guidelines for project report writing mechanical

8/9/2019 Guidelines for Project Report Writing Mechanical

1/3

Note: Please find attached the guidelines for preparation of project report. A samplecontent sheet is also included for your easy reference. All students are requested to follow the

guidelines while preparing their project report.

All students are requested to submit a hard draft copy to their respective internal guidesfor their review and comments. The final printout of the project work should be under taken

only after review by their concerned internal guide. The internal guides are also requested to

review the report technically and also from the view point of the guide lines. Thereafter the final

version shall be submitted to the Head, !"H for comments # clearance # approval. $ailure toget the report approved by the internal guide # Head of the %ept or not following the guide lines

for preparation of the report may lead to rejection of the report.

inimum pages to be prepared for ini Project& '(

inimum pages to be prepared for ajor Project& )(

Three *+ copies *e-cluding your personal copy of the project report shall be submittedalong with the following&

. "% containing the total soft copy of the project report.

/. "% containing the program *source code 0 e-e file, input files, output files, compiler

etc.+. Hard soft *printout of the entire program along with input 0 output files.

1. Hard copy of all reference papers 0 material.

All the students are requested to go through their reports thoroughly before giving the same for photo2copying and binding so as to avoid re2binding.

Head, MECH


2/3

Guide Lines for Preparation of Project Report of B.Tech – MECH

i!e and No. of copies:

The dissertation should be submitted in A1 si3e, "ond paper. Three *+ copies of project reportshould be submitted. 4n addition to three copies, each student should also have individual copy.

Paper, T#pin$, for%at:

E&ecuti'e Bond paper should be used for preparation of the project report.

Typing should be done in / font of Times 5ew 6oman.

The layout should provide 1 cm of the left, +cm of the top 0 bottom and .' cm on the right. A

double line margin can be used on the four sides of the page as margin.

$resh paragraph should commence after three spaces. 7 spacing should be provided throughout the project report. Page 5umbers shall be indicated at the "otto% %idd(e of the each pa$e.E'er# pa$e shou(d "e ri$ht justified.

Nu%"erin$ of )i$ures * Ta"(es:

The figures in a chapter may be serially numbered as $ig & ., $ig & ./,8.. 9here first digitindicates the chapter number and second digit indicates the figure number.

The numbering of tables should be similar to figures, such as Tab ., Tab ./ and so on.

Graphs:

The graphs, if any, should clearly indicate the points used for drawing the curve *s. The

numbering of graphs should be similar to fig such as :raph ., :raph ./ and so on

Nu%"erin$ of references:

All references shall be serially numbered in the same order as they appeared in the report insquare brackets.

pe(( chec+in$:

The document should be completely spell checked.

;ample content sheet is also enclosed.

Note:

All the Table 5os., $igure 5os., graphs 5os., 6eferences, Appendices etc., referred in the body

of the te-t shall be made "o(d for easy reference. !-ample& The details shown in Ta"(e No: .- can be e-plained with help of the )i$ure No: . and as given in /01 and reproduced in

2ppendi&340.

;imilarly for equations

E'er# pa$e shou(d ha'e a header indicatin$ the tit(e of the project on the (eft top corner,

aurora e%"(e% on the ri$ht top corner and footer 5ith 2TR23B.Tech 6 MECH7 on the

(eft "otto% corner, depart%ent of MECH on the ri$ht "otto% corner

/


3/3

G89EL9NE );R PR;ear Project 6eport.

9. Co'er Pa$e 6;ee Proforma7

99. Report Contents

. %eclaration =y The "andidate

/. "ertificate signed by the :uide and H?% *;!! P6?$?6A

+. Acknowledgement *up to ain 6eport use roman number as page number&

*i, ii, iii8

1. Abstract

'. @ist ?f $igures

. @ist ?f Tables

'. "ontent with page numbers.

. ain 6eport

+

guidelines for project report writing mechanical

Documents