GE Fanuc Automation

Programmable Control Products

Series 90-70Programmable Controller

Data Sheet Manual

GFK-0600F November 1999

GFL002

Warnings, Cautions, and Notesas Used in this Publication

Warning

Warning notices are used in this publication to emphasize thathazardous voltages, currents, temperatures, or other conditions thatcould cause personal injury exist in this equipment or may beassociated with its use.

In situations where inattention could cause either personal injury ordamage to equipment, a Warning notice is used.

Caution

Caution notices are used where equipment might be damaged if care isnot taken.

Note

Notes merely call attention to information that is especially significant tounderstanding and operating the equipment.

This document is based on information available at the time of its publication. Whileefforts have been made to be accurate, the information contained herein does notpurport to cover all details or variations in hardware or software, nor to provide forevery possible contingency in connection with installation, operation, or maintenance.Features may be described herein which are not present in all hardware and softwaresystems. GE Fanuc Automation assumes no obligation of notice to holders of thisdocument with respect to changes subsequently made.

GE Fanuc Automation makes no representation or warranty, expressed, implied, orstatutory with respect to, and assumes no responsibility for the accuracy, completeness,sufficiency, or usefulness of the information contained herein. No warranties ofmerchantability or fitness for purpose shall apply.

The following are trademarks of GE Fanuc Automation North America, Inc.

Alarm MasterCIMPLICITYCIMPLICITY 90-ADSCIMSTARField ControlGEnet

GeniusHelpmateLogicmasterModelmasterMotion MatePowerTRAC

ProLoopPROMACROSeries FiveSeries 90Series OneSeries Six

Series ThreeVersaMaxVersaProVuMasterWorkmaster

Copyright 1991 - 1999 GE Fanuc Automation North America, Inc.All Rights Reserved

Series 90 -70 Programmable Controller Data Sheet Manual November 1999 iiiGFK-0600F

Preface

The Series 90-70 Programmable Logic Controller and its associated modules have beentested and found to meet or exceed the requirements of FCC Rule, Part 15, Subpart J. TheFCC requires the following note to be published.

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if notinstalled in accordance with the instruction manual, may cause interference to ra-dio communications. It has been tested and found to comply with the limits of aClass A computing device pursuant to Subpart J of Part 15 of FCC Rules, whichare designed to provide reasonable protection against such interference when op-erated in a commercial environment. Operation of this equipment in a residentialarea is likely to cause interference, in which case the user at his own expense willbe required to take whatever measures may be required to correct the interference.

The Canadian Department of Communications requires the following note to be published.

NOTE

This digital apparatus does not exceed the Class A limits for radio noise emis-sions from digital apparatus set out in the radio interference regulations of theCanadian Department of Communications.

The following statements are required to appear for Class I Div 2 Hazardous Locations.

1. EQUIPMENT LABELED WITH REFERENCE TO CLASS I, GROUPS A, B, C, and D,DIV. 2 HAZARDOUS LOCATIONS IS SUITABLE FOR USE IN CLASS I, DIVISION 2,GROUPS A, B, C, D OR NON-HAZARDOUS LOCATIONS ONLY.

2. WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAYIMPAIR SUITABILITY FOR CLASS I, DIVISION 2.

3. WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENTUNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BENON-HAZARDOUS.

4. ALL UNUSED SLOTS IN ALL BASEPLATES SHOULD BE POPULATED WITH ABLANK SLOT INTERRUPT JUMPER, IC697ACC722, OR EQUIVALENT WHENTHERE ARE MODULES INSTALLED TO ITS RIGHT WHICH MAY INTERRUPTTHE CPU.

Preface

Series 90 -70 Programmable Controller Data Sheet Manual November 1999 iv GFK-0600F

How to Find a Data Sheet in This Manual

To find the location of a data sheet in this manual:

(A). If you know the product name look for it in theTable of Contents. Its page number (at bottom of page)is listed (for example, page 5-1 is the first page of theVME Integrator Rack data sheet).

(B). Use the Index to search for a data sheet by eitherproduct category and name, product catalog number(IC.........), or by data sheet number (GFK-....).

For more information on finding data sheets in thismanual, go to the next page.

Preface

Series 90 -70 Programmable Controller Data Sheet Manual November 1999 vGFK-0600F

This manual includes all currently available hardware data sheets for the Series 90-70Programmable Logic Controller (PLC) under a single GE Fanuc publication number:GFK-0600F. On a module-by-module, and a unit-by-unit basis, this manual provides acomplete hardware description of the Series 90-70 PLC product line.

How Data Sheets are Arranged in this ManualThe data sheets in this manual are arranged in categories by type. They can easily be foundby looking in the Table of Contents or the Index.

Look in the Table of ContentsYou can find a data sheet by looking in the Table of Contents under the heading (GeneralInformation, PLC CPUs, etc.) for the product type; each data sheet is then listed by productname (type of module), catalog number (IC. . .), and number (GFK) of the data sheet.Following is an example Table of Contents entry.

Product Type PLC CPUs 12-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specific Data Sheet 12 MHz, 32 Kbyte, Central Processing Unit (IC697CPU731)

data sheet GFK-0159J 12-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The page numbers for the data sheets, as listed in the Table of Contents, are sequential inthis manual and are located at the bottom of each data sheet page. Note that each datasheet is numbered according to its location in the manual. The first data sheet starts with1-1, the 12th data sheet starts with 12-1, etc.). The page numbers for individual data sheetsremain intact at the top of the data sheet (that is, 1 through 4, 1 through 8, etc.).

Look in the IndexYou can also find a particular data sheet in the index. The index lists data sheets by producttype and name, catalog number (IC697XXXYYY), data sheet number (GFK-XXXX), and thepage number in this manual. Following are example index entries for the CPU listed above

CPUs12 MHz 32 Kbyte IC697CPU731, 12-1

GFK-0159, CPU 12 MHz 32 Kbyte, 12-1IC697CPU731, CPU 12 MHz 32 Kbyte, 12-1

Content of Data Sheets

A data sheet is a user-oriented document, packaged with each Series 90-70 PLC module,which contains information specific to the module it accompanies. The format of thedata sheet is standardized and includes the following sections (if applicable):

Features

Functions

General Description

Installation

Field Wiring

Calibration and Data Format

Specifications

Ordering Information

Preface

Series 90 -70 Programmable Controller Data Sheet Manual November 1999 vi GFK-0600F

A data sheet only provides information for hardware installation of the module in the Series90-70 system. Operation and programming of the modules is discussed in other Series 90-70documents (see Related Publications). The audience for these documents is assumed toinclude electricians, technicians, engineers and those who are familiar with digital electronicsand industrial control equipment.

Revisions to This Document

This version of the Series 90-70 Data Sheet manual has been revised to include all currentversions of applicable Series 90-70 data sheets. It contains new data sheets and revisions thathave been made to data sheets that were in the previous version of this manual(GEK-0600E). A data sheet (GFK-0867) - GE Fanuc Product Agency Approvals, Standards, GeneralSpecifications, which is at the front of the manual, lists and describes the standards to whichGE Fanuc products comply.

For those installations having more stringent installation requirements where compliance tostandards or directives from the Federal Communications Commission, the CanadianDepartment of Communications, or the European Union is necessary - refer to GFK-1179,Installation Requirements for Conformance to Standards.

References have been made on applicable data sheets to state that programming and/orconfiguration can be done either by MS-DOS (Logicmaster 90-70), or Windows(Control) software products. A note has been added, where applicable, after modulespecifications regarding availability of Conformal Coat option, or Low TemperatureTesting option.

New and Revised Data Sheets

The following data sheets are new or have been revised since the previous version ofthis manual was printed.Data Sheet Catalog PageNumber Title of Data Sheet Number Number

GFT-102H ISO 9000 Registration (Quality System) All products 1-1. . . . . . . . . . . . . . . . . . .

GFK-0867F GE Fanuc Product Agency Approvals, Standards,General Specifications Products listed 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GFK-0079K Standard Racks - Front and Rear Mount IC697CHS750/790/7914-1. . . . . . . . . . .

GFK-0684G VME Integrator Racks, 17-Slot Fro