Mounting the AP on a wall安装AP到墙面

Log in to the AP from the Web interface 通过Web界面登录设备

Make sure the AP side with security slot is a minimum of 20cm (7.87 in) away from the wall corner.

在选择AP的安装位置时，请注意AP带防盗锁孔的一侧与墙壁拐角处之间至少要预留20cm的距离。

The AP is typically installed on a high position. As a best practice, access and configure the AP before installation. 由于设备一般都安装在较高的位置上，所以建议用户在把设备安装到指定位置之前先登录设备并进行相关配置。 To restore the AP to the factory default state, press and hold the Reset button for five seconds.当设备需要恢复到出厂设置时，可以按Reset键5秒可以恢复出厂设置。 Only fat APs support login through Telnet or Web.仅在FAT模式下支持此功能。

Make the installation hole locations on the wall for the wall bracket. Drill holes at the marked locations.Hammer wall anchors into the holes.

在墙面使用记号笔标记出安装件安装孔的位置，使用电钻在标记处钻孔并将膨胀螺管使用橡胶锤钉入安装孔。

Align the AP with the wall bracket in the direction as shown in the figure,and rotate the AP clockwise until it clicks into place.

将AP按照如上图所示的方向对准墙面的壁挂安装件，然后顺时针旋转至竖直位置，当听到“啪”的一声时，说明AP已经锁紧，安装完毕。

缺省情况下，Web功能已开启，并且设置了登录信息，用户可以直接使用以下信息登录设备：

By default, you can log in to the AP by using the following information:

Username: admin. Password: h3capadmin. Management IP address 192.168.0.50 and subnet mask 255.255.255.0 for VLAN-interface 1.

If you cannot use the default IP address to log in to the AP, contact the administrator for the most recent configuration.

用户名：admin 密码：h3capadmin 设备Vlan-interface1接口的管理IP地址：192.168.0.50，子网掩码255.255.255.0。

如果缺省的IP地址已被修改，请联系您的网络管理员获取最新配置。BOM：3104A0Y3

无线接入点 快速安装指南-6PW107Access Point Installation Quick Start-6PW107

WAP722E

Configuring wireless services无线服务配置

Only fat APs support login through Telnet or Web.

仅在FAT模式下支持此功能。

From the navigation pane, select Wireless Service > Access Service. On the page that opens, click Add. Enter a wireless service name, for example, test, and select crypto as the wireless service type.选择“无线服务”>“接入服务”>“新建”。“服务名称”为test，“服务类型”为crypto。

Retain the default basic wireless settings.保持无线服务的基本配置不变：

Extend the Security Setup list. Select Open-System as the authentication type, AES and TKIP as the cipher suite, and WPA and WPA2 as the security IE.

Extend the Port Security list. Select psk as the port mode, configure a pass-phase preshared key, and then click Apply.

展开“安全设置”，“认证方式”选中open-system，勾选“加密类型”、下拉菜单选择AES，“安全IE”选择WPA2。展开“端口安全”，勾选“端口设置”，“端口模式”选择PSK，PSK预共享密钥选择pass-phrase，填入密码后点击确定。

Select the wireless service and click Enable to enable the wireless service.

开启无线服务。

Click the Bind icon from the Operation field to bind the wireless template to an AP radio.

绑定无线服务到AP射频接口。

Save the configuration in either of the following ways:

Click Save at the top right corner of the page.

From the navigation pane, select Device > Configuration. Click the Save tab and then click Save Current Settings.

可以点击页面右上角的“保存”按钮保存配置，也可以点击“设备”>“配置管理”>“保存配置”的“保存当前配置”保存。

Copyright © 2018, New H3C Technologies Co., Ltd.

The information in this document is subject to change without notice.

Copyright © 2018 新华三技术有限公司 版权所有，保留一切权利

本文档中的信息如有更改，恕不另行通知

如需了解产品及安装方面的更多信息，请登录H3C网站 www.h3c.com