flush handle control for atlantes … flush... · 1 installation and maintenance instructions flush...
TRANSCRIPT
1
Installation and Maintenance Instructions
FLUSH HANDLE CONTROL FOR ATLANTES FREEDOM™ TOILET VORTEX-VAC™
THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND FOLLOWED DURING BOTH INSTALLATION AND OPERATION.
WARNING: Raritan Engineering Company, Inc. recommends that a qualified person or electrician install this product. Equipment damage, injury to personnel or death could result from improper installation. Raritan Engineering Company, Inc. accepts no responsibility or liability for damage to equip-ment, injury or death to personnel that may result from improper installation or operation of this product.
WARNING: HAZARD OF SHOCK OR FIRE Always use recommended fuse, circuit breaker and wire size. DO NOT install in the area requiring “Ignition protected” devices.
TIMED FLUSH
EMPTY BOWLFLUSH
FLUSH LEVER POSITIONS
FILLWATER
Pull Handle Push Handle
“02” model:The 02 model is designed to work as a momentary unit using only microswitches to activate the motors. It is also a “fail safe” mode for the toilet control in the 03 model.
“03” model:The “03” model contains a smart toilet control which provides timed operation while still having momentary functionality if toilet control is removed.Operation:Pull Handle Forward: Model 03 - Pull handle forward and release: starts a timed flush, intake pump starts followed by discharge pump. Model 02 - Pull handle forward and hold to add water. Push Handle Backward: In both models runs just the discharge pump for a “dry bowl” flush.
Description:
03 Models: Electroscan or Purasan EX, see respective manuals.02 Models or other MSD (such as Purasan, LectraSan MC,...) Call Raritan Customer Service or visit www.raritaneng.com
If vessel is equipped with a Marine Sanitation Device and you want to start the MSD from Toilet Control:
L477 1015jlc
WIR
ING
2
Table 2- Pressurized Freshwater Model
NOTES: for Wiring
Table1-Sea Water Model
1. Distances are from source to unit and back to source.2. Distance from power source to remote intake pump
MUST be included when determining total distance. Same wire size MUST be used for lower base and remote intake pump.
3. Recommended conductor wire minimum AWG (mm²) for 3% voltage drop.
4. Recommended conductor sizes are based on 105°C rated insulation. Single conductor (not bundled), refer to ABYC Standards for sizes with other insulation ratings.
5. For 120/240 VAC units, use 12VDC specifications from transformer to unit.
CONVERSIONS
Wire - AWG to mm2
Feet to Meters
Feet 10 15 20 25 30 40 50
Meter 3.1 4.6 6.1 7.6 9.2 12.2 15.2
AWG 16 14 12 10 8 6 4 2
mm2 1.5 2.5 4.0 6.0 10.0 16.0 25.0 35.0
Recommended Wire and Fuse/Circuit Breaker Sizes
Units VoltageCircuit
Breaker/fuse size (amps)
Toilet Dis-charge Amps
draw
Remote Pump Only Amp
draw
10 feet
15 feet
20 feet
30 feet
40 feet
50 feet
12 VDC 30 18 10 10 AWG 8 AWG 6 AWG 4 AWG 4 AWG 2 AWG
24VDC 20 10 5 16 AWG 14 AWG 12 AWG 12 AWG 10 AWG 8 AWG
Units Voltage Circuit Breaker/fuse size (amps) Amp draw 10 feet 15 feet 20 feet 30 feet 40 feet 50 feet
12 VDC 25 18 10 AWG 10 AWG 8 AWG 8 AWG 6 AWG 4 AWG
24 VDC 15 10 16 AWG 16 AWG 14 AWG 12 AWG 10 AWG 10 AWG
L477 1015jlc
Table 3 - Remote Intake Pump Only (Seafresh)
Units Voltage Circuit Breaker/fuse size (amps) Amp draw 10 feet 15 feet 20 feet 30 feet 40 feet 50 feet
12 VDC 15 10 14 AWG 12 AWG 10 AWG 10 AWG 8 AWG 6 AWG
24 VDC 10 5 16 AWG 16 AWG 16 AWG 16 AWG 14 AWG 12 AWG
MOUNTING CONTROL 03 MODELS Mounting control box: 1. Locate a place for control box near toilet. Do not
install box more than six feet away to avoid excessive volatage drop
2. Route wires between toilet and control, Cut all extra lengh of wires to keep voltage drop to minimum
WIRINGWARNING: Hazard of Shock and Fire• Alwaysuseproperwire,wireconnectorsandfuse/
circuitbreaker.SeeSpecificationChart.• Securewireproperly.• Donotconnectappliancestotoiletcircuit.• Makesurepowerisoffbeforeproceeding.1. Determine proper wire size by measuring distance
from: • Power Source to toilet and back to power source. • Remote pump units - also include distance from
power source for remote pump to remote pump and back. Same wire gauge must be used for both discharge and remote pump.
2. Select proper wire and fuse/circuit breaker size from Specifications on specification page.
3. Install fuse/circuit breaker in positive line at source.4. Wire using Fig. 1, 2, 3, 4, 5, or 6
Smart Toilet Control (03 Models)
WIRING FOR FLUSH HANDLE CONTROL WITH SMART TOILET CONTROL FRESH WATER 03 MODEL
WIRING FOR FLUSH HANDLE WITH SMART TOILET CONTROL WITH REMOTE PUMP 03 MODEL
WIRING FOR FLUSH HANDLE CONTROL WITH SMART TOILET CONTROL SEAFRESH 03 MODELS
WIRING FOR MOMENTARY FLUSH HANDLE CONTROL REMOTE 02 MODEL
POSITIVEBATTERY
NEGATIVEBATTERY
BATTERY
FUSE/CIRCUIT
BREAKER
SEE RECOMMENDED
WIRE SIZE
SEE RECOMMENDED
WIRE SIZE
ORANGE/RED(14AWG)BLACK
(14AWG)
POSITIVEREMOTE INTAKE
PUMP
FIG 1
See Table 1
WIRING FOR MOMENTARY FLUSH HANDLE CONTROL FRESHWATER 02 MODEL
POSITIVEBATTERY
NEGATIVEBATTERY
BATTERY
FUSE/CIRCUIT
BREAKER
SEE RECOMMENDED
WIRE SIZE
See Table 2
FIG 2 WIR
ING
FIG 5
FIG 4FIG 3
WIRING FOR MOMENTARY FLUSH TOILET CONTROL SEAFRESH 02 MODELS
FIG 6
L477 1015jlc 3
SEA
FRESH
NEGATIVE
BATTERY
SEE RECOMMENDED
WIRE SIZE.
TABLE 2 FOR
FRESHWATER MODELS
FUSE/CIRCUIT BREAKER.
See Table 3 for Remote
Intake Pump Only
BATTERY
SEE RECOMMENDED WIRE
SIZE. Table 3 for Remote Intake
Pump Only
BLACK
RED/
ORANGE
WATER
VALVE
BLUE
(16AWG)
ORANGE
(16AWG)
ORANGE
RED
INTAKE WATER
SELECTOR SWITCH
WHITE
(16AWG)
PUMP
RELAY
BLUE
BLUE
FUSE/CIRCUIT BREAKER.
TABLE 2 FOR FRESHWATER MODELS
(BACK VIEW)
L12
3
POSITIVE
BATTERY
INTAKE
PUMP
WA
LL
SW
ITC
H
PA
NE
L
BA
TT
+
BA
TT
-
WATER
VALVE
DISCHARGE
PUMP BLACK (12AWG)
WHITE
(12AWG)
BLACK (16AWG)
BLUE (16AWG)
SEE
RECOMMENDED
WIRE SIZE
See Table 2
FUSE/
CIRCUIT BREAKER See Table 2
BATTERY
SEE
RECOMMENDED
WIRE SIZE
(Table 2)
RED
(12AWG)
STCSP
INL
ET
+ B
LU
E
DIS
CH
+ R
ED
DIS
CH
- B
LA
CK
TO
MS
D
FR
OM
MS
D
INL
ET
- B
LA
CK
FL
OA
T
CO
MM
ON
SE
NS
AL
EV
EL
WH
ITE
INTAKE
PUMP
DISCHARGE
PUMP BLACK (12AWG)
WHITE
(12AWG) BLACK
RED/ORANGE
SEE
RECOMMENDED
WIRE SIZE
See Table 1
FUSE/
CIRCUIT BREAKER See Table 1
BATTERY
SEE
RECOMMENDED
WIRE SIZE
See table 1
BLUE (12AWG)
RED
(12AWG)
BLUE (12AWG)
SEE
RECOMMENDED
WIRE SIZE
See Table 1
WA
LL
SW
ITC
H
PA
NE
L
BA
TT
+
BA
TT
-
STCSP
INL
ET
+ B
LU
E
DIS
CH
+ R
ED
DIS
CH
- B
LA
CK
TO
MS
D
FR
OM
MS
D
INL
ET
- B
LA
CK
FL
OA
T
CO
MM
ON
SE
NS
AL
EV
EL
WH
ITE
WA
LL
SW
ITC
H
PA
NE
L
BA
TT
+
BA
TT
-
SEA
FRESH
DISCHARGE
PUMP
SEE RECOMMENDED
WIRE SIZE.
TABLE 2 FOR
FRESHWATER MODELSBATTERY
BLACKRED/ORANGE
WATER
VALVE
ORANGE
RED
INTAKE WATER
SELECTOR SWITCH
(14AWG)
PUMP
RELAY
BLUE
BLUE
STC
FR
OM
MS
D
TO
MS
D
INL
ET
- B
LA
CK
INL
ET
+ B
LU
E
DIS
CH
+ R
ED
DIS
CH
- B
LA
CK
WH
ITE
FL
OA
T
SE
NS
AL
EV
EL
CO
MM
ON
REV. A
(BACK VIEW)
L12
3
FUSE/CIRCUIT BREAKER.
TABLE 2 FOR FRESHWATER MODELS
FUSE/CIRCUIT BREAKER.
See Table 3 for Remote
Intake Pump Only
SEE RECOMMENDED WIRE
SIZE. Table 3 for Remote Intake
Pump Only
BLUE (16AWG)
BLACK (16AWG)
ORANGE (16AWG)
ORANGE (16AWG)
BLACK (12AWG)
RED (12AWG)
WHITE (12AWG)
INTAKE
PUMP
4L477 1015jlc Specifications Subject to Change Without Notice Printed in U.S.A.
530 Orange Street, Millville, NJ 08332 USATelephone 856-825-4900 Fax 856-825-4409
www.raritaneng.com
For limited warranty terms and conditions please refer to toilet manualSouthern Office and Plant:3101 SW Second Avenue, Ft Lauderdale, FL 33315 USATelephone 954-525-0378 Fax 954-764-4370
NOTE: Flush control is set at factory to work in most installations. Use following instructions to re-program if adjustment on water levels and timings are needed.
NOTE: Jumper setting must be changed from 1 to 2 to allow for programming. See FIG 7. After programing is completed, return jumper to “POSITION 1”. Plug Programming Panel into controls Wall Switch Panel Jack using cable provided.
Programmingtimingfor“NORMAL”flushcycle:Normal cycle has initial fill time (T1), Discharge pump time (T2), and water retention fill time (T3). All three times (T1,T2 and T3) are programmable.Factory setting:
T1= 3sec T2= 3sec T3= 2 sec
PROGRAMMING OF FLUSH CONTROL
Tochangeanyoftheabovesettings,re-programming is needed.
Programming Panel Cable
FIG 7 Jumper Setting
Step 1 – Placing the unit in program mode: Hold the WATER ONLY & EMPTY buttons down together for three seconds. The Holding Tank Full LED will give three quick flashes indicating you have entered program mode - release both buttons.SettingT1initialfilltime:After placing the unit in program mode (Step 1 above) push the “Normal Flush” button the number of times required for the Water Valve/Inlet Pump time (one push= 2 sec’s, two = 2 sec’s., three= 3 sec’s etc.) the Tank LED will flash once indicating a valid key push. Note: If the button is pushed 9 times or more it will limit at 8 secs. Once this is done, push the EMPTY button to store this value (the unit will flash three times indicating the time has been set and you have left program mode)
Setting T2 Discharge Pump Time:After placing the unit in program mode (Step 1 above) push the EMPTY button the number of times required for the Discharge Pump time (one push = 2 seconds, two= 2 secs, three =3 secs etc.) the Tank LED will flash once indicating a valid key push. Note: If the button is pushed 9 times it will limits to 8 seconds . Once this is done push the NORMAL button to store this value (the unit will flash three times indicating the time has been set and you have left program mode).SettingT3WaterretentionfillTime: After placing the unit in program mode (Step 1 above) push the WATER ONLY button the number of times required for the Water Valve/Inlet Pump time (one push = ZERO sec’s, two = 2 secs. three = 3 sec’s., etc.) the Tank LED will flash once indicating a valid limit to 8 sec.Once this is done push the “NORMAL” button to store this value (the unit will flash three times indicating the time has been set and you have left program mode). Programming the WATER ONLY Disable Features:1. Hold the WATER ONLY & EMPTY buttons down to-
gether for three seconds. The holding tank full LED will give THREE flashes indicating you have entered program mode .
2. Push the WATER SAVER button. The WATER ONLY and EMPTY buttons now can be disabled or enabled:
3. Pushing the WATER ONLY button will disable both WATER ONLY and EMPTY buttons. The holding tank full LED will give THREE flashes indicating you have left program mode.
Repeat steps 1 to 3 to re-enable these buttons.
PR
OG
RA
MM
ING