : 802.1tMST Configuration Name : 1cc1decfbc80MST Configuration Revision : 0 Switch Priority : 32768Forward Delay [15] : 15 Hello Time [2] : 2Max Age [20] : 20 Max Hops [20] : 20 | Path Prio Admin Auto Admin Hello Root TCN BPDUPort Type | Cost rity Edge Edge PtP Time Grd Grd Flt---- ---- + ---- ---- ---- ----- ---- ----- ---- ---- --- 1 10/100TX | Auto 128 No Yes True Global No No No2 10/100TX | Auto 128 No Yes True Global No No No3 10/100TX | Auto 128 No Yes True Global No No No. . . . . . . . . . .7 10/100TX | Auto 128 No Yes True Global No No No

ProVision accepts interface range as 1-8. Comware accpets interface range as "GigabitEthernet1/0/1 to GigabitEthernet1/0/8".

CIST RootPortId and MSTI RootPortId are represented differently in ProVi-sion and Comware.




2-329

Display Commandsdisplay stp down-port

display stp down-port

Displays information about ports shut down by spanning tree protection functions.

HP Switch# display stp down-port Down Port Reason 4 BPDU-Protected 5 BPDU-Protected

Operating Notes

ProVision does not support Format-Frequency.



display stp down-port No equivalent ProVision software command


2-330

Display Commandsdisplay stp history display stp history slot <slot-number> display stp instance <instance-id> history slot <slot-no> display

display stp history display stp history slot <slot-number> display stp instance <instance-id> history slot <slot-no> display stp instance <instance-id> history

display stp history displays the historical port role calculation information of all MSTIs.

display stp history slot slot-number displays the statistics of the port’s history information of all the MSTIs of a given slot when stp protocol is enabled.

display stp instance instance-id history displays the historical port role information of the specified MSTI when stp protocol is enabled.

display stp instance instance-id history slot slot-number displays the statistics of the port’s history information of the specified MSTI of a given slot when stp protocol is enabled.

HP Switch# display stp history

display stp history

--------------- STP slot 1 history trace ---------------

------------------- Instance 0 -------------------

Port 1 Role change :Disa->Desi Time :2012/05/28 09:47:23 Port priority :32768.002347-b4cb80 0 32768.002347-b4cb80 0 32768.002347-b4cb80 128.1

------------------- Instance 1 -------------------

Port 1 Role change :Disa->Desi Time :2012/05/28 09:47:23 Port priority :32768.002347-b4cb80 0 32768.002347-b4cb80 48.1


display stp history No equivalent ProVision software command


2-331

Display Commandsdisplay stp history display stp history slot <slot-number> display stp instance <instance-id> history slot <slot-no> display

HP Switch# display stp history slot A


------------------- Instance 0 -------------------


------------------- Instance 1 -------------------

Port 1 Role change :Disa->Desi Time :2012/05/28 09:47:23 Port priority :32768.002347-b4cb80 0 32768.002347-b4cb80 48.1

HP Switch# display stp instance 0 history


------------------- Instance 0 -------------------




2-332


display stpdisplay stp instance <instance-id> interface GigabitEthernet 1/0/1/display stp slot <slot-num>

Displays MSTP status and statistics.

HP Switch# display stpProtocol Status : Disabled Protocol Std. : IEEE802.1s Version : 3 CIST Bridge-Prio : 32768 MAC Address : 0021f7-06ab00 Max age (s) : 2000 Forward delay (s) : 1500 Hello Time(s) : 200 Max Hops : 20


HP Switch# show spanning-treeMultiple Spanning Tree (MST) InformationSTP Enabled : YesForce Version : MSTP-operationIST Mapped VLANs : 1-4094Switch MAC Address : 0024a8-d13a40Switch Priority : 32768Max Age : 20Max Hops : 20Forward Delay : 15Topology Change Count : 1Time Since Last Change : 20 minsCST Root MAC Address : 001083-847000CST Root Priority : 0CST Root Path Cost : 60000CST Root Port : 1IST Regional Root MAC Address : 0024a8-d13a40IST Regional Root Priority : 32768


display stpdisplay stp instance <instance-id> interface GigabitEthernet 1/0/1/display stp slot <slot-num>

show spanning-tree


2-334

Display Commandsdisplay stp instance <instanceid> tc display stp instance <instanceid> tc slot <slot-no> display stp tc

display stp instance <instanceid> tc display stp instance <instanceid> tc slot <slot-no> display stp tc

Displays the STP information of a port under a particular instance when STP is enabled.

HP Switch# display stp instance 0 tc

-------------- STP slot A TC or TCN count ------------- MSTID Port Receive Send 0 A1 2 2

-------------- STP slot B TC or TCN count ------------- MSTID Port Receive Send

-------------- STP slot C TC or TCN count ------------- MSTID Port Receive Send

HP Switch# display stp instance 1 tc slot A

-------------- STP slot A TC or TCN count ------------- MSTID Port Receive Send 1 A2 0 2

HP Switch# display stp tc slot B-------------- STP slot B TC or TCN count ------------- MSTID Port Receive Send 0 B1 2 2 1 B2 0 2



display stp instance <instanceid> tcdisplay stp instance <instanceid> tc slot <slot-no>display stp tc



2-335

Display Commandsdisplay stp region-configuration

display stp region-configuration

Displays effective configuration information of the MST region, including the region name, revision level, and user-configured VLAN-to-instance mappings. Related commands: instance, region-name, revision-level, and vlan-mapping modulo.

Spanning-tree protocol is enabledHP Switch# display stp region-configurationOper ConfigurationFormat selector :0Region name :helloRevision level :0Configuration digest :0x5f762d9a46311effb7a488a3267fca9fInstance Vlans Mapped0 21 to 40941 1 to 102 11 to 20

Spanning-tree protocol is diabledHP Switch# display stp region-configurationOper configuration Format selector :0 Region name :3ce5a6761a00 Revision level :0 Configuration digest :

Instance Vlans Mapped 1 1 to 4094


HP Switch# show spanning-tree mst-configMST Configuration Identifier InformationMST Configuration Name : 1cc1decfbc80MST Configuration Revision : 0MST Configuration Digest : 0xC8DB46AEBEA5F48799BD2D8B0E1BCA54IST Mapped VLANs : 1-110,112-299,301-4094Instance ID Mapped VLANs----------- -------------------------------------------------11 111,300


display stp region-configuration show spanning-tree mst-config


2-336

Display Commandsdisplay stp region-configuration




2-337

Display Commandsdisplay stp root

display stp root

Displays the root bridge information of all MSTIs.

Spanning-tree protocol is enabledHP Switch# display stp rootMSTID Root Bridge ID ExtPathCost IntPathCost Root Port0 00e0fc-0e6554 200200 0 A1

Spanning-tree protocol is disabledHP Switch# display stp rootHP Switch#


HP Switch# show spanning-tree instance 11MST Instance InformationInstance ID : 11Mapped VLANs : 111,300Switch Priority : 32768Topology Change Count : 2Time Since Last Change : 4 minsRegional Root MAC Address : 1cc1de-cfbc80Regional Root Priority : 32768Regional Root Path Cost : 400000Regional Root Port : This switch is rootRemaining Hops : 20DesignatedPort Type Cost Priority Role State Bridge---- ----- ---- --------- -------- ------ ---------1 10/100TX 200000 128 Root Forwarding 1cc1de-cfbc802 10/100TX 200000 128 Designated Forwarding 1cc1de-02a7003 10/100TX Auto 112 Designated Forwarding 1cc1de-02a7004 10/100TX Auto 128 Disabled Disabled




display stp root show spanning-tree instance <instance-id>show spanning-tree detail


2-338

Display Commandsdisplay switchover state

display switchover state

Displays the backup state of the specified main board. This command displays the backup state on the AMB or the standby main board (SMB) depending on the slot number specified. The backup state of the AMB is displayed if no slot number is specified.

Field Descriptions

Master HA State to Slot: Backup state between the active main board (AMB) and the standby main board (SMB).

Slave HA State: Indicates that the output information is generated by the SMB and describes the switchover state of the SMB.

Operating Notes

In Comware, either 0 or 1 displays for the slot, depending on which board is active (master or slave).

For more information about redundancy, see the “Chassis Redundancy (8200zl Switches)” chapter in the latest Management and Configuration Guide for your switch.


display switchover state show redundancy

HP Switch-8200# display switchover stateMaster HA state to slot [0] : Relative backup to slave

HP Switch-8200# display switchover state slot 0Slave HA State: Receiving realtime data

HP Switch-8200# display switchover state slot 1Master HA State to Slot [0]: Relative backup to slave

HP Switch-3800# display switchover stateComware: The corresponding ProVision command is "show redundancy".


2-339

Display Commandsdisplay switchover state


display switchover state Field Mappings.


HP Switch(config)# show redundancy

Settings--------Mgmt Redundancy : Nonstop switching enabledRapid Switchover Stale Timer : 0

Statistics----------Failovers : 0Last Failover :

Slot Module Description Status SW Version Boot Image---- ---------------------------------------- -------- ------------ ----------MM1 HP J9092A Management Module 8200zl Active K.15.01.000x PrimaryMM2 HP J9092A Management Module 8200zl Standby K.15.01.000x Primary

FM1 HP J9093A Fabric Module 8200zl EnabledFM2 HP J9093A Fabric Module 8200zl Enabled


Master HA State to Slot Status

Slave HA State Status


2-340

Display Commandsdisplay system-failure

display system-failure

HP Switch# display system-failure

System failure handling method: reboot


HP Switch# show boot-history

Mgmt Module 1 -- Saved Crash Information (most recent first):=============================================================Mgmt Module 1 in Active Mode went down: 11/07/09 14:48:36Operator warm reload from CONSOLE session.Mgmt Module 1 in Active Mode went down: 11/07/09 11:43:10Operator cold reboot from CONSOLE session.

Mgmt Module 2 -- Saved Crash Information (most recent first):=============================================================No Saved Crash Information

Operating Notes





display system-failure show boot-history


2-341

Display Commandsdisplay this

display this

Displays valid configuration information under the current view. Use this command to check whether your configuration has taken effect. Valid config-uration that is the same as the default is not displayed. Invalid configuration is not displayed. Execution of this command in any user interface view displays the valid configuration in all the user interfaces. Execution of this command in any VLAN view displays the configurations of all the created VLANs.

HP Switch# display this

vlan 1 name "DEFAULT_VLAN" no untagged 1-2,48 untagged 3-47 ip address dhcp-bootp exit

vlan 10 name "VLAN10" untagged 1,48 ip address 10.10.10.3 255.255.255.0 ip igmp exit

vlan 30 name "VLAN30" untagged 2 ip address 30.30.30.2 255.255.255.0 ip igmp ip rip 30.30.30.2 ip pim-sparse ip-addr any exit

exit



display this No equivalent ProVision software command


2-342

Display Commandsdisplay transceiver alarm interface

display transceiver alarm interface

Displays the current alarm information of a single or all transceivers.

Field Descriptions

RX loss of signal: Incoming (RX) signal is lost.

TX fault: Transmit (TX) fault

RX power high: Incoming (RX) power level is high.

RX power low: Incoming (RX) power level is low.

TX power high: TX power is high.

TX power low: TX power is low.

TX bias low: TX bias current is low. TX bias high: TX bias current is high.

Temp high: Temperature is high.

Temp low: Temperature is low.

Voltage high: Voltage is high.

Voltage low: Voltage is low.

Transceiver info I/O error: Transceiver information read and write error

Transceiver info checksum error: Transceiver information checksum error

Transceiver type and port configuration mismatch: Transceiver type does not match port configuration.

Transceiver type not supported by port hardware: Transceiver type is not sup-ported on the port.


display transceiver alarm interface show interface transceiver detail

HP Switch(config)# display transceiver alarm interface g1G1 transceiver current alarm information: Rx power low


2-343


RX loss of signal: Incoming (RX) signal is lost.

RX not ready: RX is not ready

RX CDR loss of lock: RX clock cannot be recovered.

TX fault: TX fault

TX not ready: TX is not ready.

TX CDR loss of lock: TX clock cannot be recovered.

Module not ready: Module is not ready.

APD supply fault: APD (Avalanche Photo Diode) supply fault

TEC fault: TEC (Thermoelectric Cooler) fault

Wavelength unlocked: Wavelength of optical signal exceeds the manufacturer’s tolerance.

RX power high: RX power is high.

RX power low: RX power is low.

TX power high: TX power is high.

TX power low: TX power is low.

TX bias high: TX bias current is high.

TX bias low: TX bias current is low.

Temp high: Temperature is high.

Temp low: Temperature is low.

Voltage high: Voltage is high.

Voltage low: Voltage is low.

Transceiver info I/O error: Transceiver information read and write error

Transceiver info checksum error: Transceiver information checksum error

Transceiver type and port configuration mismatch: Transceiver type does not match port configuration.

Transceiver type not supported by port hardware: Transceiver type is not sup-ported on the port.


2-344


Operating Notes

Possible values for HPN and H3C alarms/errors are not the same.

The following alarms/errors are not supported in H3C devices, and they will be displayed in HPN output, if present:

• WIS local fault

• Receive optical power fault

• PMA/PMD receiver local fault

• PMA/PMD transmitter local fault

• PCS receive local fault

• PCS transmit local fault

• PHY XS receive local fault

• Laser bias current fault

• Laser temperature fault

• Laser output power fault

HPN does not support the following alarms/errors, and they are not displayed in the display command output:

• RX not ready

• RX CDR loss of lock

• TX not ready

• TX CDR loss of lock

• Module not ready

• APD supply fault

• TEC fault

• Wavelength unlocked

The following values are supported on both HPN and H3C devices:

• Temp high

• Temp low

• Voltage high

• Voltage low

• TX bias high

• TX bias low

• TX power high

• TX power low

• RX power high


2-345


• RX power low

• Transceiver info I/O error

• Transceiver info checksum error

• Transceiver type and port configuration mismatch

• Transceiver type not supported by port hardware

• RX loss of signal

• TX fault

For more information on transceivers, see the “Troubleshooting” chapter in the latest Management and Configuration Guide for your switch.


HP Switch(config)# show interfaces transceiver 23 detail

Transceiver in 23 Interface Index : 24 Type : 10GbE-LR Model : J8437A Connector type : SC Wavelength : Channel #0: 1310nm, #1:0nm, #2:0nm, #3:0nm Transfer distance : 10000m (SM) Diagnostic support : DOM Serial number : ED456SS987

Status Temperature : 32.754C TX Bias : 42.700mA TX Power : 0.5192mW, -2.847dBm RX Power : 0.0040mW, -23.979dBm

Recent Alarms:

Rx power low alarm Rx power low warning

Recent errors: Receive optical power fault PMA/PMD receiver local fault PMA/PMD transmitter local fault PCS receive local fault PHY XS transmit local fault Time stamp : Mon Mar 7 16:26:06 2011


2-346


display transceiver alarm interface Field Mappings.



Rx not ready n/a

RX CDR loss of lock n/a

TX not ready n/a

TX CDR loss of lock n/a

Module not ready n/a

APD supply fault n/a

TEC fault n/a

Wavelength unlocked n/a

Temp high Temp high

Temp low Temp low

Voltage high Voltage high

Voltage low Voltage low

TX bias high TX bias high

TX bias low TX bias low

TX power high TX power high

TX power low Tx power low

RX power high RX power high

RX power low RX power low

RX loss of signal RX loss of signal

TX fault TX fault


2-347

Display Commandsdisplay transceiver diagnosis interface

display transceiver diagnosis interface

Displays the currently measured value of digital diagnosis parameters of H3C customized anti-spoofing pluggable optical transceivers.

Field Descriptions

transceiver diagnostic information: Digital diagnosis information of the trans-ceiver plugged in the interface.

Current diagnostic parameters: Current diagnostic parameters.

Temp.(°C): Digital diagnosis parameter-temperature, in °C, with the precision to 1°C.

Voltage(V): Digital diagnosis parameter-voltage, in V, with the precision to 0.01 V.

Bias(mA): Digital diagnosis parameter-bias current, in mA, with the precision to 0.01 mA.

RX power(dBM): Digital diagnosis parameter-RX power, in dBM, with the precision to 0.01 dBM.

TX power(dBM): Digital diagnosis parameter-TX power, in dBM, with the pre-cision to 0.01 dBM.


display transceiver diagnosis interface show interface transceiver [<port> | detail ]

HP Switch(config)# display transceiver diagnosis interface g1G1 transceiver diagnostic information: Current diagnostic parameters: Temp.(C) Voltage(V) Bias(mA) RX power(dBM) TX power(dBM) 25.000 0.0000 7.864 -inf -2.350

HP Switch(config)# display transceiver diagnosis interface g4G4 transceiver diagnostic information:Error: The transceiver does not support this function.


2-348


Operating Notes



display transceiver diagnosis interface Field Mappings.


transceiver diagnostic information Transceiver in

Current diagnostic parameters Status

Temp. (°C) Temperature

Voltage(V) Voltage

Bias(mA) TX Bias

HP Switch(config)# sh int transceiver 24 detailTransceiver in 24 Interface Index : 124 Type : SFP+LR Model : J9151A Connector Type : LC Wavelength : 1310nm Transfer Distance : 10.0km (9um), Diagnostic Support : DOM Serial Number : CN847GV009

Status Temperature : 35.148C Voltage : 3.2348V Tx Bias : 41.952mA Tx Power : 0.4047mW, -3.929dBm Rx Power : 0.0006mW, -32.218dBm

Recent Alarms : Rx power low alarm Rx power low warning

Recent Errors : Rx loss of signal

Time Stamp : Mon Jun 11 03:00:27 2012


2-349



RX power(dBM) RX Power

TX power(dBM) TX Power



2-350

Display Commandsdisplay transceiver interface

display transceiver interface

Displays main parameters of a single or all pluggable transceivers.

Field Descriptions

transceiver information: Pluggable transceiver information

Connector Type: Type of the connectors of the transceiver:

• Optical connectors, including SC (SC connector, developed by NTT) and LC (LC connector, 1.25 mm/RJ-45 optical connector developed by Lucent).

• Other connectors, including RJ-45 and CX 4.

Wavelength(nm): • Optical transceiver: Central wavelength of the laser sent, in nm. If the

transceiver supports multiple wavelengths, every two wavelength values are separated by a comma.

• Electrical transceiver: Displayed as N/A.

Transfer distance(xx): Transfer distance, with xx representing km for single-mode transceivers and m for other transceivers. If the transceiver supports multiple transfer medium, every two values of the transfer distance are separated by a comma. The corresponding transfer medium is included in the bracket following the transfer distance value. The following are the transfer media:

• 9 um: 9/125 um single-mode fiber

• 50 um: 50/125 um multi-mode fiber


display transceiver interface show interface transceiver [<port> | detail ]

HP Switch(config)# display transceiver interface g1G1 transceiver information: Transceiver Type : 10GbE-SR Connector Type : SC Wavelength(nm) : 850nm Transfer Distance(m) : 300m (MM generic) Digital Diagnostic Monitoring : YES Vendor Name : n/a Ordering Name : J8436A


2-351


• 62.5 um: 62.5/125 um multi-mode fiber

• TP: Twisted pair

• CX4: CX4 cable

Digital Diagnostic Monitoring: Whether the digital diagnosis function is sup-ported, where:

• YES: Supported

• NO: Not supported

Vendor Name: Vendor name or name of the vendor who customizes the trans-ceiver:

• H3C anti-spoofing transceiver (customized): H3C is displayed.

• Other transceivers: The vendor name is displayed; if the vendor is unknown or illegal, unknown is displayed.

Ordering Name: • H3C devices: Switch model is displayed

• Other devices: N/A is displayed.

Operating Notes



2-352



display transceiver interface Field Mappings.



transceiver information Transceiver in <int>

Transceiver Type Type

Connector Type Connector type

Wavelength(nm) Wavelength

Transfer distance (xx) Transfer distance

Digital Diagnostic Monitoring Diagnostic support

Vendor Name n/a

Ordering Name Model







2-353

Display Commandsdisplay transceiver manuinfo interface

display transceiver manuinfo interface

Displays the transceiver manufacturing information of the specified trans-ceiver on an interface or of all the interfaces in the device.

Field Descriptions

Manu. Serial Number: Serial number of the transceiver, generated during device commissioning

Manufacturing Date: Commissioning date of the transceiver, which is the date of the computer used for commissioning the switch

Vendor Name: Name of vendor who customizes the transceiver

Operating Notes

The manufacturing date is displayed in the following formats:

• Older transceivers—displayed in yyyymmdd format

• Newer transceivers—displayed in yymmddll or yymmdd format.



display transceiver manuinfo interface show interface transceiver [<port> | detail ]

HP Switch(config)# display transceiver manuinfo interface g1G1 transceiver manufacture information: Manu. Serial Number : MY902IF107 Manufacturing Date : 081118 Vendor Name : n/a


2-354

Display Commandsdisplay transceiver manuinfo interface


display transceiver diagnosis manuinfo Field Mappings.



Manu. Serial Number Serial number

Manufacturing Date n/a

Vendor Name n/a







2-355

Display Commandsdisplay user-bind

display user-bind

Displays user bind address.

HP Switch# display user-bind

Total entries found: 1 MAC IP Vlan Port Status 0030c1-7f49c0 120.93.49.7 2 1


HP Switch# show ip source-lockdown bindingsDynamic IP Lockdown (DIPLD) BindingsMac Address IP Address VLAN Port Not in HW----------- ---------- ----- ----- ---------001122-334455 10.10.10.1 1111 X11005544-332211 10.10.10.2 2222 Trk11 YES. . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Notes




display user-bind show ip source-lockdown bindings


2-356

Display Commandsdisplay vlan

display vlan

Displays vlan-id for the existing vlan only. If it is consecutive it displays as a range.

HP Switch# display vlanTotal 2 VLAN exist(s).The following VLANs exist: 1(default), 7,

HP Switch# display vlan staticTotal 2 VLAN exist(s).The following VLANs exist: 1(default), 7,

HP Switch# display vlan 7VLAN ID: 7VLAN Type: staticRoute Interface: n/aDescription: VLAN 0007Name: VLAN7Tagged Ports: 3 5 7 10 16 19Untagged Ports: 8 11 18 21 22

HP Switch# display vlan 8-10

VLAN(s) do(es) not exist.

HP Switch# display vlan dynamic

No dynamic VLAN exists!

HP Switch# display vlan dynamic

Total 2 dynamic VLAN exist(s).

The following dynamic VLANs exist:

2, 4,



display vlan No equivalent ProVision software command


2-357

Display Commandsdisplay vrrp

display vrrp

Displays vrrp details like VLAN, status, priority, and router ip address.

HP Switch# display vrrp

IPv4 Standby Information:

Run Mode : Standard Run Method : Virtual MAC

Total number of virtual routers : 2

Interface VRID State Run Adver Auth Virtual Pri Timer Type IP -------------------------------------------------------------Vlan4 4 Initialize 144 1 None 14.4.1.1 Vlan4 5 Initialize 154 1 None 14.4.2.1

Field Descriptions:

Run Mode: Current VRRP working mode, including:

• Standard: Standard protocol mode

• Load Balance: Load balancing mode

Run Method: Current VRRP running mode, including

• Real MAC: Real MAC mode, which means the virtual IP address of the VRRP group is mapped to the real MAC address of the interface.

• Virtual MAC: Virtual MAC mode, which means the virtual IP address of the VRRP group is mapped to the virtual MAC address.

Total number of virtual routers: Number of VRRP groups

Interface: Interface to which the VRRP group belongs

VRID: ID of the VRRP group

Run Pri: Running priority of the router, or in other words, the current priority of the router. With VRRP tracking configured, when the state of the monitored interface or track entry changes, the priority of the router changes.


display vrrp show vrrp


2-358

Display Commandsdisplay vrrp

Adver. Timer: VRRP advertisement interval, in seconds

Auth Type: Authentication type, including

• None: No authentication

• Simple: Simple text authentication

• MD5: MD5 authentication

Virtual IP: Virtual IP address of the VRRP group


HP Switch# show vrrp config

VRRP Global Configuration Information

VRRP Enabled : YesTraps Enabled : YesVirtual Routers Respond to Ping Requests : YesVRRP Nonstop Enabled: Yes

VRRP Virtual Router Configuration Information

Vlan ID : 10Virtual Router ID : 1

Administrative Status [Disabled] : EnabledMode [Uninitialized] : BackupPriority [100] : 150Advertisement Interval [1] : 1Preempt Mode [True] : TruePreempt delay time : 0Respond to Virtual IP Ping Requests [Yes] : YesPrimary IP Address : Lowest

IP Address Subnet Mask--------------- --------------- 10.0.202.87 255.255.0.0




2-359

Display Commandsdisplay vrrp interface <interface-type> vrid <virtual routerid>

display vrrp interface <interface-type> vrid <virtual routerid>

HP Switch# display vrrp interface vlan-interface 4 vrid 1IPv4 Standby Information: Run Mode : Standard Run Method : Virtual MAC Info: No such standby!HP-E3500-24-PoE# display vrrp interface vlan-interface 4 vrid 4 IPv4 Standby Information: Run Mode : Standard Run Method : Virtual MAC Interface VRID State Run Adver Auth Virtual Pri Timer Type IP------------------------------------------------------------- Vlan4 4 Initialize 144 1 None 14.4.1.1


HP Switch# show vrrp vlan 2 vrid 1 configVRRP Virtual Router Configuration InformationVlan ID : 2Virtual Router ID : 1Administrative Status [Disabled] : EnabledMode [Uninitialized] : BackupPriority [100] : 150Advertisement Interval [1] : 1Preempt Mode [True] : TruePreempt delay time : 0Respond to Virtual IP Ping Requests [Yes] : YesPrimary IP Address : LowestIP Address Subnet Mask--------------- ---------------10.0.202.87 255.255.0.0




display vrrp interface <interface-type> vrid <virtual routerid>

show vrrp<interface-type> vrid <virtual routerid>


2-360

Display Commandsdisplay vrrp statistics

display vrrp statistics

Displays vrrp counters like invalid type packets received, priority zero packets received and sent on each vrrp router configured.

HP Switch# display vrrp statistics

Interface : Vlan-interface3 VRID : 2 CheckSum Errors : 0 Version Errors : 0 Invalid Type Pkts Rcvd : 0 Advertisement Interval Errors : 0 IP TTL Errors : 0 Auth Failures : n/a Invalid Auth Type : n/a Auth Type Mismatch : 0 Packet Length Errors : 0 Address List Errors : 0 Become Master : 0 Priority Zero Pkts Rcvd : 0 Adver Rcvd : 0 Priority Zero Pkts Sent : 0 Adver Sent : n/a

Field Descriptions:

Interface: Interface to which the VRRP group belongs

VRID: Serial number of the VRRP group

CheckSum Errors: Number of packets with checksum errors

Version Errors: Number of packets with version errors

Invalid Type Pkts Rcvd: Number of packets with incorrect packet type

Advertisement Interval Errors: Number of packets with advertisement interval errors

IP TTL Errors: Number of packets with TTL errors

Auth Failures: Number of packets with authentication failures

Invalid Auth Type: Number of packets with authentication failures due to invalid authentication types

Auth Type Mismatch: Number of packets with authentication failures due to mismatching authentication types


display vrrp statistics show vrrp statistics


2-361

Display Commandsdisplay vrrp statistics

Packet Length Errors: Number of packets with VRRP packet length errors

Address List Errors: Number of packets with virtual IP address list errors

Become Master: Number of times that the router worked as the master

Priority Zero Pkts Rcvd: Number of received advertisements with the priority of 0

Advertise Rcvd: Number of received advertisements

Priority Zero Pkts Sent: Number of advertisements with the priority of 0 sent

Advertise Sent: Number of advertisements sent


HP Switch# show vrrp statistics global

VRRP Global Statistics Information

VRRP Enabled : YesProtocol Version : 2Invalid VRID Pkts Rx : 0Checksum Error Pkts Rx : 0Bad Version Pkts Rx : 0

For more information, see the the latest Multicast and Routing Guide for your switch.



2-362

Display Commandsdisplay vrrp statistics interface <interface-type> vrid <virtual router-id>

display vrrp statistics interface <interface-type> vrid <virtual router-id>

Displays statistics about VRRP group(s). If you specify both an interface and a VRRP group, only the statistics about the specified VRRP group on the interface are displayed. If you only specify an interface, the statistics about all the VRRP groups on the interface are displayed. If you specify neither, the statistics about all the VRRP groups on the router are displayed.

HP Switch# display vrrp statistics interface Vlan 3

Interface : Vlan-interface3VRID : 2CheckSum Errors : 0 Version Errors : 0Invalid Type Pkts Rcvd : 0 Advertisement Interval Errors : 0IP TTL Errors : 0 Auth Failures : n/aInvalid Auth Type : n/a Auth Type Mismatch : 0Packet Length Errors : 0 Address List Errors : 0Become Master : 0 Priority Zero Pkts Rcvd : 0Adver Rcvd : 0 Priority Zero Pkts Sent : 0Adver Sent : n/a


HP Switch# show vrrp statistics globalVRRP Global Statistics InformationVRRP Enabled : YesProtocol Version : 2Invalid VRID Pkts Rx : 0Checksum Error Pkts Rx : 0Bad Version Pkts Rx : 0




display vrrp statistics interface <interface-type> vrid <virtual router-id>

show vrrp statistics global


2-363

Display Commandsdisplay vrrp verbose

display vrrp verbose

Displays detailed state information of VRRP group(s). If you specify both an interface and a VRRP group, only the state information of the specified VRRP group on the interface is displayed. If you only specify an interface, the state information of all the VRRP groups on the interface is displayed. If you specify neither, the state information of all the VRRP groups on the router is displayed.

HP Switch# display vrrp verbose

IPv4 Standby Information: Run Mode : Standard Run Method : Virtual MAC Total number of virtual routers : 2

Interface Vlan-interface4 VRID : 4 Adver Timer : 1 Admin Status : UP State : Initialize Config Pri : 144 Running Pri : None Preempt Mode : YES Delay Time : 0 Auth Type : None Key : Virtual IP : 14.4.1.1 Virtual MAC : 00005e-000104 Master IP :

Interface Vlan-interface4 VRID : 5 Adver Timer : 1 Admin Status : UP State : Initialize Config Pri : 154 Running Pri : None Preempt Mode : YES Delay Time : 0 Auth Type : None Key : Virtual IP : 14.4.2.1 Virtual MAC : 00005e-000105 Master IP :

VRRP Track Information: Track Interface: Port23 State : Down Pri Reduced : n/a Track Interface: Vlan2 State : Down Pri Reduced : n/a


display vrrp verbose show vrrp


2-364

Display Commandsdisplay vrrp verbose


HP Switch# show vrrp

VRRP Global Statistics Information

VRRP Enabled : YesProtocol Version : 2Invalid VRID Pkts Rx : 0Checksum Error Pkts Rx : 0Bad Version Pkts Rx : 0Virtual Routers Respond To Ping Requests : Yes

VRRP Virtual Router Statistics Information

Vlan ID : 2Virtual Router ID : 1State : MasterUp Time : 25 secsVirtual MAC Address : 00005e-000101Master's IP Address : 10.0.102.87Associated IP Addr Count : 1 Near Failovers : 0Advertise Pkts Rx : 0 Become Master : 1Zero Priority Rx : 0 Zero Priority Tx : 0Bad Length Pkts : 0 Bad Type Pkts : 0Mismatched Interval Pkts : 0 Mismatched Addr List Pkts : 0Mismatched IP TTL Pkts : 0 Mismatched Auth Type Pkts : 00




3-1

Fundamental Commandsbackup startup-configuration

3

Fundamental Commands

backup startup-configuration

Used to backup the startup configuration file (used at the next system startup) to a specified TFTP server and to a specified filename.

HP Switch# backup startup-configuration to 120.93.49.9 test_newTFTP download in progress.

Related ProVision Software Command.

To upload the current startup configuration to a file named sw8200 in the config directory on drive “d” in a TFTP server with an IP address of 10.28.227.105, use the following command:HP Switch# copy startup-config tftp 10.28.227.105 d:\configs\sw8200

Operating Notes





backup startup-configuration copy startup-config tftp <ip-address> <file name>


3-2

Fundamental Commandsclock datetime

clock datetime

Used to set the current time and date of the device. You can leave the ss field blank when you specify the time parameters. This command accepts any input for the YYYY value. It displays the current time once the value is set. It displays a warning string if it is executed in Manager View. It is not available in Operator View, it is only available in Configure context.

HP Switch# clock datetime 8:8:8 7/7/7


HP Switch# clock set

Operating Notes





clock datetime clock set <Time[date] | Date[Time]>


3-3

Fundamental Commandsclock summer-time one-off

clock summer-time one-off

This command does not differ from the related ProVision software command.

HP Switch# clock summer-time

Operating Notes





clock summer-time clock summer-time


3-4

Fundamental Commandsclock summer-time repeating

clock summer-time repeating


HP Switch# clock summer-time

Operating Notes





clock summer-time repeating clock summer-time


3-5

Fundamental Commandsclock timezone

clock timezone


HP Switch# clock timezone

Operating Notes





clock timezone clock timezone


3-6

Fundamental Commandscommand accounting

command accounting

Used to enable command accounting.

HP Switch# command accounting


HP Switch# aaa accounting commands

Operating Notes




command accounting aaa accounting commands < stop-only | interim-update > radius


3-7

Fundamental Commandscommand authorization

command authorization

Used to enable command authorization.

HP Switch# command authorization


HP Switch# aaa authorization commands radius

Operating Notes




command authorization aaa authorization commands radius


3-8

Fundamental Commandscommand-alias enable

command-alias enable

Used to enable the command keyword alias function. By default, the command keyword alias function is enabled.

HP Switch# command-alias enable



command-alias enable No equivalent ProVision software command


3-9

Fundamental Commandscommand-alias mapping

command-alias mapping

Used to configure a command keyword alias. By default, a command keyword has no alias. By default, the command is enabled and not configurable. It is available in Manger view. It accepts "any string" (irrespective of whether it’s a valid command token or not). Cmdkey value range is 1-40 and AliasKey value range is 1-32.

HP Switch# command-alias mapping



command-alias mapping No equivalent ProVision software command


3-10

Fundamental Commandscopy

copy


HP Switch# copy config SOURCE_CONFIG_FILE_ON_SWITCH config DESTINATION_CONFIG_FILE_ON_SWITCH

Operating Notes





copy copy config SOURCE_CONFIG_FILE_ON_SWITCH config DESTINATION_CONFIG_FILE_ON_SWITCH


3-11

Fundamental Commandsdelete <startup-config>

delete <startup-config>

Used to delete config file from the system directory. This command can be executed from any context. The keyword 'delete' tab help text lists the config files which can be deleted. The command allows only deletion of config files and not other files. It does not support wildcards (like *.txt) and file names with URL’s. Deleted files cannot be restored.

HP Switch# delete config1


HP Switch# erase config

Operating Notes




delete <startup-config> erase config <file name>


3-12

Fundamental Commandsflow-control

flow-control


HP Switch# flow-control

Operating Notes





flow-control flow-control


3-13

Fundamental Commandsidle-timeout

idle-timeout

Used to set the idle-timeout timer. When it expires, user sessions are termi-nated. By default idle-timeout is disabled. The command supports only min-utes. And these minutes are the predefined set 0,1,5,10,15,20,30,60,120. The command is available in configure context. The default inactivity timer is 0 and means it is disabled.

HP Switch# idle-timeout 120


HP Switch# console inactivity-timer

Operating Notes




idle-timeout console inactivity-timer


3-14

Fundamental Commandsquit

quit

Used to return to a lower-level view. If the current view is operator mode, this command terminates the current connection and quits the system.

HP Switch# quitDo you want to log out [y/n]?


HP Switch# exit

Operating Notes




quit exit


3-15

Fundamental Commandsreboot

reboot

Used to reboot a module. If the slot keyword is not provided, the whole system reboots.

HP Switch# reboot slot A


HP Switch# boot

Operating Notes





reboot slot <slot num> boot


3-16

Fundamental Commandsreset saved-configuration

reset saved-configuration

Used to delete the startup configuration file saved on the storage medium of the switch. The command can be executed in manager mode.


HP Switch# erase startup

Operating Notes





reset saved-configuration erase startup


3-17

Fundamental Commandsrestore startup-configuration

restore startup-configuration

Used to download a configuration file from the specified TFTP server to the switch and specify the configuration file as the startup configuration file to be used at the next startup of the switch. The command is supported in manager mode. When you download a config file from a remote server which has same name as current active startup config file name (but both are not identical) then after downloading the file the switch reboots itself. In this case, the command triggers the download of the config file from the remote server but the next startup-configuration file is not configured.

A maximum of 3 config files can be stored on the switch. There are no restrictions on the file name.

HP Switch# restore startup-configuration from 120.93.49.9 restore_test

This will change the default configuration file to be used whenever the switch is rebooted. Continue[y/n]?


HP Switch# copy tftp startup-config

Operating Notes





restore startup-configuration copy tftp startup-config


3-18

Fundamental Commandsreturn

return

Used to return to user view from current view (non user view), as with the hot key ctrl+Z.

HP Switch# return


HP Switch# end

Operating Notes





return end


3-19

Fundamental Commandssave

save

Used to save the current configuration to the current startup config file. By default, the current configuration gets saved in the current start-up configu-ration file.


HP Switch# write memory

Operating Notes





save write memory


3-20

Fundamental Commandsschedule reboot at

schedule reboot at

Used to enable the scheduled reboot function of the whole system (including all cards) at a specific time and date. The command can be executed in manager mode. The supported date form is mm/dd[/[yy]yy]. The command cannot be executed if the date is not specified and specified reboot time is earlier than the current time.

HP Switch# schedule reboot at 14:00 04/13/2012 Reload scheduled at 14:00:10 04/13/2012 (in 0 days, 0 hours, 49 minutes)System will be rebooted at the scheduled time from secondary image.Do you want to continue [y/n]?


HP Switch# reload at 12:05 01/01/2012

Operating Notes




schedule reboot at reload at


3-21

Fundamental Commandsschedule reboot delay

schedule reboot delay

Used to enable the scheduled reboot function of the whole system (including all cards) and to set a reboot waiting time. The command can be executed in manager mode and accepts input in [[dd:]hh:]mmformat

HP Switch# schedule reboot delay 01:20 Reload scheduled in 0 days, 1 hours, 20 minutesSystem will be rebooted at the scheduled time from secondary image.Do you want to continue [y/n]?


HP Switch# reload after 04:14:00

Reload scheduled in 4 days, 14 hours, 0 minutes

This command will cause a switchover at the scheduled time to the other management module which may not be running the same software image and configurations. Do you want to continue [y/n]?

Operating Notes




schedule reboot delay reload after


3-22

Fundamental Commandsscreen-length

screen-length

Used to set the number of lines on the next screen. This command is executed in manager mode. The range for the number of lines supported is 2-1000.

HP Switch# screen-length


HP Switch# terminal length

Operating Notes




screen-length terminal length


3-23

Fundamental Commandsset authentication password

set authentication password


HP Switch# set authentication password

Operating Notes





set authentication password set authentication password


3-24

Fundamental Commandsspeed

speed

Used to set the transmission rate on the user interface. This command can be executed from configure mode. There is no default value. The lowest sup-ported value is 1200 bps. The configuration has to be saved and the switch has to be rebooted to make the configuration effective.

HP Switch# speed 9600

This command will take effect after saving the configuration and rebooting the system.


HP Switch# console baud-rate 19200


Operating Notes




speed (user interface view) console baud-rate


3-25

Fundamental Commandsstartup saved-configuration

startup saved-configuration

Used to specify the configuration file to be used at the next system startup. This command can be executed in manager mode.

HP Switch# startup saved-configuration test

This will change the default configuration file to be used whenever the switch is rebooted. Continue[y/n]?


HP Switch# startup-default secondary config config2HP Switch# show config filesConfiguration files:id | act pri sec | name---+-------------+-----------------------------------------1 | * * | config12 | * | config23 | |

Operating Notes

For more information, refer to the latest Basic Configuration Guide for your switch.



startup saved-configuration startup-default config <config file name>


3-26

Fundamental Commandssysname

sysname

Used to set the name of the device. Changing device name affects the prompt of the CLI. For example, if the device name is Sysname, the prompt of the user view is <Sysname>. Special characters are not allowed.

HP Switch# sysname


HP Switch# hostname

Operating Notes




sysname <name-string> hostname <name-string>


3-27

Fundamental Commandssystem-view

system-view

Used to enter system view from the current user view.

HP Switch# system-viewHP Switch(config)#


HP Switch# configure terminalHP Switch(config)#

Operating Notes




system-view configure terminal


3-28

Fundamental Commandstelnet

telnet


HP Switch# telnet

Operating Notes





telnet telnet


3-29

Fundamental Commandstelnet ipv6

telnet ipv6

Used to telnet to a remote IPv6 host. To stop the current Telnet login, press Ctrl+K or use the quit command. This command supports both ipv6 and ipv4 formats with the given string name.

HP Switch# telnet ipv6 hostname

HP Switch# telnet ipv6 addr


HP Switch# telnet hostname

Operating Notes




telnet ipv6 telnet


3-30

Fundamental Commandstelnet server enable

telnet server enable

Used to enable the Telnet server. The Telnet server is enabled by default. This command is executed in manager mode.

HP Switch# telnet server enable


HP Switch# telnet-server

Operating Notes




telnet server enable telnet-server


3-31

Fundamental Commandsterminal type

terminal type

Used to configure the type of terminal display under the current user interface. By default, the terminal display type is VT100. This command can be executed in manager mode. The configuration becomes effective after it is saved and the system is rebooted.

HP Switch# terminal type ansi



HP Switch# console terminal vt100


Operating Notes




terminal type console terminal


3-32

Fundamental Commandstftp

tftp

Used to download a specified file from the TFTP server to the local device or upload a specified local file to the TFTP server in an IPv4 network. This command can be executed only from config context. Downloading a file from the tftp server to any user given file or uploading any file to the tftp server is supported only for specific type of files. Comware command allows . In ProVision this functionality is supported only for specific type of files. The destination file parameter is mandatory.

HP Switch# tftp 120.93.49.9 put config tftp_testTFTP download in progress.HP Switch# tftp 120.93.49.9 get config2 tftp_testHP Switch# tftp 120.93.49.9 sget test tftp_testEnter [email protected]'s password:Attempting username/password authentication...00000KFile transfer terminated by user request.


HP Switch# copy tftp flash 10.29.227.13 flashDevice will be rebooted, do you want to continue [y/n]?

Operating Notes





tftp copy


3-33

Fundamental Commandstftp ipv6

tftp ipv6

Used to download a specified file from a TFTP server or upload a specified local file to a TFTP server in an IPv6 network. This command can be executed only from config context. Downloading a file from the tftp server to any user given file or uploading any file to the tftp server is supported only for specific type of files. Comware command allows . In ProVision this functionality is supported only for specific type of files. The destination file parameter is mandatory.

HP Switch# tftp 120.93.49.9 put config tftp_testTFTP download in progress.HP Switch# tftp 120.93.49.9 get config2 tftp_testHP Switch# tftp 120.93.49.9 sget test tftp_testEnter [email protected]'s password:Attempting username/password authentication...00000K

File transfer terminated by user request.


HP Switch# copy tftp flash 10.29.227.13 flashDevice will be rebooted, do you want to continue [y/n]?

Operating Notes





tftp ipv6 copy


3-34

Fundamental Commandsundo

undo

Used to reset the configuration of the system.

HP Switch# undo vlan vlan-id


HP Switch# no vlan vlan-id

Operating Notes





undo no vlan vlan-id


Index – 1

Index

A

aaa accounting commands … 3-6, 3-7accounting, show … 2-277alias, show … 2-9arp detection statistics, display … 2-4arp detection statistics, show … 2-4arp detection, display … 2-3arp ip-address, display … 2-5arp, display … 2-1arp, show … 2-1arp-protect, show … 2-3

B

backup startup-configuration … 3-1BGP … 2-105, 2-108boot set-default flash … 2-7boot system … 2-7boot-history, show … 2-340boot-loader, display … 2-6

C

CLI context levels … 1-4CLI prompts … 1-4clock datetime … 3-2clock summer-time one-off … 3-3clock summer-time repeating … 3-4clock timezone … 3-5clock, display … 2-8command accounting … 3-6command authorization … 3-7command-alias enable … 3-8command-alias mapping … 3-9command-alias, display … 2-9commands, listing … 1-4Comware software … 1-1

HPN switches … 1-1config, show … 2-291, 2-293context level … 1-4copy … 3-10counters rate, display … 2-15counters, display … 2-11cpu, show … 2-16

cpu-usage history, display … 2-17cpu-usage, display … 2-16crypto host-public-key, show … 2-274current-configuration by-linenum,

display … 2-19current-configuration configuration,

display … 2-20current-configuration interface, display … 2-21current-configuration, display … 2-18, 2-71

D

debug, show … 2-23debugging, display … 2-23default-configuration, display … 2-25delete … 3-11device, display … 2-26dhcp relay information all, display … 2-28dhcp relay information interface Vlan-interface

, display … 2-29dhcp relay statistics, display … 2-30dhcp-relay, show … 2-30dhcp-snooping binding database, display … 2-34dhcp-snooping binding, show … 2-36dhcp-snooping bindings, show … 2-106dhcp-snooping information, display … 2-35dhcp-snooping packet statistics, display … 2-37dhcp-snooping trust, display … 2-38dhcp-snooping, display … 2-36dhcp-snooping, show … 2-34, 2-38dhcpv6-relay, show … 2-117diagnostic-information, display … 2-40display command listing … 1-2dns domain dynamic, display … 2-41, 2-42dns ipv6 server, display … 2-45dns, display … 2-43documentation

latest versions … 1-xvrelease notes … 1-xv

domain name … 2-43dot1x sessions, display … 2-56dot1x statistics, display … 2-56dot1x, display … 2-47, 2-56


2 – Index

E

empty output … 1-5environment, display … 2-59erase config … 3-9, 3-11event log

Event Log Message Reference Guide … 1-xv

F

fan, display … 2-60field mappings … 1-3fields, not populated … 1-4fips status, display … 2-61flash, show … 2-6flow-control … 3-12

G

garp statistics interface , display … 2-62garp timer interface, display … 2-63gvrp state interface vlan , display … 2-64gvrp statistics, display … 2-66gvrp status, display … 2-67gvrp vlan-operation interface interface-type in-

terface-number, display … 2-69gvrp, show … 2-62, 2-63, 2-64, 2-66, 2-67

H

history, show … 2-70history-command, display … 2-70HP Networking

switch documentation … 1-xv

I

idle-timeout … 3-13igmp group interface vlan-interface static,

display … 2-77igmp group interface vlan-interface verbose,

display … 2-78igmp group interface vlan-interface,

display … 2-75igmp group port-info, display … 2-80igmp group static, display … 2-83igmp group verbose, display … 2-85igmp group x.x.x.x static, display … 2-86igmp group x.x.x.x verbose, display … 2-87

igmp group, display … 2-73igmp interface verbose, display … 2-91igmp interface vlan-interface , display … 2-93igmp interface, display … 2-88igmp routing table, display … 2-96int, show … 2-15interface brief down, display … 2-103interface brief, display … 2-100interface command … 2-67interface transceiver detail , show … 2-350, 2-353interface transceiver detail, show … 2-342, 2-347interface, display … 2-98interface, show … 2-11, 2-98interfaces brief, show … 2-100, 2-103ip

as-path, display … 2-105aspath-list, show … 2-105community-list, display … 2-108community-list, show … 2-108dns, show … 2-43igmp group, show … 2-73igmp groups, show … 2-73ospf interface, show … 2-201ospf virtual-link, show … 2-211ospf, show … 2-209

ip check source, display … 2-106ip client-public-key, show … 2-276ip dns, show … 2-45ip host-public-key, show … 2-274ip http, display … 2-109ip https, display … 2-110ip igmp vlan , show … 2-80, 2-83, 2-86, 2-88, 2-93,

2-96ip igmp vlan, show … 2-75ip ip-prefix, display … 2-111ip ospf link-state, show … 2-204ip ospf neighbor, show … 2-207ip ospf statistics, show … 2-198ip ospf, show … 2-213ip pim bsr, show … 2-242ip pim interface, show … 2-248, 2-250ip pim neighbor, show … 2-255, 2-257ip pim rpf-override, show … 2-195ip prefix-list, show … 2-111ip source-lockdown bindings, show … 2-355ip ssh, show … 2-310, 2-314, 2-316ip, show … 2-43ipv6 dhcp duid, display … 2-112


Index – 3

ipv6 dhcp relay server-address all … 2-113ipv6 dhcp relay server-address interface,

display … 2-115ipv6 dhcp relay statistics, display … 2-117ipv6 helper-address, show … 2-113, 2-115ipv6 mld vlan , show … 2-177, 2-183, 2-184, 2-187ipv6 mld vlan, show … 2-173, 2-174, 2-179, 2-181,

2-186ipv6 mld, show … 2-169ipv6 ospf3 interface, show … 2-221ipv6 ospf3 neighbor detail, show … 2-216ipv6 ospf3 neighbor detail, show … 2-234ipv6 ospf3 neighbor router-id, show … 2-230ipv6 ospf3 neighbor, show … 2-228ipv6 ospf3 statistics, show … 2-237ipv6 ospf3 virtual-link, show … 2-240ipv6 route, show … 2-120, 2-122, 2-124ipv6 routing-table ipv6-address, display … 2-122ipv6 routing-table protocol, display … 2-124ipv6 routing-table, display … 2-120

L

lacp local, show … 2-125lacp system-id, display … 2-125latest manual set … 1-5link, manual set … 1-5link-aggregation member-port, display … 2-128link-aggregation summary, display … 2-130link-aggregation verbose, display … 2-132link-aggregation, display … 2-127listing commands … 1-4lldp local-information global, display … 2-138lldp local-information interface interface-type

interface-number, display … 2-139lldp local-information, display … 2-135lldp neighbor-information brief, display … 2-141lldp neighbor-information list system-name,

display … 2-143lldp neighbor-information list, display … 2-143lldp statistics global, display … 2-146lldp statistics interface interface-type inter-

face-number, display … 2-147lldp statistics, display … 2-144lldp stats, show … 2-144, 2-146, 2-147lldp status interface interface-type interface

number, display … 2-150lldp status, display … 2-149

lldp tlv-config interface interface-type inter-

face-number, display … 2-151load-balancing … 2-127logfile buffer, display … 2-152logging, debug … 2-23logging, show … 2-152loopback-detection, display … 2-155

M

mac-address aging-time, display … 2-157mac-address multicast, display … 2-159mac-address, display … 2-156mac-address, show … 2-156mac-authentication, display … 2-160, 2-165Management Information Base

See MIB.manual set, link … 1-5memory, display … 2-167MIB

mld group interface vlan-interface verbose,

display … 2-174mld group interface vlan-interface,

display … 2-173mld group port-info, display … 2-176mld group verbose, display … 2-177mld group x.x.x.x verbose, display … 2-181mld group x.x.x.x, display … 2-179mld group, display … 2-169mld interface verbose, display … 2-184mld interface vlan-interface verbose,

display … 2-187mld interface vlan-interface, display … 2-186mld interface, display … 2-183mld routing-table, display … 2-189monitor-link group, display … 2-190multicast forwarding-table, display … 2-192Multicast Listener Discovery

See MLD.multicast routing-table static, display … 2-195multicast routing-table, display … 2-193multicast rpf-info, display … 2-197

O

osfp lsdb, display … 2-204ospf cumulative, display … 2-198ospf interface, display … 2-201


4 – Index

ospf peer, display … 2-207ospf routing, display … 2-209ospf vlink, display … 2-211ospfv3 area area-id peer peer-router-id,

display … 2-216ospfv3 area area-id peer verbose,

display … 2-219ospfv3 interface, display … 2-221ospfv3 lsdb statistics, display … 2-227ospfv3 lsdb, display … 2-225ospfv3 peer peer-router-id, display … 2-230ospfv3 peer statistics, display … 2-233ospfv3 peer verbose, display … 2-234ospfv3 peer, display … 2-228ospfv3 statistic, display … 2-237ospfv3 vlink, display … 2-240ospfv3, display … 2-213output differences … 1-3output, empty … 1-5

P

pim bsr-info, display … 2-242pim control-message counters, display … 2-246pim grafts, display … 2-247pim interface verbose, display … 2-250pim interface, display … 2-248pim join-prune, display … 2-254pim neighbor verbose, display … 2-257pim neighbor, display … 2-255pim routing-table, display … 2-260pim rp-info, display … 2-261poe device, display … 2-262poe interface power, display … 2-265poe interface, display … 2-263poe power-usage, display … 2-267poe-power alarm, display … 2-268poe-power switch state, display … 2-269port trunk, display … 2-270port trunking … 2-127port-access authenticator, show … 2-47port-access mac-based, show … 2-160power-over-ethernet brief, show … 2-262, 2-263,

2-265, 2-267prompts, CLI … 1-4protocol-vlan interface, display … 2-273protocol-vlan, display … 2-272ProVision Software … 1-1

ProVision software

Comware support … 1-1HPN switches … 1-1

public-key local rsa public, display … 2-274public-key peer, display … 2-276

Q

quit … 3-14

R

radius host, show … 2-277radius scheme, display … 2-277radius, show … 2-277reboot … 3-15reload … 2-7reload , show … 2-295reset saved-configuration … 3-16restore startup-configuration … 3-17return … 3-18rip process-id interface-type interface-number,

display … 2-284rip process-id ip-address mask/mask-length-

clock, display … 2-285rip process-id route peer ip-address,

display … 2-287rip process-id route, display … 2-286rip, display … 2-283rmon statistics, display … 2-288rmon statistics, show … 2-288route-policy, display … 2-289running-configuration, show … 2-18, 2-19, 2-21

S

save … 3-19saved-configuration by-linenum, display … 2-293saved-configuration, display … 2-291schedule reboot at … 3-20schedule reboot delay … 3-21schedule reboot, display … 2-295screen-length … 3-22secure-mode, show … 2-61set authentication password … 3-23sflow agent, show … 2-296sflow slot, show … 2-296sflow, display … 2-296


Index – 5

snmp-agent community, display … 2-298snmp-agent group, display … 2-299snmp-agent local-engineid, display … 2-302snmp-agent mib-view, display … 2-303, 2-304snmp-agent sys-info, display … 2-305snmp-agent trap-list, display … 2-306snmp-agent usm-user, display … 2-308snmp-server traps, show … 2-306snmpv3 community, show … 2-298snmpv3 engineid, show … 2-302snmpv3 group, show … 2-299, 2-303snmpv3 user, show … 2-308spanning-tree config, show … 2-327spanning-tree detail, show … 2-322, 2-324spanning-tree instance, show … 2-337spanning-tree mst-config, show … 2-335spanning-tree, show … 2-319, 2-332speed … 3-24ssh client source, display … 2-309ssh server session, display … 2-310ssh server status, display … 2-312ssh server-info, display … 2-311ssl client-policy, display … 2-314ssl server-policy, display … 2-316startup saved-configuration … 3-25startup, display … 2-318stp abnormal-port, display … 2-322stp bpdu-statistics, display … 2-324stp brief, display … 2-327stp down-port, display … 2-329stp history, display … 2-330stp instance tc slot … 2-334stp instance tc, display … 2-334stp instance, display … 2-327, 2-332stp interface GigabitEnterface, display … 2-327stp region-configuration, display … 2-335stp root, display … 2-337stp tc, display … 2-334stp, display … 2-319, 2-332sysname … 3-26system fans, show … 2-60system information, show … 2-157, 2-167, 2-305system power-supply, show … 2-268system temperature, show … 2-59system, show … 2-8system-failure, display … 2-340system-view … 3-27

T

Tab key … 1-4tacacs, show … 2-71tech, show … 2-40telnet … 3-28telnet ipv6 … 3-29telnet server enable … 3-30terminal type … 3-31tftp … 3-32tftp ipv6 … 3-33this, display … 2-341time … 2-8time, show … 2-8transceiver alarm interface, display … 2-342transceiver diagnosis interface, display … 2-347transceiver interface, display … 2-350transceiver manuinfo interface, display … 2-353trunking, port … 2-127trunks load-balance interface, show … 2-127

U

undo … 3-34uplink-failure-detection, show … 2-190user-bind, display … 2-355

V

vlan, display … 2-356vrrp interface vrid, display … 2-359vrrp statistics global, show … 2-362vrrp statistics interface vrid, display … 2-362vrrp statistics, display … 2-360vrrp statistics, show … 2-360vrrp verbose, display … 2-363vrrp vrid, show … 2-359vrrp, display … 2-357vrrp, show … 2-357, 2-363

W

warranty … 0-iii


Technology for better business outcomes

To learn more, visit www.hp.com/networking

© Copyright 2012 Hewlett-Packard Development Company, L.P.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP will not be liable for technical or editorial errors or omissions contained herein. September 2012

Manual Part Number 5998-3593


http://www.hp.com/networking

hp switch software - apache welcome pageh20628. · hp switch software hp 3500 hp 3800 hp 2910al hp...

Documents