home improvement guide - garden cities · thornwood architectural home improvement guide –...

THORNWOOD ARCHITECTURAL HOME IMPROVEMENT GUIDE – JANUARY 2019:

Page | 1

GARDEN CITIES

HOME IMPROVEMENT

GUIDE

for

Alterations and Additions

to

Homes

THORNWOOD HOME OWNERS ASSOCIATION


Page | 2

HOME IMPROVEMENT GUIDE TO HOMEOWNERS

JANUARY 2019

Updated July-2019

Index

Clause 1 Introduction

Clause 2 Architectural Language

Clause 3 Site Layout

Clause 4 Building Mass

Clause 5 Exterior Windows and Doors

Clause 6 Boundary Walls

Clause 7 Stonework

Clause 8 Basements

Clause 9 Balustrades

Clause 10 Awnings and Pergolas

Clause 11 Flat Roofed Improvements

Clause 12 Paint

Clause 13 Verge Paving

Clause 14 Swimming Pools

Clause 15 TV Antennae and Satellite Dishes

Clause 16 Burglar Bars

Clause 17 Water and Energy Saving Devices

Clause 18 Minor Works

Clause 19 Street numbers and Post Boxes

Clause 20 Safety

Clause 21 Plan Submission Procedure

Clause 22 Working Document

Clause 23 Miscellaneous

Annexures

“A” Boundary wall examples

“B” Steel Palisade Fencing – Privacy

“C” Examples of awnings and drop down blinds allowed and disallowed

“D” Non-permissible chimney’s and steel flues

“E” Burglar bars

“F” Plans submission procedure

“G” Planning submission fees


Page | 3

1. INTRODUCTION

1.1 Garden Cities is known to generations of homeowners for its enviable record of successful, integrated suburbs that

have generated a strong sense of civic responsibility and pride among their thousands of residents. The intention

of this guide is to assist the new homeowner in ensuring that any form of improvement made to their home will

add value to the architectural coherence of the built fabric of Sunningdale. The principle objective of this coherence

in architectural language, building materials and colours, is to ensure that all improvements, alterations and

additions to existing buildings and streetscapes contribute to the value of each individual home owner’s

investment on the one hand, and to mitigate the visual impact of the development as a whole, on the other. It is

therefore important to note that for the benefit of all homeowners, this document is and will be a living document,

and will be revised, amended and updated from time to time.

For the benefit of all homeowners, the rules and guides that may have been acceptable in the past may become

unacceptable in the future and precedent will not be found to be grounds for departures from the rules of the

day.

1.2 Garden Cities together with the relevant Home Owners Association shall appoint a Registered Professional

Architect as the Supervising Architect who, in conjunction with the trustees, will ensure that all that all standards

are maintained throughout the lifespan of the HOA.

1.3 As stated in agreement of sale documentation and HOA constitution rules.

“No alteration, addition, demolition, major decoration or reconstruction of or to the property, including walls,

fences and sidewalks, may be undertaken without the prior approval of the appointed Supervising Architect

and HOA trustees and the relevant local authority where applicable.”

1.4 For home improvement planning applications a refundable deposit will be collected; which will be refunded once

an inspection has been concluded to determine that the building has been constructed in accordance with the

approved building plans and that repair, if any, to the road, kerb and verge areas and HOA property have been

made good by the homeowner as a result of the construction. Major improvements will require an extra

inspection at roof height.

1.5 No application will be accepted without payment of the prescribed fees to the relevant supervising architect,

including penalty fees, if the work has been commenced or completed at the time of the application.

1.6 Each and every planning application will stand on its own merit and its own set of particular circumstances’.

Precedence shall not constitute a binding form of motivation.


Page | 4

1.7 Any additions, alterations, or amendments to the original approved HOA planning applications, at any stage, are

to be submitted to the supervising architect for further approval.

1.8 In questions of interpretation of the Guide or in the event of matters arising from the design process which are not

addressed by the Guide, the Trustees and supervising architect shall make a final and binding ruling. Minor

variations that are deemed to be in the interest of the built environment and compatible with the guide may be

considered by the supervising architect and/or the H.O.A .from time to time.

1.9 Clearance certificates required by the transferring attorneys upon the sale of a home, may be withheld by the

estate management should any improvement have taken place without obtaining planning approval, or the

property has not been maintained to acceptable standards.

1.10 The approval of any planning application does not absolve the homeowner from his/her responsibility of obtaining

local authority – City of Cape Town OOSTENBERG Administration – building plan approval. The HOA supervising

architect plans approval process is not to be construed in any way whatsoever as City of Cape Town plans approval.

1.11 No building work may commence until HOA and City of Cape Town plans approval has taken place. Should

deviations from the approved plans be required during the construction process, the entire application is to be

re-lodged for new HOA approval & City of Cape Town plans approval.

1.12 All building plans are to be prepared and submitted by professionals registered with the South African Council of

the Architectural profession. (SACAP)

2. ARCHITECTURAL LANGUAGE

This guide does not attempt to be excessively descriptive in terms of architectural style as such. It is more

concerned with the achievement of architectural synergy and cohesion with the existing streetscapes.

3. SITE LAYOUT

All properties should endeavour to further promote the philosophy of the “Garden City Ideal “with the planting of

trees and the theme of a flowing soft landscape, which penetrates between the buildings, complementing the

extensive public open spaces, by being properly maintained.

3.1 Immediately upon handover of the house keys, all existing trees along the immediate road frontage become the

full responsibility of the homeowner. Trees are to be regularly watered and cared for and are not to be removed

without prior written consent.

3.2 The road reserve between the roadway and front boundary of the home is the property of the local authority and

the relevant Homeowners Association (HOA) and as such requires their permission for alterations to same. The

planting of and use of stone chips is to be controlled by the appointed Supervising Architect. Planning approval is

required in this regard. A reasonably competent landscaping layout plan is to be provided with the application.

3.3 No home improvement may take place over a Servitude Area.


Page | 5

4. BUILDING MASS

4.1 The addition of extra garaging is permissible provided that the addition is set back, or a method of softening the

impact of the addition is set in place. For example, an added trellis/ pergola system in front of these garage doors

would suffice.

4.2 Granny flats are permitted, however; with the consent of the neighbourhood – the number of affected

homeowners’ consents are to be determined by the trustees and Supervising architect.

4.2.1 They shall be subject to the provisions of clause 1.8

4.2.2 An extra parking bay is to be provided on the property.

4.2.3 A guest bedroom sufficient in size to be deemed a flatlet shall be subject to the provision of an extra parking

bay.

4.2.4 Each granny flat application WILL be dealt with on its own merits.

4.2.5 The granny flat addition should tie in with the main dwelling so as to ensure that it does not impact negatively

on the overall architecture of the existing dwelling and surrounding houses.

4.2.6 Apart from the living room, the Granny flat is permitted one bedroom, one bathroom and one kitchen, a

study is permitted.

4.2.7 The gross square metres of the granny flat may not be more that 30% of the original main dwelling size which

includes the garage, if the garage is part of the house and not freestanding.

4.3 Double storey additions will require numerous neighbours’ consent, due to their impact upon the built

environment.

4.3.1 Every application shall be subject to the provisions of clause 1.8

4.3.2 It is recommended that any upper level addition to the ground floor of a Single Residential building, may not

be less than 75% of the total coverage of the original dwelling floor area. Every endeavour must be taken to ensure

that overlooking features are kept to the minimum, with special care taken to ensure that the core recreation areas

of neighbours’ homes are not overlooked.

4.3.3 Double Storey additions shall not be permitted to encroach over building lines.

5. EXTERIOR WINDOWS AND DOORS

5.1 All new windows are to match not only the existing dwelling, but also the adjoining dwellings and those in the

immediate area.

5.2 All new doors including garage doors, are to match the existing.


Page | 6

6. BOUNDARY WALLS

6.1 Street frontage boundary walling should, as far as possible, be maintained, as originally developed, by Garden

Cities. The City’s “BOUNDARY WALLS AND FENCES POLICY FINAL 2009” applies.

Homes that have their living space (recreation area) essentially on or about the roadway are permitted 1.8m

high walls on the street boundaries to afford privacy and security. In permitting these high walls on one side of

the street it is important that on the other side of the street, the street boundary walling takes the form of link

walling only. However, where security may be required by a homeowner, some form of cohesive security barrier

may be permitted but maintaining the wide openness or permeability of the streetscapes. Additional walling is

to be compliant with the City’s “BOUNDARY WALLS AND FENCES POLICY FINAL 2009”.

6.2 The accepted standard for all homes who may require security is a low wall with pillars and palisade panels infills.

This will provide a cohesive form of street frontage security walling throughout the Hillwood. This security barrier

along street boundaries may take the form of a the low “werf-muur” wall, 600mm in height with Steel

palisade infill panels 1200mm high to make up the overall 1800mm. The Palisade panels are to be placed

between 330x330mm plastered and painted masonry/brick columns which are to straddle the low wall

and to be at least 2,500m apart. All materials are to match the existing dwelling. (Please see ANNEXURE

“A” giving a few examples).

6.3 Existing Steel Palisade panels are a vital compliment of many streetscapes, creating a break between long tunnels

of street boundary walling. They are NOT permitted to be closed up by means of Nutec-fibre-cement panels, nor

latte, nor shade-cloth. Should a homeowner require privacy behind these panels, two methods of achieving this

are in place.

6.3.1 A solid screen may be erected at least 600mm behind the steel palisade fencing panel. This may either be a

plastered wall the same colour as the boundary screen wall, or natural stone cladded wall in sandstone or off-

white in colour. Access to closures are to remain open for maintenance purposes.

6.3.2 or a screen in some form complimented by live natural vegetation. (Please see ANNEXURE “B” giving a few

examples).

6.4 Sliding Steel palisade vehicular gates may be permitted when incorporated with clause 6.2 above.

6.5 LATERAL OR SIDE BOUNDARY.

6.5.1 COMMON BOUNDARIES: Smooth faced Vibracrete panels may be raised by 1 panel (7 panels total from

ground level or 2.100m). All Adjoining owners are to be notified. Rough faced Vibracrete panels are the

neighbours property. City of Cape Town planning approval is required for the raising of Vibracrete panels.

In exceptional cases where privacy is required, panels may be raised by 2 panel’s maximum (8 panels total

from ground level or 2.400m in height measured from the first panel on the ground). Adjoining owners’

consent is required. The City of Cape Town’s planning approval is required. Further, 2,400m high walls will

require a departure from the City’s “BOUNDARY WALLS AND FENCES POLICY FINAL 2009”. Full building

plans are required showing Site Plan, Ground Plan, Sections and Elevations. For 2,4m high walling all af-

fected neighbours are to sign the plans.


Page | 7

6.5.2 In order to respect the aesthetic harmony of all neighbouring boundary walling and street boundary wall.

All suchlike raised panels are to step down and ultimately taper (gently- chamfer) to the matching height of

the neighbouring wall.

7. STONE CLADDING

Only natural light in colour stonework will be considered, and would have to be made up of natural stone, cut and

dressed on site and installed by a specialist stonemason only. The Supervising Architect is required to inspect the

stonework at commencement, during and at completion.

8. BASEMENTS

Basements to comply with the National Building Regulations definition. (Ceiling at less than 1m above the average

immediate natural ground level)

9. BALUSTRADES

Balustrades must be designed simply and elegantly. They must compliment the style of the main building and

where applicable to match other suchlike in the immediate vicinity.

10. AWNINGS AND PERGOLAS

10.1 Planning approval is required for any form of fixed Pergola or awning.

10.2 Only plain Awnings are permitted and are to be the same colour as the house. The use of external drop-down

blinds on Patios is discouraged. They may be permissible, only where completely out of street and/or open space

view. They are to be dropped down only during adverse weather and at night, if required. They may not be set in

place permanently. They may not be striped. They are to be a light sand color or a lighter shade of the house color.

A minor works planning application is required for their approval. (Please see ANNEXURE “C” giving an examples).

10.3 Solariums – sun rooms are not permitted.

11. FLAT ROOFED IMPROVEMENTS: COVERED VERANDAHS, BRAAI TERRACES, BRAAI ROOMS, CARPORTS.

11.1 The maximum amount of flat roofed areas on a property may only be 30% of the original dwelling floor area and

the maximum roof span over a flat roofed area may not be greater than 3,8m. Each application is to be assessed

on its own architectural merit. “Shade and shelter” requirements over a Patio in the form of a lean-to roof

(afdakkie) require special attention. Where a bedrooms’ natural ventilation is impacted upon, mechanical venti-

lation needs to be installed. This shade and shelter lean-to roofed areas are not to be converted into rooms by

means of sliding doors or windows. Stacker/Fold away doors may be fitted to the open end of a Covered Patio,

provided the Patio is encapsulated by the home on three sides. These doors are not to be permanently closed

but are to be used at night and during adverse weather. Their permanent closure will impact negatively upon

the built environment architecture.


Page | 8

11.2 Roofing is to be of one roofing material only. A patchwork of translucent and other material is not permitted.

Small profile corrugated steel roofing is to be used. (The industrial type of IBR profile roofing sheets are not

permitted)

11.3 New covered area supports must either be in timber/steel sections, square and at least 75x75mm in size.

11.4 Only the Louvre type prefabricated Aluminium awnings are permitted.

11.5 For the installation of Stack-away fold-up doors to covered Patios; HOA conditions of approval for these doors are

such that as their name suggests, they are to be stacked away. However, they may be used during adverse

weather and at night for security. (Often, with them in place, the natural ventilation to bedrooms is cut off and

this is not only unhealthy but is also contravening National Building Regulations). A further HOA condition of

approval for these doors, is that they are not to have any window sections implanted into them. This form of

HOA planning application requires a full building plans submission, and inspection not only to the HOA but also

to the City of Cape Town.

11.6 Carports must have a horizontal roof, with sloping roofing sheets hidden behind a solid Nutec fibre cement fascia

or solid (not slatted) aluminum fascia’s. Carport roofing is to be of one roofing material only. A patchwork of

translucent and other material is not permitted. Carport roof supports are to be of square timber/steel posts

placed upon 330x330x600mm high plastered brick piers.

11.7 Shade ports are not permissible.

12. NEW ROOM ADDITIONS

12.1 Formal room additions eg. Bedroom, Family Room, Braai-room etc., are to be constructed

under a pitched roof, of the same type as the main house. Small short portions of home additions,

where pitched roofs are not possible, may be flat roofed. Where Industrial IBR longspan steel roofing

sheets are incorporated into small short portions of flat roofs, these sheets are to be screened by par-

apet walling.

13. PAINT AND NEW BUILDING WORK COLOURS

12.1 All new paint and finishes are to match the existing dwelling.

12.2 All new steelwork is to match the steelwork on the existing dwelling.

14. VERGE PAVING

All paving visible from the street and on road reserve ground levels, must be in keeping with other paving in the

immediate area. Minor works planning approval is required for any new paving or landscaping within the road

reserve, this being the verge area, between roadway and property boundary line.


Page | 9

15. SWIMMING POOLS

15.1 The installation of a swimming pools requires a full planning approval. Applications including plans are to be

lodged with the supervising architect together with the pool suppliers’/manufacturers’ details.

15.2 Pumps and filtration systems are to be indicated on the plan and are to be located so as not to cause a disturbance

to neighbours. (a min of 1,5m from common boundaries). They should not be visible from the road or adjacent

open spaces.

15.3 Pool enclosures (safety fencing) must comply with National building regulations SABS 10400 and be of simple

design to match the dwelling and not exceeding 1.2m in height.

15.4 The backwash is to discharge into the dwellings sewer system.

15.5 The developer will not be held accountable for any underground services which may transverse the swimming

pool situation.

16. TV ANTENNAE - SATELLITE DISHES AND CHIMNEYS

16.1 Aerials and satellite dishes should be obscured within the roof space or otherwise concealed where possible.

Dishes are to be placed away from roads. No suppliers’ advertising is to be affixed to satellite dishes.

16.2 Fire appliances; New free standing fire appliances may be installed. The positioning of steel flues would be

preferred on the far side of the roof ridge line, away from the roadway. They are to be properly maintained to

prevent rust streaks staining the roof. The minimum and maximum height above the roof tile is to be 1 metre.

If located on or close to the ridgeline, 600mm minimum & maximum above same ridgeline. (Please see

ANNEXURE “D” for typical non-permissible chimney’s and steel flues)

17. BURGLAR BARS AND SECURITY GATES

17.1 Burglar bars should be simple horizontal lines, without ornate detail. (Please see ANNEXURE “E” Burglar bars)

17.2 External “basket type” steel burglar bars are not permitted.

18. WATER AND ENERGY SAVING DEVICES

18.1 Environment aesthetics take precedence over all unsightly installations. All neighbourhood homeowners are to

consent.

18.2 The use of water saving devices and technologies is encouraged with all home improvements. See Annexure “G”

for permissible solar water heaters. Only flat and not tubular panels are permitted with the minimum of exposed

piping. Exposed piping is to be the same colour as its background colour- example house paint colour or concrete

roof tile colour.


Page | 10

18.3 Gardens and irrigation systems are to be designed according to best practices for water conservation.

Rainwater harvesting tanks (Jo-Jo tanks) are to be kept out of sight of roadways and public open spaces.

Where aesthetically affected, neighbours are to consent to their positions. Horizontally or obliquely fitted

long lengths of roof rainwater downpipes discharging into water harvesting tanks are not acceptable.

Only vertically discharging lengths of roof rainwater downpipes into water harvesting tanks are

permitted.

18.4 The roadway verge between the roadway and house street boundary remains the property of the HOA. Minor

works planning approval is required for any development of verges. (Please see clause 19.3.2 below)

18.5 All other energy saving devices; whether wind turbines, rain-storage tanks, etc. requires approval in terms of sizing

and placement prior to proceeding with such projects. Fully detailed plans, specifications and fixing/installation

details will be required. Minor/major works planning applications are required. The roof solar water heater with

cylinder type is not permitted.

19. DEEMED MINOR WORKS

19.1 Clause 1.10 of the guide is applicable to all Minor works applications as well.

19.2 Minor works applications are to take the following format;

19.2.1 Full contact details of the applicant/home-owner are required including email address.

19.2.2 The home-owners' house plan, including the site, captured on an A4 or A3 sheet is to be

emailed to the supervising architect for minor works planning approval.

19.2.3 A reduced application fee, currently of R 309.00 (excluding VAT) is payable.

19.2.4 No building refundable deposit is required.

19.3 Minor works are categorized as the following;

19.3.1 The installation of electric fencing is permitted with the consent of all affected adjoining owners. The

maximum amounts of strands are to be 6 (six) strands). Once an electric fencing planning approval has been

granted the raising of vibracrete panels will require the re-approval and re-consent of the electric fencing by all

affected adjoining homeowners. The making good of the reverse side of the newly raised panels should they

require painting to match the existing, should be for the account of the homeowner making application for the

extra panels.

19.3.2 The development of the street frontage verges are to be submitted to the HOA supervising Architect for

approval as a minor works planning application.

19.3.3 The installation of air conditioning units is not a minor works application, but they are to be installed

below boundary screen walls.

19.3.4 Free-standing Wendy house sheds are permitted only if not visible from any streets or open spaces. Their

roofs are to be the same colour as the main house. All affected adjoining owners' consent will be required

where the common building lines are encroached upon.

19.3.5 The installation of retractable awnings and/or roll down vertical blinds. (Full specifications are required.)

19.3.6 For overly large structures including overly large Jungle Gyms and Garden type furniture. (Full specifica-

tions are required, Size, Height, finishes and site situation.)

19.3.7 Water & energy saving devices and technologies. No roof storage cylinder type solar water heaters are

permitted. (Please see Annexure “G”)

19.3.8 Any other minor works as so deemed at their time of application.

19.4 All minor works, as set out in 19.2 above, whichever applicable, are to be depicted on A4 or A3 size drawing

sheets.


Page | 11

19.5 Air conditioning condenser units are to be well concealed and not visible from roadways and/or or open spaces

and are to be installed at natural ground level or well below boundary screen walls. As with swimming pool

pumps, Air conditioning units are to be sited so as not to cause a disturbance to neighbours.

19.6 All sewer/plumbing pipes are to be concealed and are not to be visible on external walls.

20. STREET NUMBERS

All street numbers and postboxes are to remain as originally developed and when replaced are to comply fully

with the general type in the area.

21. SAFETY.

All areas under development that are seen to be building sites, demarcated or not, are deemed to be out of

bounds to all residents. Homeowners are to report any transgressions of these rules to the estate managementr.

21. PLAN SUBMISSION PROCEDURE

21.1 All applications may to be submitted by email to the appointed HOA Supervising Architect:

Reg Whittaker Architect I tel. 021-975 9083 I cell. 083 309 3024 I Fax. 086 672 9434 I email. [email protected]

21.2 All homeowners’ contact details, including email address, are to be made available with the application. (In this

regard an HOA planning application form can be found at the bottom of this document).

21.3 Plan applications not bearing the HOA stamp of approval, will not be accepted by the City of Cape Town.

21.4 Please see ANNEXURE “F” for a detailed planning submissions procedure.

21.5 Please ANNEXURE “H” for planning application submission fees and building refundable deposits.

21.6 Where building works deviate from the approved plans a “Stop-works” order may be executed where neces-

sary.

21.7 For minor works plan submission procedure, please see clause 18.

21.8 No planning applications will be considered until registration of the property has taken place

22. WORKING DOCUMENT

22.1 This document is a work in progress document and will be updated from time to time. The latest update guide is

available at the sales office or obtainable from the appointed Supervising Architect.

23. MISCELLANEOUS

23.1 Street (verge) trees are not to be removed without the prior consent of the HOA and/or its representatives.


Page | 12

Annexure “A” – Boundary Wall examples


Page | 13

Annexure “B” Steel Palisade Fencing -Privacy


Page | 14

Annexure “C” Examples of awnings and drop down blinds allowed and not allowed


Page | 15

Annexure “D” Non-permissible chimney/Steel flues


Page | 16

Annexure “E” – Burglar Bars

From a design point of view light pattern burglar guards as shown below are preferred

However, the "trellidoor " type option will be allowed All bars must be white in colour and installed as unobtrusively as possible.


Page | 17

Annexure “F”


Page | 18

ANNEXURE “G” Current Plan Submission Fees & Refundable building deposits

Item Amount

(Excl.

VAT)

Amount

(Incl.

VAT)

Additional Information

Scrutiny and Approval of Building Plans

Minor works scrutiny of A4-A3 sheets

R 536.00

R 309.00

R 616.40

R355.35

Written approval issued with comments where required.

Written approval issued with comments where required.

Per Site Inspection and Issuing of Comple-

tion Certificate

Per site inspection – “Minors works”

R 536.00

Zero

R 616.40

Zero

Issuing of Completion Certificate to facilitate return of

Builder’s Refundable deposit.

No site inspection for “Minor works”

Applicants refundable deposit – “Minor

works:”

Applicants refundable deposit – All other

works:

Zero

R 2 500.00

Zero

Zero

For all structural building work.

• Refundable deposits to be withheld if deviations are made from the approved plan.

• Refundable deposits to be withheld to offset damages to common property not repaired; where applicable.

Refundable deposit to be forfeited if the planning application is not completed within 18 months from the date of com-mencement of the building work.

• Please be advised that the Local Authority charges a separate plan scrutiny fee for City planning approval. • Refundable deposits to be refunded subject to the conditions above.

The Planning application fee shall increase to R 1 250.00 (ex.vat) should construction work have already commenced or

have been completed at the time of the application.

NOTE: ON COMPLETION OF YOUR PLANNING APPLICATION, THE SUPERVISING MUST BE CONTACTED TO EXECUTE A FINAL SITE INSPECTION. HE WILL ISSUE A COMPLETION CERTIFICATE AND YOUR RE-FUNDABLE DEPOSIT WILL BE REFUNDED.

YOUR CURRENT APPOINTED SUPERVISING ARCHITECT IS;

PO BOX 5293 TYGERVALLEY 7536

TIEKIEDRAAI 8 VIERLANDEN DURBANVILLE 7550

TELEPHONE 021 975 9083 FACIMILE 086 672 9434

TELEPHONE MOBILE 083 309 3024 EMAIL [email protected]

[email protected]

WEB www.regwhittakerarchitect.co.za

SACAP-PrArch.Reg.No.6572


Page | 19

:HOME IMPROVEMENT PLANNING APPLICATION FORM:

1.1.1.1. HOMEOWNER DETAILS

2.2.2.2. DETAILED SCOPE OF WORKS: (to be completed by Appointed Architectural Professional)

……………………………………………………………………………………………………………………… ……………………………………………………………………………………………………………………… ……………………………………………………………………………………………………………………… ………………………………………………………………………………………………………………………

3.3.3.3. PROPERTY OWNERS SIGNATURE:

………………………………………………………………………………………………………………………

The approval of any HOA planning application by this Supervising Architect does not absolve the homeowner from his/her responsibility to obtain City of Cape Town building plan approval. The HOA/Supervising Architect

“Plans-approval-process” is not to be construed in any way whatsoever as City of Cape Town or SANS/Building regulations’ planning approval. The HOA approval of this planning application is based entirely upon the merit

of acceptable aesthetics and the reasonable compliance with HOA Architectural Guide manual. Copyright REG WHITTAKER ARCHITECT SACAP Reg.No.6572. www.regwhittakerarchitect.co.za

ERF NO………………………………………………

NAME ........................................................................................................... (PROPERTY OWNER)

CELL NUMBER .............................................................................................. (PROPERTY OWNER)

STREET ADDRESS OF PROPERTY.…..………………………………………………………………………

EMAIL ADDRESS .......................................................................................... (PROPERTY OWNER)

4. DATE SUBMITTED

home improvement guide - garden cities · thornwood architectural home improvement guide –...

Documents