ductile iron and cast iron check valves - · pdf file2 08.06 contents page figure number index...

8
08.06 Ductile Iron and Cast Iron Check Valves SECTION 4b Tel: +44 (0)1695 712800 Fax: +44 (0)1695 712820 Email: [email protected] [email protected] www.hattersley.com

Upload: buidat

Post on 02-Feb-2018

236 views

Category:

Documents


1 download

TRANSCRIPT

Page 1: Ductile Iron and Cast Iron Check Valves - · PDF file2 08.06 Contents Page Figure Number Index 2 Ductile Iron and Cast Iron Check Valves Introduction 3 Ductile Iron and Cast Iron Check

08.06

Ductile Iron and Cast IronCheck Valves

SECTION4b

Tel: +44 (0)1695 712800 Fax: +44 (0)1695 712820Email: [email protected]

[email protected]

Page 2: Ductile Iron and Cast Iron Check Valves - · PDF file2 08.06 Contents Page Figure Number Index 2 Ductile Iron and Cast Iron Check Valves Introduction 3 Ductile Iron and Cast Iron Check

2 08.06

Contents PageFigure Number Index 2Ductile Iron and Cast Iron Check Valves Introduction 3Ductile Iron and Cast Iron Check Valves Pressure/Temperature Chart 3Ductile Iron Check Valves Data Sheet 4Cast Iron Check Valves Data Sheets 5 - 8

Fig No Page

M650 PN25 4M651 PN16 5651 ANSI 5M653 PN16 6653 ANSI 6761 72761 7850 PN16 8850 PN25 8

In this catalogue we have endeavoured to make the information as accurate aspossible, but we cannot accept any responsibility should it be found that in anyrespect the information is inaccurate or incomplete or becomes so as result offurther developments.

Ductile Iron and Cast Iron Check Valves

Contents

Page 3: Ductile Iron and Cast Iron Check Valves - · PDF file2 08.06 Contents Page Figure Number Index 2 Ductile Iron and Cast Iron Check Valves Introduction 3 Ductile Iron and Cast Iron Check

308.06

Hattersley offer three basic types of check valves, namely Swing pattern,Wafer Twin Disk and AxialDisk pattern.When selecting check valves referenceto codes of practice and othermandatory specifications should bemade which may preclude certaintypes of valves for specific applications.

Swing PatternValve bodies are made from highgrade ductile or cast iron and haveintegral flanges. Seat rings arethreaded and securely fixed into the body.Swing check valves having 6 diametersof straight lengths of pipe upstreamand 3 diameters downstream aresuitable for velocities of up to 3metres per second. If the valve issituated such that turbulent flowenters the valve, the recommendedvelocity should not exceed 2 metresper second.Swing check valves are suitable forwater and other liquids.For air, gas and low pressureapplications especially where bubbletight closure is required a valve withrubber faced disk is required.

Wafer PatternA single piece cast iron body, housingtwin disks which are freely hinged ona transverse shaft.The elastomer seatis vulcanised to the body casting andis out of the fluid flow path ensuringextended seal life.

Axial Disk PatternSpring loaded axially guided disk withelastomer seal. Positive shut-off andnon-slam with streamlined flow andlow head loss. Flanged connections.WRc approved.

Introduction

Ductile Iron and Cast Iron Check Valves

StandardFig no PN Class End Size Range Pattern Trim

Rating Rating Connections MaterialM650PN25 25 Flanged 50 - 300mm Swing BronzeM651PN16 16 - Flanged 50 - 300mm Swing Bronze651ANSI - 125 Flanged 2 - 12in Swing BronzeM653PN16 16 - Flanged 50 - 300mm Swing Bronze653ANSI - 125 Flanged 2 - 12in Swing Bronze761 16 - Flanged 50 - 300mm Axial Guided Disk Bronze850 16 / 25 190 Wafer 50 - 600mm Twin Disk Bronze2761 16 - Flanged 50 - 400mm Double Check Bronze

Page 4: Ductile Iron and Cast Iron Check Valves - · PDF file2 08.06 Contents Page Figure Number Index 2 Ductile Iron and Cast Iron Check Valves Introduction 3 Ductile Iron and Cast Iron Check

08.064

Pressure/Temperature RatingBSEN 12334 PN2525 bar from -10 to 120ºC21.5 bar at 220ºC

Test Pressure (Hydraulic)PN25Shell: 37.5 barSeat: 27.5 bar

SpecificationBS EN 12334 PN25Horizontal swing patternBolted coverFlanged to BS EN 1092-2 PN25Copper alloy trimSuitable for mounting in horizontal and vertical pipelines (with verticalflow upwards).

0 40 80 120 160 200 240Temperature ˚C

28

24

20

16

12

4

0

Pre

ssur

e ba

r

8

Satura

ted

Ste

am

Fig. M650PN25

Ductile Iron Check Valves - Swing PatternPN25

Material Specification

Specification

Component Material BS EN

Cover Ductile Iron 1563 EN-JS 1050

Cover Gasket Asbestos Free

Hinge Pin Stainless Steel 970 420537

Hinge Ductile Iron 1563 EN-JS 1050

Disk Ductile Iron 1563 EN-JS 1050

Disk Face Ring Bronze 1982 CC491K

Body Ring Bronze 1982 CC491K

Body Ductile Iron 1563 EN-JS 1050

Dimensions

Nominal Size mm 50 65 80 100 125 150 200 250 300

A mm 203 216 241 292 330 356 495 622 699

B mm 121 135 141 168 182 215 267 305 343

Weight kg 16 22 28 40 62 82 144 232 310

A

B

Page 5: Ductile Iron and Cast Iron Check Valves - · PDF file2 08.06 Contents Page Figure Number Index 2 Ductile Iron and Cast Iron Check Valves Introduction 3 Ductile Iron and Cast Iron Check

Material Specification

Specification

Component Material BS EN

Cover Cast Iron 1561 EN-JL 1040

Cover Gasket Reinforced Compressed Graphite

Hinge Pin Brass 12164 CW603N

Hinge Pin Plug Brass 12164 CW603N

Hinge Ductile Iron 1563 EN-JS 1040

Disk Cast Iron 1561 EN-JL 1040

Disk Face Ring Bronze 1982 CC491K

Body Seat Ring Bronze 1982 CC491K

Body Cast Iron 1561 EN-JL 1040

Dimensions

Nominal Size mm 50 65 80 100 125 150 200 250 300

A mm 203 216 241 292 330 356 495 622 699

B mm 113 133 143 163 197 212 257 298 330

Weight kg 13 18 21 35 48 68 113 218 282

PN16

ANSI 125

0 40 80 120 160 200 240Temperature ˚C

18

16

14

12

10

8

6

4

2

0

Pre

ssur

e ba

r

Pressure/Temperature RatingBS EN 12334 PN1616 bar from -10 to 120ºC11.8 bar at 230ºC

BS EN 12334 ANSI 1259 bar at 218ºC13.8 bar from -10ºC to 66ºC

Test Pressure (Hydraulic)PN16Body: 24 barSeat: 17.6 bar

Test PressureClass 125Body: 24.1 barSeat: 13.8 bar

SpecificationBS EN 12334 PN16 & BS 5153 ANSIFace to face dimensions to;BS EN 558-1 Basic Series 10Cast iron bodyBolted coverCopper alloy trimSuitable for mounting in horizontal andvertical pipes (with the flow upwards)Flanged to BS EN 1092-2 PN16

08.06 5

Fig. M651PN16 - 651ANSI

Cast Iron Check Valves - Swing PatternPN16 - ANSI 125

A

B

Page 6: Ductile Iron and Cast Iron Check Valves - · PDF file2 08.06 Contents Page Figure Number Index 2 Ductile Iron and Cast Iron Check Valves Introduction 3 Ductile Iron and Cast Iron Check

PN16

ANSI 125

0 40 80 120 160 200 240Temperature ˚C

18

16

14

12

10

8

6

4

2

0

Pre

ssur

e ba

r

Fig. M653PN16 - 653ANSI

Cast Iron Check Valves with Lever and WeightPN16 - ANSI 125

08.066

Material Specification

Specification

Component Material BS EN

Cover Cast Iron 1561 EN-JL1040

Cover Gasket Asbestos Free

Hinge Pin Plug Stainless Steel 970 3045 15

Hinge Ductile Iron JS1050

Gland Packing Asbestos Free

Disk Cast Iron 1561 EN-JL1040

Disk Face Ring Bronze 1982 CC491K

Body Ring Bronze 1982 CC491K

Body Cast Iron 1561 EN-JL1040

Counter Weight Cast Iron 1561 EN-JL1040

Operating Shaft Stainless Steel 10088-1 X10CrNi18-10

Operating Lever Steel 970-050A20

Spring Stainless Steel 970-304S15

Dimensions

Nominal Size mm 50 65 80 100 125 150 200 250 300

A mm 203 216 241 292 330 356 495 622 699

B mm 121 135 141 168 182 215 267 305 343

C mm 200 200 215 250 300 290 580 730 720

Weight kg 21 27 33 45 66 86 152 244 320

Pressure/Temperature RatingBS EN 12334 PN1611.8 bar at 230ºC16 bar from -10 to 120ºCBS 5153 ANSI9 bar at 218ºC13.8 bar from -10 to 66ºC

Test Pressures (Hydraulic)PN16Shell: 24 barSeat: 17.6 barClass 125Shell: 24.1 barSeat: 13.8 bar

SpecificationBS EN 12334 PN16Bolted coverOutside lever and adjustable weightFlanged to BS EN 1092-2 PN16 andANSI B16.1 Class 125Copper alloy trimSuitable for mounting in horizontal andvertical pipelines (with vertical flowupwards)If valve fig number M653 is to be used in a vertical pipeline this must be stated on order so that the lever and weight assembly can be positioned accordingly.

A

B

C

Page 7: Ductile Iron and Cast Iron Check Valves - · PDF file2 08.06 Contents Page Figure Number Index 2 Ductile Iron and Cast Iron Check Valves Introduction 3 Ductile Iron and Cast Iron Check

08.06 7

Pressure/Temperature Rating16 bar from -10 to 85ºC

Test Pressure (Hydraulic)Body: 24 barSeat: 17.6 bar

SpecificationFig 761 WRAS Approved DN50 toDN300Spring Loaded axially guided diskResilient Seat located in bodyFlanged to BS EN 1092-2 PN16Alternative pressure ratings to PN25Alternative flange details includingBS EN 1092-2 PN25 and PN40 andANSI B16.1 Class 125.

Material Specification

Specification

Component Material BS EN ASTM

Body Ductile Iron 1563 EN-JS1030

Epoxy coated

Plunger DN50 -150 Bronze 1982 CC492K

DN200 - 400 Cast Iron - 1561 EN-JL1040 A126 ClB

Epoxy coated

Seat Retaining Ring Steel - Xylan coated

Seat Nitrile

Guide Bronze 1982 CC492K

Spring Stainless Steel 10088 X5CrNi18-10 A276 -304

Dimensions

Nom Size mm 50 65 80 100 125 150 200 250 300

A mm 120 119 130 155 200 230 280 344 385

B mm 240 241 260 310 403 460 560 688 770

D mm 165 185 200 220 250 285 340 405 460

Weight 761 kg 5 7 9 13 21 28 47 83 123

Weight 2761 kg 11 15 20 27 44 58 97 168 249

Fig. 761 and 2761

Aquacheck® Non Return ValvePN16

0 20 40 60 80 100Temperature ˚C

14

12

10

8

6

2

0

Pre

ssur

e ba

r

4

16

18

D

A

B

Double Check Valveconfiguration Fig 2761

Single Check ValveFig 761

Page 8: Ductile Iron and Cast Iron Check Valves - · PDF file2 08.06 Contents Page Figure Number Index 2 Ductile Iron and Cast Iron Check Valves Introduction 3 Ductile Iron and Cast Iron Check

08.068

Material Specification

Specification

Component Material BS EN ASTM

Body Cast Iron 1561 EN-JL 1040 A126 Cl B

Disks Bronze 1982 CC491K B62

Shaft Stainless Steel 10088-1 X10CrNi18-10 AISI 304

Stop Pin Stainless Steel 10088-1 X10CrNi18-10 AISI 304

Seat (850) EPDM

Seat (851) Nitrile

Springs Stainless Steel 10088-1 X10CrNi18-10 AISI 304

Dimensions 850PN16

Nominal Size mm 50 65 80 100 125 150 200 250 300 350 400

A mm 100 118 140 158 188 212 268 325 375 430 475

B mm 43 45 64 64 70 76 89 114 114 127 140

C mm 41 59 69 90 110 136 185 225 278 331 381

D mm 67 84 100 115 135 160 210 256 306 356 406

E mm 8 14 16 25 34 43 61 72 97 122 147

Weight kg 1.5 2 4 5 6 9 13 23 31 48 62

Note: Dimension C is minimum flange bore

0 20 40 60 80 100 120 140Temperature ˚C

14

12

10

8

6

2

0

Pre

ssur

e ba

r

4

16

18

EP

DM

Sea

t

Nitr

ile S

eat

Fig. 850PN16 - 850PN25

Cast Iron Check Valves - Wafer PatternPN16

Pressure/Temperature RatingEPDM16 bar up to 120ºC

Test Pressure (Hydraulic)Shell: 24 barSeat: 17.6 bar

SpecificationFace to face dimensions to BS EN 558-1Suitable for fitting between flanges to:BS EN 1092-2 PN10/16:ANSI B16.1 Class 125:BS10 Table D/E Suitable for mounting in horizontal andvertical pipelines (refer to installationinstructions)

E

B

A

DC

Dimensions 850PN25

Nominal Size mm 50 65 80 100 125 150 200

A mm 105 124 137 168 194 222 276

B mm 54 54 57 64 70 76 95

C mm 60 73 89 114 141 168 219

D mm 67 84 100 115 135 160 210

E mm 8 14 16 25 34 43 61

Weight kg 2.5 3.5 4.5 8.0 10.0 13.0 28.0

Note: Dimension C is minimum flange bore