Transcript
Page 1: CANTILEVER STACKER (E2CS/CM/CB) - Elevate Parking · E2CS 2300 1900 4000 2200 Hydraulic Small Cars E2CM 2500 2100 4500 2200 Hydrauli c Mid Siz ed Sedans E2CB 2500 2300 4500 2200 Hydrauli

This system is installed to park only one car on the platform and the ground level is left clear for vehicular movements. The system has column arrangement only on one side, generally on the boundary side, leaving the entire driveway clear for passage.

TYPE

Single Column Cantilever

Stacker

MODELS

E2CS/E2CM/E2CB

NO. OF CAR PER UNIT

1 Car

LIFTING CAPACITY

2000 Kg [ Car Weight]

LIFTING TIME

2 m/min

OPERATION

Hydraulic Power Pack, One Cylinder

with Key/Push

button operation.

POWER SUPPLY

415 V, 3 phase, 50 Hz

POWER CONSUMPTION

Up to 0.03 units per operation (approx.)

Specification Table:

MODEL

SYSTEM

PLATFORM

PLATFORM

LOWER CAR

LIFTING

CAR

WIDTH (MM)

WIDTH (MM)

LENGTH (MM)

HEIGHT(MAX)

MECHANISM

CATEGORY

E2CS

2300

1900

4000

2200

Hydraulic

Small Cars

E2CM 2500 2100 4500 2200 Hydraulic

Mid Sized Sedans

E2CB 2500 2300 4500 2200 Hydraulic Large Sedans/

SUV’s

Standard Features:

• Vehicles can be driven across stacks. • One Platform per system.

• Lifting mechanism installed only on one side of the Stack.

• Color scheme for the System will be provided as per the client’s color theme.

• Hot dipped Galvanized Corrugated floor plates to reduce dead weight and increase durability.

Compact Power pack system with

enclosed motors and rubber bush fittings for reduced noise levels.

Optional Photo sensor for the bottom car to prevent accidental lowering of upper stack.

Electromagnetic locking mechanism to prevent unwanted lowering of upper stack.

Limit switches to restrict the travel height by auto cutting off the motor.

Remote switch box with Key/Push button for easy operation.

Emergency Shutdown switch

Requirements from Client:

Parking area allotted must be cleared with no obstructions.

Additional space to be provided for storing and installing the Power Pack system.

While erection of the system client should provide storage facilities for keeping our tools and other valuable parts

of the system.

Temporary Electrical connection must be provided at the time of erection and installation of the systems.

12 Amps MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the

Main Power supply to the parking systems with 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E).

Incoming Cable Size should be at

least 4 Core x 2.5 sq.mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch to

Control Panel.

Civil work as foundation for Cantilever

parking system must be done at allotted area prior to installation

as per our Foundation drawing.

Foundation Concrete shall be of RCC and minimum M25 strength.

In case of Parking Installed

in open to Sky location, it is recommended to have a weather covering over the installation to

prevent damage to the electronics / mechanism due to weathering.

CANTILEVER STACKER (E2CS/CM/CB)

Note: All Sizes can be varied as per client requirements and site conditions.

L TP A R K I N G S Y S T E M S

Page 2: CANTILEVER STACKER (E2CS/CM/CB) - Elevate Parking · E2CS 2300 1900 4000 2200 Hydraulic Small Cars E2CM 2500 2100 4500 2200 Hydrauli c Mid Siz ed Sedans E2CB 2500 2300 4500 2200 Hydrauli

FOUR LEVEL STACK WITH TWO PIT LEVEL (E4BS(-2)/BM(-2)/BB(-2)) This system offer parking for Four cars with two above the ground level and Two cars in the Pit. For removing

the car parked on the first Pit level Ground level car must be removed

and for removing the

car in the second

Pit level both cars above the ground to be removed. Please Note

:-

Maximum height of the pit level depends upon the clear height above the ground level

Specification Table:

Standard Features:

Four

Platforms per system.

Color scheme for the System can

be provided as per the Client's requirement.

Hot dipped Galvanized Corrugated floor plates on platforms to reduce dead weight and increase durability.

Two sets of hydraulic cylinders will be provided.

Chain supported balancing and lifting Mechanism

Compact Power pack system with enclosed motor and rubber bush fittings for reduced noise levels.

Optional Photo sensor for the middle car to prevent accidental lowering of upper stack or lifting of the lower stack.

Electromagnetic locking mechanism to prevent unwanted lowering of upper stacks.

Limit switches to restrict the travel height by Auto cutting off the motor.

Remote switch box with Key/Push button for easy operation.

Emergency Shutdown switch.

Requirements from Client:

Parking area allotted must be cleared with no obstructions.

Civil work in Pit to be completed with appropriate drainage system provided to prevent water accumulation.

Base area

of the parking space allotted shall be Concrete with minimum strength of M20.

Pit area provided should be clean and free of any accumulated water.

Appropriate lighting to be provided within the pit and working area.

Additional space to be provided for storing and installing the Power Pack system.

While erection of the system client should provide storage facilities for keeping our tools and other valuable parts of the system.

Temporary Electrical connection must be provided at the time of erection and

installation of the systems.

12 amps MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the

Main Power supply to the parking systems with 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E).

• Incoming Cable Size should be at least 5 Core x 2.5 sq.mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch

to Control Panel.• In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the

installation to prevent damage to the electronics / mechanism due to weathering.

TYPE

MODELS

NO. OF CAR PER UNIT

LIFTING CAPACITY

LIFTING TIME

OPERATION

POWER SUPPLY

POWER CONSUMPTION

Four level Stack with Two pit level

E4BS(-2)/E4BM(-2)/E4BB(-2)

4 Cars

2000 Kg [ Per Car Weight]

2 m/min

(each stack)

Hydraulic Power Pack, Two Cylinderwith Key/Push

button operation.

415 V, 3 phase, 50 Hz

Up to 0.03 units per stack operation

(approx.)

MODEL

E3BS

E3BM

E3BB

SYSTEM DIMENSION

(MM)

2300 X 4500

2500 X 5500

ALL LEVEL

1900mm

ALL LEVEL2100mm

PLATFORM

MAXIMUM LIFTING

CAR

LENGTH (MM)

TRAVEL (MM) MECHANISM

CATEGORY

MAX -

4100mm

ALL LEVEL2100mm

Hydraulic

Small Cars

MAX – 5100mm

Hydraulic ALL LEVEL

2100mmSmall Cars/

Mid Sized Sedans

2800 X 5600 ALL LEVEL

2400MM

MAX – 5200mm ALL LEVEL

2100mmHydraulic

Mid Sized Sedan/

Small Cars/Large Sedans/

SUV’s

Note: All Sizes can be varied as per client requirements and site conditions for appropriate parking Spaces and Pit Dimensions.

L TP A R K I N G S Y S T E M S

PLATFORM

WIDTH

Page 3: CANTILEVER STACKER (E2CS/CM/CB) - Elevate Parking · E2CS 2300 1900 4000 2200 Hydraulic Small Cars E2CM 2500 2100 4500 2200 Hydrauli c Mid Siz ed Sedans E2CB 2500 2300 4500 2200 Hydrauli

L TP A R K I N G S Y S T E M S

PUZZLE PARKING SYSTEM WITH PIT (EXPS(-Y)/PM(-Y)/PB(-Y))

Note : X is the number of levels in the system above ground and Y is the levels in the Pit. Maximum usable length shall be total length minus 1400mm

TYPE Puzzle Parking with Pit

MODELS

NO. OF EMPTY SLOTS Number of Levels above ground Minus 1 (X-1)

LIFTING CAPACITY 2000 Kg [ Per Car Weight]

LIFTING TIME 1-2 minute per platform (variable)

SLIDING TIME 10 m/min per Platform

OPERATION

Upto 5 level Traction lifting, more than that Hydraulic Lifting, Lower Stack Sliding Eether Side With Motor Chain Mechanism. Integrated System with Touch Screen / Keyboard operation.

POWER SUPPLY 415 V, 3 phase, 50 Hz

POWER CONSUMPTION Up to 0.03 units per Stack Lifting and 0.01 units per sliding operation (approx).

Standard Features: • Fast and automatic retrieval of cars from the parking space without removing any cars parked on the ground level

of the system. • One slot left empty at each level to make way for the upper platform. • Hot dipped Galvanized Corrugated floor plates to reduce dead weight and increase durability. • Geared motor with minimum Safety factor of 2 with manual brake release. • Motor - Chain operated Sliding Mechanism. • Single Power Pack per system to reduce cost in case of hydraulic puzzle • Complete system monitored by PLC for smooth and error free automation. • Back up Limit switches provided for each slot for duplex safety. • Fabricated barriers provided on each platform to provide safety against unwanted lowering. • Fully automatic integrated operation. • Emergency Shut Down switch. • Optional Touch Screen/Numerical Keyboard operation Panel..

Requirement from Client: • Parking area allotted must be cleared with no obstructions.

• Civil work in Pit to be completed with appropriate drainage system provided to prevent water accumulation causing rusting of

the framing. • Pit area to be provided with adequate lighting.

• During erection of the system client should provide storage facilities for keeping our tools and other valuable parts

of the system. • Temporary Electrical connection must be provided at the time of erection and installation of the systems.

• 30 Amps ELCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided the from

Main Power supply to the parking systems. With 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E). • Incoming Cable Size should be at least 5 Core x 4sq. mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch to Control Panel.

• Civil work as foundation for parking system must be done at stack parking allotted area prior to Installation as per our drawings. • Base area of the parking space allotted shall be Concrete with minimum strength of M20.

• In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the installation to prevent damage to the electronics / mechanism due to weathering.

This is an automated system in which no car needs to be removed for removing other car parked on the system thus making each platform independent of the other. This system can be spread horizontally for upto 10 columns and vertically for upto 10 levels and upto Three levels in the pit. Number of slots that needs to be left empty = X-1 (where X is the number of levels).

EXPS(-Y)/EXPM(-Y)/EXPB(-Y)

Page 4: CANTILEVER STACKER (E2CS/CM/CB) - Elevate Parking · E2CS 2300 1900 4000 2200 Hydraulic Small Cars E2CM 2500 2100 4500 2200 Hydrauli c Mid Siz ed Sedans E2CB 2500 2300 4500 2200 Hydrauli

L TP A R K I N G S Y S T E M S

PUZZLE PARKING SYSTEM (EXPS/PM/PB)

Note : X is the number of levels in the system. Maximum usable length shall be total length minus 1400mm

TYPE Multi Level Puzzle Parking

MODELS EXPS/EXPM/EXPB

NO. OF EMPTY SLOTS Total number of levels minus one (X-1)

LIFTING CAPACITY 2000 Kg [ Per Car Weight]

LIFTING TIME 1.2 minutes per platform (variable)

SLIDING TIME 15 - 25 Seconds per Platform

OPERATION Upto 5 level Traction lifting, more than that Hydraulic Lifting, Lower Stack Sliding Eether Side With Motor Chain Mechanism. Integrated System with Touch Screen/ Keyboard operation.

POWER SUPPLY 415 V, 3 phase, 50 Hz

POWER CONSUMPTION Up to 0.05 units per Stack Lifting and 0.01 units per sliding operation (approx).

Standard Features: • Fast and automatic retrieval of cars from the parking Space without removing any cars parked on the ground level

of the system. • One Slot left empty at each level to make way for the upper platform to pass through. • Hot dipped Galvanized Corrugated floor plates to reduce dead weight and increase durability. • Geared motor with minimum Safety factor of 2 with manual brake release. • Motor- Chain operated Sliding Mechanism. • Single Power Pack per system to reduce cost in case of hydraulic puzzle • Complete system monitored by PLC for smooth and error free automation. • Back up Limit switches provided for each slot for duplex safety. • Fabricated barriers provided on each platform to provide safety against unwanted lowering. • Fully automatic integrated operation. • Emergency Shut Down switch. • Optional Touch Screen/Numerical Keyboard operation Panel.

Requirements from Client: • Parking area allotted must be cleared with no obstructions.

• While erection of the system client should provide storage facilities for keeping our tools and other valuable

parts of the system. • Temporary Electrical connection must be provided at the time of erection and installation of the systems.

• MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the Main Power

supply to the parking systems. With 3Ph 415V AC, 50Hz with Neutral and Earth(3Ph+N+E) as per our specifications. • Civil work as foundation for parking system must be done at stack parking allotted area prior to installation as per the

foundation plan submitted by us. • Base area of the parking space allotted shall be Concrete with minimum strength of M20.

• In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the installation to

prevent damage to the electronics / mechanism due to weathering.

This is an automated system in which no car needs to be removed for removing other car parked on the system thus making each platform independent of the other. This system can be spread horizontally for upto 10 columns and vertically for upto 10 levels. number of slots that needs to be left empty = X-1 (where X is the number of levels).

Page 5: CANTILEVER STACKER (E2CS/CM/CB) - Elevate Parking · E2CS 2300 1900 4000 2200 Hydraulic Small Cars E2CM 2500 2100 4500 2200 Hydrauli c Mid Siz ed Sedans E2CB 2500 2300 4500 2200 Hydrauli

THREE LEVEL SIMPLE STACKER (E3SS/SM/SB) This is Parking System offers parking for 3 cars; one on the ground and two on the two upper levels. The car

on the ground level will need to be removed before lowering the first level platform; similarly the ground and

first level cars will need to be removed before lowering the second level platform.

TYPE Three Level above Ground Stacker

MODELS E3SS/E3SM/E3SB

NO. OF CAR PER UNIT 3 Cars

LIFTING CAPACITY 2000 Kg [ Per Car Weight]

LIFTING TIME 2 m/min each stack

OPERATION Hydraulic Power Pack, One/Two Cylinder with Key/Push button operation.

POWER SUPPLY

415 V, 3 phase, 50 Hz

POWER CONSUMPTION Up to 0.04 units per stack operation (approx).

Specification Table:

MODEL

SYSTEM

PLATFORM

PLATFORM

LOWER CAR

LIFTING

CAR

DIMENS (MM)

WIDTH (MM)

LENGTH (MM)

HEIGHT(MAX)

MECHANISM

CATEGORY

2300 X 4500

ALL LEVEL

MAX – 2100 Small Cars

Level 2 – 1700

Level 1 – 1900 Gr.level –2000

2500 x 5500

Level 2 – 1900 Small Cars/

Level 1 – 2100 ALL LEVEL

MAX - 2100 Mid Sized Sedans

Gr.level –2200

Hydraulic /

Motorized

Level 2 – 2000 Mid Sized Sedan/

E3SS

E3SM

E3SB Small Cars/

Level 1 – 2200

Level 2 – 3700 Level 1 – 4000

Level 2 – 4000 Level 1 – 4500

ALL LEVEL MAX - 2100 Large Sedans/

Standard Features: • Two platforms per system. • Colour scheme for the System can be provided as per the client’s colour theme. • Hot dipped Galvanized Corrugated floor plates to reduce dead weight and increase durability.

• Chain supported balancing and lifting Mechanism. • Compact Power pack system with enclosed motor and rubber bush fittings for reduced noise levels.

• Optional Photo sensors for the middle and bottom car to prevent accidental lowering of upper stacks.

• Electromagnetic locking mechanism to prevent unwanted lowering of upper stacks.

• Limit switches to restrict the travel height by cutting of the motor.

• Remote switch box with Key/Push button for easy operation.

• Emergency Shutdown switch.

Requirements from Client: •

Parking area allotted must be cleared with no obstructions.

Additional space to be provided for storing and installing the Power Pack system.

One end of the stacker to be provided with a rigid support to prevent yawing of the stacker from top.

While erection of the system client should provide storage facilities for keeping our tools and other valuable parts of the system.

Temporary Electrical connection must be provided at the time of erection and installation of the systems.

12 amps MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the

Main Power supply to the parking systems. With 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E).

Incoming Cable Size should be at

least 5 Core x

2.5 sq.mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch to

Control Panel.

Civil work as foundation for stack parking system must be done at stack parking allotted area prior to installation.

Base area of the parking space allotted shall be Concrete with minimum strength of M20.

In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the installation to

prevent damage to the electronics / mechanism due to weathering. L TP A R K I N G S Y S T E M S

2700 x 5500Hydraulic / Motorized

Gr.level –2400

SUV’s

Note: All Sizes can be varied as per client requirements and site conditions.

Hydraulic /

Motorized

Level 2 – 4000 Level 1 – 4500

Page 6: CANTILEVER STACKER (E2CS/CM/CB) - Elevate Parking · E2CS 2300 1900 4000 2200 Hydraulic Small Cars E2CM 2500 2100 4500 2200 Hydrauli c Mid Siz ed Sedans E2CB 2500 2300 4500 2200 Hydrauli

THREE LEVEL STACK

WITH ONE PIT LEVEL (E3BS/BM/BB)

This system offer parking for three cars one on the ground level, one level above ground and one car in the

Pit. For removing the car parked on the first level or the Pit level, Ground level car must be removed.

Please Note

:-

Maximum height of the pit level depends upon the clear height above the ground level

Specification Table:

TYPE

Three level Stack

with one pit level

MODELS

E3BS/E3BM/E3BB

NO. OF CAR PER UNIT

3 Cars

LIFTING CAPACITY

2000 Kg [ Per Car Weight]

LIFTING TIME

2 m/min

(each stack)

OPERATION

Hydraulic Power Pack, Two Cylinder

with Key/Push

button operation.

POWER SUPPLY

415 V, 3 phase, 50 Hz

POWER CONSUMPTION

Up to 0.03 units per stack operation (approx.)

MODEL

SYSTEM DIMENSION

PLATFORM

PLATFORM

MAXIMUM

LIFTING

CAR

(MM) WIDTH (MM)

LENGTH (MM)

TRAVEL (MM)

MECHANISM CATEGORY

2300 X 4500

2500 X 5500

2700 X 5500

MAX - 4100

E3BS

Hydraulic

E3BM

MAX – 5100 Hydraulic

MAX – 5200 E3BB) Hydraulic

Note: All Sizes can be varied as per client requirements and site conditions for appropriate parking Spaces and Pit Dimension

Standard Features:

• Three Platforms per system.

• Color scheme for the System can

be provided as per the Client's requirement. • Hot dipped Galvanized Corrugated floor plates on platforms to reduce dead weight and increase durability.

• Two sets of hydraulic cylinders will be provided. • Chain supported balancing and lifting Mechanism

• Compact Power pack system with enclosed motor and rubber bush fittings for reduced noise levels. • Optional Photo sensor for the middle car to prevent accidental lowering of upper stack or lifting of the lower stack.

• Electromagnetic locking mechanism to prevent unwanted lowering of upper stacks.

• Limit switches to restrict the travel height by Auto cutting off the motor.

• Remote switch box with Key/Push button for easy operation.

• Emergency Shutdown switch.

Requirements from Client:

• Parking area allotted must be cleared with no obstructions.

• Civil work in Pit to be completed with appropriate drainage system provided to prevent water accumulation.

• Base area of the parking space allotted shall be Concrete with minimum strength of M20.

• Pit area provided should be clean and free of any accumulated water.

• Appropriate lighting to be provided within the pit and working area.

• Additional space to be provided for storing and installing the Power Pack system.

• While erection of the system client

should provide storage facilities for keeping our tools and other valuable parts of the system.

• Temporary Electrical connection must be provided at the time of erection and installation of the systems.

• 12 amps MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the

Main Power supply to the parking systems with 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E).

• Incoming Cable Size should be at

least 5 Core x 2.5 sq.mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch to Control Panel.

• In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the

installation to prevent damage to the electronics / mechanism due to weathering.

L TP A R K I N G S Y S T E M S

Small Cars

Small Cars/ Mid Sized Sedans

Mid Sized Sedan/

Small Cars/ Large Sedans/

SUV’s

ALL LEVEL 2000mm

ALL LEVEL2200mm

ALL LEVEL2400MM

ALL LEVEL2100mm

ALL LEVEL2100mm

ALL LEVEL2100mm

Page 7: CANTILEVER STACKER (E2CS/CM/CB) - Elevate Parking · E2CS 2300 1900 4000 2200 Hydraulic Small Cars E2CM 2500 2100 4500 2200 Hydrauli c Mid Siz ed Sedans E2CB 2500 2300 4500 2200 Hydrauli

TOWER PARKING SYSTEM (ETPS-X/TM-X/TB-X)

Note : X is the number of Cars in the system.

Maximum usable length shall be total length minus 1700 mm

TYPE

Motorized Tower parking System

MODELS

ETPS-X, ETPM-X, ETPB-X

NO. OF EMPTY SLOTS

Entire Centre Column left Empty

LIFTING CAPACITY

2500 Kg [ Per Car Weight]

LIFTING TIME Upto 60m per minute max (variable)

SLIDING TIME 15 -

25

Seconds per Platform

OPERATION

Down collective lifting mechanism with counter weight,

Sliding either Side with Motor Chain

Mechanism. Integrated System with Touch Screen/ Keyboard operation.

POWER SUPPLY

415 V, 3 phase, 50 Hz

POWER CONSUMPTION

Up to 0.07

units per Operation

and 0.01 units per sliding operation (approx).

Standard Features:

Requirements from Client:

Parking area allotted must be cleared with no obstructions.

While erection of the system client

should provide storage facilities for keeping our tools and other valuable

parts of the system.

Temporary Electrical connection must be provided at the time of erection and installation of the systems.

MCB and Main Electrical Connection (or 4 Pole RCBO)

along with electrical cable fitting must be provided from the Main Power

supply to the parking systems. With 3Ph 415V AC, 50Hz with Neutral and Earth(3Ph+N+E)

as per our specifications.

Civil work as foundation for stack parking system must be done at stack parking allotted area prior to installation

as per the foundation plan submitted by us.

If the system to be installed in the RCC shaft, hooks to be provided on the top as per our drawings.

In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the installation to

prevent damage to the electronics / mechanism due to weathering.

L TP A R K I N G S Y S T E M S

Tower parking is a system wherein upto 60 cars can be parked in a space of 3 cars. Having a lift working up and down in the centre transporting the vehicles to their designated slots vertically. This system can have 5 columns Horizontally and can go upto 30 levels high.

• Fast and automatic retrieval of cars from the parking Space without removing any cars parked on the ground level of the system.

• High speed Geared motors with counter weight and Guides for smooth lift and lowering.

• Turntable on the ground level for getting the car in the Drive out position

• Motor- Chain operated Sliding Mechanism.

• Complete system monitored by PLC for smooth and error free automation.

• Back up Limit switches provided for each slot for duplex safety.

• Robust Steel structure.

• Fully automatic integrated operation.

• Emergency Shut Down switch.

• Optional Touch Screen/Numerical Keyboard / RFID Swipe card operation Panel.

Page 8: CANTILEVER STACKER (E2CS/CM/CB) - Elevate Parking · E2CS 2300 1900 4000 2200 Hydraulic Small Cars E2CM 2500 2100 4500 2200 Hydrauli c Mid Siz ed Sedans E2CB 2500 2300 4500 2200 Hydrauli

TWO LEVEL SIMPLE STACKER (E2SS/SM/SB) This is a two level parking system, where one car is parked on the ground level and one on the platform. The car on the ground level will need to be removed for lowering and removing the car parked on the platform.

Specification Table:

Note: Sizes can be varied as per client requirements and site conditions.

Standard Features: • Hot dipped Galvanized Corrugated floor plates to reduce dead weight and increase durability. • Color scheme for the System will be provided as per the Client's requirement. • Compact Power pack system with enclosed motor and rubber bush fittings for reduced noise levels.

• Optional Photo sensor for the bottom car to prevent accidental lowering of upper stack. • Electromagnetic locking mechanism to prevent unwanted lowering of upper stack. • Limit

switches to restrict the travel height by auto cutting off the motor.

• Remote switch box with Key/Push button for easy operation.

• Emergency Shutdown switch.

Requirements from Client:

• Parking area allotted must be cleared with no obstructions.

During the erection of the system client should provide storage facilities for keeping our tools and other valuable parts of the system.

• Additional space to be provided for storing and installing the Power Pack system

Temporary Electrical connection must be provided at the time of erection and installation of the systems.

12 Amps MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the

Main Power supply to the parking systems. With 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E).

Incoming Cable Size should be at least

5 Core x 2.5 sq.mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch to Control Panel.

Civil work as foundation for stack parking system must be done at stack parking allotted area prior to installation.

Base area of the parking space allotted shall be Concrete with minimum strength of M20.

In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the

Installation to prevent damage to the electronics / mechanism due to weathering.

TYPE

MODELS

NO. OF CAR PER UNIT

LIFTING CAPACITY

LIFTING TIME

OPERATION

POWER SUPPLY

POWER CONSUMPTION

Two Level Single Stacker

E2SS/E2SM/E2SB

2 Cars

2000 Kg [ Car Weight]

2 m/min

Hydraulic Power Pack, One Cylinder with Key/Push Button Operation

415 V, 3 phase, 50 Hz

Up to 0.03 units per operation (approx.)

MODEL SYSTEM PLATFORM PLATFORM LOWER CAR LIFTING CAR

WIDTH (MM) WIDTH (MM) LENGTH (MM) HEIGHT(MAX) MECHANISM CATEGORY

E2SS

E2SM

E2SB

2300

2500

2700

2000

2200

2400

4000

4000

4500

2100

2100

2100

Hydraulic

Hydraulic

Hydraulic

Small Cars

Mid Sized Sedans

Large Sedans/SUV's

L TP A R K I N G S Y S T E M S

Page 9: CANTILEVER STACKER (E2CS/CM/CB) - Elevate Parking · E2CS 2300 1900 4000 2200 Hydraulic Small Cars E2CM 2500 2100 4500 2200 Hydrauli c Mid Siz ed Sedans E2CB 2500 2300 4500 2200 Hydrauli

THREE LEVEL STACK WITH TWO PIT LEVEL (E3BS(-2)/BM(-2)/BB(-2))

Specification Table:

Note: All Sizes can be varied as per client requirements and site conditions for appropriate parking Spaces and Pit Dimensions.

Standard Features:

• Three Platforms per system.

• Color scheme for the System can

be provided as per the Client's requirement.

• Hot dipped Galvanized Corrugated floor plates on platforms to reduce dead weight and increase durability.

• Two sets of hydraulic cylinders will be provided.

• Chain supported balancing and lifting Mechanism

• Compact Power pack system with enclosed motor and rubber bush fittings for reduced noise levels.

• Optional Photo sensor for the middle car to prevent accidental lifting of or lowering stack.

• Electromagnetic locking mechanism to prevent unwanted lowering of upper stacks.

• Limit switches to restrict the travel height by Auto cutting off the motor.

• Remote switch box with Key/Push button for easy operation.

• Emergency Shutdown switch.

Requirements from Client:

• Parking area allotted must be cleared with no obstructions.

• Civil work in Pit to be completed with appropriate drainage system provided to prevent water accumulation.

• Base area of the parking space allotted shall be Concrete with minimum strength of M20.

• Pit area provided should be clean and free of any accumulated water.

• Appropriate lighting to be provided within the pit and working area.

• Additional space to be provided for storing and installing the Power Pack system.

• While erection of the system client should provide storage facilities for keeping our tools and other valuable parts of the system.

• Temporary Electrical connection must be provided at the time of erection and installation of the systems.

• 12 amps MCB and Main Electrical Connection (or 4 Pole RCBO) along with electrical cable fitting must be provided from the

Main Power supply to the parking systems with 3Ph 415V AC, 50Hz with Neutral and Earth (3Ph+N+E).

• Incoming Cable Size should be at least 5 Core x 2.5 sq.mm. Flexible Copper multi Core cable (3PH+N+E) from Main Switch

to Control Panel.• In case of Parking Installed in open to Sky location, it is recommended to have a weather covering over the

installation to prevent damage to the electronics / mechanism due to weathering.

MODEL

SYSTEM DIMENSION

PLATFORM

PLATFORM

MAXIMUM

LIFTING

CAR

(MM) WIDTH (MM)

LENGTH (MM)

TRAVEL (MM)

MECHANISM CATEGORY

2300 X 4500

2500 X 5500

2700 X 5500

MAX - 4100

E3BS

Hydraulic

E3BM

MAX – 51 00 Hydraulic

MAX – 5200 E3BB) Hydraulic

Small Cars

Small Cars/ Mid Sized Sedans

Mid Sized Sedan/

Small Cars/ Large Sedans/

SUV’s

ALL LEVEL 2000mm

ALL LEVEL2200mm

ALL LEVEL2400MM

ALL LEVEL2100mm

ALL LEVEL2100mm

ALL LEVEL2100mm

TYPE Three level Stack with Two pit level

MODELS E3BS(-2)/E3BM(-2)/E3BB(-2)

NO. OF CAR PER UNIT 3 Cars

LIFTING CAPACITY

2000 Kg [ Per Car Weight]

LIFTING TIME

2 m/min

(each stack)

Hydraulic Power Pack, Two Cylinderwith Key/Push

button operation.

POWER SUPPLY

415 V, 3 phase, 50 Hz

POWER CONSUMPTION

Up to 0.03 units per stack operation

(approx.)

OPERATION

L TP A R K I N G S Y S T E M S

This system offer parking for three cars with one on the ground level and Two cars in the Pit. For removing the car parked on the first Pit level Ground level car must be removed and for removing the car in the second Pit level all cars above to be removed. Please Note :- Maximum height of the pit level depends upon the clear height above the ground level


Top Related