genuine satellite radio kit - trademotion€¦ · genuine satellite radio kit installation...

27
MAZDA CX-51 GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the contents of this booklet in order to properly install and use the satellite radio kit. Your safety depends on it. Keep these instructions with your vehicle records for future reference. There are several WARNING and CAUTION sections in this booklet concerning safety when installing. Always read and follow them in order to prevent injuries, accidents, and possible damage to the vehicle. WARNING: Indicates a situation in which serious injury or death could result if the warning is ignored. CAUTION: Indicates a situation in which bodily injury or damage to the vehicle could result if the caution is ignored. If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation. If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before using it. Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property that arise from the failure of the dealer or installer to follow these instructions. To ensure safety and reliability of the work, installation, removal and disposal work done by an Authorized Mazda Dealership is recommended. Be careful not to lose removed parts, and be sure that they are kept free from scratches, grease or other dirt. PART NAME: SATELLITE RADIO KIT PART NUMBER: KF69 V6 029 (Harness Kit P) VEHICLE: MAZDA CX-5 1ED6P11A24100 To the dealer Please turn over these instructions to the customer after installation. To the customer Keep these instructions after installation. The instructions may be necessary for installing other optional parts or removal of this accessory. Should the vehicle or this accessory be resold, always leave these instructions with it for the next owner. Note WARNING GB F

Upload: others

Post on 17-Apr-2020

17 views

Category:

Documents


1 download

TRANSCRIPT

Page 1: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-1

GENUINE SATELLITE RADIO KIT

INSTALLATION INSTRUCTIONS

Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the contents of this booklet in order to properly install and use the satellite radio kit. Your safety depends on it. Keep these instructions with your vehicle records for future reference.

• There are several WARNING and CAUTION sections in this booklet concerning safety when installing. Always read and follow them in order to prevent injuries, accidents, and possible damage to the vehicle.

WARNING: Indicates a situation in which serious injury or death could result if the warning is ignored.

CAUTION: Indicates a situation in which bodily injury or damage to the vehicle could result if the caution is ignored.

• If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation.

• If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before using it.

• Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property that arise from the failure of the dealer or installer to follow these instructions.

• To ensure safety and reliability of the work, installation, removal and disposal work done by an Authorized Mazda Dealership is recommended.

• Be careful not to lose removed parts, and be sure that they are kept free from scratches, grease or other dirt.

PART NAME: SATELLITE RADIO KIT PART NUMBER: KF69 V6 029 (Harness Kit P) VEHICLE: MAZDA CX-5

1ED6P11A24100

To the dealer • Please turn over these instructions to the customer after installation. To the customer • Keep these instructions after installation. The instructions may be necessary for

installing other optional parts or removal of this accessory. • Should the vehicle or this accessory be resold, always leave these instructions

with it for the next owner.

Note

WARNING

00

00 GB

00

00 F

Page 2: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-2

INSTALLATION VIEW

1

Antenna cable

AntennaANTENNA CABLE

HARNESS (P)

DLP unit

Antenna cable

Electro tap 【CAN (+) and CAN (-)】

To AUX or Bluetooth H/F

GND

Harness (P)

To Audio unit

Electro tap 【+B and ACC】

Tie redundant part (Antenna cable)

Page 3: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-3

CONNECTION DIAGRAM

2

• When connecting a connector, be sure to insert it straight along the guide. The connector terminal may be bent if inserted at an angle.

CAUTION

Antenna cable

To AUX or Bluetooth H/F

Audio visual center

To dashboard member

CAN (+)

CAN (-)

Harness (P)

CAN (-)

CAN (+)

+B

ACC

Audio 24-pin connector

ACC

GND

+B

NOCONNECT

DLP unit (SIRIUS)

24 pin connector (white)

16 pin connector(Gray) 24 pin connector

Page 4: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-4

PARTS Harness Kit P (KF69 V6 029)

Part Part name Qty. Part Part name Qty. Part Part name Qty.

Harness (P) 1

Pad protector 3

Urethane 2

Tie wrap (Small) 21

Tie wrap (Large) 5

Clip 11

Antenna 1 Alcohol wipe 2

Nut 2

Installation instructions 1

Clear tape 1

Waterproof

seal 1

DLP unit (KF69 66 DRX)

BEFORE INSTALLATION

Rating Label Removal 1. Tear off lower part of the rating label on the bottom of DLP

unit. 2. If there is nothing written in the Sirius ID (ESN) space of

the rating label, write down the 12-digit number printed in the location shown in the figure.

3. Affix one rating label in the last page of the Owner’s Manual.

3 • Verify that the kit includes all the following parts and that they are free of dirt, scratches or damage.• All hardware required to install is contained in the two Satellite Radio Kits below.

Note

4

• The other rating label is for the dealer (port) records.• Do not fail to submit the record.

Note

DLP unit

Rating label Sirius ID (ESN)

Rating label

Tear off

① Affix to the back of the Owner’s Manual. ② Submit to the manager of installation department.

② ①

gthacker
Text Box
0000-81-L17
Page 5: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-5

REQUIRED TOOLS Prepare the following tools or items before installation. ●Electrical vinyl tape ●Mat ●Scissors ●Scale ●Touch-up paint or Zinc primer ●Phillips screwdriver ●Socket driver (8 mm, 10 mm, 14 mm) ●Torx wrench ●Wrench ●File ●ISP alcohol ●Flathead screwdriver

WARNING When the negative battery cable is connected during operation, it may cause electric shock or other personal injuries. Disconnect the negative battery cable before removal/installation.

When connecting/disconnecting connectors, grasp the connectors, not the wires. Otherwise a short, an accident from poor contact or fire may occur.

Do not pull the harness with excessive force. Doing so can cause a breakage or a short-related accident, as well as an electrical short or fire.

Secure the harness with the band (part included) so it doesn’t dangle. If not, it may cause a short, accident, or fire.

CAUTION

Put the removed parts and the parts in the kit on the protective sheet to prevent scratches.

Using improper tools may cause damage and or broken parts. Use the correct tool for the job.

Be sure to cover the vehicle body with protectors or mats to prevent stains, scratches and damage when removing/installing the vehicle parts.

Excessive length of tie wrap may interfere with other parts and cause damage. Cut unnecessary part up to about 5 mm {0.19 in} from the fixed point.

Take care not to trap antenna cable under attachment nuts.

• When the negative battery cable is removed, the clock, radio, trip meters and other memories will be

erased. Before performing work, record the content of the memory.

Note

• When removing/installing the parts, park the vehicle on level ground and apply the side brake securely. Be sure to turn the ignition switch off, otherwise the vehicle can move, causing personal injury or vehicle damage.

WARNING

• During the installation of the antenna cable make sure the cable is not pinched, knotted “kinked” or coiled too tightly. It is recommended that a coil of less than 20 mm {0.78 in} be avoided if possible.

• If this wiring procedure is not followed, the performance of the antenna will be affected and could result in increased audio muting.

CAUTION

20 {0.78}

mm {in}

Page 6: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-6

PART REMOVAL

Negative battery cable disconnection 1. Set the selector lever to P range. (AT vehicles only)

2. Disconnect the negative battery cable and wrap tape around it to insulate.

Front scuff plate (passenger’s side) removal 1. Take the shaded area shown in the figure, detach tab A

while pulling the front scuff plate in the direction of the arrow (1) shown in the figure, then detach the hook B, clip C, and pin D while pulling in the direction of the arrow (2).

2. Take the shaded area shown in the figure, detach tab E while pulling the front scuff plate in the direction of the arrow (3) shown in the figure, then detach the hook F, clip G while pulling in the direction of the arrow (4).

5

• When the negative battery cable is connected during operation, it may cause electric shock or other personal injuries. Disconnect the negative battery cable before removal/installation.

WARNING

• When removing/installing the parts, park the vehicle on level ground and apply the side brake securely. Be sure to turn the ignition switch off, otherwise the vehicle can move, causing personal injury or vehicle damage.

WARNING

Negative battery cable

Hook B

(1)

(2)

(3)

(4)

Hook B Tab A

Pin D Clip C

Pin H Clip G

Hook F

Tab E

Tab A Pin D

Clip C

Pin H

Clip G

Tab E

Hook F

Front scuff plate

Page 7: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-7

Front side trim (passenger’s side) removal 1. Partially peel back the seaming welt. 2. Remove the cap nut. 3. Pull the front side trim in the direction of the arrow shown

in the figure and remove it while detaching the clip. Glove compartment removal 1. Push the glove compartment in the direction of the arrow

and remove the hook A.

2. Pull the stay damper in the direction of the arrow shown in the figure and remove the hook B.

3. Pull the glove compartment in the direction of the arrow

and remove it while detaching the hook C.

Clip

Cap nut Front side trim

Hook A

Glove compartment

Hook A

• If the glove compartment is closed without being joined to the stay damper, the stay damper may be damaged. Verify that the stay damper is joined to the glove compartment before closing the glove compartment.

CAUTION

Hook B Stay damper

Glove compartment

Hook C

Glove compartment

Page 8: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-8

Decoration panel removal

1. Insert a tape-wrapped flathead screwdriver in the position

indicated by the arrow (1) in the figure and detach clip A. 2. Take the shaded area shown in the figure, and remove

the decoration panel in the direction of the arrow in the order of (2), (3), (4) while detaching the clip B, clip C.

3. Disconnect the hazard switch connector. Center panel removal 1. Take the shaded area shown in the figure, and pull the

center panel in the direction of the arrow in the order of (1), (2), (3) and remove it while detaching the clip A, pin B and hook C.

Affix protective tape to the position shown in the figure.

CAUTION

Clip A

Clip C

Tape-wrapped flathead

screwdriver

(1)

Protective tape

(2) (3) (4)

Clip C Clip C

Clip B

Clip A

Clip B

Clip C

Clip C

Center panel

Hook C

Clip A

Clip A

Pin B

(3)(4)

(2) (1)

Clip A

Pin B

Clip A

Pin B

Clip A

Clip A

Pin B

Pin B

Clip A Clip A Clip A

Pin B

Pin B

Clip A Clip A

Page 9: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-9

Audio unit removal 1. Remove the bolt and screws.

Tightening torque Bolt: 6.9-9.8 N・m {71-99 kgf・cm, 62 – 86 in・lbf }

2. Hold the audio unit at the position shown in the figure and

pull it outward to detach clips A, B, and C from the instrument panel.

3. Disconnect the connectors. 4. Remove the audio unit.

Because the audio unit may contact the climate control unit during removing, the audio unit and the climate control unit may be damaged. Place a clean cloth as shown in the figure then perform the procedure.

CAUTION

Audio unit

Clean cloth

Audio unit

Screw

Bolt

Audio unit

Clip B

Clip A

Clip D

Clip C

Clip B

Clip A

Clip D

Clip C

Page 10: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-10

Car-navigation unit removal 1. Insert your hand from beneath the lower panel and press

the car-navigation unit to create a clearance above the car-navigation unit.

2. Insert a tape-wrapped flathead screwdriver into the clearance between the lower panel and the car-navigation unit.

3. Move the tape-wrapped flathead screwdriver in the direction of the arrow shown in the figure to detach the car-navigation clips from the lower panel.

4. Pull out the car-navigation unit and disconnect the connector.

5. While pressing the clip tabs in the direction of arrow (1)

shown in the figure, press the clip in the direction of arrow (2) and detach the clip from the car-navigation unit.

6. Remove the clip. 7. Remove the car-navigation unit.

Car-navigation unit

Affix protective tape to the position shown in the figure.

Protective tape

Car-navigation unit

CAUTION

Tape-wrapped flathead screwdriver

Car-navigation unit

Connector

Clip Clip

(1)

(1)

(2)

Page 11: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-11

Switch panel removal 1. Insert your hand from the lower side of the lower panel

(without car-navigation system) or the area where the car-navigation unit was installed (with car-navigation system), press the switch panel in the direction of the arrow (1) shown in the figure and remove it while detaching hook A and B and pin C.

2. Disconnect the cluster switch connector. 3. Remove the switch panel. Upper column cover removal 1. Pull down the steering wheel. 2. Press the shaded area shown in the figure using your

thumb, and lift the upper column cover in the direction of arrow (1).

3. Pull the upper column cover in the direction of the arrow (2) and remove it while detaching the pin A, tab B and guide C.

4. Remove the hook D from the meter hood.

Upper column cover

(1) (1)

(2)

Pin A

Tab B

Guide C

Tab B

Guide D

Tab B

Pin A

Guide C

If the cover of the meter hood is deformed, it may not return to its original condition. When removing the cover of the meter hood, detach the hooks one by one from the upper column cover.

CAUTION

Hook D

Meter hood

Hook D

Hook B

Pin C

Hook A

Switch panel

Hook B Hook A

Pin C

Page 12: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-12

Meter hood removal 1. Using a phillips screwdriver, remove fastener by rotating

the center of fastener A in the direction of the arrow shown in the figure and pulling up the shaft.

2. Take the shaded area shown in the figure, and remove

the meter hood in the direction of the arrow in the order of (1), (2) while detaching the clip A, clip B.

3. Disconnect the start switch connector. 4. Remove the meter food.

Instrument cluster removal 1. Remove the screws. 2. Cover the light switch, wiper switch, and SSCM using a

clean cloth to prevent scratches.

When pulling up the shaft of fastener using a phillips screwdriver, the shaft will not be pulled up if it is rotated by pressing the driver. To pull up the shaft of fastener, use the Phillips screwdriver to lightly contact fastener.

Note

Fastener

Meter hood

Meter hood

Pin B

Clip A

Pin B

Clip A

(1) (2)

Clip A

Pin B Clip A

Pin B

When removing the instrument cluster, the instrument cluster may contact the light switch, wiper switch, or the SSCM and the instrument cluster may be scratched. When removing the instrument cluster, cover the light switch, wiper switch, and SSCM using a rag.

CAUTION

Instrument cluster Screw

Screw

Clean cloth

Page 13: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-13

3. Pull the instrument cluster outward to detach it from the instrument panel pins.

4. Rotate the instrument cluster in the direction of the arrow

shown in the figure.

5. While pressing the tabs of the wiring harness clip in the

direction of arrows (1) shown in the figure, pull the wiring harness in the direction of arrow (2) to detach the tabs from the instrument cluster.

6. Disconnect the connector. 7. Remove the instrument cluster by sliding it between the

instrument panel and the steering.

Instrument cluster

Pin

Instrument cluster

Instrument cluster

Connector Wiring harness clip

Wiring harness clip (1) (1)

(2)

Page 14: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-14

Rear scuff plate removal 1. Take the shaded area shown in the figure, detach tab A

while pulling the rear scuff plate in the direction of the arrow (1) shown in the figure, then detach the hook B, clip C, pin D while pulling in the direction of the arrow (2).

2. Take the shaded area shown in the figure, detach tab E while pulling the rear scuff plate in the direction of the arrow (3) shown in the figure, then detach the hook F while pulling in the direction of the arrow (4).

B-pillar lower trim removal 1. Partially peel back the seaming welt. 2. Take the shaded area shown in the figure, and pull the

B-pillar lower trim in the direction of the arrow in the order of (1), (2) while detaching the hook A, pin B.

3. Take the shaded area shown in the figure, and pull the B-pillar lower trim in the direction of the arrow (3) while detaching the clip C, pin D, pin F.

Pin D

Rear scuff plate

Clip C

Tab A

Hook B Hook F

Tab E

(1)

(2)

(3)

(4)

Hook B

Pin D

Clip C

Tab E

Hook F

Pin B Hook A

Hook A (1)

(1)

(2) B-pillar lower trim Pin D

Clip C Pin F

(3)

Pin D

Pin B Pin B

Hook A

Pin D

Clip C Pin F

Pin D

Clip C

Page 15: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-15

Trunk end trim removal 1. Remove the sub trunk assembly. 2. Partially peel back the seaming welt. 3. Remove the fastener. 4. Take the shaded area shown in the figure, detach tab A

while pulling the trunk end trim in the direction of the arrow (1) shown in the figure, then detach the clip B, pin C while pulling in the direction of the arrow (2).

5. Take the shaded area shown in the figure, detach tab D while pulling the trunk end trim in the direction of the arrow (3) shown in the figure, then detach the clip E, pin F while pulling in the direction of the arrow (4).

Trunk side trim removal 1. Remove the bolts A, then remove the cargo net hook. 2. Remove the bolt A and fasteners A.

Tightening torque Bolt: 0.9-1.3 N・m {9.2-13 kgf・cm, 8 – 11 in・lbf }

3. Remove the cap, then remove the screw C.

Fastener

Trunk end trim

Tab D

Trunk end trim

(1)(2)

(3)

(1)

(3)

(4)Pin F

Pin F Clip E

Clip B

Pin C

Tab A

Tab A

Clip B

Pin C

Tab B Clip E

Pin F

Pin F Tab D

Trunk side trim

Cargo net hook

Bolt A

Cap

Screw C

Cargo net hook

Bolt A

Fastener B

Screw C

Page 16: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-16

4. Hold D-pillar trim with your hands and pull the trunk side

trim in the direction of the arrow (1), (2), (3), (4) and remove clips A, hooks B and pins B.

5. Disconnect the connector. (cargo room light connector, rear accessory socket connector)

Rear combination light removal 1. Remove the service hole cover. 2. Rotate the socket in the direction of the arrow (3) shown

in the figure and remove it from the rear combination light in the direction of the arrow (4) shown in the figure.

3. Remove the nuts.

Tightening torque Nut: 4.1-6.1 N・m {42-62 kgf・cm, 37 – 53 in・lbf }

Clip A

(1)

(2)

(3)

(4)

Hook B Hook B

Clip C

Pin D

Front side trim

Clip A

Hook B

Pin D Clip A

(3) (3)

(4) (4)

Rear turn light socket

Brake/tail light socket

Nut

Although the driver’s side is shown in the figure, remove the passenger’s side rear combination light.

Note

Page 17: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-17

4. To prevent scratches or damage, affix protective tape to

the position shown in the figure. 5. Pull the rear combination light in the direction of the

arrow (5) shown in the figure and remove the rear combination light hook from the clip.

6. Pull out the rear combination light pin. 7. Remove the rear combination light.

When the rear combination light is removed from the body, perform the procedure after affixing protective tape to the body. Otherwise, the body could interfere with the rear combination light and cause scratching or damage to the body.

CAUTION

Protective tape

Rear combination light

(5)

Rear combination light

Clip

Hook

Rear combination light

Pin

Page 18: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-18

INSTALLING ANTENNA 1. Clean the adhesion area on the roof with isopropyl

alcohol (IPA). 2. Install the antenna in the position shown in the figure.

3. Clean the adhesion area where the clear tape is

affixed with isopropyl alcohol (IPA).

4. Affix a clear tape to the body panel shown in the figure.

6

• To ensure proper affixing, be sure to degrease the area where the double-sided adhesive tape is affixed.

CAUTION

Adhesion area

mm {in}

Roof antenna

100 {3.93}

100 {3.93}

Vehicle front

• The antenna cable could interfere with the liftgate resulting in the paint peeling off. After affixing clear tape, verify that the antenna cable does not interfere with the liftgate by opening/closing the liftgate.

CAUTION

approx. 250 {9.84}

Antenna

mm {in}

Roof antenna

Vehicle front

approx. 20{0.78}

approx. 300 {11.8}

Vehicle front

Clear tape

Antenna

Antenna cable

Adhesion area

Antenna

Vehicle front

Page 19: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-19

5. Clean the adhesion area where the clips attached with isopropyl alcohol (IPA).

6. Attach the clips to the vehicle in the flat areas shown in

the figure at 100mm {3.93in} intervals. 7. Install the antenna cable to the clips.

8. Clear the adhesion area where the pad protectors and

waterproof seal are affixed with isopropyl alcohol (IPA). 9. Affix the antenna cable to the body panel using pad

protectors (1/2). 10. Affix the antenna cable to the body panel using a

waterproof seal.

• To prevent water penetration, affix a waterproof seal 5 mm away from the lip.

• When installing the Rr. combination light, route the antenna cable along the edges so that the antenna cable passes through the Rr. combination light notch.

CAUTION

• Route the antenna cable along the edges so that the antenna cable and clip do not contact the stay damper and body panel projection.

• After routing the antenna cable, verify that the antenna cable does not interfere with the liftgate.

CAUTION

mm {in}

Antenna cable

Clip

Clip

Clip

Antenna cable

mm {in} Pad protectors (1/2)

5 {0.20}

Waterproof seal

Antenna cable

Projection

Antenna cable

Notch

Rr. combination light

• To ensure proper affixing, be sure to degrease the area where the pad protectors and waterproof seal are affixed.

CAUTION

• To ensure proper affixing, be sure to degrease the area where the clips are attached.

CAUTION

100 {3.93}

Page 20: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-20

11. Secure the antenna cable to the vehicle wiring harness

with tie wraps (small). 12. Secure the antenna cable to the vehicle wiring harness

with tie wraps (small).

13. Secure the antenna cable to the vehicle wiring harness

with tie wraps (small). 14. Secure the antenna cable to the vehicle wiring harness

with tie wraps (small).

Vehicle wiring harness

Tie wraps (small)

Antenna cable

Vehicle front

Rr. wheel house (RH)

Tie wraps (small) Vehicle front

Rr. seat (RH)

Tie wraps (small) Vehicle front

Antenna cable

Vehicle front

Tie wraps (small)

ⓐ Pass through band for vehicle wiring harness securement.

Page 21: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-21

15. Secure the antenna cable to the vehicle wiring harness

with tie wraps (small).

16. Bundle the redundant part of the antenna cable using a

tie wrap (small). 17. Secure the antenna cable and the redundant part to the

vehicle wiring harness using a tie wrap (small). 18. Install the DLP unit.

• Nut tightening torque: 6.9 – 9.8 N・m {71.0 – 99.0 kgf・cm, 61.0 – 86.0 in・lbf }

19. Secure the antenna cable to the vehicle wiring harness with a tie wrap (small) and a tie wrap (large)

20. Connect the antenna cable to the DLP unit.

Vehicle front Tie wraps (small)

ⓓ ⓔ

Fr. seat (RH)

Vehicle front

Tie wraps (small)

Vehicle wiring harness

Tie redundant part (Antenna cable)

DLP unit Vehicle front

Antenna cable

Tie wrap (large)

DLP unit

Vehicle front

Tie wrap (small)

Nuts

Page 22: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-22

INSTALLING THE HARNESS

Preparation for harness (P) Prepare the wiring harnesses referring to the figure below.

7

320 {12.6}

mm {in}

700 {27.6} 50 {1.97}

100 {3.93}

50 {1.97}

670 {26.4}

Pad protector

Tie wrap (small)

Tie wrap (small)

Tie wrap (small)

【+B】

【ACC】

Page 23: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-23

1. Connect the harness (P) to the DLP unit. 2. Affix a pad protector (1/2) to the dashboard member. 3. Secure the harness (P) to the dashboard member using

tie wraps (large). 4. Branch connect the +B wire to the audio 24-pin

connector (terminal B) using the electro tap. 5. Branch connect the ACC wire to the audio 24-pin

connector (terminal R) using the electro tap.

Audio 24 pin connector (Vehicle wire) Kit wire

Terminal B +B

Terminal R ACC

6. Wrap the electro taps and vehicle wiring harness

together using urethane. 7. Pass the wiring harness (P) GND and CAN (+,-) in the

direction of the instrument cluster and insert the pad protector into the gap of the audio unit on the driver’s side.

Urethane

Terminal B: +B Kit wire: +B

Terminal R: ACC Kit wire: ACC

R B

[Audio 24 pin connector ] (View from wire side of connector)

Vehicle wiring harness

Electro-taps

Harness (P) (+B, ACC wires)

Vehicle front To instrument cluster

To audio unit

Pad protector

DLP unit

Harness (P)

Vehicle front

Pad protector (1/2)

Tie wrap (large)

Page 24: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-24

8. Branch connect the CAN (+) wires to the instrument

cluster 24-pin connector (terminal C) using the electro taps.

9. Branch connect the CAN (-) wires to the instrument cluster 24-pin connector (terminal E) using the electro taps.

Instrument cluster 24- pin connector

(Vehicle wire) Kit wire

Terminal C CAN (+)

Terminal E CAN (-)

10. Wrap the electro taps and vehicle wiring harness

together using urethane. 11. Tighten the harness (P) GND using the vehicle bolt. 12. Bundle the harness (P) GND wire redundant part to the

vehicle wiring harness using a tie wrap (small). 13. Connect the harness (P) 24-pin connector to the AUX,

Bluetooth H/F connector. 14. Bundle the harness (P) redundant part, and affix the

harness (P) 24-pin connector to the vehicle wiring harness using tie wraps (large).

• Make sure the ground eyelet contacts the steel bracket.

CAUTION

Urethane

Tie wrap (small)

Terminal E: CAN (-) Kit wire: CAN (-) Terminal C: CAN (+)

Kit wire: CAN (+)

E C

[Information display 12 pin connector] (View from wire side of connector)

Vehicle wiring harness

Electro-taps

Harness (P) (CAN (+, -) wires)

Vehicle front

GND

Harness (P)

(24-pin connector) AUX, Bluetooth H/F

Tie wrap (large) Vehicle front

Back of the audio unit

Redundant part

GTHACKER
Text Box
24
gthacker
Text Box
See "GND NOTE" below.
gthacker
Text Box
See "GND NOTE" below.
gthacker
Text Box
"GND NOTE"
gthacker
Oval
gthacker
New Stamp
Page 25: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

MAZDA CX-5-25

REINSTALLATION OF VEHICLE PARTS

• Install in the reverse order of “5. Part removal”.

• Perform the Inspection indicated on the last page of these installation instructions.

8

• After installing the vehicle parts, check for dirt. Clean any dirty parts. CAUTION

【Power window auto function】 If the battery is disconnected, the automatic full open/close feature of the power window is disabled.

This feature can be recovered by the following procedure. 1. Turn the ignition switch to the ON position. 2. Hold down the power window switch until the window is fully open. 3. Pull up the power window switch to close the window and continue to pull it up for about two

seconds after it is fully closed. 4. If the feature does not function even after the ignition switch is turned off, contact an Authorized

Mazda Dealer.

【TPMS system】 If the battery is disconnected, the TPMS (Tire Pressure Monitoring System) initial setting is reset and

the system may not operate normally. This feature can be recovered by the following procedure. 1. Adjust the tire pressure (verify tire pressure using label on body side with driver’s door open). 2. Turn the ignition switch to the ON position. 3. Press the TPMS (SET) switch (long-press it until TPMS warning light in meter flashes two times

and a beep sounds one time). 4. Switch the ignition off. 5. If the TPMS warning light illuminates or flashes even though the above procedure has been

performed, contact an Authorized Mazda Dealer.

CAUTION

Page 26: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,
Page 27: GENUINE SATELLITE RADIO KIT - TradeMotion€¦ · GENUINE SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS ... • Mazda and its suppliers are not responsible for injuries, accidents,

INSPECTION

• Inspect the installed / reinstalled parts for the following items. • Inspection parts differ depending on the vehicle.

Inspection Items (○)

Inspection Parts Clearance/Fit

Scratches/ Dirt/

Harness interference

Installation/ Tightening/

Engagement

Operation check

Rear combination light (passenger’s side) ○ ○ ○ ○

Trunk side trim (passenger’s side) ○ ○ ○ Trunk end trim ○ ○ ○

B-pillar lower trim (passenger’s side) ○ ○ ○ Rear scuff plate (passenger’s side) ○ ○ ○ Instrumetn cluster ○ ○ ○ ○ Meter hood ○ ○ ○ Upper column cover ○ ○ ○ Switch panel ○ ○ ○ Car-navigation unit ○ ○ ○ ○

Audio unit ○ ○ ○ ○*1

Center panel ○ ○ ○

Decoration panel ○ ○ ○

Glove compartment ○ ○ ○

Front side trim (passenger’s side) ○ ○ ○ Front scuff plate (passenger’s side) ○ ○ ○ Battery cable ○ ○ ○

○: Applicable *1: Refer to the Owner’s Manual and the SATELLITE RADIO instruction manual, and verify that the system

operates correctly. Ex.: Turn the power ON, increase the volume, and press the SAT button. • Direct access channel 184 is a test channel provided by Sirius.

Press the SAT button on the radio, and if properly installed you will receive a signal from the Sirius broadcast. Note: Sirius broadcasts can only be received in an open area, enclosed spaces such as garages or work

buildings block the satellite reception.

The term of validity for this sheet: 3 years

Date , , Vehicle. VIN.

Approved

Checked

Person in

charge

9

To troubleshoot problems, go to the following web page and select “Troubleshooting” in the Satellite Radio section: https://portal.mazdausa.com/dealershome/service_parts/accy_website