Pipe & Tank Wrap Insulation

FLEXnWRAP is the ideal solution for insulating large diameter pipes and tanks, providing both a clean professional �nish with a high level of thermal and sound insulation.

Available in both mineral �bre or glass �bre insulation which gives the customer the option of selecting the best product for the application.

Construction is from 1” to 5” (in 1/2” increments) thickness of mineral �bre or glass �bre insulation; the grain of the �bres is perpendicular to the facing and cut every three inches to facilitate wrapping.

The insulation is then hot bonded under pressure and temperature to a �exible facing of either FSK, ASJ or Glassmat.

Finished product is nominally forty eight inches wide and o�ered in standard or custom length rolls to minimize waste and for ease of installations.

A superior product is o�ered due to our automated bonding technique that ensures even adhesion, thus eliminating the drying and adhesion problems which are commonly associated with liquid adhesives used by our competitors.

Both edges are trimmed to make it easier to obtain a tighter �t on installation.

Our FSK faced mineral �bre FLEXnWRAP has a �ame spread and smoke developed index of 5 & 10 when tested to CAN - ULC - S102.

Ordering Information: Orders for standard length rolls are normally shipped from stock within 24 hrs, with custom lengths available within 48 hrs.

Since our discount schedule is based on volume, please contact us for information on prices and terms.

FLEXnWRAP

WARRANTY: Since A&C WoolTech Solutions Inc. has no control over installation or selection for any particular application, our warranty is limited to the supply of the product as speci�ed, and does not include for any other representation. Expressed or implied warranties including merchantability or suitability for any speci�c purpose. Our obligation under this warranty is limited to either the replacement of a defective product or the equivalent replacement �nancial value for period of one year from date of shipment.

Typical Characteristics for Mineral Wool are:

Tel: 905-789-9503Toll Free: 1-888-608-9503email: sales@wooltech.ca

• ASTM C 411 - Maximum service temperature - 1200ºF (consult factory for operation at temperatures over 400ºF.

• ASTM E 136 - Material behavior @ 1382ºF - Non Combustible

• UL 723/(ASTM E 84) - Surface burning characteristics - Flame Spread = 0 - Smoke Developed = 0

• Thermal conductivity - <0.25Btu/in/hr. ºF.ft|2 @ 100ºF mean.

• ASTM C 518 - R-value @ 75ºF - 4.2/inch

• ASTM C 356 - Linear shrinkage - <2% @ 1200ºF

• ASTM C 1104 - Moisture sorption - <0.01%

• ASTM C 665 - Corrosiveness to Steel - Passed

• Density - (Nominal) - 4lb./cubic ft.

NOTE: above characteristics are manufacturers published speci�cations for material testing with the �bres oriented parallel to the testing surfaces; the �bres in FLEXnWRAP are oriented vertically.

Typical Characteristics for Foil/Scrim/Kraft (FSK) are:

• UL723/(ASTM E 84) - Surface burning characteristics - Flame spread = 5 (foil side), 25 (paper side) - Smoke Developed = 0 (foil side, 10 (paper side)

• ASTM D774 - Burst Strength - 40psi

• ASTM C665 - Mold and Mildew resistance - no growth of organism

• Humidity resistance - no growth of organism

• ASTM C1136 - Tensile strength (mach. direction) - 40lb/inch

• ASTM C1136 - Tensile strength (cross. direction) - 25lb/inch

• ASTM D1790 - Temperature Resistance / -40ºF to +240ºF

• ASTM E96 (proc. A) - Permeance - 0.02 perms

• ASTM C1136 - Puncture Resistance - 25 Beach units

• ASTM E408 - Emissivity - 0.03

A full list of speci�cation for other products are available upon request.

MATERIAL SPECIFICATION

WARRANTY: Since A&C WoolTech Solutions Inc. has no control over installation or selection for any particular application, our warranty is limited to the supply of the product as speci�ed, and does not include for any other representation. Expressed or implied warranties including merchantability or suitability for any speci�c purpose. Our obligation under this warranty is limited to either the replacement of a defective product or the equivalent replacement �nancial value for period of one year from date of shipment.