engine air cleaners, service parts and accessoriesengine air cleaners, service parts and accessories...

132
ENGINE AIR CLEANERS, SERVICE PARTS AND ACCESSORIES DONALDSON DELIVERS CLEAN AIR WHEN YOUR ENGINE NEEDS IT MOST

Upload: others

Post on 28-Feb-2020

13 views

Category:

Documents


0 download

TRANSCRIPT

ENGINE AIR CLEANERS, SERVICE PARTS AND ACCESSORIES DONALDSON DELIVERS CLEAN AIR WHEN YOUR ENGINE NEEDS IT MOST

Enhance

Protect

Improve

Our innovative products are

solving complex filtration

challenges that improve

people's lives, enhance engine

and equipment performance

and protect our environment.

Donaldson has the technical

expertise, superior customer

support and vast network of

locations around the world to

meet your toughest filtration

needs - from initial system

design through replacement

products.

IntroductionInvented by Donaldson . . . . . . . . . . . . . . . . . . . . . . 2Our Customers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Simple Facts on Air Filtration . . . . . . . . . . . . . . . . 10Air Cleaner Models by Flow Direction . . . . . . . . 125 Easy Steps to Air Cleaner Selection . . . . . . . . 14Air Cleaner Selection Chart . . . . . . . . . . . . . . . . . 16Conversion Factors . . . . . . . . . . . . . . . . . . . . . . . . 17

Air Cleaner Models

PowerCore® SeriesPSD (Medium to Heavy Dust) . . . . . . . . . . . . . . . 19PSD Service Instructions . . . . . . . . . . . . . . . . . . . 34

Light DustDuraLite™ ECB, ECC, ECD . . . . . . . . . . . . . . . . . . 38DuraLite Service Instructions . . . . . . . . . . . . . . . 42EPB-ERB2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 EPB-ERB2 Service Instructions. . . . . . . . . . . . . . 48

Medium DustFKB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50FKB Service Instructions . . . . . . . . . . . . . . . . . . . 54XRB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55XRB Service Instructions . . . . . . . . . . . . . . . . . . . 59EPB-ERB2 with Full-View Pre-Cleaner. . . . . . . . 60EPB-ERB2 with TopSpin™ Pre-Cleaner . . . . . . . 62FPG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64FPG Alexin™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70FPG + FPG Alexin™ Service Instructions . . . . . 76 FPG + FPG Alexin™ Mounting Bands. . . . . . . . . 77FTG Cycloflow™ . . . . . . . . . . . . . . . . . . . . . . . . . . . 78FTG Service Instructions . . . . . . . . . . . . . . . . . . . 81FRG2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82FRG2 Service Instructions . . . . . . . . . . . . . . . . . . 88

Heavy DustFLB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 FLB Service Instructions . . . . . . . . . . . . . . . . . . . 92EPB-ERB2 with Donaspin™ Pre-Cleaner . . . . . 93EPB-ERB2 with Strata™ Pre-Cleaner . . . . . . . . 95SPB2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97SRB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100SPB2-SRB Service Instructions . . . . . . . . . . . . 103SSG Donaclone™ . . . . . . . . . . . . . . . . . . . . . . . . 104 SSG Service Instructions . . . . . . . . . . . . . . . . . . 110 STG Donaclone™ . . . . . . . . . . . . . . . . . . . . . . . . . 111STG Service Instructions . . . . . . . . . . . . . . . . . . 117

AccessoriesClamps, Worm-Drive Hose & T-Bolt . . . . . . . . . 120Clamps, SealClamps™ . . . . . . . . . . . . . . . . . . . . 121Drop Down Tube Extension (Dust Dumpa) . . . 122Exhaust Ejectors . . . . . . . . . . . . . . . . . . . . . . . . . 124In-Line Check Valve . . . . . . . . . . . . . . . . . . . . . . . 126In-Line Separators . . . . . . . . . . . . . . . . . . . . . . . . 127Moisture Skimmer & Eliminator . . . . . . . . . . . . 128Mounting Bands, Metal . . . . . . . . . . . . . . . . . . . 129Pre-Cleaners, DonaSpin™ . . . . . . . . . . . . . . . . . 130Pre-Cleaners, Full-View . . . . . . . . . . . . . . . . . . . 131Pre-Cleaners, TopSpin™ . . . . . . . . . . . . . . . . . . . 132Rain Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134Restriction Indicators . . . . . . . . . . . . . . . . . . . . . 135Rubber Elbows, Humps & Reducers . . . . . . . . 137Silicone Charge Air Connectors . . . . . . . . . . . . 140Vacuator™ Valves . . . . . . . . . . . . . . . . . . . . . . . . 141

Maintenance And ServicingAir Filter Cleaning . . . . . . . . . . . . . . . . . . . . . . . . 144Air Filter Inspection . . . . . . . . . . . . . . . . . . . . . . . 145General Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

Service Parts . . . . . . . . . . . . . . . . . . . . . . . 147

Parts Listing . . . . . . . . . . . . . . . . . . . . . . . . 153

Engine Air Cleaners,Accessories & Service Parts

For a variation or a custom designed intake system, please call

your current supplier of Donaldson products.

Table of Contents

Ultra-Web fibers have submi-cron diameters and small interfiber spaces, which result in more contami nant being captured on the surface of the media and low restriction.

Cellulose fibers are larger than Ultra-Web fibers, and have larger spaces between the fibers, causing contami-nant to load in the depth of the media and plug the airflow path; resulting in higher restriction and less capacity.

Ultra-Web® and Cellulose Media at Same Magnification

Red circles represent the diameter of a 2 micron and a 5 micron particle. Cellulose media is used in most air filters.

Manufactured to PerformDesigned to Fit

... solve complex filtration challenges that improve people's lives, enhance engine and equipment performance and protect our environment.

Ultra-Web® Nanofiber Filtration TechnologyDonaldson has developed Ultra-Web media for usage in applications that operate in the highest level of protection.

Ultra-Web media, a web-like filtering layer applied over specially-formulated cellulose media, traps submicron contaminant on the surface of the filter. This surface loading

prevents the contaminant from dispersing throughout the media and substantially increases the filter's efficiency. In field test, filters using Ultra-Web technology hold up to five times more contaminant compared to cellulose air filters

Ultra-Web® Nanofiber Filtration Technology - a proven filter media with over 25 years in heavy-duty air filtration applications!

Scanning Electron Microscope image of Ultra-Web media magnified 1000 times.

Over 90 million m² Ultra-Web media sold

2 Engine Air Cleaners, Accessories & Service Parts

Engine Air Cleaners, Accessories & Service Parts 3

PSD PowerCore® Air Cleaners, Peak performance in Half the Space

Air cleaners with original PowerCore filtration technology offer maximum design flexibility. You gain equal performance in significantly less space, freedom to design unique configurations to fit tight spots, and overall design simplicity.

See the PSD PowerCore® air cleaner section for all the details.

PowerCore® G2 Filtration Technology Big Performance, Small Footprint

The second generation of Donaldson PowerCore Filtration Technology is now available for engine air intake systems. PowerCore G2 Filtration Technology offers size reduction and geometric flexibility to overcome the tight space constraints resulting from today's complex emissions systems. In addition to size reduction, its customizable filtration performance also features lower restriction and longer filter life. For more information on PowerCore G2, please contact your Donaldson representative.

Manufactured to PerformDesigned to Fit

... solve complex filtration challenges that improve people's lives, enhance engine and equipment performance and protect our environment.

PSD08, PSD09, PSD10 and PSD12 housings

Conventional Cellulose Air Cleaner

Original PowerCore® Air Cleaner 60% smaller than A

30% smaller than B

A B C NEW

RadialSeal™ Sealing Technology The best, most reliable choice for your engine

Filters using Donaldson RadialSeal Technology are lighter weight and easier to service than other filter designs. Invented by Donaldson in the 1980s, the urethane seal compresses radially on the outside surface of the outlet tube to create a seal around the tube. In most applications, a safety element inside the main element seals radially to the inside of the outlet tube to provide an extra measure of protection. Filters equipped with RadialSeal Technology are easy to replace and provide leak-free seal even in adverse operating contitions such as extreme heat or cold.

Manufactured to PerformDesigned to Fit

... solve complex filtration challenges that improve people's lives, enhance engine and equipment performance and protect our environment.

New XRB Housings: left XRB08; middle XRB12; and right XRB10 (filters shown from XRB12 model).

FKB Housings and Filters: top center, FKB06; bottom left, FKB05; and bottom right, FKB04

XRB Air Cleaners Smaller, Lightweight Alternative Two-Stage Air Cleaner

The XRB family is ideal for light- to medium-duty diesel engine trucks, agriculture, construction, mining and industrial engine applications. The XRB air cleaner is smaller, lighter and easier to install and it effectively reduces contaminants, providing a high level of engine protection. Available in three diameter sizes.

See the XRB air cleaner section for all the details.

FKB Air Cleaners Smaller, Lightweight Alternative Two-Stage Air Cleaner

For smaller sizes of the XRB family, check out the FKB air cleaner family.

See the FKB air cleaner section for all the details.

er

inenesier

NEW

r NEW

4 Engine Air Cleaners, Accessories & Service Parts

Engine Air Cleaners, Accessories & Service Parts 5

Manufactured to PerformDesigned to Fit

... solve complex filtration challenges that improve people's lives, enhance engine and equipment performance and protect our environment.

Donaldson Endurance™ high efficiency air filters, made using Donaldsons advanced Ultra-Web® nanofiber technology, deliver cost saving benefits:

• Longer filter life with submicron contaminant• Ideal for extended maintenance intervals• Longer engine life• Lower operating costs

Go Twice the Distance with Donaldson Endurance™ Air Filters

Donaldson Endurance™ air filters are available for many popular Donaldson air cleaner housing models. Filters with Ultra-Web technology are easily to recognized because of the blue filter media.

Finding a Donaldson Endurance air filter in this catalogue. If available for an air cleaner model, the Endurance air filters are listed in the service parts list with ES, Extended Service and HE, High Efficiency.

New Dust Dumpa ship fully assembled. Left: Part No. X006561 / Part No. X006562 right.

Drop Down Tube Extension (Dust Dumpa) Replacement to Your Existing Dust Cup Assembly

Air cleaners operate in extreme dust conditions (mining, construction and quarrying). In some cases, the dust is so concentrated that maintenance personnel have to empty the dust cups or check the Vacuator™ Valves more frequently than they like.

These two new drop tube accessory incorporates rubber connections that improve dust evacuation from the housing during normal vehicle vibration. The clear tube allows you to easily see what's happening during daily inspections without climbing up to open or check out the Vacuator Valve.

Available for SSG and PSD PowerCore® air cleaner and also works on all other air cleaners with 76 mm drop tube.See the Accessories Section for more details.

NEW

SSG PSD

Manufactured to PerformDesigned to Fit

Don't forget Intake Accessories

Engine Air Accessories are designed to solve our customer's specific problems - such as excessive moisture or noise - or simply help maintain your systems.

• Inlet Hoods - protect air intake from large debris • Pre-cleaners - extend air filter life and boost system efficiency • Filter Gauges and Indicators - maximize filter life and reduce

maintenance costs • Rubber Elbows and Connectors - minimize air intake flow

resistance, reduce noise levels in severe operating condition • Vacuator™ Valves - automatically dispel dust and water from the

air cleaner • Stack Caps - protects the exhaust stack from water and debris.

See the Accessories Section for all the details.

Donaldson TopSpin™ Pre-Cleaner Extend Filter Life in Heavy Dust Conditions

We recently upgraded the cover material of the TopSpin Pre-Cleaner to increase impact resistance. Before it was a see-through unit, now it is black.

This new design will even more extend your primary air filter life, boost your system efficiency and extend your engine life!

Donaldson TopSpin requires no maintenance and works great on all types of equipment, from crawler tractors to farm tractors to skid steer loaders.

See the Accessories Section for all the details.

... solve complex filtration challenges that improve people's lives, enhance engine and equipment performance and protect our environment.

Spin it was a

IMPROVED

6 Engine Air Cleaners, Accessories & Service Parts

Engine Air Cleaners, Accessories & Service Parts 7

Manufactured to PerformDesigned to Fit

... solve complex filtration challenges that improve people's lives, enhance engine and equipment performance and protect our environment.

A New Generation of Hybrid Air Cleaners featuring Donaldson's Unique Design Concept

Air Cleaners equipped with Donaldson's Unique Design Concept ensure you

1) The best protection for your Engine:

Via a unique fit of the element into the access cover, • rotation of the element is prevented which improves durability of the radial seal.The unique interface between the primary element • and access cover assures best fit and function and is achieved only with the Donaldson original elements, discouraging use of low quality will-fit elements.New moulded polymer closed end cap works in • conjunction with the element retention system resulting in outstanding durability and safer manipulation of your element. A plastic liner outer instead of a metal one prevents • media pleat tip wear and improves handling protection.

2) The best protection for our Environment:

Reduced metal content. •

See the ERB2, FRG2 and SPB2 Air Cleaner Section for more details on these next generation products.

NEW

sign

UNIQUEDESIGNCONCEPT

ERB2

SPB2

FRG2

Patent Pending for Donaldson's Unique Design Concept.

Agco, Case New Holland, Claas, Deutz, Fendt, John Deere, Landini, Manitou, Massey Ferguson, McCormick, Renault Agriculture, SAME, Valtra...

BMC, Carrier Transicold, DAF, Daimler, EvoBus, FIAT, Ford Otosan, Freightliner, International, Isuzu, Iveco, MAN, Paccar, Renault Truck, Scania, Thermo-King, Vanhool, VDL Bus, Volvo...

AtlasCopco, Bobcat, Case New Holland, Caterpillar, Daewoo, Doosan, Dynapac, Fermec, Fiat-Kobelco, Furukawa, Hitachi, JCB, Komatsu, Liebherr, Linde, MCFE, Merlo, Sandvik, Terex, Toyota, Volvo CE...

Manitou, Hyster, JCB, Jungheinrich, Komatsu, Linde, Toyota...

Caterpillar, Cummins, Detroit Diesel, Honda, Isuzu, Iveco, John Deere, KHD, Komatsu, Kubota, MAN Engines, Mercedes Benz, Perkins, Scania, Sisu, Steyr Motors, Yanmar Diesel...

Manufactured to PerformDesigned to Fit

the following customers rely on Donaldson

8 Engine Air Cleaners, Accessories & Service Parts

Aftermarket Warranty

Brochure No. F116006 (11/08)

Donaldson warrants its Aftermarket products against failure due to defects in materials and workmanship for the period specified under Terms and Conditions for the particular product.

Donaldsons obligation under this warranty cov-ers replacing the failed product, including trans-portation charges, only. If the Donaldson product failure is the sole and direct cause of damage to the equipment on which the product was proper-ly installed, Donaldson will reimburse reasonable costs to restore the equipment to the condition it was in immediately before the failure.

This warranty does not cover failure due to mis-application, misuse, abuse, neglect, rust through and corrosion (mufflers), improper service prac-tices or non-Donaldson approved modifications. Engine and equipment manufacturers’ warran-ties remain in effect when Donaldson products are used.

Donaldson must be notified in writing of any claims covered by this warranty within one year of the date of failure. Donaldson, at its discre-tion, will either physically visit the site where the alleged failure has been found or, request that all parts, Donaldson and other relevant parts, be shipped prepaid to its General Office, in care of the Product Lab or as otherwise specified.

Terms & ConditionsWarranty coverage begins at the date of installa-tion to the original end-user, and expires after the indicated period or kilometres, whichever occurs first.

More detailed information can be found in the Donaldson Europe Operating Guide or can be received upon request.

Warranty Length by ProductFiltration Products Warranty Period

Air Cleaner Housing & Accessories 1 yearLiquid Filter Assemblies & Accessories 1 yearAir & Liquid Filters Maximum 1 year

Exhaust Products Warranty Period

Exhaust Assemblies On-Road 2 years - 300.000 kilometersExhaust Assemblies Off-Road 1 year - 1500 working hoursExhaust Accessories 1 year

Donaldson Engine

for Filtration and Exhaust Products

Engine Air Cleaners, Accessories & Service Parts 9

10 Engine Air Cleaners, Accessories & Service Parts

Why an Air Intake System?

Air is a critical component of combustion for a diesel engine. If the air reaching the engine is not clean, the engine will lose efficiency and have engine wear. The engine will run longer and more efficiently with a proper air intake system that is designed to keep the engine intake air as clean as possible by removing par-ticulate matter or debris that would cause engine wear and ultimately failure.

Components Air Intake System

Air Cleaner Types

One-Stage Air Cleaners

Air Cleaners in which the air goes through the inlet and directly to the main element are considered one-stage air cleaners. One-stage air cleaners are typically used where there is less contaminate in the environment, such as in on-road applications.

Two-stage Air Cleaners

Air entering a two-stage air cleaner is first pre-cleaned before reaching the main element. The air may either be sent through pre-cleaner tubes or cleaned by centrifugal flow around the filter. Depending on the type of pre-cleaner, the pre-cleaner removes between75-98% of the contaminate from the air before the air reaches the main element. Two stage air cleaners are recommended for use in medium- and heavy dust environments, such as in agricultural, construction, and mining applications.

Element types

Main ElementIs the filter element in the air cleaner that removes around 99,9%+ of the air's dust. The air flows through the main element first.

Safety ElementIs an optional element that protects the engineduring servicing of the main element and in case of a leak in the main element.

Inlet Stack

Bellow

Clean Air Duct

Air Cleaner

Mounting Band

Vacuator™ Valve

on Air FiltrationSimple Facts

... common terms and definitions.

inleted one-

e in the

Main Element

Safety Element

Technologies

RadialSeal™RadialSeal refers to Donaldsons sealing technology, which uses the urethane end caps and the cleaners outlet tube to created the seal. This is the preferred method of sealing.

Axial SealThe Axial Seal sealing method requires a force between air filter and air cleaner that provides enough compression on the gasket between the parts to create a seal.

Filtration Terms

Dust CapacityDust capacity is the amount of contaminant that will be collected on a filter before final restriction level - as set by the engine manufacturer - is reached.

EfficiencyEfficiency is the percentage of dust that the air cleaner with a filter removed from intake air. Donaldson air cleaners have a 99,7% efficiency level.

RestrictionRestriction represents the resistance to the flow of air through the air cleaner system. Typical unit is kilopascal (kPa). Air cleaners with clean filters should have restrictions between 0,5 and 4 kPa.

Filter mediaFilter media is the material in the filter that removes the contaminate. Conventional media is made from cellulose fibers combined with resins to keep the fibers together.

Dust ConcentrationDust concentration expresses the mass of dust in a specified volume of air. Typical ambient conditions are around 0,1 milligrams per cubic meter (mg/m³). Dirt road conditions are around 10 miligrams per cubic meter (mg/m³).

Laboratory LifeThis is the life of an air filter, until a defined restriction, tested at a constant dust concentration (mg/m³) following an ISO 5011 laboratory test procedure to determine performance and allow comparison with other air filter models.

Field LifeThis is the life of an air filter, till a defined final restriction, during its usage in the field.

Differential PressureThe difference in pressure between two points, generally between the inlet and outlet of an air cleaner. To be measured in pascal (Pa).

PascalThe SI unit to express a pressure, to be used instead of mm H2O.Pa (pascal) - kPa (kilopascal) - mbar (milibar) -daPa (decapascal)

1 mm H2O = 9,80665 Pa 1000 Pa = 1 kPa 100 Pa = 1 mbar 10 Pa = 1 daPa

Airflow RequirementsAir is as critical to the operation of an engine as it is to the working of the human body. Like lungs, an engine draws air from the atmosphere. The amount of air required by engine depends on the type of engine, whether there is a turbocharger, and the amount of horsepower of the engine. The airflow requirement is a specification of the engine that should be given by the engine manufacturer.

on Air FiltrationSimple Facts

... common terms and definitions.

Engine Air Cleaners, Accessories & Service Parts 11

NEW

B Airflow

Air in the Side, Out the End

Light Dust - ECCDisposable, one-stage, dry air cleaner, small, lightweight and unitized (housing and filter in one). For small 2-3 cylinder, high-vibration engines. Can be vertically or horizontally mounted. Handles airflows of 1-26,5 m³/min. Used on off-road equipment operating in medium-dust conditions. Page 38-42.

C Airflow

Air in the End, Out the Same End

Light Dust - ECBDisposable, one-stage, dry air cleaner, small, lightweight and unitized (housing and filter in one). For 2-3 cylinder, high-vibration engines. Can be vertically or horizontally mounted. Handles airflows of 6-90 m³/min. Used on light-duty applications. Page 38-42.

Donaldson has air cleaner housings that work in a variety of dust conditions and air flow patterns (A - D, and G). For improved filtration reliability and quicker filter service compared to older axial seal style air cleaners, Donaldson recommends installing either PowerCore air cleaners or radial seal style air cleaners whenever possible.

Flow Direction Legend

B = Air in the Side, Out the End

C = Air in the End, Out the Same End

D = Air in the End, Out the Opposite End

G = Air in the Side, Out the End

by Flow DirectionAir Cleaner Selection

Light and Medium Dust - FKBA compact housing high dust holding capacity, and comparable airflow to FPG. Two-stage filtration, side inlet, horizontal installation. Body diameters in 4", 5” and 6". Mount under hood or behind cab. Handles airflows from 2-6 m³/min. Used on off-road equipment operating in medium-dust conditions. Page 50-54.

Moairfroacon

NEW

Medium Dust - XRBThe radial seal, plastic, two-stage air cleaner. with side inlet for horizontal installation. Body diameters in 8", 10" and 12". Mount under hood or behind cab. Handles airflows of 7,5-18 m³/min. Used on off-road equipment operating in medium-dust conditions. Page 55-59.

Light, Medium & Heavy Dust - EPBOne-stage full-plastic air cleaner. Body diameters in 7" and 8". Handles airflows of 2-7 m³/min. Used on light-, medium- and heavy-duty applications, always combined with a pre-cleaner. Page 43-48.

Heavy Dust - FLBTwo-stage air cleaner with scavenge exhaust system. Body diameters in 6", 8", 10" and 12". Handles airflows of 3-17 m³/min. Designed for heavy-duty equipment. To be used with an exhaust ejector. Page 90-92.

Heavy Dust - SPB2Two-stage full-plastic air cleaner with built-in high efficiency pre-cleaner. Body diameter of 13". Handles airflows of 6-22 m³/min. Designed for heavy-duty equipment. To be used with an exhaust ejector. Page 97-99.

Light, Medium & Heavy Dust - ERB2 One-stage hybrid air cleaner. Body diameters in 10", 11", 13" and 15". Handles airflows of 8-65 m³/min. Used on light-, medium- and heavy-duty applications, always combined with a pre-cleaner. Page 43-48.

Heavy Dust - SRBTwo-stage hybrid air cleaner with built-in high efficiency pre-cleaner. Body diameters in 9", 10", 11" and 13". Handles airflows of 4-18 m³/min. Designed for heavy-duty equipment. To be used with an exhaust ejector. Page 100-103.

12 Engine Air Cleaners, Accessories & Service Parts

UNIQUE DESIGN CONCEPT

LighDispos

Designused wQUEUEE

IGNNN NCEPPTPTTT NEW

UNIQUE DESIGN CONCEPT

diameairflomediualwayPage

QUEUEE IGNNN

CEPPTPTTT NEW

Light Dust - ECDDisposable, one-stage, dry air cleaner, small, lightweight and unitized (housing and filter in one). For small 2-3 cylinder, high-vibration engines. Can be vertically or horizontally mounted. Handles airflows of 1-23 m³/min. Used on light-duty applications. Page 38-42.

D Airflow

Air in the End, Out the Opposite End

G Airflow

Air in the Side, Out the End

Medium Dust - FPGThe first fully plastic air cleaner in our two-stage filtration line. Built-in pre-cleaner. Tangential inlet, with or without safety element, body diameters from 4", 5", 7", 8" and 10". Handles airflows of 0,5-12 m³/min. Can be mounted horizontal, vertical or at an angle. Used on medium-duty applications. Page 64-69 / 76-77.

Medium to Heavy Dust - FRG2 Two-stage hybrid air cleaner which is available in body diameters of 10", 11", 13", 15" and 18". Horizontal mount required. Handles airflows from 6,5-51 m³/min. Used in medium- to heavy-duty duty applications. Page 82-88.

Heavy (Severe) Dust - STGTwo-stage - high airflow - air cleaner with built-in Donaclone™ tube pre-cleaner. Two styles available - one with a peripheral inlet and another with a tubular inlet. Handles airflows from 11-50 m³/min. Can be mounted vertically or horizontally. Used on heavy-duty applications. Page 111-117.��������

Medium to Heavy Dust - PSDTwo-stage air cleaner with built-in high efficiency pre-cleaner using the PowerCore™ Filtration Technology. Smaller, compact with built-in mounting brackets. Can be vertically or horizontally mounted. Handles airflows of 6-30 m³/min. Body diameters in 8", 9", 10" and 12". Designed for medium- and heavy-duty equipment. Can be used with Vacuator™ Valve on the pre-cleaner or continuously scavenge of the pre-cleaner by an exhaust ejector or air blower cooling. Page 19-35.

NEW

Medium Dust - Alexin FPGTwo-stage full-plastic air cleaner with built-in pre-cleaners. Tangential inlet, with or without safety element, body diameters from 6", 8", 9" and 10". Handles airflows of 1,5-12 m³/min. Can be mounted horizontal, vertical or at an angle. Used on medium-duty applications. Page 70-77.

Heavy (Severe) Dust -SSGThese new models are replacing our older SRG models. Donaldson's largest two-stage engine air cleaner, designed for the engines on large equipment. Handles airflows of 48-135 m³/min. The best protection for 500 to 2000 horsepower diesel engines. This new model uses radial seal sealing technology for filter retention. Used on heavy-duty applications. Page 104-110.

nteh

NEW

Medium to Heavy Dust - FTGTwo-stage air cleaner with built-in pre-cleaner. Body diameter of 21". Handles airflows of 32-59 m³/min. Used in medium- to heavy-duty duty applications. Page 78-81.

Engine Air Cleaners, Accessories & Service Parts 13

UNIQUE DESIGN CONCEPT

HUa

QUEUEE IGNNN

CEPPTPTTT NEW

14 Engine Air Cleaners, Accessories & Service Parts

Additional Consideration

1. Please be aware that when you have High Pulsation engines the air inflow to the air cleaner is influenced by this pulsation. We recommand that you review the application and if necessary multiply the airflow - found by one of above formula - by the pulsation factor (PF).

2. No pulsation factor needs to be considered for turbo charged engines.

3. Donaldson ECB, ECC, ECD Duralite™ (see page 38-42) and the FPG057505 Air Cleaners (see page 67) are not subject to the pulsation factor due to the fact that we use a specially developed High Pulsation media for these products.

ExampleA tractor is equiped with a 40 HP(SAE), 3 cylinder, 4 stroke natural aspirated diesel engine of 2 litres run-ning at 2600 RPM.

Formula A = Airflow = 2 x 2600 x 0,85 = 2,21 m³/min. 1000 x 2

Formula B = Airflow = 40 x 0,057 = 2,28 m³/min.

In High Pulsation application multiply your answer by FP table which in this caseis 2,21 m³/min. x 1,2 = 2,652 m³/min.

There are 2 different formulas to estimate the airflow (m³/min) required by the engine.

One formula is based on Engine Displacement (Formula A). The other is based on Engine Horse Power (Formula B).

Formula A = Airflow = Engine Displacement x RPM x VE = m³/min. 1000 x CF

Formula B = Airflow = HP(SAE) x SA = m³/min.

Engine Displacement• Size of the engine expressed in litres (swept volume).

RPM = Revolutions per minute• VE = Volumetric Efficiency•

CF = Cycle Factor = 2 for 4 stroke engine• 1 for 2 stroke engine

HP(SAE) = Horse Power• SA = Specific Airflow per Horse Power•

PF Table2,1 for 1 cylinder engine natural aspirated.1,5 for 2 cylinder engine natural aspirated.1,2 for 3 cylinder engine natural aspirated.1,0 for 4 and more cylinder engine natural aspirated.

Air Cleaner SelectionFive Easy Steps to

(1) Determine the Airflow Requirements of the Engine

VE Table0,85 for 4 stroke natural aspirated diesel engine1,60 for 4 stroke turbo charged diesel engine1,85 for 4 stroke turbo charged after cooled diesel engine1,40 for 2 stroke scavenge blower diesel engine1,90 for 2 stroke turbo charged diesel engine

SA Table0,057 m³/min. for 4 stroke natural aspirated diesel engine0,065 m³/min. for 4 stroke turbo charged/after cooled engine0,093 m³/min. for 2 stroke scavenge blower diesel engine0,102 m³/min. in for 2 stroke turbo charged diesel engine

For example, a truck of less than 8 ton will probably see light-dust, whereas dumpers used on construction sites would almost always be surrounded by an extremely heavy-dust concentration of large dirt particles. To deter-mine the type of environment and the dust concentration level your machine works in, you can use the table below.

You can do this by using the Air Cleaner Selection Overview on page 12-13. This correlates the Airflow Requirements of your engine (which you calculated under step 1) with the Dust Concentration level of your envi-ronment (which you calculated under step 2).

Environment Applications Dust concentration (mg/m³)

Light-Duty On-Highway Trucks (< 8T), Lift Truck, 1-5 (On-Road, Marine) Pumps for use in generators, compressors, marine, small engines and railroad. + carbon, soot, oil vapeur

Medium-Duty Mixed operating Trucks (8 -16T), 5-15 (Light Construction, Farm Tractor, Lift Truck, Agricultural, Compressors) Mobile Compressor, Skid Steer.

Medium- to Heavy-Duty Combines and Harvesters, Earth 15-20 Moving Equipment, Loader, Dozer, Grader, Excavator, Artic Dumper.

Heavy-Duty Scraper, Dumper, Track type dozer, (Construction, Mining) Mining Equipment, 20-50 Rail Road (Middle East).

Extra Heavy-Duty Special equipment, Military. 50-100

Note: These figures are only indications.

(2) Determine the Type of Machine and its Environment

(3) Select an Air Cleaner Series

Air Cleaner SelectionFive Easy Steps to

Once you have selected your Air Cleaner Series you can look in the catalogue for the specific Air Cleaner Model according to the Air Flow Requirements your engine needs. You can do this by refering to the Air Flow Restriction Curves. If there are 2 air cleaner models that fit your parameters, choose the one with the lowest restriction to ensure maximum service life from that air cleaner seriers.

(4) Choose a SPECIFIC Air Cleaner Model

(5) Choose Intake AccessoriesAccessories are an integral and important part of the entire air intake filtration system. See the Accessories Section for more details.

Engine Air Cleaners, Accessories & Service Parts 15

...Donaldson offers a full line of air cleaners for a wide variety of applications and operating environments

Engine Protection for All Dust Conditions

16 Engine Air Cleaners, Accessories & Service Parts

13

5.0

0

EPB-ERB2 with TopSpin™ Pre-Cleaner: RadialSeal

EPB-ERB2 with Strata™ Pre-Cleaner: RadialSeal

FRG2: RadialSeal

FPG + FPG Alexin: RadialSeal

FTG: Axial Seal

FLB: Axial Seal

SPB2-SRB: RadialSeal

SSG: RadialSeal

STG: Axial Seal

PSD: PowerCore®

PSD: PowerCore®

FKB: RadialSeal

XRB: RadialSeal

1

.00

2

.00

4

.00

6

.00

7

.00

8

.50

11

.00

14

.00

1

8.2

0

23

.00

32

.00

39

.00

3

5.0

0

46

.00

51

.00

5

7.0

0

6

5.0

0

8

0.0

0

97

.00

1

15

.00AIRFLOW 

(m3/min)

EPB: RadialSeal

ERB2: RadialSeal

EPB-ERB2 with Full-View Pre-Cleaner: RadialSeal

EPB-ERB2 with Donaspin™ Pre-Cleaner: RadialSeal

ECB DuraLite: Disposable

ECD DuraLite: Disposable

ECC DuraLite: Disposable

Disposables RadialSeal PowerCore® AxialSeal

Hea

vy D

ust C

ondi

tion

M

ediu

m D

ust

L

ight

Dus

t

EPB: RadialSealaB e lP i

ERB2: RadialSealR R d

ECB DuraLite: DisposablerB o l

ECD DuraLite: DisposableesL t sD

ECC DuraLite: DisposablelE oa tLC D

Ligh

t Dus

t

Seala™ Pre-Cleaner: RadialS-EPB-ERB2 with Strata™EPE ™Sh tE B a Se

FLB: Axial SealSF B

SPB2-SRB: RadialSealaRP e

SSG: RadialSealeR d

STG: Axial SealT i S

PSD: PowerCore®P ®C

EPB-ERB2 with Donaspin™ Pre-Cleaner: RadialSealeE Cn is PB t D l

Hea

vy D

ust C

ondi

tion

alSeale™ Pre-Cleaner: RadiaePB-ERB2 with TopSpin™RBE ™t ThE B w R a

alSealeFRG2: RadiaR aR

G + FPG Alexin: RadialSealP+FP Sx n dG l

SealeFTG: Axial G

PSD: PowerCore®PP ®C

FKB: RadialSeal

XRB: RadialSeal

EPB-ERB2 with Full-View Pre-Cleaner: RadialSeal- aRB wu VP 2 w a S

M

ediu

m D

ust

Temperature°C = (°F – 32) x 5/9

°F = (°C x 9/5) + 32

PowerHP = KW x 1,341 (metric)

KW = HP x 0,745 (metric)

Flow rates1 l/min. = 0,0353 cfm

1 m³/min. = 35,3147 cfm

1m³/h = 0,5886 cfm

1 English gallon/min. = 0,1605 cfm

Length1 m = 1000 mm = 39,37 inch = 3,281 ft.

1 inch = 25,4 mm = 0,0254 m = 0,08333 ft.

1 ft. = 304,8 mm = 0,3048 m = 12 inch

Volume1 m³ = 1000 litres = 35,31 ft.³ = 61024 inch³

1 ft.³ = 28,32 litres = 0,02832 m³ = 1728 inch³

1 litre = 0,2642 US gallon = 0,2201 Engl gallon

1 US gallon = 3,785 litres = 231 inch³

1 English gallon = 4,546 litres = 277 inch³

Conversion FactorsAir Filtration

Weight1 kg = 2,205 lb = 35,27 Oz

1 lb = 0,4536 kg = 16 Oz

1 Oz = 0,02835 kg = 0,0625 lb

Pressure1 mm H2O = 9,80665 Pa1 bar = 100 kPa = 14,5 psi

10 mbar = 1 kPa = 0,145 psi

10 psi = 68,95 kPa = 0,6895 bar

1 “Hg = 345,4 mm H2O = 3,321 kPa

Air WeightAir weight at 0°C = 1,293 kg/m³

Air weight at 20°C = 1,205 kg/m³

Air weight at 25°C = 1,184 kg/m³

Engine Air Cleaners, Accessories & Service Parts 17

PowerCore filters in round, obround, and rectangular configurations.

Innovative vehicle designs call for new engineering solutions plus know-how from your suppliers.

We have both – and are ready to help you solve your space or configuration problems.

Engine ProtectionAll Conditionsin

Like Never Before!

PowerCore®

Engine Air Cleaners, Accessories & Service Parts 19

PowerCore® DeliversImproved Filtration

Performance

NEW

Section Index

PSD (Medium to Heavy Dust) . . . . . . . . . . . . . . . 19PSD Service Instructions . . . . . . . . . . . . . . . . . . 34

Engine Air Cleaners, Accessories & Service Parts 19

Pow

erCo

re®

20 Engine Air Cleaners, Accessories & Service Parts

Clean air travels on to your engine

Dirty air travels in and is filtered in one pass through the media

Filter media is formed into flutes - these flutes are layered to give tight, rugged structure to the filter

Fluted channels are alternately sealed: air enters an open flute and is forced to exit through an adjacent flute

Contaminants stay inside the filter - and won’t drop back into an unprotected air filter housing.

PowerCore®Filtration Technology

Why was it developed?

Vehicle design is moving from classic to aerodynamic. This means less under-hood space, highly stylized, cost effective designs, greater operator visibility, higher horsepower engines with greater airflow and other emission requirements with hotter engines…

Therefore Donaldson developed PowerCore® Filtration Technology, to do more in less space and to allow system optimization.

What is it about?

• Proprietary air filtration technology developed to improve engine protection.• Revolutionary, fluted media design for improved air filtration.• PowerCore® media is visually unique.• PowerCore filters can be designed, based on an approved matrix, in obround (racetrack) and round shapes.• High density media packaging technology.• Several features patented and IP protected.• Backed by extensive lab and field testing

How does it work?

y

amic. This means less under-hood spacehigher horsepower engines with greater

PowerCore®Filtration Technology

With PowerCore, you will gain…

Greater EfficiencyThe straight-through fluted design of PowerCore Filtration Technology is three times more efficient than average conventional pleated filters.

Engine ProtectionNo media movement, expansion, contraction or bunching, with less dust and dirt passed on to the engine.

Contaminant EncapsulationDust and dirt won’t dislodge during servicing.

Equal or Better Performance in a Small PackageThe freedom to design unique configurations to fit tight spots and overall design simplicity.

Donaldson ReliabilityBacked by nearly a century of innovation and experi-ence. Donaldson supplies air filtration products to almost every vehicle manufacturer.

Lower Shipping and Inventory CostsPowerCore filters are lighter and take up less shelf space being so compact - in fact as much as half of a conventional filter.

Improved Handling and MaintenanceLighter and smaller, changing filters is a snap.

Improved Environment ProtectionNon-metal filters – both main and safety (where applicable).

System Design FlexibilityMultiple horizontal and vertical installation positions.

Dust Holding CapacityGain over 100% more dust holding capacity in a given volume.

Built-In Pre-Separation and Mounting BracketsTo eliminate the need to purchase separate.

Filtration T

n…

CoreLower Shipping and InventoP C fil li h

Millions of units have been installed worldwide in on- and off-road applications.

PowerCore®

Engine Air Cleaners, Accessories & Service Parts 21

Pow

erCo

re®

22 Engine Air Cleaners, Accessories & Service Parts

Excellent Performance in Half the Space

The PSD PowerCore® Air Cleaner is a two-stageair cleaner with built-in high efficiency pre-cleanerusing PowerCore Filtration Technology.

PSD PowerCore Air Cleaners are designedespecially for on and off road equipment operating in medium to heavy dust environments. Can be used with Vacuator™ Valve on the pre-cleaner or continuously scavenge of the pre-cleaner by an exhaust ejector or air blower cooling. See page 124-125 for all available Exhaust Ejectors.

• Equipment operating in medium to heavy dust conditions with engine airflow ranges up to 30 m³/min.• Obround housing shape allows for a narrow or wide mounting orientation. Models have either end or side filter service access• Sustained temperature tolerance: to 82°C

Applications

• More compact at a given performance level than standard pleated filters• Non-metal filters - both main and safety (where applicable)• Improved engine protection: no media movement, expansion, contraction or bunching• Improved contaminant encapsulation: dust and dirt stay contained in filter during service• Improved filtration efficiency: - Three times more efficient than the average conventional pleated filter - PowerCore Filtration Technology with high efficiency pre-cleaner tubes improve engine protection• Improved handling and maintenance: lighter and smaller, changing filters is a snap• Easily serviced with clamp-on cover design• Can be used with scavenge line or Vacuator™ Valve depending on housing orientation• Built in mounting brackets eliminate the need to purchase separate mounting bands• Indicator thread size = 1/8-27NPT (Male) for PSD08/PSD09/PSD10 1/8-27NPT (Female) for PSD12

Features Mounting FlexibiltyThe PSD air cleaner is available with two separatedrop tube in orientations and built- in mounting brack-ets on the 2 long sides of the housing. The ohter three PSD models (09, 10 and 12) offer even more mounting flexibility with built- in brackets on three sides of the main body housing.

D080069 - Horizontal D080070 - Vertical

D090074 - Horizontal D090073 - Vertical

D100030 - Horizontal D100029 - Vertical

PSD Air Cleaner

PSD Air CleanerPow

erCore®

Engine Air Cleaners, Accessories & Service Parts 23

PSD 08 - Service Access on Inlet End

PSD 09-10-12- Service Access on Side

Straight

Indicator

90°

A

B

C

D

EF

GH

PSD Air Cleaner Po

wer

Core

®

24 Engine Air Cleaners, Accessories & Service Parts

PSD 08 - Specifications

PSD air cleaners are designed to operate with or without aspiration, otherwise known as scavenging. Scavenging is accomplished by introducing a secondary airflow to the drop tube on the air cleaner (generally through the use of an ejector or ejector muffler). This flow pulls the separated contaminant from the precleaner and inserts it into the exhaust stream.

The advantages to scavenging are:• Higher pre-cleaner efficiency (resulting in longer filter service life)• Completely self-servicing (no regular maintenance needed on pre-cleaner)• Drop tube can be located in variety of orientations (not just straight down as is necessary on non-scavenged systems)

Aspirating an intake system through the use of a scavenging device adds more components (an ejector and some plumb-ing) to the overall system, but will enhance the separator efficiency of the pre- cleaner and consequently extend the filter service life. Conversely, the PSD air cleaner and precleaner will function adequately without scavenge, with the result being less filter service life than with the use of scavenging.

To Scavenge or Not Scavenge…

NEW

NEW

Air Cleaner Airflow Range Dimensions (mm) Model No. m³/min. A B C D E F G H

D080069 (H) D080070 (V) up to 6 With Vac Valve 89 380 257 159 100 117 191 76 D080069 (H) D080070 (V) up to 8,5 With Scavenge Flow (H) Horizontal / (V) Vertical Installation

PSD Air CleanerPow

erCore®

Engine Air Cleaners, Accessories & Service Parts 25

(H) Horizontal / (V) Vertical Installation * 90° Outlet

PSD 09 - 10 - 12 Specifications

PSD09

PSD10

PSD12

K

433433458458533533477477502502577577429429529529505505605605496496596596

362362362362362362362362362362362362375375375375375375375375430430442442

180180180180180180180180180180180180254254254254254254254254306306306306

110110135135180180110110135135180180110110210210110110210210168168268268

174174174174174174218218218218218218165165165165241241241241160160160160

100100100100100100100100100100100100110110110110110110110110154154154154

130130130130130130130130130130130130110110110110110110110110110110110110

76,576,576,576,576,576,576,576,576,576,576,576,576,576,576,576,576,576,576,576,576767676

NEW

NEW

NEW

NEW

NEW

NEW

NEW

NEW

Air Cleaner Airflow Range Dimensions (mm) Model No. m³/min. A B C D E F G H K With 10% Scavenge Flow

D090073 (V) 6-10 102 D090074 (H) 6-10 102 D090099 (V) 7-11 102 D090098 (H) 7-11 102 D090101 (V) 9-13 102 D090100 (H) 9-13 102 D090086 (V)* 6-10 102 D090087 (H)* 6-10 102 D090088 (V)* 7-11 102 D090089 (H)* 7-11 102 D090090 (V)* 9-13 102 D090091 (H)* 9-13 102 D100029 (V) 12-18 127 D100030 (H) 12-18 127 D100031 (V) 18-25 152 D100032 (H) 18-25 152 D100124 (V)* 12-18 127 D100123 (H)* 12-18 127 D100122 (V)* 18-25 127 D100121 (H)* 18-25 127 D120035 (V) 23-27 152 D120036 (H) 23-27 152 D120037 (V) 27-30 152 D120038 (H) 27-30 152

Service Parts

PSD Air Cleaner Po

wer

Core

®

26 Engine Air Cleaners, Accessories & Service Parts

PSD PowerCore® - Service Parts

Air Cleaner Model No.

Air Cleaner Installation Version Orientation

Drop TubeOrientation

OutletAccess Cover

AssyU-Clip,

Mounting (x4)Main

ElementSafety

Element

D080069 Horizontal - Horizontal Straight P785236 P786050 P608533 P600975

D080070 Vertical - Vertical Straight P785237 P786050 P608533 P600975

D090073 Vertical Short Vertical Straight P785651 P784517 P608665 P606121D090074 Horizontal Short Horizontal Straight P785651 P784517 P608665 P606121D090099 Vertical Medium Vertical Straight P785978 P784517 P787281 P606121D090098 Horizontal Medium Horizontal Straight P785978 P784517 P787281 P606121D090101 Vertical Long Vertical Straight P786989 P784517 P608675 P606121D090100 Horizontal Long Horizontal Straight P786989 P784517 P608675 P606121

D090086 Vertical Short Vertical 90° P785651 P784517 P608665 P606121D090087 Horizontal Short Horizontal 90° P785651 P784517 P608665 P606121D090088 Vertical Medium Vertical 90° P785978 P784517 P787281 P606121D090089 Horizontal Medium Horizontal 90° P785978 P784517 P787281 P606121D090090 Vertical Long Vertical 90° P786989 P784517 P608675 P606121D090091 Horizontal Long Horizontal 90° P786989 P784517 P608675 P606121

D100029 Vertical Short Vertical Straight P784517Upon request P601560D100030 Horizontal Short Horizontal Straight P784517Upon request P601560D100031 Vertical Long Vertical Straight P784517Upon request P601560D100032 Horizontal Long Horizontal Straight P784517Upon request P601560

D100124 Vertical Short Vertical 90° P784517Upon request P601560D100123 Horizontal Short Horizontal 90° P784517Upon request P601560D100122 Vertical Long Vertical 90° P784517Upon request P601560D100121 Horizontal Long Horizontal 90° P784517Upon request P601560

D120035 Vertical Short Vertical Straight P784517Upon request P607557D120036 Horizontal Short Horizontal Straight P784517Upon request P607557D120037 Vertical Long Vertical Straight P784517 P608677 P607557D120038 Horizontal Long Horizontal Straight P784517 P608677

P608666P608666P608676P608676

P608666P608666P608676P608676

P608667P608667P608677P608677

Upon requestUpon request P607557

Service Parts

Version

Vacuator™ Valve P112803 for the European PSD Range / P158914 for the US PSD Range - See page 27. When making use of a reducer, see page 141 for all available Vac Valves

Check Valve P784790 for the PSD Range. See page 126 for all available Check Valves.Adapters ø 32 = P783747 ø 38 = P783746 ø 50 = P783748

ø 25 + 90° = P786685 ø 32 + 90° =P784019 (PP) ø 32 + 90° =P784834 (PA) ø 38 + 90° = P786778

Accessories used on all PSD Air Cleaners

Ejectors See page 124-125 for all available Exhaust Ejectors

Media used on PSD PowerCore® Standard Air Cleaners

All PSD Standard Air Cleaners are equiped with White Media, Blue Ultra-Web® Media is optional. Contact your Donaldson representative for more info.

Adapter 90°

Adapter Straight

PSD Air CleanerPow

erCore®

Engine Air Cleaners, Accessories & Service Parts 27

PSD08 Extended Product Line - Features

• Lower initial restriction• Mounting brackets on both sides to increase mounting options• Drop tube diameter enlarged (same as PSD10 & 12)• Possibility to fix different scavenge adapters > straight & 90°• Possibility to integrate check-valve into scavenge tube of pre-cleaner• 4 latches on service cover to improve accessibility & serviceability

PSD09 Extended Product Line - Features

• Lower initial restriction• Next to the short and long PSD09 we offer now a medium version• Drop tube diameter enlarged (same as PSD10 & 12)• Possibility to fix different scavenge adapters > straight & 90°• Possibility to integrate check-valve into scavenge tube of pre-cleaner• Optional 45° latch position on the cover• New version with 90° outlet tube • Male indicator tab with thread 1/8 27 NPT

PSD10 Extended Product Line - New features

• New version with 90° outlet tube

PSD Extended Product Line now available!

For the PowerCore™ Air Cleaner Range, Donalson now offers you more alternatives - an extended product line. These new alternatives provide you more flexibility and mounting options. A new range of accessories is also available (see page 26).

Standard PSD PowerCore® Line European Models D080020 D080069 New D080026 D080070 New

PSD09 D090019 D090073 New D090020 D090074 New - D090099 New - D090098 New D090021 D090101 New D090022 D090100 New - D090086 New - D090087 New - D090088 New - D090089 New - D090090 New - D090091 New

- D100029 Existing - D100030 Existing - D100031 Existing - D100032 Existing - D100124 New - D100123 New - D100122 New - D100121 New

D120035 - Existing D120036 - Existing D120037 - Existing D120038 - Existing

PSD08

PSD09

PSD10

US Models

PSD12

ou more alternatives - an exunting options A new rang

NEW

PSD Service InstructionsPo

wer

Core

®

34 Engine Air Cleaners, Accessories & Service Parts

1 Shut off engine. Unlatch and remove the housing service cover.

2 Remove primary filter. Pull the filter out of housing. On PSD09, PSD10, and PSD12 you

must first loosen the filter gasket seal. Using the handle, push down on the filter to loosen the seal, which will tilt the filter to approximately a 5º angle.

3 Remove safety filter. Using the plastic handle on the face of the safety filter, pull the

filter toward the center of the housing and remove. Note: A safety filter only needs to be replaced at every third primary air filter change.

4 Inspect the new filter before installing. Visually check for cuts, tears, or indentations

on the sealing surfaces before installation. If any damage is visible, do not install.

Plastic Handle

Plastic Handle

PSD09, PSD10 or PSD12 Style PSD08 Style

Note: Your air cleaner service cover may bein a different position than shown.

PSD Service InstructionsPow

erCore®

Engine Air Cleaners, Accessories & Service Parts 35

5 If replacing safety, using the plastic handle on the safety filter, slide the filter at an angle into the

outlet side and push in place until the filter seats firmly and evenly within the housing. Note: On PSD09, PSD10 and PSD12 models, insert the safety filter tab into the positioning slot before pushing the filter in place.

6 Insert the primary filter. For PSD08, slide the filter into the housing until the gasket seats

against the housing. For PSD09, PSD10 and PSD12, slide the filter down at approximately a 5º angle until it hits the end of the housing. Rotate the filter toward the outlet section to complete the seal.

7 Replace the service cover. On PSD08, tilt the service cover into place and secure latches.

For the PSD09, PSD10 and PSD12, placed the service cover in position and fasten the latches. Note: If the cover doesn’t seat, remove and re-check the filter position. The cover will be difficult to install if the filter isn’t installed correctly.

8 Visually inspect your inlet and outlet connections. If your air cleaner has a Vacuator

Valve, inspect the valve. Replace if any signs of wear or damage are visible.

Safety Filter Positioning Tab Location

PSD09, PSD10 or PSD12 Style PSD08 Style

Plastic Handle

PowerCore filters in round, obround, and rectangular configurations.

Innovative vehicle designs call for new engineering solutions plus know-how from your suppliers.

We have both – and are ready to help you solve your space or configuration problems.

Engine ProtectionAll Conditionsin

Like Never Before!

Light Dust Conditions

Engine Air Cleaners, Accessories & Service Parts 37

Light Dust ConditionsAir Cleaners used in

... Donaldson offers a full line of air cleaners for a wide variety of applications and operating environments.

UNIQUE DESIGN CONCEPT

UNDE

CCCCCCON NEW

Section Index

DuraLite™ ECB, ECC, ECD. . . . . . . . . . . . . . . . . . 38DuraLite Service Instructions. . . . . . . . . . . . . . . 42EPB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43EPB Service Instructions. . . . . . . . . . . . . . . . . . . 48ERB2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43ERB2 Service Instructions. . . . . . . . . . . . . . . . . . 48PT

DuraLite™ ECB, ECC, ECDAir Cleaner

The DuraLite™ Air Cleaners are dis-posable, one-stage, dry air cleaners which are used on light-duty appli-cations like air compressors, pumps, material handling equip-ment, propulsion units, breathers, welders, generator sets, lawn vehi-cles, recreation vehicles and many more. Ideal for high pulsating small engines.

Donaldson's DuraLite™ air cleaners are tough, non-metallic, lightweight, self-supporting and completely dis-posable. They are also easy to install, durable, and reliable.

They are designed to function well under high and severe pulsation conditions found in many applica-tions, especially two- and three-cyl-inder engines. Vibration-resistant media is potted into molded hous-ings of rugged ABS plastic - so they don’t fall apart as other designs might.

Applications• Can be mounted vertically or horizontally.• Provides variety of airflow volumes to engine: from 1 to 90 m³/min.• Temperature tolerance: to 83°C continuous / 105°C intermittent.

Convenient DuraLite Disposables Rugged Air Cleaners for Small and/or High Pulsation Gas & Diesel Engines

Ligh

t Dus

t Con

ditio

ns

ECB StyleECC Style

ECD Style

Air Cleaner Features• No serviceable parts! Air cleaner housing and filter are one unit!• Designed to withstand severe intake pulsation.• Economical replacement cost.• Self-supporting, sturdy.• Very reliable: only one critical seal.• Lightweight and compact in size.• Non-metallic, non-corrosive... ideal for marine applications.

• Completely disposable... acceptable for normal trash pick-up (DuraLite™ should not be incinerated).• Easily installed & maintained.• Minimal removal clearance needed: only 38 mm.• Three airflow styles available to fit virtually any engine intake configuration.• Various media available for specific applications: high pulsation, high humidity, etc....

Donaldson recommends the use of a high torque clamp for DuraLite air cleaners. This clamp eliminates the need for

double clamping - order one for each DuraLite™ Air Cleaner. See page ... for more information.

38 Engine Air Cleaners, Accessories & Service Parts

DuraLite™ ECB, ECC, ECDAir Cleaner

Light Dust Conditions

DuraLite™ Specifications

Curve No. Style Air Cleaner Airflow Range Dimensions Model No. m³/min. (mm) A B D 1 ECB B085001 6 - 12 216 279 76 1 ECB B085048** 6 - 12 216 279 76 2 ECB B085011 7 - 14 216 279 102 2 ECB B085046** 7 - 14 216 279 102 3 ECB B085056** 27 - 49 196 260 152 4 ECB B100094** 15 - 27 267 228 102 5 ECB B105002* 16 - 30 267 381 127 6 ECB B105006 13 - 25 267 267 102 7 ECB B105012** 18 - 36 267 381 127 8 ECB B120376** 30 - 90 318 400 198 9 ECB B125003* 16 - 31 318 381 153 10 ECB B125005** 25 - 42 318 229 140 11 ECB B125011** 22 - 39 318 228 127

Curve No. Style Air Cleaner Airflow Range Dimensions Model No. m³/min. (mm) A B D 12 ECC C045001* 1 - 3 114 114 38 13 ECC C045002* 2 - 3 114 203 38 14 ECC C055002* 2 - 4 140 178 45 15 ECC C055003* 1,5 - 3 140 102 45 16 ECC C055008* 2 - 4 140 242 45 17 ECC C065001* 2 - 3 165 102 51 18 ECC C065002* 3 - 5 165 190 51 19 ECC C065003* 2,5 - 5 165 127 57 20 ECC C065004* 3 - 6 165 229 57 21 ECC C065015** 3 - 6 165 229 51 22 ECC C085001* 3 - 5 216 102 64 23 ECC C085002* 3 - 6 216 165 64 24 ECC C085003* 4 - 7 216 127 76 25 ECC C085004* 5 - 10 216 241 76 26 ECC C085005* 3 - 5 216 127 64 27 ECC C085006* 3,5 - 6,5 216 241 64 28 ECC C105003 9 - 17 267 152 102 29 ECC C105004 10,5 - 20 267 267 102 30 ECC C125003 10 - 19 317 152 127 31 ECC C125004 14 - 26,5 317 279 127

Curve No. Style Air Cleaner Airflow Range Dimensions Model No. m³/min. (mm) A B D 32 ECD D045003* 1 - 3 114 114 38 33 ECD D045004* 1 - 3 114 152 38 34 ECD D055004* 2 - 3,5 140 178 45 35 ECD D065003* 2 - 3 165 102 51 36 ECD D065008** 3,5 - 7 165 229 51 37 ECD D085011 8 - 15,5 197 655 106 38 ECD D085012 2,5 - 7,5 197 258 106 39 ECD D125004 12 - 23 317 279 127

* High pulsation media ** Marine application

Engine Air Cleaners, Accessories & Service Parts 39

DuraLite™ ECB, ECC, ECDService Instructions

Service Recommendations

Servicing IntervalsChoose either of two types:• Scheduled maintenance. DuraLite service intervals can be integrated into any existing maintenance program.• Restriction Maintenance. This method offers the most accurate filter maintenance program, delivering maximum filter life at 99.9% efficiency, less machine downtime, and reduced maintenance costs.• Washing, cleaning or servicing the filter in any way voids the warranty.

Service Indicator LocationFor proper restriction readings, a restriction fitting tap must be located between the engine intake and DuraLite outlet neck. The tap should be located in a straight section of the intake pipe at least one pipe diameter away from the manifold or any bends, elbows or reducers.

Servicing Tips• Do NOT judge the filter on the basis of visual inspection! If it's doing its job, it should look dirty. DuraLite filter life is longer than you may think. Change the filter only when restriction readings indicate.• Do NOT leave the inlet ducting exposed any longer than necessary (a few minutes) during service.

DisposalNormal trash pick up is acceptable - never burn.

Installation Instructions

InstallationDuraLite air cleaners can be mounted in two ways:1. Direct Mount: mounted directly on the intake manifold.2. Remote Mount: mounted away from engine and connected to engine with inlet piping.

Installation Tips• Engage outlet neck of the DuraLite™ over intake piping for a full 38 mm to insure a secure, lasting seal.• Tighten clamp around outlet neck to 0.7 daNm minimum. A Donaldson high torque hose clamp is recommended.• On remote mount style, avoid crushing the body with body clamps. A snug fit is best, and body clamps are not always required.• Keep away from engine manifold and other very hot components (DuraLite™ is rated at 83°C maximum sustained temperature).• Keep away from battery acids, brake fluid, and other caustic fluids.

Torque clamp to 0.7 daNm (minimum)

Torque clamp to 0.7 daNm (miminum)38 mm

38 mm

Ligh

t Dus

t Con

ditio

ns

42 Engine Air Cleaners, Accessories & Service Parts

EPB – ERB2 Air Cleaner Light Dust Conditions

Engine Air Cleaners, Accessories & Service Parts 43

UNIQUE DESIGN CONCEPT

QUUEEEEEEE GN EPT

NEW

Primary Dry RadialSeal™ Air Cleaners which offer improved reliability and durability, reduced weight and costs and better serviceability.

The EPB-ERB2 Primary Dry RadialSeal™ Air Cleaners are used on light-duty applications like on-highway vehicles, stand-by generator sets and all other light-duty applications. They are also used on medium- and heavy-duty applications but than always combined with a Pre-Cleaner.

For more details on EPB-ERB2 Air Cleaners with Pre-Cleaners operating in Medium Dust conditions see page 60-63 and in Heavy Dust conditions see page 93-96 .

The EPB Air Cleaner is a one-stage full-plastic air cleaner

The ERB2 Air Cleaner is a one-stage hybrid air cleaner.It is the Next Generation ERB Air Cleaner Product

featuring Donaldson's Unique Design Concept.For more details on this UDC Feature, see page 7.

Applications EPB-ERB2• Can be mounted vertically or horizontally• Provides variety of airflow volumes to engine: from 2 to 65 m³/min.• Temperature tolerance: to 83°C continuous / 105°C intermittent.

Features EPB-ERB2• Cost effective / Compact and light• Flexible installation / Conquers underhood space limitations• Reliable, durable, high-tech and easy to service design• Proven RadialSeal™ Technology• Pre-cleaner can be added / Tapped for restriction indicator as standard

Filter inside air cleaner is different from filters with metal end caps• One-piece molded end caps encase the ends of media and filter liners • Filter fits over the housing outlet tube, creating a reliable seal - with no hassle of separate sealing gaskets • Indicator thread size = 1/8-27NPT (MALE)•

Patent Pending for Donaldson's Unique Design Concept.

Ligh

t Dus

t Con

ditio

ns

EPB – ERB2 Air Cleaner

EPB Specifications - Service Parts

44 Engine Air Cleaners, Accessories & Service Parts

Air Cleaner Airflow Range Dimensions (mm) Model No. m³/min. A B C D E F H J X° Z°°

B070005* 2 - 5 182 334 76 76 45 27 115 145 340 45 B080067* 4 - 7 210 355 95 89 54 31,5 130 146 355 110 * Includes safety element X° Free space needed to remove main element Z°° Free space needed to remove cover

Air Cleaner Main Safety Access Mounting Model No. Element Element Cover Assy* Raincap band**

B070005 P772579 P775300 P778758 H001379 P777731B080067 P772580 P775302 P775305 H770010 P777732

* Spare Part only ** Only one mounting band needed per Air Cleaner

Service Parts

ERB2 ERBAir Cleaners

B100126 B100120 B130057 B130010 B130058 B130013 B150058 B150025 B150059 B150028 B180016 B180011 B180017 B180012

ERB2 Main Kit Number • Access Raincap Mounting Air Cleaner Element Cover Assy* band**

B100126 P785388 X770685 P784954 H770012 P004076 B130057 P785610 - P783693 H770089 P013722 B130058 P785610 X770686 P783693 H770089 P013722 B150058 P785426 X770687 P784869 H770089 P016845 B150059 P785426 - P784869 H770089 P016845 B180016 P785394 - P785546 H770082 H770037 B180017 P785394 X770688 P785546 H770082 H770037

* Spare Part only ** Two mounting bands needed per Air Cleaner • Safety element can only be bought as a kit meaning together with the main element

Air Cleaner Airflow Range Dimensions (mm) Model No. m³/min. A B C D E F H J X° Z°°

B100126* 8 - 14 259 430 114 102 143 52 205 0 400 75 B130057 18 - 30 330 530 178 152 180 58 215 0 360 95 B130058* 18 - 28 330 530 178 152 180 58 215 0 360 95 B150058* 18 - 32 381 590 178 178 136 70 241 102 540 93 B150059 18 - 32 381 590 178 178 136 70 241 102 540 93 B180016 32 - 65 457 650 254 203 282 85 328 0 600 130 B180017* 32 - 65 457 650 254 203 282 85 328 0 600 130 * Includes safety element X° Free space needed to remove main element Z°° Free space needed to remove cover

Service Parts

ERB2 Specifications - Service Parts UNIQUE DESIGN CONCEPT

UNDE

CCCCOC N NEW

Light Dust Conditions

EPB – ERB2 Air Cleaner

Replaces

Engine Air Cleaners, Accessories & Service Parts 45

48 Engine Air Cleaners, Accessories & Service Parts

Ligh

t Dus

t Con

ditio

ns

EPB-ERB2 Service Instructions

4 Inspect the New Filter for DamageInspect the new filter carefully, paying attention to the inside of the open end, which is the sealing area. NEVER install a damaged filter. A new Donaldson radial seal filter may have a dry lubricant on the seal to aid installation.

5 Insert the New Radial Seal Filter ProperlyIf you’re servicing the safety filter, this should be seated into position before installing the primary filter.

Insert the new filter carefully. Seat the filter by hand, making certain it is completely into the air cleaner housing before securing the cover in place.

The critical sealing area will stretch slightly, adjust itself and distribute the sealing pressure evenly. To complete a tight seal, apply pressure by hand at the outer rim of the filter, not the flexible center. Avoid pushing on the center of the urethane end cap. No cover pressure is required to hold the seal. NEVER use the service cover to push the filter into place! Using the cover to push the filter in could cause damage to the housing, cover fasteners and will void the warranty.

If the service cover hits the filter before it is fully in place, remove the cover and push the filter (by hand) further into the air cleaner and try again. The cover should go on with no extra force.

Once the filter is in place, secure the service cover.

6 Check Connectors for Tight FitMake sure that all mounting bands, clamps, bolts, and connections in the entire air cleaner system are tight. Check for holes in piping and repair if needed. Any leaks in your intake piping will send dust directly to the engine!

1 Remove the Filter Unfasten or unlatch the service cover.

Because the filter fits tightly over the outlet tube to create the critical seal, there will be some initial resistance, similar to breaking the seal on a jar. Gently move the end of the filter back and forth to break the seal then rotate while pulling straight out. Avoid knocking the filter against the housing.

If your air cleaner has a safety filter, replace it every third primary filer change. Remove the safety filter as you would the primary filter. Make sure you cover the air cleaner outlet tube to avoid any unfiltered contaminant dropping into the engine.

Clean Both Surfaces of the Outlet Tube 2 and Check the Vacuator™ Valve Use a clean cloth to wipe the filter sealing surface and the inside of the outlet tube. Contaminant on the sealing surface could hinder an effective seal and cause leakage. Make sure that all contaminant is removed before the new filter is inserted. Dirt accidently transferred to the inside of the outlet tube will reach the engine and cause wear. Engine manufacturers say that it takes only a few grams of dirt to “dust” an engine! Be careful not to damage the sealing area on the tube.

If your air cleaner is equipped with a Vacuator Valve Visually check and physically squeeze to make sure the valve is flexible and not inverted, damaged or plugged.

Inspect the Old3 Filter for Leak CluesVisually inspect the old filter for any signs of leaks. A streak of dust on the clean side of the filter is a telltale sign. Remove any cause of leaks before installing new filter.

Wipe both sides of the outlet tube

clean.

Outer edge of the outlet tube

Inner edge of the outlet tube

NEVER use the service cover to push the filter into place! Using the cover to push the filter in could cause damage to the housing, cover fasteners and will void the warranty.

Caution

Rotate the filter while pulling straight out.

Air Cleaners used inM

edium Dust Conditions

Medium Dust Conditions... Donaldson offers a full line of air cleaners for a wide variety of applications and operating environments.

Engine Air Cleaners, Accessories & Service Parts 49

UNIQUE DESIGN CONCEPTDES

CCCCCCOC N NEW NCEPTCCCCCCCONW

UNIQUE DESIGN CONCEPT

UNDES

CCCCCCOC N NEW NCEPTCCCCCCCONW

NEW

NIQUE SIGN

UNDES

NEW

Section Index

FKB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50FKB Service Instructions. . . . . . . . . . . . . . . . . . . 54XRB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55XRB Service Instructions . . . . . . . . . . . . . . . . . . 59EPB-ERB2 with Full-View Pre-Cleaner . . . . . . . 60EPB-ERB2 with TopSpin™ Pre-Cleaner . . . . . . 62FPG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64FPG Alexin™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70FPG + FPG Alexin Service Instructions. . . . . . . 76FPG + FPG Alexin Mounting Bands . . . . . . . . . . 77 FTG Cycloflow™ . . . . . . . . . . . . . . . . . . . . . . . . . . 78FTG Service Instructions . . . . . . . . . . . . . . . . . . . 81FRG2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82FRG2 Service Instructions. . . . . . . . . . . . . . . . . . 88

50 Engine Air Cleaners, Accessories & Service Parts

FKB Air CleanerM

ediu

m D

ust C

ondi

tions

Smaller, Lightweight Alternative Two-Stage Air CleanerDesigned for horizontal installation

The FKB series is a family of two-stage air cleaners for medium dust conditions.

Compared to other air cleaner styles, this new air cleaner family delivers the performance of competitive larger air cleaners in a compact, rugged design.

With heavy-duty plastic construction and non-metal filters, the air cleaner is lighter, more efficient and easier to install and replace than competing products.

Another key design feature is the built-in mounting brackets. There's no need for additional mounting support.

The two stage design features a built-in pre-cleaner that separates up to 85% of airborne contaminants.

ngine Air Cleaners, Accessories & Service Parts

The FKB's plastic housing and durable construction enables installation in all types of medium-dust environments with engine air flow from 2 - 10 m³/min.

FKB air cleaners effectively reduce contaminants flowing into the air intake system, provide a

FKB05

FKB04

FKB06

high level of engine protection from harmful contaminants and increase engine performance and fuel efficiency.

The air cleaner models ship with both the main and safety filters.

NEW

Donaldson FKB air cleaners are protected internationally by patents, trademarks, and design registrations, both issued and pending.

Engine Air Cleaners, Accessories & Service Parts 51

FKB Air CleanerM

edium Dust Conditions

Built-in Mounting Brackets and Filter Indicator Port Easy to service with non-metal filters

Applications

• Off-road equipment operating in medium-dust conditions with engine airflow range of 2 to 10 m³/min.

• Installs horizontally. Mounting the air cleaner directly to the engine is not recommended; excessive engine vibration can cause premature air cleaner structural failure

• Sustained temperature tolerance:to 82°C. Do not install next to components that exceed the maximum temperature (82°C); like a turbocharger, muffler, exhaust pipe or other high temperature component

Inlet

Filter changeout is a snap with minimal service clearance required

Outlet

Unique Twist & Lock Filter ensure proper positioning during filter service. Air cleaners assemblies include main and safety filters.

Air Cleaner Features

• Smaller in diameter compared to competitive brands with similar airflow

• Improved handling and maintenance: lighter and smaller, changing filters is a snap

• Product design includes: - main filter - safety filter - filter service indicator port

• Improved filter disposal ease: no metal

• Cover latch position allows for minimum service clearance and eases filter service

• Mounting brackets built-in to air cleaner body eliminating need for mounting bands

• Indicator thread size = 1/8-27NPT (MALE)

Service Parts

52 Engine Air Cleaners, Accessories & Service Parts

FKB Air CleanerM

ediu

m D

ust C

ondi

tions

E

AK

C

I

B

H

(2 - B04,B05 and B06)

D

F

G

J

Cover End View for B04, B05, and B06

M8 X 1.25

Side View

Air Cleaner Main Safety Access Vacuator™ Model No. Element Element Cover Assy Valve

B045008 P604457 P603729 P606497 P158914 B055006 P609218 P602427 P609219 P158914 B065045 P609221 P608599 P608592 P158914

Air Cleaner Airflow Range Dimensions (mm) Model No. m³/min. A B C D E F G H I J K

B045008 2 - 3 133 51 51 342 99 72 41 157 189 52 72B055006 3 - 4 152 64 64 404 99 73 49 157 244 52 77B065045 4 - 6 180 76 76 408 120 73 53 188 241 52 90

FKB Specifications - Service Parts NEW

• Shut off your engine.

• Air cleaner orientation is horizontal, with the drop tube pointing down - within +/- 15°. For service clearance, allow the entire length of the filter for removal and 35mm for service cover latches.

• Mounting is M8 x 1,25 with a maximum torque of 20,34 Nm.

• Connections: Inlet/Outlet maximum torque 4,52 Nm Indicator port maximum torque 2 Nm.

• Inlet accessory note: The air cleaner housing can accommodate a lightweight inlet hood, but not a pre-cleaner or any other accessory. Use of an unapproved intake accessory will void your Donaldson warranty.

7 Install the new filterInstall new filter by pressing and rotating the filter clockwise until fully engaged to stop.

8 Replace the coverReplace the service cover. The “INLET” arrow should line up with the air cleaner inlet. DO NOT force cover onto air cleaner. The cover should go on with no extra force. If cover is not flush to the body, the filter is not properly seated in the housing.

9 Refasten the latchesRefasten latches to secure cover. Make sure that latches penetrate the slots in both the body and the cover.

10 InspectInspect and torque all clamps, bolts and connections in the entire air intake system. Check for holes in piping, and repair if needed. If Vacuator Valve is damaged replace.

11 Restart the engine

1 Shut off your engine

2 Remove service coverUnlatch and remove the service cover. To remove the primary filter, press and rotate filter counterclockwise until filter is free.

3 Remove the filterGently pull the filter out of housing. Avoid dislodging contaminant from the filter or knocking it against the housing.

4 Clean the inside surfaceWith a soft rag, thoroughly clean the inside surface of the housing. Be careful not to introduce contaminant into the outlet tube.

5 Check the safety filterCheck safety filter for damage. If damaged, replace. Also check to insure that the safety filter is properly seated in the housing. It should fit snugly inside the outlet tube.

6 Inspect the new primary filterInspect the new main filter carefully. Check for any voids, cuts, tears or indentations in the urethane-sealing surfaces.

Installation Recommendations

FKB Service Instructions

54 Engine Air Cleaners, Accessories & Service Parts

Med

ium

Dus

t Con

ditio

ns

Service Instructions

Compact, Radial Seal, Medium-Duty Air Cleaner Designed for horizontal installation

XRB Air Cleaner

Engine Air Cleaners, Accessories & Service Parts 55

Medium

Dust Conditions

Compared to other air cleaner styles, this new air cleaner family is smaller in size compared to competitive models with similar airflow operating ranges.

XRB air cleaners effectively reduce contaminants flowing into the air intake system, provide a high level of engine protection from harmful contaminants and increase engine performance and fuel efficiency.

The XRB's plastic housing and durable construction enables installation in medium-dust environments with engine airflow from 7,5 to 18 m³/min.

The B080080 has non-metal main and safety filters. The main filters for the B100127 and B120420 have metal outer liners. The air cleaner models ship with both the main and safety filters.

Like our FKB and PSD models, these air cleaners feature built-in mounting brackets. There's no need for additional mounting support.

Donaldson XRB air cleaners are protected internationally by patents, trademarks, and design registrations, both issued and pending.

Donaldson XRB air cleaners are protectedinternationally by patents, trademarks, and design registrations, both issued and pending.

NEW

(B080080)XRB08

(B120420)XRB12

XRB10

XRB Air Cleaner

56 Engine Air Cleaners, Accessories & Service Parts

Med

ium

Dus

t Con

ditio

ns

Built-in Mounting Brackets and Filter Indicator PortEasy to service with non-metal filters

Applications

• Off-road equipment operating in medium-dust conditions with engine airflow range of 7,5 to 18 m³/min.

• Installs horizontally. Mounting the air cleaner directly to the engine is not recommended; excessive engine vibration can cause premature air cleaner structural failure

• Sustained temperature tolerance:to 82°C. Do not install next to components that exceed the maximum temperature (82°C); like a turbocharger, muffler, exhaust pipe or other high temperature component

Outlet to Engine

Latched covers makes filter change a snap with minimal service clearance required

Inlet

Filter Service Indicator Port

Built-in Mounting Bracket

Drop Tube with Vacuator Valve

Air Cleaner Features

• Smaller in diameter compared to competitive brands with similar airflow

• Improved handling and maintenance: lighter and smaller, changing filters is a snap

• Product design includes: - main filter - safety filter - filter service indicator port

• Cover latch position allows for minimum service clearance and eases filter service

• Mounting brackets built-in to air cleaner body eliminating need for mounting bands

• Indicator thread size = 1/8-27NPT (MALE)

Service Parts

XRB Air Cleaner

Engine Air Cleaners, Accessories & Service Parts 57

Medium

Dust Conditions

XRB Specifications - Service Parts

K

E

A

Side View

G

B

ID

J

HF

Mounting Bracket

M8 x 1.25” (4 places)

Cover / End View

Air Cleaner Airflow Range Dimensions (mm) Model No. m³/min. A B C D E F G H I J K

B080080 7,5 - 10 231 102 102 425 140 61 80 198 375 40 110B100127 9 - 13,5 287 127 114 565 198 72 88 225 493 50 145B120470 13,5 - 18 330 152 128 601 218 71 100 245 526 50 165

Air Cleaner Main Safety Access Vacuator™ Model No. Element Element Cover Assy Valve

B080080 P611190 • P611189 P605731 P158914 B100127 P611539 * P611540 P609942 P158914 B120470 P608116 * P608391 P608117 P158914 • Non Metal * Metal Liner

NEW

XRB Service Instructions

Engine Air Cleaners, Accessories & Service Parts 59

Medium

Dust Conditions

6 Inspect the new main filterBefore installing a new main or safety filter, inspect it carefully. Visually check for any voids, cuts, tears or indentations in the urethane-sealing surface. If your check reveals damage, do NOT install the filter.

7 Install the new filterThe critical sealing area will compress slightly, adjust itself and distribute the sealing pressure evenly. To complete a tight seal, apply pressure by hand at the outer rim of the filter, not the center.

8 Replace the cover & refasten the latchesReplace the service cover. The “INLET” arrow should line up with the air cleaner inlet. DO NOT force cover onto air cleaner. The cover should go on with no extra force. If cover is not flush to the body, the filter is not properly seated in the housing.

Never use the service cover to push the filter into place! Using the cover to push the filter

could cause damage to the housing and will void the warranty.

If the service cover hits the filter before it is fully in place, remove the cover and push the filter further into the housing and try again. The cover should go on with no extra force.

Refasten latches to secure cover. Make sure that latches penetrate the slots in both the body and the cover.

9 Inspect the intake systemInspect and torque all clamps, bolts and connections in the entire air intake system. Check for holes in piping, and repair if needed. If the Vacuator™ Valve is damaged, replace.

10 Restart your engine

1 Shut off your engine

2 Unlatch and remove service coverUnlatch and remove the service cover to access the main filter. Gently move the end of the filter back and forth to break the seal.

3 Remove the filterThe main filter makes such a tight seal, that you will encounter some initial resistance when trying to remove it. To break the seal, grab the end of the filter and gently move the filter back and forth and pull it out of the housing.

Avoid dislodging contaminant from the filter

or knocking it against the housing.

4 Clean the inside surfaceUsing a soft rag, remove all the dust and debris from the inside surface of the housing. Be careful not to introduce contaminant into the outlet tube.

Failure to do so may cause contaminant to be introduced to the seal area of the main filter during reinstallation, causing

a leak. Leaks result in higher restriction on the safety filter and shorter filter life.

5 Check the safety filter. Replace every third primary filter changeThe safety filter should be changed every third primary filter change out.

If the safety is not installed properly, it may attach itself to

the primary filter upon removal.

Dust from the main filter may be evident on the safety filter. This is normal. At each 1st and 2nd primary filter change, check safety filter for damage. If damaged, replace.

Also check to ensure the safety filter is properly seated in the housing. It should fit snugly inside the outlet tube. Continue pushing the filter into the outlet tube until it stops.

Recommended Main Filter Change IntervalChange the main filter when the restriction level reaches your vehicle/engine manufacturer recommendation.

2

3

Main Filter

5

Safety Filter

APPLICATION APPLICATION NOTENOTE

APPLICATION APPLICATION NOTENOTE

APPLICATION APPLICATION NOTENOTE

8

The “INLET” arrow should line up with the air cleaner inlet.

APPLICATION APPLICATION NOTENOTE

UNIQUE DESIGN CONCEPT

UNDED S

CCCCCOCOC N NEW NCEPTCCCCCCOCONW

60 Engine Air Cleaners, Accessories & Service Parts

Med

ium

Dus

t Con

ditio

ns

EPB - ERB2 Air Cleanerwith Full-View Pre-Cleaner

Specifications

See page 131 for the Full-View Pre-Cleaners

Full-View Pre-Cleaner

EPB Air Cleaner

See page 44-45 for EPB-ERB2 Service Parts

ERB2 Air Cleaner

NEW

Style Air Airflow Dimensions (mm) Cleaner Range Pre- Model No. m3/min. A B C D E F H J X° Cleaner M N O P

EPB B070005 2 - 4 182 334 76 76 45 27 115 145 340 H001249 77 187 42 158 EPB B080067 4 - 7 210 355 95 89 54 31,5 130 146 355 H000821 96 270 47 188 ERB2 B100126 7 - 12 259 430 114 102 143 52 205 0 400 H000823 115 270 47 188 ERB2 B130058 15 - 26 330 530 178 152 180 58 215 0 360 H002224 179 412 69 258 ERB2 B150058 18 - 32 381 590 178 178 136 70 241 102 540 H002224 179 412 69 258

X ° Free space needed to remove main element

62 Engine Air Cleaners, Accessories & Service Parts

Med

ium

Dus

t Con

ditio

ns

EPB - ERB2 Air Cleanerwith TopSpin™ Pre-Cleaner

Specifications

See page 132-133 for the TopSpin™ Pre-Cleaners See page 44-45 for EPB-ERB2 Service Parts.

UNIQUE DESIGN CONCEPT

UNDES

CCCCCOCOC N NEW NCEPTCCCCCCOCONW

EPB Air Cleaner

ERB2 Air Cleaner

TopSpin™ Pre-Cleaner

NEW

Style Air Airflow Dimensions (mm) Cleaner Range Pre- Model No. m3/min. A B C D E F H J X° Cleaner M N P

EPB B070005 2 - 5 182 334 76 76 45 27 115 145 340 H002437 77 162 146 EPB B080067 4 - 7 210 355 95 89 54 31,5 130 146 355 H002426 97 242 238 ERB2 B100126 7 - 12 259 430 114 102 143 52 205 0 400 H002427 116 242 238 ERB2 B130058 15 - 26 330 530 178 152 180 58 215 0 360 H002439 179 297 345 ERB2 B150058 18 - 32 381 590 178 178 136 70 241 102 540 H002439 179 297 345

X ° Free space needed to remove main element

IMPROVED

FPG Air Cleaner

64 Engine Air Cleaners, Accessories & Service Parts

Med

ium

Dus

t Con

ditio

ns

Advanced Sealing Technology in Compact Two-Stage DesignFor the Most Reliable Engine Protection

The FPG Air Cleaner series are two-stage full-plastic air cleaners with a built-in Pre-Cleaner and RadialSeal™ Sealing Technology.They are used on medium-duty applications line generator sets, agricultural tractors, bulldozers, drilling equipment, marine engines, trucks, loaders, backhoe, lifttruck, construction and industrial equipment. The FPG series offers improved reliability and durability with reduced weight and costs.

Ever since Donaldson developed the first air cleaner in 1915, we have worked closely with original equipment manufacturers to provide filtration solutions to meet changing design and specification requirements for diesel engines.

Because they are made of injection molded high-strength plastic, FPG air cleaners offer the flexibility to overcome space limitations for underhood air cleaners. Donaldson employs innovative plastic materials and production techniques that result in air cleaners that are corrosion-free and lighter in weight than traditional metal air cleaners - yet without sacrificing sturdiness. Our extensive vibration testing reveals this to be a more durable design than most metal air cleaners.

Despite its compact size, the FPG Air Cleaner offers complete engine air protection – removing 99.99+% of the dust and dirt particulate that enters the engine airstream.

The filter inside the air cleaner is also quite different from the traditional design: one-piece molded urethane endcaps encase the ends of the media and filter liners, eliminating the metal caps and plastisol potting compound that were traditionally used. The glued-on gasket found on conventional filters is gone – now, the inside surface of the open end is actually the radial sealing surface.

FPG Air Cleaner

Engine Air Cleaners, Accessories & Service Parts 65

Medium

Dust Conditions

Small, Durable and Corrosion-Free The World's Easiest to Service Air Cleaner

Filter Features

• Exclusive Radial Seal Sealing Technology means reliability and easy service - the filter is self-centering and self-aligning!

• One piece, molded urethane endcaps encase the filter media and liners - reducing components, adding reliability and lowering cost

Applications

• Provides up to 16 m³/min airflow per air cleaner - double throughput by using two units

• Installation can be horizontal, vertical, or even at an angle (as long as Vacuator™ Valve points down)

• 4", 5", 7", & 10" diameter sizes• Temperature tolerance:

to 83°C sustained (Do not install next to

turbocharger, muffler, exhaust pipes, or other high-temp component.)

Air Cleaner Features

• Easy to service! No tools needed! Usually done in 5 minutes or less!

• Durable plastic housing - corrosion-free and lightweight

• Two-stage air filtration! Built-in, tangential pre-cleaner ahead of primary filter removes up to 85% of incoming dust

• Choose 90° or straight outlet to fit your application

• Easy to fasten latches (no bolts!) retain dust cup/cover

• 45° Vacuator™ Valve orientation permits either vertical or horizontal air cleaner mounting (the dust cup can be incrementally rotated to suit specific application)

• Safety filter protects engine during in-field filter changeouts

• Already tapped to accept filter service indicator (see the Accessories section for indicator options)

• Indicator thread size = 1/8-27NPT (MALE)

Air inlet

Outlet to engine on this end

Injection molded plastic body is durable, corrosion-free and vibration-resistant

Dust removed in the first stage of cleaning is discharged automatically through the Vacuator™ Valve

Some models are available with the twist and lock cover design and called FPG Alexin™.See page 70-77.

FPG Air Cleaner

66 Engine Air Cleaners, Accessories & Service Parts

Med

ium

Dus

t Con

ditio

ns

FPG Specifications

Service Parts

FPG Air Cleaner

Engine Air Cleaners, Accessories & Service Parts 67

Medium

Dust Conditions

FPG Specifications - Service Parts

Air Cleaner Airflow Dimensions (mm) Model No. Range m³/min. A B C D E F H J L O P R S T X°

G042546 • 0,5 - 1 122 189 45 45 40 25 83 37 105 - - - - - 137

G042575 * • 0,5 - 1 122 189 45 45 40 25 83 37 105 - - - - - 137

G057502 * 1 - 3 146 300 51 51 42 25 100 43,5 115 - - - - - 300

G057504 1 - 3 146 300 51 51 42 25 100 43,5 115 - - - - - 300

G057505 • 1 - 3 146 300 51 51 42 25 100 43,5 115 - - - - - 300

G070006 * 2 - 5 182 330 76 76 45 27 115 43 138 - - - - - 330

G070059 * " 2 - 5 182 334 76 76 45 27 115 43 171 - - - - - 340

G070009 2 - 5 182 330 76 76 45 27 115 43 138 - - - - - 330

G070060 " 2 - 5 182 334 76 76 45 27 115 43 171 - - - - - 340

G082503 * 4 - 8 212 355 95 89 54 30 130 48 215 - - - - - 355

G082508 * 4 - 8 212 355 95 89 54 30 130 48 215 - - - - - 355

G082505 4 - 8,5 212 355 95 89 54 30 130 48 215 - - - - - 355

G100274 6 - 12 262 385 190 127 150 35 180 69 180 90 200 105 120 156 -

G100275 8 - 16 262 530 190 127 150 35 180 69 180 90 200 105 120 156 -

G100280* 6 - 11 262 385 190 127 150 35 180 69 180 90 200 105 120 156 -

* Includes safety element • High pulsation application X° Free space needed to remove the main element " Flat cover

Air Cleaner Main Safety Access Cover Vacuator™ Raincap Plastic Model No. Element Element Assy valve Mounting Band**

G042546 P822686 - P777153 P522958 H770066 P777151

G042575 P822686 P535396 P777153 P522958 H770066 P777151

G057502 P772578 P775298 P775308 P522958 H001377 P777730

G057504 P772578 - P775308 P522958 H001377 P777730

G057505 P775631 - P775308 P522958 H001377 P777730

G070006 P772579 P775300 P775311 P522958 H001379 P777731

G070009 P772579 - P775311 P522958 H001379 P777731

G070059 P772579 P775300 P778758 P522958 H001379 P777731

G070060 P772579 - P778758 P522958 H001379 P777731

G082503 P772580 P775302 P775305 P775569 H770010 P777732

G082505 P772580 - P775305 P775569 H770010 P777732

G082508 P772580 P775302 P775305 P522958 H770010 P777732

G100274 P777588 - P777589 P158914 P776343 Integrated

G100275 P777592 - P777593 P158914 P776343 Integrated

G100280 P777588 P777779 P777589 P158914 P776343 Integrated

* Spare Part only ** Only one mounting band needed per air cleaner

Med

ium

Dus

t Con

ditio

ns

FPG Alexin™ Air Cleaner

70 Engine Air Cleaners, Accessories & Service Parts

The FPG Alexin ™ Air Cleaner series are two-stage full-plastic air cleaners with a built-in Pre-Cleaner and RadialSeal™ Sealing Technology.

They are used on medium-duty applications line generator sets, agricultural tractors, bulldozers, drilling equipment, marine engines, trucks, loaders, backhoe, lifttruck, construction and industrial equipment. The FPG series offers improved reliability and durability with reduced weight and costs.

Ever since the introduction of the Donaldson RadialSeal™ product line in 1989 with the launch of the FPG Air Cleaner, Donaldson has developed many versions of this products and has continued to invest time and money in the further development of this RadialSeal filter concept, with the Alexin™ product line as one of the result.

The Donaldson Alexin brandname identifies Donaldson products using the proven, reliable Donaldson RadialSeal Technology for the filter elements combined with the ease of use of a Twist and Lock cover, that provides a convenient cover locking system with a design that saves space.

Advanced Sealing Technology in Compact Two-Stage Design For the Most Reliable Engine Protection

Despite its compact size, the FPG Air Cleaner offers complete engine air protection – removing 99.99+% of the dust and dirt particulate that enters the engine airstream.

FPG Alexin™ Air CleanerM

edium Dust Conditions

Engine Air Cleaners, Accessories & Service Parts 71

Small, Durable and Corrosion-Free The World's Easiest to Service Air Cleaner

Filter Features

• Exclusive Radial Seal Sealing Technology means reliability and easy service - the filter is self-centering and self-aligning!

• One piece, molded urethane endcaps encase the filter media and liners - reducing components, adding reliability and lowering costCover is unlocked with a yellow "finger", twisted to the left and•

removed from the filter housing. It's that simple! To fit the cover housing, just reverse the sequence. Only one mounting band is needed per body size.

Air inlet

Outlet to engine on this end

Injection molded plastic body is durable, corrosion-free and vibration-resistant

Dust removed in the first stage of cleaning is discharged automatically through the Vacuator™ Valve

Applications

• Provides up to 14 m³/min airflow per air cleaner - double throughput by using two units

• Installation can be horizontal, vertical, or even at an angle (as long as Vacuator™ Valve points down)

• 6", 8", 9", & 10" diameter sizes• Temperature tolerance:

to 83°C sustained (Do not install next to

turbocharger, muffler, exhaust pipes, or other high-temp component.)

Air Cleaner Features

• Easy to service! No tools needed! Usually done in 5 minutes or less!

• Durable plastic housing - corrosion-free and lightweight

• Two-stage air filtration! Built-in, tangential pre-cleaner ahead of primary filter removes up to 85% of incoming dust

• Choose 90° or straight outlet to fit your application

• Easy to fasten latches (no bolts!) retain dust cup/cover

• 45° Vacuator™ Valve orientation permits either vertical or horizontal air cleaner mounting (the dust cup can be incrementally rotated to suit specific application)

• Safety filter protects engine during in-field filter changeouts

• Already tapped to accept filter service indicator (see the Accessories section for indicator options)

• Indicator thread size = 1/8-27NPT (MALE)

Finger - molded, durableplastic to secure / lock the cover firmly to housing.

FPG Alexin™ Air Cleaner

72 Engine Air Cleaners, Accessories & Service Parts

Med

ium

Dus

t Con

ditio

ns

FPG Alexin™ Specifications

Air Cleaner Airflow Model No. Range Dimensions (mm) m³ /min. A B C D E F G H J L X°

G065497 "* 1,5 - 4 172 326 63,5 63,5 43,5 40,8 78 112 52 163 300 G065498 " 1,5 - 4 172 326 63,5 63,5 43,5 40,8 78 112 52 163 300 G065499 •* 1,5 - 4 172 326 63,5 63,5 43,5 82,2 - 112 52 163 300 G065500 • 1,5 - 4 172 326 63,5 63,5 43,5 82,2 - 112 52 163 300 G082580 "* 4 - 7,5 213 369 95 89 53,4 53,5 105 138 57 183 355 G082581 " 4 - 8 213 369 95 89 53,4 53,5 105 138 57 183 355 G082582 •* 4 - 7,5 213 369 95 89 53,4 83 - 138 57 183 355 G082583 • 4 - 8 213 369 95 89 53,4 83 - 138 57 183 355 G090219 "* 5 - 10 242 409 114 89 61,5 53,5 105 170 60 260 370 G090220 " 5 - 10 242 409 114 89 61,5 53,5 105 170 60 260 370 G090225 •* 5 - 10 242 409 114 101,5 61,5 87 - 170 60 260 370 G090226 • 5 - 10 242 409 114 101,5 61,5 87 - 170 60 260 370 G100317 "* 8 - 11 268 432 114 101,5 70,5 60,2 120 185 72 269 390 G100318 " 8 - 12 268 432 114 101,5 70,5 60,2 120 185 72 269 390 G100319 •* 8 - 11 268 432 114 101,5 70,5 87,5 - 185 72 269 390 G100320 • 8 - 12 268 432 114 101,5 70,5 87,5 - 185 72 269 390

" 90° elbow outlet * Includes safety element

• Straight outlet X ° Free space needed to remove main element

90° elbow outlet

Straight outlet

Service Parts

FPG Alexin™ Air Cleaner

Engine Air Cleaners, Accessories & Service Parts 73

Medium

Dust Conditions

FPG Alexin™ Service Parts

Air Cleaner Main Safety Access Cover Vacuator™ Raincap Plastic Model No. Element Element Assy valve Mounting Band**

G065497 P822768 P822769 P780401 P522958 H001378 P778810 G065498 P822768 - P780401 P522958 H001378 P778810 G065499 P822768 P822769 P780401 P522958 H001378 P778810 G065500 P822768 - P780401 P522958 H001378 P778810 G082580 P828889 P829333 P780403 P158914 H770010 P777732 G082581 P828889 - P780403 P158914 H770010 P777732 G082582 P828889 P829333 P780403 P158914 H770010 P777732 G082583 P828889 - P780403 P158914 H770010 P777732 G090219 P780522 P780523 P780524 P776008 H770012 P780532 G090220 P780522 - P780524 P776008 H770012 P780532 G090225 P780522 P780523 P780524 P776008 H770012 P780532 G090226 P780522 - P780524 P776008 H770012 P780532 G100317 P781039 P777639 P780578 P776008 H770012 P780594 G100318 P781039 - P780578 P776008 H770012 P780594 G100319 P781039 P777639 P780578 P776008 H770012 P780594 G100320 P781039 - P780578 P776008 H770012 P780594

** Only one mounting band needed per air cleaner * Spare Part only

FPG + FPG Alexin™Service Instructions

76 Engine Air Cleaners, Accessories & Service Parts

Med

ium

Dus

t Con

ditio

ns

4 Inspect the New Filter for DamageInspect the new filter carefully, paying attention to the inside of the open end, which is the sealing area. NEVER install a damaged filter. A new Donaldson radial seal filter may have a dry lubricant on the seal to aid installation.

5 Insert the New Radial Seal Filter ProperlyIf you’re servicing the safety filter, this should be seated into position before installing the primary filter.

Insert the new filter carefully. Seat the filter by hand, making certain it is completely into the air cleaner housing before securing the cover in place.

The critical sealing area will stretch slightly, adjust itself and distribute the sealing pressure evenly. To complete a tight seal, apply pressure by hand at the outer rim of the filter, not the flexible center. Avoid pushing on the center of the urethane end cap. No cover pressure is required to hold the seal. NEVER use the service cover to push the filter into place! Using the cover to push the filter in could cause damage to the housing, cover fasteners and will void the warranty.

If the service cover hits the filter before it is fully in place, remove the cover and push the filter (by hand) further into the air cleaner and try again. The cover should go on with no extra force.

Once the filter is in place, secure the service cover for the FPG models. For the FPG Alexin models, the cover is locked with a yellow "finger", twisted to the right.

6 Check Connectors for Tight FitMake sure that all mounting bands, clamps, bolts, and connections in the entire air cleaner system are tight. Check for holes in piping and repair if needed. Any leaks in your intake piping will send dust directly to the engine!

1 Remove the Filter Unfasten or unlatch the service cover for

the FPG models. For the FPG Alexin models, the cover is unlocked with a yellow "finger", twisted to the left and removed from the filter housing. Because the filter fits tightly over the outlet tube to create the critical seal, there will be some initial resistance, similar to breaking the seal on a jar. Gently move the end of the filter back and forth to break the seal then rotate while pulling

straight out. Avoid knocking the filter against the housing.

If your air cleaner has a safety filter, replace it every third primary filer change. Remove the safety filter as you would the primary filter. Make sure you cover the air cleaner outlet tube to avoid any unfiltered contaminant dropping into the engine.

Clean Both Surfaces of the Outlet Tube 2 and Check the Vacuator™ Valve Use a clean cloth to wipe the filter sealing surface and the inside of the outlet tube. Contaminant on the sealing surface could hinder an effective seal and cause leakage. Make sure that all contaminant is removed before the new filter is inserted. Dirt accidently transferred to the inside of the outlet tube will reach the engine and cause wear. Engine manufacturers say that it takes only a few grams of dirt to “dust” an engine! Be careful not to damage the sealing area on the tube.

If your air cleaner is equipped with a Vacuator Valve Visually check and physically squeeze to make sure the valve is flexible and not inverted, damaged or plugged.

Inspect the Old3 Filter for Leak CluesVisually inspect the old filter for any signs of leaks. A streak of dust on the clean side of the filter is a telltale sign. Remove any cause of leaks before installing new filter.

Wipe both sides of the outlet tube

clean.

Outer edge of the outlet tube

Inner edge of the outlet tube

NEVER use the service cover to push the filter into place! Using the cover to push the filter in could cause damage to the housing, cover fasteners and will void the warranty.

Caution

Rotate the filter while pulling straight out.

• Band has tabs on the inside circumference which fit exactly into notches on the FPG housing to hold the housing in position.• Tight fit between body and mounting band enhances components durability.• The springs compensate for dimensional changes due to temperature fluctuations, maintaining a tight fit.• Critical functions, i.e. Twist and Lock mechanism, remain unaffected.• Fool proof installation: bolts are tightened to predetermined height. The band is under tension at all times. More user friendly as the base is no longer split.• Donaldson polymer bands are completely non corrosive, lightweight, easy to install and economical.

Plastic Mounting Bands

Part Number Diameter Dimensions (mm) A B C D E

4" and 5" Mounting Bands for FPG Air Cleaners

P777151 4" 122 79 116 40 9 P777730 5" 146 90 136 50,5 9 6", 7", 8", 9" and 10" Mounting Bands for FPG Air Cleaners with Springloaded Screws

P778810 6" 171,5 99,5 153,5 50,5 9 P778901* 6" 171,5 99,5 90 50,5 9 P781831* 6" 171,5 99,5 93 50,5 9 P777731 7" 182 104,5 163 50,5 9 P777732 8" 211,5 119,5 190 50,5 9 P780580* 8" 211,5 119,5 110 50,5 9 P780378** 8" 212 119,5 110 85 9 P780532 9" 241 136 143 50,5 9 P780594 10" 268 149,5 143 80 11

* With insert M8 ** Double 8" Mounting Band needed

Designed Exclusively for the FPG + FPG Alexin™ Air Cleaners

FPG + FPG Alexin™Plastic Mounting Bands

Engine Air Cleaners, Accessories & Service Parts 77

Medium

Dust Conditions

4” and 5” Plastic Mounting Bands for FPG Air Cleaners.

6”, 7”, 8”, 9” and 10” Plastic Mounting Bands for FPG Air Cleaners with springloaded screws.

FTG Cycloflow™ Air Cleaner

78 Engine Air Cleaners, Accessories & Service Parts

Med

ium

Dus

t Con

ditio

ns

The FTG Cycloflow™ Air Cleaner is a two-stage air cleaner with built-in Pre-Cleaner and Axial Seal Sealing Technology. The air cleaner is mounted underhood with the service cover on the outside and an optional inlet hood on top.

Applications

• Allows 32-59 m³/min. airflow throughput per air cleaner

• Horizontal installation• Designed for large industrial

and construction machines: crawler tractors, crane loaders, excavators and air compressors with large engines operating in severe dust environments

• Sustained temperature tolerance: to 82°C

Air Cleaner Features

• Unique, flared inlet allows maximum airflow with low restriction

• 21" body diameters• Two-stage air cleaning deals with

very dusty environment: (1) Built-in louver spins air to separate up to 85% of incoming dust before it reaches the filter(2) Primary filter removes up to 99.99% of the remaining dust

• Built-in Vacuator™ Valve collects and releases pre-cleaned dust

• Safety filter on all models protects engine inlet during filter changeout

• Housing is metal and coated with a corrosion and chemical resistant polymer paint

• Indicator thread size = 1/8-27NPT (MALE)

Mounted Underhood Two-Stage Filtration for Large Construction & Mining Machines

Filter Features

Replacement filter choices include an extended service, high efficiency filter for restriction maintenance, and a standard life filter for scheduled maintenance

Accessories

• Each FTG is tapped to accept a filter service indicator• Order mounting bands, hoods, and other accessories separately

TangentialInlet

Outlet on this end

Vacuator™ Valve

Service Access Cover

FTG Cycloflow™ Air Cleaner

Engine Air Cleaners, Accessories & Service Parts 79

Medium

Dust Conditions

FTG Cycloflow™ Specifications - Service Parts

Air Cleaner Airflow Range Dimensions (mm) Model No. m³/min. A B C D E F H J L X°

G210007"* 32 - 59 546 613 254 254 150 90 330 146 442 613

G210010* 32 - 59 546 613 254 254 150 90 330 146 442 613

" Inlet on opposite side * Includes safety element X° Free space needed to remove main element

Service Parts

Air Cleaner Main Safety Vacuator™ Wing Gasket Raincap Mounting Model No. Element Element valve Nut Washer band*

G210007 P182040 P117781 P105220 P116175 H105740 H770082 H770068

G210010 P182040 P117781 P105220 P116175 H105740 H770082 H770068

* Two mounting bands needed per Air Cleaner

FTG Service Instructions

Engine Air Cleaners, Accessories & Service Parts 81

Medium

Dust Conditions

1 Remove the oldfilter gently“Baby” that dirty filter, until you get it clear of the housing. Accidentally bump-ing it while still inside means dropped dirt and dust that will contaminate the clean side of your filter housing, before the new filter element has a chance to do its job.

2 Always clean the inside of the housing carefullyDirt left in the air cleaner housing spells death for your engine. Use a clean, damp cloth to wipe every surface clean. Check it visually to make sure it's clean before putting in a new filter.

3 Always clean the gasket sealing surfacesAn improper gasket seal is one of the most common causes of engine contamination. Make sure that all hardened dirt ridges are completely removed, both on the bottom and top of the air cleaner housing.

4 Check for unevendirt patternsYour old filter has valuable cluesto dust leakage or gasket sealing problems. A pattern on the filter clean side is a sign that the old filter was not firmly sealed or that a dust leak exists. Identify the cause of that leak and rectify it before installing a new filter.

5 Press your fresh gasket to see that it springs backMake sure your new filter is made with a highly com-pressible gasket that springs back (promptly) when fin-ger pressure is released. A high quality gasket is one of the most important parts of the filter.

6 Make sure the gasket seats evenlyIf you don’t feel the gasket seating evenly for a perfect seal, you don’t have protection.Re-check to see if the sealing surface in the housing is clean, and ensure that the filter is the correct model. It may be the wrong size for the housing.

7 Ensure air-tight fit on all connections and ductsCheck that all clamps and flange joints are tight, as well as the air cleaner mounting bolts. Seal any leaks immediately - leaks mean dirt is directly entering your engine.

FRG2 Air Cleaner

82 Engine Air Cleaners, Accessories & Service Parts

Med

ium

Dus

t Con

ditio

ns

Superior Protection for Larger Engines RadialSeal Sealing Technology Means Reliable Filtration and Quicker Service

The FRG2 Air Cleaners is a two-stage hybrid air cleaner with RadialSeal™ Sealing Technology. Ideal for medium- to heavy duty applications like construction equipment, agricultural machinery, mining equipment and off-highway vehicles.The FRG2 Air Cleaner is the Next Generation FRG Air Cleaner Product featuring Donaldson's Unique Design Concept.

For more details on this UDC Feature, see page 7.

Applications FRG2

• Horizontal mount required• Provides variety of airflow volumes to engine: from 6.5 to 51 m³/min.• Temperature tolerance: to 83°C continuous / 105°C intermittent• Body diameters of 10", 11", 13", 15" and 18"

Features FRG2

• Two stage filter system: the first stage removes up to 85% of incoming dust• Vacuator™ Valve automatically releases the pre- cleaned dust• Proven RadialSeal™ Technology• Tapped for restriction indicator as standard (Except for G180075)• Durable, long-lasting finish. Comprised of two materials: injection molded, high strength polymer service cover and a metal body (the service cover is accessed by latches)• Indicator thread size = 1/8-27NPT (MALE)

• Mounting the unit directly to the engine is not recommended; excessive engine vibration can cause premature air cleaner structural failure• Cost effective / Compact and light• Flexible installation • Durable, high-tech and easy to service design

Accessories

Donaldson intake accessories for your FRG2 Air Cleaner can help overcome or prevent various problems. For instance:• Mounting bands for FRG2s must be ordered

separately• If the installed air cleaner will be exposed to

rain, snow or debris, an inlet cap can prevent moisture ingestion.

• A service indicator measures the airflow restriction across the filter, thereby showing how much useful life the filter has left, and when to replace the filter cartridge (see Accessories section of this catalogue).

t directly to the engine is notxcessive engine vibration can

UNIQUEDESIGNCONCEPT

UD

CO NEW

Patent Pending for Donaldson's Unique Design Concept.

FRG2 Air Cleaner

Engine Air Cleaners, Accessories & Service Parts 83

Medium

Dust Conditions

FRG2 Specifications

ØC

J

H

FRG2 FRGAir Cleaners

G100420 G100281 G100428 G100284 G110381 G110211 G110382 G110269 G130236 G130120 G130232 G130061 G130234 G130088 G130233 G130087 G130235 G130113 G150255 G150092 G150259 G150112 G150256 G150097 G180087 G180033 G180074 G180035 G180073 G180031 G180075 G180038

Replaces

Air Cleaner Airflow Model No. Range Dimensions (mm) m³/min. A B C D E F H J L X° Z°°

G100420 * 7 - 14 259 430 114 101 90 52 205 68 270 373 107 G100428 7 - 16 259 430 114 101 90 52 205 68 270 373 107 G110381 " * 8 - 16 279 480 127 114 108 67 191 77 275 373 107 G110382 * 8 - 16 279 480 127 114 108 67 191 77 275 373 107 G130236 * 10 - 18 330 425 152 127 132 58 216 90 301 365 93 G130232 * 13 - 24 330 530 152 127 132 58 216 90 301 470 93 G130234 " * 13 - 24 330 530 152 127 132 58 216 90 301 470 93 G130233 13 - 25 330 530 152 127 132 58 216 90 301 470 93 G130235 " 13 - 25 330 530 152 127 132 58 216 90 301 470 93 G150255 * 16 - 32 381 530 178 152 140 70 242 103 338 480 93 G150259 " * 16 - 32 381 530 178 152 118 70 242 103 338 480 93 G150256 16 - 33 381 530 178 152 140 70 242 103 338 480 93 G180087 * 20 - 42 457 510 203 178 128 85 290 128 402 460 130 G180074 * 22 - 46 457 650 203 178 128 85 290 128 402 600 130 G180073 * 25 - 51 457 650 203 203 128 85 290 128 402 600 130 G180075 " * • 25 - 51 457 650 203 203 128 85 290 128 402 600 130 " Inlet on opposite side * Includes safety element X° Free space needed to remove main element Z°° Free space needed to remove cover • No built-in tap for filter service indicator

ØD ØA

FB

E

X

UNIQUE DESIGN CONCEPT

UNDE

CCCCOCC N NEW

FRG2 Air Cleaner

84 Engine Air Cleaners, Accessories & Service Parts

Med

ium

Dus

t Con

ditio

ns

FRG2 Service Parts

Service Parts

Air Cleaner Main Kit Access Vacuator™ Rain Mounting Model No. Element Number • Cover Assy* Valve Cap band**

G100420 P785589 X770689 P784944 P776008 H770012 P004076 G100428 P785589 - P784944 P776008 H770012 P004076 G110381 P785396 X770690 P784923 P158914 H770013 P004079 G110382 P785396 X770690 P784923 P158914 H770013 P004079 G130232 P785390 X770691 P784892 P776008 H770090 P013722 G130233 P785390 - P784892 P776008 H770090 P013722 G130234 P785390 X770691 P784892 P776008 H770090 P013722 G130235 P785390 - P784892 P775569 H770090 P013722 G130236 P785398 X770692 P784892 P776008 H770090 P013722 G150255 P785590 X770693 P785551 P776008 H770089 P016845 G150256 P785590 - P785551 P776008 H770089 P016845 G150259 P785590 X770693 P785551 P776008 H770089 P016845 G180073 P785394 X770688 P784792 P105220 H001053 H770037 G180074 P785394 X770688 P784792 P105220 H001053 H770037 G180075 P785394 X770688 P784792 P105220 H001053 H770037 G180087 " P786197 X770683 P784792 P105220 H001053 H770037

* Spare Part only ** Two mounting band needed per Air Cleaner " No restriction indicator tapping point • Safety element can only be bought as a kit meaning together with the main element

FRG2 Service Instrcutions

88 Engine Air Cleaners, Accessories & Service Parts

Med

ium

Dus

t Con

ditio

ns

4 Inspect the New Filter for DamageInspect the new filter carefully, paying attention to the inside of the open end, which is the sealing area. NEVER install a damaged filter. A new Donaldson radial seal filter may have a dry lubricant on the seal to aid installation.

5 Insert the New Radial Seal Filter ProperlyIf you’re servicing the safety filter, this should be seated into position before installing the primary filter.

Insert the new filter carefully. Seat the filter by hand, making certain it is completely into the air cleaner housing before securing the cover in place.

The critical sealing area will stretch slightly, adjust itself and distribute the sealing pressure evenly. To complete a tight seal, apply pressure by hand at the outer rim of the filter, not the flexible center. Avoid pushing on the center of the urethane end cap. No cover pressure is required to hold the seal. NEVER use the service cover to push the filter into place! Using the cover to push the filter in could cause damage to the housing, cover fasteners and will void the warranty.

If the service cover hits the filter before it is fully in place, remove the cover and push the filter (by hand) further into the air cleaner and try again. The cover should go on with no extra force.

Once the filter is in place, secure the service cover.

6 Check Connectors for Tight FitMake sure that all mounting bands, clamps, bolts, and connections in the entire air cleaner system are tight. Check for holes in piping and repair if needed. Any leaks in your intake piping will send dust directly to the engine!

1 Remove the Filter Unfasten or unlatch the service cover.

Because the filter fits tightly over the outlet tube to create the critical seal, there will be some initial resistance, similar to breaking the seal on a jar. Gently move the end of the filter back and forth to break the seal then rotate while pulling straight out. Avoid knocking the filter against the housing.

If your air cleaner has a safety filter, replace it every third primary filer change. Remove the safety filter as you would the primary filter. Make sure you cover the air cleaner outlet tube to avoid any unfiltered contaminant dropping into the engine.

Clean Both Surfaces of the Outlet Tube 2 and Check the Vacuator™ Valve Use a clean cloth to wipe the filter sealing surface and the inside of the outlet tube. Contaminant on the sealing surface could hinder an effective seal and cause leakage. Make sure that all contaminant is removed before the new filter is inserted. Dirt accidently transferred to the inside of the outlet tube will reach the engine and cause wear. Engine manufacturers say that it takes only a few grams of dirt to “dust” an engine! Be careful not to damage the sealing area on the tube.

If your air cleaner is equipped with a Vacuator Valve Visually check and physically squeeze to make sure the valve is flexible and not inverted, damaged or plugged.

Inspect the Old3 Filter for Leak CluesVisually inspect the old filter for any signs of leaks. A streak of dust on the clean side of the filter is a telltale sign. Remove any cause of leaks before installing new filter.

Wipe both sides of the outlet tube

clean.

Outer edge of the outlet tube

Inner edge of the outlet tube

NEVER use the service cover to push the filter into place! Using the cover to push the filter in could cause damage to the housing, cover fasteners and will void the warranty.

Caution

Rotate the filter while pulling straight out.

Heavy Dust Conditions

Heavy Dust ConditionsAir Cleaners used in

... Donaldson offers a full line of air cleaners for a wide variety of applications and operating environments.

Engine Air Cleaners, Accessories & Service Parts 89

UNIQUE DESIGN CONCEPT

UNDE

CCCCCCCON NEW NCEPTCCCCCCCON

NEW

Section Index

FLB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90FLB Service Instructions . . . . . . . . . . . . . . . . . . . 92EPB-ERB2 with Donaspin™ Pre-Cleaner . . . . . 93EPB-ERB2 with Strata™ Pre-Cleaner . . . . . . . . 95SPB2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97SRB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100SPB2-SRB Service Instructions. . . . . . . . . . . . 103SSG Donaclone™ . . . . . . . . . . . . . . . . . . . . . . . . 104SSG Service Instructions . . . . . . . . . . . . . . . . . 110STG Donaclone™ . . . . . . . . . . . . . . . . . . . . . . . . 111 STG Service Instructions . . . . . . . . . . . . . . . . . 117

FLB Air Cleaner

90 Engine Air Cleaners, Accessories & Service Parts

Heav

y Du

st C

ondi

tions

Two-Stage Louvered Body Air Cleaner

The FLB - Louvered Body Air Cleaner is a two-stage air cleaner with scavenge exhaust system and Axial Seal Sealing Technology. Body diameters in 6", 8", 10" and 12". Handles airflows of 3-17 m³/min. Sustained temperature tolerance: to 82°C.

Designed especially for combines and other heavy-duty construc-tion and agricultural equipment operating in severe dust, fibers, lint and shaft environments. To be used with an exhaust ejector.For all available Donaldson Exhaust Ejectors, see page 124-125.

Air Cleaner Airflow Range Dimensions (mm) Model No m³/min. A B D F G X°

B065018 3 - 5 167 360 76 28 32 345 B080022 4,5 - 7 203 423 89 54 32 415 B100067 7 - 12 259 430 101 50 32 425 B120260 12 - 17 300 424 127 80 32 415 X° Free space needed to remove main element

Air Cleaner Main Safety Mounting Filter Model No. Element Element Band* Wing Nut

B065018 P772565 P770207 P007191 P138403 B080022 P772556 P119410 P004307 P138403 B100067 P772530 P133138 P004076 P138403 B120260 P772520 P770678 H000349 P134803

* Two mounting bands needed per Air Cleaner

FLB Specifications - Service Parts

Service Parts

FLB Service Instructions

92 Engine Air Cleaners, Accessories & Service Parts

Heav

y Du

st C

ondi

tions

1 Remove the oldfilter gently“Baby” that dirty filter, until you get it clear of the housing. Accidentally bump-ing it while still inside means dropped dirt and dust that will contaminate the clean side of your filter housing, before the new filter element has a chance to do its job.

2 Always clean the inside of the housing carefullyDirt left in the air cleaner housing spells death for your engine. Use a clean, damp cloth to wipe every surface clean. Check it visually to make sure it's clean before putting in a new filter.

3 Always clean the gasket sealing surfacesAn improper gasket seal is one of the most common causes of engine contamination. Make sure that all hardened dirt ridges are completely removed, both on the bottom and top of the air cleaner housing.

4 Check for unevendirt patternsYour old filter has valuable cluesto dust leakage or gasket sealing problems. A pattern on the filter clean side is a sign that the old filter was not firmly sealed or that a dust leak exists. Identify the cause of that leak and rectify it before installing a new filter.

5 Press your fresh gasket to see that it springs backMake sure your new filter is made with a highly com-pressible gasket that springs back (promptly) when fin-ger pressure is released. A high quality gasket is one of the most important parts of the filter.

6 Make sure the gasket seats evenlyIf you don’t feel the gasket seating evenly for a perfect seal, you don’t have protection.Re-check to see if the sealing surface in the housing is clean, and ensure that the filter is the correct model. It may be the wrong size for the housing.

7 Ensure air-tight fit on all connections and ductsCheck that all clamps and flange joints are tight, as well as the air cleaner mounting bolts. Seal any leaks immediately - leaks mean dirt is directly entering your engine.

Engine Air Cleaners, Accessories & Service Parts 93

Heavy Dust Conditions

EPB – ERB2 Air Cleanerwith Donaspin™ Pre-Cleaner

Specifications

UNIQUE DESIGN CONCEPT

UNDES

CCCCCOCOC N NEW NCEPTCCCCCCOCONW

See page 130 for the Donaspin™ Pre-Cleaners

Donaspin™ Pre-Cleaner

EPB Air Cleaner

See page 44-45 for EPB-ERB2 Service Parts.

ERB2 Air Cleaner

NEW

Style Air Airflow Dimensions (mm) Cleaner Range Pre- Model No. m³/min. A B C D E F H J X° Cleaner M N O P Q

EPB B070005 2 - 5 182 334 76 76 45 27 115 145 340 H001212 77 203 305 316 55 EPB B080067 4 - 7 210 355 95 89 54 31,5 130 146 355 H001307 95 203 305 304 42 ERB2 B100126 7 - 12 259 430 114 102 143 52 205 0 400 H001215 114 203 305 290 28 X ° Free space needed to remove main element For all available Donaldson Exhaust Ejectors, see page 124-125

Engine Air Cleaners, Accessories & Service Parts 95

Heavy Dust Conditions

EPB – ERB2 Air Cleanerwith Strata™ Pre-Cleaner

Specifications

UNIQUE DESIGN CONCEPT

UNDED S

CCCCCOCOC N NEW NCEPTCCCCCCOCONW

For more details on the Strata™ Pre-Cleaner, contact your Donaldson representative.

EPB Air Cleaner

See page 44-45 for EPB-ERB2 Service Parts.

ERB2 Air Cleaner

Strata™ Pre-Cleaner

NEW

Style Air Airflow Dimensions (mm) Cleaner Range Pre- Model No. m3/min. A B C D E F H J X° Cleaner M N O P Q

EPB B070005 2 - 4 182 334 76 76 45 27 115 145 340 H000975 78 167 281 441 25 EPB B080067 4 - 7 210 355 95 89 54 31,5 130 146 355 H000896 97 167 281 447 25 ERB2 B100126 7 - 12 259 430 114 102 143 52 205 0 400 H001510 116 167 281 441 25 ERB2 B130013 15 - 26 330 530 178 152 180 58 215 0 360 H001148 179 279 406 465 38 ERB2 B150025 18 - 32 381 590 178 178 136 70 241 102 540 H001148 179 279 406 465 38

X° Free space needed to remove main element For all available Donaldson Exhaust Ejectors, see page 124-125

Heavy Dust Conditions

SPB2 Air Cleaner

Engine Air Cleaners, Accessories & Service Parts 97

Two-Stage RadialSeal™ Air Cleaners which offer emproved reliabilityand durability, reduced weight and costs and better serviceability

The SPB2 Air Cleaner is a two-stage full plastic air cleaner with built-in high efficiency Pre-Cleaner and RadialSeal™ Sealing Technology. They are suitable for agricultural and construction equipment operating in severe dust environments. To be used with an exhaust ejector. For all available Donaldson Exhaust Ejectors, see page 124.125.

The SPB2 Air Cleaner Products are featuring the Donaldson's Unique Design Concept. For more details on this UDC Feature, see page 7.

Applications SPB2

• Can be mounted vertically or horizontally• Provides variety of airflow volumes to engine: from 6 to 22 m³/min.• Temperature tolerance: to 83°C continuous / 105°C intermittent

Features SPB2

Body diameter of 13"• • Cost effective / Compact and light weight• Flexible installation • Reliable, durable, high-tech and easy to service design• Proven RadialSeal™ Technology• Tapped for restriction indicator as standard

Built-in Strata™ Pre-Cleaner with efficiency of 90 - 93%• Always to be used with a scavenge system (minimum with 10% scavenge)• ISO Coarse Dust / ISO 5011 Certificate•

• Indicator thread size = 1/8-27NPT (MALE)

UNIQUE DESIGN CONCEPT

UD

CCCCO NEW ONCEPTCCCCO

Patent Pending for Donaldson's Unique Design Concept.

Heav

y Du

st C

ondi

tions

98 Engine Air Cleaners, Accessories & Service Parts

SPB2 Specifications

SPB2 Air Cleaner

1) 4 Clips M8 optional – Reference P784517: Plastic bag with 4 U-Clips2) Insert M83) 1/8 27 NPT

B130048

B130060

Heavy Dust Conditions

Engine Air Cleaners, Accessories & Service Parts 99

SPB2 Specifications - Service Parts

SPB2 Air Cleaner

B130048 + B130060 Dimensions (mm) A B C D E F G H I J K L M N O X Z

325 481 328 266 234 127 30 38 33 133 89 306 114 110 182 75 280

X Free space needed to remove main element Z Free space needed to remove cover Airflow = 6-22 m³/min.

Air Cleaner Main Kit Access Cover Mounting Model No. Element Number • Assy* band**

B130048 P783543 X770684 P783693 Integrated B130060 " P783543 X770684 P783693 Integrated

* Spare Part only ** Two mounting bands needed per air cleaner " Inlet 180° rotated • Safety Element can only be bought as a kit meaning together with the main element For all available Exhaust Ejectors, see page 124-125

Service Parts

100 Engine Air Cleaners, Accessories & Service Parts

Two-Stage RadialSeal™ Air Cleaners which offer improved reliability and durability, reduced weight and costs and better serviceability.

The SRB Air Cleaner is a two-stage hybrid air cleaner with built-in high efficiency Pre-Cleaner and RadialSeal™ Sealing Technology.

They are suitable for agricultural and construction equipment operating in severe dust environments.

To be used with an exhaust ejector. For all avail-able Donaldson Exhaust Ejectors, see page 124.125.

Applications SRB

• Can be mounted vertically or horizontally• Provides variety of airflow volumes to engine: from 4 to 18 m³/min.• Temperature tolerance: to 83°C continuous / 105°C intermittent.

Features SRB

• Body diameter of 9", 10", 11" and 13".Cost effective / Compact and light weight•

• Flexible installation • Reliable, durable, high-tech and easy to service design• Proven RadialSeal™ Technology• Tapped for restriction indicator as standard

Built-in Strata™ Pre-Cleaner with efficiency of 90 - 93%• Always to be used with a scavenge system (minimum with 10% scavenge)• ISO Coarse Dust / ISO5011 Certificate•

• Indicator thread size = 1/8-27NPT (MALE)

SRB Air CleanerHe

avy

Dust

Con

ditio

ns

Engine Air Cleaners, Accessories & Service Parts 101

SRB Specifications - Service Parts

Air Cleaner Airflow Range Dimensions (mm) Model No. m³/min. A B C D E F G H X° Z°°

B095437" 4 - 8 229 400 166 102 203 61 - 268 75 380 B100121 8 - 12 259 430 166 102 179 52 - 268 75 380 B110155 11 - 15 279 480 166 114 175 67 - 278 75 380 B130046 13 - 18 330 530 140 127 25 58 332 335 60 530 X° Free space needed to remove main element Z °° Free space needed to remove cover "90° elbow

Air Cleaner Main Safety Access Mounting Model No. Element Element Cover Assy* band**

B095437 P780522 P780523 P782176 P004073 B100121 P771039 P777639 P777998 P004076 B110155 P778905 P778906 P783014 P004079 B130046 P777279 P777414 P781124 P013722

* Spare Part only ** Two mounting bands needed per Air Cleaner

B095437 - B100121 - B110155

B130046

SRB Air CleanerHeavy Dust Conditions

Engine Air Cleaners, Accessories & Service Parts 103

SPB2 - SRB Service Instructions

Heavy Dust Conditions

4 Inspect the New Filter for DamageInspect the new filter carefully, paying attention to the inside of the open end, which is the sealing area. NEVER install a damaged filter. A new Donaldson radial seal filter may have a dry lubricant on the seal to aid installation.

5 Insert the New Radial Seal Filter ProperlyIf you’re servicing the safety filter, this should be seated into position before installing the primary filter.

Insert the new filter carefully. Seat the filter by hand, making certain it is completely into the air cleaner housing before securing the cover in place.

The critical sealing area will stretch slightly, adjust itself and distribute the sealing pressure evenly. To complete a tight seal, apply pressure by hand at the outer rim of the filter, not the flexible center. Avoid pushing on the center of the urethane end cap. No cover pressure is required to hold the seal. NEVER use the service cover to push the filter into place! Using the cover to push the filter in could cause damage to the housing, cover fasteners and will void the warranty.

If the service cover hits the filter before it is fully in place, remove the cover and push the filter (by hand) further into the air cleaner and try again. The cover should go on with no extra force.

Once the filter is in place, secure the service cover.

6 Check Connectors for Tight FitMake sure that all mounting bands, clamps, bolts, and connections in the entire air cleaner system are tight. Check for holes in piping and repair if needed. Any leaks in your intake piping will send dust directly to the engine!

1 Remove the Filter Unfasten or unlatch the service cover.

Because the filter fits tightly over the outlet tube to create the critical seal, there will be some initial resistance, similar to breaking the seal on a jar. Gently move the end of the filter back and forth to break the seal then rotate while pulling straight out. Avoid knocking the filter against the housing.

If your air cleaner has a safety filter, replace it every third primary filer change. Remove the safety filter as you would the primary filter. Make sure you cover the air cleaner outlet tube to avoid any unfiltered contaminant dropping into the engine.

Clean Both Surfaces of the Outlet Tube 2 and Check the Vacuator™ Valve Use a clean cloth to wipe the filter sealing surface and the inside of the outlet tube. Contaminant on the sealing surface could hinder an effective seal and cause leakage. Make sure that all contaminant is removed before the new filter is inserted. Dirt accidently transferred to the inside of the outlet tube will reach the engine and cause wear. Engine manufacturers say that it takes only a few grams of dirt to “dust” an engine! Be careful not to damage the sealing area on the tube.

If your air cleaner is equipped with a Vacuator Valve Visually check and physically squeeze to make sure the valve is flexible and not inverted, damaged or plugged.

Inspect the Old3 Filter for Leak CluesVisually inspect the old filter for any signs of leaks. A streak of dust on the clean side of the filter is a telltale sign. Remove any cause of leaks before installing new filter.

Wipe both sides of the outlet tube

clean.

Outer edge of the outlet tube

Inner edge of the outlet tube

NEVER use the service cover to push the filter into place! Using the cover to push the filter in could cause damage to the housing, cover fasteners and will void the warranty.

Caution

Rotate the filter while pulling straight out.

104 Engine Air Cleaners, Accessories & Service Parts

SSG Donaclone™ Air CleanerHe

avy

Dust

Con

ditio

ns

Covered by issued and pending patents, both U.S. and Internationally

Mounting (back) side view of an SSG 29 model

The large, massive mining vehicle in the picture above is an ideal match for the Donaldson SSG Air Cleaner.

Design ImprovementsThe SSG Air Cleaner has filters • that use RadialSeal™ Sealing Technology, compared to axial seal style filters. This single design improvement eliminates the need to replace filter and cover gaskets - less service time and fewer parts to inventory.

The access cover for filter • service now has quick release cover latches and a chain that connects the air cleaner service cover to the housing!

The SSG Air Cleaner offers design improvements and therefore replaces our older SRG Air Cleaner models.

SRG Model SSG ModelG200008 G200087G200013 G200086G290000 G290057G290023 G290052G290012 G290053

Designed for the Worst Dust Conditions New Choice for Construction and Off-Highway Applications

s NEW

Mounting (back) side view of an SSG 20 model

Engine Air Cleaners, Accessories & Service Parts 105

SSG Donaclone™ Air CleanerHeavy Dust Conditions

Powerful Two-Stage FiltrationThe first stage of this powerful air cleaner consists of hundreds of our exclusive, patented Donaclone™ pre-cleaner tubes (over 130 tubes in the SSG 20 and over 250 tubes in the SSG 29 models). Each tube spins the incoming air to create a centrifugal force that separates up to 97% of the dust and dirt in the airstream (see image on right). Donaclone™ tubes have no moving parts – so there is nothing to break down or maintain. They function properly whenever the engine is running.

The pre-cleaned dust is automatically ejected from the dust cup with a Vacuator™ Valve located below in the lower housing body, below the Donaclone tubes.

The second stage of filtration is the primary filter. A safety filter, which fits inside the primary filter, is standard on all models for protection during primary filter changeout.

Applications• Allows 48 to 68 m³/min. airflow

throughput for the SSG 20 model and 73 to 135 m³/min. airflow throughput for the SSG 29 models

• Horizontal installation• Off-road, heavy or extreme dust

conditions• Ideal for scrapers, earth movers,

graders

Air Cleaner Features• Single and dual outlet models - two

high-flow models available• Inlet has perforated holes on three

sides; rain shrouds available if required

• Filters have urethane end caps with radial seal sealing technology

• Built-in pre-cleaning tubes separate up to 97% of the in-coming dust

• Latch-style cover with attached safety chain for faster and simpler filter service

• Constructed of heavy-gauge steel with a primed, ready-to-paint finish

• Same overall package size as older Donaldson SRG axial seal style housings

• Drop down tube accessory available simplifies routine air cleaner inspections

• Indicator thread size = 1/8-27NPT (MALE)

Filter Features• Replacement main filter choices:

Standard life filters (for scheduled maintenance) and Donaldson Endurance™ extended service high efficiency filters. Air cleaners ship with the standard filters.

• Grab handles on the main filter to help remove the loaded filter during service

• Safety filter on all models

The large, massive mining vehicle in the picture above is an ideal match for the Donaldson SSG Air Cleaner.

Side view of three Donaclone pre-cleaning tubes.

Versatile SSG Provides Airflow to 135 m³/min. With Improved Design Features Compared to our Older SRG Model

Heav

y Du

st C

ondi

tions

106 Engine Air Cleaners, Accessories & Service Parts

SSG Donaclone™ Air Cleaner

Front View Dual Outlet Front View Single Outlet Side View Dual and Single

A

H

OUTLETOUTLET

INLETINLET

C

DF

K

IINLETINLET

J

INLETINLET

J

INLETINLET

H

SSG Specifications

Air Cleaner Airflow Range Dimensions (mm)

Model No. m³/min. A C D F H I J K

G200087 48 - 56 500 203 665 76 1274 559 533 400 G200086 50 - 58 500 254 665 76 1274 559 533 400 G200088* 59 - 68 500 254 798 76 1274 686 533 597

G290057 73 - 85 500 203 665 76 1255 559 1092 400 G290052 95 - 108 500 203 665 76 1255 559 1092 400 G290053 102 - 116 500 254 665 76 1255 559 1092 400 G290055* 119 - 135 500 254 798 76 1255 686 1092 597

* Sized to accomodate higher airflow

Single Outlet Models

Dual Outlet Models

Heavy Dust Conditions

Engine Air Cleaners, Accessories & Service Parts 107

SSG Donaclone™ Air Cleaner

NEW NOTES:3 = Shipped with air cleaner initially

Outlet to engine at rear of unit

Mounting brackets on back edges of unit

Primary filter, Radial Seal

Dust Cup AssemblyP158089 (includes all 4 parts shown)

Air Inlet Perforations on three sides of the lower body

Optional rain shrouds for 3 outward facing sides

Service cover with safety chain (approx. 10")

Donaclone pre-cleaning tubes

GasketsG200086, G200087two, short strips P115098two, long strips P117791

G200088two, short strips P603504two, long strips P117791

G200086, G200087rain shroud, right side P119874rain shroud, front P119876rain shroud, left side P119875

G200088rain shroud, right side P610776rain shroud, front P119876rain shroud, left side P610777

Dust Cup ClampP100808

Dust Cup GasketP017804

cover P603716cover chain P017281chain connector P017283

Lower Body Assembly G200086, G200087 - P117785

G200088 - P603505

G200086, G200087P608306(3)P185152, extended life

G200088P609519(3)P185153, extended life

G200086, G200087P608305(3)

G200088P609518(3)

Vacuator ValveP103198

Drop Down Tube ExtensionHow it works: When installed on the dust cups on the lower assembly, the rubber connector vibrates during normal vehicle operation and gravity expels the pre-cleaned dust.• Improves dust evacuation from the air cleaner• Clear tube allows for visual inspection of dust

collection • Reduces air cleaner inspection time• Ships fully assembled• Proper conversion requires drop down tube for

every dust cup

For more information features and dimensions, see the Accessories Section.

Drop Down Tube Kit X006561

Part No. X006561

Single Outlet Model - SSG 20 Service Parts

61

NEW

G290052, G290053, G290057P608305(3)

G290055P609518(3)

Dual Outlet Model - SSG 29 Service Parts

NOTES: 3 = Shipped with air cleaner initially

Outlet to engine at rear of unit

Mounting brackets on back edges of unit

Optional rain shrouds for 3 outward facing sides

Service coverwith safety chain(approx. 10")

Donaclone pre-cleaning tubes

Gasket

Air Inlet Perforations on three sides of the lower body

Primary Filter, Radial Seal

Safety Filter Radial Seal

G290052, G290053, G290057P608306(3)P185152, extended life

G290055P609519(3)P185153, extended life

Dust cup assemblyP158089(3)

(includes all 4 parts shown)

Dust Cup ClampP100808

Dust Cup GasketP017804

G290052, G290053, G290057rain shroud, right side P119874rain shroud, front P119877rain shroud, left side P119875

G290055rain shroud, right side P610776rain shroud, front P119877rain shroud, left side P610777

cover P603716cover chain P017281chain connector P017283

G290052, G290053, G290057two, short strips P115098two, long strips P115096

G290055two, short strips P603504two, long strips P115096

Lower Body Assembly G290052, G290053 - P118552

G290057 - P115110

G290055 - P609508

Vacuator ValveP103198

Drop Down Tube Kit X006561 (3 req'd)

Drop Down Tube ExtensionHow it works: When installed on the dust cups on the lower assembly, the rubber connector vibrates during normal vehicle operation and gravity expels the pre-cleaned dust.• Improves dust evacuation from the air cleaner• Clear tube allows for visual inspection of dust

collection • Reduces air cleaner inspection time• Ships fully assembled• Proper conversion requires drop down tube for

every dust cup

For more information features and dimensions, see the Accessories Section. Part No. X00656161

NEW

Heav

y Du

st C

ondi

tions

108 Engine Air Cleaners, Accessories & Service Parts

SSG Donaclone™ Air Cleaner

Heav

y Du

st C

ondi

tions

110 Engine Air Cleaners, Accessories & Service Parts

SSG Donaclone™ Service Instructions

5 Inspect the New Filter before Installing

Inspect the new filter carefully, paying attention to the inside of the open end, which is the sealing area. NEVER install a damaged filter. A new Donaldson radial seal filter may have a dry lubricant on the seal to aide installation.

6 Insert New Radial Seal Filter Properly

If you are servicing the safety filter, this should be seated into position before installing the primary filter.

Insert the new filter carefully by hand, making certain it is completely seated into the air cleaner housing before securing the cover in place.

The critical sealing area will compress slightly, adjust itself and distribute the sealing pressure evenly. To complete a tight seal, apply pressure by hand at the outer rim of the filter, not the flexible center. (Avoid pushing on the center of the end cap.) No cover pressure is required to hold the seal. NEVER use the service cover to push the filter into place! Using the cover to push the filter in could cause damage to the housing or cover fasteners and will void the warranty.

If the service cover contacts the filter before it is fully in place, remove the cover and push the filter (by hand) further into the air cleaner and try again. The cover should go on with no extra force.

Once the filter is in place, secure the service cover.

1 Measure Restriction

Measure the restriction of the air cleaner with a Donaldson filter service indicator, service gauge, or a water manometer via the restriction tap provided on the air cleaner or the transfer pipe. Replace the filter only when the restriction level has reached the maximum recommended by the engine or equipment manufacturer.

2 Check Vacuator™ Valve

On dust cups with Vacuator Valve, dust cup service is minimal; just check the Vacuator Valve to see that it is not inverted, damaged or plugged. If it is damaged, replace it immediately.

3 Check Tubes for Plugging

When the dust cup is removed, check the tubes. Generally, Donaclone tubes are self-cleaning and need no service. Under rare circumstances, however, plugging can occur. Visual inspection is adequate. If the tubes carry light dust, remove it with a stiff brush.

Cleaning Note: Never clean Donaclone tubes with compressed air unless both the primary and safety filters are installed in the air cleaner. Do not steam-clean Donaclone tubes.

4 Change the Filter

When restriction indicates that filter service is required, unfasten or unlatch the service cover. Because the filter fits tightly over the outlet tube to create the critical seal, there will be some initial resistance, similar to breaking the seal on a jar. Grasp the filter service handle and pull the filter out, gently moving the filter back and forth to break the seal.

Avoid knocking the filter against the housing during removal. If the new filter is not to be installed immediately, be sure to cover the seal tube with a cloth or the housing cover so that dirt is not ingested.

NEVER use the service cover to push the filter into place! Using the cover to push the filter in could cause damage to the housing, cover fasteners and will void the warranty.Caution

Heavy Dust Conditions

Engine Air Cleaners, Accessories & Service Parts 111

STG Donaclone™ Air Cleaner

STG Donaclone: Field Proven and Reliable Heavy-Duty Workhorse for Construction & Off-Highway Applications

That Donaldson's STG Donaclone™ is arguably the most commonly used air cleaner, on the widest variety of heavy-duty equipment in the world, is a testament to its reliability and durability. With its two-stage air cleaning, heavy-duty construction, and variety of configurations, the STG works well in many heavy-duty applications like scrapers, crawlers, dumpers and haul trucks.

Powerful Two-Stage FiltrationThe first stage of this powerful air cleaner consists of a cluster of our exclusive, patented Donaclone™ tubes. They spin the incoming air to create a centrifugal force that separates up to 95% of the dust and dirt in the airstream. Donaclone tubes have no moving parts – so there is nothing to break down or maintain. They function properly whenever the engine is running.

This pre-cleaned dust is collected in a dust cup on the bottom of the air cleaner housing.

The second stage of filtration is the primary filter, a cylindrical-shaped unit of specially-developed pleated filter media, designed to trap and stop dust particles, both large and small. The result is air to your engine that is up to 99.9% contaminant free!

If you're replacing a worn out air cleaner, be sure to check ductwork, clamps, and other intake system parts that may also need replacing.

STG air cleaners feature a corrosion-resistant, chemical-resistant polymer coating. This black coating isn't paint, rather it's a pigmented polyester that provides a long-lived, hard protective finish.

A safety filter, which fits inside the primary filter, is standard on all models for protection during primary filter changeout.Physical orientation does not affect the proper functioning of either cleaning stage!

The STG operates well mounted horizontally or vertically. (Note that if mounting horizontally, the Vacuator™ Valve option on the dust cup is necessary.)

Mounting: Sturdy mounting brackets are attached to the top section of the STG; you will also need to order one separate mounting band for the lower body.

This STG Donaclone, mounted on a large mining machine, is protecting the engine from harmful dirt in this severely dusty environment.

Heav

y Du

st C

ondi

tions

112 Engine Air Cleaners, Accessories & Service Parts

STG Donaclone™ Air Cleaner

Versatile STG Provides Airflow to 50 m³/min. Choose Peripheral or Tubular Inlet, Horizontal or Vertical Mount

Applications• Allows 11 to 50 m³/min. airflow

throughput per air cleaner• Horizontal or vertical installation• Off-road, high dust conditions

Air Cleaner Features• Very reliable! Only one critical filter seal!• Airflow throughput can be doubled by

using two air cleaners• Two body styles (peripheral inlet

and tubular inlet) to accommodate location and ducting

• Optional inlet shroud available for peripheral style

• When the air cleaner is mounted directly on the engine and there is clearance around it for airflow, choose the peripheral inlet style (see photo on right)

• When the air cleaner is mounted above the cab or somewhere far from the engine to get above the dust cloud, choose the tubular inlet style, which will accept ducting into the inlet

• Built-in Donaclone pre-cleaning tubes separate up to 95% of incoming dust to dust cup before it reaches the filter, resulting in more thorough cleaning and fewer filter changes!

• Choose the dust cup best suited to your maintenance practices: (1) the quick-release style for easy, manual emptying, or (2) a dust cup with a Donaldson Vacuator Valve that expels the dust automatically

• All models include a fitting for a filter service indicator

Filter Features• Replacement main filter choices:

Standard life filters (for scheduled maintenance) and Donaldson Endurance extended service high efficiency filters

• Safety filter on all models

Choose between two STG body styles (tubular or peripheral), depending on the mounting location of the air cleaner and its ducting. The peripheral inlet style is shown here.

How the Two-Stage STG Donaclone WorksAir is drawn in through the perforations in the lower part of the unit and forced down through a bank of Donaclone tubes.

The Donaclone tubes spin the air so that centrifugal force causes the heavier dust particles to separate from the airstream.

While these particles fall into the dust cup at the bottom, the partially cleaned air is directed upward, into the primary filter in the upper portion of the unit.

The specially-developed pleated media in the primary filter stops up to 99.9% of the remaining dust, allowing clean air to pass to the engine.

Optional Inlet Shroud

Main Filter Housing

Perforated Air Inlet

Pre-Cleaning Section contains a cluster of Donaclone tubes

Dust Cup

Outlet to Engine

Mounting Bracket

Access Cover for Filter Service

Heavy Dust Conditions

Engine Air Cleaners, Accessories & Service Parts 113

STG Donaclone™ Air Cleaner

With Peripheral Inlet With Tubular Inlet

STG Specifications

Heav

y Du

st C

ondi

tions

114 Engine Air Cleaners, Accessories & Service Parts

STG Donaclone™ Air Cleaner

STG Donaclone™ with Peripheral Inlet - Service Parts

NOTES:2 = Two required for proper installation3 = Shipped with air cleaner initially9 = Gasket Kit includes all gaskets listed

ES = Extended Service HE = High EfficiencySM=Scheduled Maintenance

Mounting Bandattached to housing

Safety Filter

Primary FilterSafety Signal® X004816

Gasket Washer P105740

Wing NutP109062

Cover Gasket

GasketBody or Cup

Peripheral Style Bodyshown with optional inlet shroud

GasketBody or Cup

Alternate style Dust Cup for Horizontal Mount

Quick Release Dust Cup

Alternate style Dust Cup for Vertical Mount

Body Clamp

Cup Clamp

Dust Cup

NOTE: If you order one of these alternate style dust cups, be sure to also order the Vacuator™ Valve P112803

Spring Clip & Pin Repair Kit X005555Use it to repair the P017617 latch assembly

Cover

G140076 body, lower ....................................... P102256clamp, cup ........................................ P100866cover latch assembly ..................... P017617dust cup ............................................ P100860 .....3filter, primary - SM .......................... P181041filter, primary - ES & HE .................. P185041filter, primary .................................... P182041 ....3filter, safety ...................................... P119370gasket, body or cup ........................ P017335gasket, cover ................................... P016972gasket kit ......................................... X003538 ....9gasket washer ................................. P105740inlet shroud (optional) .................... P102870mounting band ................................. H000350 ....2 safety signal indicator .................... X004816spring clip & pin .............................. X005555wing nut ............................................ P109062

G160077 body, lower ....................................... P115023clamp, body ...................................... P100780clamp, cup ........................................ P100789cover ................................................. P109153cover latch assembly ..................... P017617dust cup ............................................ P100794 .....3dust cup, quick release ................. P107377dust cup, vac valve, horz .............. P103530dust cup, vac valve, vert ............... P104973filter, primary - SM .......................... P181039filter, primary - ES & HE .................. P185039filter, primary .................................... P182039 ....3filter, safety ...................................... P114931gasket, body or cup ........................ P017336 gasket, cover ................................... P017367 gasket kit ......................................... X003539 ....9gasket washer ................................. P105740inlet shroud (optional) .................... P101759 mounting band ................................. H000351 ....2safety signal indicator .................... X004816spring clip & pin .............................. X005555 wing nut ............................................ P109062

G161006 clamp, body ...................................... P100780clamp, cup ........................................ P100789dust cup ............................................ P100794 .....3dust cup, quick release ................. P107377dust cup, vac valve, horz .............. P103530dust cup, vac valve, vert ............... P104973filter, primary - SM .......................... P181042filter, primary - ES & HE .................. P185042filter, primary .................................... P182042 ....3filter, safety ...................................... P128408gasket, body or cup ........................ P017336 gasket, cover ................................... P017367 gasket kit ......................................... X003539 ....9gasket washer ................................. P105740inlet shroud (optional) .................... P101759 mounting band ................................. H000351 ....2safety signal indicator .................... X004816wing nut ............................................ P109062

Heavy Dust Conditions

Engine Air Cleaners, Accessories & Service Parts 115

STG Donaclone™ Air Cleaner

STG Donaclone™ with Tubular Inlet - Service Parts

NOTES: 2 = Two required for proper installation 3 = Shipped with air cleaner initially 9 = Gasket Kit includes all gaskets listed

ES = Extended Service HE = High EfficiencySM=Scheduled Maintenance

Mounting Bandattached to housing

Safety Filter

Primary Filter

Safety Signal® X004816

Gasket Washer P105740

Wing NutP109062

Cover Gasket

Cover

Gasket(Body or Cup)

Alternate style Dust Cup for Horizontal Mount

Quick Release Dust Cup

Alternate style Dust Cup for Vertical Mount

Body Clamp

Dust Cup

Tubular Inlet Style Body

GasketBody or Cup

NOTE: If you order one of these alternate style dust cups, be sure to also order the Vacuator™ Valve P112803

Cup Clamp

G120332body, lower ....................................... P110875dust cup, quick release ................. P107375filter, primary - SM .......................... P181044filter, primary - ES & HE .................. P185044filter, primary .................................... P182044 ....3filter, safety ...................................... P119371gasket, body or cup ........................ P017804gasket, cover ................................... P017365gasket washer ................................. P105740mounting band ................................. H000349 .....2safety signal indicator .................... X004816spring clip & pin .............................. X005555wing nut

G140445air inlet hood .................................... H000606lower body........................................ P114100cover latch assembly ..................... P017617dust cup ............................................ P100860 .....3dust cup, quick release ................. P107377dust cup, vac valve, horz .............. P103746dust cup, vac valve, vert ............... P105016filter, primary - SM .......................... P181041filter, primary - ES & HE .................. P185041filter, primary .................................... P182041 ....3filter, safety ...................................... P119370gasket, body or cup ........................ P017335gasket, cover ................................... P016972gasket kit ......................................... X003538 ....9gasket washer ................................. P105740mounting band ................................. H000350 .....2safety signal indicator .................... X004816spring clip & pin .............................. X005555wing nut ............................................ P109062

G160445cover ................................................. P109153cover latch assembly ..................... P017617dust cup ............................................ P100794 .....3dust cup, quick release ................. P107377dust cup, vac valve, horz .............. P103530dust cup, vac valve, vert ............... P104973filter, primary - SM .......................... P181039filter, primary - ES & HE .................. P185039filter, primary .................................... P182039 ....3filter, safety ...................................... P114931gasket, body or cup ........................ P017336gasket, cover ................................... P017367gasket kit ......................................... X003539 ....9gasket washer ................................. P105740mounting band ................................. H000351 .....2safety signal indicator .................... X004816spring clip & pin .............................. X005555wing nut ............................................ P109062

G161020 dust cup ............................................ P100794 .....3dust cup, quick release ................. P107377dust cup, vac valve, horz .............. P103530dust cup, vac valve, vert ............... P104973filter, primary - SM .......................... P181042filter, primary - ES & HE .................. P185042filter, primary .................................... P182042 ....3filter, safety ...................................... P128408gasket, body or cup ........................ P017336gasket, cover ................................... P017367gasket kit ......................................... X003539 ....9gasket washer ................................. P105740mounting band ................................. H000351 .....2safety signal indicator .................... X004816wing nut ............................................ P109062

Heavy Dust Conditions

Engine Air Cleaners, Accessories & Service Parts 117

STG Donaclone™ Service Instructions

Check Tubes for Plugging3 When the dust cup is removed, check the tubes. Generally, Donaclone™ and Strata™ tubes are self-cleaning and need no service. Under special circumstances, however, plugging can begin. Visual inspection is adequate. If the tubes carry light dust, remove it with a stiff brush. If heavy plugging with fibrous material is evident, remove the Strata™ or Donaclone™ section and clean it with compressed air or water no hotter than 72°C. Cleaning Note: Never clean Dona-clone™ tubes with compressed air un-less both the primary and safety filters are installed in the air cleaner.

Do not steam-clean Donaclone™ or Strata™ tubes.

Measure Restriction1 Measure the restriction of the air cleaner with a Donaldson filter service indicator, service gauge, or a water manometer via the restriction tap pro-vided on the air cleaner or the transfer pipe. Replace the filter only when the re-striction level has reached the maximum recom-mended by the engine or equipment manufacturer.

Empty the Dust Cup 2 The dust cup should be dumped when 2/3 full. (Frequency of dust cup service varies with dust severity.) When reinstalling dust cup, be sure it

seals 360° around the air cleaner body. On dust cups with Vacuator™ Valve, dust cup service is minimal; just check the Vacuator™ Valve to see that it is not inverted, damaged or plugged. If it is damaged, replace it immediately.

Vacuator™ Valve

Change the Filter4 When restriction indicates that filter service is required, loosen the wing nut and remove the primary filter. If the new filter is not to be installed immediately, be sure to the cover the inlet with a cloth or the housing cover so that dirt is not ingested.

Before installing the new filter, inspect it for shipping damage and gasket integrity. If there is damage, DO NOT install it!

If the wing nut is held in place on the used filter with a C clip, remove it and reinstall on the new filter. Carefully install the new filter and the wing nut. Reset the filter service indicator to green.

Check System5 Inspect and tighten all air clean-er system connections. If there are holes or damage, replace immediate-ly. Inspect all gaskets for worn spots or damage. Annual replacement of air cleaner gaskets is recommended.

While we know printed product information will not disappear

anytime soon, more and more people are choosing to use

our on-line literature informational tools as a product

resource. Not only is it the most current information

and it's available 24/7!

On-Line Product InfoMore Currentis

Than Printed Materials!

http://www.emea.donaldson.com/en/engine/support/datalibrary/index.html

Air Intake Accessories Donaldson

... help you solve problems and maintain your system

NEW

IMPROVED

Section Index

Clamps, Worm-Drive Hose & T-Bolt . . . . . . . . 120Clamps, SealClamps™ . . . . . . . . . . . . . . . . . . . . 121Drop Down Tube Extension (Dust Dumpa) . . . 122Exhaust Ejectors . . . . . . . . . . . . . . . . . . . . . . . . . 124In-Line Check Valve . . . . . . . . . . . . . . . . . . . . . . 126In-Line Separators . . . . . . . . . . . . . . . . . . . . . . . 127Moisture Skimmer & Eliminator . . . . . . . . . . . . 128Mounting Bands, Metal . . . . . . . . . . . . . . . . . . . 129Pre-Cleaners, DonaSpin™ . . . . . . . . . . . . . . . . 130Pre-Cleaners, Full-View. . . . . . . . . . . . . . . . . . . 131Pre-Cleaners, TopSpin™ . . . . . . . . . . . . . . . . . . 132Rain Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134Restriction Indicators. . . . . . . . . . . . . . . . . . . . . 135Rubber Elbows, Humps & Reducers . . . . . . . . 137Silicone Charge Air Connectors. . . . . . . . . . . . 140Vacuator™ Valves. . . . . . . . . . . . . . . . . . . . . . . . 141

When you need to, use...

Mount or install an air cleaner:- Mounting Bands

Solve air intake water problems:- In-line Moisture Skimmer- In-line Moisture Separator- Stack Top Moisture Eliminator

Pre-clean or protect air inlet from debris:- Rain Caps- TopSpin™ Pre-Cleaner- Full-View Pre-Cleaner- Donaspin™ Pre-Cleaner- In-line separator

Know when to service a filter:- Restriction Indicators

Aspirate (or scavenge) an intake system:- Donaspin™ Pre-Cleaner- Exhaust Ejectors- Ejector Check Valve

Improve dust evacuation from Vacuator™ Valves:- Drop Down Tube Extension

Connect intake components:- Rubber Elbows and Connectors- Clamps- Rubber and Silicone Hump/Reducers- Charge Air Connectors

Accessories

Engine Air Cleaners, Accessories & Service Parts 119

Acce

ssor

ies

120 Engine Air Cleaners, Accessories & Service Parts

Clamps

Initial torque on lined hose clamp should be 4.6 Nm.If retorquing is required, limit to 2.3 Nm.

• Versatile clamps for wide size range of hose connections.• Made of strong, durable, noncorrosive stainless steel.• Inside of clamp is lined so that hose doesn’t bulge through clamp holes.• Narrow band enables easy installation in confined areas.

Recommended applicationup to 4.6 Nm torqueDonaldson lined hose clamps seal silicone and other soft hoses with-out damage. The inner liner extends under the perforations to protect the hose and prevents extrusions through the worm-gear perforations.

Recommended applicationup to 10.4 Nm torqueDonaldson Constant Torque lined clamps are the best choice for systems where clamps cannot be retightened and have difficult access. Perfect for applications requiring higher torque, large diameters, temperature extremes, or where expansions and contrac-tions within the system are com-mon. This clamp is a good choice for critical coolant and charge-air connections.

Recommended applicationup to 17.3 Nm torqueThis extra heavy-duty clamp ensures total protection against leakage.....eliminates the need for double clamping.

T-Bolt Clamps

Lined Hose Clamps Part Number Size mm P532919 14-21 P532920 17-24 P532921 21-27 P532923 21-38 P532924 21-44 P532922 29-32 P115200 40-62 P115201 52-76 P143422 71-95 P115202 84-108 P115203 109-133

Constant Torque Clamps Part Number Size mm P532925 57-79 P532926 70-92 P532927 83-105 P532928 95-117 P532929 108-130

High Torque Clamps Part Number Size mm P115204 108-130 P115205 133-156 P115206 159-181 P115207 184-206 P115208 210-232 P115209 260-286

T-Bolt Clamps

Part Number Nominal I.D. Size mm

P148337 51 57-64 P148338 57 63-70 P148339 64 71-78 P148340 70 78-85 P148341 76 84-91 P148342 89 98-104 P148343 102 109-116 P148344 114 122-129 P148345 127 135-142 P148346 140 151-158 P148347 152 162-169 P148348 178 187-198 P148349 203 216-226 P148350 254 267-277

Worm-Drive Hose Clamps

or 32 mm min.

or 6 mm min.

Accessories

Engine Air Cleaners, Accessories & Service Parts 121

Clamps

SealClamps™

Preformed & Flat Styles

Used to seal muffler inlets,outlets, elbow joints, flex pipes,and other system connections.Also minimizes noise andexhaust gas leaks.

SealClamps are easy to install!Theres no need to weld ordisconnect your exhaust system.

When installed, the wide bandconforms to the shape of straightor flex pipe, and seals withoutdistorting the pipe.

• For overlapping I.D. to O.D. slotted joints and flex tube.• Nuts and bolts fit both 9/16" and 14mm wrenches.• Reduces noise and exhaust leaks.• Installs easily – no disconnecting or welding necessary.• Available in aluminized and stainless steels.• Stainless models have improved corrosion resistance and high temperature strength compared to aluminized.

• Full 360º preformed• No flex pipe pinching• Available in stainless and aluminized

Stepped Preformed SealClamp™

Flat Band SealClamp™

Preformed SealClamp™

Stepped Preformed SealClamps Stainless Aluminized Pipe mm

X007829 X007832 64 X007830 X007833 76 X007831 X007834 89 X007784 X007824 102 X007785 X007805 127

Flat Band SealClamps Stainless Aluminized Pipe mm

X004536 51 X004537 57 X004476 64 X004538 70 X004478 X005921 76 X004480 X006204 89 X004482 X006203 102 X004962 114 X004484 X006202 127 X004539 152

Preformed SealClamps Stainless Pipe mm

X005265 64 X005921 76 X005164 89 X007057 152

Acce

ssor

ies

122 Engine Air Cleaners, Accessories & Service Parts

Drop Down Tube Extension(Dust Dumpa)

Replacement to Your Existing Dust Cup Assembly NEW

Part No. X006562(includes dust cup seal)

Application• Donaldson SSG Air Cleaners • Donaldson PowerCore PSD Air

Cleaners (10" and 12" models)

How It Works When installed on the dust cups on the lower assembly, the rubber connector vibrates during normal vehicle operation and gravity expels the pre-cleaned dust.

Features• Improves dust evacuation from the

air cleaner

• Clear tube allows for visual inspection of dust collection

• Improves safety of the air cleaner inspection process by eliminating the need for ladders or elevated platforms for daily inspections

• Allows operators to perform walk around inspections

• Keeps operators and maintenance personnel away from the nuisance dust normally encountered during air cleaner servicing operations.

• Improves vehicle up time by minimizing pre/post –shift air cleaner inspections, thus facilitating increased air cleaner service intervals.

• Reduces air cleaner inspection time

• Ships fully assembled

• Proper conversion requires drop down tube for every dust cup

Part No. X006561

572.822.55

68.12.68

322.312.69

420.116.54

ID76.2

3.00

420.116.54

68.12.68

Part No. X006562

Part No. X006561

Accessories

Engine Air Cleaners, Accessories & Service Parts 123

Drop Down Tube Extension(Dust Dumpa)

Available for SSG Air Cleaners

Existing S Series Air Cleaner Dust Cup Styles

For Conversion Order Kit X006562

For Conversion Order Kit X006561

Quick Release Dust Cup Dust Cup - Original Dust Cup - Newer Design

For Conversion Order Kit X006561

Available for PowerCore® Air Cleaners (PSD08 - 09 - 10 & 12)

Also works on all other Air Cleaners with 76 mm drop tube

Acce

ssor

ies

124 Engine Air Cleaners, Accessories & Service Parts

Exhaust Ejectors

Expanded I.D. End Style

Standard Style

Compact Style

A Donaldson exhaust ejector removes dirt and debris from the air intake pre-cleaner through a scavenge hose that is routed out through the exhaust flow of your equipment.

It mounts as a stack at the end of exhaust system; stack caps or extension tubes may be added. There are three styles available – expanded, standard, compact – depending on the space and design of your equipment. Ejectors require no service and have no moving parts. A Donaldson T-Bolt Clamp, as show on page 120, is recommanded for installation.

All ejectors are constructed of heavy-gauge, aluminised steel. Select the appropriate ejector by the intake airflow (m³/min.) of your engine.

The Donaspin™ pre-cleaner uses a spinning motion of the airstream to force dirt and debris to the outside wall of the pre-cleaner body. The dirt and debris are forced to the bottom of the pre-cleaner and expelled by the secondary airflow developed by the ejector.

Donaspin™ Pre-Cleaner

Intake Air

Exhaust Air

Silicone Hose Scavenge Line

Cleaned Air

Ejector

Expanded I.D. End Style• Simplifies installation - requires less parts to install• No need for separate connector!• Fits over most standard muffler outlet tubes• Adds only 1000 - 2000 Pa to exhaust backpressure

Standard Style• Can be used with any pre-cleaner style• Adds only 1000 - 2000 Pa to exhaust backpressure

Compact Style• Used primarily on agricultural equipment• Adds 2500 - 3800 Pa to exhaust backpressure

Accessories

Engine Air Cleaners, Accessories & Service Parts 125

Exhaust Ejectors

EXPANDED STYLE INSTALLATION

Muffler OutletEnd

Ejector

MaxGrip™ ClampSTANDARD OR COMPACT INSTALLATION

Ejector

MaxGrip™ Clamp

Muffler OutletEnd

O.D. Connector

MaxGrip™ Clamp

Expanded Inlet End Style Ejectors

Part Intake Inlet ID Scavenge Tube ID Length Exhaust 3-ply silicone Lined Number m³/min. mm mm mm m³/min. scavenge hose* Hose clamp min max

H002129 14 - 20 131 38 749 36 51 P171378 P115200 H002132 29,5 - 42 157 51 826 74 105 P171381 P115200

Standard Style Ejectors

Part Intake Inlet ID Scavenge Tube ID Length Exhaust 3-ply silicone Lined Number m³/min. mm mm mm m³/min. scavenge hose* Hose clamp min max

H001032 7 - 10 77 38 445 18 25 P171378 P115200 H001033 9 - 12,5 102 38 610 22 31 P171378 P115200 H001034 11 - 15 102 38 610 27,5 39 P171378 P115200 H001035 14 - 20 128 38 749 36 51 P171378 P115200 H001039 36 - 51,5 153 51 826 92 130 P171381 P115200

Compact Style Ejectors

Part Intake Inlet ID Scavenge Tube ID Length Exhaust 3-ply silicone Lined Number m³/min. mm mm mm m³/min. scavenge hose* Hose clamp min max

H001282* 1 - 2 51 32 178 3 4 P171376 P532924 H001277* 2,5 - 3,5 57,5 32 202 6 9 P171376 P532924 H001283* 3 - 4,5 64 32 226 8 11 P171376 P532924 H001278* 5 - 6 70 32 248 12 15 P171376 P532924 H001280* 6 - 9,5 89 32 318 16 24 P171376 P532924 H001279* 8,5 - 11 77 32 274 21,5 28 P171376 P532924 H001281* 10,5 - 14 102 32 365 26,5 34 P171376 P532924 H001284* 13 - 17 102 32 365 32 42,5 P171376 P532924

* Do not use in fibrous environment, e.g. Combine Harvestors

Acce

ssor

ies

126 Engine Air Cleaners, Accessories & Service Parts

In-Line Check Valve

Installation Instructions

For proper function of the Valve the INDEX needs to be • installed upwardsInstall inline check valve as close as possible to the air • cleanerTemperature resistance of 200°C• Different connection diameters: 32 - 38 - 50 mm•

Scavenge Flow Direction

Check Valve Assy Inlet Diameter Outlet Diameter

P786337 32 32 P786339 50 32 P786338 38 32 P786341 32 38 P786342 50 38 P786340 38 38 P786345 32 50 P786343 50 50 P786344 38 50

Accessories

Engine Air Cleaners, Accessories & Service Parts 127

In-Line Separators

Two-stage Cleaning for Unexpected Dust/Moisture Conditions

When your truck is being used inheavier-than-anticipated dust ormoisture conditions, you may nothave to replace the entire air cleaner.The problem may be solved byadding a Donaldson In-Line Separator.

Installing this unit on your one-stagesystem creates a two-stage air filtration system. This enables an over-highway vehicle, which usually sees only light-dust, to be easily andeconomically adapted to off-road conditions, where medium- to heavy-dust is encountered.

ApplicationsVertical model: On/off road, mounted on inlet tubing or cowl mounted directly to air cleaner- Compatible with engine airflows of 14 to 43 m³/min.Horizontal model: On/off road, typically mounted under hood- Compatible with engine airflows of 3 to 40 m³/min.

Features• 80% water removal efficiency• 70% dust removal efficiency

Horizontal model, for airflow of 3 to 40 m³/min.Mounts underhood.

Vertical model, for airflow of 14 to 43 m³/min.Mounts on stack top.

Vacuator™ ValveP158914

Diameter Length Part Airflow Inlet Outlet (B) (C) (D) Number Range mm mm mm mm mm

Horizontal Style

H001474 (1) 3 - 11 102 OD (2) 102 OD 140 292 182 H000875 14 - 28 152 ID (3) 152 ID 217 438 294 H001906 20 - 40 178 ID 178 ID 244 432 305

Vertical Style

H000878 14 - 31 152 ID 152 ID 217 438 198 H000886 21 - 31 178 ID 178 ID 217 438 198 H001220 26 - 43 203 OD 203 OD 244 432 116

(1) Lightweight aluminium construction (2) OD = Outer Diameter (3) ID = Inner Diameter

How It Works1 When moisture - and/or dust-filled air - enters at one end, the

built-in, stationary vanes cause the air to spin.2 This spin creates centrifugal force, which pushes all moisture and

dust to the outside wall where it separates from the air.3 Moisture and dust are thrown into the Vacuator Valve tubing, then

automatically released by the Vacuator Valve.4 Clean air (acceptable for maximum filter life and engine

performance) passes to the air cleaner.

1

2

3

4

1

2

3

4

Acce

ssor

ies

128 Engine Air Cleaners, Accessories & Service Parts

Moisture Skimmer & Eliminator

Horizontal, In Line Moisture Skimmer Removes Water

Moisture Skimmer

Part Flow Inner Dia. Length Tube Stops Number m³/min (A) (B) (C) (D) mm mm mm mm

X005822 17-28 152 152 32 35 X005900 23 178 152 32 35 X005901* 23 178 152 32 35 * Angled Spout

Applications• Allows 17 to 34 m³/min. airflow.• Horizontal mount in engine air intake ducting.

Features• Removes over 80% of water before it can reach and damage the filter.• No service needed!• Made of durable rubber.• Collected water is automatically released by Vacuator™ Valve.• Adds little or no restriction to airflow.• Common inlet sizes fit most installations.

Mounting Position

Stack-Top Moisture Eliminator Prevents Water Provers

• For cabover trucks, on/off road, mounted on top of 7" (178mm) O.D. intake stack.• For airflow range of 17 to 34 m³/min.• Over 80% water removal efficiency.• Includes clamp for installation.

How They Work(1) Moisture-filled air enters the moisture eliminator cap.(2) Built-in, stationary vanes cause the air to spin.(3) Moisture is forced to the outside wall, where it separates from the air and collects.(4) Water drains out through the drain hole.(5) As a result, drier air (acceptable for maximum filter life and engine performance) passes to the air cleaner.

X003691

1

2

34

5

Accessories

Engine Air Cleaners, Accessories & Service Parts 129

Metal Mounting Bands

Most of our Air Cleaners with metal housings require two mounting bands.

• Durable, corrosion resistant, steel construction.• Fully engineered and tested to resist the adverse effects of vibration.• Mounting band feet are designed to ensure maximum torque pressure, continuously.• Gauge of steel increases as diameter of mounting band increases.• Bright stainless models available.• Bolt and nut included with mounting band.• Used on all Axial Seal Air Cleaners and FRG Radial Seal Air Cleaners.

Many sizes Designed to Fit all Donaldson Air Cleaners

Part Number Dimensions (mm) A B C D E F

P004055 111 68 82,5 19 9,0 90 P002348 134 81 82 22 9,0 90 P002351 153 91 83 26 9,0 90 P007191 165 99 95 22 11 X 16 90 P004906 178 105 111 22 10 X 13 90 E500206 203 114 108 25 12 X 17 90 P004307 203 114 108 25 9 90 P004073 229 130 114 32 12 90 P004076 259 146 127 32 12 90 H770025* 259 146 127 32 12 90 P004079 279 156 127 32 11 90 H000349 300 175 152 38 11 90 P013722 330 184 152 38 10 90 H770065 330 206 203 38 12 90 H770059 345 191,5 142 38 10 90 H000350 356 206 203 38 12 90 P016845 381 203 203 38 12 90 H000351 407 231 254 38 12 90 H770037 457 234 400 50 14 105 H770068 546 279 490 48 14 105

* With cage nut

Acce

ssor

ies

130 Engine Air Cleaners, Accessories & Service Parts

Donaspin™ Pre-Cleaners

The Donaspin Pre-Cleaner extends the life your air filter by removing up to 90% of the dirt and contaminant before it reaches the filter and ejecting it automatically via the exhaust. (See page 124-125 for Exhaust Ejectors.)

Donaspin is designed especially for equipment operating in very heavy dust/debris environments such as garbage trucks, agricultural vehicles and mining equipment.

Application

• For engine airflows of 9-22 m³/min.

• Recommended mounting: on top of the air inlet stack

Features

• Built-in louvers spin air to separate up to 90% of incoming dirt and debris from the air intake system

• Works as part of a scavenged flow system to continuously expel pre-cleaned contaminants through the exhaust flow

• Durable, corrosion-resistant steel construction

• High efficiency with low restriction

• No maintenance! Self-cleaning! No moving parts!

• Mounting clamp is included

How It Works

The Donaspin installed on this combine removes most of the incoming dirt, then directs the contaminant out of the system with the exhaust gases.

To create a scavenged flow system, combine the Donaspin with a Donaldson exhaust ejector and ejector check valve.

Extends Filter Life in Extremely Heavy Dust Conditions

Part Number Rated Airflow Dimensions

(m³/min) @ 12,5 A B (ID) C D E F mbar added mm mm mm mm mm mm

H001212 9 203 76 304 55 305 32 H001307 11 203 96 292 42 305 32 H001215 13 203 115 284 28 305 32 H001308 15 203 128 283 33 305 32 H001375 22 229 154 373 34 330 32

Accessories

Engine Air Cleaners, Accessories & Service Parts 131

Full-View Pre-Cleaners

Extends Filter Life on Agricultural & Construction Equipment

Donaldson has a new Pre-Cleaner calledTopSpin™. Before you consider replacingyour Full-View Pre-Cleaner with anotherone, check out the TopSpin models onpage 132 and 133.

Cover

Dust Cup:Transparent

Plastic

Base:OpaquePlastic

Full-View TopSpin™ Pre-Cleaners Pre-Cleaners

H000820 H002425 H000821 H002426 H000822 H002394 H000823 H002427 H001250 H002435 H001251 H002436 H001249 H002437 H001823 H002434 H002043 H002433 H002044 H002432 H002045 H002431 H002223 H002438 H002224 H002439

Full-View Replacement Parts Max Airflow Inlet OD PreCleaner A B C D Cover Bowl Clamp (m³/min.) mm mm mm mm

H002041 P020116 P020115 P532924 2 35 142 142,5 44 H002042 P020116 P020115 P115200 2 44 142 142,5 44 H002040 P020116 P020115 P115200 2,5 51 142 142,5 44 H001250 P020648 P020227 P115201 4 57 186 157 44 H001251 P020648 P020227 P115201 4 64 186 157 44 H001249 P020648 P020227 P143422 5 77 186 157 44 H000820 P016548 P016330 P143422 9 77 270 190 47 H000821 P016548 P016330 P115202 9 96 270 188 47 H000822 P016548 P016330 P115202 9,5 102 270 189 47 H000823 P016548 P016330 P115203 10 115 270 188 47 H002043 P020345 P020344 P115203 21 127 306 195 51 H002223 P104691 P158324 - 37 152 412 258 70 H002224 P104691 P158324 - 42,5 178 412 258 70

Features• Recommended mounting: on top of the engine intake stack.• Centrifugal force in bowl separates up to 75% of incoming dust before it enters the engine air intake system.• Low maintenance!• Durable, lightweight, noncorrosive construction.• Full-View plastic bowl lets operator easily see when service is needed.• One-bolt cover retention for service when dirt reaches the level of the arrow, remove top nut and plastic body then empty – no tools required.• Mounting clamp included.

Acce

ssor

ies

132 Engine Air Cleaners, Accessories & Service Parts

TopSpin™ Pre-Cleaners

Extends Filter Life in Extremely Heavy Dust Conditions

Donaldson TopSpin™ will extend primary air filter life, boost system efficiency and extend engine life! We recently upgraded the cover material of the TopSpin Pre-Cleaner to increase impact resistance. Before it was a see-through unit, now it is black.

FeaturesSeparates up to 85% of incoming contaminant per ISO 5011/SAE J726• Greatly extends air filter life• Reduces air filter usage • Lowers cost per operating hour• Automatically ejects mixed debris • Separates more than 99% of 20

micron and above particles

Operates at a lower RPM • Less noise• Longer bearing life• Lower restriction

Self-cleaning/self-scavenging• No maintenance to clean bowl• No exhaust ejector required

Easy installation• Quick installation• One clamp to tighten• No wires or power requirements

Dual mounted bearings• More robust design• Extends bearing life

Lighter Weight• Lighter than competitive pre-

cleaners• Lighter than Donaldson full-view

pre-cleaner

Application• Engine airflows of 2-43 m³/min.• Primarily used in medium to heavy

dust environments• Great for off-road vehicles and

equipment from crawler tractors to farm tractors to skid steer loaders

• Recommended mounting: on top of the air cleaner inlet stack

• Can be mounted horizontally or vertically• Installation instructions, stainless clamp / warranty are included• Operating temperature range: to 82°C

Donaldson TopSpin mounted on a grader. The aerodynamically

designed TopSpin™ is made of a lightweight, durable, non-corroding

material which makes it tolerant to all weather and operating

conditions.

Incoming dirty air

Pre-cleaned air entering the intake system

More than 99% of contaminant 20 micron and larger is expelled

IMPROVED ne life! Wethe TopSpin ce. Before it

Accessories

Engine Air Cleaners, Accessories & Service Parts 133

TopSpin™ Pre-Cleaners

Multiple tests conducted per ISO 5011/SAE J726 and average results are shown in charts below.

TopSpin™ Specifications

Part Outlet Overall Body Operating Number I.D. (C) Height (A) Dia. (B) Flow Range mm mm mm m³/min.

H002434 51,5 146 162 2,5 - 6 H002435 58 146 162 2,5 - 6 H002436 64 146 162 2,5 - 6 H002437 77 146 162 2,5 - 6 H002425 78 238 242 6 - 13 H002426 97 238 242 6 - 13 H002394 103 238 242 6 - 13 H002431 103 287 288 13 - 21 H002427 116 238 242 6 - 13 H002432 116 287 288 13 - 21 H002433 128 287 288 13 - 21 H002438 153 345 397 21 - 42,5 H002439 179 345 397 21 - 42,5

Cross References from Full View to TopSpin™ Pre-Cleaner can be found on page 131.

TopSpin™ Performance Curves

Acce

ssor

ies

134 Engine Air Cleaners, Accessories & Service Parts

Rain Caps

Rain Caps Protect Against Large Debris Ingestion

• Protects engine air intake from rain, snow, birds, and other large contaminants.• Mounts on stack or directly to air cleaner for on-road and off-road equipment.• Two styles in a wide variety of sizes.• Installs easily with one clamp which is included.

Style Part Dimensions (mm) Number A B C

A H770066 45 110 56 B H001377 52 152 86 B H001378 64 152 86 B H001379 77 152 86 B H770010 96 266 132 B H770081 97 200 140 B H770011 102 266 130 B H770012 115 266 126 B H770013 128 266 123 B H770090 154 405 144 B H770089 179 405 144 A H001053 207 405 157 A H770082 254 406 189

StyleA

StyleB

Accessories

Engine Air Cleaners, Accessories & Service Parts 135

Restriction Indicators

Replacing filters based on restriction readings can reduce your maintenance costs significantly. Visual inspection of air filters is not adequate and should not dictate service life. Filters that appear very dirty may still contain a great amount of service life.

Over-servicing and excessive handling of the filter can result in serious consequences: filter damage, improper installation, intake contamination from ambient dust, and/or increased service cost, time and material. In contrast, filter service based on restriction readings can enable you to obtain: the longest life possible from the filter, and the best engine protection.

Restriction Readings, Where & WhenRestriction readings are normally taken at the air cleaner on the clean side of the air filter. If the air cleaner does not have a restriction tap, readings can be taken anywhere in the system between the air cleaner and the engine. To measure restriction of a naturally aspirated diesel engine, the reading is taken at full-governed RPM with no load.

Two methods are used to measure the restriction of turbo-charged engines. The first method is to take the reading with the truck on a dynamometer under full load. This result is actual restriction. A locking step gauge is the second method. This popular method will give actual, on-the-road peak readings.

Maximum Restriction Limits for EnginesMaximum allowable restriction limits are set by the engine man-ufacturers. If your maximum limit is unknown, contact your engine manufacturer for the maximum limits.

Maximum levelsare measured at high idle with no load for naturally aspirated and super-charged diesel engines. Turbo-charged diesel, gasoline and carbureted engines are mea-sured at full load with a wide open throttle.

Choose Restriction Measurement Tools that Best Fit Your ApplicationsDonaldson offers a variety of restriction measuring devices that help you get maximum filter utilization. All measure restriction in inches of water vacuum. All are resistant to vibration, breakage, weather, corrosion, dust and dirt to assure reliable filter restriction readings.

Types of IndicatorsContinuous Reading devises show how much life is left in the filter:• The Informer™ Mechanical Indicators

Go/No-Go restriction readings on heavy-duty vehicles:• ServiSignal™• Electrical Indicator

Electrical Indicator with AMP• Connector

Filter service indicators are very effective when mounted on the outlet tube of the air cleaner, as is The Informer™ above. This gives the operator constant & accurate visibility of filter life.

Air Cleaner Inlet

Service Indicatormounted on clean air outlet

Filter Service Indicators Maximize Filter Life Mounting Options: On air cleaner outlet tube, on intake duct or remote

Air Cleaner Outlet

Acce

ssor

ies

136 Engine Air Cleaners, Accessories & Service Parts

Restriction Indicators

The lnformer™ for Graduated,Continuous ReadingsThe Informer,when mountedon the aircleaner orthe dashboard,providesa continuousreadingwhetherthe engine isrunning oris shut down.Reset buttonis on top.Kit includes fullinstallationinstructions and aP100089 safetyfilter fitting.For remote mounting, order aP105168 flange and aP105622 90° elbow.

ServiSignal™ Mini IndicatorSmall enough to fit just aboutanywhere (only42 mm high), theDonaldsonServiSignal™shows a highlyvisible, brightred flag inthe full-viewwindowwhen restrictionlimit is reached.Resets manuallyvia top buttonafter air cleanerservice.Kit includes 1/8"NPT threaded brass fitting formounting on the aircleaner. For remotemount, also orderP105168 flange. Hoses are notincluded.

Mechanical Indicators

Part Restriction Limits Fitting Number mbar Pa mm H2o

ServiSignal™ Mini Indicators X002250 37 3700 380 1/8"-27 NPT X002251 50 5000 508 1/8"-27 NPT X002252 62 6200 635 1/8"-27 NPT X002254 75 7500 762 1/8"-27 NPT

Informer™ Indicators

X002278 50 5000 508 1/8"-27 NPT X002277 62 6200 635 1/8"-27 NPT X002275 75 7500 762 1/8"-27 NPT

Electrical Indicators

Part Restriction Limits Fitting Number mbar Pa mm H2o

Electrical Indicators

X770037 37 3700 380 1/8"-27 NPT X770050 50 5000 508 1/8"-27 NPT X770052 50 5000 508 M10 X 1 X770061 62 6200 635 M10 X 1 X770062 62 6200 635 1/8"-27 NPT X770075 75 7500 762 1/8"-27 NPT Electrical Indicators with AMP connectors

X770225 64 6400 627 M10 X 1 X770301 54 5400 530 M10 X 1 X770316 54 5400 530 1/8"-27 NPT X770317 64 6400 627 1/8"-27 NPT X770526 75 7500 762 1/8"-27 NPT

Electrical IndicatorsConnects to Light, Buzzer, or Computer

Designed for a variety of on- and off-highway applications. • Should be screwed on the air cleaner nipple by hand.• Operating temperatures of -10°C to +100°C. • When restriction level reaches the maximum recommended limit,•

an electrical signal activates a light, a buzzer, or a computer. The indicator automatically resets itself after the filter is serviced.• 12-24 Volts.• Maximum load: 6 watts (light or buzzer).• Contacts have no polarity. • Switch contacts are normally•

in the open position. If inductive load can occur,•

appropriate protection must be provided.

Quick connectors and light,• buzzer, or computer must be purchased separately.

Accessories

Engine Air Cleaners, Accessories & Service Parts 137

Rubber Elbows, Humps & Reducers

Flexible rubber adapters and elbows have smooth radii and inside surfaces to minimize flow resistance within the air intake system. These rubber products are haevy duty.

Specifications

• EPDM rubber construction for improved heat resistance and low temperature flexibility (to 100°C).• Non corrosive construction resists tears, punctures, and vacuum collapse under severe conditions.• Ideal for light-, medium- and heavy-duty applications.• Elbows ribbed or compounded for extra strength and durability. Rubber adapters help to absorb vibrations and reduce intake noise level.

90° Elbows & Elbow Reducers

90° Elbow Reducers

Part Dimension (mm) Outer Dia Number A B C R mm

P781510 40 45 80 45 46 - 51 P778565 76 60 65 70 71 - 87 P775228 76 70 113 60 82 - 88 P123462 76 89 89 57 89 - 102 P121482 127 102 152 95 114 - 140 P143895 152 127 178 108 140 - 165 P159820 178 127 178 108 140 - 190 P128990 178 140 146 111 156 - 194 P117724 152 140 170 127 152 - 165

90° Elbows

Part Dimension (mm) Outer Dia Number A B R mm

P781509 45 80 51 51 P105529 50 89 51 61 P105530 57 95 57 67 P105531 63 102 64 76 P105532 76 127 83 89 P114318 89 140 102 102 P105533 102 146 105 114 P113733 114 140 89 127 P107844 127 156 115 140 P105534 140 165 121 153 P105535 152 171 127 165 P105536 178 192 141 194 P112605 203 216 165 223 P114314 254 267 216 273

Acce

ssor

ies

138 Engine Air Cleaners, Accessories & Service Parts

Rubber Elbows, Humps & Reducers

45° Elbows & Elbow Reducers

Straight Humps

45° Elbow Reducers

Part Dimension (mm) Outer Dia Number A B C R mm

P133338 152 140 164 124 153 - 165 P133339 153 178 184 135 168 - 194

45° Elbows

Part Dimension (mm) Outer Dia Number A C R mm

P105541 50 102 51 61 P105542 56 105 57 67 P105543 64 110 64 74 P105544 76 140 95 89 P109331 89 127 89 102 P105545 102 140 108 114 P114316 114 129 89 127 P109021 127 143 115 140 P105546 140 159 121 153 P105547 153 165 127 165 P105548 178 203 141 194 P112606 203 203 165 222 P114313 254 241 216 273

Rubber Straight Humps

Part Dimension (mm) Outer Dia Number A B mm

P781511 45 50 51 P105608 76 135 89 P114319 89 134 102 P105609 102 134 115 P114317 114 153 127 P105610 127 153 140 P105611 140 153 153 P105612 153 178 165 P105613 178 178 191 P112608 203 127 216 P111414 254 153 267

Accessories

Engine Air Cleaners, Accessories & Service Parts 139

Rubber Elbows, Humps & Reducers

Hump Reducers

Reducers

Part Dimension (mm) Outer Dia Number A B C mm

P114411 38 26 64 36 - 49 P114412 38 32 64 42 - 49 P104087 51 38 64 49 - 61 P102948 51 45 64 55 - 61 P104088 57 51 64 61 - 68 P104089 64 51 64 62 - 75 P104090 64 58 64 68 - 74

Reducers

Rubber Hump Reducers

Part Dimension (mm) Outer Dia Number A B C mm

P102820 76 64 114 75 - 89 P520883 76 70 89 83 - 89 P520882 89 70 102 80 - 99 P101290 89 76 127 89 - 102 P520884 102 70 102 80 - 111 P101291 102 76 134 89 - 114 P101292 102 89 134 102 - 114 P101293 127 102 153 114 - 140 P101891 140 102 153 114 - 153 P103516 140 127 153 140 - 153 P112611 153 127 153 140 - 165 P101294 153 140 153 153 - 165 P126530 178 140 178 153 - 191 P112610 178 153 153 165 - 191 P136494 178 127 178 140 - 191 P129660 203 140 178 152 - 216 P114315 203 153 153 165 - 216 P112609 203 178 153 191 - 216 P112607 254 203 153 216 - 267

Acce

ssor

ies

140 Engine Air Cleaners, Accessories & Service Parts

Silicone Charge Air Connectors

Isolate Intake Piping Vibration

Our three styles of charge airconnectors are designed to easeconnections in air intake systempiping: they compensate forslight misalignment and isolatevibration between hoseconnections. The siliconeelastomer material resistschemicals, steam, ozone,coolants and aging conditionsnormally found in any engineoperating environment.

All three charge air connectorsare for installation on thepressure side with maximumoperating temperatures up to260°C. They are orangein color to be easily identifiableas tolerant of high temperatures.

4-Ply Bellows

Fiberglass Connector/Sleeve

Hump HoseConnector

Use the illustration as a guide for installing your Silicone Charge Air Connector.

Connectors/Sleeves

Part Inner Dia Outer Dia Length Number mm mm mm

P532946 32 38 914

P532947 38 44 914 P532948 51 57 914 P532949 57 63 914 P532950 64 69 914 P532951 76 82 914 P532952 86 92 89 P532953 86 92 152 P532954 86 92 914 P532956 89 95 89 P532957 89 95 114 P532958 89 95 914 P532959 102 107 914

4-Ply Bellows

Part Inner Dia Outer Dia Length No of Number mm mm mm rings

P535572 89 95 152 3 P532943 102 107 152 0 P535571 102 107 152 2 P532944 102 107 152 3 P532945 102 107 191 3 P535573 102 107 203 3

Hump Hose Connectors

Part Inner Dia Outer Dia Length Number mm mm mm

P532960 66 72 140 P532961 70 78 108 P532962 76 85 111

Accessories

Engine Air Cleaners, Accessories & Service Parts 141

Vacuator™ Valves

Replace Damaged or Missing Vacuator™ Valves Immediately!

The Vacuator™ Valve, standard on the majority of Donaldson air cleaners, is an important part of the functionality of the air cleaner. It is an integral part of the pre-cleaning stage on two-stage air cleaners.

The dust cup, where pre-cleaned dust is collected, is normally under a slight vacuum when the engine is running. The normal engine pulsing of the vacuum causes the Vacuator™ Valve to open and close. This action automatically expels any collected dust and water. The Vacuator Valve also unloads when the engine is stopped.

Application Notes

• For proper operation, the Vacuator™ Valve should be located at the lowest point on the air cleaner or dust cup pointing down.• Never paint the Vacuator Valve. Solvents and chemicals will shorten the usable life.• If the Vacuator Valve is torn, shredded or turned inside out, its durometer may be too soft for the application. Choose a model with a harder durometer (higher number). Conversely, if the Vacuator Valve doesn’t empty itself properly, the durometer may be too hard. Choose one with a softer durometer (lower number.)

P776008

P158914 P522958

P112803P106593

P105220P103198

P149099P525956

The Donaldson Vacuator Valve is made in a variety of sizes and shapes to fit various applications. The Donaldson part number is molded into each part for easy identification

For the longest filter service life, replace damaged or missing Vacuator™ Valves immediately!

If your valve is cracked, torn, remains open or is missing, dust particles that are normally expelled can deposit themselves onto the filter and will shorten air filter service life. Replace it!

Part Diameter Durometer Number

P103198 76 40 P105220 76 60 P106593 76 60 P112803 76 40 P149099 25 60 P158914 51 50 P522958 51 60 P525956 25 60 P775569 * 51 60 P776008 51 60

* 45° Vacuator Valve

Missing?Open? Torn?Cracked?

While we know printed product information will not disappear

anytime soon, more and more people are choosing to use

our on-line literature informational tools as a product

resource. Not only is it the most current information

and it's available 24/7!

On-Line Product InfoMore Currentis

Than Printed Materials!

http://www.emea.donaldson.com/en/engine/support/datalibrary/index.html

Proper air cleaner servicing results in maximum engine protection against the ravages of dust.

Proper servicing can also save you time and money by maximizing filter life and air cleaning efficiency.

Two of the most common problems are:

Over Servicing New filters increase in dust cleaning efficiency as dust builds up on the media. Don’t be fooled by filter appearance! A used filter should look dirty. By using proper filter measurement tools, you will use the full life of the filter at maximum efficiency.

Improper ServicingYour engine is vulnerable to abrasive dustcontaminants during the servicing process. The most common cause of engine damage is improper servicing procedures.

By following the steps listedin this section, you can avoid unnecessaryrisk to the engine.

Section Index

Air Filter Cleaning . . . . . . . . . . . . . . . . . . . . . . . . 144Air Filter Inspection . . . . . . . . . . . . . . . . . . . . . . 145General Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

Check out at the end of each Air Cleaner Section the Service Instructions.

Service is EssentielProper Air Cleaner

Engine Air Cleaners, Accessories & Service Parts 143

Maintenance and Servicing

Mai

nten

ance

and

Ser

vici

ng

144 Engine Air Cleaners, Accessories & Service Parts

Air Filter Cleaning

Some vehicle owners and maintenance supervisors,concerned with lowering their operating costs, clean and reuse their heavy-duty air filter.

Factors to consider before you decide whether cleaning or washing of air filters is appropriate for your vehicle or fleet:

• Heavy-duty air filter manufacturers do not recom- mend any type of cleaning process be used on their products. Donaldson, like other heavy-duty air filter manufacturers, does not warrant the air filter once it has been cleaned.

• Damaged filters should not be cleaned or reused. If the filter is damaged in service, investigate the source of damage and make corrections to avoid future damage.

• Never attempt to clean a safety element. Replace it after three main element services.

• Rather than cleaning or reusing filters, consider upgrading to an extended service filter and service the filter by restriction indicators. Donaldson recommends, when the specified maximum service limits are reached, to follow the proper service procedures and replace the used filter with a new Donaldson filter. Dispose of the used filter in a responsible manner.

Filter dirt holding capacity is reduced 20-40% with each cleaning.

There is a risk of dirt reaching the clean side of the filter while cleaning, plus possible filter damage from high pressure water or compressed air, makes cleaning or washing a gamble. Add the cost of cleaning to the danger of filter damage when determining the risk versus the value of filter cleaning process.

Reuse of cleaned heavy duty filters increases the likelihood of improper air cleaner servicing because ofthe shortened service life. Each time the air intake system is serviced, it is exposed to the possibility of contamination.

Donaldson recommends to service Air Filters by monitoring the airflow restriction levels in the air intake system

Maintenance and Servicing

Engine Air Cleaners, Accessories & Service Parts 145

Air Filter Inspection

What is a Hole and What is a False Alarm?

Donaldson receives filters for inspection each year that customers believe have developed holes. Upon inspection and testing in our labs, most of these suspect filters prove to have no holes or leaks.Most often these filters have areas with low dust buildup where light comes through the media when inspected with a light inside the filter, but in fact the filter functions perfectly.

How do you tell the differencebetween a hole and low dust build-up?

The problem is that normal dust buildup shuts out light completely, while low dust buildup permits light to shine through the media. The contrast is significant and therefore looks like a crack or hole in the media. The contrast between a leak and low dust buildup is not as pronounced, which accounts for mis-identifications.

The deceiving low dust areas appear most often at the fold or at the adhesive beading present on some filters.

The secret to identifying a hole in the filter is to realize that when a hole is present you actually see the bright lamp filament shining through the hole, while low dust buildup is merely a bright area where the media is folded and not covered with dust.

Another basic sign of a hole is dust on the liner or endcap of the clean air side of the filter. If there is no sign of dust on the clean-side liner of the filter you can be quite sure that there is no leak in the filter.

On this photo, it isapparent that the filterhas low dust buildupon the pleats or folds,but is functioningefficiently - no holes,no leaks.

Here, light is comingthrough the adhesivebeaded area as wellas at the folds. Again no holes, no leaks.

As you look at thephoto on the left, youcan see it shows ahole in the media. The other light areas arenot holes, but rathermore low dust areason the adhesivebeading, which is usedfor pleat spacing.

In this last example,there are obviousdust trails on the lineror endcap of theclean air side of thefilter. A dust trailusually indicates aleak.

Mai

nten

ance

and

Ser

vici

ng

146 Engine Air Cleaners, Accessories & Service Parts

General Maintenance & Service Tips

5 Don't Ignore a Worn or Damaged Gasket in the HousingIf your air cleaner has a cover gasket, replace it with anew one. Always check to be sure that no piece of theold gasket remains in thehousing and that the gasket isnot worn. If your filter modelcalls for a new gasket with eachuse, never reuse the old one.

6 Don't Use a Damaged or Bunched FilterNever install a dented or punctured filter because it cannot protect properly againstcontamination. A dent can make a firm seal impossible or can indicate damaged media. A filter with bunched pleats saps engine power and fuel euros.

7 Replace Missing or Damaged PartsCheck to ensure that there is no damage to the air cleaner housing that could cause a leak. Replace any missing or damaged Vacuator Valves and air cleaner fasteners. Never attempt to repair a damaged filter.

8 Never Substitute an Incorrect Filter Model NumberFilters may look almost identical, but even a fraction of a mm difference in size can prevent a good seal or affect airflow. Selecting a filter by size may give you the wrong media area and grade and therefore affect service life and filter efficiency.

1 Don’t Remove Filter for InspectionSuch a check will always do moreharm than good. Ridges of dirt on the gasket sealing surface can drop on the clean filter side when the gasket is released. Stick with the regular maintenance schedule, or, if you service by restriction, believe the gauge or restriction indicator. Get a new indicator if you don’t trust yourcurrent one.

2 Never Rap a Filter to Clean ItRapping hard enough to knock off dust damages the filter and destroys your engine protection. Deeply embedded dirt is never released by tapping. It is always safer to keep operating until you can change to a new filter.

3 Never Judge the Filters Life by looking at it. Measure the Airflow RestrictionA dirty-looking filter may still haveplenty of life left, while carboncontamination may not be visible to the eye. You can’t see the dirt that's embedded deep within the filter paper. Your best bet for lowest filter maintenance costs and best engine protection is to follow a restriction indicator. It's a smart, low-cost investment.

4 Never Leave an Air Cleaner open longer than necessaryYour open air cleaner is a direct entry to the engine! Keep it protected during filter changes. Contaminants smaller than we can see will cause damage to a diesel engine. If the housing is not going to be reassem-bled immediately, cover the opening.The only way to be sure nothing got in, is to make sure nothing can get in!

Engine Air Cleaners, Accessories & Service Parts 147

Service Parts by Air Cleaner Model

EBA A092029 P129472 P141787 P120597 P004073 Production EBA A092040 P140822 P120597 P004073 Cancelled EBA A110029 P772512 Cancelled EBA A130071 P182007 P013722 Cancelled FWA A140003 P181000 P118808 P017335 P018464 H000350 H770013 Cancelled FWA A140033 P181000 P118807 P103198 P017335 P018464 H000350 H770013 Cancelled FWA A140206 P181000 P118807 P103198 P017335 P018464 H000350 H770013 Cancelled FWA A140208 P181000 Cancelled FGA A144800 P016688 Cancelled FGA A144900 P016688 P016996 Cancelled FGA A161500 P782261 P782268 Production FKB B045008 P604457 P603729 P606497 P158914 Production FKB B055006 P609218 P602427 P609219 P158914 Production FKB B065045 P609221 P608599 P608592 P158914 Production ELB B065011 P772552 P007191 H001379 Production ELB B065012 P772552 P770181 P007191 H001379 Production FLB B065018 P772565 P770207 P138403 P007191 Production EPB B070005 P772579 P775300 P778758 P777731 H001379 Production ELB B080009 P772529 P004307 H770010 Production ELB B080010 P772529 P119410 P004307 H770010 Production ELB B080017 P774517 P771363 Cancelled ERB B080018 P770829 P770735 P101870 Cancelled ERB B080019 P770828 P127787 P101870 E500206 H770010 Cancelled FLB B080022 P772556 P119410 P138403 P004307 Production ELB B080024 P774517 P771363 P101870 H001379 Production ELB B080031 P772529 E500206 H770011 Cancelled ELB B080033 P772529 P119410 P101870 P004307 Cancelled ELB B080039 P776146 P776147 P181070 E500206 H770010 Cancelled ELB B080040 P774517 P771363 P101870 H770010 Production FLB B080046 P778702 P775457 P138403 E500206 Production EPB B080067 P772580 P775302 P775305 P777732 H770010 Production XRB B080080 P611190 P611189 P605731 P158914 Production ERB B090010 P182092 P119778 P134945 P101870 P004073 H770012 Cancelled ERB B090019 P182092 P134945 P101870 P004073 H770012 Cancelled ERB B090023 P182092 P119778 P134945 P137368 P101870 P004073 H770012 Cancelled ELB B090047 P777230 P777247 P101870 P004073 H770011 Cancelled SRB B095437 P780522 P780523 P782176 P004073 Production ERB B100035 P182090 P119375 P128443 P128707 P101870 P004076 H770012 Production ERB B100037 P182090 P119375 Cancelled ERB B100041 P117439 P123828 P128443 P101870 P004076 H770012 Cancelled ERB B100044 P182090 P119375 P128443 P128707 P101870 P004076 H770012 Production ERB B100046 P182090 P119375 Cancelled ELB B100057 P772522 P133138 P138403 P004076 H770012 Production FLB B100067 P772530 P133138 P138403 P004076 Production ELB B100068 P772522 P004076 H770012 Production ELB B100071 P772522 P133138 P138403 P004076 H770012 Production ELB B100072 P772527 P123828 P775455 P004076 H770013 Production ELB B100075 P774538 P775005 P138403 P004076 H770012 Production ELB B100078 P774547 P775035 P138403 P004076 H770012 Cancelled ERB B100120 P778214 P777639 P777998 P004076 H770012 Cancelled SRB B100121 P778214 P777639 P777998 P004076 Production ERB2 B100126 P785388 P770685 P784954 P004076 H770012 Production XRB B100127 P611539 P611540 P609942 P158914 Production ERB B110154 P778905 P778906 P783014 P004079 H770013 Cancelled SRB B110155 P778905 P778906 P783014 P004079 Production ERB B120153 P182091 P130772 P130501 H000349 H770013 Cancelled ERB B120190 P182091 P130772 P130501 H000349 H770013 Cancelled ERB B120246 P182091 Cancelled FLB B120260 P772520 P770678 P138403 H000349 Production ELB B120265 P772524 P770678 P138403 H000349 H770013 Production ELB B120268 P772524 H000349 H770013 Production ELB B120290 P772524 P770678 P138403 H000349 H770013 Production STB B120319 P772524 P770678 P138403 H000349 Production ERB B120395 P536315 P529286 P529798 Cancelled XRB B120470 P608116 P608391 P608117 P158914 Production ERB B130010 P777279 P777300 P013722 H770089 Cancelled ERB B130013 P777279 P777414 P777300 P013722 H770089 Cancelled ERB B130028 P781768 P781784 P533226 P013722 H770089 Production SRB B130046 P777409 P777414 P781124 P013722 Production SPB2 B130048 P783543 X770684 P783693 Integrated Production ERB2 B130057 P785610 P783693 P013722 H770089 Production ERB2 B130058 P785610 X770686 P783693 P013722 H770089 Production SPB2 B130060 P783543 X770684 P783693 Integrated Production ERB B140139 P182002 P119373 P770605 P017335 P775455 H000350 H000606 Production EGB B140159 P772523 P776172 P017335 H000350 H000606 Production EGB B140167 P772523 P119373 P776172 P017335 P775455 H000350 H000606 Production EGB B140175 P772521 P776172 P017335 H000350 H000606 Production EGB B140176 P772521 P119373 P776172 P017335 P775455 H000350 H000606 Production EGB B140317 P775026 P776102 P782130 P017335 P770920 H000350 H770089 Production ERB B150025 P777871 P777875 P777861 P016845 H770089 Cancelled

Style Air Cleaner Main Safety Cover Vacuator™ Gasket Wing Mounting Rain Status Model No. Element Element Assembly Valve Nut Assy Band Cap

Service Parts

148 Engine Air Cleaners, Accessories & Service Parts

Service Parts by Air Cleaner Model

ERB B150028 P777871 P777861 P016845 H770089 Cancelled ERB B150030 P777871 P777920 P158914 P016845 H770089 Production ERB2 B150058 P785426 X770687 P784869 P016845 H770089 Production ERB2 B150059 P785426 P784869 P016845 H770089 Production ETB B180002 P182042 P128408 P780042 P109062 H770037 H001053 Production ERB B180011 P781098 P783186 H770037 H770082 Cancelled ERB B180012 P781098 P781102 P783186 H770037 H770082 Cancelled ERB2 B180016 P785394 P785546 H770037 H770082 Production ERB2 B180017 P785394 X770688 P785546 H770037 H770082 Production PSD D080020 P608533 P600975 P602985 P158914 Production PSD D080026 P608533 P600975 P601735 P158914 Production PSD D080069 P608533 P600975 P785236 P112803 P786050 Production PSD D080070 P608533 P600975 P785237 P112803 P786050 Production PSD D090019 P608665 P606121 P609550 P158914 Production PSD D090020 P608665 P606121 P609550 P158914 Production PSD D090021 P608675 P606121 P609552 P158914 Production PSD D090022 P608675 P606121 P609552 P158914 Production PSD D090073 P608665 P606121 P785651 P112803 P784517 Production PSD D090074 P608665 P606121 P785651 P112803 P784517 Production PSD D090086 P608665 P606121 P785651 P112803 P784517 Production PSD D090087 P608665 P606121 P785651 P112803 P784517 Production PSD D090088 P787281 P606121 P785978 P112803 P784517 Production PSD D090089 P787281 P606121 P785978 P112803 P784517 Production PSD D090090 P608675 P606121 P786989 P112803 P784517 Production PSD D090091 P608675 P606121 P786989 P112803 P784517 Production PSD D090098 P787281 P606121 P785978 P112803 P784517 Production PSD D090099 P787281 P606121 P785978 P112803 P784517 Production PSD D090100 P608675 P606121 P786989 P112803 P784517 Production PSD D090101 P608675 P606121 P786989 P112803 P784517 Production PSD D100029 P608666 P601560 Upon Request P112803 P784517 Production PSD D100030 P608666 P601560 Upon Request P112803 P784517 Production PSD D100031 P608676 P601560 Upon Request P112803 P784517 Production PSD D100032 P608676 P601560 Upon Request P112803 P784517 Production PSD D100121 P608676 P601560 Upon Request P112803 P784517 Production PSD D100122 P608676 P601560 Upon Request P112803 P784517 Production PSD D100123 P608666 P601560 Upon Request P112803 P784517 Production PSD D100124 P608666 P601560 Upon Request P112803 P784517 Production PSD D120035 P608667 P607557 Upon Request P112803 P784517 Production PSD D120036 P608667 P607557 Upon Request P112803 P784517 Production PSD D120037 P608677 P607557 Upon Request P112803 P784517 Production PSD D120038 P608677 P607557 Upon Request P112803 P784517 Production HFD D770065 P772506 P139293 L012244 P126054 Production HFD D770098 P772506 P139293 P126054 Cancelled HFD D770099 P772506 P139293 P126054 Cancelled HFD D770100 P770035 Cancelled HFD D770105 P770991 Cancelled HFD D770106 P772506 P139293 Cancelled HFD D770108 P182041 P119370 Cancelled HFD D770109 P772506 P139293 Cancelled HFD D770112 P772506 P139293 Cancelled HFD D770117 P772506 P139293 L016193 P126054 Production HFD D770121 P772506 P139293 Cancelled FWA G042503 P102745 P102755 P102783 P004055 H770066 Production FPG G042546 P822686 P777153 P522958 P777151 H770066 Production FPG G042575 P822686 P535396 P777153 P522958 P777151 H770066 Production FHG G050003 P182050 P129355 P101870 P002348 H001377 Production FHG G052567 P108736 P118745 Cancelled FHG G052568 P108736 P120949 E500171 P522958 P101870 P002348 Production FHG G052595 P182050 P129355 P101870 P002904 H001377 Production FHG G052596 P182050 P120949 P129355 P101870 P002904 H001377 Production FHG G052667 P182050 P120949 P129355 P181070 P002904 H001377 Cancelled FPG G057502 P772578 P775298 P775308 P522958 P777730 H771377 Production FPG G057504 P772578 P775308 P522958 P777730 H001377 Production FPG G057505 P775631 P775308 P522958 P777730 H001377 Production FWA G065008 P181052 P102805 P101870 P007191 H001378 Production FWA G065055 P101222 Cancelled FHG G065100 P119135 P114500 P111857 P522958 P101870 P007191 H001379 Cancelled FHG G065101 P119135 P114500 P102805 P101870 P002940 H001379 Production FWA G065110 P182052 P102805 P101870 P002940 H001378 Cancelled FHG G065124 P119135 P102805 P101870 P002940 H001379 Cancelled FHG G065188 P119135 P114500 P103836 P105220 P101870 P002940 H001379 Cancelled FHG G065207 P130760 P126984 P111857 P522958 P101870 P002940 H001379 Cancelled FHG G065211 P130760 P111857 P522958 P101870 P002940 H001379 Cancelled FHG G065221 P774510 P770049 P111857 P522958 P181070 P002940 Cancelled FKG G065222 P137293 P137285 Cancelled FKG G065223 P137293 Cancelled FHG G065228 P100760 P111857 P522958 P181070 P002940 Cancelled FKG G065229 P137293 Cancelled FHG G065251 P774510 P770049 Cancelled FLB G065259 P772549 P770181 P522958 P138403 P002940 H001379 Production FLB G065260 P772549 P522958 Production FHG G065310 P130760 P126984 P111857 P522958 P101870 P002940 H001379 Cancelled

Style Air Cleaner Main Safety Cover Vacuator™ U-Clip Wing Mounting Rain Status Model No. Element Element Assembly Valve Mounting (x4) Nut Assy Band Cap

Serv

ice

Parts

Engine Air Cleaners, Accessories & Service Parts 149

Service Parts by Air Cleaner Model

FLB G065311 P772549 P770181 Cancelled FHG G065322 P130760 P126984 P111857 P522958 P101870 P002940 H001379 Cancelled FLB G065337 P771250 P771270 P522958 P130501 Production FLB G065346 P771549 P522958 P002940 Production FKG G065350 P771459 P771460 P522958 P138403 P002940 Production FTG G065357 P775140 P121643 P138403 Cancelled FWA G065390 P182052 P102805 P101870 P002940 Cancelled FWA G065401 P132978 P527908 P522958 P101870 Cancelled FLB G065425 P776675 P776676 P522958 P138403 P002940 H001379 Cancelled FPG G065497 P822768 P822769 P780401 P522958 P778810 H001378 Production FPG G065498 P822768 P780401 P522958 P778810 H001378 Production FPG G065499 P822768 P822769 P780401 P522958 P778810 H001378 Production FPG G065500 P822768 P780401 P522958 P778810 H001378 Production FPG G065539 P532410 P780466 P522958 P778810 H001378 Production FPG G070006 P772579 P775300 P775311 P522958 P777731 H001379 Production FPG G070009 P772579 P775311 P522958 P777731 H771379 Production FPG G070015 P776156 P775311 P522958 P777731 H771379 Cancelled FPG G070059 P772579 P775300 P778758 P522958 P777731 H001379 Production FPG G070060 P772579 P778758 P522958 P777731 H001379 Production FPG G070135 P783498 P775300 P778758 P522958 P777731 H001379 Production FWA G080026 P182054 P112803 P004307 H001379 Cancelled FWA G080119 P182054 Cancelled FHG G080195 P182059 P103113 P101870 P003951 H770010 Cancelled FHG G080200 P182059 P119410 P103113 P101870 P003951 H770010 Production FHG G080227 P182059 P119410 Cancelled FHG G080307 P182059 P119410 Cancelled FHG G080308 P182059 P119410 Cancelled FHG G080322 P772564 P127787 P119711 P158914 P101870 P004307 Cancelled FHG G080364 P774572 P775284 P103840 P112803 P101870 P004307 Cancelled FHG G080365 P774572 P775284 P103113 P101870 P004307 H770010 Cancelled FLB G080377 P772550 P119410 P158914 P101870 P004307 H770010 Production FHG G080394 P182059 P119410 Cancelled FHG G080395 P772564 P127787 P158914 P101870 P004307 Cancelled FLB G080430 P772550 P158914 P004307 H770010 Production FLB G080433 P772553 P127787 Cancelled FHG G080440 P182059 Cancelled FLB G080442 P772554 Production FHG G080458 P772564 P127787 Cancelled FLB G080459 P772550 Cancelled FHG G080463 P182059 P119410 P103837 P112803 P101870 P004307 H770010 Cancelled FWA G080466 P181054 Cancelled FWA G080467 P181054 P781341 Cancelled FHG G080513 P182059 P119410 P103840 P112803 P101870 P004307 Cancelled FLB G080516 P772550 P158914 P004307 Production FLB G080536 P772550 P119410 P158914 P101870 P004307 H770010 Production FLB G080538 P776677 P776678 P158914 P101870 P004307 H770010 Cancelled FPG G082503 P772580 P775302 P775305 P775569 P777732 H770010 Production FPG G082505 P772580 P775305 P775569 P777732 H770010 Production FPG G082508 P772580 P775302 P775305 P522958 P777732 H770010 Production FPG G082511 P772580 P775305 P522958 P777732 H770010 Cancelled FPG G082580 P828889 P829333 P780403 P158914 P780580 H770010 Production FPG G082581 P828889 P780403 P158914 P780580 H770010 Production FPG G082582 P828889 P829333 P780403 P158914 P780580 H770010 Production FPG G082583 P828889 P780403 P158914 P780580 H770010 Production FPG G082671 P828889 P782865 P775569 P777732 H770010 Production FPG G082677 P828889 P782865 P775569 P777732 H770010 Production FHG G090022 P182063 P119778 P112667 P101870 P102025 H770012 Production FHG G090024 P182063 P112667 P101870 P102025 H770012 Production FHG G090031 P182063 P119778 Cancelled FHG G090046 P182063 P119778 P128968 P101870 P004073 Cancelled EKG G090148 P138428 P149099 P137368 P004073 H770090 Cancelled FHG G090185 P774569 P775283 P112667 P101870 P004073 H770012 Cancelled FHG G090190 P182063 P119778 P775725 P112803 P101870 P004073 Cancelled FHG G090203 P182063 P119778 P112667 P101870 P004073 Cancelled FPG G090219 P780522 P780523 P780524 P776008 P780532 H770012 Production FPG G090220 P780522 P780524 P776008 P780532 H770012 Production FPG G090225 P780522 P780523 P780524 P776008 P780532 H770012 Production FPG G090226 P780522 P780524 P776008 P780532 H770012 Production FWA G100003 P182045 P103519 P101401 P004076 H770011 Cancelled FWA G100004 P182045 P103827 P103198 P101401 P004076 H770011 Production FHG G100028 P182064 P103519 E500589 P101870 P106071 H770012 Cancelled FHG G100029 P182064 P119375 P103519 E500589 P101870 P106071 H770012 Cancelled FHG G100035 P182064 P103827 P105220 E500589 P101870 P004076 H770012 Cancelled FHG G100036 P182064 P119375 P103827 P103198 P101401 P111852 P004076 H770012 Cancelled STB G100129 P182090 P119375 P128443 E500589 P101870 P002940 Cancelled FHG G100143 P772545 P133138 P133141 P103198 P128707 P101870 P004076 H770012 Cancelled STB G100154 P182090 P119375 P128443 E500589 P101870 P002940 Cancelled STB G100180 P182090 P119375 Cancelled FWA G100184 P772503 P103827 P105220 E500589 P101870 P004076 H770012 Cancelled FHG G100185 P182064 P133138 P103519 E500589 P101870 P004076 H770012 Cancelled FLB G100220 P772555 P133138 P103198 P138403 P004076 H770012 Production FLB G100221 P772555 P103198 P004076 H770012 Production

Style Air Cleaner Main Safety Cover Vacuator™ Gasket Wing Mounting Rain Status Model No. Element Element Assembly Valve Nut Assy Band Cap

Service Parts

150 Engine Air Cleaners, Accessories & Service Parts

Service Parts by Air Cleaner Model

FLB G100254 P776301 P133138 P103198 P138403 P004076 H770012 Cancelled FLB G100257 P772555 P133138 P103198 P138403 P004076 H770012 Production FLB G100258 P776679 P776680 P103198 P138403 P004076 H770012 Cancelled FRG G100271 P777389 P777388 P777455 P776008 P004076 H770012 Cancelled FPG G100274 P777588 P777589 P158914 INTEGRATED P776343 Production FPG G100275 P777592 P777593 P158914 INTEGRATED P776343 Production FPG G100280 P777588 P777779 P776182 P158914 INTEGRATED P776343 Production FRG G100281 P777638 P777639 P777455 P776008 P004076 H770012 Cancelled FRG G100284 P777638 P777455 P776008 P004076 H770012 Cancelled FPG G100285 P777592 P778776 P777593 P158914 INTEGRATED P776343 Cancelled FLB G100315 P772555 P133138 P103198 P138403 P004076 H770012 Cancelled FPG G100317 P781039 P777639 P780578 P776008 P780594 H770012 Production FPG G100318 P781039 P780578 P776008 P780594 H770012 Production FPG G100319 P781039 P777639 P780578 P776008 P780594 H770012 Production FPG G100320 P781039 P780578 P776008 P780594 H770012 Production FLB G100362 P780067 P780068 Production FPG G100378 P781039 P777639 P780578 P775569 P780594 H770012 Production FRG2 G100420 P785589 X770689 P784944 P776008 P004076 H770012 Production FRG2 G100428 P785589 P784944 P776008 P004076 H770012 Production FRG G110211 P778905 P778906 P778366 P158914 P004079 H770013 Cancelled FRG G110269 P778905 P778906 P778366 P158914 P782257 P004079 H770013 Cancelled FRG2 G110381 P785396 X770690 P784923 P158914 P004079 H770013 Production FRG2 G110382 P785396 X770690 P784923 P158914 P004079 H770013 Production FRG G118329 P821938 P821963 P821825 P806891 P830922 P004079 Cancelled FHG G120012 P182034 P106589 P017804 P111852 P100808 H770013 Production FHG G120014 P182034 P119374 P106589 P017804 P111852 P100808 H770013 Production FHG G120036 P182034 P119374 P109296 P103198 P017804 P111852 H000349 H770013 Cancelled FHG G120037 P182034 P109296 P105220 P017804 P111852 H000349 H770013 Cancelled FHG G120269 P182034 P119374 P106589 P017804 P111852 P100808 H770013 Production FWA G120305 P772504 Cancelled FLB G120309 P772531 P770678 P105220 P138403 H000349 H770013 Production FLB G120310 P772531 P105220 H000349 H770013 Production STG G120332 - See page 115 Production FLB G120359 P772531 P770678 Production FLB G120368 P772531 P770678 P105220 P138403 H000349 H770013 Cancelled STB G120369 P182044 P119371 P109194 P017804 X004816 Cancelled FLB G120386 P781301 P781302 P105220 P138403 H000349 H770013 Production FRG G130061 P777409 P777414 P777408 P776008 P013722 H770090 Cancelled FRG G130087 P777409 P777408 P776008 P013722 H770090 Cancelled FRG G130088 P777409 P777414 P777408 P776008 P013722 H770090 Cancelled FRG G130113 P777409 P777408 P775569 P013722 H770090 Cancelled FRG G130120 P780331 P780332 P777408 P776008 P013722 H770090 Cancelled FRG G130164 P781822 P781826 P777408 P776008 P013722 H770090 Production FRG2 G130232 P785390 X770691 P784892 P776008 P013722 H770090 Production FRG2 G130233 P785390 P784892 P776008 P013722 H770090 Production FRG2 G130234 P785390 X770691 P784892 P776008 P013722 H770090 Production FRG2 G130235 P785390 P784892 P775569 P013722 H770090 Production FRG2 G130236 P785398 X770692 P784892 P776008 P013722 H770090 Production ERG G132034 P777579 P776947 P158914 Cancelled ERG G132036 P532503 P532504 P780533 P778220 P013722 H770013 Cancelled FTG G138217 P777776 P777777 P777709 P806891 P126054 P013722 Cancelled FHG G140022 P182046 P119373 P106773 P017335 P775455 P100866 H770090 Production FHG G140023 P182046 P106773 P017335 P111852 P100866 H770090 Cancelled FHG G140054 P182046 P119373 P109297 P105220 P017335 P775455 P100866 H770090 Production FHG G140055 P182046 P109297 P103198 P017335 P111852 H000350 H770090 Cancelled STB G140059 P182041 P119370 P109084 P017335 X004816 Production STG G140076 - See page 114 Production FWA G140181 P117331 Cancelled FHG G140393 P182046 Cancelled EBA G140420 P772523 P770597 Cancelled FHG G140435 P182046 Cancelled FHG G140436 P182046 P119373 P118784 P017335 P775455 H000350 H770090 Cancelled FHG G140442 P182046 P119373 Cancelled STG G140445 - See page 115 Production EBA G140494 P772523 P119373 P775240 P017335 P775455 H000350 H770090 Cancelled EBA G140496 P772523 P119373 P775240 P017335 P775455 H000350 H770090 Production FTG G140570 P182046 P771385 P105220 P017335 P111852 Cancelled FTG G150029 P772536 P771073 P771178 P103198 P111852 P016845 H770089 Production FTG G150032 P774537 P771178 P103198 P771179 P111852 P016845 H770089 Production FTG G150033 P772567 P771178 P103198 P771179 P111852 P016845 H770089 Production FTG G150034 P772567 P771178 P103198 P771179 P111852 P016845 H770089 Cancelled FTG G150035 P772536 P771073 P771178 P103198 P111852 P016845 H770089 Production FTG G150037 P772536 P771178 P103198 P111852 P016845 H770089 Production FTG G150043 P772581 P775339 P771178 P103198 P771179 P111852 P016845 H770089 Production FTG G150076 P772567 P771178 P103198 P771179 P111852 P016845 Cancelled FRG G150092 P777868 P777869 P777920 P776008 P016845 H770089 Cancelled FTG G150096 P772567 P777938 P771178 P103198 P771179 P111852 P016845 H770089 Cancelled FRG G150097 P777868 P777920 P776008 P016845 H770089 Cancelled SSG G150104 P777871 P777875 P777861 P112803 P017336 Production FRG G150111 P777868 P777869 P777920 P776008 P016845 H770089 Production

Style Air Cleaner Main Safety Cover Vacuator™ Gasket Wing Mounting Rain Status Model No. Element Element Assembly Valve Nut Assy Band Cap

Serv

ice

Parts

Engine Air Cleaners, Accessories & Service Parts 151

Service Parts by Air Cleaner Model

Style Air Cleaner Main Safety Cover Vacuator™ Gasket Wing Mounting Rain Status Model No. Element Element Assembly Valve Nut Assy Band Cap

FRG G150112 P777868 P777869 P777920 P776008 P016845 H770089 Cancelled FRG G150117 P778764 P778765 Cancelled FTG G150165 P772536 P771178 P103198 P771179 P111852 P016845 H770089 Cancelled FRG G150168 P781187 P777875 P777861 P016845 H770089 Cancelled FRG G150169 P781187 P777875 P777861 P016845 H770089 Cancelled FRG G150207 P781909 P777920 P776008 P016845 H770089 Cancelled FRG G150215 P778674 P777875 P777920 P158914 P016845 H770089 Cancelled FRG2 G150255 P785590 X770693 P785551 P776008 P016845 H770089 Production FRG2 G150256 P785590 P785551 P776008 P016845 H770089 Production FRG2 G150259 P785590 X770693 P785551 P776008 P016845 H770089 Production FHG G160048 P182002 P119372 P106639 P017336 P111852 P100789 H770089 Production FHG G160057 P182002 P106621 P017336 P111852 H000351 H770089 Cancelled STG G160077 - See page 114 Production FHG G160078 P182002 P119372 P106952 P103198 P017336 P111852 H000351 H770089 Cancelled STG G160445 - See page 115 Production FHG G160609 P182002 P106621 P017336 P111852 H000351 H770089 Cancelled STG G161006 - See page 114 Production STG G161020 - See page 115 Production FTG G180011 P182042 P128408 P775715 P105220 P116175 H770037 H001053 Production FTG G180013 P182042 P775715 P105220 P116175 H770037 H001053 Cancelled FTG G180014 P182042 P128408 P775715 P105220 P105740 P116175 H770037 H001053 Cancelled FTG G180015 P182042 P105220 P105740 P116175 H770037 H001053 Cancelled FTG G180019 P182042 P128408 P775715 P105220 P105740 P116175 H770037 Cancelled FRG G180026 P531988 P531995 P112803 Cancelled FRG G180031 P781098 P781102 P783185 P105220 H770037 H001053 Cancelled FRG G180033 P781398 P781399 P783185 P105220 H770037 H001053 Cancelled FRG G180035 P781098 P781102 P783185 P105220 H770037 H001053 Cancelled FRG G180038 P781098 P781102 P781084 P105220 H770037 H001053 Cancelled FRG2 G180073 P785394 X770688 P784792 P105220 H770037 H001053 Production FRG2 G180074 P785394 X770688 P784792 P105220 H770037 H001053 Production FRG2 G180075 P785394 X770688 P784792 P105220 H770037 H001053 Production FRG2 G180087 P786197 X770683 P784792 P105220 H770037 H001053 Production SRG G200008 Replaced by SSG200087 SRG G200013 Replaced by SSG200086 SSG G200086 P608306 P608305 P603716 P103198 Production SSG G200087 P608306 P608305 P603716 P103198 Production SSG G200088 P609519 P609518 P603716 P103198 Production FTG G210007 P182040 P117781 P105220 P116175 H770068 H770082 Production FTG G210010 P182040 P117781 P105220 P116175 H770068 H770082 Production FTG G210009 P182040 P117781 P777862 P105220 P116175 H770068 Production FTG G210012 P182040 P117781 P781411 P105220 P116175 H770068 Production SRG G290000 Replaced by SSG290057 SRG G290012 Replaced by SSG290053 SRG G290023 Replaced by SSG290052 SSG G290052 P608306 P608305 P603716 P103198 Production SSG G290053 P608306 P608305 P603716 P103198 Production SSG G290055 P609519 P609518 P603716 P103198 Production SSG G290057 P608306 P608305 P603716 P103198 Production STB G770001 P182039 P114931 Cancelled SRG G772001 P182040 P117781 L015444 P105740 P116175 Production SRG G772002 P182038 P115070 P105740 P116175 Cancelled SRG G772003 P184040 P136659 Cancelled SRG G772004 P182048 P120879 Cancelled SRG G772006 P182038 P115070 Cancelled SRG G772901 P182040 P117781 Production SRG G772902 P182038 P115070 P105740 P116175 Production SRG G772906 P182038 P115070 P105740 P116175 Production SRG G772910 P182038 P115070 Cancelled SRG G772911 P182040 P117781 P105740 P116175 Production SRG G772912 P182040 P117781 P105740 P116175 Production

Service Parts

152 Engine Air Cleaners, Accessories & Service Parts

Parts Listing

Engine Air Cleaners, Accessories & Service Parts 153

B045008 FKB Air Cleaner 50-54

B055006 FKB Air Cleaner 50-54

B065018 FLB Air Cleaner 90-92B065045 FKB Air Cleaner 50-54B070005 EPB Air Cleaner 43-48B080022 FLB Air Cleaner 90-92B080067 EPB Air Cleaner 43-48B080080 XRB Air Cleaner 56-59B085001 ECB Duralite™ Air Cleaner 38-42B085011 ECB Duralite™ Air Cleaner 38-42B085046 ECB Duralite™ Air Cleaner 38-42B085048 ECB Duralite™ Air Cleaner 38-42B085056 ECB Duralite™ Air Cleaner 38-42B095437 SRB Air Cleaner 100-103

B100067 FLB Air Cleaner 90-92

B100094 ECB Duralite™ Air Cleaner 38-42

B100120 ERB Air Cleaner 45

B100121 SRB Air Cleaner 100-103

B100126 ERB2 Air Cleaner 43-48

B100127 XRB Air Cleaner 56-59

B105002 ECB Duralite™ Air Cleaner 38-42

B105006 ECB Duralite™ Air Cleaner 38-42

B105012 ECB Duralite™ Air Cleaner 38-42

B110155 SRB Air Cleaner 100-103

B120260 FLB Air Cleaner 90-92

B120376 ECB Duralite™ Air Cleaner 38-42

B120470 XRB Air Cleaner 56-59

B125003 ECB Duralite™ Air Cleaner 38-42

B125005 ECB Duralite™ Air Cleaner 38-42

B125011 ECB Duralite™ Air Cleaner 38-42

B130010 ERB Air Cleaner 45

B130013 ERB Air Cleaner 45

B130046 SRB Air Cleaner 100-103

B130048 SPB2 Air Cleaner 97-99

B130057 ERB2 Air Cleaner 43-48

B130058 ERB2 Air Cleaner 43-48

B130060 SPB2 Air Cleaner 97-99

B150025 ERB Air Cleaner 45

B150028 ERB Air Cleaner 45

B150058 ERB2 Air Cleaner 43-48

B150059 ERB2 Air Cleaner 43-48

B180011 ERB Air Cleaner 45

B180012 ERB Air Cleaner 45

B180016 ERB2 Air Cleaner 43-48

B180017 ERB2 Air Cleaner 43-48

C045001 ECC Duralite™ Air Cleaner 38-42

C045002 ECC Duralite™ Air Cleaner 38-42

C055002 ECC Duralite™ Air Cleaner 38-42

C055003 ECC Duralite™ Air Cleaner 38-42

C055008 ECC Duralite™ Air Cleaner 38-42

C065001 ECC Duralite™ Air Cleaner 38-42

C065002 ECC Duralite™ Air Cleaner 38-42

C065003 ECC Duralite™ Air Cleaner 38-42

C065004 ECC Duralite™ Air Cleaner 38-42

C065015 ECC Duralite™ Air Cleaner 38-42

C085001 ECC Duralite™ Air Cleaner 38-42

C085002 ECC Duralite™ Air Cleaner 38-42

C085003 ECC Duralite™ Air Cleaner 38-42

C085004 ECC Duralite™ Air Cleaner 38-42

C085005 ECC Duralite™ Air Cleaner 38-42

C085006 ECC Duralite™ Air Cleaner 38-42

C105003 ECC Duralite™ Air Cleaner 38-42

C105004 ECC Duralite™ Air Cleaner 38-42

C125003 ECC Duralite™ Air Cleaner 38-42

C125004 ECC Duralite™ Air Cleaner 38-42

D045003 ECD Duralite™ Air Cleaner 38-42

D045004 ECD Duralite™ Air Cleaner 38-42

D055004 ECD Duralite™ Air Cleaner 38-42

D065003 ECD Duralite™ Air Cleaner 38-42

D065008 ECD Duralite™ Air Cleaner 38-42

D080020 PSD PowerCore® Air Cleaner 27

D080026 PSD PowerCore® Air Cleaner 27

D080069 PSD PowerCore® Air Cleaner 19-35

D080070 PSD PowerCore® Air Cleaner 19-35

D085011 ECD Duralite™ Air Cleaner 38-42

D085012 ECD Duralite™ Air Cleaner 38-42

D090019 PSD PowerCore® Air Cleaner 27

D090020 PSD PowerCore® Air Cleaner 27

D090021 PSD PowerCore® Air Cleaner 27

D090022 PSD PowerCore® Air Cleaner 27

D090073 PSD PowerCore® Air Cleaner 19-35

D090074 PSD PowerCore® Air Cleaner 19-35

D090086 PSD PowerCore® Air Cleaner 19-35

D090087 PSD PowerCore® Air Cleaner 19-35

D090088 PSD PowerCore® Air Cleaner 19-35

D090089 PSD PowerCore® Air Cleaner 19-35

D090090 PSD PowerCore® Air Cleaner 19-35

D090091 PSD PowerCore® Air Cleaner 19-35

D090098 PSD PowerCore® Air Cleaner 19-35

D090099 PSD PowerCore® Air Cleaner 19-35

D090100 PSD PowerCore® Air Cleaner 19-35

D090101 PSD PowerCore® Air Cleaner 19-35

D100029 PSD PowerCore® Air Cleaner 19-35

D100030 PSD PowerCore® Air Cleaner 19-35

D100031 PSD PowerCore® Air Cleaner 19-35

D100032 PSD PowerCore® Air Cleaner 19-35

D100121 PSD PowerCore® Air Cleaner 19-35

D100122 PSD PowerCore® Air Cleaner 19-35

D100123 PSD PowerCore® Air Cleaner 19-35

D100124 PSD PowerCore® Air Cleaner 19-35

D120035 PSD PowerCore® Air Cleaner 19-35

D120036 PSD PowerCore® Air Cleaner 19-35

D120037 PSD PowerCore® Air Cleaner 19-35

D120038 PSD PowerCore® Air Cleaner 19-35

D125004 ECD Duralite™ Air Cleaner 38-42

E500206 Metal Mounting Band 129

G042546 FPG Air Cleaner 64-69

G042575 FPG Air Cleaner 64-69

G057502 FPG Air Cleaner 64-69

G057504 FPG Air Cleaner 64-69

G057505 FPG Air Cleaner 64-69

G065497 FPG Alexin™ Air Cleaner 70-76

G065498 FPG Alexin™ Air Cleaner 70-76

G065499 FPG Alexin™ Air Cleaner 70-76

G065500 FPG Alexin™ Air Cleaner 70-76

G070006 FPG Air Cleaner 64-69

G070009 FPG Air Cleaner 64-69

G070059 FPG Air Cleaner 64-69

G070060 FPG Air Cleaner 64-69

G082503 FPG Air Cleaner 64-69

G082505 FPG Air Cleaner 64-69

G082508 FPG Air Cleaner 64-69

G082580 FPG Alexin™ Air Cleaner 70-76

Part Product PageNumber Description Number

Part Product PageNumber Description Number

Parts Listing

Parts Listing

154 Engine Air Cleaners, Accessories & Service Parts

Part Product PageNumber Description Number

Part Product PageNumber Description Number

G082581 FPG Alexin™ Air Cleaner 70-76

G082582 FPG Alexin™ Air Cleaner 70-76

G082583 FPG Alexin™ Air Cleaner 70-76

G090219 FPG Alexin™ Air Cleaner 70-76

G090220 FPG Alexin™ Air Cleaner 70-76

G090225 FPG Alexin™ Air Cleaner 70-76

G090226 FPG Alexin™ Air Cleaner 70-76

G100274 FPG Air Cleaner 64-69

G100275 FPG Air Cleaner 64-69

G100280 FPG Air Cleaner 64-69

G100281 FRG Air Cleaner 83

G100284 FRG Air Cleaner 83

G100317 FPG Alexin™ Air Cleaner 70-76

G100318 FPG Alexin™ Air Cleaner 70-76

G100319 FPG Alexin™ Air Cleaner 70-76

G100320 FPG Alexin™ Air Cleaner 70-76

G100420 FRG2 Air Cleaner 82-88

G100428 FRG2 Air Cleaner 82-88

G110211 FRG Air Cleaner 83

G110269 FRG Air Cleaner 83

G110381 FRG2 Air Cleaner 82-88

G110382 FRG2 Air Cleaner 82-88

G120332 STG Air Cleaner 111-117

G130061 FRG Air Cleaner 83

G130087 FRG Air Cleaner 83

G130088 FRG Air Cleaner 83

G130113 FRG Air Cleaner 83

G130120 FRG Air Cleaner 83

G130232 FRG2 Air Cleaner 82-88

G130233 FRG2 Air Cleaner 82-88

G130234 FRG2 Air Cleaner 82-88

G130235 FRG2 Air Cleaner 82-88

G130236 FRG2 Air Cleaner 82-88

G140076 STG Air Cleaner 80-83

G140445 STG Air Cleaner 111-117

G140076 STG Air Cleaner 111-117

G140077 STG Air Cleaner 80-83

G150092 FRG Air Cleaner 83

G150097 FRG Air Cleaner 83

G150112 FRG Air Cleaner 83

G150255 FRG2 Air Cleaner 82-88

G150256 FRG2 Air Cleaner 82-88

G150259 FRG2 Air Cleaner 82-88

G160077 STG Air Cleaner 111-117

G160445 STG Air Cleaner 111-117

G161006 STG Air Cleaner 111-117

G161020 STG Air Cleaner 111-117

G180031 FRG Air Cleaner 83

G180033 FRG Air Cleaner 83

G180035 FRG Air Cleaner 83

G180038 FRG Air Cleaner 83

G180073 FRG2 Air Cleaner 82-88

G180074 FRG2 Air Cleaner 82-88

G180075 FRG2 Air Cleaner 82-88

G180087 FRG2 Air Cleaner 82-88

G200008 SRG Axial Seal, Metal Air Cleaner 76-79

G200013 SRG Axial Seal, Metal Air Cleaner 76-79

G200086 SSG Air Cleaner 104-110

G200087 SSG Air Cleaner 104-110

G200088 SSG Air Cleaner 104-110

G210007 FTG Air Cleaner 78-81

G210010 FTG Air Cleaner 78-81

G290000 SRG Axial Seal, Metal Air Cleaner 76-79

G290012 SRG Axial Seal, Metal Air Cleaner 76-79

G290023 SRG Axial Seal, Metal Air Cleaner 76-79

G290052 SSG Air Cleaner 104-110

G290053 SSG Air Cleaner 104-110

G290055 SSG Air Cleaner 104-110

G290057 SSG Air Cleaner 104-110

H000349 Metal Mounting Band 90, 115, 129

H000350 Metal Mounting Band 114, 115, 129

H000351 Metal Mounting Band 114, 115, 129

H000606 STG Air Inlet Hood 115

H000820 PBH Full-View Pre-Cleaner 131

H000821 PBH Full-View Pre-Cleaner 131

H000822 PBH Full-View Pre-Cleaner 131

H000823 PBH Full-View Pre-Cleaner 60, 131

H000875 In-Line Separators 127

H000878 In-Line Separators 127

H000886 In-Line Separators 127

H000896 PCH Pre-Cleaner 95

H000975 PCH Pre-Cleaner 95

H001032 Standard Ejector 125

H001033 Standard Ejector 125

H001034 Standard Ejector 125

H001035 Standard Ejector 125

H001039 Standard Ejector 125

H001053 Rain Cap 84, 134

H001148 PCH Pre-Cleaner 95

H001212 PLH Donaspin™ Pre-Cleaner 93, 130

H001215 PLH Donaspin™ Pre-Cleaner 93, 130

H001220 In-Line Separators 127

H001249 PBH Full-View Pre-Cleaner 60, 131

H001250 PBH Full-View Pre-Cleaner 131

H001251 PBH Full-View Pre-Cleaner 131

H001277 Compact Style Ejector 125

H001278 Compact Style Ejector 125

H001279 Compact Style Ejector 125

H001280 Compact Style Ejector 125

H001281 Compact Style Ejector 125

H001282 Compact Style Ejector 125

H001283 Compact Style Ejector 125

H001284 Compact Style Ejector 125

H001307 PLH Donaspin™ Pre-Cleaner 93, 130

H001308 PLH Donaspin™ Pre-Cleaner 130

H001375 PLH Donaspin™ Pre-Cleaner 130

H001377 Rain Cap 67, 134

H001378 Rain Cap 73, 134

H001379 Rain Cap 44, 67, 134

H001474 In-Line Separators 127

H001510 PCH Pre-Cleaner 95

H001906 In-Line Separators 127

H002040 PBH Full-View Pre-Cleaner 131

H002041 PBH Full-View Pre-Cleaner 131

H002042 PBH Full-View Pre-Cleaner 131

H002043 PBH Full-View Pre-Cleaner 131

H002129 Expanded Inlet End Style Ejector 125

H002132 Expanded Inlet End Style Ejector 125

H002223 PBH Full-View Pre-Cleaner 131

H002224 PBH Full-View Pre-Cleaner 60, 131

H002394 PTH TopSpin™ Pre-Cleaner 133

H002425 PTH TopSpin™ Pre-Cleaner 133

Parts

Lis

ting

Parts Listing

Engine Air Cleaners, Accessories & Service Parts 155

Part Product PageNumber Description Number

Part Product PageNumber Description Number

H002426 PTH TopSpin™ Pre-Cleaner 62, 133

H002427 PTH TopSpin™ Pre-Cleaner 62, 133

H002431 PTH TopSpin™ Pre-Cleaner 133

H002432 PTH TopSpin™ Pre-Cleaner 133

H002433 PTH TopSpin™ Pre-Cleaner 133

H002434 PTH TopSpin™ Pre-Cleaner 133

H002435 PTH TopSpin™ Pre-Cleaner 133

H002436 PTH TopSpin™ Pre-Cleaner 133

H002437 PTH TopSpin™ Pre-Cleaner 62, 133

H002438 PTH TopSpin™ Pre-Cleaner 133

H002439 PTH TopSpin™ Pre-Cleaner 62, 133

H105740 FTG Gasket Washer 79

H770010 Rain Cap 44, 67, 73, 134

H770011 Rain Cap 134

H770012 Rain Cap 45, 73, 84, 134

H770013 Rain Cap 84, 134

H770025 Metal Mounting Band 129

H770037 Metal Mounting Band 45, 84, 129

H770059 Metal Mounting Band 129

H770065 Metal Mounting Band 129

H770066 Rain Cap 67, 134

H770068 Metal Mounting Band 79, 129

H770081 Rain Cap 134

H770082 Rain Cap 45, 79, 134

H770089 Rain Cap 45, 84, 134

H770090 Rain Cap 84, 134

P002348 Metal Mounting Band 129

P002351 Metal Mounting Band 129

P004055 Metal Mounting Band 129

P004073 Metal Mounting Band 101, 129

P004076 Metal Mounting Band 45, 84, 90, 101, 129

P004079 Metal Mounting Band 84, 101, 129

P004307 Metal Mounting Band 90, 129

P004906 Metal Mounting Band 129

P007191 Metal Mounting Band 90, 129

P013722 Metal Mounting Band 45, 84, 101, 129

P016330 Bowl Full-View Pre-Cleaner 131

P016548 Cover Full-View Pre-Cleaner 131

P016845 Metal Mounting Band 45, 84, 129

P016972 STG Gasket, Cover 114, 115

P017281 SSG20/29 Cover Chain 107, 108

P017283 SSG20/29 Chain Connector 107, 108

P017335 STG Gasket, Body or Cup 114, 115

P017336 STG Gasket , Body or Cup 114, 115

P017365 STG Gasket, Cover 115

P017367 STG Gasket, Cover 114, 115

P017617 STG Cover Latch Assembly 114, 115

P017804 SSG20/29 Dust Cup Gasket 107, 108

P020115 Bowl Full-View Pre-Cleaner 131

P020116 Cover Full-View Pre-Cleaner 131

P020227 Bowl Full-View Pre-Cleaner 131

P020344 Bowl Full-View Pre-Cleaner 131

P020345 Cover Full-View Pre-Cleaner 131

P020648 Cover Full-View Pre-Cleaner 131

P100780 STG Clamp, Body 114

P100789 STG Clamp, Cup 114

P100794 STG Dust Cup 114, 115

P100808 SSG20/29 Dust Cup Clamp 107, 108

P100860 STG Dust Cup 114, 115

P100866 STG Clamp, Cup 114

P101290 Hump Reducer 139

P101291 Hump Reducer 139

P101292 Hump Reducer 139

P101293 Hump Reducer 139

P101294 Hump Reducer 139

P101759 STG Inlet Shroud - Optional 114

P101891 Hump Reducer 139

P102256 STG Body, Lower 114

P102820 Hump Reducer 139

P102870 STG Inlet Shroud - Optional 114

P102948 Reducer 139

P103198 Vacuator™ Valve 107, 108, 141

P103516 Hump Reducer 139

P103530 STG Dust Cup, Vac Valve, Horz 114, 115

P103746 STG Dust Cup, Vac Valve, Horz 115

P104087 Reducer 139

P104088 Reducer 139

P104089 Reducer 139

P104090 Reducer 139

P104694 Cover Full-View Pre-Cleaner 131

P104973 STG Dust Cup, Vac Valve, Vert 114, 115

P105016 STG Dust Cup, Vac Valve, Vert 115

P105220 Vacuator™ Valve 79, 84, 141

P105529 90° Elbow 137

P105530 90° Elbow 137

P105531 90° Elbow 137

P105532 90° Elbow 137

P105533 90° Elbow 137

P105534 90° Elbow 137

P105535 90° Elbow 137

P105536 90° Elbow 137

P105541 45° Elbow 138

P105542 45° Elbow 138

P105543 45° Elbow 138

P105544 45° Elbow 138

P105545 45° Elbow 138

P105546 45° Elbow 138

P105547 45° Elbow 138

P105548 45° Elbow 138

P105608 Straight Hump 138

P105609 Straight Hump 138

P105610 Straight Hump 138

P105611 Straight Hump 138

P105612 Straight Hump 138

P105613 Straight Hump 138

P105740 FTG, STG Gasket Washer 78, 114, 115

P106593 Vacuator™ Valve 106, 141

P107375 STG Dust Cup, Quick Release 115

P107377 STG Dust Cup, Quick Release 114, 115

P107844 90° Elbow 137

P109021 45° Elbow 138

P109062 Wing Nut 114

P109153 STG Cover 114, 115

P109331 45° Elbow 138

P110875 STG Body, Lower 115

P111414 Straight Hump 138

P112605 90° Elbow 137

P112606 45° Elbow 138

P112607 Hump Reducer 139

P112608 Straight Hump 138

P112609 Hump Reducer 139

P112610 Hump Reducer 139

Parts Listing

Parts Listing

156 Engine Air Cleaners, Accessories & Service Parts

P112611 Hump Reducer 139

P112803 Vacuator™ Valve 26, 141

P113733 90° Elbow 137

P114100 STG Lower Body 115

P114313 45° Elbow 138

P114314 90° Elbow 137

P114315 Hump Reducer 139

P114316 45° Elbow 138

P114317 Straight Hump 138

P114318 90° Elbow 137

P114319 Straight Hump 138

P114411 Reducer 139

P114412 Reducer 139

P114931 STG Safety Element 114, 115

P115023 STG Body, Lower 114

P115096 SSG29 Body Gasket Strips - two, long 108

P115098 SSG20/29 Body Gasket Strips - two, short 107, 108

P115110 SSG29 Lower Body Assembly 108

P115200 Lined Hose Clamp 120, 125, 131

P115201 Lined Hose Clamp 120, 131

P115202 Lined Hose Clamp 120, 131

P115203 Lined Hose Clamp 120, 131

P115204 High Torque Clamp 120

P115205 High Torque Clamp 120

P115206 High Torque Clamp 120

P115207 High Torque Clamp 120

P115208 High Torque Clamp 120

P115209 High Torque Clamp 120

P116175 FTG Wing Nut 79

P117724 90° Elbow Reducer 137

P117781 FTG Safety Element 79

P117785 SSG20 Lower Body Assembly 107

P117791 SSG20 Body Gasket Strips - two, long 107

P118552 SSG29 Lower Body Assembly 108

P119370 STG Safety Element 114, 115

P119371 STG Safety Element 114

P119410 FLB Safety Element 90

P119874 SSG20/29 Rain Shroud, Right Side 107, 108

P119875 SSG20/29 Rain Shroud, Left Side 107, 108

P119876 SSG20 Rain Shroud, Front 107

P119877 SSG29 Rain Shroud, Front 108

P121482 90° Elbow Reducer 137

P123462 90° Elbow Reducer 137

P126530 Hump Reducer 139

P128408 FTG Safety Element 114, 115

P128990 90° Elbow Reducer 137

P129660 Hump Reducer 139

P133138 FLB Safety Element 90

P133338 45° Elbow Reducer 138

P133339 45° Elbow Reducer 138

P136494 Hump Reducer 139

P138403 Filter Wing Nut 90

P143422 Lined Hose Clamp 120, 131

P143895 90° Elbow Reducer 137

P148337 T-Bolt Clamp 120

P148338 T-Bolt Clamp 120

P148339 T-Bolt Clamp 120

P148340 T-Bolt Clamp 120

P148341 T-Bolt Clamp 120

P148342 T-Bolt Clamp 120

P148343 T-Bolt Clamp 120

P148344 T-Bolt Clamp 120

P148345 T-Bolt Clamp 120

P148346 T-Bolt Clamp 120

P148347 T-Bolt Clamp 120

P148348 T-Bolt Clamp 120

P148349 T-Bolt Clamp 120

P148350 T-Bolt Clamp 120

P149099 Vacuator™ Valve 106, 141

P158089 SSG20/29 Dust Cup 107, 108

P158324 Bowl Full-View Pre-Cleaner 131

P158914 Vacuator™ Valve 57, 67, 73, 84, 141

P159820 90° Elbow Reducer 137

P171376 3-Ply Silicone Scavenge Hose 125

P171378 3-Ply Silicone Scavenge Hose 125

P171381 3-Ply Silicone Scavenge Hose 125

P181039 STG Main Element 114, 115

P181041 STG Main Element 114, 115

P181042 STG Main Element 114, 115

P181044 STG Main Element 115

P182039 STG Main Element 114, 115

P182040 FTG Main Element 79

P182041 STG Main Element 114, 115

P182042 STG Main Element 114, 115

P182044 STG Main Element 115

P185039 STG Donaldson Endurance™ Mail Element 114, 115

P185041 STG Donaldson Endurance™ Main Element 114, 115

P185042 STG Donaldson Endurance™ Main Element 115

P185044 STG Donaldson Endurance™ Main Element 115

P185052 STG Donaldson Endurance™ Main Element 114

P185152 SSG20/29 Donaldson Endurance™ Main Element 107, 108

P185153 SSG20/29 Donaldson Endurance™ Main Element 107, 108

P520882 Hump Reducer 139

P520883 Hump Reducer 139

P520884 Hump Reducer 139

P522958 Vacuator™ Valve 67, 73, 114

P525956 Vacuator™ Valve 106, 114

P532919 Lined Hose Clamp 120

P532920 Lined Hose Clamp 120

P532921 Lined Hose Clamp 120

P532922 Lined Hose Clamp 120

P532923 Lined Hose Clamp 120

P532924 Lined Hose Clamp 120, 125, 131

P532925 Constant Torque Clamp 120

P532926 Constant Torque Clamp 120

P532927 Constant Torque Clamp 120

P532928 Constant Torque Clamp 120

P532929 Constant Torque Clamp 120

P532943 4-Ply Below 140

P532944 4-Ply Below 140

P532945 4-Ply Below 140

P532946 Connector/Sleeve 140

P532947 Connector/Sleeve 140

P532948 Connector/Sleeve 140

P532949 Connector/Sleeve 140

P532950 Connector/Sleeve 140

P532951 Connector/Sleeve 140

P532952 Connector/Sleeve 140

P532953 Connector/Sleeve 140

P532954 Connector/Sleeve 140

P532956 Connector/Sleeve 140

P532957 Connector/Sleeve 140

Part Product PageNumber Description Number

Part Product PageNumber Description Number

Parts

Lis

ting

Parts Listing

Engine Air Cleaners, Accessories & Service Parts 157

P532958 Connector/Sleeve 140

P532959 Connector/Sleeve 140

P532960 Hump Hose Connector 140

P532961 Hump Hose Connector 140

P532962 Hump Hose Connector 140

P535396 FPG Safety Element 67

P535571 4-Ply Below 140

P535572 4-Ply Below 140

P535573 4-Ply Below 140

P541619 FPG Cover Assy 48

P544356 FPG Cover Assy 48

P544357 FPG Cover Assy 48

P600975 PSD Safety Element 26

P601560 PSD Safety Element 26

P602427 FKB04 Safety Element 52

P603504 SSG20/29 Body Gasket Strips - two, short 107, 108

P603505 SSG20 Lower Body Assembly 107

P603716 SSG20/29 Cover 107, 108

P603729 FKB04 Safety Element 52

P604457 FKB04 Main Element 52

P605731 XRB Cover Assy 57

P606121 PSD Safety Element 26

P606497 FKB04 Cover Assy 52

P607557 PSD Safety Element 26

P608116 XRB Main Element 57

P608117 XRB Cover Assy 57

P608305 SSG20/29 Safety Element 107, 108

P608306 SSG20/29 Main Element 107, 108

P608391 XRB Safety Element 57

P608533 PSD Main Element 26

P608592 FKB06 Cover Assy 52

P608599 FKB06 Safety Element 52

P608665 PSD Main Element 26

P608666 PSD Main Element 26

P608667 PSD Main Element 26

P608675 PSD Main Element 26

P608676 PSD Main Element 26

P608677 PSD Main Element 26

P609218 FKB05 Main Element 52

P609219 FKB05 Cover Assy 52

P609221 FKB06 Main Element 52

P609508 SSG29 Lower Body Assembly 108

P609518 SSG20/29 Safety Element 107, 108

P609519 SSG20/29 Main Element 107, 108

P609942 XRB Cover Assy 57

P610776 SSG20/29 Rain Shroud, Right Side 107, 108

P610777 SSG20/29 Rain Shroud, Left Side 107, 108

P611189 XRB Safety Element 57

P611190 XRB Main Element 57

P611539 XRB Main Element 57

P611540 XRB Safety Element 57

P770207 FLB Safety Element 90

P770678 FLB Safety Element 90

P771039 SRB Main Element 101

P772520 FLB Main Element 90

P772530 FLB Main Element 90

P772556 FLB Main Element 90

P772565 FLB Main Element 90

P772578 FPG Main Element 67

P772579 EPB, FPG Main Element 44, 67

P772580 EPB, FPG Main Element 44, 67

P775228 90° Elbow Reducer 137

P775298 FPG Safety Element 67

P775300 EPB, FPG Safety Element 44, 67

P775302 EPB, FPG Safety Element 44, 67

P775305 EPB, FPG Cover Assy 44, 67

P775308 FPG Safety Element 67

P775311 FPG Safety Element 67

P775569 Vacuator™ Valve 67, 84, 114

P775631 FPG Main Element 67

P776008 Vacuator™ Valve 73, 84, 114

P776343 Rain Cap 67, 77

P777151 Plastic Mounting Band 67

P777153 FPG Safety Element 67

P777279 SRB Main Element 101

P777414 SRB Safety Element 101

P777588 FPG Main Element 67

P777589 FPG Safety Element 67

P777592 FPG Main Element 67

P777593 FPG Safety Element 67

P777639 FPG Alexin™, SRB Safety Element 73, 101

P777730 Plastic Mounting Band 67, 77

P777731 Plastic Mounting Band 44, 67, 77

P777732 Plastic Mounting Band 44, 67, 77

P777779 FPG Safety Element 67

P777998 SRB Cover Assy 101

P778214 RadialSeal™ Main Element 27,61

P778565 90° Elbow Reducer 137

P778758 EPB, FPG Cover Assy 44, 67

P778776 RadialSeal™ Safety Element 41

P778810 Plastic Mounting Band 77

P778901 Plastic Mounting Band 77

P778905 SRB Main Element 101

P778906 SRB Safety Element 101

P780378 Plastic Mounting Band 77

P780401 FPG Alexin™ Cover Assy 73

P780403 FPG Alexin™ Cover Assy 73

P780522 FPG Alexin™, SRB Main Element 73, 101

P780523 FPG Alexin™, SRB Safety Element 73, 101

P780524 FPG Alexin™ Cover Assy 73

P780532 Plastic Mounting Band 73, 77

P780578 FPG Alexin™ Cover Assy 73

P780580 Plastic Mounting Band 77

P780594 Plastic Mounting Band 73, 77

P781039 FPG Alexin™ Main Element 73

P781124 SRB Cover Assy 101

P781509 90° Elbow 137

P781510 90° Elbow Reducer 137

P781511 Straight Hump 138

P781831 Plastic Mounting Band 77

P782176 SRB Cover Assy 101

P782578 FPG Main Element 67

P783014 SRB Cover Assy 101

P783543 SPB2 Main Element 99

P783693 ERB2, SPB2 Cover Assy 45, 99

P783746 PSD Adapter 26

P783747 PSD Adapter 26

P783748 PSD Adapter 26

P784019 PSD Adapter (PP) 26

P784517 PSD U-Clip Mounting (x4) 26

P784790 PSD Check Valve 26

P784792 FRG2 Cover Assy 84

Part Product PageNumber Description Number

Part Product PageNumber Description Number

Parts Listing

P784834 PSD Adapter (PA) 26

P784869 ERB2 Cover Assy 45

P784892 FRG2 Cover Assy 84

P784923 FRG2 Cover Assy 84

P784944 FRG2 Cover Assy 84

P784954 ERB2 Cover Assy 45

P785236 PSD Cover Assy 26

P785237 PSD Cover Assy 26

P785388 ERB2 Main Element 45

P785390 FRG2 Main Element 84

P785394 ERB2, FRG2 Main Element 45, 84

P785396 FRG2 Main Element 84

P785398 FRG2 Main Element 84

P785426 ERB2 Main Element 45

P785546 ERB2 Cover Assy 45

P785551 FRG2 Cover Assy 84

P785589 FRG2 Main Element 84

P785590 FRG2 Main Element 84

P785610 ERB2 Main Element 45

P785651 PSD Cover Assy 26

P785978 PSD Cover Assy 26

P786050 PSD U-Clip Mounting (x4) 26

P786197 FRG2 Main Element 84

P786337 In-Line Check Valve 126

P786338 In-Line Check Valve 126

P786339 In-Line Check Valve 126

P786340 In-Line Check Valve 126

P786341 In-Line Check Valve 126

P786342 In-Line Check Valve 126

P786343 In-Line Check Valve 126

P786344 In-Line Check Valve 126

P786345 In-Line Check Valve 126

P786685 PSD Adapter 26

P786778 PSD Adapter 26

P786989 PSD Cover Assy 26

P787281 PSD Main Element 26

P822686 FPG, FPG Alexin™ Main Element 67, 72

P822768 FPG Alexin™ Main Element 73

P822769 FPG Alexin™ Safety Element 73

P828889 FPG Alexin™ Main Element 73

P829333 FPG Alexin™ Safety Element 73

X002250 Mechanical, ServiSignal™ Indicator 136

X002251 Mechanical, ServiSignal™ Indicator 136

X002252 Mechanical, ServiSignal™ Indicator 136

X002254 Mechanical, ServiSignal™ Indicator 136

X002275 Mechanical, Informer™ Indicator 136

X002277 Mechanical, Informer™ Indicator 136

X002278 Mechanical, Informer™ Indicator 136

X003538 STG Gasket Kit 114, 115

X003539 STG Gasket Kit 114, 115

X003691 Moisture Eliminator 128

X004476 Flat Band SealClamp™ 121

X004478 Flat Band SealClamp™ 121

X004480 Flat Band SealClamp™ 121

X004482 Flat Band SealClamp™ 121

X004484 Flat Band SealClamp™ 121

X004536 Flat Band SealClamp™ 121

X004537 Flat Band SealClamp™ 121

X004538 Flat Band SealClamp™ 121

X004539 Flat Band SealClamp™ 121

X004816 Safety Signal Indicator 114

X004962 Flat Band SealClamp™ 121

X005164 Preformed SealClamp™ 121

X005265 Preformed SealClamp™ 121

X005555 STG Sprint Clip & Pin 114, 115

X005822 Moisture Skimmer 128

X005900 Moisture Skimmer 128

X005901 Moisture Skimmer 128

X005921 Flat Band / Performed SealClamp™ 121

X006202 Flat Band SealClamp™ 121

X006203 Flat Band SealClamp™ 121

X006204 Flat Band SealClamp™ 121

X006561 Drop Down Tube Extension 122

X006562 Drop Down Tube Extension 122

X007057 Preformed SealClamp™ 121

X007784 Stepped Preformed SealClamp™ 121

X007785 Stepped Preformed SealClamp™ 121

X007805 Stepped Preformed SealClamp™ 121

X007824 Stepped Preformed SealClamp™ 121

X007829 Stepped Preformed SealClamp™ 121

X007830 Stepped Preformed SealClamp™ 121

X007831 Stepped Preformed SealClamp™ 121

X007832 Stepped Preformed SealClamp™ 121

X007833 Stepped Preformed SealClamp™ 121

X007834 Stepped Preformed SealClamp™ 121

X770037 Electrical Indicator 136

X770050 Electrical Indicator 136

X770052 Electrical Indicator 136

X770061 Electrical Indicator 136

X770062 Electrical Indicator 136

X770075 Electrical Indicator 136

X770225 Electrical with AMP Connector Indicator 136

X770301 Electrical with AMP Connector Indicator 136

X770316 Electrical with AMP Connector Indicator 136

X770317 Electrical with AMP Connector Indicator 136

X770526 Electrical with AMP Connector Indicator 136

X770683 FRG2 Kit (Main+Safety) 84

X770684 SPB2 Kit (Main+Safety) 99

X770685 ERB2 Kit (Main+Safety) 45

X770686 ERB2 Kit (Main+Safety) 45

X770687 ERB2 Kit (Main+Safety) 45

X770688 ERB2, FRG2 Kit (Main+Safety) 45, 84

X770689 FRG2 Kit (Main+Safety) 84

X770690 FRG2 Kit (Main+Safety) 84

X770691 FRG2 Kit (Main+Safety) 84

X770692 FRG2 Kit (Main+Safety) 84

X770693 FRG2 Kit (Main+Safety) 84

Part Product PageNumber Description Number

Part Product PageNumber Description Number

Parts Listing

158 Engine Air Cleaners, Accessories & Service Parts

Parts

Lis

ting

EUROPEAN HEADQUARTERSDonaldson Europe B.V.B.A.Interleuvenlaan 1 - Research Park Zone 1 - 3001 Leuven - BelgiumPhone +32 16 38 38 11 - Fax +32 16 38 37 14

EUROPEAN OFFICESDonaldson France S.A.S / Bron - FrancePhone +33 47 21 41 840 - Fax +33 47 82 67 756

Donaldson Ibérica, Soluciones en Filtración, S.L. / Madrid - SpainPhone +34 91 676 86 68 - Fax +34 91 676 87 62

Donaldson Filter Components Ltd. / Hull - UKPhone +44 14 82 83 52 13 - Fax +44 14 82 83 54 11

Donaldson Gesellschaft m.b.H. / Dülmen (Dernekamp) - GermanyPhone +49 2594 78153 / +49 2594 78126 - Fax +49 2594 78178

Donaldson Italia SRL / Ostiglia (Mantova) - ItalyPhone +39 38 63 02 11 - Fax +39 38 68 00 405

Donaldson Sweden / Bromma - SwedenPhone +46 8 471 8660- Fax +46 8 372470

[email protected]

Donaldson Europe B.V.B.A. - Technical Air Catalogue - Brochure No. F116005 (June, 2009)

Donaldson Filtre Sist. Tic. Ltd. / Istanbul - Turkey Phone +90 (212) 244 73 31 – Fax +90 (212) 252 56 33

Donaldson Poland / Gdynia - PolandPhone + Fax +48 58 625 70 66

Donaldson Bulgaria / Sofia, BulgariaPhone +359 2 973 71 81 - Fax +359 2 973 62 50

Donaldson Czech Republic / Klasterec - Czech Republic Phone +420 (0) 474319921 - Fax +420 (0) 474319930