digital camera/body/lens kit/double zoom lens kit model … · digital camera/body/lens kit/double...

ORDER NO. DSC1605004CEB26

Digital Camera/Body/Lens Kit/Double Zoom Lens KitModel No. DMC-GX80EB

DMC-GX80ECDMC-GX80EEDMC-GX80EFDMC-GX80EGDMC-GX80KEBDMC-GX80KECDMC-GX80KEEDMC-GX80KEFDMC-GX80KEGDMC-GX80WEBDMC-GX80WEFDMC-GX80WEGDMC-GX80CECDMC-GX80HECDMC-GX80HEFDMC-GX80HEGDMC-GX85PDMC-GX85PPDMC-GX85GCDMC-GX85GDDMC-GX85GHDMC-GX85GKDMC-GX85GN

© Panasonic Corporation 2016 Unauthorized copy-ing and distribution is a violation of law.

DMC-GX85GTDMC-GX85KPDMC-GX85KPPDMC-GX85KGCDMC-GX85KGD

DMC-GX85KGHDMC-GX85KGNDMC-GX85WGKDMC-GX85CGCDMC-GX85CGK

Colour[DMC-GX80/GX85](K)...........Black Type(S)...........Silver Type (except EE)(T)...........Brown Type (except EE/EF/P/PP/GN)[DMC-GX80K/GX85K](K)...........Black Type(S)...........Silver Type (except EE)(T)...........Brown Type (except EE/P/PP/GN)

[DMC-GX80W/GX85W/GX80C/GX85C](K)...........Black Type(S)...........Silver Type(T)...........Brown Type[DMC-GX80H](K)...........Black Type(S)...........Silver Type

DMC-GX80K/GX85K series: Interchangeable Lens (H-FS12032) is bundled.DMC-GX80W/GX85W series: Interchangeable Lens (H-FS12032/H-FS35100) are bundled.DMC-GX80C/GX85C series: Interchangeable Lens (H-H020A) is bundled.DMC-GX80H series: Interchangeable Lens (H-FS14140-KA) is bundled.

2

TABLE OF CONTENTSPAGE PAGE

1 Safety Precautions----------------------------------------------- 41.1. General Guidelines---------------------------------------- 41.2. Leakage Current Cold Check--------------------------- 41.3. Leakage Current Hot Check (See Figure. 1) ------- 41.4. How to Discharge the E.Capacitor on Flash

P.C.B. --------------------------------------------------------- 52 Warning -------------------------------------------------------------- 6

2.1. Prevention of Electrostatic Discharge (ESD)to Electrostatically Sensitive (ES) Devices---------- 6

2.2. How to Recycle the Lithium Ion Battery (U.S.Only) ---------------------------------------------------------- 6

2.3. How to Replace the Lithium Battery ------------------ 73 Service Navigation ----------------------------------------------- 8

3.1. Introduction-------------------------------------------------- 83.2. About service of bundled lenses----------------------- 83.3. Important Notice ------------------------------------------- 83.4. Service Notes----------------------------------------------143.5. General Description About Lead Free Solder

(PbF)---------------------------------------------------------163.6. How to Define the Model Suffix (NTSC or PAL

Model) -------------------------------------------------------174 Specifications ----------------------------------------------------22

4.1. Camera Body----------------------------------------------224.2. Lens----------------------------------------------------------25

5 Location of Controls and Components ------------------275.1. Camera Body----------------------------------------------275.2. Lens----------------------------------------------------------28

6 Service Mode -----------------------------------------------------296.1. Error Code Memory Function--------------------------29

7 Troubleshooting Guide ----------------------------------------317.1. Checking Method of Body and

Interchangeable Lens -----------------------------------317.2. Wi-Fi Circuit ------------------------------------------------35

8 Service Fixture & Tools----------------------------------------368.1. Service Fixture and Tools-------------------------------368.2. Clean Box --------------------------------------------------388.3. When Replacing the Main P.C.B.---------------------388.4. Service Position-------------------------------------------39

9 Disassembly and Assembly Instructions ---------------409.1. Camera Body Part----------------------------------------409.2. Disassembly and Assembly Procedure for the

Lens----------------------------------------------------------5210 Measurements and Adjustments---------------------------53

10.1. Matrix Chart for Replaced Part and NecessaryAdjustment -------------------------------------------------53

11 Maintenance-------------------------------------------------------5611.1. Notice in External Cleaning ----------------------------56

12 Block Diagram----------------------------------------------------5712.1. Overall Block Diagram ----------------------------------5712.2. System Control Block Diagram -----------------------5812.3. Video/Audio Process(1) Block Diagram ------------5912.4. Video/Audio Process(2) Block Diagram ------------6012.5. Gyro/WiFi Block Diagram-------------------------------6112.6. Flash/Hot Shoe Block Diagram -----------------------6212.7. Lens Block Diagram -------------------------------------6312.8. Power(1) Block Diagram--------------------------------6412.9. Power(2) Block Diagram--------------------------------65

12.10. Power(3) Block Diagram--------------------------------66

13 Wiring Connection Diagram--------------------------------- 6713.1. Interconnection Diagram ------------------------------- 67

14 Schematic Diagram -------------------------------------------- 6815 Printed Circuit Board ------------------------------------------ 6816 Exploded View and Replacement Parts List ----------- 68

3

1 Safety Precautions1.1. General Guidelines

1. IMPORTANT SAFETY NOTICEThere are special components used in this equipmentwhich are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout,Exploded Views and Replacement Parts List. It is essen-tial that these critical parts should be replaced with manu-facturer’s specified parts to prevent X-RADIATION,shock, fire, or other hazards. Do not modify the originaldesign without permission of manufacturer.

2. An Isolation Transformer should always be used duringthe servicing of AC Adaptor whose chassis is not isolatedfrom the AC power line. Use a transformer of adequatepower rating as this protects the technician from acci-dents resulting in personal injury from electrical shocks. Itwill also protect AC Adaptor from being damaged by acci-dental shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a shortcircuit is found, replace all parts which have been over-heated or damaged by the short circuit.

4. After servicing, see to it that all the protective devicessuch as insulation barriers, insulation papers shields areproperly installed.

5. After servicing, make the following leakage currentchecks to prevent the customer from being exposed toshock hazards.

1.2. Leakage Current Cold Check1. Unplug the AC cord and connect a jumper between the

two prongs on the plug.2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed metal-lic cabinet part on the equipment such as screwheads,connectors, control shafts, etc. When the exposed metal-lic part has a return path to the chassis, the readingshould be between 1 MΩ and 5.2 MΩ. When the exposedmetal does not have a return path to the chassis, thereading must be infinity.

1.3. Leakage Current Hot Check(See Figure. 1)

1. Plug the AC cord directly into the AC outlet. Do not usean isolation transformer for this check.

2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μFcapacitor, between each exposed metallic part on the setand a good earth ground, as shown in Figure. 1.

3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, tomeasure the potential across the resistor.

4. Check each exposed metallic part, and measure the volt-age at each point.

5. Reverse the AC plug in the AC outlet and repeat each ofthe above measurements.

6. The potential at any point should not exceed 0.75 V RMS.A leakage current tester (Simpson Model 229 or equiva-lent) may be used to make the hot checks, leakage cur-rent must not exceed 1/2 mA. In case a measurement isoutside of the limits specified, there is a possibility of ashock hazard, and the equipment should be repaired andrechecked before it is returned to the customer.

Figure. 1

4

1.4. How to Discharge the E.Capacitor on Flash P.C.B.CAUTION:

• Be sure to discharge the E.Capacitor on Flash P.C.B. before disassembling.• Be careful of the high voltage circuit on Flash P.C.B. when servicing.

[Discharging Procedure]1. Remove the Top Case Unit.2. Put the insulation tube on the lead part of resistor (ERG5SJ102: 1kΩ / 5W).

(An equivalent type of resistor may be used.)3. Put the resistor between both terminals of E.Capacitor on the Flash P.C.B. for approx. 5 seconds.4. After discharging, confirm that the E.Capacitor voltage is lower than 10V by using a voltmeter.

5

2 Warning2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically

Sensitive (ES) DevicesSome semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-trostatically Sensitive (ES) Devices.

The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge(ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on yourbody by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-num foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an antistatic solder removal device. Some solder removal devices not classified as “antistatic (ESD protected)” can

generate electrical charge sufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-ble conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective materialto the chassis or circuit assembly into which the device will be installed.CAUTION :

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-ficient to damage an ES device).

2.2. How to Recycle the Lithium Ion Battery (U.S. Only)

6

2.3. How to Replace the Lithium Battery2.3.1. Replacement Procedure

1. Remove the TOP P.C.B.. (Refer to Disassembly Procedures.)2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. “B7001” at component side of TOP

P.C.B.) and remove the Lithium battery together with electric lead terminal. Then replace it into new one.NOTE:

The Lithium battery includes electric lead terminals.

NOTE:This Lithium battery is a critical component.It must never be subjected to excessive heat or discharge.It must therefore only be fitted in requirement designed specifically for its use.Replacement batteries must be of same type and manufacture.They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.Do not attempt to re-charge the old battery or re-use it for any other purpose.It should be disposed of in waste products destined for burial rather than incineration.

NOTE:Above caution is applicable for a battery pack which is for DMC-GX80/GX85/GX80K/GX85K/GX80W/GX85W/GX80C/GX85C/GX80H series, as well.

7

3 Service Navigation3.1. IntroductionThis service manual contains technical information, which allow service personnel’s to understand and service this model.Please place orders using the parts list and not the drawing reference numbers.If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.

3.2. About service of bundled lensesPlease refer to the following service manuals about Disassembly and Assembly or Maintenance of bundled lenses.

• H-FS12032PP/E/GK: Order No.DSC1311036CE• H-FS35100PP/E/GK: Order No.DSC1410024CE• H-H020APP/E/GK: Order No.DSC1307028CE• H-FS14140PP/E/GK: Order No.DSC1305023CE/DSC1506509SE

3.3. Important Notice*When servicing, it is recommended dealing with Clean box. (Refer to “8.2. Clean Box” section of this service manual for details.)

3.3.1. Camera Body Unit3.3.1.1. About Flange back adjustmentWhen turning the image sensor unit mounting screw even a little or removing, the “simplicity flange back adjustment” is need.Perform the “simplicity flange back adjustment” according to contents described in “10 Measurement and Adjustment” section ofthis service manual.

3.3.1.2. About Shutter Unit (Ref. 80)Before exchanging the “shutter unit”, confirm that the symptom and/or phenomenon is not due to the setting of functions.Important:

After replacing the shutter unit, the shutter unit data has to be stored to the unit.The shutter unit supplied as service parts has affix the label of own configure data.By inputting second line to fourth line of these data into the adjustment software and writing these data to Flash-ROM (IC6003),the shutter adjustment becomes needless.In addition, the adjustment software can read data encoded to QR Code by using WEB camera with a close-up function.Refer to the adjustment instruction in the adjustment software for details.

8

3.3.1.3. About Main P.C.B. (Ref.1) & Flash-ROM (IC6003)Before exchanging the “Main P.C.B.”, confirm that the symptom and/or phenomenon is not due to the setting of functions.Important:

When cannot be repaired in the IC exchange, and in the case of performing the “Main P.C.B.” exchange, carry out any of following.In the case of exchanging the Flash-ROM (IC6003) is same way too.1. When the camera power can be ON, and camera body and adjustment software can be communicated:

Before replacing the “Main P.C.B. and/or Flash-ROM”, proceed the EEPROM data backup from the unit.After replacing the Main P.C.B. and/or Flash-ROM, overwrite the EEPROM data with backup data from the unit first, then proceed the adjustment /inspection. (Almost adjustment/inspection items can be omitted.)Refer to the adjustment instruction in the adjustment software for details.

2. When the camera power cannot be ON, or camera body and adjustment software cannot be communicated:Almost full adjustment/inspection must be performed after replacing the “Main P.C.B. and/or Flash-ROM”.Refer to the adjustment instruction in the adjustment software for details.

Notes after replacement:Make sure the camera body firmware is latest version.

3.3.1.4. About Venus Engine (IC6001) [Located on the Main P.C.B.]:• The Venus Engine (IC6001) consists of two IC chips, which are fixed together with solder.

(The so called, “Package On Package” type IC.)NOTE:

• During servicing, do not press down hard on the surface of IC6001.

9

3.3.2. Lens Unit (Interchangeable Lens: H-FS12032)3.3.2.1. About Lens Main Unit (Ref. 203)

1. Lens Main Unit (Ref. 203) is not supplied due to difficulty of the transportation issue (Fragile, Dust-free packing), and requirescritical lens adjustments.Therefore, any needs of the “Lens Main Unit” (Ref. 203), carefully confirm its performance in advance.

2. Once “Lens Main Unit” (Ref. 203) is confirmed as defective, place order “Lens Unit” (Ref. 200) and replace Shading Frame(Ref. 208), to maintain Serial number of owner’s original lens.

10



2. Once “Lens Main Unit” (Ref. 409) is confirmed as defective, place order “Lens Unit” (Ref. 400) and replace Shading Frame(Ref. 402), to maintain Serial number of owner's original lens.

11

3.3.4. Lens Unit (Interchangeable Lens: H-H020A)3.3.4.1. About Lens Main Unit (Ref. 515)


2. Once “Lens Main Unit” (Ref. 515) is confirmed as defective, place order “Lens Unit” (Ref. 500) and replace Shading Frame(Ref. 503), to maintain Serial number of owner's original lens.

12



2. Once “Lens Main Unit” (Ref. 609) is confirmed as defective, place order “Lens Unit” (Ref. 600) and replace Rear Frame Unit(Ref. 608), to maintain Serial number of owner’s original lens.

3.3.6. About Flexible Cable and ConnectorDo not touch carelessly so that the foreign body should not adhere to the terminal part of flexible cable and connector.Wipe off with a clean cloth and the cotton bud, etc. when the terminal part is dirty.

13

3.4. Service Notes3.4.1. About Wi-Fi FunctionThe page number in this chapter does not show the page number of this service manual.

14

3.4.2. Important Notice of ServicingThis camera unit has the personal information of wireless LAN connection the customer has registered.For the protection of private information, please erase the personal information after the completion of repair by “Initial Settings”.In addition, please print out the following documents, and pass to the customer with the camera unit.

Printing Material [Leaflet for Customer]

[For The Customer]

Before using your camera please check the Wi-Fi settings.Depending on what was serviced, the settings may have been reset to the factory defaults.

1. If the settings were reset you will need to reenter your Lumix Club login ID and password.

If you have forgotten the login ID and/or Password, please connect to the Lumix Club website and create a new ones.

2.You may also have to reenter the settings for your local Wi-Fi network settings.

We recommend consulting the operating manual if you have any questions.

15

3.5. General Description About Lead Free Solder (PbF)The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for thisequipment in considering the globally environmental conservation.The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin(Sn), silver (Ag) and copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of thenormal solder.Distinction of P.C.B. Lead Free Solder being used

Service caution for repair work using Lead Free Solder (PbF)• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.

(Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)• To put lead free solder, it should be well molten and mixed with the original lead free solder.• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the

lead free solder.• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C

(662±86°F).Recommended Lead Free Solder (Service Parts Route.)

• The following 3 types of lead free solder are available through the service parts route.SVKZ000001-----------(0.3mm 100g Reel)SVKZ000002-----------(0.6mm 100g Reel)SVKZ000003-----------(1.0mm 100g Reel)

Note* Ingredient: Tin (Sn) 96.5%, Silver (Ag) 3.0%, Copper (Cu) 0.5%. (Flux cored)

16

3.6. How to Define the Model Suffix (NTSC or PAL Model)There are nine kinds of DMC-GX7MK2/GX80/GX85 (Camera body unit), regardless of the colours.

• a) DMC-GX7MK2 (Japan domestic model)• b) DMC-GX85P/PP• c) DMC-GX80EB/EC/EF/EG• d) DMC-GX80EE• e) DMC-GX85GN• f) DMC-GX85GD• g) DMC-GX85GT• h) DMC-GX85GK• i) DMC-GX85GC/GH

What is the difference is that the “Initial Settings” data which is stored in Flash-ROM mounted on Main P.C.B..

3.6.1. Defining Methods:To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the unit.

NOTE:After replacing the Main P.C.B., be sure to achieve adjustment.Refer to the adjustment instruction in the adjustment software for details.

17

3.6.2. Initial Settings:After replacing the Main P.C.B. and/or Flash-ROM, make sure to perform the initial settings after achieving the adjustment by order-ing the following procedure in accordance with model suffix of the unit.1. Important Notice:

Before proceeding Initial settings, make sure to read the following CAUTION.

2. Procedures:• Precautions: Read the above “CAUTION” carefully.• Preparation:

Attach the fully charged Battery, and insert the memory card.Confirm that it is not intelligent auto mode [ iA ] or intelligent auto plus mode [ iA+ ].(If the unit is intelligent auto mode [ iA ] or intelligent auto plus mode [ iA+ ], it does not display the initial setting menu.)

• Step 1. The temporary cancellation of “Initial Settings”:While pressing [ Playback ] button, [ AF/AE LOCK ] button and “[ RIGHT ] of Cursor buttons” simultaneously, turn the Power on.

• Step 2. The cancellation of “Initial Settings”:Press the [ Playback ] button in order to enter the [ Playback ] mode.Press [ AF/AE LOCK ] button and “[ UP ] of Cursor buttons” simultaneously, then turn the power off.

The LCD displays the “ ! ” mark before the unit powers down.

• Step 3. Turn the Power On:Set the mode dial to [ P ] (Program AE Mode), then turn the power on.

18

• Step 4. Display the Initial Settings:While pressing [ MENU/SET ] button and “[ RIGHT ] of Cursor buttons” simultaneously, turn the power off. The “Initial Settings” menu is displayed.There are two kinds of “Initial Settings” menu form as follows:[ CASE 1. After replacing the Main P.C.B. and/or Flash-ROM ][ Except “EB/EC/EF and EG” models : SEP0697AA is used as a Main P.C.B. ]When Main P.C.B. has just been replaced, 11 model suffixes are displayed as follows. (three pages in total)

[Only “EB/EC/EF and EG” models : (SEP0697AB is used as a Main P.C.B.)]When Main P.C.B. has just been replaced, only 4 model suffixes are displayed as follows. (one page in total)(Do not select GC.)

[CASE 2. Other than “After replacing the Main P.C.B. and/or Flash-ROM”]

19

• Step 5. Cancel “Strict” mode:Press the [ DISP. ] button to cancel “Strict” mode. (Confirm the “Strict” is disappeared.)

• Step 6. Choose the Model Suffix in “Initial Settings”: (Refer to “CAUTION”)[Caution: After replacing the Main P.C.B. and/or Flash-ROM]

The model suffix can been chosen, JUST ONE TIME.Once one of the model suffix have been chosen, the model suffix lists will not be displayed, thus, it can not be changed.Therefore, select the area carefully.

Select the area with pressing “[ UP ] / [ DOWN ] of Cursor buttons”.

• Step 7. Set the Model Suffix in “Initial Settings”:Press the “[ RIGHT ] of Cursor buttons”.The only set area is displayed, and then press the “[ RIGHT ] of Cursor buttons” after confirmation.(The unit is powered off automatically.)

NOTE:When the error message such as the following is displayed, cancel “Strict” mode.Press [ DISP. ] button to clear the “Strict” display at the upper right corner of screen.

20

• Step 8. Confirmation:Confirm the display of “PLEASE SET THE CLOCK” in concerned language when the unit is turned on again.When the unit is connected to PC with USB cable, it is detected as removable media.(When the “GK” or “GT” model suffix is selected, the display shows “PLEASE SET THE CLOCK” in Chinese.)

As for your reference, major default setting condition is as shown in the following table.• Default setting (After “Initial Settings”)

MODEL VIDEO OUTPUT LANGUAGE DATE REMARKSa) DMC-GX85P NTSC English Month/Date/Yearb) DMC-GX85PP NTSC English Month/Date/Yearc) DMC-GX80EB PAL English Date/Month/Yeard) DMC-GX80EC PAL English Date/Month/Yeare) DMC-GX80EE PAL Russian Date/Month/Yearf) DMC-GX80EF PAL English Date/Month/Yearg) DMC-GX80EG PAL English Date/Month/Yearh) DMC-GX85GC PAL English Date/Month/Yeari) DMC-GX85GD NTSC Korean Year/Month/Datej) DMC-GX85GH PAL English Date/Month/Yeark) DMC-GX85GK PAL Chinese (simplified) Year/Month/Datel) DMC-GX85GN PAL English Date/Month/Year

m) DMC-GX85GT NTSC Chinese (traditional) Year/Month/Daten) DMC-GX7MK2JPC (Japan domestic model) NTSC/PAL NTSC/PAL Japanese/

Chinese (simplified)Year/Month/Date

21

4 Specifications4.1. Camera BodyThe following specification is based on DMC-GX80K/DMC-GX80C/DMC-GX80H/DMC-GX80W/DMC-GX80EB.Some specifications may differ depending on model suffix.

22

4.2. Lens

25

5 Location of Controls and ComponentsThe following description is for DMC-GX80K/DMC-GX80C/DMC-GX80H/DMC-GX80W/DMC-GX80EB.Some descriptions may differ depending on model suffix.The page number in this chapter does not show the page number of this service manual.

5.1. Camera Body

27

5.2. Lens

28

6 Service Mode6.1. Error Code Memory Function

1. General DescriptionThis unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from thelatest. When the error is occurred more than 16, the oldest error is overwritten in sequence.The error code is not memorized when the power supply is shut down forcibly.(i.e., when the unit is powered on by the battery, the battery is pulled out)The error code is memorized to Flash-ROM when the unit has just before powered off.

2. How to DisplayThe error code can be displayed by ordering the following procedure:

• PreparationAttach the fully charged Battery, and insert the memory card.

• Step 1. The temporary cancellation of “Initial Settings”:While pressing [ Playback ] button, [ AF/AE LOCK ] button and “[ RIGHT ] of Cursor buttons” simultaneously, turn the Poweron.

• Step 2. Execute the error code display mode:Press [ MENU/SET ] button, [ AF/AE LOCK ] button and “[ LEFT ] of Cursor buttons” simultaneously with the step 1 condi-tion.The display is changed as shown below when the above buttons are pressed simultaneously.Normal display → Error code display → Camera information display → Normal display → .....

Example of Error Code Display

29

Error Code ListThe error code consists of 8 bit data and it shows the following information.

Important Notice about “Error Code List”About “*” indication:The third digit from the left is different as follows.

- In case of 0 (example: 2B001000)When the third digit from the left shows “0”, this error occurred under the condition of Initial Settings has been completed.It means that this error is occurred basically at user side.

- In case of 8 (example: 2B801000)When the third digit from the left shows “8”, this error occurred under the condition of Initial Settings has been released.(Example; Factory assembling-line before unit shipment, Service mode etc.)It means that this error is occurred at service side.

• Step 3. How to Exit from Error Code Display Mode:Simply, turn the power off. (Since Error Code display mode is executed under the condition of temporary cancellation of “Initial Settings”, it wake up with normal condition when turn off the power.)NOTE:

The error code can not be initialized.

30

7 Troubleshooting Guide7.1. Checking Method of Body and Interchangeable Lens

1. Initial (Default) Status Of The Lens UnitThe Lens unit which is supplied as a standard accessory for this camera unit (H-H020A, H-FS12032, H-FS14140, H-FS35100) shows the following status when the Lens is detached from the Camera unit.NOTE: Although the lens unit is attached it shows the same condition when the Camera turns off.

H-H020A (Included in DMC-GX80C/GX85C):a. FOCUS RING

The Focus condition does not changed although Focus ring is rotated. (Free rotation.)

H-FS12032 (Included in DMC-GX80K/GX85K, DMC-GX80W/GX85W):a. ZOOM RING

When the Zoom ring is rotated, Zoom condition is changing accordingly. (The 1st lens frame moves.)[ Focal length : 12mm to 32mm [ 35mm film camera equivalent: 24mm to 64mm ] ]

b. FOCUS RINGThe Focus condition does not changed although Focus ring is rotated. (Free rotation.)

H-FS14140 (Included in DMC-GX80H/GX85H):a. ZOOM RING

When the Zoom ring is rotated, Zoom condition is changing accordingly. (The 1st lens frame moves.) [ Focal length : 14mm to 140mm [ 35mm film camera equivalent: 28mm to 280mm ] ]


H-FS35100 (Included in DMC-GX80C/GX85C):a. ZOOM RING

When the Zoom ring is rotated, Zoom condition is changing accordingly. (The 1st lens frame moves.) [ Focal length : 35mm to 100mm [ 35mm film camera equivalent: 70mm to 200mm ] ]


2. Initial Inspection Tips (Before Determine The Unit Being Faulty/Defective):Since this unit is equipped with various functions/settings, some phenomenon/effect might be caused by miss usage of func-tion and/or settings.It might be made a miss-judgement caused by miss usage of function & settings although the unit is working properly withoutfault.Therefore, check/confirm the followings before concluding/determine the unit being faulty/defective.NOTE: Refer to the Operating Instructions about content of various settings. Also, useful hint/tips for this unit is available at following URL, and is updated frequently. http://panasonic.jp/support/global/cs/dsc/

If it is hard to determine whether the resolution is out of specification or not, proceed the “RESOLUTION INSPECTION”,before replacing the Lens Main Unit. (The unit might be mishandling, dropping or others.)

31

3. Reference information

32

7.2. Wi-Fi Circuit7.2.1. How to Remove Wi-Fi Password ProtectionTo prevent incorrect operation or use of the Wi-Fi function by a third party and to protect saved personal information, this unit pro-tects the Wi-Fi function with a password.It is unable to service with password locked condition. When accepting for repair, the unit has been set the Wi-Fi password by cus-tomer, run the [ Reset Wi-Fi Settings ] for removing Wi-Fi password, then check the operation.

[Reset Procedure of Wi-Fi Settings]1) Press the [ MENU/SET ] button, and select the [ SETUP ] mode by Cursor buttons. Select [ Reset Wi-Fi Settings ] by Cursor buttons, then press the [ MENU/SET ] button.2) Select [ YES ] and press the [ MENU/SET ] button.

(The [ Reset Wi-Fi Settings ] performs not only resetting Wi-Fi Password but also resetting other all Wi-Fi Settings.)

7.2.2. Checking of trouble caused by Wi-Fi Circuit or not

35

8 Service Fixture & Tools8.1. Service Fixture and ToolsThe following service fixture and tools are used for checking and servicing this unit.

36

About Adjustment Shaft:• VMS7941 for H-H020A

37

8.2. Clean Box• The repair quality is considered, and it is recommended working in the environment of specified clean level less than class

10,000 (Federal Standard 209D). [NOTE]

• Work in the environment of specified clean level less than class 10,000 (Federal Standard 209D) when inside cleaning of a lens.Please refer to the following service manuals.


8.3. When Replacing the Main P.C.B.After replacing the Main P.C.B., be sure to achieve adjustment.Refer to the adjustment instruction in the adjustment software for details.

38

8.4. Service PositionThis service position is used for checking and replacing parts. Use the following extension cables for servicing.

No. Parts No. Connection From1 RFKZ0466 FP9005(MAIN P.C.B.) ←→ FP8101(BATTERY P.C.B.) 29pin / 0.3 FFC2 RFKZ0466 FP8102(BATTERY P.C.B.) ←→ FLASH UNIT 29pin / 0.3 FFC3 VFK1978 FP9006(MAIN P.C.B.) ←→ FRONT CASE UNIT 31pin / 0.3 FFC4 RFKZ0626 FP9004(MAIN P.C.B.) ←→ MOUNT BASE UNIT 21pin / 0.3 FFC5 VFK1950 FP9302(SUB P.C.B.) ←→LVF UNIT 33pin / 0.3 FFC6 VFK1480 FP9403(SUB P.C.B.) ←→ LVF UNIT 6pin / 0.5 FFC7 VFK1951 FP9301(SUB P.C.B.) ←→ LCD UNIT 39pin / 0.3 FFC

39

9 Disassembly and Assembly Instructions9.1. Camera Body Part9.1.1. Disassembly Flow ChartThis is a disassembling chart.When assembling, perform this chart conversely.

9.1.2. P.C.B. Location

40

9.1.3. Disassembly Procedure

No. Item Fig. Removal1 Rear Case Unit (Fig. D1) Screw (A) x 1

Screw (B) x 2Screw (C) x 2

(Fig. D2) Hot Shoe CoverShoe SpringScrew (D) x 2Screw (E) x 1

(Fig. D3) Locking tab x 1FP9301 (Flex)FP9007 (Flex)Rear Case Unit

2 Rear Plate Unit,LCD Unit

(Fig. D4) Screw (F) x 4FPC TapeLCD FPC Tape ASolder (2 points)Screw (G) x 6Screw (H) x 3Rear Plate AngleConvex x 7LCD Lock PieceLCD Lock SpringAE Lock ButtonSpeakerRear Plate Unit

(Fig. D5) LCD Unit3 Top Case Unit (Fig. D6) FP9003 (Flex)

FP9302 (Flex)FP9403 (Flex)Screw (I) x 2Screw (J) x 1

(Fig. D7) Locking tab x 3FP8102 (Flex)Top Case Unit

4 Main P.C.B.,Sub P.C.B.

(Fig. D8) FPC TapeFP3501 (Flex)FP3502 (Flex)FP9004 (Flex)FP9005 (Flex)FP9006 (Flex)FP9401 (Flex)FP9402 (Flex)FP9404 (Flex)FP9901 (Flex)Screw (K) x 1Screw (L) x 3Convex x 3Convex x 1Battery Earth PlateMain P.C.B.Sub P.C.B.

5 Image Sensor Unit,Shutter Unit

(Fig. D9) Screw (M) x 3Spring x 3Image Sensor Unit

(Fig. D10) Screw (N) x 1Screw (O) x 2Damper O RingShutter Unit

6 Mount,Lens Ring,Mount Base Unit

(Fig. D11) Screw (P) x 2Screw (Q) x 2MountConvex x 1Mount SpringScrew (R) x 5Lens RingConvex x 2Front Shoe Plate

(Fig. D12) Locking tab x 2Screw (S) x 1Capacitor HolderScrew (T) x 2

(Fig. D13) Lens Lock Pin UnitLens Lock Pin SpringMount Base Unit

7 Battery Unit (Fig. D14) Screw (U) x 2(Fig. D15) Jack Cover

Battery UnitFront Case UnitFront Spacer

8 AF LED P.C.B.,Battery P.C.B.

(Fig. D16) FPC TapeSolder (2 points)AF LED P.C.B.Screw (V) x 2Convex x 2Battery P.C.B.

9 Battery Door Unit (Fig. D17) Battery Door ShaftBattery Door SpringBattery Door Unit

10 Dial SW,Top P.C.B.

(Fig. D18) Screw (W) x 2FP7001 (Flex)Convex x 2Dial SWStrap Holder R UnitFP7002 (Flex)Screw (X) x 1

(Fig. D19) Main - Top FPCTop P.C.B.Power PanelMode Dial Rotor

11 LVF Unit (Fig. D20) Screw (Y) x 1Hooking part x 2Eye Cup UnitScrew (Z) x 1LVF Unit

12 Flash Unit (Fig. D21) Screw (a) x 1Screw (b) x 1Convex x 2Top PlateFlash Lock LeverFlash Lock SpringFlash Sheet

(Fig. D22) Convex x 1Convex x 2

(Fig. D23) Convex x 1Flash Unit

13 Hot Shoe Unit & MIC Unit

(Fig. D24) MIC Damper x 2Hot Shoe Unit & MIC Unit

No. Item Fig. Removal

41

9.1.3.1. Removal of the Rear Case Unit

(Fig. D1)

(Fig. D2)

42

(Fig. D3)

9.1.3.2. Removal of the Rear Plate Unitand LCD Unit

(Fig. D4)

43

(Fig. D5)

9.1.3.3. Removal of the Top Case Unit

(Fig. D6)

44

(Fig. D7)

9.1.3.4. Removal of the Main P.C.B. andSub P.C.B.

(Fig. D8)

45

9.1.3.5. Removal of the Image Sensor Unitand Shutter Unit

(Fig. D9)

(Fig. D10)

46

9.1.3.6. Removal of the Mount, Lens Ringand Mount Base Unit

(Fig. D11)

(Fig. D12)

47

(Fig. D13)

9.1.3.7. Removal of the Battery Unit

(Fig. D14)

(Fig. D15)

48

9.1.3.8. Removal of the AF LED P.C.B. andBattery P.C.B.

(Fig. D16)

9.1.3.9. Removal of the Battery Door Unit

(Fig. D17)

9.1.3.10. Removal of the Dial SW and TopP.C.B.

(Fig. D18)

49

(Fig. D19)

9.1.3.11. Removal of the LVF Unit

(Fig. D20)

50

9.1.3.12. Removal of the Flash Unit

(Fig. D21)

(Fig. D22)

51

(Fig. D23)

9.1.3.13. Removal of the Hot Shoe Unit &MIC Unit

(Fig. D24)

NOTE: (When Installing)Make sure to confirm the following points when installing:

• The Screw is tightened enough.• Installing conditions are fine. (No distortion, no abnormal-

space.)• No dust and/or dirt on image sensor surface. (live mos)• LCD image is fine. (No dust and/or dirt on it, and no gradient

images.)

9.2. Disassembly and AssemblyProcedure for the Lens

Please refer to the following service manuals about Disassem-bly and Assembly of bundled lenses.

• H-FS12032PP/E/GK: Order No.DSC1311036CE• H-FS35100PP/E/GK: Order No.DSC1410024CE• H-H020APP/E/GK: Order No.DSC1307028CE• H-FS14140PP/E/GK:

Order No.DSC1305023CE/DSC1506509SE

52

10 Measurements and Adjustments10.1. Matrix Chart for Replaced Part and Necessary AdjustmentThe relation between Replaced part and Necessary Adjustment is shown in the following table.When concerned part is replaced, be sure to achieve the necessary adjustment(s).As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.NOTE:

After adjustments have been terminated, make sure to achieve “Initial Settings”.After updates it to the latest firmware, the adjustment is executed.

*1 NOTE: (About Image Sensor Unit)When remove or turn the flange back adjustment screw, “Simplicity flange back adjustment” *2 is necessary.

53

*2 NOTE: (About Simplicity flange back adjustment)When remove or turn the flange back adjustment screw, “Simplicity flange back adjustment” is necessary.When remove the flange back adjustment screw, please don’t reuse it. Use new one.

[Abstract of “Simplicity flange back adjustment”]Set the camera in front of the chart and set center of the chart picture on LCD. When execute software, camera works AF on 5 spots automatically.Calculate flange back value at 5 spots and display on PC screen.Adjust flange back value within the specification by the 3 screws.The details are refer to adjustment manual in adjustment software.

The image sensor of this camera cannot be fixed when power is OFF.That is why, image sensor adjustment have to do power ON after assembly (only open the rear case). Stand-alone mount part cannot adjust.

*3 NOTE: (When exchange the Shutter Unit)After replacing the shutter unit, the shutter unit data has to be stored to the Flash-ROM (IC6003) on the Main P.C.B..The shutter unit supplied as service parts has affix the label of own configure data.By inputting second line to fourth line of these data into the adjustment software and writing these data to Flash-ROM (IC6003), the shutter adjustment becomes needless.In addition, the adjustment software can read data encoded to QR Code by using WEB camera with a close-up function.After that, proceed the main body adjustment.The details are refer to adjustment manual in adjustment software.

54

*4 NOTE: (When exchange the Main P.C.B. and/or Flash-ROM (IC6003))After exchanging the “Main P.C.B. and/or Flash-ROM”, first, execute “Initial Settings” to determine the model suffix, and then, cancel the “Initial Settings” and proceed the adjustments.When the adjustment data is rewrite without “Initial Settings” execution, may not be able to choose desire model suffix.During the “Initial Settings” (When the model suffix select screen is displayed), do not power off or do not remove the battery.* Power down during “Initial Settings” may cause not be able to choose desire model suffix.

When cannot be repaired in the IC exchange, and in the case of performing the “Main P.C.B.” exchange, carry out any of follow-ing.1. When it can turn on power, and the adjustment software can communicate with the camera body:

Before replacing, proceed the Flash-ROM (IC6003) data backup from the unit.After replacing, overwrite the Flash-ROM (IC6003) data with backup data from the unit.After that, proceed the main body adjustment. (Almost adjustment/inspection items can be omitted.)Refer to the adjustment instruction in the adjustment software for details.

2. When it cannot turn on power, or the adjustment software cannot communicate with the camera body:Almost readjustment fully are necessary.The details are refer to adjustment manual in adjustment software.

*5 NOTE: (When White Balance (WBL/WBM) adjustment)After change to WB adjustment mode for service with software, the adjustment is executed. After adjusting the AWB adjustment, to cancel the WB adjustment mode for service.The details are refer to adjustment manual in adjustment software.

*6 NOTE: (About the G sensor adjustment)Offset adjustment for built in electronic level.The details are refer to adjustment manual in adjustment software.

*7 NOTE: (About Gyro sensitive/DC offset adjustment)Gyro adjustment for BIS. Put to a normal state and execute automatic adjustment.The details are refer to adjustment manual in adjustment software.

About the 3D interchangeable lens (H-FT012) correspondenceThis unit has no special structure (circuit or part) for the 3D interchangeable lens correspondence, only by software is processedthe 3D interchangeable lens correspondence.Therefore, if taken with other lenses as usual, the 3D interchangeable lens is no problem for operation.

55

11 Maintenance11.1. Notice in External Cleaning11.1.1. About the BodyNOTE:

Before cleaning the camera, remove the battery and/or disconnect power plug from the outlet.Also, remove the memory card and lens unit.

11.1.1.1. Dust/Dirt on the Outer Casing Part (S)1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.2. Wipe up fingerprint and/or dirt on the Outer casing part with the dry fuzz-free cloth.

11.1.1.2. Dust/Dirt on the Image Sensor1. Blow off the dust on the surface of the Image sensor with the Blower. (Refer to the following Figure.)

• Keep the Mount Facing down condition towards to floor when cleaning.• Do not put the Blower further inside than the lens mount.• Be careful not to blow too strongly.

2. Wipe off the dirt on the image sensor surface with Lens Cleaning Kit (BK)(VFK1900BK).

11.1.1.3. About the LVF Unit[Procedures]

1. Refer to the “Disassembly & Assembly Instructions” and disassemble the LVF Unit.2. Blow off the dust of LVF Lens Unit with a blower.3. Wipe off the dirt on the surface of glasses with Lens Cleaning KIT (VFK1900BK), if necessary.

11.1.2. About the LensPlease refer to the following service manuals about Maintenance of bundled lenses.


56

DMC-GX80/85 OVERALL BLOCK DIAGRAM

MEMORYCARD

IC9101SYSTEM IC

MICROPHONE AMPSPEAKER AMPVIDEO OUT

ECM(R)

ECM(L) STEREOMICROPHONE

HDMITERMINAL

SPEAKER

W-LAN MODULE

Wi-FiANTENNA

IC9401LEVEL METER

BATTERY

CHARGE/USBTERMINAL

IC1001,1031,10918ch SW REGULATOR(POWER SUPPLY)/DC-DC CONVERTER/SYNCHRO STEP-DOWNCONVERTER

IC1501,1502,1503,1510IC1511BATTERY CHARGER/MICROCONTROLLERUSB SW/REGULATOR

IC1051,1231,1251,1411IC1431,1451,1471,1491IC6501,6502,6503,6504IC6505,6506,7201,8001IC8002,9201,9304REGULATOR/LOAD SW/DC-DC CONVERTER/SINGLE COMPARATOR

GYRO P.C.B.

57

12 Block Diagram12.1. Overall Block Diagram

REAR OPERATIONS

IC9901MOTOR DRIVE

FLASH

TOP OPERATIONS

LENS UNIT

X6001(24MHz)

LENS CONTACTTERMINALSSWF SHUTTER

UNIT BIS UNIT

Q9801, T9801

MOUNT BOX UNIT

MOS IMAGE SENSOR

(Built in AFE)

(27MHz)

IC6001VENUS ENGINE

CAMERA PROCESSJ-PEG COMP/EXPANDSMEDIA I/FUSB I/FMAIN MICROPROCESSOROIS CONTROLLENS DRIVELCD DRIVELP-DDR2 MOBILE RAM /8G-bitHDMI DRIVER

COLOR LVF 0.38” PANEL2760k dots

EXT. FLASH(OPTION) QR8002,8003HOT SHOE

UNIT

COLOR LCDPANEL

3.0” PANEL1040k dots

X9101(32.768kHz)

TOUCH PANEL

EYE SENSOR

IC9101SYSTEM IC

IC6003NOR FLASH ROM/1G-bit

4/3” 16 MEGA PIX

IC5001BIS DRIVER

TILT SENSOR

IC8101CHARGE CONTROLQ8101

IC5101GYRO AMP

GYRO(2-AXIS)

GYRO(1-AXIS)

IC9102,9103,9104LOGIC IC

HALL AMPREF AMP

12.2. System Control Block Diagram

DMC-GX80/85 SYSTEM CONTROL BLOCK DIAGRAM

FP900313

POWER LEDW D3.15V

FP900311

FP700322

FP900312

FP700321

FP900314

FP900318

REAR CASE1 UNIT

TOP P.C.B.

SHUTTER

FP90037

D PWR OUT)

TTER HALF)

TTER FULL)

USB WiFi LEDUB D3.0V

FP900322

FP700322

FP900310

FP700323

MENU/SET

FP90074

FP90073

1)

T)

2)

N)

FP90079

)

(Green)

(Red)

ODE DIAL0)

FP90038

FP700320

FP700319

FP700326

FP700325

FP90033

FP90035

FP700330

FP700328

FP90034

FP700329

ODE DIAL1)MODE DIAL

D USB WiFi)

FP90075

FP90076

FP900319

FP700314

RECS7001

S7002

S7003

D7003

D7001

(REC ON L)

FP900317

DIAL LED K)

DIAL LED A)

FP900316

MD DIAL F0)

FP900315

FP700316

FP700317

FP700318

MD DIAL F1)

IC7001

IC7002

2

1

4

3

2

1

4

3

HOT SHOE FPC

FP90072

PW D3.5V

FP700315

(CMD DIAL R1)

(CMD DIAL R0)

(PON ON L)

MD DIAL R1)

MD DIAL R0)

FP900320

FP700313

T STB DET) (INT STB DET)

CC)

FP700321

FP900312 D3.15V FP7002

3(HALL VCC)

(PON ON L)

FP70011

FP70013

FP70014

FP70024

CMD DIAL

REAR DIAL UNIT

6

5

(LCD OPEN DET)

2 3

41 VOUT

GND

VCC

N.C.

(FLASH POP-UP DET)

2 3

41 VOUT

GND

VCC

N.C.

POST FOCUS/FN

QMENU/FN

4K PHOTO

DSP ON L

AF AE LOCK

LCD EVF SEL

PLAY ON L

UP ON L

RIGHT ON L

LEFT ON L

DOWN ON L

58

(G I2C CK)(I2C SCK)

IC6001(VENUS ENGINE)

IC9101(SYSTEM IC)

(SHUT HALF)

P

(LED PWR OUT)

V3

(SHUTTER0)

(SHUT FULL)

(REAR THERMO)

K4

CS

SO

SI

SCLK

OSC IN

X9101(32.768KHz)

OSC OUT

(S SYS CS)

(S SYS SDIN)

(S SYS SDO)

(S SYS SCK)

RL9107

RL9117

RL9101

RL9108

RL9102

(REAR KEYIN1)

(REAR KEYIN2)

H1

J3

J4

J2

(SHUT HALF)

(S SYS CS)

(S SYS SDIN)

(S SYS SDO)

(S SYS SCK)

D21

C21

SHUTTER0

LEDOUT0

SHUTTERHALF

B2

X6001(24MHz)

AC27

AD27

(LE

(SHU

(SHU

S

V1

(CROSS KEYIN)

(REAR KEYIN

(LCD OPEN DE

(REAR KEYIN

(CROSS KEYIB21

PW A1.8V

(REAR THERMO

(M(MODE DIAL0)

V2(M(MODE DIAL1)

A17

N6

J1

K5

L5

L7

PIOD4 B4

LED USB WiFi(To IC1502-26)

(LE

(LED AF OUT)

(LED AF OUT)(LED AF OUT)

(D3R5V)

LEDOUT3B3LEDOUT2A3

E5

(SYS RESET)U7

(SYS RESET)RESETOUT H7

G4

J1

H3

K1

RL9122

RL9126

RL9112PIOA0

PIOA6

TH6001

W4

(LCD OPEN DET)A1

(PON ON L)

CL9008

(REC ON L)

(F

(F

(C

(C

(CMD DIAL F0)R4

(CMD DIAL F1)P6

AD10

FP7203

FP7203

51

53

FP720350

TOUCHPANEL

(INT)

(I2C SDA(TP))

(I2C SCL(TP))

(TSP INT)

(TSP SDA) (G I2C DAT)(I2C SDA)(TSP SDA)

(TSP SCK)

(TSP INT) (TP INT)

(TSP SCK)

FP940159 4

FP930112

FP940160

FP940128

28FP7201 FP9301

11

FP900135

FP9001

FP9001

6

FP940121,22,23

FP900140,41,42

FP94019

FP900154

FP9301930

FP7201

27FP7201

LCD UNIT

SUB P.C.B.

FLASH/BATTERY P.C.B.AF LED P.C.B.

CH7204

CH7205

CH7207

K3

K2

PW D3.15V

(V THERMO)

PW D3.15V

PW D3.15V

RL8103RL8202

RL8201

D8201

RL8104

(C

(C

(IN

(HALL V

PW

(CMD DIAL R1)

(CMD DIAL R0)

G16(INT STB DET)

IC5001(BIS DRIVER)

OUT6B

OUT6A

C8

VM6 C9

B9

PW D3.15VFP900525

FP810126

AF LED FP810125

FP900524

PW D3.15V

PW D3.15V

(LPSW) (LPSW)

CH500

CH500J11

RL6001

CL9402

CL9403

EYE SENSOR FPC

SLLK FPC UNIT

FP94031

FP94033

FP94036

FP94032

FP94041,2,3

(EYE SENSOR)

4

15

6 LEDALDR

3 GND

7 INT

LEDK VDD

8SDA

2SCL

INT2 6SDI

14VS15Reserved1VDD8CS

IC9401(LEVEL METER)

4SCL

11

9

INT1CL9404

CL9401

CL9405

M3

RL9103

H3(CLK27 SYS) (CLK27 SYS)

MCLK L1

DMC-GX80/85 VIDEO/AUDIO PROCESS(1) BLOCK DIAGRAM

D2+3D2-5D1+6D1-8D0+9D0-11

12 CK+CK-14CEC15SCL17SDA18

1

1 562

3 784

1 562

3 784

JK2002FL2001

FL2002

HPDTCT19 PW D5R

PW HDMI5.0V

1 2 3

6 5 4

001

Q2002

HDMITERMINAL

7

8

9

1

2

5

WP

4

D0

D1

D2

D3

CMD

CLK

WP

VDD

GNDVSS 3

G4GND G3

C.DETC

P9201(MEMORY CARD CONNECTOR)

CD

IC9201(REGULATOR)

23

4 1VOUT

GND

VIN

VCNT

123

4 65

Q9201

QR9202

QR9201

.15V

PW D3.15V

RL9116

CL9201

RL9201

RL9203

RL92026

QR2003

654

3 12

59

12.3. Video/Audio Process(1) Block Diagram


(IS PWR ON3)FP350238

FP30023

CLE

ALE

NW

PR

Y/N

BY

NC

EN

RE

NW

E

T26 T25 T24 T23

DAT

0

DAT

7

R25 R24 R23 T27 P27 P26N23 P24 P23 R26P25

ADDRESS/DATA

564841 59 525857

IC6003(NAND FLASH ROM/1G-bit)

17 8 7 12 10 16 11

CTL SIG

IC9101(SYSTEM IC)

(IS PWR ON3)PIOB5D11

AA23AF21

AG22AF22AG21

AF23

(G HDMI D2+)(G HDMI D2-)(G HDMI D1+)(G HDMI D1-)(G HDMI D0+)(G HDMI D0-)(G HDMI CK+)(G HDMI CK-)(HDMI CEC)

AF24AG24

AG23

Q2

PW D3.15V

AC24(HDMI HPD)

AB23(G HDMI SCL)B11(READ SCL)

AB24(G HDMI SDA)

(SDCD SYS)

(SDCD SYS)

(SD CD)SDDETIN

PIOB1

PIOB0

SDDETOUT

(SD 1.8V ON)

(SD UHS1 ON)H10

PIOB2(SD POW ON L)

E11

F7

D3

(REGULATOR)

(REGULATOR)

(REGULATOR)

PW D3

B7

W27

V26

U26

U27

V27

W26

(SDWP)

(SD DAT0)

(SD DAT1)

(SD DAT2)

(SD DAT3)

(SD CMD)

(CLK SD)

A7

RL9120

RL9127

CL9203

(PW SD0 3018V)V21V20

G6

MOSIMAGE

SENSOR16MEGA PIX

MOUNTBACEUNIT

FP350237

FP30024

(Built in AFE)

IS P.C.B.

VOUT VIN

CE2 3

41

VSS PW D5.2V

PW VCHP1

VOUT VIN

CE2 3

41

VSS

(REGULATOR)

(REGULATOR)

VOUT VIN

CE2 3

41

VSS

PW D3.5V

PW AVDDP

PW IS1.8V

VOUT VIN

CE2 3

41

VSS

PW AVDD

PW DVDD

PW D3.5V

PW D3.5V

PW IS3.3V VOUT VIN

CE2 3

41

VSS

IMAGE SENSOR UNIT(SENSOR)

SSWF FPC

FP350138

Q9801

8 1

276 3

453

4

1

6

T9801

FP30013

FP30031,2,3

FP30034,5,6

(SSWF OUT)2

PW D5.0V

(SSWF OUT1)

(SSWF OUT0)

SSWF1OUT

SSWF0OUT

E2

E3

SSWF OUT

UNREG GND

RL9111

RL9114

(SSWF ON H)

(SSWFOUT SYS)

(SSWF ON H)

(SSWFOUT SYS)

E22

D27

SSWF CTL F4

SSWF IN F1

(SDODA0P)

(SDODA0M)

(SDOCAP)

(SDOCAM)

(SDODA3P)

(SDODA3M)

(SDODB3P)

(SDODB3M)

(SDOCBP)

(SDOCBM)

(SDODB2P)

(SDODB1P)

(SDODB1M)

M27

K26

J27

J26

H27

H26

G27

G26

F27

E27

E26

K27

M26

(SDODB2M)F26

FP35023

FP300238

FP35024

FP350218

FP350219

FP350221

FP350222

FP350224

FP350225

FP350227

FP350228

(SDODB0P)

(SDODB0M)E25

E24

FP350230

FP350231

(SDODA1P)

(SDODA1M)L27

L26

FP35026

FP35027

FP350212

FP350213

(SDODA2P)

(SDODA2M)L24

L25FP35029

FP350210

FP350215

FP350216

C2

FP300237C1

FP300235D2

FP300234D1

FP300232E2

FP300231E1

FP300229F2

FP300228F1

FP300226G2

FP300225G1

FP300223L2

FP300222L1

FP300220M2

FP300219M1

FP300217N2

FP300216N1

P2

FP300213P1

FP300211R2

FP300210R1

FP300214

(IS CS)

(IS SDO)

(IS SCK)

C22

A22

B22FP350236

FP350235

FP350234

FP30025

FP30026

FP30027A14

B13

B14

(IS THERMO)W3FP3502

39FP3002

2

(IS VD)

(IS HD)B23

A23

FP350118

FP350117

FP300123

FP300124

A13

A12(IS PSV)

AE12FP350116

FP300125B11

(CLK27 IS FCK)R27FP3501

31FP3001

10

FP350114

FP300127

A11

(IS PWR ON2)(IS PWR ON2)PIOB7E8

PW D3.15V

FP35016,7

FP300134,35

FP35018,9

FP300132,33

PIOA7H9(IS PWR ON1)

Q3501

QR3501

PW IS1.2V

PW ISDM1.2V

PW D1.2V 1

PW D5.2V

12.4. Video/Audio Process(2) Block Diagram

DMC-GX80/85 VIDEO/AUDIO PROCESS(2) BLOCK DIAGRAM

LCD

45FP7203

30FP7203

27FP7203

VSYNC

HSYNC

PCLK

CSX

DIN(MOSI)

SCL

RESX

LEDPWM

26FP7203

28FP7203

46FP7203

49FP7203

47FP7203

AN LCD(18.0V)

52FP7203

25FP7203

21FP7203

3,4FP7202

VCI(3.1V)16

FP7203

CA LCD

VSWP

VSWN

VSN

1,2FP7202

19FP7203

VSP20

FP7203

2

QR7201

1 2 3

46 5

Q7201

6

1

1 2 3

6 5 4

Q7202

18FP7203

CH7203

CH7202

CH7206

CH7201

(G SP POG)

(G SP NEG)

RL7101

RL7102 SPEAKER

REAR PLATE UNIT

FP700225

FP700224

LIN)

RIN)

RL7301

RL7302

FP700223

FP700222

FP900330

FP900331

FP900332

FP900333

FP70033

FP70032

FP70031

FP70034

+-

ECM(R)

ECM(L)

+-

STEREOMICROPHONE

(MIC GND)

(MIC GND)

(ECM RIN)

(ECM LIN)

RL7303

RL7304

HOT SHOE FPCTOP P.C.B.

60

PW HDMI5.0V


FP940112

FP940110

FP940152

37FP9401

7FP7201

22FP7201

3FP7201

24FP7201

26FP7201

FP940111 25

FP7201

2FP7201

5FP7201

14FP9302

29FP9302

Y23

AE5

AD9

(CSX)

(SDO(MOSI))

(SCL)

LVF

FP940129

FP7201(RES)

(PCLK)

(HSYNC)

(VSYNC)

(CLK65 EVF)

(BUS65 EVFHD)

(BUS65 EVFVD)

(LCD BLT)

(EVF POWER)

LCD UNIT

FP93023

FP93025

FP93028

7FP9302

12,13FP9302

9-11FP9302

30FP9302

FP930231

33,34FP7201

32FP9301

17FP9301

36FP9301

15FP9301

13FP9301

14FP9301

37FP9301

34FP9301

10FP9301

5,6FP9301

19,20FP9401

SUB P.C.B.

7

FP900131

FP900133

FP900126

11FP9001

FP900132

FP9001

36,37FP9001

37

PW UNREG SYS

(CLOCK)

(HSYNC)

(VSYNC)

(SCL)

(SDA)

(AVCC(5V))

31FP7201

(S MON SCK)

(S MON SDO)Y24

(S MON CS)

BUS54 EVF0-15

W23

AG9

AF9

AE9

(MON RST)AA24

(I2C CK)

(I2C DAT)

BUS65 EVF0-15BUS65 EVF0-15

PW D3.15V

(EVF POWER)

IC9101(SYSTEM IC)

PIOC2

PIOC1

D9

C10

(LCD BLT)

CL720

CL7201

CL7204

CL7203

IC7201(DC/DC CONVERTER)

4

QS

R

CURRENTSENSE

THERMALSHUTDOWN

SHUTDOWNDELAY

CURRENTLIMIT

OVP

UVLO

OSCCE

DRIVERCONTROL

ERR.AMP

PWMCOMP.

VOUT

EN

GND

FB

LXVCC

ENB

3

25

6

SLOPECOM-

PENSATION

1

VREF

QR720254

3 2

IP9301

PWMCNTRL

FP930134

FP940129

FP9001

35FP9401

28FP9001

59FP9401

60FP9401

4FP9001

3FP9001

54FP9401

9FP9001

56FP9401

7FP9001

57FP9401

6FP9001

(NRESET)(EVF RES)27

FP940136

FP9001

CH9301

CH9304

(G I2C CK)K2

(G I2C DAT)K3

8

CL9305

CL9304

CL9303

(EVF RESET)PIOC0 C11

CH9016

CH9015

IC9304(REGULATOR)

VOUTVDD

CE 23

4 1

VSSQR9302

6

5

4 3

1

2

4FP9302

6FP9302

(VIO Selial (3.3V))

(VCCX (3.3V))

(VCC (1.8V))

BUS65 EVF0-15

PW D3.5V

PW EVF1.8V

PW EVF1.8V

LRCLK

G3(AUD DIN)

(AUD FCLK)RL9105

RL9109

RL9104

RL9110

(AUD DOUT)RL9106

ADOUT

DA ING2

H4(AUD MCLK)

(AUD DCLK)

MCLKO

BCLKG1

G4 L2

K3

K2

J3

H4

(G MIC LIN)

(MREG)

(G MIC RIN)MICINL1

MICINR1

C8

MREG

C7

CL9102

CL9103

(G SP POG)

(G SP NEG)SPPOS

SPNEG

7FP9007

8FP9007

G11

F11

D7

(G MIC

(G MIC

CL9105

CL9106

DMC-GX80/85 GYRO/WiFi BLOCK DIAGRAM

IC5302

CSB

A ch

fc: : 2KHz

fc: : 2KHz

SCLK

MISO

MOSI

GYRO SENSOR:2-AXIS)

SPII/F LPF

REG

REG

DIGITAL BLOCK

VREGD

VCC

A/DSENSEBLOCK

TUNINGFORK

VDD

16I/F BLOCK

SL

GND1GND2GND3

B ch

LPF A/DSENSEBLOCK

TUNINGFORK

100k 100k

100k

100k

ANALOG BLOCK

VREGA

V1

14

3

IC5301(GYRO SENSOR:1-AXIS)

5 Vout

Vref

7 Sleep

8 Vdd

3

4GND

N.C.

2N.C.

1N.C.

INT2

1 SCL/SPC

IC2701(TILT SENSOR)

2 CS

3 SDO/SA0

4 SDA/SDI/SDO

12

11

INT1

9 VDD10 VDD IO

6

IC8501(W-LAN MODULE) Wi-Fi

ANTENNASDIO CLK12

SDIO CMD13

SDIO D0

2.4G ANT

11

SDIO D110

SDIO D215

SDIO D314

31

RESET N29

1-4FP8501

RL7651

GYRO/WIFI P.C.B.

8501

05

02

03

61

12.5. Gyro/WiFi Block Diagram


FP900630,31

FP9006

FP9006

FP9006

FP900626

FP53011

FP5301

FP5301

FP5301

FP53015

9

10

11

(

7

12

8

246

1

29 2

28 3

FP9006 FP530124 7

FP9006 FP530123 8

FP9006 FP53019 15

FP9006 FP53018 12

FP9006 FP53017 11

FP9006 FP53016 14

FP9006 FP53015 13

27 4

(S BISACC IRQ)

(PW VDD33)

(OIS GYRO CS)(OIS GYRO CS)

(SAMB S SCK)

(SAMB S SDOUT)

(SAMB S SDIN)

(G GYRO CS)

(CLK9 SAMBA)

(SAMB S SCK)

(SAMB S CS)CSIO CS SRDY N

(SAMB S SDOUT)

(SAMB S SDIN)

(SAMB S SDIN)

(SAMB S SCK)

(SAMB S SDOUT)

(OIS GYRO SCK)

(OIS GYRO DI)

(OIS GYRO DO)

PW VDD33

FP900625

FP53016

(PW GY3R0V)PW GY3.0V

FP900625

FP530116,17

(PW D3R15V)PW D3.15V

(G GYRO OUT)(G GYRO OUT)

(G GYRO ROLL)

(G GYRO DAC)

(G GYRO REF) (G GYRO REF)

(S BISACC SDI)

(S BISACC SCK)

(S BISACC CS)

(S BISACC SDO)

(S BISACC IRQ)

(S BISACC SDI)

(S BISACC SCK)

(S BISACC CS)

(S BISACC SDO)

(S BISACC IRQ)

(S BISACC SDI)

(S BISACC SCK)

(S BISACC CS)

(S BISACC SDO)

PW GY3.0V

VSS

IC5101(GYRO AMP)

23

4

1

5VDD

A16

A15

N2

C17

N3

N4

RL2701

CH6004

CH6005

CH6006

CH6008

CH6007

IC5001(BIS DRIVER)

ADIN EXT3 G4

A1

A3

HAY DAOUT K7

P00 G2

CSIO SCLK

CSIO RXD

C2

CSIO TXD B2

CH5041

CH5011

CH5012

CH5013

CH5014

CH5015

B16

D15

C16

(SAMB M SCK)CSIO HS SCLKID2L2

(SAMB M SDIN)CSIO HS TXDC3L3

(SAMB M SDOUT)CSIO HS RXDC1L4

(SAMB M CS)CSIO HS CS ND4K1

CH5036 (SAMB RSV3)MSIO TXD(ICUIN9)F1M2

CH5035 (SAMB RSV2)MSIO CS(ICUIN8)E1G15

CH5004 (SAMB RESET)SYSRST NA4T7

CH5034 (SAMB RSV1)P01(ICUIN1)G1T6

CH5033 (SAMB INTIN3)MOB1D1R6

(SAMB M HSRDY)CSIO HS SRDYO NB3P1

CH5031(SAMB INTIN1)

MSIO SCLKF2R7

CH5032(SAMB INTIN2)

MSIO RXDE2P7

(G WiFi CLK)

(WiFi CMD)

(WiFi DAT0) (WiFi DAT0)

(WiFi DAT1)

(WiFi DAT2)

(WiFi DAT3)

(CLK27 SYS)

(G WiFi CLK)

(WiFi CMD)

(WiFi DAT1)

(WiFi DAT2)

(WiFi DAT3)

(WiFi RESET)

A8

B8

C8

D8

C9

D9

3FP9006

8FP9006

12FP9006

9FP9006

5FP9006

11FP9006

10FP9006

28FP5301

23FP5301

19FP5301

22FP5301

20FP5301

21FP5301

26FP5301

RL8506

RL

RL8504

RL85

RL85

RL85

IC9103(LOGIC IC)

1 CK

D

3 NQ

4 GND

7

8VCC

PR

6CLR

5Q

2

PW D3.15V PW D3.15V PW D3.15VIC9102(LOGIC IC)

2

1 5

3 4

VCCINB

INA

GND OUT RL9130

RL9131

IC9104(LOGIC IC)

1 CK

D

3 NQ

4 GND

7

8VCC

PR

6CLR

5Q

2

IC9101(SYSTEM IC)

(WiFi RESET)PIOB6D10

RESETOUT

CLOCK A2

H7H3

FRONT CASE UNIT

12.6. Flash/Hot Shoe Block Diagram

DMC-GX80/85 FLASH/HOT SHOE BLOCK DIAGRAM

AGC

D7004

FP700216-18

FP700212

FP700211

FP700210

STX(STX)

STTXD

STRXD

STRTTL

HOT SHOE FPC

HOT SHOE

FP70026-8

EXTB5R2V

RL8101 RL8301

RL8302RL8102

RL8401

RL8403

RL8404

RL8402

(LAMP+)

(TRG 1st)

(TRG GND)

FLASH

FLASH UNIT

RL7305

RL7306

RL7307

RL7308

RL7309

C8301(For Flash Charge)

RL8303(MC+)

FLASH P.C.B. UNIT

RL8304(MC-)

RL8307(EARTH

SPRING)

FP810224-29

(LAMP-) FP810214-19

FP81027-9

FP81021-3

P P.C.B.

62


(STB TRG)

(STB TRG)

(EXT STB IN)

(EXT STB DET)

Q7001

(EXT STB TRG)

(EXT STB DET)

(EXT STB TRG)

(EXT STB DET)

(STTXD)(STTXD)

(STRXD)(STRXD)

(STRTTL)(STRTTL)

(PW EXTSTB5R0V)PW EXTSTB5.0V

PW D3.15V

QR8002

3 2 1

64 5

PW D3.15V

PW D3.15V

QR8003

3 2 1

64 5

(EXT STB OUT)

(EXT STRTTL)

BATTERY P.C.B.

FP900523

FP810124PW D3.5V

FP81011-9 2

1

3

4

BATTERY P81011

6

8

7

9

(CHARGE CONTROL)

VREF

SDP

I/V

SDP

START

DRIVER

MAX ONTIME

START

RADJ

UVLO

5VCC

VCC

VCC

STBUVLO

TSD TSD

STB

OFF

S QR

SQR

S QR

MAX OFF TIME

FULL

ENABLE

SDPSTB

STB

UVLOTSD

MAX ONMAX.ON

LOGIC

VCC

PGND

1

4

3

PGND

GND

VC

IGBT OUT

SW

FULLFULL

IGBT IN

OS

OS

OFF

2

10

FP90051-8PW UNREG

CL8102

IP8102

IP8101

CL8110

T8101

8

1

765

23

4

(STB CHG START) FP810120

FP900519

CL8108

FP900520

FP810121

(STB CHG DET)

(STB CHG DET)

CL8109

FP900518

FP810119

(INT STB TRG)(INT STB TRG)

IC9101(SYSTEM IC)

INT STB TRG

(STB CHG START)

RL9125

RL9113

RL9132

CH8003

CH8002

LVL SHIFTB0 D1

EXT STB TRG F2

PIOD3 A4

B14

F3

H2

P3

P2

T1

A11

Q8101

IC8101

TO

FP900321

FP700312

FP900322

FP700311

FP900328

FP70035

FP900327

FP70036

FP900323

FP700310

FP900324-26

FP70037-9

(EXT STB TRG)

DMC-GX80/85 LENS BLOCK DIAGRAM


G13

F13

A13

A14

D13

F12

C13

(S LSDIO)

(S LSB2L)

(LSDET)

(LSRST)

(S LSL2B)

(S LSCK)

(S LSB2A)

(S LSLDPO)F14

(SHUT MT1 B)

(SHUT MT1 A)

(SHUT MT2 A)

(SHUT MT2 B)

(M DRIVE CTL)

CH5051

IC9101(SYSTEM IC)

DACOUT0

DACOUT1

G8

G9

C15

A12

B13

A21

F17

F16

F18

G18

(SHUT PI CTL)

(G YHOUT T)

D18

VSS

IC5201(REF AMP)

2 3

4

1

5VDD

IC5202(HALL AMP)

5

4

7

2 1

8

3

6

PW A3.0V

PW A3.0V

GND

VCC

E21

(G X1HOUT T)D20

(G X2HOUT T)E20

63

12.7. Lens Block Diagram

SUB P.C.B.

FP90044

FP90043

FP90048

FP90046

FP90045

FP90041

FP90047

FP90042

LSDET

LSRST

LSB2L

LSL2B

LSDIO

LSCK

LSB2A

LSLDP

FP900416-21 PW LEN4.2VLEN4R2V

(S LSDIO)

(S LSB2L)

(LSDET)

(LSRST)

(S LSL2B)

(S LSCK)

(S LSB2A)

(S LSLDPO)

(LENS RELEASEFPC PLATE)

(SHUTTER FPC)

(MOUNT BASE UNIT)

4,5FP9901MOT 1B

MOT 1A

MOT 2A

MOT 2B

PI 1C E

PI 2C E

SHUT THERMO

PI 1C K

PI 2C K

(SHUT MT1 B)

(SHUT MT1 A)

(SHUT MT2 A)

(SHUT MT2 B)

(SHUT MT1 B)

(SHUT MT1 A)

(SHUT MT2 A)

(SHUT MT2 B)

FP99016,7

FP99011

FP99012

FP990114

(SHUT PI IN1) (SHUT PI IN1)

(SHUT PI IN2)

(SHUT PI K) (SHUT PI K)

(SHUT PI K)

CH9007

CH5022

CH5023

CH5021

CH9009

CH9008

CH9010

CH9011

CH9013

CH9012

CH9014

IC9901(SHUTTER DRIVER)

11 OUT1B

OUT1A

OUT2A

OUT2B

CR1

IN1B

IN1A

IN2A

IN2B

15

14

10

7

19

18

6

8,9FP9901

FP990110,11

CH9901 CH9910

CH9909

CH9906

CH9907

CH9903

CH9002

CH9004

FP940221 4

FP9002

FP940222 3

FP9002

FP940220 5

FP9002

FP940219 6

FP9002

(M DRIVE CTL) (M DRIVE CTL)PS 2

CH9908FP9402

23 2FP9002

(SHUT DACOUT1)VLIM1 3

CH9917 CH9911FP940213,14 11,12

FP9002

(SHUT DACOUT2)

(SHUT DACOUT1)

(SHUT DACOUT2)VLIM2 22

CH9916

CH9912

CH9913

CH9914

CH9918

CH5003

CH9905FP940211,12 13,14

FP9002

FP940217 8

FP9002

FP940218 7

FP9002

FP940216 9

FP9002

FP94014 59

FP9001

5

CR220

SENSE14

1

RNF1

GND

12

VM1 9VM2 16

PW SHUT9.0V

VREF 23VCC 24

PW VDD33

FP990113

FP990115

( SHUT THERMO) ( SHUT THERMO)

(SHUT PI IN2)

HA2Y OUT

IC5001(BIS DRIVER)

B6PI1 B5

OUT5AD8

OUT-

OUT+

IN-

1 2

34

IN+

(PIT )

(YHO+)FP350121

FP300120

(YHO-)

(Hall IN+)

FP350122

FP300119

(YHI-)FP350120

FP300121

FP350129

FP300112

OUT-

OUT+

IN-

1 2

34

IN+

(Yaw1)

(X1HO+)FP350124

FP300117

(X1HO-)FP350123

FP300118

(X1HI-)FP350125

FP300116

OUT-

OUT+

IN-

1 2

34

IN+

(Yaw2)

(X2HO+)FP350127

FP300114

(X2HO-)

(X2DR-)

FP350126

FP300115

(X2HI-)FP350128

FP300113

FP350136

FP30015

FP350135

FP30016

FP350134

FP30017

FP350133

FP30018

PW A3.0V

PW A3.0V

RL3004(X2DR+)

(X1DR+)

(X1DR-)

RL3003(YDR+)

RL3001(YDR-)

RL3002

FP35014

FP300137

FP35013

FP300138

RL3005

RL3006

SENSE2 21RNF2 13

Q5001

HA2Y INN

HA2Y INP

C6

D6

HA2X INPHAX DAOUT

C4J7

HDX INJ8HDX SENK8

HA2X INND5

ADIN EXT1H4HA2X OUTC5

HDY INK9

OUTIS2BE8OUTIS2AD9OUT3AG8OUT3BG9OUTIS1AF7OUTIS1BE7

HDY SENK10

HA1X INPF4HA1X INNG5HA1Y INPG6HA1Y INNH6

(SHUT PI CTL)INA F6

12.8. Power(1) Block Diagram

DMC-GX80/85 POWER(1) BLOCK DIAGRAM

PW D1.2V 1

PW UNREG

PW D1.2V

PW D3.5V

PW D5.2V

PW DVCC18

PW LEN4.2V

PW HDMI5.0V

IC1471(REGULATOR)

23

4 1VOUT

VSS

VIN

CE

IC1451(REGULATOR)

23

4 1VOUT

VSS

VIN

CE

IC1231(REGULATOR)

23

4 1VOUT

VSS

VIN

EN

PW D3.15V

PW AVCC33

CL1201

CL1451

CL1301

CL1401

CL1471

PW VDD33

IC1491(REGULATOR)

23

4 1VOUT

VSS

VIN

CE

CL1491

PW A3.1V

IC1411(REGULATOR)

23

4 1VOUT

VSS

VIN

CE

CL1411

CL1601

CL1701

CL1801

PW A1.8V

CL1231

IC1431(REGULATOR)

23

4 1VOUT

VSS

VIN

EN

PW D1.8V

CL1431

PW EVF1.8V

D12711

32

51C CONVERTER)

6CURRENT

PROTECTION

CURRENTFEEDBACK

RAMPCOMPENSATION

LX

REF

OSCILLATOR

PWM

OFTTART UVLO

SWITCHINGCONTROL

DE

5GND

+

CHIPENABLE

4VOUT

CL1251

PW -0.95V

CL1271

4

3

4

5

3

1 6

Q1271

4

5

3

1

2

6

Q1272

2

64

IC9101(SYSTEM IC)

POWERSWONL

POWERSWONH

VREGD

27VREGDVREGD2

62Hx1

Hx1

ERROR AMP1SERIAL I/F

ERROR AMP2

ERROR AMP3

ERROR AMP4

ERROR AMP5

ERROR AMP6

ERROR AMP7

CH1STEP DOWN DC/DC

(Current mode)64

Lx1

60PGND1

57Hx2

CH2STEP DOWN DC/DC

(Current mode)58

Lx2

59 PGND1

63Lx1

54Hx3

CH3STEP DOWN DC/DC

(Current mode)55

Lx3

53 PGND3

49Hx4

50Hx4

CH4STEP DOWN DC/DC

(Current mode)51

Lx4

52 PGND3

CH5STEP DOWN DC/DC

(Current mode)

CH6STEP DOWN DC/DC

(Current mode)DRIVER

PROTECTION

SCP6TIMER

SCPTIMER

SS TIMER

12 21RTSEQ

OSC

UVLO

LDO

OVPCOMP

SHUTDOWN

VREGA

C

CPDRIVER

P SW

1 VCC

23 CPLUS

CP SW 24 CMINUS

VREGD

VREGD2

29VREGA

20GND

0.3V

44 Hx5

47Lx5

Lx5

43PGND5

38 Hx6

39 Hx6HVREGDRIVER

VREGDDRIVER

HVREGDRIVER

VREGDDRIVER

HVREGDRIVER

VREGDDRIVER

HVREGDRIVER

VREGDDRIVER

HVREGDRIVER

VREGDDRIVER

HVREGDRIVER

40Lx6

42 PGND5

46

41 Lx6

VREGD

VREGD

CH7STEP UP DC/DC(Current mode)

DRIVER 34 PGND7

33 VO7

SERIALI/F

ON/OFFLOGIC

35 Lx7

61

25HVREG

2

IC1001(8CH SW REGULATOR)

56PGND2

48 PGND4

26

11

VBAT

3VBAT

45 Hx5

(POWER SW IN)


R2

(G I2C CK)K2

CL1002

(G I2C DAT)K3

CL1101

(SW UNREG)W1 SW UNREG

SERIAL I/F

Vo3SEL

SERIAL I/F

SERIAL I/F

SERIAL I/F

SERIAL I/F

SERIAL I/F

37PGND6

36 PGND6

30VINREG

VINREG

REGOUT

VDD

VREGD2IN

31

22

28

SCPLDOTIMER

10

16

CTL SEQ3

VO3SEL

CTL SEQ2

CTL SEQ1

CTL123417

18SCL

19SDA

14

13

32INV7

VO69

VO58

VO47

VO36

VO25

4VO1

(POWER ON L)

RL9118

K7

L10

D2

P8101

BAT+ 1IP8101

BAT THERMO 2

BAT DET 3

BAT- 4

22

1-9

21

11-18 10-17

1-8FP8101

FP8101

FP9005

FP9005

FP8101 FP9005 (UNREG)

(UNREG GND)

27-29 26,27FP8101 FP9005 (D GND)

(THERMO)

23 22FP8101 FP9005 (BAT D)

TOBATTERYCATCHER

CC8101

(POWER ON L)

(BACK BAT+)31

FP70032

FP9003

27FP7003

6FP9003

BACK BATTB7001

S7004

BATT H5(BACK BAT+)

CL9001

CL9002

CL9004

CL9005

BATTERY P.C.B.

TOP P.C.B.

POWER SW

POW CTL 2(From IC1502-32)

CH9006

IC12(DC/D

V

SS

VIN

MO

1

2

CE3

QR1271

6 5

1 2

PIOB7(IS PWR ON2)

E8

BAT D(To IC1502-8)

BATT THERMO(To IC1501-D4,Q1505-C)


PW D1.0V

PW D1.0V A

PW D1.0V B

CONVERTER)

6SW

SW

7SW

UGATE

LGATE

VIN

FB

VBIASR

ON-TIME

PGND

PGOOD

FB

0.9 VREF

DRIVERITCHROLLER

URRENTECTION

3

T1

5

8BOOT

PVCC

PVCC

CL1091

VREF

+-

ORPGOOD

COMPARATOR2

PW BIS5.2V

CL1031COMP.

COMP.

PW SHUT9.0V

CL1051

7LX

FB

GATEDRIVEPOWER

CONT.

PGCONT.UVLO

TIMERtON

HSLIM

LSLIM

1PGND

OMP.5

PG

VOS6

8

8765

1234

1051

65


IC9101(SYSTEM IC)

POW CTL 1(From IC1502-18)


IP1002

EV3

(PW UNREG SYS)

(PW DRAM1.2V)

(PW DRAM1.8V)

(PW DRAM1.2V A)

(EVER 3V)

(POWER CTL SW)

K6

OVERCUT H8

FBREG K10

G7

IC6503(REGULATOR)

2 3

41 VOUT

GND

VCC

CE

IC6506(LOAD SW)

3 2

14 VOUT

VIN

GND

CE

A3

IC6502(REGULATOR)

2 3

41 VOUT

GND

VCC

CE

IC6504(LOAD SW)

3 2

14 VOUT

VIN

GND

CE

AE2

C26

(PW DRAM1.0V)

H5

C1

POWERCTLSW L9

AG4

A24

IC6501(REGULATOR)

2 3

41 VOUT

GND

GND

VCC

CE

IC6505(LOAD SW)

4

3

1 VOUT VIN

CE

BACKUP CTL5J10

QR6501

M8(BACKUP CTL1)

BACKUP CTL1K9

G12(BACKUP CTL2)

BACKUP CTL2L11

PW UNREG

PW D1.2V

IC1091(SYNCHRONOUS STEP-DOWN

9

10

VIN

VIN

SS

EN

RIPPLEGEN.

EN

INTERNAL REGULATO

SWCONT

OVER CPROT

UNDER & OVERVOLTAGE

PROTECTION

PVCC

FBCOMPARAT

+-

-

2 A4

1

POWERONHJ7

(BACKUP CTL4)BACKUP CTL4 K11

PW D1.8V

PW D1.0V B

(BACKUP CTL3)BACKUP CTL3 J9

2

IC1031(DC/DC CONVERTER)

4

3

2VIN

ENCONT.LOGIC

SOFTSTART

THERMALSHTDWN

DIRECT CONT. & COMPENSATION

AGND

C

ERRORAMP-+

IC1051(REGULATOR)

1

2

3 8

10

9

GDRV

VDDRC

DIS/EN

SS BP

4 7ISNSCOMP

5 6GNDFB

Q

PW HDMI5.0V

PW EVER 3V

PW D3.5V

CH9101


REGISTERBANK

I/O C

ELL

I2C CORE


PW EVER 3V

SUB D3.0V

PVBUSLDO

BOOST-CHARGER

CONTROLLER

EOCCURRENT

SENSE

WAKE-UPCHARGING

VDDP1 VDDP2 LX1 LX2 BSTSYS1

SYS2

A3 B3 D1 D2 A1

A SCL GNDP1D6 E6

I/O C

ELL

C1

C2

COMP

GNDA

BATTG

BATT1

BATT2

E3

E5

A2

B1

B2

1

2

3 4

6

5

Q1502

PW UNREG

SUB D3.0V

UB D3.0V

E1GNDP2

E2

Q1508

PW EXTSTB5.2V

CH8004

CL8001

12

65

IC8002(LOAD SWITCH)

VOUT

VOUT

VIN

CURRENTLIMIT

THERMALSHUTDOWN SLEW RATE

CONTROLDRIVER

OUTPUTDISCHARGE

CONTROLLOGIC

GND

1

2

5

VIN

CNT

6

4

3

PULLDOWN

12

65

PARATOR)

66

(I2C SCL )

(BAT CAPA )

(BAT ON)

AUX LDO

THERMISTORBLOCK

VOLTAGESMONITOR

INPUT CURRENT LIMIT

CONTROLLOGIC

VREF LED

LEDDRIVER

BANDGAPBIAS

AND VOLTAGEREFERENCES

JK2001

USB VBUS 1IP2001

(CHARGE/USB TERMINAL)

IC1501(BATTERY CHARGER)

IC1502(MICROCONTROLLERS)

CL2003

D- 2

D+ 3

CL2001CL2002

PFI-OSC OUT

3 2

14

L2001


(G SW USB+)

(G SW USB-)

(USB CHG RXD)

AF16

AG16

IC1503(USB SW)

LOGICCONTROL

CHARGEPUMP

DN

D-

HDN

AUDN

5

VCC3

9

8

4

11

7

6DP

D+

IN1

IN2

HDP

GND

AUDP

1

10

2

12

3

(I2C SDA )PFI-OSC IN 2

IC1511(REGULATOR)

4 3

1

25

6

VSS

VIN

VOUT

CE

NC

NC

IC1510(REGULATOR)

4 3

1

25

6

VSS

VIN

VOUT

CE

NC

NC

PW UNREG

CHARGEPUMP

OSCILLATOR

E4VDDA

VBUS2

VBUS1

THM

B5

A4

B4

D4

C5IBS

C4PVBUS

A5

PORTDETECTION

RIDC6

DMB6

DPA6

SUS

VI2C SD

C3

D5

RIDBLOCK

SUB D3.0V

S

DD OND3

(DD ON)

(ISENSE)

PA15

PB5

25

QR1503

Q1505

QR1504

QR1505

28

(IN2)PB115

(IN1)PB014

(TH ST)

(USB DM)

(USB DP)

PA0

PA11

PA12

6

21

(USB OK)PB427

PW HDMI5.0V

Q1506

BATT THERMO

(USB VBUS)AC18

(POW CTL SW2)

22

C12(UART1 TX)

PB629

(USB CHG TXD)Q1507

PW D3.15V

D12(UART1 RX)

PB730

(POW CTL 1)POW CTL 1(To IC1091-1 )

PA818

(POW CTL 2)POW CTL 2(To IC1001-17 )

PB832

PB216

PA28BAT D(From P8101-3 )

PB326LED USB WIFI(From D7003-K )

IC9101(SYSTEM IC)

POWERCTLSW(POWER CTL SW)

L9

CL1596

SUB D3.0V

RL1502

(EXSTB PWR ON)

3

4

Q8002QR8005

3

4

Q8003

5

2

4

3 1

6

OUTVS

S

+IN

-IN VDD

NC

IC8001(SINGLE COM

(EXSTB CHG ON)

PIOB4 E9

PIOB3 E10

PW D5.2V

PW D5.2V

PA6 12

PA3 9

(SEL VCNT )PA7 13

PA1 7

VDD1VDDA5VDDIO217

BOOT0-PF11 31

PA4 10 CH1506

PA5 11 CH1505

PA9 19 CH1503

PA10 20 CH1504

DMC-GX80/85 INTERCONNECTION DIAGRAM

REAR OP FPC

EC

M R

INM

IC G

ND

STR

XD

PW

EX

TSTB

5R0V

PW

EX

TSTB

5R0V

EX

T S

TB D

ET

INT

STB

DE

TFD

IAL

LED

AC

MD

DIA

L F0

SH

UTT

ER

FU

LLD

3R15

VS

UB

D3R

0VM

OD

E D

IAL1

PO

WE

R O

N L

CM

D D

IAL

R0

BA

CK

BAT

+D

GN

D

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32

FP70

03

ECM

LIN

MIC

GND

STTX

DP

W E

XTS

TB5R

0VS

TRTT

LE

XT

STB

TR

GR

EC

ON

LFD

IAL

LED

KC

MD

DIA

L F1

SH

UTT

ER

HA

LFLE

D P

WR

OU

TLE

D U

SB

WIF

IM

OD

E D

IAL0

PO

N O

N L

CM

D D

IAL

R1

D G

ND

NCNT STB DET EXTSTB5R0V EXTSTB5R0V

STRTTLSTTXD

NCSTXSTXNC

MIC GNDECM LIN

D GNDWIFI CLKFI RESET

D3R5VIFI DAT3IFI DAT1D GND D3R15V

ISACC SDISACC SCKD GNDYRO REF GY3R0V

GYRO DOGYRO SCK GYRO CS

135791113151719212325272931

G WIFI CLKWIFI RESETPW D3R5VWIFI DAT3WIFI DAT1

D GNDPW D3R15V

S BISACC SDIS BISACC SCK

D GNDG GYRO REFPW GY3R0V

OIS GYRO DOOIS GYRO SCK

282624222018161412108642

2927252321191715131197531

FP5301D GNDD GND

PW D3R5VWIFI CMDWIFI DAT2WFI DAT0

PW D3R15VS BISACC IRQS BISACC SDOS BISACC CS

D GNDG GYRO OUT

PW VDD33OIS GYRO DIOIS GYRO CS

D GNDD3R15VD3R5V

THERMOSTB CHG STRT

UNREG GNDUNREG GNDUNREG GNDUNREG GND

NCUNREGUNREGUNREGUNREG

282624222018161412108642

2927252321191715131197531

FP8101D GNDD GND

LED AF OUTBAT D

STB CHG DETINT STB TRGUNREG GNDUNREG GNDUNREG GNDUNREG GND

UNREGUNREGUNREGUNREGUNREG

LAM

P+

LAM

P+

LAM

P+

NC

NC

LAM

P-

LAM

P-

LAM

P-

NC

NC

TRG

1st

NC

NC

TRG

GN

D

28 26 24 22 20 18 16 14 12 10 8 6 4 2

29 27 25 23 21 19 17 15 13 11 9 7 5 3 1

FP81

02LA

MP+

LAM

P+LA

MP+

NC NCLA

MP-

LAM

P-LA

MP-

NC NCTR

G 1

stTR

G 1

stNC

TRG

GND

TRG

GND

20 22 24 26

21 23 25 27

STB

CH

G D

ET

BAT

DLE

D A

F O

UT

D G

ND

THE

RM

OD

3R5V

D3R

15V

D G

ND

SPEAKER

4321

BAT -BAT DET

BAT THERMOBAT +

P8101

BATTERY

FP70011234

CMD DIAL R1D GND

PON ON LCMD DIAL R0

REAR DIALUNIT

RL8104RL8102 RL8101

RL8103

AF LED P.C.B.

FLASH P.C.B.

MAIN-FLASH FPC

MAIN GYRO FPC

P FPC

FLASH

FLASH FPC

FP85

014 3 2 1

WIF

I AN

TW

IFI A

NT

WIF

I AN

TW

IFI A

NT

Wi-Fi FPC

GYRO/WIFI P.C.B.(FOIL SIDE)

BATTERY P.C.B.(COMPONENT SIDE)

: (FOIL SIDE)

REAR PLATE UNIT

FRONT CASE UNIT

FLASH UNIT

67

13 Wiring Connection Diagram13.1. Interconnection Diagram

GNDSD0DA0MSD0DA1P

GNDSD0DA2MSD0CAP

GNDSD0DA3MSD0DB3P

GNDSD0CBMSD0DB2P

GNDSD0DB1MSD0DB0P

GNDIS SCKIS CS

IS PWR ON3GND

GNDSD0DA0P

GNDSD0DA1MSD0DA2P

GNDSD0CAMSD0DA3P

GNDSD0DB3MSD0CBP

GNDSD0DB2MSD0DB1P

GNDSD0DB0M

GNDIS SDO

IS PWR ON2IS THERMO

GND

GNDX1DR-GND

VDDDMVDD12D3R5VD5R2V

PW -0R95VHD

GNDYHO+X1HO-X1HI-

X2HO+Hall IN+

CLK27 IS FCKYDR-

X2DR+GNDGND

13579111315171921232527293133353739

1357911131517192123252729313335373941

2468

101214161820222426283032343638

2468

10121416182022242628303234363840

FP3501

FP3502

M DRIVE CTLSHUT MT1 BSHUT MT2 BSHUT PI IN1

GNDSHUT DACOUT1SHUT DACOUT2

GNDGND

PW SHUT9R0VPW SHUT9R0VPW SHUT9R0V

GNDSHUT MT1 ASHUT MT2 ASHUT PI K

SHUT PI IN2SHUT DACOUT1SHUT DACOUT2

GNDGNDGND


135791113151719212325

2468

1012141618202224

FP9002

PW SHUT9R0VPW SHUT9R0V

GNDGNDGND

SHUT DACOUT2SHUT DACOUT1

SHUT PI IN2SHUT PI K

SHUT MT2 ASHUT MT1 A

GND


GNDGND

SHUT DACOUT2SHUT DACOUT1

GNDSHUT PI IN1SHUT MT2 BSHUT MT1 BM DRIVE CTL

GND

135791113151719212325

24681012141618202224

FP9402

GNDX1DR+VDDDMVDD12D3R5VD3R5V

D3R15VIS PSV

VDYHI-YHO-

X1HO+X2HO-X2HI-GNDGNDYDR+X2DR-SSWF

D GNDHALL VCC

NCPW EXTSTB5R0V

NCSTRXD

NCNCSTXNCNC

ECM RINMIC GND

135791113151719212325

2468

1012141618202224

FP7002

IPWPW

GNDPW D3R15VPW D3R15V

PW UNREG SYSLCD BLT

RESTSP SDA

SCLGND

DB9(Cb1/Cr1)DB11(Cb3/Cr3)DB13(Cb5/Cr5)DB15(Cb7/Cr7)

DB1(Y1)DB3(Y3)DB5(Y5)DB7(Y7)

PCLKHSYNC

GND

39373533312927252321191715131197531

3836343230282624222018161412108642

FP7201

GNDPW D3R15V

PW UNREG SYSPW D1R8V

TSP INTTSP SCK

SDO(MOSI)CSX

DB8(Cb0/Cr0)DB10(Cb2/Cr2)DB12(Cb4/Cr4)DB14(Cb6/Cr6)

DB0(Y0)DB2(Y2)DB4(Y4)DB6(Y6)

GNDGND

VSYNC

GN

DC

LOC

KH

SY

NC

NR

ES

ET

VC

C(1

.8V

)V

CC

(1.8

V)

AVC

C(5

V)

DB

14(C

b6/C

r6)

DB

12(C

b4/C

r4)

DB

10(C

b2/C

r2)

DB

8(C

b0/C

r0)

DB

6(Y

6)D

B4(

Y4)

DB

2(Y

2)D

B0(

Y0)

SD

AG

ND

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32

FP93

02

GND

VIO

Sel

ial(3

.3V)

VCCX

(3.3

V)VS

YNC

VCC(

1.8V

)AV

CC(5

V)DB

15(C

b7/C

r7)

DB13

(Cb5

/Cr5

)DB

11(C

b3/C

r3)

DB9(

Cb1/

Cr1)

DB7(

Y7)

DB5(

Y5)

DB3(

Y3)

DB1(

Y1)

SCL

GND

G WIPWWW

PWS BS BI

G GPW

OISOIS OIS

24681012141618202224262830

FP9006

D GNDD GND

PW D3R5VWIFI CMDWIFI DAT2WIFI DAT0

PW D3R15VS BISACC IRQS BISACC SDOS BISACC CSGYRO GND

G GYRO OUTPW VDD33

OIS GYRO DIOIS GYRO CS

FP90

0332 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2

33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1

EC

M R

INM

IC G

ND

STR

XD

PW E

XSTB

5R0V

PW E

XSTB

5R0V

EX

T S

TB D

ET

INT

STB

DE

TFD

IAL

LED

AC

MD

DIA

L F0

SH

UTT

ER

FU

LLP

W D

3R15

VS

UB

D3R

0VM

OD

E D

IAL1

PO

WE

R O

N L

CM

D D

IAL

R0

BA

CK

BAT

+

MIC

GN

DE

CM

LIN

MIC

GN

DS

TTX

DPW

EXS

TB5R

0VS

TRTT

LE

XT

STB

TR

GR

EC

ON

LFD

IAL

LED

KC

MD

DIA

L F1

SH

UTT

ER

HA

LFLE

D P

WR

OU

TLE

D U

SB

WIF

IM

OD

E D

IAL0

PO

N O

N L

CM

D D

IAL

R1

D G

ND

FP90

052 4 6 8 10 12 14 16 18

1 3 5 7 9 11 13 15 17 19

UN

RE

GU

NR

EG

UN

RE

GU

NR

EG

UN

RE

G G

ND

UN

RE

G G

ND

UN

RE

G G

ND

UN

RE

G G

ND

INT

STB

TR

G

UN

RE

GU

NR

EG

UN

RE

GU

NR

EG

NC

UN

RE

G G

ND

UN

RE

G G

ND

UN

RE

G G

ND

UN

RE

G G

ND

STB

CH

G S

TRT

FP900421191715131197531

2018161412108642

LEN4R2VLEN4R2VLEN4R2V

GNDGNDGNDGND

LSRSTLSL2BLSCKLSLDP

LEN4R2VLEN4R2VLEN4R2V

GNDGNDGND

LSDETLSB2LLSDIOLSB2A

FP90

07D

GN

DH

ALL

VC

CLC

D O

PE

N D

ET

RE

AR

KE

YIN

1R

EA

R K

EY

IN2

CR

OS

S K

EY

ING

SP

PO

GG

SP

NE

GR

EA

R T

HE

RM

OD

GN

D

1 2 3 4 5 6 7 8 9 10

FP9001

24681012141618202224262830323436384042444648505254565860

13579

1113151719212325272931333537394143454749515355575961

GNDI2C SCK

GNDHSYNCPCLK

D7D5D3D1D15D13D11D9

GNDLCD BLTMON CS

MON SDOTP INT

MON RESPW D1R8VPW D3R15V

PW UNREG SYSPW D3R5V

PW EVF1R8VPW EVF1R8V

GNDGNDGND

PW VDD33SHUT THERMO

GND

GNDI2C SDAVSYNC

GNDGNDD6D4D2D0D14D12D10D8

EVF POWERGND

MON SCKGND

EVF RESGND

PW D3R15VPW D3R15V

PW UNREG SYSPW HDMI5R0VPW EVF1R8VPW EVF1R8V

G EVF1R8V FBLPSW

PW VDD33GNDGND

FP9401

24681012141618202224262830323436384042444648505254565860

135791113151719212325272931333537394143454749515355575961

GNDGNDGND

PW VDD33LPSW

G EVF1R8V FBPW EVF1R8VPW EVF1R8V

PW HDMI5R0VPW UNREG SYS

PW D3R15VPW D3R15V

GNDEVF RES

GNDMON SCK

GNDEVF POWER

D8D10D12D14D0D2D4D6

GNDGND

VSYNCI2C SDA

GND

GNDSHUT THERMO

PW VDD33GNDGNDGND

PW EVF1R8VPW EVF1R8V

PW D3R5VPW UNREG SYS

PW D3R15VPW D1R8VMON RES

TP INTMON SDOMON CSLCD BLT

GNDD9D11D13D15D1D3D5D7

PCLKHSYNC

GNDI2C SCK

1 2 3 4 5 6

I2C

SC

LP

W D

3R15

VI2

C S

DA

GN

DG

ND

LED

A (D

3R15

V)

FP94

03

654321

GNDGNDGND

LPSWLPSWLPSW

FP9404

FP99

01TH

ER

MO

GN

DS

HU

T TH

ER

MO

PI 2

C K

PI 2

C E

PI 2

C A

/CM

OT

2BM

OT

2BM

OT

2AM

OT

2AM

OT

1AM

OT

1AM

OT

1BM

OT

1BP

I 1C

A/C

PI 1

C K

PI 1

C E

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

GN

DV

SY

NC

GN

DG

ND

DB

6(Y

6)D

B4(

Y4)

DB

2(Y

2)D

B0(

Y0)

DB

14(C

b6/C

r6)

DB

12(C

b4/C

r4)

DB

10(C

b2/C

r2)

DB

8(C

b0/C

r0)

CS

XS

DO

(MO

SI)

TSP

SC

KTS

P IN

TP

W D

1R8V

PW

UN

RE

G S

YS

PW

D3R

15V

GN

D

39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1

38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2

FP93

01

GND

HSYN

CPC

LKDB

7(Y7

)DB

5(Y5

)DB

3(Y3

)DB

1(Y1

)DB

15(C

b7/C

r7)

DB13

(Cb5

/Cr5

)DB

11(C

b3/C

r3)

DB9(

Cb1/

Cr1)

GND SC

LTS

P SD

ARE

SLC

D BL

TPW

UNR

EG S

YSPW

D3R

15V

PW D

3R15

V

FP72

03

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61

GN

DC

21P

C22

PC

31M

C32

PV

GL

C41

MC

42P

AV

DD

LV

SN

VS

WP

VC

OM

DC

LED

PW

MH

SY

NC

GN

DD

B6(

Y6)

DB

4(Y

4)D

B2(

Y2)

DB

0(Y

0)D

B14

(Cb6

/Cr6

)D

B12

(Cb4

/Cr4

)D

B10

(Cb2

/Cr2

)D

B8(

Cb0

/Cr0

)S

CL

DIN

(MO

SI)

I2C

SC

L(TP

)IN

TFV

DD

VH

SP

GN

DG

ND

C21

MV

GH

C22

MC

31P

C32

MC

41P

C42

MV

CI(3

.1V

)V

SW

NV

SP

TXH

VD

DV

SY

NC

PC

LKD

B7(

Y7)

DB

5(Y

5)D

B3(

Y3)

DB

1(Y

1)D

B15

(Cb7

/Cr7

)D

B13

(Cb5

/Cr5

)D

B11

(Cb3

/cr3

)D

B9(

Cb1

/Cr1

)C

SX

NC(D

OUT

/MIS

O)

I2C

SDA(

TP)

RESX

IOVC

C1(1

.9V)

VRF

AVDD

GND

1234

CA LCDCA LCD

AN LCD(18.0V)AN LCD(18.0V)

FP7202

LCD

LCD FPC

LENS UNIT

MOUNT BASE UNIT

(LENS CONTACT)

(SHUTTER)

IS P.C.B.

ISP FPC ISS FPC

LENS RELEASE FPC PLATE

(SLLK)SLLK FPC UNIT

SHUTTER FPC

MAIN-SUB FPC

MAIN-TO

EYE SENSORFPC

LVF DISPLAYPANEL

LVF FPC

LVF UNIT

STEREOMICROPHONE

HOT SHOE FPC

HOT SHOE

(SSWF)SSWF FPC

LENS CAPACITOR

MAIN P.C.B.(FOIL SIDE)

LCD IF FPC(FOIL SIDE)

SUB P.C.B.(FOIL SIDE)

TOP P.C.B.(FOIL SIDE)

LCD UNIT

IMAGE SENSOR UNIT

14 Schematic DiagramPlease click the radio button for “Diagrams II / Parts List” on the menu bar in XML Service Manual.If you want to print, please click the icon button for “Print” on the icon bar and select the item.

15 Printed Circuit BoardPlease click the radio button for “Diagrams II / Parts List” on the menu bar in XML Service Manual.If you want to print, please click the icon button for “Print” on the icon bar and select the item.

16 Exploded View and Replacement Parts ListPlease click the radio button for “Diagrams II / Parts List” on the menu bar in XML Service Manual.If you want to print, please click the icon button for “Print” on the icon bar and select the item.

68

digital camera/body/lens kit/double zoom lens kit model … · digital camera/body/lens kit/double...

Documents