Department of Electrical Engineering SSTC, SSGI, Bhilai Page 1

Guidelines for Pre-thesis / Final Thesis Report writing

M. Tech. (Power System Engineering)

Contents of Project report

The Project Report should contain the items as outlined below and is to be presented in

the order as listed.

Number of Copies to be submitted to the Department

Number of group members plus three copies (for pre-thesis) & five (for final thesis)

has to be prepared. Hard copy of the report is to be submitted to the Department after

corrections done as suggested by guide/Department at any time when report submission

is called by guide/Department.

Requirements for Report Writing

Your report should meet following standards:

Font Name: Times New Roman(for normal text)

Font Size: 12 pt (for body of text)

Left Margin: 1.5 inch

Right Margin: 1.25 inch

Top Margin: 1.25 inch

Bottom Margin: 1.25 inch

Line Spacing: 1.5

Paragraph Spacing: 18 pt

1. Follow following standard for headings

Font Size:

Chapter title 16 pt (Bold) title case

Heading e.g. 1.1 14 pt(Bold) title case

Subtitle e.g. 1.1.1 12 pt (Bold) title case

Subtitle e.g. 1.1.1.1 12 pt (Bold) title case

2. There should be uniformity in writing headings and sub-headings in all chapters.

3. Avoid underlines and colon i.e. :

4. To indicate a figure, write below the figure and the format should be Fig. 1.5.

5. To indicate a table, write above the table and the format should be Table 1.5.

6. All the figure captions and table captions should be 12 size, bold and title case.

7. Figures used in the report should not be blur.Candidate should try to draw

the figures on their own.

8. All the figures and tables should be mentioned/referred/explained in the

adjoining paragraphs.

9. Always number the equations, tables and figures chapter wise, for e.g. 4lh

figure in

chapter 5 will bear the number Fig.5.4.

Department of Electrical Engineering SSTC, SSGI, Bhilai Page 2

10. Equations should be written compulsorily using MathType equation editor.

11. Never write report in first person i.e. "I will do this". Instead write author....

12. In Literature survey, do not give full mention of the paper. Instead write like this:

Gambhir el al. in [1] have discussed/concluded/suggestcd/rcported. Here [1] is

the number of the paper mentioned in References and Bibliography.

13. In References and Bibliography, the mention of paper should be

[11] Chatterji S. (the names of all authors), "Title", Journal or proceedings of

the conference, Vol.5, Issue/No.2, pp 365-370. month, year of publication.

Journal Article

[1] S.K. Ken ue and J.F. Green leaf, "Limited angle multifrequency diffraction

tomography," IEEE Trans. Sonics Ultrason., vol. SU-29, no. 6, pp. 213-217, July

1982.

Conference Article

[2] R. Finkel, R. Taylor, R. Italics, R. Paul, and J. Feldman, "An overview of AL

programming system for automation," in Proc. Fourth Int. Joint Con/ Artif. Intel/.,

pp., 758-765, Sept. 3-7, 1975.

12. All the mentioned references should be cited in the report compulsorily.

13. The sequence of chapters should be like this

Chapter 1 Introduction

1.1 Background & Motivation

1.2 Objective

1.3 Delimitation of research

1.4 Benefits of research

Chapter 2 Literature Survey

2.1 Literature Review

2.2 Inferences Drawn from Literature Review

Chapter 3 Problem Formulation and Proposed Work

3.1 Introduction

3.2 Problem Statement

3.3 Definition of problem statement terms

3.4 Proposed Work

3.5 Conclusion

Chapter 4 Methodology

4.1 Introduction

4.2 Implementation Strategy (Flowchart, Algorithm etc.)

4.3 Tools/Hardware/Software to be used

4.4 Expected Outcome (Performance metrics with details)

Department of Electrical Engineering SSTC, SSGI, Bhilai Page 3

4.5 Conclusion

Chapter 5 Result & Discussion

Chapter 6 Conclusion & Future Scope

14. After introductory chapter & literature survey, each chapter should have an introduction

& conclusion.

Introduction should consist of brief detail of the jist of current chapter & should

link with the previous chapter

Conclusion will consist of an overview of the heads covered in current chapter &

how it will lead to next chapter.

ARRANGEMENT OF CONTENTS:

The sequence in which the project report material should be arranged and bound should be

as follows:

1. Title Page (Glazed paper)

2. Declaration

3. Certificate from supervisor

4. Certificate by the examiner

5. Acknowledgment

6. Abstract

7. Table of Contents

8. List of Figures (if any)

9. List of Tables (if any)

10. List of Symbols (if any)

11. Abbreviations (if any)

12. Chapters

13. References

14. Appendices

BINDING SPECIFICATIONS:

Reports are to be Spiral bound ( Pre-thesis) & bound in BLACK colored hard cover (Final

Thesis) and golden print (engrossed) with written materials in black script on the title page

of the report. Number of pages should be minimum 40 ( for Pre-Thesis ) & should be

minimum 60 ( for Final Thesis ).