grafting machine & growing channels
TRANSCRIPT
The InjerStar robotfeatures modern, innovative technology for maximum productivity:
INJERSTAR
1 2
3
3 seconds per cycle.1 operator.Minimum maintenance cost.
Easy installation: InjerStar is light and compact so it may be transported easily and
conveniently and does not require installation operations. It is supplied in a block, which
means it can be moved at no cost and occupies the minimum possible space.
Maintenance: the InjerStar machine is not only efficient and reliable, but also
requires minimum maintenance to remain 100% productive. The machine is
supplied with a kit of replacement parts for normal wear on items such as
the blades.
Operation: the InjerStar machine is highly adaptable given that
operator involvement in machine operation is minimal. Human inter-
vention is only necessary to load the plant as all other operations,
including the attachment of a silicone clip on the grafting joint, are
performed quickly and simply.
Technical features: pneumatic machine combined with electronics and
robotics, with incorporated blade disinfection. The silicone clip is supplied by means
of roll feed.
The machine cycle lasts 3 seconds.
Grafting machineGrafting machine
Reel of grafting clips. 2- Training clips.
3- Courgette training clips.
1- Trainingof nursery seedlings.
32
Increased production. Savings in water and fertiliser, system of reuse.Compliance with applicableenvironmental regulations.100% recyclable.Long durability.Adaptability of the system: easy assembly and transport.
The “Growing Channel” comprises a plastic duct in
which different growth substrates for plant produc-
tion may be placed. It is also 100% recyclable.
This system may be used for:
Growing channel with substrate.
Hydroponic growing channel.
The channel’s compact dimensions make it suitable
for use anywhere and units may be connected to
one another to form a continuous growing channel.
This perfect adaptability makes it easy to transport
and assemble.
It can boost crop production considerably and is
therefore very competitively priced.
Hydroponic growing channelHydroponic growing channel
Increases return on production and yields savings in water
and fertiliser, which can meanwhile be recovered for proces-
sing and treatment.
Because of society’s increasing concern for environmental
deterioration, open systems are being adapted to new requi-
rements, thus prompting the collection and accumulation of
surplus water for recycling and subsequent use.
In nutrient solution circulation systems, great water and even
greater fertiliser savings can be obtained, plus a virtually
total reduction of environmental pollution. Experimental
tests indeed show that the use of these systems can yield
reduced water consumption.
Specially designed channelfor hydroponic growth.
Hydroponic channel section
Interior tray
Entrance and end cover
54
STAND designed specifically for assembling sections
of channel along the plot. It is highly versatile as it
may be buried or supported on legs at the required
height.
It may also be HUNG using a chain or cable, thread
through the holes in the clamps. Two-level produc-
tion is therefore possible.
1 - Growing channel for substrate bags.
2 - Growing channel for loose or hydroponic substrate.
Growing channel with substrateGrowing channel with substrate
Coir is a substrate and may be used for soilless crops
or as a substitute for or component in other
substrates. The properties of this substrate last for
many years and a small quantity of new substrate
simply needs to be added every three years to
renew it.
The planting pattern and greenhouse climate
control management is similar to other substrates.
Growing table with channel
1 2
Growing table with channel. Very light and easily moved.
Made in 100% recyclable and non-deteriorating plastic.
With UVI protection and design patent.
The channel may be combined with a Closed Irrigation Circuit
(tank +pump+programmer) to facilitate watering.
The channel has an Outer Cover to protect the crop from pests or
weed growth.
The channel may also be used as a balcony garden.
It comes in two sizes:
Table for tall crops such as tomatoes, cucumbers and
courgettes, etc.
Standard table for crops such as aromatic herbs, lettu-
ces, strawberries, and escaroles, etc.
Standard sizes:
Height 55 cm or 80 cm
x Width 163 cm or 115 cm.
Depth 55 cm.
* Possibility of other measures.
This channel is alsoused for cultivation using peat, coir, and perlite, etc.
76
Tecus Plásticos began operating in 1997, with a view to capitalising on the
knowledge of its management, technical and production team, which has a
professional track record of over 30 years in the plastic part injection industry.
In accordance with our development and growth policy, we have extended our
installed and production capacity at our model plant and can therefore offer a
broad range of high-quality products and competitiveness to cover all needs.
We also have state-of-the-art technology for the development of our own
moulds.
Pol. Ind. La Llanac/ Pont de Can Claverí, 58 08191 RUBÍ - Barcelona
Tel. +34 93 588 62 36
E-mail: [email protected]