Download - Berechnung Gesamtwuchtguete en FR
-
8/19/2019 Berechnung Gesamtwuchtguete en FR
1/2
Effect of Imbalance · Influence du balourd
Technical Information · Information technique
285 w w w . s c h u n k . c o m
Effect of imbalance on spindles,Toolholders and toolsSpindle · Toolholder · Tool
Influence du balourd sur les broches,les porte-outils et les outilsBroche · Porte-outil · Outil
Illustration of balancing grade total
Illustration de la qualité d’équilibrage total
Example / ExempleExample / Exemple
Calculation of eccentricity
Calcul du balourd résiduel
Balancing grade conversion of the total system
Conversion de la qualité d’équilibrage du système
completU = U + U + U U = G · 60 · m2 · π · n
G = Uges. · 2 · π · n60 · mges.
tot.tot.
SpindleBroche
ToolholderPorte-outil
ToolOutil
tot. Broche Porte-outil Outil (G6.3)
USpindleBroche
= 0.4 · 60 · 15000 = 1.9102 · π · 30000
UToolholderPorte-outil
= 2.5 · 60 · 1125 = 0.8952 · π · 30000
UToolOutil
= 6.3 · 60 · 215 = 0.4312 · π · 30000
m in g U in gmm
mtot. in g: 16340tot.
Utot. in gmm: 3.236tot.
tot.tot.
G = 3.236 gmm · 2 ·π
·
30000 · min-1
= 0.6260 s · 16340 g
Broche - Qualité
d équilibrage des pièces en rotation
Porte outil
excentricité 2
Outil
excentricité 3
Qualité d équilibrage totale
Spindle with4-point tension
Broche avec
serrage 4 points
Hydraulic Expansion
Toolholder
Mandrin expansible
hydraulique
Countersink
Fraise de lamage
Sum of total systemSomme du système complet
2.25 gmm
2 µm
0.65 gmm
3 µm
Utot. = USpindle (G0.4) + UToolholder (G2.5) + UTool (G6.3)
-
8/19/2019 Berechnung Gesamtwuchtguete en FR
2/2
Effect of Imbalance · Influence du balourd
Technical Information · Information technique
Effect of imbalance on spindles,Toolholders and toolsSpindle · Toolholder · Tool
Quality levels of counterbalance for stiff balancing bodies (DIN ISO 1940-1).
Admissible unbalance with regard to the mass of the balancing body for different
quality levels G depending on the highest rotational speed of the balancing body.
Admissible unbalance/mass of the balancing body in gmm/kg (e in µm*)
* For stiff balancing bodies with two compensating levels, 50% of the standard
value are valid for each level. For stiff, disk shaped balancing bodies, the
whole standard value applies
Influence du balourd sur les broches,les porte-outils et les outilsBroche · Porte-outil · Outil
Exigences en matière de qualité dans l’équilibrage pour des corps rigides (DIN
ISO 1940-1). Balourd admissible en regard à la masse du corps d’équilibrage
pour divers niveaux de qualité G, en fonction de la vitesse de rotation maxima-
le du corps.
Balourd/masse admissible du corps d’équilibrage en gmm/kg (e en µm*)
* Pour les corps rigides avec deux plans de compensation, il convient de
prendre 50% de la valeur standard pour chaque plan. Pour les corps rigidescirculaires, il convient d’appliquer la valeur totale.
5 10 16 25 50 100 160 250 500 1000 1600
600 950 1500 3000 6000 9500 15000 30000 60000 95000300
1
G
G 5 . 2
6 1 G
3 . 6 G
G 4 . 0
Rest-imbalance
Balourd résiduel
in [gmm]
[min-1]
Speed in [rpm]
6380
504031.525201612.51086.3543.152.521.6
1.2510.80.630.50.40.3150.250.20.160.1250.10.08
0.0630.050.04 vitesse