fleet synthetic enclosed gear & transmission · agma lubricant number 2 ep 3 ep 4 ep 5 ep 6 ep...

ALITHICON “FLEET” SYNTHETIC

ENCLOSED GEAR AND TRANSMISSION LUBRICANTS

THE ALITHICON “FLEET” SYNTHETIC ENCLOSED GEAR AND TRANSMISSION LUBRICANTS ARE DESIGNED AND FORMULATED FOR USE IN MANUAL TRANSMISSIONS, TRANSFER CASES, DIFFERENTIALS, AND OIL-LUBRICATED WHEEL BEARINGS FOUND IN PASSENGER CARS, TRUCK DIFFERENTIALS, FARM TRACTORS, TRAILER WHEEL BEARINGS, CONSTRUCTION, AND MISCELLANEOUS OTHER INDUSTRIAL EQUIPMENT. THE ALITHICON “FLEET” SYNTHETIC LONG-LIFE LUBRICANTS ARE RECOMMENDED FOR USE IN INDUSTRIAL GEAR DRIVES ALSO. BLENDED WITH HIGH-VISCOSITY INDEX, LOW POUR POINT SYNTHETIC BASE-STOCKS, AND COMPOUNDED WITH THE EXCLUSEIVE ALITHICON LOAD-CARRYING ADDITIVE, THESE LUBRICANTS PROVIDE MAXIMUM PROTECTION TO GEARS AND BEARINGS OPERATING OVER A WIDE RANGE OF TEMPERATURES, SPEEDS, AND LOADS. THE SUPERB RESISTANCE TO OXIDATION PROVIDES THE BENEFIT OF EXTENDED DRAIN INTERVALS.

USER BENEFITS:

* STOPS SEAL LEAKAGE * WILL NOT MIX WITH WATER

* REDUCES AMPS IN INDUSTRIAL GEAR DRIVES * NON-FOAMING

* RATES AN O.K. TIMKEN LOAD OF 100 lbs, MIN. * LOW POUR POINT OF -20° F

* REDUCES AND ELIMINATES GEAR REDUCER NOISE * EXTENDED DRAIN INTERVALS

* EXTENDS GEAR AND BEARING LIFE BY UP TO 300%

THE ALITHICON “FLEET” SYNTHETIC ENCLOSED GEAR AND TRANSMISSION OILS ARE AVAILABLE IN 3 DIFFERENT S.A.E. GRADES, AS LISTED. ALITHICON 5000 “FLEET SYNTHETIC ENCLOSED GEAR LUBRICANT (S.A.E. -50) FOR MANUAL TRUCK TRANSMISSION, REQUIRING A NON-DETERGENT, NON-E.P., S.A.E.-50, GL-1 LUBRICANT. MEETS AND EXCEEDS THE FOLLOWING MANUFACTUERS’ REQUIREMENTS: EATON TRANSMISSION DIVISION PS-164, ROCKWELL INTERNATIONAL 0-80, AND THE 750,000-MILE WARRANTY COVERAGE FOR EATON AND ROCKWELL TRANSMISSIONS. FOR ADDITIONAL INFORMATION SEE REVERSE SIDE OF THIS BROCHURE

ALITHICON 7590 “FLEET” SYNTHETIC ENCLOSED GEAR AND TRANSMISSION LUBRICANT, S.A.E.-75/w90, GL-5. ALITHICON 4585 “FLEET” SYNTHETIC ENCLOSED GEAR AND TRANSMISSION LUBRICANT, S.A.E. 85/w140, GL-5. FOR MANUAL TRANSMISSIONS AND FINAL DRIVES REQUIRING A S.A.E.-75w/90 OR S.A.E. 85w/140, GL-5 LUBRICANT. MEETS AND EXCEEDS THE FOLLOWING MANUFACTUERS’ REQUIREMENTS: U.S. MILITARY SPECIFICATIONS: MIL-L-2105D & MIL-PRF-2105E, A.P.I. SERVICE CLASSIFICATION GL-5, EATON AXLE DIVISION PS-163 & PS-109, GENERAL ELECTRIV D-50E9C, HARNISHFEGER (P&H) 474, MACK GO-H/S, MACK GO-J, SPICER AXLE DIVISION, DANA CORP, ROCKWELL INTERNATIONAL O-76-B AND ROCKWELL & EATON 750,000-MILE WARRANTY COVERAGE. THE ALITHICON “FLEET” SYNTHETIC ENCLOSED GEAR LUBRICANT STOPS LEAKS IN OIL-FILLED WHEEL BEARINGS. IT ALSO STOPS 95% OF THE LEAKS FOUND IN TRUCK DIFFERENTIALS, TRAILER WHEEL BEARINGS, ROTARY MOVER GEAR BOXES, READY-MIX CONCRETE TRUCK DRUM GEAR REDUCERS, WATER WELL DRILLING TURN TABLES, AND MUD PUMPS.

ALITHICON “FLEET” SYNTHETIC ENCLOSED GEAR AND TRANSMISSION LUBRICANTS TYPICAL TEST RESULTS

TEST-TYPE ASTM CODE < - - - - - - - - - RESULTS - - - - - - - - - - - >

* * * NOTE: LISTED ARE TYPICAL TEST RESULTS. * * * ON-SITE TEST RESULTS MAY PRODUCE A LIGHT VARIANCE.

AVAILABLE PACKAGING: 45 lb. (6 GALLON) PAIL 120 lb. (16 GALLON) KEG 420 lb. (55 GALLON) DRUM 2,100 lb. (GALLON) DISPOSABLE TOTE

ALITHICON PRODUCT CODE ASTM CODE 5000 7590 4585 S.A.E. GRADE XXX 50 75/w/90 85w/140

A.P.I. CLASSIFICATION XXX GL-1 GL-5 GL-5

A.G.M.A. GRADE XXX 4 4 5/6 COLOR XXX BRONZE BRONZE BRONZE TEXTURE XXX SMOOTH/ SMOOTH/ SMOOTH/

GRAVITY, A.P.I. D-4052 23 25.2 22.3

FLASH POINT, °F D-92 461 463 487

VISCOSITY CST @ 40°C

D-445 137 18.3

129 17.4

274 31.0

VISCOSITY INDEX D-2270 162 162 162

POUR POINT, °F D-97 -21 -21 -21

CHANNEL POINT, MAX, °F XXX -61 -56 -56

COPPER STRIP CORROSION XXX PASS PASS PASS

TIMKEN O.K. LOAD, lbs, MIN D-2509 100 100 100

ALITHICON E.P. PARA/SYNTHETIC ENCLOSED GEAR LUBRICANTS

THE ALITHICON E.P. PARA/SYNTHETIC ENCLOSED GEAR LUBRICANTS OFFER A COMPLETE LINE, OR A SELECTION OF, LONG-LIFE, EXTREME-PRESSURE GEAR OILS, FORMULATED TO LUBRICATE ALL AUTOMOTIVE AND INDUSTRIAL GEAR DRIVES. BEING A BLEND OF A HIGH QUALITY HYDRO-CRACKED, AND A FULL SYNTHETIC BASE, FLUIDS, IT IS NOT NECESSARY TO ADD VISCOSITY INDEX IMPROVERS. THE ALITHICON E.P. PARA/SYNTHETIC ENCLOSED GEAR LUBRICANTS NATURALLY POSSESSES A STRONG LUBRICANT FILM, WHICH RESISTS RUPTURE, WHEN SUBJECTED TO EXTREME PRESSURES, REDUCING OPERATING TEMPERATURES, WHILE GREATLY EXTENDING GEAR AND BEARING LIFE. THE ALITHICON E.P. PARA/SYNTHETIC ENCLOSED GEAR LUBRICANTS NOT ONLY MEET, BUT EXCEED THE MILITARY SPECIFICATIONS: MIL-L-2105D AND MIL-PRF-2105E, AS WELL AS, MACK TRUCKS GO-J, EATON AXLE DIVISION PS-037, GENERAL ELECTRIC D50E9C, U.S. STEEL 224, AGMA-250.04, ROCKWELL-STANDARD 076-A AND 076-D. ALSO FOR MANUAL TRANSMISSIONS AND AXLES MANUFACTURED BY CLARK, EATON, FULLER, INTERNATIONAL HARVESTER, SPICER, AND BORG-WARNER. THEY ARE RECOMMENDED TO LUBRICATE GEAR DRIVES WHICH REQUIRE THE API SERVICE CLASSIFICATIONS GL-4 AND GL-5, AND THEY ARE FORMULATED TO BE COMPATIBLE WITH, OR FAVORABLY MIX WITH OTHER HYDROCARBON ENCLOSED GEAR OILS. THE ALITHICON E.P. PARA/SYNTHETIC ENCLOSED GEAR LUBRICANTS ARE COMPATIBLE WITH ESSENTIALLY ALL ELASTOMERS, GASKETS, SEALS, SUCH AS: NITRITE, BUNA N, VITON, TEFLON, POLYETHYLENE, FLOUROCARBON, POLYACRYLATE, EPOXY AND PVC. THEY WILL NOT DETERIORATE ACRYLIC PAINTS OR LACQUERS.

USER BENEFITS:

* REDUCES OPERATING TEMPERATURES * WILL NOT FOAM IN SERVICE * WILL NOT MIX WITH WATER * REDUCES SEAL SEEPAGE, AS MUCH AS 80% * TIMKEN O.K. LOAD RATING, 80 lbs., MIN. * EXPECT, LONGER DRAIN INTERVALS * EXTEND GEAR AND BEARING LIFE, AS MUCH AS 300%

ALITHICON LUBRICANTS CO., INC / P O BOX 5225 / ALBANY, GEORGIA 31706 PHONE: 229-883-9515 / FAX: 229-883-9516

E-MAIL: [email protected] / WEBSITE: WWW.ALITHICON.COM

ALI

THIC

ON

E.P

. PA

RA

/SY

NTH

ETIC

EN

CLO

SED

GEA

R L

UB

RIC

AN

TS

TYP

ICA

L TE

ST R

ESU

LTS

AVA

ILA

BLE

PA

CK

AG

ING

: *

45 lb

(6 G

ALL

ON

) PA

IL

* 1

20 lb

(16

GA

LLO

N) K

EG

*

420

lb (5

5 G

ALL

ON

) DR

UM

*

2,50

0 lb

(330

GA

LLO

N) D

ISP

OS

AB

LE T

OTE

*

BU

LK

A

LITH

ICO

N L

UB

RIC

AN

TS C

O.,

INC

/ P

O B

OX

5225

/ A

LBA

NY

, G

EO

RG

IA 3

1706

PH

ON

E: 2

29-8

83-9

515

/ F

AX:

229

-883

-951

6 E

-MA

IL:

ALI

THIC

ON

@A

LITH

ICO

N.C

OM

/ W

EB

SIT

E:

WW

W.A

LITH

ICO

N.C

OM

PR

OD

UC

T I.

D. C

OD

E 6

80

6

89

6

90

6

75

6

56

6

14

6

25

SAE

VISC

OSI

TY G

RAD

E 80

EP

80w

/90

EP

90 E

P 75

w/1

40 E

P 85

w/1

40 E

P 14

0 EP

25

0 EP

ISO

GRAD

E 10

0 EP

55

EP

220

EP

24 E

P 90

EP

460

EP

1000

EP

AGM

A G

RAD

E 3

EP

4 EP

5

EP

6 EP

6

EP

7 EP

8

EP

GRAV

ITY,

° A

PI

(AST

M D

-92)

28

.9

29.0

28

.2

29.9

28

.8

26.7

21

.1

FLAS

H P

OIN

T CO

C, °

F. (

° C.

) (

ASTM

D-9

2)

496

478

492

494

492

499

193

POU

R P

OIN

T, °

F. (

° C.

) (

ASTM

D-9

7)

+3

(-1

6)

+3

(-1

6)

+3

(-1

6)

+3

(-1

6)

+3

(-1

6)

+3

(-1

6)

+15

(-

9)

TIM

KEN

O.K

. LO

AD, l

bs.,

MIN

. (A

STM

D-2

509)

>

85

> 8

5 >

85

> 8

5 >

85

> 8

5 >

85

VISC

OSI

TY I

ND

EX

(AST

M D

-227

0)

122

122

122

122

122

122

122

VISC

OSI

TY

(AST

MD

-445

)

cSt

@ 4

0° C

.

cSt

@ 1

00°

C.

VISC

OSI

TY

(AST

MD

-216

1)

cS

t @

100

° F.

cSt

@ 2

10°

F.

10

0 11

47

5 62

55

7 28

6 51

22

0 18

99

6 88

24

4.6

137

43

90

10

430

59

46

0 31

22

59

178

10

00

55

4922

26

2

FOU

R-B

ALL

WEA

R, m

m @

20

kg

(AST

M 2

266)

3

1.0

31

.2

31.6

3

1.0

32

.2

32.1

32

.4

FOU

R-B

ALL

E.P.

TES

T, W

ELD

, kg

(AS

TM D

-259

6)

262

262

266

263

262

265

262

FOAM

TES

T, S

EG I

II

(AST

M D

-892

) 0

/ 0

0 /

0 0

/ 0

0 /

0 0

/ 0

0 /

0 0

/ 0

CORRO

SIO

N, 3

hrs

@ 2

12°

F.

(AST

M D

-130

) 1A

1A

1A

1A

1A

1A

1A

RU

ST T

EST

(AS

TM D

-665

A&

B)

PASS

PA

SS

PASS

PA

SS

PASS

PA

SS

PASS

DEM

ULS

IBIL

ITY

(AS

TM D

-271

1-B)

WAT

ER I

N O

IL, %

MAX

.

TOTA

L FR

EE W

ATER

, ml,

MIN

.

EMU

LSIO

N, m

l, M

AX.

.5

12

.5

.5

12

.5

.5

13

.5

.5

11

.5

.5

12

.5

.5

12

.5

.5

14

.5

POU

ND

S PE

R G

ALLO

N

7.34

7.

32

7.37

7.

23

7.33

7

.40

7.

42

COLO

R

RED

RED

RED

RED

RED

RED

RED

SGO ALITHICON SYNTHETIC

ENCLOSED GEAR LUBRICANT THE SGO ALITHICON ENCLOSED GEAR LUBRICANT IS A HEAVY-DUTY LUBRICANT, DESIGNED FOR INDUSTRIAL AND AUTOMOTIVE USE. THE SGO ALITHICON SYNTHETIC GEAR LUBRICANT IS COMPOUNDED OF A SYNTHETIC BASE MATERIAL AND THE LATEST ADDITIVE CHEMICALS WHICH ARE SPECIFICALLY BALANCED FOR USE WITH THESE SYNTHETIC BASE STOCKS. THUS, IT PERFORMS VERY EFFECTIVELY WHERE TYPICAL PETROLEUM PRODUCTS AND OTHER SYNTHETIC GEAR LUBRICANTS FAIL. THE ALITHICON EXTREME PRESSURE PROPERTIES EXCEED THOSE OF ANY OTHER PRODUCT THAT IS AVAILABLE TODAY. THE COMBINATION OF SYNTHETIC BASE MATERIALS AND EFFECTIVE COKING AND OTHER DAMAGING DEPOSITS. THE SGO ALITHICON GEAR LUBRICANT HAS EXCELLENT HIGH AND LOW TEMPERATURE PERFORMANCE AND THE USER CAN EXPECT LONGER DRAIN INTERVALS AND EXTENDED GEAR AND BEARING LIFE. USER BENEFITS: * WILL NOT FOAM IN SERVICE * WILL NOT MIX WITH WATER * REDUCES OPERATING TEMPERATURES, GEAR REDUCERS RUN COOLER WITH SGO * LONGER DRAIN INTERVALS, OF UP TO 500% GREATER THAN PETROLEUM OILS * O.K. TIMKEN LOAD OF 100 lbs., MIN., OVER DOUBLE THE WEAR PROTECTION OF MOST GEAR LUBRICANTS ON THE MARKET * EXTENDS GEAR AND BEARING LIFE OF UP TO 300%, OVER MOST GEAR LUBRICANTS ON THE MARKET TODAY APPLICATIONS: INDUSTRIAL GEAR REDUCERS, AUTOMOTIVE GEAR REDUCERS, OIL TYPE WHEEL BEARINGS, BALL MILL / BOWL MILL GEAR DRIVES, COOLING TOWER GEAR REDUCERS, STOCK PUMP BEARINGS, CONTINUANCE CASTING PLANETARY REDUCERS, BROKE PIT PULPER REDUCERS, AERATOR GEAR DRIVES, VAN DER GRAAF HEAD ROLLER DRUM MOTOR GEAR REDUCERS, CALANDER ROLL GEAR BOXES, ETC.

THE SGO ALITHICON LUBRICANTS WILL NOT CAUSE PITTING OR CORROSION TO BRASS OR BRONZE GEARING. THE SGO ALITHICON LUBRICANTS WILL MIX WITH PETROLEUM OILS, A SAFEGUARD IN CASE MISAPPLICATION OCCURS

FOR TYPICAL SPECIFICATIONS AND TEST RESULTS, SEE REVERSE SIDE



AVAILABLE GRADES: SGO 68 - (ISO 68) - 2 EP SGO 100 - (ISO 100) - 3 EP SGO 150 - (ISO 150) - 4 EP SGO 220 - (ISO 220) - 5 EP SGO 320 - (ISO 320) - 6 EP SGO 460 - (ISO 460) - 7 EP SGO 680 - (ISO 680) - 8 EP

SGO ALITHICON SYNTHETIC ENCLOSED GEAR LUBRICANT

TYPICAL SPECIFICATIONS AND TEST RESULTS

NOTE: THE ALITHICON SGO-220 SYNTHETIC ENCLOSED GEAR LUBRICANT (EP GL-5)

MEETS AND EXCEEDS THE FOLLOWING MILITARY SPECIFICATIONS: MIL-L-2105C *** MIL-L-2105D *** PRF-2105E

AVAILABLE PACKAGING:

* 6 - 7.5 lb CANS CASE * 120 lb KEG * 45 lb PAIL * 420 lb DRUMS * BULK



PRODUCT CODE SGO 68

SGO 100

SGO 150

SGO 220

SGO 320

SGO 460

SGO 680

ISO GRADE 68 100 150 220 320 460 680 SAE VISCOSITY GRADE 20 30 40 90 90 140 140 AGMA LUBRICANT NUMBER 2 EP 3 EP 4 EP 5 EP 6 EP 7 EP 8 EP FLASH POINT, ° F. 520 450 470 480 495 520 535 POUR POINT, ° F. -60 -35 -30 -23 -20 -17 -16 VISCOSITY @ 40° C., EST. 73 100 150 220 320 460 680 VISCOSITY @ 100° C., EST. 8.8 11 14.8 18.4 24.1 31 38.2 VISCOSITY INDEX, MIN. 125 125 125 1251 125 125 125 TIMKEN O.K. LOAD IN lbs., MIN. 100 100 100 100 100 100 100

4 BALL, WEAR, mm (ASTM - 226) 40 kg / 1200 RPM, 75° C., 1 HOUR 20 kg / 1800 RPM, 54° C., 1 HOUR

0.372 0.27

0.37 0.27

0.38 0.27

0.40 0.29

0.37 0.24

0.36 0.24

0.36 0.24

THERMAL OXIDATION STABILITY OXIDATION @ 95° C., 312 HOURS (ASTM - 2893) VISC. INCR. % MAX. OXIDATION @ 121° C., 312 HOURS (ASTM - D-91) VISC. INCR. % MAX.

1.15

3.28

1.15

3.27

1.1

3.18

1

3.1

.9 1

.85

2.79

.85

2.79 ISO CLEANLINESS CODE RATING (DIS 4406)

14 / 11

14 / 11

14 /

14 / 11

14 / 11

14 / 11

14 / 11

NAS 1638 CLEANLINESS CODE RATING

5

5

5

5

5

5

5

SAE - J1165 CLEANLINESS CODE RATING

ALITHICON FM FOOD MACHINERY GEAR OIL

THE ALITHICON FOOD MACHINERY GEAR OILS ARE DESIGNED SPECIFICALLY TO LUBRICATE THE GEAR REDUCERS OF FOOD PROCESSING EQUIPMENT. THESE OILS MEET AND EXCEED F.D.A. REGULATION 21 CFR 178.35701 FOR LUBRICANTS HAVING INCIDENTAL CONTACT WITH FOOD, AND HAVE ALSO BEEN APPROVED AS H-1 LUBRICANTS FOR USE IN FOOD PLANTS UNDER THE JURISDICTION OF THE U.S.D.A. THE ALITHICON FOOD MACHINERY GEAR OILS ARE A REMARKABLE VARIETY OF LUBRICANTS FORMULATED FOR APPLICATIONS WHERE SUPERIOR PERFORMANCE IS REQUIRED, BUT WHERE PURITY IS OF THE UTMOST IMPORTANCE. THE ALITHICON FOOD MACHINERY GEAR OIL WILL NOT CREATE A PROBLEM WITH PLANT OR ANIMAL LIFE BY DAMAGING THE FOOD CHAIN, WHICH IS A CONCERN WHEN USING AN ENCLOSED GEAR LUBRICANT TO LUBRICATE GEAR DRIVES FOUND IN HYDRO LOCKS AND DAMS, AND MARINE EQUIPMENT. USER BENEFITS: * WILL NOT MIX WITH WATER, MAKING IT POSSIBLE TO GREATLY EXTEND DRAIN INTERVALS, REDUCING LUBRICANT COSTS, AND REDUCING THE EXCESSIVE COSTS FOR THE DISPOSAL OF LARGE AMOUNTS OF USED OIL. * MEETS THE REQUIREMENTS OF THE USDA FOR THE CLASSIFICATION OF H-1 (LUBRICANTS HAVING INCIDENTAL CONTACT WITH FOOD). * EXHIBITS EXCELLENT LOAD CARRYING AND ANTI-WEAR CHARACTERISTICS. * NON-FOAMING IN SERVICE. * CONTAINS AN FDA / USDA APPROVED BROAD SPECTRUM BIOCIDE, ELIMINATING THE POSSIBILITY OF MAINTAINING AND TRANSFERRING BACTERIA, FUNGUS, OR OTHER MICROBIAL ORGANISMS. * PROTECTS AGAINST RUST IN ENCLOSED GEAR REDUCERS. * RATES AN O.K. TIMKEN LOAD OF 70 lbs MIN. * EXTENDS GEAR AND BEARING LIFE BY 300%. THERE IS NO NEED TO SACRIFICE THE PERFORMANCE OF YOUR FOOD-PROCESSING MACHINERY, JUST TO MEET WITH USDA/FDA REQUIREMENTS, WHEN YOU HAVE THE ALITHICON FM FOOD MACHINERY ENCLOSED GEAR LUBRICANTS.

APPLICATIONS: FOOD PROCESSING AMD PACAKAGING MACHINERY ENCLOSED GEAR DRIVES, HYDRO LOCK & AND DAM GEAR REDUCERS, POTABLE WATER PLANT GEAR DRIVES, EXPELLER GEAR DRIVES, ETC.

PLEASE SEE REVERSE SIDE FOR TECHNICAL SPECIFICATIONS



ALITHICON FM FOOD MACHINERY GEAR OIL

TYPICAL SPECIFICATIONS:


* 6 / 1 gal CASE * 45 lbs (6 gal) PAIL * 420 lbs (55 gal) DRUMS * 330 gal NON-RETURNABLE (DISPOSABLE) TOTES * BULK



PRODUCT CODE ASTM TEST

METHOD

FM-G70 FM-G90 FM-G140

SAE VISCOSITY 80 90 140

COLOR LIGHT BLUE LIGHT BLUE LIGHT BLUE

GRAVITY, ° API D-287 30.7 29.8 29.3

FLASH POINT, COC ° F D-92 422 397 331

POUR POINT, ° F D-97 8 8 6

VISCOSITY - est @ 40° C D-445 100 220 460

EMULSION CHARACTERISITICS (OIL - WATER - EMULSION) ml

D-401 0 0 0

RUST TEST D-665 PASS (NO RUST)

PASS (NO RUST)

PASS (NO RUST)

OXIDATION STABILITY, HOURS

D-943 2,500 2,843 2,997

FOUR BALL WEAK, mm SCAR → 20 kg LOAD → 40 kg LOAD

D-226

0.12 0.16

0.11 0.15

0.10 0.13

TIMKEN O.K. LOAD, lbs MIN.

D-2782 70 70 70

VISCOSITY INDEX, MIN. D-2270 110 110 110

ISO CLEANLINESS DIS-4406 10 / 8 10 / 8 10 / 8

ALITHICON 7900 PARA/SYNTHETIC POWER FLUID (ISO 32 / 46 / 68) (SAE 10 / 20)

THE ALITHICON 7900 PARA/SYNTHETIC POWER FLUID IS THE NEXT GENERATION OR, LATEST GENERATION ATF (AUTOMATIC TRANSMISSIONS FLUID) AND HYDRAULIC FLUID. IT IS RECOMMENDED TO LUBRICATE ALL COMMERCIAL ON-HIGHWAY AUTOMATIC TRANSMISSIONS AND OFF-HIGHWAY INDUSTRIES, INCLUDING AGRICULTURE, CONSTRUCTION, LOGGINGM FARMING, AND QUARRYING EQUIPMENT, REQUIRING A TYPE-A (SUFFIX A), DEXTRON AND TYPE-F FLUIDS. IT IS ALSO RECOMMENDED AS A REPLACEMENT FOR THE CATERPILLAR TO-4 (SAE 10) AND TO-4 (SAE 30) FLUIDS, AS WELL AS ALL HYDRAULIC SYSTEMS. THE USER OF THE ALITHICON 7900 PARA/SYNTHETIC FLUID CAN EXPECT THE FOLLOWING BENEFITS: * WILL NOT MIX WITH WATER * GREATLY REDUCES OPERATING TEMPERATURES * REDUCES HYDRAULIC LEAKS AND BLOWN HOSES AS MUCH AS 80% * EXTENDS TRANSMISSIONS, HYDRAULIC PUMP AND MOTOR LIFE * REDUCES FUEL CONSUMPTION WHEN USED TO LUBRICATE AUTOMATIC TRANSMISSIONS * WILL NOT FOAM IN SERVICE * EXTENDED DRAIN INTERVALS

APPLICATIONS: ALL AUTOMATIC TRANSMISSIONS, DIFFERENTIALS, FINAL DRIVES, ALL HYDRAULIC SYSTEMS, POWER STEERING SYSTEMS, WET BRAKES, PTO’S, HYDROSTATIC DRIVES AND GEAR DRIVES REQUIRING AN API GL-4 OR SAE 80w GRADE GEAR OIL.

- - - - - -

THE ALITHICON 7900 PARA/SYNTHETIC FLUID MEETS AND EXCEEDS THE FOLLOWING INDUSTRY SPECIFICATIONS:

GENERAL MOTORS DEXTRON III *** CHRYSLER MS-7176 E *** ALLISON C-4 FORD TYPE-F AND MERCON FLUIDS *** JOHN DEERE J20C *** CATERPILLAR TO-2

J.I. CASE MS 1204 / 1205 / 1206 / 1207 / 1209 *** DENISON HF-0, HF-1, HF-2 VICKERS 35VQ25 *** MASSEY FERGUSON MF 1135 & 1141

VOLVO WB-101 / BM *** KUBOTA UDT



ALITHICON 7900 PARA/SYNTHETIC POWER FLUID TYPICAL SPECIFICATIONS AND TEST RESULTS

* NOTE #1 ALITHICON, FOR USE PERFORMANCE AND BENEFITS, RECOMMENDS THE USE OF THE ALITHICON 7900 PARA/SYNTHETIC POWER FLUID, AS A REPLACEMENT OF THE CATERPILLAR TO-4 (SAE-10 AND SAE-30) FLUIDS. MANUFACTURER’S WARRANTY REQUIREMENTS MAY BE QUESTIONED, DUE TO THE VARIATION OF USED BASE FLUIDS AND CHOSEN ADDITIVE USE, OF THIS LUBRICANT, IN THESE APPLICATIONS. A DECISION TO USE THIS FLUID IN THE ABOVE-MENTIONED APPLICATIOND IS WITH THE USERS’ UNDERSTANDING. ** NOTE #2 THE ALITHICON 7900 PARA/SYNTHETIC POWER FLUID’S SOLVENCY CLEANS WEAR METALS AND DEPOSITS, WHICH CAN BECOME SOLUBLE IN THE NEW ALITHICON 7900 FLUID, CAUSING ABNORMALLY HIGH VALUES IN USED OIL ANALYSIS, UNTIL THE EQUIPMENT IS CLEAN.

AVAILABALE PACKAGING: * 6 GALLON PAILS * 55 GALLON STEEL DRUMS

* 220 GALLON DISPOSIBLE TOTES * BULK

SPECIFICATION TEST RESULTS COLOR RED ISO GRADE (FOR USE) 32 / 46 / 68 SAE GRADE (FOR USE) 10 / 20 BASE OIL VISCOSITY (ASTM D-445) Cst @ 40° C. Cst @ 100° C. Sus @ 100° F. Sus @ 210° F.

32.8 5.86 168.4 45.9

VISCOSITY INDEX (ASTM D-2270) 199 POUR POINT (ASTM D-97) - 55 FLASH POINT (ASTM D-92) @ ° C. @ ° F.

289 572

GRAVITY, A.P.I. (ASTM D-287) 31.4 WATER SEPERABILITY (ASTM D-1401) TIME TO 40/37/3 @ 82° C., MINUTES

1.6

TIMKEN O.K. LOAD: lbs., MINUMUM (ASTM D-2782) 85 RUST PROTECTION (ASTM D-665) PASS / NO RUST FOAM TEST (ASTM D-892) TENDENCY / STABILITY, ml/ml 0 / 0 TOTAL ACID NUMBER (ASTM D-664) 0.23 ISO CLEANLINESS LEVEL 14 / 13 / 11 COPPER CORROSION TEST (ASTM D-130) 3 hrs @ 210° F. 250 hrs @ 210° F.

1A 1A

DRY AIR OXIDATION LIFE TEST, 312 hrs @ 203° F. (ASTM 2893) % VISCOSITY INCREASE PRECIP. # (% SOLIDS)

0 0

ALITHICON PARA/SYNTHETIC TURBINE OILS THE ALITHICON PARA/SYNTHETIC TURBINE OILS ARE DESIGNED FOR USE IN STEAM-TURBO GENERATORS, SMALLER TURBINES, GEAR REDUCERS CALLING FOR A NON - E.P. (EXTREME PRESSURE) LUBRICANT, BEARINGS, HYDRAULIC SYSTEMS, CIRCULATING SYSTEMS, AND AIR COMPRESSORS. THE ALITHICON PARA/SYNTHETIC TURBINE OILS WILL NOT FOAM, WILL NOT MIX WITH WATER, PREVENTS CORROSION AND WEAR, AND IS EXTREMELY LONG-LASTING IN SERVICE. FORTIFIED WITH A HIGHLY EFFECTIVE ANTI-WEAR PACKAGE, THE ALITHICON PARA/SYNTHETIC TURBINE OIL PROVIDES MAXIMUM PROTECTION AND COMPATIBILITY WITH STEEL AND COPPER SURFACES. HIGH VISCOSITY INDEX BASE OILS, WITH POUR POINT DEPRESSANTS, ENSURE A BROAD TEMPERATURE RANGE PERFORMANCE. IN REFERENCE TO THE ALITHICON PARA/SYNTHETIC TURBINE OIL'S EXTREMELY LONG SERVICE LIFE, IT HAS BEEN CLASSIFIED AS "ENVIRONMENTALLY FRIENDLY". THE ALITHICON PARA/SYNTHETIC TURBINE OILS MEET THE REQUIREMENTS OF ALL MAJOR EQUIPMENT MANUFACTURERS, INCLUDING ABEX-DENISON HF-0 AND HF-2; CINCINNATI MILACRON P-68, P-69, AND P-70; SPERRY VICKERS INDUSTRIAL AND MOBIL HYDRAULIC SYSTEMS; VICKERS 35VQ25 PUMP TEST. THEY ARE ALSO RECOMMENDED FOR USE IN GEAR REDUCERS WHERE AN API GL-1 THROUGH GL-3 GEAR PROTECTION IS REQUIRED. APPLICATIONS: ROTARY VANE, SCREW, AND RECIPROCATING AIR COMPRESSORS, ENCLOSED PARALLEL SHAFT GEARS, ENCLOSED GEAR DRIVES, PLAIN AND ANTI-FRICTION BEARINGS, ELECTRIC MOTOR BEARINGS, MACHINE TOOLS, HYDRAULIC SYSTEMS, OIL MIST BEARING LUBRICATION SYSTEMS, ETC.



AVAILABLE IN THE FOLLOWING GRADES:

6510 ISO 32 SAE 10 6515 ISO 46 SAE 20 6520 ISO 68 SAE 20 6530 ISO 100 SAE 30 6540 ISO 150 SAE 40 6550 ISO 220 SAE 50 6560 ISO 320 AGMA 6

ALIT

HIC

ON

PA

RA

/SY

NTH

ETIC

TU

RB

INE

OIL

S

PA

CK

AG

ING

:

* 6

/ 1

GAL

LON

CAS

E

*

6

GAL

LON

PLA

STIC

PAI

L

* 5

5 G

ALLO

N D

RU

M

*

33

0 G

ALLO

N N

ON

-RET

URN

ABLE

TO

TES

*

BU

LK

A

LITH

ICO

N L

UB

RIC

AN

TS C

O.,

INC

/ P

O B

OX

522

5 /

ALB

AN

Y,

GE

OR

GIA

317

06

PH

ON

E:

229-

883-

9515

/ F

AX

: 22

9-88

3-95

16

E-M

AIL

: A

LITH

ICO

N@

ALI

THIC

ON

.CO

M /

WE

BS

ITE

: W

WW

.ALI

THIC

ON

.CO

M

PR

OD

UC

T C

OD

E 65

10

6515

65

20

6530

65

40

6550

65

60

SAE

GRAD

E 10

20

20

30

40

50

60

ISO

GRAD

E 32

46

68

10

0 15

0 22

0 32

0

GRAV

ITY,

° F

. A

.P.I

. 32

.0

31.0

30

.0

29.0

29

.0

28.0

27

.0

FLAS

H P

OIN

T, C

.O.C

., °

F.

420

430

440

480

490

510

515

VISC

OSI

TY, S

.U.S

. @ 2

10°

F.

44

48

55

64

78

96

119

VISC

OSI

TY, S

.U.S

. @ 1

00°

F.

160

245

370

505

790

1220

17

00

VISC

OSI

TY I

ND

EX

121

121

121

121

121

121

121

POU

R P

OIN

T, °

F. M

AX.

-60

-6

0 -5

5 -5

5 -5

0 -5

0

COLO

R

BLU

E BL

UE

BLU

E BL

UE

BLU

E BL

UE

BLU

E

OXI

DAT

ION

LIF

E (

ASTM

D-9

43)

5,00

0 5,

000

5,00

0 5,

000

5,00

0 5,

000

5,00

0

ISO

CLE

ANLI

NES

S CO

DE

RATI

NG

NA

S 1

638

CLE

AN

LIN

ES

S C

OD

E

RA

TIN

G

SA

E -

J116

5 C

LEA

NLI

NE

SS

CO

DE

R

ATI

NG

ALITHICON FM FOOD MACHINERY TURBINE OIL

THE ALITHICON FM FOOD MACHINERY TURBINE OILS ARE FOOD GRADE LUBRICANTS, DESIGNED TO LUBRICATE FOOD PROCESSING EQUIPMENT, SUBMERGED WATER WELL PUMP BEARINGS, HYDRO DAM GEAR MECHANISMS, POTABLE WATER PLANT EQUIPMENT, ETC. THESE LUBRICANTS MEET AND EXCEED THE REQUIREMENTS OF U.S. FDA REGULATION 21 CFR 178.3570 FOR LUBRICANTS HAVING INCIDENTAL CONTACT WITH FOOD, AND HAVE ALSO BEEN APPROVED AS H-1 LUBRICANTS FOR USE IN FOOD PLANTS UNDER THE JURISDICTION OF THE USDA. THE ALITHICON FM FOOD MACHINERY TURBINE OILS ARE A REMARKABLE VARIETY OF LUBRICANTS FORMULATED FOR APPLICATIONS WHERE SUPERIOR PERFORMANCE IS REQUIRED, BUT WHERE PURITY IS OF THE UTMOST IMPORTANCE. BEING TOTALLY NON-TOXIC, THEY WILL NOT CREATE PROBLEMS WITH PLANT OR ANIMAL LIFE BY DAMAGING THE FOOD CHAIN. THE ALITHICON FM FOOD MACHINERY TURBINE OILS EXHIBIT EXCELLENT ANTI-WEAR AND NON-FOAMING CHARACTERISTICS. THE ALITHICON FM LUBRICANTS ARE SUPERIOR, LONG-LIFE, AND NON-STAINING, WHICH ARE EXCELLENT FOR USE TO LUBRICATE TEXTILE MACHINERY. USER BENEFITS: * MEETS WITH THE USDA CLASSIFICATION OF H-1 (LUBRICANTS HAVING INCIDENTAL CONTACT WITH FOOD) * EXHIBITS EXCELLENT ANTI-WEAR CAPABILITIES * ELIMINATES RUST * NON-FOAMING IN SERVICE * NON-STAINING * DESIGNED FOR HYDRAULIC SYSTEMS IN FOOD-PROCESSING PLANTS * EXCELLENT FOR USE TO LUBRICATE AIR COMPRESSORS IN FOOD-PROCESSING PLANTS CHECK THE ALITHICON LUBRICANT FOR USDA APPROVAL, FOR USE IN FOOD PROCESSING PLANTS IN

THE 2002 NSF WHITE BOOK (NSF INTERNATIONAL / NON-FOOD COMPOUNDS) AT www.nsf.org/usda APPLICATIONS:

* HYDRAULIC SYSTEMS * AIR COMPRESSORS * ROLLER CHAINS * HYDRO DAM EQUIPMENT * TEXTILE MACHINERY * POTABLE WATER PLANT EQUIPMENT

* SUBMERGED WATER WELL PUMP BEARINGS AVAILABLE PACKAGING: * 24 / 1 QUART CASE * 6 GALLON PAIL



ALITHICON FM FOOD MACHINERY LUBRICANT

TYPICAL SPECIFICATIONS AND TEST RESULTS:

ALITHICON LUBRICANTS CO., INC / P O BOX 5225 / ALBANY, GEORGIA 31706

PHONE: 229-883-9515 / FAX: 229-883-9516 E-MAIL: [email protected] / WEBSITE: WWW.ALITHICON.COM

PRODUCT CODE FM-H10 FM-H22 FM-H27 FM-H30 FM-H50 SAE GRADE 10 20 20 30 40 COLOR WATER CLEAR WATER CLEAR WATER CLEAR WATER CLEAR WATER CLEAR

SPECIFIC GRAVITY 0.925 0.912 0.95 0.951 0.87 VISCOSITY: SUS @ 40° C 32 42.3 73 108 151 VISCOSITY: SUS @ 210° C 44.6 50.6 51.4 60 72 VISCOSITY INDEX 150 150 180 189 189 POUR POINT: ° F -70 -57 -60 -60 -55 FLASH POINT: ° F 460 530 520 515 515 AUTO-IGNITION: ° F 760 760 760 760 765 ACID NUMBER 0.2 0.2 0.2 0.2 0.2 ROTARY BOMB OXIDATION 300° F LIFE MINUTES (ASTM D-2272)

720 960 1235 1340 1545

CENTRALIZED OXIDATION TEST 230° F (ASTM D-943) MED. » HOURS TO INCREASE ACID # 0.2 » HOURS TO INCREASE ACID # 2.0

1360 3375

1360 3375

1360 3375

1360 3375

1360 3375

OXIDATION CORROSSION STABILITY (FTM 5308.6) 72 HOURS @ 350° F: METAL WEIGHT (mg) » Cu, Mg, Fe, Al, Ag » EVAPORATIVE LOSS, WT. % 22 HOURS @ 210° F » SLUDGE » TAN INCREASE Mg KOH / g

± .03

.02 CLEAN

1.0

± .03

.024 CLEAN

1.4

± .03

.03 CLEAN

1.0

± .03

.05 CLEAN

2.0

± .03

.55 CLEAN

2.1

RUST PREVENTION 24 HOURS: DISTILLED WATER (ASTM D-665)

NO RUST

NO RUST

NO RUST

NO RUST

NO RUST

FOAM TENDENCY (ml) @ 15 mins (ASTM D-982) » 75° F » 200º F

> 10 / 0 > 5 / 0

> 10 / 0 > 5 / 0

> 5 / 0 > 5 / 0

> 5 / 0 > 5 / 0

> 5 / 0 > 5 / 0

DEMULSIBILITY @ 130° F OIL/WATER/EMULSION, ml (ASTM D-1401)

NO RUST

NO RUST

NO RUST

NO RUST

NO RUST CONRADSON CARBON RESIDUE WT, % (ASTM D-892) PANEL COKING, mg DEPOSIT: 6 HOURS @ 600° F

9.8

9.2

9.1

6

7.3 4 BALL, SCAR DM mm, (ASTM D-189) »10 kg @ 1800 RPM & 150° F FOR 30 MIN »40 kg @ 1200 RPM & 167° F FOR 60 MIN

0.4 0.4

0.4 0.4

0.4 0.4

0.4 0.4

0.4 0.4

VICKERS PUMP TEXT @ 150° F TOTAL WEIGHT LOSS (ASTM D-2892)

25.0

18.1

10.3

10.0

9.9

ALITHICON 9700 PARA/SYNTHETIC INDUSTRIAL POWER FLUID

THE ALITHICON 9700 PARA/SYNTHETIC INDUSTRIAL POWER FLUID IS FORMULATED FROM PREMIUM-QUALITY SYNTHETIC AND PETROLEUM BASE LUBRICANT FLUIDS, RESULTING IN A SUPERIOR MULTI-VISCOSITY LUBRICANT, DESIGNED FOR USE, TO BE USED IN HYDRAULIC SYSTEMS, VARIABLE SPEED DRIVES, PIV’S, FLUID-TYPE BEARING LUBRICANT, REEVES DRIVES, GEAR REDUCERS AND ROLLER CHAINS. THE ALITHICON 9700 PARA/SYNTHETIC INDUSTRIAL POWER FLUID IS A MULTI-VISCOSITY LUBRICANT DESIGNED, TO BE USED, TO LUBRICATE EQUIPMENT REQUIRING AN ISO-32, ISO-46, AND ISO-68 LUBRICANT, ELIMINATING THE NEED TO INVENTORY THREE OILS, WHILE MAINTAINING YOUR EQUIPMENT, WHILE GREATLY EXTENDING EQUIPMENT LIFE AND INCREASING PRODUCTION. WE ALSO, RECOMMEND TO USE THE ALITHICON 9700 PARA/SYNTHETIC INDUSTRIAL POWER FLUID IN APPLICATIONS WHERE OEM REQUIREMENTS CALL FOR AND ISO-100 FLUID. THE ALITHICON 9700 PARA/SYNTHETIC INDUSTRIAL POWER FLUID GREATLY REDUCES OPERATING TEMPERATURES AND WILL EXTEND THE LIFE OF VARIABLE-SPEED DRIVES OF UP TO 500% OVER THE MORE COMMONLY USED OILS. USER BENEFITS: * WILL NOT MIX WITH WATER * WILL NOT FOAM IN SERVICE * REDUCES OPERATING TEMPERATURES * CONTROLS RUST AND CORROSION * RESISTS OXIDATION * ELIMINATES THE NEED TO INVENTORY TWO OILS * FORTIFIED WITH EXTREME PRESSURE (EP) ADDITIVES, WHICH HAS NO ADVERSE EFFECT ON ANY METALS * REDUCES 80% OF LEAKS AND BLOWN HOSES IN HYDRAULIC SYSTEMS * EXTENDED DRAIN INTERVALS, WHICH CAN CLASSIFY IT AS ENVIRONMENTALLY FRIENDLY * GREATLY EXTENDS VARIABLE SPEED AND BEARING LIFE OF UP TO 500% APPLICATIONS: HYDRAULIC SYSTEMS, OIL-LUBRICATED BEARINGS, VARIABLE SPEED DRIVES, REEVES DRIVES, ENCLOSED GEAR REDUCERS, PIV’S, ROLLER CHAINS, AND MANY MORE.

FOR TYPICAL SPECIFICATIONS AND AVAILABLE PACKAGING, SEE REVERSE SIDE



ALITHICON 9700 PARA/SYNTHETIC INDUSTRIAL POWER FLUID


AVAILABLE PACKAGING: * 6 / 1 gal CASE * 6 gal PAIL * 55 gal DRUM * 330 gal NON-RETURNABLE (DISPOSABLE) TOTE * BULK



SPECIFICATION TEST RESULTS

COLOR BLUE

ISO GRADE (FOR USE) 32 / 46 / 68 SAE GRADE (FOR USE) 10 / 20 BASE OIL VISCOSITY (ASTM D-445) Cst @ 40° C. Cst @ 100° C. Sus @ 100° F. Sus @ 210° F.

32.8 5.86

168.4 45.9

VISCOSITY INDEX (ASTM D-2270) 149 POUR POINT (ASTM D-97) - 55 FLASH POINT (ASTM D-92) @ ° C. @ ° F.

289 572

GRAVITY, A.P.I. (ASTM D-287) 31.4 WATER SEPARABILITY (ASTM D-1401) TIME TO 40/37/3 @ 82° C., MINUTES 1.6

TIMKEN O.K. LOAD: lbs., MINIMUM (ASTM D-2782) 95

RUST PROTECTION (ASTM D-665) PASS / NO RUST

FOAM TEST (ASTM D0892) TENDENCY / STABILITY, ml/ml 0 / 0 TOTAL ACID NUMBER (ASTM D-664) 0.23

ISO CLEANLINESS LEVEL 14 / 13 / 11 COPPER CORROSION TEST (ATM D-130) 3 hrs @ 210° F. 250 hrs @ 210°F.

1A 1A

DRY AIR OXIDATION LIFE TEST, 312 hrs @ 203°F. (ASTM 2893) % VISCOSITY INCREASE

0 0

ALITHICON 822 SYNTHETIC HIGH TEMPERATURE CHAIN LUBRICANT

THE ALITHICON 822 SYNTHETIC HIGH TEMPERATURE CHAIN LUBRICANT IS FORMULATED TO PROVIDE EXTRA-LONG SERVICE LIFE IN HIGH TEMPERATURE APPLICATIONS. ITS PHYSICAL CHARACTERISTICS MAKE THE ALITHCON 822 THE IDEAL FLUID TO USE TO LUBRICATE BAKERY OVEN ROLLER CHAINS, WHICH MUST OPERATE UNDER EXTREME HIGH TEMPERATURES, ABOVE THOSE AT WHICH PETROLEUM OILS WILL NOT PERFORM SATISFACTORILY (ABOVE 400° F.). THE ALITHICON 822 SYNTHETIC HIGH TEMPERATURE CHAIN LUBRICANT IS HIGHLY RESISTANT TO THERMAL CRACKING, WHICH RESULTS IN THE FORMATION OF COKE. IT IS ALSO HIGHLY RESISTANT TO OXIDATION THICKENING. THE DISTILLATION POINT OF THE ALITHICON 822 ALLOWS CHAINS TO OPERATE AT MAXIMUM PERFORMANCE, WHEN CHAINS’ ENVIRONMENTS REACH TEMPERATURES OF, AS MUCH AS 700° F. THE ALITHICON 822 SYNTHETIC HIGH TEMPERATURE CHAIN LUBRICANT IS FORMULATED FROM A TECHNICAL GRADE, SYNTHETIC WHITE OIL, WHICH MEETS WITH FDA / USDA REQUIREMENTS, FOR USE TO LUBRICATE CHAINS IN FEDERALLY INSPECTED MEAT AND POULTRY PLANTS. IT IS ALSO NON-TOXIC AND ENVIRONMENTALLY FRIENDLY. THE ALITHICON 822 SYNTHETIC HIGH TEMPERATURE CHAIN LUBRICANT IS ALSO AVAILABLE IN A NON-DRIP FORMULATION. WHEN ORDERING THE NON-DRIP 822 CHAIN LUBRICANT, ORDER ALITHICON 822-T. CHECK THE ALITHICON LUBRICANT FOR USDA APPROVAL, FOR USE IN FOOD-PROCESSING PLANTS IN THE 2002 NSF

WHITE BOOK (NSF INTERNATIONAL / NON-FOOD COMPOUNDS) AT www.nsf.org/usda USER BENEFITS: * FORMULATED TO LUBRICATE BAKERY OVEN ROLLER CHAINS WHICH OPERATE IN EXTREMELY HIGH TEMPERATURES, OF UP TO 700° F. * ELIMINATES COKING, AND A “SOOTY CARBON” BUILDUP ON OVEN CHAIN ROLLERS * LEAVES NO RESIDUE BUILDUP WHEN THE ALITHICON 822 VAPORS ARE INCINERATED THROUGH BAKERY CATALYTIC BEDS OR SFTER-BURNERS. * FORMULATED WITH A FDA/USDA H-1 APPROVED FLUID * WATERPROOF - ELIMINATES CHAIN RUSTING WHEN USED TO LUBRICATE ROLLER CHAINS IN POULTRY PLANTS * LOW VOLATILITY - REDUCED VAPORS AND SMOKE * ENVIRONMENTALLY FRIENDLY * EXTENDS ROLLER CHAIN LIFE OF UP TO 500% LONGER THAN PETROLEUM OILS, UNDER EXTREMELY HIGH TEMPERATURE CONDITIONS

FOR TECHNICAL SPECIFICATIONS, SEE REVERSE SIDE



ALITHICON 822 SYNTHETIC HIGH TEMPERATURE CHAIN LUBRICANT

PHYSICAL CHARACTERISTICS / RESULTS

** PROPERTIES ARE TYPICAL AND MAY VARY.


* 6 / 1 GALLON CASE * 6 GALLON PAILS * 55 GALLON DRUMS * BULK



PRODUCT CODE 822 822-T BASE STOCK NF / USP GRADE

WHITE MINERAL OIL NF / USP GRADE

WHITE MINERAL OIL APPEARANCE BRIGHT, CLEAR,

COLORLESS BRIGHT, CLEAR,

COLORLESS ODOR NONE NONE TASTE NONE NONE VISCOSITY CENTISTOKES @ 40° C. (ASTM-D-445) 31 37 POUR POINT, ° F (ASTM D-97) - 90 - 85 FLASH POINT, COC, ° F. (ASTM D-92) 476 470 DENSITY @ 60° F, g / ml (ASTM D-941) 0.83 0.83 AUTOIGNITION TEMPERATURE ° F (ASTM D-2155) 708 708 EVAPORATION LOSS, N² ATMOSPHERE 760 mm, 6.5 hr. @ 400° F., WEIGHT %

4

4

% EVAPORATION LOSS @ 600° F FOR 24 hrs 5 5 % RESIDUE BUILD-UP @ 1,000° F UNTIL COMPLETE VOLATILIZATION

0

0

THERMAL CONDUCTIVITY @ 300° F., BTU / hr ft² - ° F / ln

0.91

0.91

SPECIFIC HEAT, BTU / lb - ° F 200° F 300° F 400° F 500° F 600° F

0.48 0.54 0.59 0.64 0.70

0.48 0.54 0.59 0.64 0.70

COEFFICIENT THERMAL EXPANSION @ 55° F. 0.0045 0.0045 VAPOR P² @ 300° F (ASTM D-2897) 0.7 mm / hg 0.7 mm / hg VISCOSITY @ 210° F. 5.66 5.66 SURFACE TENSION, dy / cm @ 6° F. (ASTM D-1331) 30 30

ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT

THE ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT IS A FLUID LUBRICANT, DESIGNED TO SUCCESSFULLY PROVIDE PROTECTION AND REDUCE WEAR FOR CHAINS, BEARINGS, AND JOURNALS WHICH MUST OPERATE UNDER HEAVY LOADS, IN THE PRESENCE OF WATER OR STEAM AND IN EXTREMELY HIGH TEMPERATURES. THE ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT IS DESIGNED TO GREATLY REDUCE WEAR, WHILE OPERATING UNDER HEAVY LOADS WITH AN O.K. TIMKEN LOAD RATING OF120 lbs., MIN. THE ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT IS WATERPROOF AND STEAMPROOF. IT ADHERES TO DRY METAL SURFACES AND REFUSES TO RELEASE UNDER WET WORKING ENVIRONMENTS. THE ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT IS FORMULATED TO REDUCE WEAR AND PROTECT ROLLER CHAINS WHICH MUST OPERATE IN EXTREMELY HIGH TEMPERATURES. THE ALITHICON DC-1300 LUBRICANT WILL WITHSTAND OPERATING TEMPERATURES OF UP TO 1300° F. THE ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT IS DESIGNED FOR USE IN ANY CENTRALIZED LUBRICATING SYSTEM WHICH CAN DISBURSE THE SIZE OF .05 MICRONS OR LESS. THE ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT IS AVAILABLE IN THREE ISO GRADES. USER BENEFITS: * WITHSTANDS TEMPERATURES OF UP TO 1300° F. * WATERPROOF AND STEAMPROOF - RESISTS WASH-OFF * EASILY APPLIED * RATES AN O.K. TIMKEN LOAD OD 120 lbs, MIN. * GREATLY EXTENDS CHAIN, BEARING, AND JOURNAL LIFE APPLICATIONS: TENNER FRAME CHAINS, TEXTILE DRYER CHAINS, GYPSON OVEN CHAINS, PLYWOOD VENEER DRYER CHAINS, TEXTILE HOT OIL PRESS JOURNALS, ETC.




AVAILABLE GRADES: DC-1300-AAA (ISO-15) DC-1300-AA (ISO-100) 3 EP DC-1300-A (ISO-150) 4 EP DC-1300-B (ISO-220) 5 EP DC-1300-C (ISO-320) 5 EP

ALITHICON DC-1300 SYNTHETIC HIGH TEMPERATURE LUBRICANT



* 6 / 1 GALLON CASE * 6 GALLON PAIL

* 55 GALLON DRUM * BULK



PRODUCT CODE DC-1300-AAA DC-1300-AA DC-1300-A DC-1300-B DC-1300-C ISO GRADE 15 100 150 220 320 SAE VISCOSITY GRADE 2 30 40 90 90 AGMA LUBRICANT NUMBER N/A 3 EP 4 EP 5 EP 6 EP BASE FLUID FLASH POINT, ° F 520 490 490 485 505 POUR POINT, ° F. - 40 - 30 - 30 - 20 - 20 VISCOSITY @ 40° C, EST. 15 100 150 220 320 VISCOSITY @ 100° C., EST. 3.4 10.7 17.24 19.7 29.3 TIMKEN O.K. LOAD, lbs MIN. 135 120 120 120 120 4 BALL WEAR, mm. (ASTM-226) 40 kg/1200 rpm, 75° C, 1 HOUR 20 kg/1800 rpm, 54° C, 1 HOUR

0.121 0.108

0.149 0.108

0.149 0.108

0.16 0.116

0.148 0.096

700 ALITHICON SYNTHETIC HEAT TRANSFER FLUID

THE 700 ALITHICON IS A SYNTHETIC HEAT TRANSFER FLUID, WHICH IS FORMULATED TO PROVIDE EXTRA LONG SERVICE LIFE IN HIGH TEMPERATURE SYSTEMS. ITS PHYSICAL CHARACTERISTICS MAKE THE 700 ALITHICON THE IDEAL FLUID FOR USE IN HEAT TRANSFER SYSTEMS OPERATING IN TEMPERATURE RANGES ABOVE THOSE AT WHICH PETROLEUM OIL WILL NOT PERFORM SATISFACTORILY (ABOVE 400° F.). THE ALITHICON SYNTHETIC HEAT TRANSFER IS HIGHLY RESISTANT TO THERMAL CRACKING, WHICH RESULTS IN THE FORMATION OF COKE. IT IS ALSO HIGHLY RESISTANT TO OXIDATION THICKENING. THE DISTILLATION POINT OF THE 700 ALITHICON ALLOWS SYSTEM TEMPERATURES TO OPERATE AT MAXIMUM PERFORMANCE WHEN HEAT TRANSFER SYSTEMS REACH TEMPERATURES OF, AS MUCH AS, 700° F., WITH MINIMAL VAPOR PRESSURE. THE 700 ALITHICON SYNTHETIC HEAT TRANSFER FLUID IS FORMULATED FROM A TECHNICAL GRADE. SYNTHETIC WHITE OIL, WHICH MEETS FDA/USDA SPECIFICATIONS FOR USE TO LUBRICATE MACHINERY IN FEDERALLY INSPECTED MEAT AND POULTRY PLANTS. IT IS ALSO NON-TOXIC AND DUE TO A LONGER USE LIFE, BETWEEN FLUID CHANGES, IS CLASSIFIED AS, ENVIRONMENTALLY FRIENDLY. WHEN USING THE 700 ALITHICON SYNTHETIC HEAT TRANSFER FLUID, THE USER CAN EXPECT THE ELIMINATION OF “COKING” OR “SOOTY CARBON” BUILDUP WITHIN THE SYSTEM, AS I NORMALLY FOUND WHEN USING A NORMAL PETROLEUM OIL. DRAIN OR FLUID CHANGE INTERVALS CAN BE EXTENDED AS MUCH AS 600%. PERIODIC FLUID ANALYSIS IS RECOMMENDED WHEN EXTENDING DRAIN INTERVALS.

USER BENEFITS:

FORMULATED FOR USE IN APPLICATIONS WHICH OPERATE IN SYSTEMS OF UP TO 700° F.

ELIMINATES “COKING” AND “SOOTY CARBON” BUILD-UP WITHIN THE SYSTEM

FORMULATED WITH FDA/USDA APPROVED TYPE FLUID

EXCELLENT FOR USE IN FEDERALLY INSPECTED MEAT AND POULTRY PLANTS

NON-CORROSIVE

FULLY COMPATIBLE WITH COMMONLY USED SEAL MATERIALS

LOW VOLATILITY - REDUCED VAPOR PRESSURE

SUPERIOR THERMAL CONDUCTIVITY

EXTENDED CHANGE / DRAIN INTERVALS OF UP TO 600% LONGER

CLASSIFIED AS AN ENVIRONMENTALLY FRIENDLY FLUID, DUE TO EXTENDED DRAIN INTERVALS

APPLICATIONS: FLUID FOR HEAT TRANSFER SYSTEMS

FOR PACKAGING AND TECHNICAL SPECIFICATIONS, SEE REVERSE SIDE



700 ALITHICON SYNTHETIC HEAT TRANSFER FLUID TYPICAL SPECIFICATIONS AND TEST RESULTS

AVAILABLE PACKAGING: * 6 / 1 gals CASE * 6 gal PAIL * 55 gal DRUM * 330 gal DISPOSABLE TOTE TANKS * BULK



PRODUCT CODE 700

BASE FEED STOCK NF/USP GRADE WHITE MINERAL

APPEARANCE BRIGHT, CLEAR, COLORLESS

ODOR NONE

TASTE NONE

POUR POINT, ° F. (ASTM D-97) -90

FLASH POINT, COC, ° F. (ASTM D-92) 470

DENSITY @ 60° F., gr / ml (ASTM D-972) 0.83

AUTOIGNITION TEMPERATURE (ASTM -2155) 710° F

EVAPORATION LOSS, N² ATMOSPHERE 760 mm, 6.5 hrs @ 400° F, wt % (ASTM D-972)

4.0

THERMAL CONDUCTIVITY @ 300° F., BTU / hr ft² - ° F / in

.085

SPECIFIED HEAT, BTU / lb - ° F. 200° F. 300° F. 400° F. 500° F. 600° F.

.48 .54 .59 .64 .70

COEFFICIENT THERMAL EXPANSION @ 55° F. 0.0045

VAPOR P² @ 300° F (ASTM D-2897) 0.7 mm / hg

KINEMATIC VISCOSITY cst @ 40° C. (ASTM D-445) KINEMATIC VISCOSITY cst @ 100° C. (ASTM D-445) KINEMATIC VISCOSITY sus @ 100° F. (ASTM D-445) KINEMATIC VISCOSITY sus @ 210° F. (ASTM D-445)

29 4.8 149 42

VISCOSITY INDEX (ASTM D-2270) 168

SURFACE TENSION, dy / cm @ 68° F. (ASTMD-1331) 30

ALITHICON FM-H27 PARA/SYNTHETIC CRACKER LUBRICANT

THE ALITHICON FM-H27 PARA/SYNTHETIC CACKER LUBRICANT IS DESIGNED SEPCIFICALLY FOR NUT CRACKING MACHINERY, SUCH AS PECAN, WALNUT, BRAZIL NUTS, ETC., WHERE THERE IS A POSSIBILITY OF THE LUBRICANT AND EDIBLE NUT MEAT COMING IN CONTACT. THE ALITHICON FM-H27 LUBRICANT MEETS AND EXCEEDS THE REQUIREMENTS OF U.S. REGULATION 21 CFR 178.3570 FOR LUBRICANTS HAVING INCIDENTAL CONTACT WITH FOOD , AND HAVE ALSO BEEN APPROVED AS H-1, FR USE IN FOOD PLANTS UNDER THE JURISDICTION OF THE USDA. THE ALITHICON FM-H27 LUBRICANT IS FORMULATED FOR APPLICATION WHERE SUPERIOR PERFORMANCE IS REQUIRED, BUT WHERE PURITY IS OF THE UTMOST IMPORTANCE. USER BENEFITS: * MEETS WITH THE USDA CLASSIFICATION OF H-1 (LUBRICANTS HAVING INCIDENTAL CONTACT WITH FOOD) * EXHIBITS EXCELLENT ANTI-WEAR CAPABILITIES ON THE MOVING PARTS FOUND IN NUT-CRACKING MACHINERY * ELIMINATES RUST * NON-FOAMING IN SERVICE * EXTENDS MACHINERY LIFE OF UP TO 300% OVER THE MORE COMMONLY USED LUBRICANTS

PACKAGING: * 24 / 1 QUART CASE * 6 GALLON PAIL * 6 / 1 GALLON CASE * 55 GALLON DRUM

SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS



ALITHICON FM-H27 PARA/SYNTHETIC CRACKER LUBRICANT

TYPICAL SPECIFICATIONS



SAE VISCOSITY 20 HEAVY GRAVITY, ° F., API 31.2

FLASHPOINT, COC, ° F. 418 POURPOINT, ° F. 17 VISCOSITY, est @ 40° C. 68 EMULSION CHARACTERISTICS (OIL - WATER - EMULSION) ml

40 - 37 - 3 (30 MINUTES)

RUST TEST, 24 HOURS PASS - NO RUST

OXIDATION STABILITY, HOURS 2,000 FOUR BALL WEAR, mm SCAR » 20 kg LOAD » 40 kg LOAD

0.26 0.35

VICKERS PUMP WEAR TEST WEIGHT LOSS (mg)

10

ALITHICON AL-32 PARA/SYNTHETIC AIR CYLINDER LUBRICANT

THE ALITHICON AL-32 PARA/SYNTHETIC AIR CYLINDER LUBRICANT IS A SPECIAL BLEND OF PREMIUM QUALITY PETROLEUM AND SYNTHETIC FLUIDS, FORMULATED TO ENTRAP THE MOISTURE WHICH IS NORMALLY FOUND IN AIR SUPPLY LINES AND PROVIDE SUPERIOR LUBRICATION TO AIR CYLINDERS AND AIR OPERATED TOOLS. THE SLUDGE OR BUILD-UP NORMALLY FOUND IN AIR CYLINDERS AND AIR TOOLS, AFTER FAILURE, IS COMPLETELY ELIMINATED WHEN USING THE “ALITHICON AL-32”. GALLING, SCUFFING, AND EXCESSIVE WEAR ARE GREATLY REDUCED, TOO. THE USER OF THE “ALITHICON AL-32” PARA/SYNTHETIC AIR CYLINDER LUBRICANT CAN EXPECT 600% LONGER AIR CYLINDER AND AIR TOOL LIFE WHEN USED IN PLACE OF THE MORE COMMONLY USED OILS.

USER BENEFITS: * THE ELIMINATION OF SLUDGE OR BUILD-UP * EXCELLENT PROTECTION EVEN WHEN MOISTURE IS PRESENT * GREATLY REDUCES GALLING AND SCUFFING * GREATLY REDUCES AIR TOOL AND AIR CYLINDER WEAR * EXTENDS AIR TOOL AND AIR CYLINDER LIFE BY 600%

PACKAGING: * 24 / 1 QUART CASE * 6 GALLON PAIL * 6 / 1 GALLON CASE * 55 GALLON DRUM

SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS



ALITHICON “AL-32” PARA/SYNTHETIC AIR CYLINDER LUBRICANT

TYPICAL SPECIFICATIONS



ISO GRADE 32 SAE GRADE 10

VISCOSITY @ 40° C., c.S.t. 29.6 VISCOSITY @ 100° C., c.S.t. 5.2 VISCOSITY @ 100° F., c.S.t. 155.0 VISCOSITY @ 210° F., c.S.t. 44.4

VISCOSITY INDEX 125 FLASH POINT, ° F. 445 POUR POINT, ° F. -5 GRAVITY, API 33.7

SPECIFIC GRAVITY @ 60° F. 0.87 POUNDS PER GALLON 7.11 COLOR RED



ALITHICON FM-AL-26 SYNTHETIC FOOD MACHINERY AIR CYLINDER LUBRICANT

THE ALITHICON FM-AL-26 SYNTHETIC FOOD MACHINERY AIR CYLINDER LUBRICANT IS FORMULATED WITH USDA/FDA APPROVED SYNTHETIC FULIDS AND FOOD GRADE ADDITIVES, MEETING WITH USDA/FDA APPROVED SYNTHETIC FLUIDS AND FOOD GRADE ADDITIVES, MEETING REQUIREMENTS FOR THE H-1 RATING UNDER TITLE 21 CFR. 178.3570, FOR USE IN FOOD AND POULTRY PLANTS WHERE INCIDENTAL CONTACT OF THE LUBRICANT WITH THE EDIBLE PRODUCTS BEING MANUFACTURED IS POSSIBLE. THE ALITHICON FM-AL-26 SYNTHETIC FOOD MACHINERY AIR CYLINDER LUBRICANT IS ODORLESS, TASTELESS, AND COLORLESS, WATER CLEAR, YET IT WILL GREATLY EXTEND AIR TOOL LIFE, PLUS OPTIMIZE PNUEMATIC SYSTEM PERFORMANCE. BECAUSE MOISTURE IS EVER-PRESENT IN AIR LINES, DUE TO THE EXPANSION AND COOLING OF COMPRESSED AIR, THE ALITHICON FM-AL-26 SYNTHETIC FOOD MACHINERY AIR CYLINDER LUBRICANT VIRTUALLY ELIMINATES TOOL VALVE STICKING, PREVENTS LUBRICATOR CLOGGING, AND INHIBITS POWER-THIEVINGDEPOSITS BY ABSORBING SIGNIFIGANT AMOUNTS OF MOISTURE, WHICH CAUSES GUMMING. IN ADDITION, IT GREATLY EXTENDS THE LIFE OF INTERNAL PARTS BY REDUCING FRICTION AND WEAR. WHEN USING THE ALITHICON FM-AL-26, GALLING, SCUFFING, AND GUMMING IN AIR CYLINDERS IS ELIMINATED. USER BENEFITS: * EFFECTIVE AIR CYLINDER LUBRICANT MEETING USDA/FDA H-1 REQUIREMENTS * ELIMINATES AIR CYLINDER / AIR TOOL GALLING, SCUFFING, AND GUMMING * EXTENDS AIR CYLINDER / AIR TOOL LIFE AS MUCH AS 800%

PLEASE SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS



ALITHICON FM-AL-26 SYNTHETIC FOOD MACHINERY AIR CYLINDER LUBRICANT


* 24 / 1 QUART CASE

* 6 / 1 GALLON CASE

* 6 GALLON PAIL

* 55 GALLON DRUM

* BULK

TYPICAL SPECIFICATIONS TEST RESULTS

VISCOSITY, CALCULATED SUS @ 100° F. SUS @ 210° F.

96 40

VISCOSITY, ASTM D-445 Cst. @ 40° C Cst. @ 100° c

26 4.9

VISCOSITY INDEX (ASTM D-2270) 121 LOAD CARRYLING ABILITY FALEX TEST (ASTM D-2670) NON-SIEZURE LOAD, lbs.

1095 POUR POINT (ASTM D-97) ° F. ° C.

-5 -23

RUST TEST (ASTM D-665 A) PASS

ALITHICON SYNTHETIC TURBINE OIL THE ALITHICON SYNTHETIC TURBINE OIL HAS BEEN FORMULATED, AND IS DESIGNED TO LUBRICATE INDUSTRIAL MACHINERY WHERE RESISTANCE TO EXTERNAL, RADIANT HIGH TEMPERATURES, EXTENDED DRAIN INTERVALS, COMPATIBILITY TO CERTAIN MATERIALS BEING MANUFACTURED AND PROCESSED, AND CLEANLINESS ARE NECESSARY. THE ALITHICON SYNTHETIC TURBINE OIL IS FORTIFIED WITH ANTI-WEAR (AW) AND RUST AND OXIDATION (R & O) ADDITIVES, AND WILL NOT MIX WITH WATER. THE ALITHICON SYNTHETIC TURBINE OIL WILL GREATLY REDUCE LEAKS AND BLOWN HOSES IN HYDRAULIC AND CIRCULATING SYSTEMS AND WILL ALSO GREATLY EXTEND OIL PUMP AND MOTOR LIFE. THE ALITHICON SYNTHETIC TURBINE OIL HAS AN EXTREMELY LOW POUR POINT AND A HIGH VOLITIZATION TEMPERATURE. EVEN IF THE HIGH VOLATIZATION TEMPERATURE IS REACHED, DURING MACHINERY OPERATION, THERE WILL BE NO RESIDUE GENERATED INSIDE THE EQUIPMENT. USER BENEFITS: * WILL NOT MIX WITH WATER * EXTENDED DRAIN INTERVALS * REDUCES LEAKS AND BLOWN HOSES BY 80% * WILL NOT SHELLAC, VARNISH, OR LEAVE ANY RESIDUE IF SUBJECTED TO EXTREMELY HIGH TEMPERATURES * EXTENDS LUBRICANT PUMP AND MOTOR LIFE BY 500% * COMPATIBLE WITH CERTAIN MATERIALS BEING MANUFACTURED * COLORLESS APPLICATIONS: HYDRAULIC SYSTEMS, FLUID BEARING LUBRICANT, CHAINS, CENTRIFUGES, AND MANY MORE.



ALI

THIC

ON

SYN

THET

IC T

UR

BIN

E O

IL

AVA

ILA

BLE

PA

CK

AG

ING

: *

6 /

1 G

ALL

ON

CA

SE

*

6 G

ALL

ON

PA

IL

* 5

5 G

ALL

ON

DR

UM

*

330

GA

LLO

N N

ON

-RE

TUR

NA

BLE

(DIS

PO

SA

BLE

) TO

TE

* B

ULK

__

____

____

____

____

____

____

____

____

____

____

____

____

____

____

____

____

____

____

____

____

_ A

LITH

ICO

N L

UB

RIC

AN

TS C

O.,

INC

/ P

O B

OX

522

5 /

ALB

AN

Y,

GE

OR

GIA

317

06

PH

ON

E:

229-

883-

9515

/ F

AX

: 22

9-88

3-95

16

E-M

AIL

: A

LITH

ICO

N@

ALI

THIC

ON

.CO

M /

WE

BS

ITE

: W

WW

.ALI

THIC

ON

.CO

M

PR

OD

UC

T C

OD

E 66

10

6615

66

20

6630

66

40

6650

66

60

ISO

GRAD

E 32

32

68

10

0 15

0 22

0 32

0

SAE

VISC

OSI

TY G

RAD

E 10

10

20

30

40

50

60

VISC

OSI

TY I

ND

EX

(AST

M D

-227

0)

150

150

150

165

165

165

165

POU

R P

OIN

T, °

F.

(AST

M D

-97)

-9

0 -9

0 -9

0 -8

5 -8

5 -7

0 -7

0

FLAS

H P

OIN

T, °

F.

(CO

C)

(AST

M D

-92)

49

5 49

5 49

5 50

5 50

5 51

0 51

5

AUTO

IGN

ITIO

N T

EMPE

RAT

URE

, ° F

. (A

STM

D-2

155)

71

0 71

0 71

0 71

5 71

5 72

2 72

2

EVAP

ORAT

ION

LO

SS, N

² AT

MO

SPH

ERE

760

mm

, 3

3 3

3 2

2 2

% R

ESID

UE

BUIL

D-U

P @

1,0

00°

F. U

NTI

L CO

MPL

ETE

0 0

0 0

0 0

0

RO

TARY

BOM

B O

XID

ATIO

N 3

00°

F.,

1235

12

35

1235

12

50

1370

13

90

1450

4-BA

LL, S

CAR D

M. (

mm

),

(AST

M D

-189

)

>>

10

kg @

1,8

00 R

.P.M

. @ 1

50°

F. F

OR 3

0 M

INU

TES

>

> 4

0 kg

@ 1

,200

R.P

.M. @

167

° F.

FO

R 6

0 M

INU

TES

1.

50

1.

50

1.55

1.

50

1.

50

1.

50

1.

50

1.

50

VICK

ERS

PUM

P TE

ST @

150

° F.

TOTA

L W

EIG

HT

LOSS

(A

STM

D-2

892)

9.

9

ISO

CLE

ANLI

NES

S CO

DE

RAT

ING

(D

IS-4

406)

10

/8

10/8

10

/8

10/8

10

/8

10/8

10

/8

COLO

R

CLEA

R/

CLEA

R/

CLEA

R/

CLEA

R/

CLEA

R/

CLEA

R/

CLEA

R/



1101 ALITHICON PARA/SYNTHETIC

STOKER TRAVELING GRATE

BEARING LUBRICANT THE 1101 ALITHICON PARA/SYNTHETIC STOKER TRAVELING GRATE BEARING LUBRICANT WAS FORMULATED AND FIRST USED IN A PAPER MILL POWER HOUSE STOKER IN 1982 WITH EXCELLENT RESULTS. THE ORIGINAL PAPER MILL USER EXPERIENCED A 300% INCREASE IN STOKER AND TRAVELING GRATE BEARINGS AND SHAFTS, OVER THE BEST LUBRICANT PREVIOUSLY USED. PLANNED STOKER REBUILD WAS EXTENDED FROM AN ANNUAL TASK TO A REBUILD EVERY 3 YEARS. USER BENEFITS:

WITHSTANDS HIGH TEMPERATURES, UP TO 500° F WILL NOT HARDEN IN SERVICE WILL NOT PLUG BEARING LUBRICANT FEED LINES EASILY DISPENSED BY HANDGUNS, AIR GUNS, OR CENTRALIZED LUBRICATING SYSTEMS TIMKEN O.K. LOAD RATING, 60 lbs, MIN. EXTENDS STOKER TRAVELING GRATE BEARINGS AND SHAFT LIFE OF UP TO 300% OVER THE MORE COMMONLY USED GREASE


PLEASE SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS

50 - 14.5 oz TUBE CASE 120 lb KEG

6 - 7.5 lbs CAN CASE 420 lb DRUM

45 lb PAIL BULK



1101 ALITHICON PARA/SYNTHETIC STOKER TRAVELING GRATE BEARING LUBRICANT

BASE OIL INFORMATION

1101 & 1102 LUBRICANT COMPATIBILITY

VISCOSITY, SUS @ 100° F 1225

VISCOSITY, SUS @ 210° F 75

VISCOSITY INDEX 110

BASE OIL PARTICLE COUNT RATINGS ISO CLEANLINESS CODE RATING (DIS 4406) NAS 1638 CLEANLINESS CODE RATING SAE - J1165 CLEANLINESS CODE RATING

16 / 13

7 4

COMPATIBLE INCOMPATIBLE BORDERLINE

CALCIUM 12-HYDROXY BARIUM COMPLEX CALCIUM SULFONATE COMPLEX

LITHIUM COMPLEX CALCIUM STEARATE

SILICA CALCIUM COMPLEX

ALUMINUM COMPLEX BENTONE / CLAY

LITHIUM STEARATE

LITHIUM 12-HYDROXY

POLYUREA

SODIUM

TYPICAL SPECIFICATIONS TEST RESULTS

NLGI GRADE 1

WORKED PENETRATION (ASTM D-217) 315

PROLONGED WORKED PENETRATION (ASTM D-217), % CHANGE 0.78

DROPPING POINT, MIN. (ASTM D-566), ° F 500

TIMKEN O.K. LOAD, lbs MIN. (ASTM - 2782) 60

ACID RESISTANCE EXCELLENT

ROLL STABILITY (ASTM D-1831), % CHANGE 0.6

LEAKAGE TENDENCIES, % MAX. (ASTM D-1264) 0.3

WATER WASHOUT, % MAX. (ASTM - 1264) 30° C (100° F) 79° C (175° F)

0 0

OXIDATION STABILITY, MAX. (ASTM D-942), PRESSURE DROP @ 100 HRS., KPS (PSI)

2

FOUR BALL METHOD, MAX. LOAD WHICH WELDING OCCURS, kg (lbs) (ASTM D-2598)

2.64

WEAR PREVENTATIVE CHARACTERISTICS (ASTM D-2266) MAX. SCAR DIAMETER 40 kg LOAD, 1200 RPM

3 mm

DENSITY, lbs PER GALLON 7.7

COPPER STRIP CORROSION (ASTM D-130) 1A (PASS)

2212 ALITHICON BEARING LUBRICANT

A TRULY VERSATILE, LONG-LASTING, GENERAL PURPOSE BEARING LUBRICANT, THIS PRODUCT IS FORMULATED FOR USE TO LUBRICATE BOTH FRICTION AND ANTI-FRICTION BEARINGS FOUND ON CONSTRUCTION, FARM, TRUCKING, GENERAL INDUSTRIAL BEARING MACHINERY. THE 2212 ALITHICON BEARING LUBRICANT RESISTS WATER WASH-OUT, GREATLY REDUCES LUBRICANT CONSUMPTION (AS MUCH AS 70%), WITHSTANDS TEMPERATURES OF UP TO 560° F, AND RATES AN O.K. TIMKEN LOAD OF 85 lbs, MIN. SINCE THE 2212 ALITHICON LUBRICANT REDUCES GREASE CONSUMPTION AS MUCH AS 70%, USERS FIND THAT LESS MONEY WAS SPENT PER ANNUM THAN WHEN USING THE CHEAPER GREASES THEY NORMALLY USED. THEY ALSO STATED THAT IT EXTENDED THEIR BEARING LIFE 300%, TOO. 2212 C/B (NLGI-2) IS RECOMMENDED FOR USE TO LUBRICATE ANTI-FRICTION BEARINGS WHICH OF UP TO 3,000 R.P.M.'S, MAXIMUM. 2212 C/A (NLGI-2) IS RECOMMENDED FOR USE TO LUBRICATE ANTI-FRICTION BEARINGS WHICH OPERATE ABOVE 3,000 R.P.M.'S. MEETS AND EXCEEDS MILITARY SPECIFICATIONS OF: MIL-G-18709, MIL-G-23827-B, MIL-G-25760-A, MIL-G-21164-D, MIL-G-81322-D

** REDUCE YOUR GREASE COSTS BY 35%** GUARANTEED

USER BENEFITS:

* WILL NOT MELT AND RUN FROM BEARINGS * TACKY, WILL NOT SLING FROM BEARINGS * WATER RESISTANT * FORMS ITS OWN SEAL, SEALING OUT CONTAMINATION * TIMKEN O.K. LOAD RATING OF 85 lbs, MIN. * EXTENDS BEARING LIFE OF UP TO 300%

* REDUCES GREASE CONSUMPTION AS MUCH AS 70% * CONTAINS NO SILICONES



2212 LUBRICANT COMPATIBILITY COMPATIBLE_ - - - - - - - - - - - - - INCOMPATIBLE__ - - - - - - - - - - - - ->


* 50 - 14.5 oz TUBE CASE * 120 lb KEG * 6 - 7.5 lb CANS (45 lbs) CASE * 420 lb DRUM * 45 lb PAIL * BULK SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS, TEST RESULTS, APPLICATIONS

CALCIUM STEARATE ALUMINUM COMPLEX BARIUM COMPLEX SODIUM CALCIUM HYDROXY CALCIUM COMPLEX CALCIUM SULFONATE COMPLEX LITHIUM COMPLEX

SILICA BENTONE / CLAY LITHIUM STEARATE LITHIUM 12-HYDROXY POLYUREA

2212 ALITHICON BEARING LUBRICANT CONSTRUCTION APPLICATIONS: BACKHOE AND LOADER BUCKET PINS AND BUSHINGS, UNIVERSAL JOINTS, ASPHALT PLANT INJECTION SCREW BEARINGS, ASPHALT SPREADER AUGER AND CONVEYOR BEARINGS, TRENCHER BEARINGS, CONCRETE READY MIX TRUCK DRUM ROLLER BEARINGS, ROCK QUARRY TAIL ROLLER LOAD-OUT CONVEYOR BEARINGS, ETC. FARM APPLICATIONS: TREE SHAKER BEARING LUBRICATION, TRACTOR BEARINGS PEANUT COMBINE BEARINGS, GRAIN COMBINE BEARINGS, HARROW BEARINGS, BEARING LUBRICATION FOR ALL FARM MACHINERY TRUCK APPLICATIONS: UNIVERSAL JOINTS, KING PIN AND BUSHINGS, CONCRETE READY MIX TRUCK DRUM ROLLER BEARINGS, ALL GREASE LUBRICATION FOR TRUCKS (EXCEPT AS A FIFTH WHEEL LUBRICANT; FOR THIS APPLICATION, WE RECOMMEND THE USE OF THE 9902 ALITHICON SYNTHETIC EX-TEMP LUBRICANT) GENERAL INDUSTRIAL APPLICATIONS: GENERAL PLANT PILLOW BLOCK BEARINGS, ACENTRIC BEARINGS, CONVEYOR BEARINGS, FORKLIFTS, PELLET MILL BEARINGS, EXPELLER BEARINGS, ETC. LOGGING EQUIPMENT: SKIDDER PINS & BUSHINGS, UNIVERSAL JOINTS, PIVOT PINS - FELLER BUNCHERS, BOTH SAW HEAD AND SHEAR HEAD BEARINGS - ALL GREASE / LUBE POINTS ON KNUCKLE BOOM LOADERS - LOG TRUCK CHASSIS, ETC.


PRODUCT CODE 2212 NLGI GRADE 2

WORKED PENETRATION 271 PROLONGED WORKED PENETRATIONS (ASTM D-217), % CHANGE + 0.002

DROPPING POINT, MIN. (ASTM D-566) NON-MELT RECOMMENDED OPERATING RANGE 0° F - 600° F

TIMKEN O.K. LOAD, lbs, MIN. (ASTM 2782) 85 ACID RESISTANCE EXCELLENT

ROLL STABILITY (ASTM D-1831), % CHANGE > 1.1 LEAKAGE TENDENCIES, % MAX. (ASTM D-1263) 0.3

WATER WASHOUT, % MAX. (ASTM D-12640) 39° C (100° F) 79° C (175° F)

0.7

0.85 OXIDATION STABILITY, MAX. (ASTM D-942) PRESSURE DROP @ 100 hrs, KPS (PSI)

3

FOUR BALL METHOD, MAX. LOAD WHICH WELDING 2.76 WEAR PREVENTATIVE CHARACTERISTICS (ATSM D-2666)

MAX., SCAR DIAMETER 40 kg LOAD, 1200 R.P.M.

.425 mm COLOR RED

BASE OIL: VISCOSITY SUS @ 100° F VISCOSITY CTS @ 100° C VISCOSITY SUS @ 210° F VISCOSITY CTS @ 40° C

VISCOSITY INDEX

693 15.1 77

150 110

LOW TEMP TORQUE-WHEEL BEARING, LOWEST OPERATIONAL TEMPERATURE (ASTM TEST METHOD D-

4693)

+2° F

LOW DISPENSABLE / PUMPABLE 0° F

ALITHICON 3456 SYNTHETIC FLASH-FREEZE BEARING LUBRICANT (NLGI - 2)

THE ALITHICON 3456 SYNTHETIC FLASH-FREEZE BEARING LUBRICANT IS FORMULATED AND DESIGNED TO PROLONG AND SUCESSFULLY PROTECT BEARINGS, WHICH MUST OPERATE IN EXTREMELY COLD TEMPERATURES AS LOW AS -50° F, BUT WILL ALSO PERFORM SUCESSFULLY IN TEMPERATURES AS HIGH AS +500° F. THE ALITHCON 3456 SYNTHETIC FLASH-FREEZE BEARING LUBRICANT CARRIES AN FDA / USDA RATING OF H-1, WHICH IS ACCEPTABLE FOR INCIDENTAL FOOD CONTACT. THE ALITHICON 3456 SYNTHETIC FLASH-FREEZE BEARING LUBRICANT IS VIRTUALLY WATERPROOF, RATES AN O.K. LOAD OF 70 lbs, MIN., AND IS DESIGNED TO LUBRICATE BOTH FRICTION AND ANTI-FRICTION BEARINGS. THE ALITHICON 3456 BEARING LUBRICANT IS DESIGNED TO LUBRICATE BEARINGS WITH SPEEDS OF, FROM 1 TO 7,000 R.P.M.’S. A USDA APPROVED, BROAD-SPECTRUM BIOCIDE IS FORMULATED INTO THE ALITHICON 3456 SYNTHETIC FLASH-FREEZE BEARING LUBRICANT, WHICH ELIMINATES ANY CONCERN OF PROMOTING THE GROWTH OF, OR EXTENDING THE CONTAMINATION OF THE FOOD PRODUCTS BEING MANUFACTURED OR PROCESSED. THE USDA APPROVED, BROAD-SPECTRUM BIOCIDE ELIMINATES ANY CONCERN OF TRANSFERRING, ESPECIALLY SALMONELLA IN POULTRY-PROCESSING PLANTS, UNDESIRABLE BACTERIA WHEN IT IS INTRODUCED TO THE BEARING LUBRICANT. WHEN BACTERIA IS INTRODUCED TO THE ALITHICON 3456 SYNTHETIC FLASH-FREEZE BEARING LUBRICANT, AFTER A MAXIMUM OF 30 MINUTES, THE BACTERIA IS NEUTRALIZED. IT IS NOT NECESSARY TO ACCEPT SHORT BEARING LIFE, INCREASED MAINTENANCE, AND DECREASED PRODUCTION TO COMPLY WITH THE FDA / USDA REGULATIONS WHEN THE ALITHICON 3456 SYNTHETIC FLASH-FREEZE BEARING LUBRICANT IS AVAILABLE. USER BENEFITS:

A LONG-LIFE BEARING LUBRICANT * MEETS WITH FDA / USDA H-1 REQUIREMENTS HAS A TEMPERATURE OPERATING RANGE OF FROM -50° F TO +550° F VIRTUALLY WATERPROOF * RATES AN O.K. TIMKEN LOAD OF 70 lbs, MIN. REDUCES LUBRICANT CONSUMPTION OF UP TO 300% EXTENDS BEARING LIFE OF UP TO 500%

APPLICATIONS: POULTRY, PORK, BEEF, AND VEGETABLE PROCESSING PLANTS WHICH HAVE QUICK-FREEZE DEPARTMENTS, SATILITE DISH SYSTEMS WHICH OPERATE IN EXTREMELY NORTHERN OR EXTREMELY SOUTHERN HEMISHPHERES, AND TRUCKS OR CONSTRUCTION EQUIPMENT WHICH OPERATE IN EXTREMELY COLD ENVIRONMENTS.

CHECK THIS ALITHICON LUBRICANT FOR USDA APPROVAL, FOR USE IN FOOD PROCESSING PLANTS IN THE 2002 NSF WHITE BOOK (NSF INTERNATIONAL / NON-FOOD COMPOUNDS) AT

www.nsf.org/usda



ALITHICON 3456 SYNTHETIC FLASH-FREEZE

BEARING LUBRICANT (NLGI - 2)


BASE FLUID INFORMATION 3456 LUBRICANT COMPATIBILITY


* 30 / 14.5 oz TUBE CASE * 50 / 14.5 oz TUBE CASE * 35 lb PLASTIC PAILS * 45 lb PLASTIC PAILS * 120 lb KEGS * 420 lb DRUMS * BULK



ASTM TEST RESULTS NLGI GRADE * * * * * 2 COLOR * * * * * CREAM WHITE TEXTURE * * * * * SMOOTH UN-WORKED PENETRATION D-217 280 WORKED MECHANICAL STABILITY 10,000 STROKES 100,000 STROKES

D-217 D-217

274 271

ROLL STABILITY, % CHANGE D-1831 < 1.4 DROPPING POINT, ° F D-2265 590 OIL SEPARATION D-1742 0.07

WHEEL BEARING LEAKAGE, gr D-4290 0.15 TIMKEN O.K. LOAD, lbs, MIN. D-2782 70 4 BALL E.P. TEST LOAD WEAR INDEX, kg WELD POINT, mm

D-2266

0.36 497

CORROSION RESISTANCE RUST TEST RATING SALT FOG, hrs TO FAILURE

D-1743 B-117

PASS > 450

OXIDATION RESISTANCE BEARING LIFE, hrs BOMB OXIDATION, PSI DROP AFTER 1,000 hrs

D-3527 D-942

340 4.1

WATER WASH-OUT, 79° C, % LOSS D-1264 1.2 LOW TEMP TORQUE WHEEL BEARINGS TEST @ -40° C, Nm

D-4693

1.4

DESIRABLE OPERATING TEMPERATURE RANGE -50° F TO 550° F

SPECIFICATION RESULT COMPATIBLE INCOMPATIBLE BORDERLINE

VISCOSITY @ 100° C, cst 9 BARIUM COMPLEX CALCIUM COMPLEX ALUMINUM COMPLEX

VISCOSITY @ 40° C, cst 96 CALCIUM STEARATE BENTONE / CLAY CALCIUM 12 HYDROXY VISCOSITY @ 210° C, SUS 38 LITHIUM COMPLEX POLYUREA LITHIUM STEARATE VISCOSITY @ 100° C, SUS 482 SILICA SODIUM LITHIUM-12 HYDROXY

FLASH POINT, ° F 570 CALCIUM SULFONATE COMPLEX

POUR POINT, ° F - 70

ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT (NLGI-2)

THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT IS DESIGNED TO MEET TODAY'S DEMANDING REQUIREMENTS OF THE MODERN FOOD PROCESSING EQUIPMENT, WHICH OPERATES UNDER EXTREMELY HIGH TEMPERATURES, HEAVY LOADS, HIGH SPEEDS, AND WET CONDITIONS. THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT IS FORMULATED TO PERFORM IN A SUPERIOR MANNER WITH THE FOLLOWING OUTSTANDING FEATURES: A BROAD OPERATING RANGE (-5° F TO 750° F), WATERPROOF, MECHANICALLY STABILE (RESISTANCE TO HARDENING OR SOFTENING IN SERVICE), AND RUST AND OXIDATION RESISTANCE. A USDA APPROVED, BROAD-SPECTRUM BIOCIDE IS FORMULATED INTO THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT, WHICH ELIMINATES ANY CONCERN OF PROMOTING THE GROWTH OF, OR EXTENDING THE CONTAMINATION OF THE FOOD PRODUCTS BEING MANUFACTURED OR PROCESSED. THE USDA APPROVED, BROAD-SPECTRUM BIOCIDE ELIMINATES ANY CONCERN OF TRANSFERRING, ESPECIALLY SALMONELLA IN POULTRY-PROCESSING PLANTS, UNDESIRABLE BACTERIA WHEN IT IS INTRODUCED TO THE BEARING LUBRICANT. WHEN BACTERIA IS INTRODUCED TO THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT, AFTER A MAXIMUM OF 30 MINUTES, THE BACTERIA IS NEUTRALIZED. EVEN THOUGH THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT MEETS WITH THE FDA/USDA PURITY REQUIREMENTS, WITH AN H-1 RATING FOR INCIDENTAL CONTACT WITH THE FOOD PRODUCTS BEING PROCESSED, IT IS RECOMMENDED TO BE USED AS ONE LUBRICANT, TO LUBRICATE ALL BEARINGS WHICH HAS TO BE LUBRICATED WITH AN NLGI-1 OR AN NLGI-2 GREASE, EVEN ELECTRIC MOTOR BEARINGS. THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT CONTAINS NO TEFLON OR PTFE, AND IS THE PREFERRED BEARING LUBRICANT FOR USE TO LUBRICATE BEARINGS WHICH PROCESS TOBACCO. SINCE THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT IS COMPATIBLE WITH, AND WILL MIX FAVORABLY WITH ALL OTHER GREASES, CONCERN IN MIXING GREASES, OR CHANGE OVER FLUSHING PROCEDURES, ARE NOT NECESSARY. WITH THE AVAILABILITY OF THE ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT, IT IS NOT NECESSARY TO SETTLE FOR SHORT BEARING LIFE, DECREASED PRODUCTION, AND EXCESSIVE EQUIPMENT REPAIRS, JUST TO MEET WITH THESE USDA/FDA PURITY REQUIREMENTS. ALSO AVAILABLE AS ALITHICON #4521-FM FOOD MACHINERY LUBRICANT (NLGI-1).

THE ALITHICON #4521-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT (NLGI-1) IS AN EXCELLENT CHOICE TO PUMP THROUGH CENTRALIZED LUBE SYSTEMS, WHICH ARE

DESIGNED FOR PUMPING A LIGHT-WEIGHT GREASE OR A HEAVY-WEIGHT OIL.



ALITHICON 4522-FM SYNTHETIC FOOD MACHINERY BEARING LUBRICANT (NLGI-2)

USER BENEFITS:

* TOTALLY WATERPROOF * DOES NOT CONTAIN TEFLON,PTFE, OR SILICONES. * ANTI-MICROBIAL ** ANTI-FUNGAL ** ANTI-BACTERIAL * WITHSTANDS HIGH TEMPERATURES OF UP TO 750° F * PREVENTS RUSTING IN BEARINGS * RATES AN O.K. TIMKEN LOAD OF 80 lbs., MIN. * MEETS THE FDA / USDA OF H-1 FOR PURITY * TACKY - REDUCES LUBRICANT CONSUMPTION AS MUCH AS 500% * EXTENDS BEARING LIFE AS MUCH AS 400%

APPLICATIONS: POULTRY PROCESSING MACHINERY, PICKER BEARINGS, PORK PROCESSING MACHINERY, BEEF PROCESSING MACHINERY, BAKERY MACHINERY, BOTTLING PLANT MACHINERY, FILLING MACHINES, CROWNERS, BOTTLE WASHERS, TOBACCO PROCESSING MACHINERY, ELECTRICAL POWER GENERATING TRAVELING SCREENS, DAIRY EQUIPMENT, ETC. THE ALITHICON 4521-FM AND ALITHICON 4522-FM ARE EXCELLENT CHOICES FOR LUBRICATING COUPLINGS, WHICH OPERATE FROM 1 - 5,000 R.P.M.’S.

CHECK THE ALITHICON LUBRICANT FOR USDA APPROVAL, FOR USE IN FOOD PROCESSING PLANTS IN THE 2002 NSF WHITE BOOK (NSF INTERNATIONAL / NON-FOOD COMPOUNDS) AT

www.nsf.org/usda TYPICAL SPECIFICATIONS:

AVAILABLE PACKAGING: • 30 - 14.5 oz TUBES / CASE • 120 lb KEG • 50 - 14.5 oz TUBES / CASE • 420 lb DRUM • 35 lb PAIL • BULK

ALITHICON 4522-FM LUBRICANT COMPATIBILITY COMPATIBLE

CALCIUM 12-HYDROXY BARIUM COMPLEX CALCIUM SULFONATE COMPLEX LITHIUM COMPLEX CALCIUM STEARATE LITHIUM STEARATE SILICA CALCIUM COMPLEX LITHIUM 12-HYDROXY ALUMINUM COMPLEX BENTONE / CLAY POLYUREA SODIUM



PRODUCT CODE 4521-FM 4522-FM NLGI GRADE 1 2 WORKED PENETRATION, 60 STROKES (ASTM D-217) 339 290 DROPPING POINT, MINIMUM (ASTM D-566) NONE NONE LUBRICATING OPERATING RANGE -8 TO 750° F. -5° TO 750° F. TIMKEN O.K. LOAD, lbs, MINIMUM (ASTM D-2782) 80 80 ACID RESISTANCE EXCELLENT EXCELLENT WATER WASHOUT, % MAX. 38° C. (100° F) 70° C. (175° F.)

D-1264 0.02 0.02

FOUR BALL METHOD, MAX. LOAD WHICH WELDING OCCURS D-2596 3.94 COLOR CLEAR CLEAR TEXTURE SLIGHT TACK SLIGHT TACK EVAPORATION LOSS @ 350° F, WT. % (ASTM D-2595) 0.2 0.2 USP SYNTHETIC HYDROCARBON BASE OIL VISCOSITY @ 40° C 150 150 BASE FLUID VISCOSITY INDEX 120 120

ALITHICON 9992-TL PARA/SYNTHETIC BEARING LUBRICANT

THE 9992-TL ALITHICON PARA/SYNTHETIC BEARING LUBRICANT WAS INITIALLY FORMULATED TO WITHSTAND THE HARSH, WET, AND HIGH TEMPERATURE ENVIRONMENTS COMMONLY FOUND IN THE TEXTILE INDUSTRY. AFTER THE INTRODUCTION OF THE 9992-TL ALITHICON, IT WAS TESTED AND FOUND TO BE FAR-SUPERIOR TO LUBRICANTS NORMALLY BEING USED IN THE PAPER INDUSTRY, SEWAGE TREATMENT PLANTS, AND OTHER INDUSTRIES WHERE THESE HARSH, WET ENVIRONMENTS ARE FOUND. THE ALITHICON 9992-TL ALSO THE PERFERRED LUBRICANT TO LUBRICATE BEARINGS FOUND ON SKI RESORT AND GOLF COURSE EQUIPMENT. THE ALITHICON 9992 LUBRICANT WILL NOT KILL GRASS, UNDER NORMAL USE. MEETS AND EXCEEDS MILITARY SPECIFICATIONS FOR MIL-G-18709 AND MIL-G-18709 (AMEND 3)

USER BENEFITS: * WATERPROOF * CONTAINS NO SILICONES * RESISTS DECOMPOSITION WHEN INTRODUCED TO MOST ACIDS * ACCEPTABLE OPERATING TEMPERATURE RANGE: - 40° F. TO 595° F. * RATES AN O.K. TIMKEN LOAD OF 85 lbs., MIN. * REDUCES LUBRICANT CONSUMPTION OF UP TO 300% * EXTENDS BEARING LIFE OF UP TO 500% * WILL NOT SLING FROM BEARINGS * MEETS WITH USDA REQUIREMENTS OF H-2 FOR LUBRICATING EQUIPMENT BEARINGS FOUND IN FOOD-PROCESSING PLANTS

APPLICATIONS: (TEXTILE PLANTS) WASH BOX BEARINGS, DYE VAT BEARINGS, DYE RANGE BEARINGS ( PAPER MILL) WET END BEARINGS, PUMP BEARINGS, FLOCKULATOR BEARINGS, ** SEWAGE TREATMENT PLANT BEARINGS ** BOAT TRAILER WHEEL BEARINGS, ELECTRIC MOTOR BEARINGS, ROBBINS WEBB SCREEN BEARINGS, BLUNGER BEARINGS, GENERAL STEEL MILL BEARINGS, GENERAL POWER PLANT BEARING LUBRICANT, TRAVELING SCREENS, DREDGING EQUIPMENT, SKI RESORT AND GOLF COURSE EQUIPMENT BEARINGS, ETC.



EXCELLENT CHOICE TO LUBRICATE PRECISION-TYPE BEARINGS, WHICH OPERATE UP TO 10,000 R.P.M.’S.


9992-TL TECHNICAL SPECIFICATIONS

9992-TL LUBRICANT COMPATIBILITY

NLGI GRADE 2TEXTURE SMOOTHCOLOR CREAM-WHITE

TEST ASTM METHOD TYPICAL RESULTS PENETRATION @ 77° F

UNWORKED D-217

276

ROLL STABILITY (% CHANGE) D-1831 293 (4.0) RUST PROTECTION D-1743 PASS

DROPPING POINT, ° F. D-D-2265 595

4 BALL E.P. PERFORMANCE LOAD WEAR INDEX

D-2596 72

TIMKEN O.K. LOAD, lbs., MIN. D-2509 85

WHEEL BEARING LIFE TEST, hrs D-3527 120

WATER WASHOUT @ 175° F., % D-1264 0.004

OIL SEPARATION, % LOSS D-1742 0.01 BASE OIL CHARACTERISTICS VISCOSITY @ 210° F., S.U.S.

D-2161

70

LOW TEMP TORQUE-WHEEL BEARING,

LOWEST OPERATIONAL

D-4693 - 40° F.

LOW DISPENSABLE / PUMPABLE GREASE MOBILITY TEST

U.S. STEEL METHOD - 40° F.

COMPATIBLE INCOMPATIBLE BORDERLINE BARIUM COMPLEX CALCIUM COMPLEX ALUMINUM COMPLEX

CALCIUM STEARATE BENTONE / CLAY CALCIUM 12-HYDROXY LITHIUM COMPLEX POLYUREA LITHIUM STEARATE

SILICA SODIUM LITHIUM 12-HYDROXY

CALCIUM SULFONATE COMPLEX

B-51 ALITHICON

HIGH TEMPERATURE BEARING LUBRICANT THE B-51 ALITHICON SYNTHETIC HIGH TEMPERATURE BEARING LUBRICANT IS SPECIFICALLY FORMULATED TO BE APPLIED WHERE CONVENTIONAL SOAP-THICKENED, OR SO CALLED NON-MELT GREASES, WILL NOT PROVIDE ADEQUATE PERFORMANCE. THE B-51 ALITHICON LUBRICANT IS A SYNTHETICALLY THICKENED GREASE WHICH EMPLOYS A HIGH THERMAL STABLE SYNTHETIC BASE FLUID, ALLOWING IT TO PROVIDE SUPERIOR LUBRICATION AND PROTECTION TO BEARINGS WHICH MUST OPERATE IN TEMPERATURES OF UP TO 700° F WITHOUT MELTING OR HARDENING IN SERVICE. TWO ADDITIONAL IMPORTANT FEATURES OF THE B-51 ALITHICON LUBRICANT IS: BEING WATERPROOF, RESISTING WATER WASH-OUT, AND HAVING A LONG SERVICE LIFE, REDUCING GREASE CONSUMPTION AS MUCH AS 800% WHEN COMPARED TO OTHER GREASES NORMALLY USED IN THESE APPLICATIONS. THE B-51 ALITHICON LUBRICANT HAS AN O.K. TIMKEN LOAD RATING OF 100 lbs, MINIMUM, AND WILL PRODUCE AND EXTENDED BEARING LIFE OF UP TO 400%. IT IS NOT NECESSARY TO LIMIT THE USE OF THE B-51 ALITHICON SYNTHETIC BEARING LUBRICANT ONLY TO BEARINGS OPERATING UNDER EXTREME TEMPERATURES OR WET CONDITIONS TO JUSTIFY THE ADDITIONAL COST. MANY LONG-TIME USERS OF THE B-51 ALITHICON LUBRICANT STATE THAT IT WAS PRIMARILY PURCHASED FOR USE IN THESE EXTREME, HIGH MAINTENANCE AREAS, BUT IT WAS LATER TRIED IN BEARINGS ON MACHINERY OPERATING IN AMBIENT TEMPERATURES AND UNDER AVERAGE CONDITIONS. BY REDUCING LUBRICANT CONSUMPTION, THE COST DIFFERENCE WAS JUSTIFIED. EXTRA PROFITS FROM THE USE OF THE B-51 ALITHICON LUBRICANT WAS GENERATED BY REDUCING LUBRICANT REPLACEMENT, LABOR COSTS, LESS MACHINERY DOWNTIME, AND INCREASED PRODUCTION. USER BENEFITS: * WITHSTANDS HIGH TEMPERATURES OF UP TO 700° F * WATERPROOF * EXTENDS BEARING LIFE OF UP TO 400% * WILL NOT MELT OR SLING FROM BEARINGS * REDUCES LUBRICANT CONSUMPTION OF UP TO 800% * EXCELLENT PUMPABILITY THROUGH CENTRALIZED LUBRICATION SYSTEMS * AN O.K. TIMKEN LOAD RATING OF 100 lbs, MINIMUM

FOR TYPICAL SPECIFICATIONS, TEST RESULTS, APPLICATIONS, AND COMPATIBILITY INFORMATION, SEE REVERSE SIDE



B-51 ALITHICON SYNTHETIC LUBRICANT INFORMATION

APPLICATIONS: DRY KILN FAN BEARINGS, SEALED FOR LIFE BEARINGS, STACK LOUVERS, COOKER BEARINGS, FLOTATION DRYER BEARINGS, TEXTILE MACHINERY, DOCTOR BEARINGS ON YANKEE DRYERS, ELECTRICAL GENERATING TURBINE LINKAGE BEARINGS, STOKER TRAVELING GRATE BEARINGS, AND MANY, MANY MORE.

BASE FLUID

AVAILABLE PACKAGING

LUBRICANT COMPATIBILITY



TYPICAL TEST DATA ASTM TEST B-51

NLGI GRADE 1

WORKED PENETRATION 305

PROLONGED WORKED PENETRATION,

% CHANGE

D-217 0.8

DROPPING POINT, MIN. D-566 NON-MELT

TEMPERATURE OPERATING RANGE

+28° F TO +700° F

TIMKEN O.K. LOAD, lbs, MIN. 2782 100


ROLL STABILITY, % CHANGE 1831 0.6

LEAKAGE TENDENCIES, % MAX. D-1264 0.1 WATER WASHOUT, % MAX.

38° C (100° F) 70° C (175° F)

D-1264 0.02 0.02

OXIDATION STABILITY, MAX. PRESSURE DROP @ 100 hrs., KPS

(PSI)

D-942 1

FOUR BALL METHOD, MAX. LOAD WHICH WELDING OCCURS kg (lbs)

D-2596 3.94

WEAR PREVENTATIVE CHARACTERISTICS, MAX. SCAR

DIAMETER 40 kg LOAD, 120 R.P.M.

D-2266 .2 mm


VISCOSITY CENTISTOKES, 40° C 150

VISCOSITY SUS @ 100° F 743 VISCOSITY SUS @ 210° F 78

VISCOSITY INDEX 160

* 30 - 14.5 oz TUBE CASE * 6 - 7.5 CAN CASE * 45 lb PAIL

* 120 lb KEG * 420 lb DRUM * BULK

ALUMINUM COMPLEX BARIUM COMPLEX CALCIUM STEARATE

CALCIUM 12-HYDROXY CALCIUM COMPLEX CALCIUM SULFONATE COMPLEX

BENTONE / CLAY LITHIUM COMPLEX LITHIUM STEARATE

ALITHICON C-155

SYNTHETIC BEARING LUBRICANT THE ALITHICON C-155 SYNTHETIC BEARING LUBRICANT IS SPECIFICALLY FORMULATED TO BE APPLIED WHERE CONVENTIONAL SOAP-THICKENED, OR SO CALLED NON-MELT GREASES, WILL NOT PROVIDE ADEQUATE PERFORMANCE. THE ALITHICON C-155 SYNTHETIC LUBRICANT IS A SYNTHETICALLY THICKENED GREASE WHICH EMPLOYS A HIGH THERMAL STABLE SYNTHETIC BASE FLUID, ALLOWING IT TO PROVIDE SUPERIOR LUBRICATION AND PROTECTION TO BEARINGS WHICH MUST OPERATE IN TEMPERATURES OF UP TO 700° F WITHOUT MELTING OR HARDENING IN SERVICE. TWO ADDITIONAL IMPORTANT FEATURES OF THE ALITHICON C-155 SYNTHETIC LUBRICANT IS: BEING WATERPROOF, RESISTING WATER WASH-OUT, AND HAVING A LONG SERVICE LIFE, REDUCING GREASE CONSUMPTION AS MUCH AS 800% WHEN COMPARED TO OTHER GREASES NORMALLY USED IN THESE APPLICATIONS. THE ALITHICON C-155 SYNTHETIC LUBRICANT HAS AN O.K. TIMKEN LOAD RATING OF 100 lbs, MINIMUM, AND WILL PRODUCE AND EXTENDED BEARING LIFE OF UP TO 400%. IT IS NOT NECESSARY TO LIMIT THE USE OF THE ALITHICON C-155 SYNTHETIC LUBRICANT ONLY TO BEARINGS OPERATING UNDER EXTREME TEMPERATURES OR WET CONDITIONS TO JUSTIFY THE ADDITIONAL COST. MANY LONG-TIME USERS OF THE ALITHICON C-155 SYNTHETIC LUBRICANT STATE THAT IT WAS PRIMARILY PURCHASED FOR USE IN THESE EXTREME, HIGH MAINTENANCE AREAS, BUT IT WAS LATER TRIED IN BEARINGS ON MACHINERY OPERATING IN AMBIENT TEMPERATURES AND UNDER AVERAGE CONDITIONS. BY REDUCING LUBRICANT CONSUMPTION, THE COST DIFFERENCE WAS JUSTIFIED. EXTRA PROFITS FROM THE USE OF THE ALITHICON C-155 SYNTHETIC LUBRICANT WAS GENERATED BY REDUCING LUBRICANT REPLACEMENT, LABOR COSTS, LESS MACHINERY DOWNTIME, AND INCREASED PRODUCTION. USER BENEFITS: * WITHSTANDS HIGH TEMPERATURES OF UP TO 700° F * WATERPROOF * EXTENDS BEARING LIFE OF UP TO 400% * WILL NOT MELT OR SLING FROM BEARINGS * REDUCES LUBRICANT CONSUMPTION OF UP TO 80% * EXCELLENT PUMPABILITY THROUGH CENTRALIZED LUBRICATION SYSTEMS * AN O.K. TIMKEN LOAD RATING OF 100 lbs, MINIMUM

FOR TYPICAL SPECIFICATIONS, TEST RESULTS, APPLICATIONS, AND COMPATIBILITY INFORMATION, SEE FOLLOWING PAGE



ALITHICON C-155 SYNTHETIC LUBRICANT INFORMATION APPLICATIONS: DRY KILN FAN BEARINGS, SEALED FOR LIFE BEARINGS, STACK LOUVERS, COOKER BEARINGS, FLOTATION DRYER BEARINGS, TEXTILE MACHINERY, DOCTOR BEARINGS ON YANKEE DRYERS, ELECTRICAL GENERATING TURBINE LINKAGE BEARINGS, STOKER TRAVELING GRATE BEARINGS, AND MANY, MANY MORE.

BASE FLUID

AVAILABLE PACKAGING


VISCOSITY CENTISTOKES, 40° C 1,400

VISCOSITY SUS @ 100° F 6,485 VISCOSITY SUS @ 210° F 463

VISCOSITY INDEX 160






LITHIUM 12-HYDROXY SILICA SODIUM POLYUREA

TYPICAL TEST DATA ASTM TEST C-155

NLGI GRADE 1.5 COLOR CLEAR

WORKED PENETRATION 305 PROLONGED WORKED PENETRATION, % CHANGE

D-217 0.8

DROPPING POINT, MIN. D-566 NON-MELT TEMPERATURE OPERATING RANGE

+28° F TO +700° F

TIMKEN O.K. LOAD, lbs, MIN. 2782 100 ACID RESISTANCE EXCELLENT ROLL STABILITY, % CHANGE 1831 0.6 LEAKAGE TENDENCIES, % MAX. D-1264 0.1 WATER WASHOUT, % MAX. 38° C (100° F) 70° C (175° F)

D-1264 0.02 0.02

OXIDATION STABILITY, MAX. PRESSURE DROP @ 100 hrs., KPS (PSI)

D-942 1


D-2596 3.94

WEAR PREVENTATIVE CHARACTERISTICS, MAX. SCAR DIAMETER 40 kg LOAD, 120 R.P.M.

D-2266 .2 mm


ALITHICON C-155

SYNTHETIC BEARING LUBRICANT THE ALITHICON C-155 SYNTHETIC BEARING LUBRICANT IS SPECIFICALLY FORMULATED TO BE APPLIED WHERE CONVENTIONAL SOAP-THICKENED, OR SO CALLED NON-MELT GREASES, WILL NOT PROVIDE ADEQUATE PERFORMANCE. THE ALITHICON C-155 SYNTHETIC LUBRICANT IS A SYNTHETICALLY THICKENED GREASE WHICH EMPLOYS A HIGH THERMAL STABLE SYNTHETIC BASE FLUID, ALLOWING IT TO PROVIDE SUPERIOR LUBRICATION AND PROTECTION TO BEARINGS WHICH MUST OPERATE IN TEMPERATURES OF UP TO 700° F WITHOUT MELTING OR HARDENING IN SERVICE. TWO ADDITIONAL IMPORTANT FEATURES OF THE ALITHICON C-155 SYNTHETIC LUBRICANT IS: BEING WATERPROOF, RESISTING WATER WASH-OUT, AND HAVING A LONG SERVICE LIFE, REDUCING GREASE CONSUMPTION AS MUCH AS 800% WHEN COMPARED TO OTHER GREASES NORMALLY USED IN THESE APPLICATIONS. THE ALITHICON C-155 SYNTHETIC LUBRICANT HAS AN O.K. TIMKEN LOAD RATING OF 100 lbs, MINIMUM, AND WILL PRODUCE AND EXTENDED BEARING LIFE OF UP TO 400%. IT IS NOT NECESSARY TO LIMIT THE USE OF THE ALITHICON C-155 SYNTHETIC LUBRICANT ONLY TO BEARINGS OPERATING UNDER EXTREME TEMPERATURES OR WET CONDITIONS TO JUSTIFY THE ADDITIONAL COST. MANY LONG-TIME USERS OF THE ALITHICON C-155 SYNTHETIC LUBRICANT STATE THAT IT WAS PRIMARILY PURCHASED FOR USE IN THESE EXTREME, HIGH MAINTENANCE AREAS, BUT IT WAS LATER TRIED IN BEARINGS ON MACHINERY OPERATING IN AMBIENT TEMPERATURES AND UNDER AVERAGE CONDITIONS. BY REDUCING LUBRICANT CONSUMPTION, THE COST DIFFERENCE WAS JUSTIFIED. EXTRA PROFITS FROM THE USE OF THE ALITHICON C-155 SYNTHETIC LUBRICANT WAS GENERATED BY REDUCING LUBRICANT REPLACEMENT, LABOR COSTS, LESS MACHINERY DOWNTIME, AND INCREASED PRODUCTION. USER BENEFITS: * WITHSTANDS HIGH TEMPERATURES OF UP TO 700° F * WATERPROOF * EXTENDS BEARING LIFE OF UP TO 400% * WILL NOT MELT OR SLING FROM BEARINGS * REDUCES LUBRICANT CONSUMPTION OF UP TO 80% * EXCELLENT PUMPABILITY THROUGH CENTRALIZED LUBRICATION SYSTEMS * AN O.K. TIMKEN LOAD RATING OF 100 lbs, MINIMUM




ALITHICON C-155 SYNTHETIC LUBRICANT INFORMATION APPLICATIONS: DRY KILN FAN BEARINGS, SEALED FOR LIFE BEARINGS, STACK LOUVERS, COOKER BEARINGS, FLOTATION DRYER BEARINGS, TEXTILE MACHINERY, DOCTOR BEARINGS ON YANKEE DRYERS, ELECTRICAL GENERATING TURBINE LINKAGE BEARINGS, STOKER TRAVELING GRATE BEARINGS, AND MANY, MANY MORE.

BASE FLUID

AVAILABLE PACKAGING


VISCOSITY CENTISTOKES, 40° C 1,400

VISCOSITY SUS @ 100° F 6,485 VISCOSITY SUS @ 210° F 463

VISCOSITY INDEX 160






LITHIUM 12-HYDROXY SILICA SODIUM POLYUREA

TYPICAL TEST DATA ASTM TEST C-155

NLGI GRADE 1.5 COLOR CLEAR

WORKED PENETRATION 305 PROLONGED WORKED PENETRATION, % CHANGE

D-217 0.8

DROPPING POINT, MIN. D-566 NON-MELT TEMPERATURE OPERATING RANGE

+28° F TO +700° F

TIMKEN O.K. LOAD, lbs, MIN. 2782 100 ACID RESISTANCE EXCELLENT ROLL STABILITY, % CHANGE 1831 0.6 LEAKAGE TENDENCIES, % MAX. D-1264 0.1 WATER WASHOUT, % MAX. 38° C (100° F) 70° C (175° F)

D-1264 0.02 0.02

OXIDATION STABILITY, MAX. PRESSURE DROP @ 100 hrs., KPS (PSI)

D-942 1


D-2596 3.94

WEAR PREVENTATIVE CHARACTERISTICS, MAX. SCAR DIAMETER 40 kg LOAD, 120 R.P.M.

D-2266 .2 mm





OG-7000 SEMI-SYNTHETIC OPEN GEAR LUBRICANT (NLGI-2)

ALITHICON "OG-7000" SEMI-SYNTHETIC OPEN GEAR LUBRICANT WAS FORMULATED, TESTED, AND HAS BEEN PROVEN TO BE THE PREFERRED LUBRICANT FOR USE TO LUBRICATE OPEN GEARS FOUND ON MINING AND CONSTRUCTION EQUIPMENT. PLUS ALL TYPES OF INDUSTRIAL MACHINERY. THE ALITHICON "OG-7000" IS LEAD-FREE, TOTALLY WATERPROOF, AND WITHSTANDS HIGH TEMPERATURES. IT GREATLY REDUCES LUBRICANT CONSUMPTION AND RE-LUBRICATION INTERVALS, FOR THE ALITHICON "OG-7000" WILL NOT MELT, RUN, OR SLING OFF OPEN GEARS. THE ALITHICON "OG-7000 HAS UNIFORMLY DISPERSED, LOW-FRICTION INGREDIENTS, GIVING IT A HIGH FILM STRENGTH WITH HEAVY LOAD CARRYING CHARACTERISTICS, GREATLY REDUCED STARTING TORQUE, AND IS EXCELLENT FOR USE AT LOWER OPERATING TEMPERATURES. IT CAN BE APPLIED BY HAND OR PRESSURE GUN. THE ALITHICON "OG-7000" RECOMMENDED TEMPERATURE RANGE IS -5° F TO 565° F. USER BENEFITS: * TOTALLY WATERPROOF

* WITHSTANDS HIGH TEMPERATURES (565° F)

* EXCELLENT FOR USE IN LOW TEMPERATURES (-5° F)

* WILL NOT CHIP OR FLAKE AT LOW TEMPERATURES

* CUSHIONS AND REDUCES OPEN GEAR NOISES

* REDUCES LUBRICANT CONSUMPTION AS MUCH AS 200%

* GREATLY EXTENDS OPEN GEAR LIFE

* O.K. TIMKEN LOAD, 80 lbs, MINIMUM APPLICATIONS: EXPOSED GEARS OF ALL TYPES: STEAM AND POWER WINCHES, HOST, POWER SHOVELS, DREDGES, ROLLER GEARS, SHOVEL GEARS, WALKING MECHANISMS, DIPPERSTICKS, TREE SHAKERS, DRAWING MACHINERY, KILN GEARING, TRUCK-TRACTOR FIFTH WHEELS, SLOW-MOVING BEARINGS, WIRE ROPE AND CABLES, ELEVATOR TRACKS, ETC.



OG-7000 SEMI-SYNTHETIC OPEN GEAR LUBRICANT (NLGI-2)

BASE FLUID INFORMATION

AVAILABLE PACKAGING


NLGI GRADE 2

COLOR BLACK

TEXTURE TACKY

WORKED PENETRATION, ASTM 273

TIMKEN O.K. LOAD 80

OXIDATION STABILITY, AFTER 500 hrs DROP 6

OIL SEPARATION I.P. LEAKAGE, 7 DAYS @ 104° F 1.2

SOLUBILITY - BOILING WATER INSOLUBLE

VISCOSITY S.S.U. @ 100° F 2,465

VISCOSITY S.S.U. @ 210° F 167

VISCOSITY INDEX 134

FLASH POINT, ° F 590

FIRE POINT, ° F 680

GRAVITY, A.P.I. 26

OXIDATION INHIBITOR YES

E.P. ADDITIVE YES

RUST INHIBITOR YES

POUR POINT, ° F -10

* 50 / 11.5 oz CAULKING TUBE CASE * 120 lb KEG

* 45 lb PAILS * 420 lb DRUM

COMPATIBLE INCOMPATIBLE

CALCIUM STEARATE CALCIUM 12-HYDROXY

SILICA BENTONE / CLAY

ALUMINUM COMPLEX BARIUM COMPLEX CALCIUM COMPLEX CALCIUM SULFONATE COMPLEX LITHIUM STEARATE LITHIUM 12-HYDROXY LITHIUM COMPLEX POLYUREA SODIUM



7702 ALITHICON SYNTHETIC HI-TEMP BEARING LUBRICANT (NLGI - 2)

7702 ALITHICON SYNTHETIC HI-TEMP BEARING LUBRICANT IS SPECIFICALLY FORMULATED TO BE APPLIED WHERE CONVENTIONAL SOAP THICKENED, OR CO-CALLED NON-MELT, CLAY THICKENED GREASES WILL NOT PROVIDE ADEQUATE PERFORMANCE. 7702 ALITHICON SYNTHETIC HI-TEMP BEARING LUBRICANT IS FORMULATED WITH AN INORGANIC COPOLYMER BASE, A SYNTHETIC BASE OIL, SOUTHEAST OIL'S EXCLUSIVE WEAR REDUCING ADDITIVE "ALITHICON", ALONG WITH A SOLIDIFIED SECONDARY LUBRICANT. 7702 WILL STAY IN THE BEARING OR LUBRICATED SURFACES, PROVIDING CONSTANT PROTECTION WHERE ORDINARY GREASES WILL MELT, RUN, OR HARDEN. EVEN AFTER TEMPERATURES ARE REACHED THAT WOULD CAUSE THE SYNTHETIC BASE OIL TO VOLATILE, A SECONDARY "DRY FILM" LUBRICANT REMAINS, PROVIDING ADEQUATE PROTECTION OF UP TO 1,600° F.

USER BENEFITS:

* NON-MELTING * LESS LUBRICANT CONSUMED * PROTECTION UP TO 1,600° F * EXTENDS BEARING LIFE UP TO 300% * WITHSTANDS AND PROTECTS UNDER EXTREMELY HIGH TEMPERATURES

APPLICATIONS:

7702 HAS BEEN DESIGNED TO BE USED IN APPLICATIONS SUCH AS: SOAKING PIT COVERS, SOAKING PIT CRANES, ANNEALING PIT FURNACES, KILN CAR WHEELS, LADLE BEARINGS, OVEN CONVEYOR BEARINGS, HOMOGENIZER BEARINGS, ETC.

CHANGE OVER INFORMATION:

NOTICE: DIFFERENT GREASES MAY NOT MIX. TO BE SAFE, ALWAYS FLUSH BEARINGS AND BEARING FEED LINES UNTIL COMPLETELY FILLED WITH 7702 ALITHICON SYNTHETIC HI-TEMP BEARING LUBRICANT.

FOR TYPICAL SPECIFICATIONS AND TEST RESULTS, SEE REVERSE SIDE.





7702 ALITHICON BEARING LUBRICANT


* 50 - 14.5 oz TUBES CASE * 120 lb KEG * 45 lb PAIL * 420 lb DRUM * BULK

NLGI GRADE 2 PENETRATION (ASTM D-217), WORKED 260 - 265

TEXTURE TACKY MELTING POINT, ° F NON-MELTING TIMKEN O.K. LOAD, lbs., MIN. 80

COLOR SILVER BASE OIL VISCOSITY, SUS @ 210° F FLASH POINT FIRE POINT VISCOSITY INDEX

124 596 669 160

ALITHICON 452000-FM FOOD MACHINERY BEARING LUBRICANT (NLGI-00)

THE ALITHICON 452000-FM FOOD MACHINERY BEARING LUBRICANT IS DESIGNED TO MEET TODAY’S DEMANDING REQUIREMENTS OF THE MODERN FOOD PROCESSING EQUIPMENT, WHICH OPERATES UNDER EXTREMELY HIGH TEMPERATURES, HEAVY LOADS, HIGH SPEED, AND WET CONDITIONS. IT ALSO MEETS WITH THE FDA / USDA PURITY REQUIREMENTS WITH AN H-1 RATING FOR INCIDENTAL CONTACT WITH THE FOOD PRODUCTS BEING PROCESSED. THE ALITHICON 452000-FM FOOD MACHINERY BEARING LUBRICANT IS FORMULATED TO PERFORM IN A SUPERIOR MANNER WITH THE FOLLOWING OUTSTANDING FEATURES: A BROAD OPERATING RANGE (-10° F TO 550° F), WATERPROOF, MECHANICAL STABILITY (RESISTANCE TO HARDENING OR SOFTENING IN SERVICE), RUST AND OXIDATION RESISTANCE, AND HEAT REVERSION CHARACTERISITICS OR REVERSABILITY (THE ABILITY TO MAINTAIN ITS ORIGINAL CONSISTENCY AFTER BEING HEATED AND COOLED REPEATEDLY). WITH THE AVAILABILITY OF THE ALITHCON 452000-FM FOOD MACHINERY BEARING LUBRICANT, IT IS NOT NECESSARY TO SETTLE FOR SHORT BEARING LIFE, DECREASED PRODUCTION, AND EXCESSIVE EQUIPMENT REPAIRS JUST TO MEET WITH THESE USDA / FDA PURITY REQUIREMENTS. USER BENEFITS: ♦ TOTALLY WATERPROOF ♦ WITHSTANDS HIGH TEMPERATURES OF UP TO 550° F ♦ PREVENTS RUSTING IN BEARINGS ♦ RATES AN O.K. TIMKEN LOAD OF 80 lbs, MIN. ♦ MEETS THE FDA / USDA REQUIREMENTS OF H-1 FOR PURITY ♦ TACKY - REDUCES LUBRICANT CONSUMPTION AS MUCH AS 300% ♦ EXTENDS BEARING LIFE AS MUCH AS 400%

CHECK THIS ALITHICON LUBRICANT FOR USDA APPROVAL, FOR USE IN FOOD PROCESSING PLANTS IN THE 2002 NSF WHITE BOOK (NSF INTERNATIONAL / NON-FOOD COMPOUNDS) AT

www.nsf.org/usda



APPLICATIONS: ALL FOOD MACHINERY APPLICATIONS REQUIRING AND NLGI-00 LUBRICANT. EXCELLENT LUBRICANT TO LUBRICATE COUPLINGS, WHICH OPERATE BETWEEN 1 - 5,000 R.P.M.’S. ALITHICON 452000-FM FOOD MACHINERY LUBRICANT TYPICAL SPEFICATIONS:

AVAILABLE PACKAGING: ♦ 35 lb PAILS ♦ 45 lb PAILS ♦ 120 lb KEG ♦ 420 lb DRUM ♦ BULK 452000-FM LUBRICANT COMPATIBILITY

SPECIFICATION TEST RESULT

NLGI GRADE 00

WORKED PENETRATION, 60 STROKES (ASTM D-217) 410

DROPPING POINT, MINIMUM (ASTM D-566) 550

LUBRICATING OPERATING RANGE -10° TO 550° F

TIMKEN O.K. LOAD, lbs, MINIMUM 80


COLOR SNOW WHITE

TEXTURE SLIGHTLY TACKY

EVAPORATION LOSS @ 350° F, WT. % (ASTM D-2595) 0.9

USP SYNTHETIC HYDROCARBON BASE OIL VISCOSITY @ 40° C 100

BASE FLUID VISCOSITY INDEX 120

COMPATIBLE INCOMPATIBLE BORDERLINE

CALCIUM 12-HYDROXY LITHIUM COMPLEX SILICA ALUMINUM COMPLEX

BARIUM COMPLEX CALCIUM STEARATE CALCIUM COMPLEX BENTONE / CLAY LITHIUM STEARATE LITHIUM 12-HYDROXY POLYUREA

CALCIUM SULFONATE COMPLEX



ALITHICON OG-3000 E.P. PARA/SYNTHETIC OPEN GEAR LUBRICANT (AGMA 11 E.P.)

THE ALITHICON OG-3000 E.P. PARA/SYNTHETIC OPEN GEAR OIL HAS BEEN DESIGNED, AND FORMULATED, TO LUBRICATE OPEN GEARS, WHICH OPERATE IN TEMPERATURES OF FROM +25° F TO UP TO 200° F. WITH THE ALITHICON OG-3000 E.P. PARA/SYNTHETIC OPEN GEAR LUBRICANT, BEING ABSENT FROM ANY TYPE OF SOLIDS, CONCERNS DUE TO LUBRICANT APPLICATION EQUIPMENT PLUGGING ARE ELIMINATED. THE ALITHICON OG-3000 E.P., BEING A PARA/SYNTHETIC FLUID CAN BE USED, AND IS RECOMMENDED FOR USE TO DISPERSE THROUGH LUBRICANT DELIVERY SYSTEMS DESIGNED TO PUMP 9 E.P., 11 E.P., AND 13 E.P. OPEN GEAR LUBRICANTS. THE CO-ADHESIVENESS OF THIS LUBRICANT WILL, NOT ONLY REDUCE LUBRICANT CONSUMPTION BY 50%, IT IS FORMULATED TO REDUCE WEAR, EXTENDING OPEN GEAR LIFE OF UP TO 500%.

USER BENEFITS:

WITHSTANDS TEMPERATURES OF UP TO 200° F. EXCELLENT PERFORMANCE AT LOW TEMPERATURES TIMKEN O.K. LOAD, 80 lbs., MIN. ELIMINATES LUBRICANT DELIVERY SYSTEM PLUGGING CLEANER AND A MORE SATISFACTORY OPEN GEAR LUBRICANT TO WORK WITH REDUCES LUBRICANT CONSUMPTION BY 50% EXTENDS OPEN GEAR LIFE OF UP TO 500% LONGER

APPLICATIONS:

OPEN GEARS FOUND ON PAPER MILL WOODYARD MACHINERY, CHEMICAL MANUFACTURING MACHINERY AND ALL OPEN GEARS REQUIRING LUBRICATION WITH A HEAVY FLUID.

SEE REVERSE SIDE FOR TECHNICAL SPECIFICATIONS, TEST RESULTS AND AVAILABLE PACKAGING



ALITHICON OG-3000 E.P. PARA/SYNTHETIC OPEN GEAR LUBRICANT (AGMA 11 E.P.)


* 35 lbs PAIL * 45 lbs PAIL * 120 lbs KEG * 420 lbs DRUM * 2,500 lb DISPOSABLE TOTE TANK * BULK

TEST RESULTS

ISO GRADE 3,000

AGMA GRADE 11 E.P. VISCOSITY, Cst @ 40° C (ASTM D-0445) 3,000

VISCOSITY, Cst @ 100° C (ASTM D-0445) 129

VISCOSITY INDEX (ASTM D-2270) 101

FLASH POINT, coc, ° F. (ASTM D-0092) 620

POUR POINT, ° F. (ASTM D-0097) +15

API GRAVITY (ASTM D-4052) 20.1

TIMKEN O.K. LOAD, lbs., MIN. (ASTM 2782) 80

COLOR (ASTM D-1500) 8 (DARK AMBER)



ALITHICON 4500 SPECIAL LUBRICANT

THE ALITHICON 4500 SPECIAL LUBRICANT IS FORMULATED TO ENSURE THE FLEXIBILITY OF ROLLER CHAINS, ENSURING SMOOTH OPERATION, KEEPING CHAINS FROM JUMPING SPROCKETS AND GREATLY REDUCING BREAKAGE. ROUGH CHAIN OPERATION INCREASES POWER CONSUMPTION. PREMATURE WEAR SHORTENS CHAIN AND SPROCKET LIFE, WHICH CAUSES RAPID CHAIN "STRETCHING", A CRITICAL FAILURE IN MACHINES WHERE MACHINERY SYNCHRONIZATION IS A CHAIN FUNCTION. WHEN APPLIED TO ROLLER CHAINS, THE ALITHICON 4500 SPECIAL LUBRICANT READILY PENETRATES INTO THE PINS AND BUSHINGS, REDUCING WEAR AND EXTENDING CHAIN AND SPROCKET LIFE UP TO 400% LONGER THAN THE MORE COMMONLY USED LUBRICANTS. BEING WATERPROOF, WATER AND STEAM DO NOT TEND TO WASH IT OFF, AND RUST AND CORROSION ARE ELIMINATED. THE ALITHICON 4500 IS A TACKY, WATERPROOF, DRIPLESS, HIGH TEMPERATURE (WITHSTANDING 580° F) LUBRICANT, MAKING IT UNMATCHED IN PERFORMANCE AS A CHAIN LUBRICANT. THE ALITHICON 4500 SPECIAL LUBRICANT IS THE PREFERRED LUBRICANT, TO LUBRICATE WHEEL BEARINGS, WHICH ARE NORMALLY LUBRICATED WITH AN 85w/140 GEAR OIL. THE ALITHICON 4500 SPECIAL LUBRICANT WILL EXTEND WHEEL BEARING LIFE OF UP TO 400% LONGER, WHILE ELIMINATING SEAL SEAPAGE.

USER BENEFITS: * WATERPROOF * EASY TO APPLY * WITHSTANDS HIGH TEMPERATURES AS MUCH AS 580° F * WILL NOT SLING OR DRIP * ENSURES A SAFER, QUIETER OPERATION * ELIMINATES RUST AND CORROSION * VIRTUALLY ELIMINATES CHAIN STRETCHING * EXTENDS CHAIN, SPROCKET, AND CABLE LIFE UP TO 400% * EXTENDS WHEEL BEARING LIFE OF UP TO 400% * ELIMINATES WHEEL BEARING SEAL LEAKS APPLICATIONS: READY-MIX CONCRETE TRUCK MIXING DRUM GEAR REDUCERS, ALL ROLLER CHAINS, CABLES, SLOW SPEED ENCLOSED GEAR REDUCERS, OIL FILLED WHEEL BEARINGS, SEMI-TRUCK TRAILER DOLLY GEARINGS, ROTARY MOWER GEAR REDUCERS, CONSTRUCTION EQUIPMENT SEALED TRACK ROLLERS, LUMBER MILL FETCHER SHAFTS, HOUR GLASS CONVEYOR CHAINS, PLANETARY GEARS, PLUS MANY MORE. METHOD OF APPLICATIONS: SQUIRT CAN, PAINT BRUSH, FREE POURING, GREASE GUN, GEAR OIL PUMP, OR A CENTRALIZED LUBRICATING SYSTEM.

SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS.





ALITHICON 4500 SPECIAL LUBRICANT TYPICAL SPECIFICATIONS AND TEST RESULTS

ALITHICON 4500 SPECIAL LUBRICANT WHEEL BEARING

BENCH TEST RESULTS: PHASE 1: WHEEL HUBS WERE FILLED WITH THE ALITHICON 4500 SPECIAL LUBRICANT. THE BEARINGS WERE LOADED TO 1,000 lbs OF TEST WEIGHT AND ROTATED FOR 150 MINUTES (2.5 HOURS), OR APPROXIMATELY 100 ROAD MILES. TEST END OPERATING TEMPERATURES WERE RECORDED: 84° F. PHASE 2: AT THE END OF THE WHEEL BEARING TEST: PHASE #1, THE WHEEL BEARING RESERVOIR WAS DRAINED OF THE ALITHICON 4500 SPECIAL LUBRICANT, LEAVING THE LUBRICANT WHICH COATED THE BEARINGS. THE BEARINGS WERE LOADED TO 1,000 lbs WEIGHT AND ROTATED FOR 450 MINUTES (7.5 HOURS) OR APPROXIMATELY 300 MILES. TEST END OPERATING TEMPERATURES WERE RECORDED, 85° F. AFTER DISASSEMBLY, BEARINGS SHOW NO MEASURABLE SIGNS OF WEAR.

4500 LUBRICANT COMPATIBILITY COMPATIBLE INCOMPATIBLE


* 45 lb (6 GALLON) PAIL

* 120 lb (16 GALLON) KEG * 420 lb (55 GALLON DRUM

NLGI GRADE 00 WORKED PENETRATION 425 PROLONGED WORKED PENETRATION (ASTM D-217), % CHANGE

0

DROPPINT POINT, MIN. (ASTM D-566), ° F. 580 TIMKEN O.K. LOAD, lbs, MIN. (ASTM 2782) 80 ACID RESISTANCE EXCELLENT ROLL STABILITY (ASTM D-1831), % CHANGE 0.01 LEAKAGE TENDENCIES, % MAX. (ASTM D-1264) 0 WATER WASHOUT, % MAX. (ASTM D-1264) 30° C. (100° F.) 79° C. (175° F.)

0.01

0.012 OXIDATION STABILITY, MAX. (ASTM D-942) PRESSURE DROP @ 100 hrs, KPS (PSI)

2

FOUR BALL METHOD, MAX. OAD WHICH WELDING OCCURS, kg (lbs) (ASTM D-2266)

2.96

WEAR PREVENTATIVE CHARACTERISTICS (ASTM D-2266), MAX SCAR DIAMETER 40 kg LOAD, 1200 R.P.M.

1 mm

DENSITY, lbs PER GALLON 7.5 COPPER STRIP CORROSION (ASTM D-130) 1 A (PASS) COLOR BRONZE

CALCIUM STEARATE ALUMINUM COMPLEX BARIUM COMPLEX BENTONE / CLAY CALCIUM COMPLEX CALCIUM SULFONATE COMPLEX

CALCIUM 12-HYDROXY LITHIUM STEARATE LITHIUM 12-HYDROXY SILICA LITHIUM COMPLEX POLYUREA SODIUM

ALITHICON GASOLINE & DIESEL FUEL IMPROVER

THE PREFERRED FUEL TREATMENT FOR BOTH GASOLINE AND DIESEL FUEL

A MODERN DIESEL FUEL TREATMENT, MEETING THE NEW E.P.A. LOW SULFUR REQUIREMENTS, WITHOUT SACRIFICING EQUIPMENT PERFORMANCE.

REGULATION BY THE E.P.A. MANDATE THAT ALL DIESEL FUELS INTENDED FOR ON-HIGHWAY USE MUST HAVE A LOW SULFUR CONTENT. CURRENT FUELS HAVE A SULFUR LEVEL OF ABOUT 0.25%, WHILE NEW FUELS ARE REQUIRED TO HAVE A 0.05% MAXIMUM. IN ORDER TO REDUCE THE SULFUR LEVEL TO VALUES OF 0.05% AND LESS, A REFINING PROCESS CALLED “HYDROTREATING” IS UTILIZED. THIS PROCESS ALTERS THE MATERIAL BY CHANGING SOME OF THE AROMATIC COMPOUNDS TO SATURATES, WHICH CAUSES THE PROBLEMS. IT IS THE REMOVAL OF THE POLYAROMATICS, NITROGEN, AND SULFUR COMPOUNDS THAT IS REDUCING TH PROPER BOUNDARY LUBRICATION, BETWEEN THE LOADED MOVING PARTS. INSPECTIONS OF THE FAILED SYSTEMS (PREDOMINATELY, ROTARY FUEL PUMPS) HAS DEMONSTRATED THE INCREASE IN SCUFFING WEAR. UNFORTUNATELY, REDUCING THE SULFUR CONTENT IN DIESEL FUEL COULD CAUSE AN IMPACT ON THE FUEL ECONOMY BECAUSE THERE SEEMS TO BE A REDUCTION IN THE BTU/GALLON OF ABOUT 10%. THEREFORE, THE REDUCED LEVEL COULD CAUSE AN INCREASE IN FUEL CONSUMPTION. THE ALITHICON GASOLINE & DIESEL FUEL IMPROVER IS FORMULATED TO ENSURE MAXIMUM PERFORMANCE AND LESS ENGINE WEAR, PROVIDING LONGER ENGINE LIFE WITH LESS MAINTENANCE AND DOWNTIME. THE ALITHICON GASOLINE & DIESEL FUEL IMPROVER BREAKS A DROP OF WATER INTO, APPROXIMATELY 1 MILLION PARTS, ABSORBING IT THROUGH-OUT THE DIESEL FUEL , WHICH ALLOWS THE WATER TO PASS THROUGH THE COMBUSTION PROCESS, IN PARTICLES SO SMALL, THE PERFORMANCE OF THE ENGINE IS NOT AFFECTED.

USER BENEFITS: * EASIER ENGINE STARTING * GREATLY EXTENDS ROTARY FUEL PUMP LIFE * INCREASED POWER PERFORMANCE * MORE SATISFACTORY ENGINE IDLING * REDUCES ALGAE GROWTH * REDUCES DIESEL FUEL POUR POINT * ELIMINATES FUEL INJECTOR NOZZLE PLUGGING * PROVIDES WATER PROTECTION - ABSORBS MOISTURE * INCREASES CETANE RATING AS MUCH AS 15% * INCREASES MILES PER GALLON AS MUCH AS 10% * REDUCES BLACK EXHAUST SMOKE TO A LIGHT GRAY HAZE

SEE REVERSE SIDE FOR TYPICAL SPECIFICATIONS.



ALITHICON GASOLINE & DIESEL FUEL IMPROVER

TYPICAL SPECIFICATIONS AND TEST RESULTS


* 24 / 1 QUART CASE * 6 / 1 GALLON CASE

* 6 GALLON PLASTIC PAIL * 55 GALLON DRUM

TREATMENT RATIO: ONE GALLON OF ALITHICON DIESEL FUEL IMPROVER TREATS 500 GALLONS OF GASOLINE OR DIESEL FUEL. ON THE INITIAL TREATMENT, IT IS SUGGESTED TO MIX ONE GALLON OF ALITHICON GASOLINE & DIESEL FUEL IMPROVER TO 100 GALLONS OF GASOLINE OR DIESEL FUEL TO ENSURE A CLEAN FUEL SYSTEM. (1) OUNCE OF ALITHICON GASOLINE AND DIESEL FUEL IMPROVER TREATS (3) GALLONS OF GASOLINE OR DIESEL FUEL.



FLASH POINT, ° F. (ASTM D-92) 119

CORROSION TEST (ASTM D-665) PASS

VARNISH & GUM TEST (ASTM D-189) PASS

POUR POINT, ° F. - 70

SPECIFIC GRAVITY, DEGREES, API 27.5

VISCOSITY SUS @ 100° F. 54.1

VISCOSITY SUS @ 32° F. 296

VISCOSITY SUS @ 0° F. 1205

ACID NEUTRALIZER TEST EXCELLENT

MOISTURE ABSORBTION TEST EXCELLENT

COLOR LIGHT AMBER

ALITHICON 767 CHAIN, CABLE, OPEN-GEAR,

& BEARING AEROSOL LUBRICANT THE ALITHICON 767 AEROSOL LUBRICANT IS AN EXCELLENT LUBRICANT DESIGNED FOR USE TO LUBRICATE ROLLER CHAINS, CABLES, OPEN-GEARS, WORKING MECHANISMS, AND BEARINGS. IT IS A TACKY LUBRICANT, WHICH IS EASY TO APPLY, RESISTS WATER WASH-OFF, AND WITHSTANDS TEMPERATURES OF UP TO 540° F WITHOUT MELTING OR DRIPPING. THE ALITHICON 767 AEROSOL LUBRICANT IS OUR 2212 BEARING LUBRICANT, WHICH HAS BEEN THINNED WITH HEPTANE AND PRESSURIZED IN AN AEROSOL CAN FOR EASY APPLICATION. WHEN THE ALITHICON 767 LUBRICANT IS APPLIED TO ROLLER CHAINS, THE EXTREMELY THIN LUBRICANT WILL PENETRATE INSTANTLY INTO THE PINS AND BUSHINGS, THEN IN APPROXIMATELY 180 SECONDS, THE SOLVENTS WILL EVAPORATE, LEAVING EACH CHAIN LINK LUBRICATED FROM THE INSIDE OUT. THE ALITHICON 767 LUBRICANT WILL ELIMINATE CHAIN LINK FREEZING AND CHAIN SPROCKET JUMPING. ROLLER CHAINS AND CHAIN SPROCKET LIFE ARE EXTENDED OF UP TO 500% WHEN PROPERLY USING THE 767. THE ALITHICON 767 AEROSOL LUBRICANT PENETRATES INSIDE CABLES, THEN DRIES TO AN NLGI-2 GREASE, LUBRICATING EACH STRAND, AND CABLE LIFE IS GREATLY EXTENDED. WHEN THE ALITHICON 767 AEROSOL LUBRICANT IS USED TO LUBRICATE OPEN GEARS AND HARD-TO-REACH WORKING MECHANISMS, IT REACTS IN THE SAME MANNER. IT COATS THE SURFACES, THEN DRIES TO A LIGHT-WEIGHT GREASE, OFFERING A PROTECTIVE CUSHION, THUS GREATLY REDUCING WEAR.

USER BENEFITS: * EASY TO APPLY * RESISTS WATER WASH-OFF * RATES AN O.K. TIMKEN LOAD OF 70 lbs., MIN. * RESISTS THE ATTRACTION OF LINT, DIRT, OR DUST * GREATLY REDUCES WEAR AND EXTENDS EQUIPMENT LIFE * FREE OF HEXANE

APPLICATIONS: ROLLER CHAINS, CABLES, OPEN GEARS, WORKING MECHANISMS, SLIDING SURFACES, MOTOR GRADER CIRCLES, PIVOT POINTS, BEARINGS, ETC.



ALITHICON 767 CHAIN, CABLE, OPEN-GEAR,

& BEARING AEROSOL LUBRICANT

TYPICAL SPECIFICATIONS AND TEST RESULTS: ABSENCE OF VOLATILE INGREDIENTS

AVAILABLE PACKAGING: 12 / 16.22 fl oz CAN CASE



PRODUCT CODE 767

NLGI GRADE 2

WORKED PENETRATION 269

PROLONGED WORKED PENETRATIONS (ASTM D-217), % CHANGE

< 1.5

DROPPING POINT, MIN. (ASTM D-566) NONE

TIMKEN O.K. LOAD, lbs, MIN. (ASTM 2782) 70


ROLL STABILITY (ASTM D-1831), % CHANGE 1.1

LEAKAGE TENDENCIES, % MAX. (ASTM D-1263) 0.2

WATER WASHOUT, % MAX. (ASTM D-12640) 39° C (100° F) 79° C (175° F)

1.9 4.3

OXIDATION STABILITY, MAX. (ASTM D-942) PRESSURE DROP @ 100 hrs, KPS (PSI)

3

FOUR BALL METHOD, MAX. LOAD WHICH WELDING OCCURS 2.76

WEAR PREVENTATIVE CHARACTERISTICS (ASTM D-2666) MAX., SCAR DIAMETER 40 kg LOAD, 1200 R.P.M.

0.425 mm

COLOR RED

BASE OIL: VISCOSITY SUS @ 100° F VISCOSITY CTS @ 100° F VISCOSITY SUS @ 210° F VISCOSITY CTS @ 210° F VISCOSITY INDEX

693 149 77

17.1 110



ALITHICON P-88 ROLLER CHAIN & PENETRATING LUBRICANT

THE ALITHICON P-88 IS FORMULATED FOR USE TO LUBRICATE ROLLER CHAINS FOUND ON FARM AND INDUSTRIAL MACHINERY WHERE NORMALLY USED ROLLER CHAIN LUBRICANTS ATTRACT DIRT AND OTHER ABRASIVES, CREATING AN ABRASIVE COMPOUND WHICH EXCELERATES WEAR AND SHORTENS CHAIN LIFE. THE ALITHICON P-88 ROLLER CHAIN LUBRICANT WILL NOT ATTRACT DIRT AND ABRASIVES AND WILL EXTEND ROLLER CHAIN LIFE OF UP TO 400%. THE ALITHICON P-88 DISSOLVES AND PENETRATES RUST. IT IS THE PREFERRED CHOICE TO USE TO LOOSEN RUSTY BOLTS AND NUTS. THE ALITHICON P-88 DISPLACES MOISTURE. JUST SPRAY PARTS OR SURFACES, WAIT A FEW MINUTES, AND WIPE OFF WITH A CLOTH. RESPRAY FOR LONG-TERM PROTECTION. THE ALITHICON P-88 IS AN EXCELLENT QUICK-START SPRAY, REPLACING ETHER, TO AID IN CRANKING DIFFICULT-TO-START DIESEL ENGINES. THE ALITHICON P-88 WILL NOT VAPOR LOCK DIESEL ENGINES, AS DOES ETHER. * EXTENDS ROLLER CHAIN LIFE OF UP TO 400% * WILL NOT ATTRACT DIRT AND ABRASIVES * DISSOLVES AND PREVENTS RUST * DISPLACES MOISTURE * CONTAINS TEFLON * PENETRATES RUST TO LOOSEN RUSTY BOLTS & NUTS * A DIESEL ENGINE QUICK START SPRAY - REPLACING ETHER * MEETS WITH USDA / FDA H-2 REQUIREMENTS WHEN USING THE ALITHICON P-88 TO LUBRICATE ROLLER CHAINS, CHAIN FREEZING AND CRIMPING, AND CHAIN SPROCKET JUMPING IS ELIMINATED. AS A RESULT, ROLLER CHAIN AND SPROCKET LIFE IS GREATLY EXTENDED. MANUFACTURED

UNDER ISO 9001 CERTIFIED STANDARD



ALITHICON FM-555 AEROSOL FOOD MACHINERY CHAIN AND PENETRATING FLUID

THE ALITHICON FM-555 AEROSOL FOOD MACHINERY CHAIN AND PENETRATING LUBRICANT IS NON-TOXIC, PENETRATES, LUBRICATES, REDUCES WEAR, AND ELIMINATES RUSTING. IT IS SPECIFICALLY FORMULATED TO EFFECTIVELY REDUCE THE WEAR OF ROLLER CHAINS, PIVOT POINTS, AND BEARINGS FOUND ON FOOD PACKAGING AND PROCESSING EQUIPMENT, WHICH OPERATE UNDER TEMPERATURES OF FROM -100° F TO 500° F. IT TOTALLY REJECTS WATER AND THE EFFECTS OF STEAM. THE ALITHICON FM-555 AEROSOL FOOD MACHINERY CHAIN AND PENETRATING LUBRICANT IS COLORLESS AND ODORLESS, IS AUTHORIZED BY USDA, WITH AN H-1 RATING, FOR USE IN FEDERALLY INSPECTED MEAT AND POULTRY PLANTS, AND IT ALSO COMPLIES WITH FDA TITLE 21, PART 178, SECTION 178.3570 AND PART 172, SECTION 172.878. IT IS APPROVED FOR USE WHERE THE INCIDENTAL CONTACT WITH FOOD, EDIBLE PRODUCTS IS POSSIBLE. THE ALITHICON FM-555 AEROSOL FOOD MACHINERY CHAIN AND PENETRATING LUBRICANT DOES NOT CONTAIN ANY OZONE-DEPLETING CHLORINATED SOLVENTS. USER BENEFITS: * EASY TO APPLY * OUTSTANDINGLY REDUCES WEAR * ELIMINATES RUSTING * REJECTS WATER AND STEAM * OPERATING TEMPERATURE RANGE OF -100° F TO 500° F * PENETRATES AND DISSOLVES CORROSION * GREATLY EXTENDS ROLLER CHAIN AND BEARING LIFE THE ALITHICON FM-555 AEROSOL FOOD MACHINERY CHAIN AND CABLE LUBRICANT HAS PROVEN TO BE THE PREFERRED CHOICE LUBRICANT FOR THE FOLLOWING APPLICATIONS: ROLLER CHAINS * BEARINGS * CABLES * CASTERS * CONVEYORS * SHACKLES, SLIDES, MIXERS, GRINDERS, STRETCH WRAPPERS, DEBONERS, BREAST PROCESSORS, TROLLEY AND TROLLEY BRACKETS, FROZEN MEAT BREAKERS, HATCHING TRAYS, POULTRY PICKERS, PUSH CARTS, SPICE MIXERS, AND MANY, MANY MORE APPLICATIONS FOUND IN THE FOOD INDUSTRY.

FOR TYPICAL SPECIFICATIONS AND TEST RESULTS, SEE REVERSE SIDE



AVAILABLE PACKAGING: 12 / 12 oz CANS / AEROSOL CASE

ALITHICON FM-555 AEROSOL FOOD MACHINERY CHAIN AND PENETRATING FLUID


SPECIFICATIONS ASTM TEST

RESULTS

U.S.D.A., AUTHORIZED H-1 VISCOSITY @ 100° F @ 210° F

D-88 D-88

155 45

VISCOSITY INDEX D-567 150

POUR POINT, ° F D-2500 -100 FLASH POINT, ° F D-92 565 FIRE POINT, ° F D-92 605

TURBINE RUST TEST D-665 PASS OXIDATION STABILITY, hrs D-943 9000+

TIMKEN, O.K. LOAD, lbs, MIN. D-2782 80 FOUR BALL E.P. TEST LOAD WEAR INDEX SEIZURE WELD

D-2596 60

110 180

fleet synthetic enclosed gear & transmission · agma lubricant number 2 ep 3 ep 4 ep 5 ep 6 ep...

Documents