diffusion in porous media

104
Modern Methods in Heterogeneous Catalysis Lectures at Fritz-Haber-Institut 28.11.2008 Diffusion in Porous Media Diffusion in Porous Media Cornelia Breitkopf TU Bergakademie Freiberg for personal use only

Upload: ngohanh

Post on 03-Jan-2017

251 views

Category:

Documents


29 download

TRANSCRIPT

Page 1: Diffusion in Porous Media

Modern Methods in Heterogeneous Catalysis

Lectures at Fritz-Haber-Institut

28.11.2008

Diffusion in Porous MediaDiffusion in Porous Media

Cornelia Breitkopf

TU Bergakademie Freiberg

for personal use only

Page 2: Diffusion in Porous Media

Dimensions in Heterogeneous Catalysis

Page 3: Diffusion in Porous Media

Importance of transport for catalysis

• Material and energy balances are required for both thefluid, which occupies the interstitial region betweencatalyst particles, and the catalyst particles, in which thereactions occur

• Determination of rate limiting steps to ensure which stepacts to influence the overall rate of reaction in the pellet

Interaction of chemical reaction and transport processes

MACROKINETICS

Page 4: Diffusion in Porous Media

Outline

• Introduction– Porosity (definition, IUPAC)– Diffusion (laws, effective quantities, Knudsen diffusion, examples)– General transport equations for gases

• External mass transfer processes– Effectiveness factor, dimensionless quantities (Re, Sc)

• Internal mass transfer processes– Thiele modulus, case studies

• Influence of transport on– Activation energy, Reaction order, Selectivity

• Examples, experimental evaluation• Summary

Page 5: Diffusion in Porous Media

Recommended Literature

• R. Byron Bird et al. Transport Phenomena. J. Wiley 2007

• C.H. Bartholomev, R. J. FarrautoFundamentals of industrial catalytic processes. AIChe 2006

• M. Baerns, H. Hofmann, A. Renken. Chemische Reaktionstechnik, LB der Technischen Chemie, Bd. 1,Wiley-VCH, 2002.

• M. Jakubith. Grundoperationen und chemische Reaktionstechnik. Einführung in die Technische Chemie. Wiley-VCH 1998.

• Fixed-Bed Catalytic Reactors. Nob Hill Publ. 2004. (see web)• IUPAC: Pure & Appl.Chem. 66 (1994) 1739.• Lexikon Chemie, Brockhaus ABC. VEB F.A. Brockhaus Verlag,

Leipzig1987.• Technische Anorganische Chemie. Deutscher Verlag für Grundstoffindustrie

GmbH, Leipzig1990.• I.I. Ioffe, L.M. Pissmen. Heterogene Katalyse, Chemie und Technik,

Akademie-Verlag Berlin, 1975.

Page 6: Diffusion in Porous Media

Porosity – Background information

Page 7: Diffusion in Porous Media

Porous materials in nature and industry

• Porous materials: sand stone, porous rock, filter paper, nano tubes…

• Main feature: cavities in a solid matrix• Cavities can be partly or fully connected• Accessible for gases

• Porosities are often desired and of importance in medicines, membranes, sorbents, ceramics, and catalysts

Page 8: Diffusion in Porous Media

Pore types

• Pressing of support material leads to a network of micro-/meso-porous and macroporous areas: powder particlesare micro-/mesoporous, pores between particles build up a macroporous network

• Types of pores– open pores: surface ~, column ~, hollow ~– isolated pores: inclusion ~– see IUPAC

Page 9: Diffusion in Porous Media

IUPAC - Definitions

• Porous solid: a solid with pores, i.e. cavities, channels orinterstices, which are deeper than they are wide

• Pore size: (generally pore width): the distance betweentwo opposite walls of the pore– Micropores (< 2 nm), – Mesopores (2-50 nm) – Macropores (> 50 nm)

• Porosity ε: ratio of the total pore volume VP to theapparent volume V of the particle or powder (excludinginterparticle voids)

Page 10: Diffusion in Porous Media

IUPAC - Quantitative description of porosity

• Value of the fraction depends on the method used to determine

– the apparent volume V, which excludes interparticlevoids (geometrical determination, fluid displacement)

– the pore volume VP (adsorption and capillarycondensation…)

• Some methods have only access to „open pores“ (i.e. the methods using a fluid) whereas others may also have access to „closed pores“ (i.e. methods usingradiation)

Page 11: Diffusion in Porous Media

Pore properties - Structure

• Pore structure is a strong function of the preparationmethod, and catalysts can have pore volumes ranging from 0.1-1 cm3/g pellet

• Pores can be the same size or there can be a bimodaldistribution of two different sizes

• Pore sizes can be as small as molecular dimensions(nm) or as large as several millimeters

Page 12: Diffusion in Porous Media

Types of porosity

• Difference between bed porosity and particle porosity• Bed porosity (or void fraction) εB is defined as the

volume of voids per volume of reactor• The pellet void fraction or porosity is denoted by ε and

ε = ρP * Vg (ρP effective particle density, Vg pore volume)

Jakubith

Page 13: Diffusion in Porous Media

Diffusion – Background

Page 14: Diffusion in Porous Media

Diffusion – In general

• …is the transport of mass in gases, liquids and solidsunder the influence of a concentration gradient

• …proceeds spontaneously due to microscopicmovement of mass

• … is an irreversible process which leads to an increasein entropy and is only reversible by supply of work

Page 15: Diffusion in Porous Media

Diffusion – In special

• …mechanisms differ for gases/liquids and solids

• …for gases/liquids: statistical movement according to T

• …for solids: different mechanisms possible: i) direct exchange of lattice placesii) movement via interstitial lattice sitesiii) movement via lattice vacanciesiv) movement via lattice defects or on the grain surfacev) exchange of sites on the crystal surface

Page 16: Diffusion in Porous Media

Examples - Diffusion in technical solids

• High temperature inorganic reactions

TC Anorg. Chemie

Page 17: Diffusion in Porous Media

Diffusion - quantitatively

• …generally increases with temperature and decreaseswith increasing density

• …the equilibration takes– minutes for gases– days/weeks for liquids– with measurable rate only close to the melting point

• …characteristic quantity: diffusion coefficient

• …can be described as molecular transport quantity or as effective quantity

Page 18: Diffusion in Porous Media

Examples - Diffusion coefficients

D [cm2/s] T [K]H2 in O2 0.78 298N2 in O2 0.19 298H2O vapour in air 0.23 298CH3OH in water 1.2*10-5 298Sugar in water 0.5*10-5 298Au in Cu 2.1*10-11 1023Fe in Al 6.2*10-14 62336Cl- in AgCl 3.2*10-16 623

Lexikon Chemie

Page 19: Diffusion in Porous Media

From „Transport Phenomena“

Page 20: Diffusion in Porous Media

Transport by Diffusion

Page 21: Diffusion in Porous Media

General view to transport equations for gases

Transport

Mass Heat Energy

⎟⎠⎞

⎜⎝⎛−=

dzdcDj in ⎟

⎠⎞

⎜⎝⎛−=

dzdTjQ λ ⎟⎟

⎞⎜⎜⎝

⎛−=

dyduj z

P η

Fourier´s Law Newton´s LawFick´s Law

Page 22: Diffusion in Porous Media
Page 23: Diffusion in Porous Media
Page 24: Diffusion in Porous Media

Transport of mass - Diffusional laws (gases)

• Concentration gradient is stationary : Fick´s First Law

• Concentration gradient is not stationary : Ficks´s Second Law

important for diffusion in porous catalysts !

⎟⎠⎞

⎜⎝⎛−=

dzdcDj in

⎥⎦⎤

⎢⎣⎡

∂∂

∂∂

=⎟⎠⎞

⎜⎝⎛∂∂

zcD

ztc i

iz

i

Page 25: Diffusion in Porous Media

Diffusion - Special diffusion phenomena

• Molecular diffusion

• Knudsen diffusion

• Surface diffusion– lateral diffusion– not of technical importance

• Configurational diffusion– pore diameter within molecular dimensions (0.3-1 nm) as for

zeolites– diffusion coefficients are smaller by some orders of magnitude

Page 26: Diffusion in Porous Media

Molecular diffusion coefficient

• Molecular diffusion coefficient for gases

• DM during catalytic process nearly constant; reaction rate constant changes exponentially !

lengthpathfreemean...;velocityaverage...v;v31DM λλ=

pdkT

mkT

32D 2

21

M π⎟⎠⎞

⎜⎝⎛π

= 223

M d1~,

m1~,

p1~,T~D

Page 27: Diffusion in Porous Media

Molecular diffusion coefficient

• Kinetic gas theory delivers only inaccurate values fortransport coefficients

• Binary diffusion coefficients for mixtures of gases (up to p ≈ 2.5*106 Pa) (Hirschfelder/Curtiss/Bird)

gsABD

122

,,

,,3

,2

001834.0 −

Ω

+

= smp

MMMM

TD

DAB

BrAr

BrAr

gsAB σ

constantsforcetorespectwithintegralCollisionΩBandAgasesoffactorcollisionAverageσ

BandAmoleculesofmassesmolecularRelativeM,M[bar] Pressure p

[K]eTemperaturT

D

2AB

Br,Ar,

Page 28: Diffusion in Porous Media

Knudsen diffusion coefficient

• With decreasing pore diameter (or decreasing pressure), the pore diameter is smaller than the mean free pathlength λ >> dp: DKn …Knudsen diffusion coefficient

• Depends not on pressure !

diameterpore...d;velocityaverage...v;dv31D ppKn =

p21

Kn d~,M1~,T~D

MRT8d

31D pKn π

=

Page 29: Diffusion in Porous Media

Diffusion in porous materials

• For dp = const. and pressure decrease: transition frommolecular diffusion to Knudsen diffusion

• Transition is not clearly defined; both equations apply

• Catalysts: irregular network of pores – effective D• For very heterogeneous pore size distributions the term

„effective D“ is not valid – complex models necessary

KnM* D

1D1

D1

+=

Page 30: Diffusion in Porous Media

Effective diffusivities

DDeff τε

=• Use of porosity and tortuosity factor

Fixed-bed Catal.

Page 31: Diffusion in Porous Media

Diffusion - Current interest in science

• 10 000 paper/year dealing with diffusion phenomena• Multitude of topics

• International Conferences:– 5th International Conference on Diffusion in Solids and Liquids

Page 32: Diffusion in Porous Media

Literature examples

Page 33: Diffusion in Porous Media

…continued

Page 34: Diffusion in Porous Media
Page 35: Diffusion in Porous Media
Page 36: Diffusion in Porous Media
Page 37: Diffusion in Porous Media
Page 38: Diffusion in Porous Media
Page 39: Diffusion in Porous Media
Page 40: Diffusion in Porous Media

Transport problems in catalysis

Page 41: Diffusion in Porous Media

Transport and catalysis

• One part of the catalytic cycle is the transport of reactants to the active surface

• Typical heterogeneous processes proceed at thesurface of solids or porous particles, which aresurrounded by gas or liquid

• If the chemical reaction proceeds very fast, the overallrate may be controlled by the transport of reactand fromthe fluid to the external surface of the catalyst particle orby diffusion inside the pores of the catalyst particle

Page 42: Diffusion in Porous Media

From „Fundamentals in industrial…

Page 43: Diffusion in Porous Media

Transport regimes

Transport

External Internal

Diffusion in poresDiffusion to exteriorsurface of particle

Page 44: Diffusion in Porous Media

Rates in the catalytic cycle

Catalytic circle

Chemicalreactions

Physicalprocesses

• ratediffusion >> ratechemical reaction : no influence on overall rate• substrate concentration in pores and on catalyst surface =

gas concentration

• ratediffusion ≈ ratechemical reaction : incomplete mass transfer, thus decrease in reaction rate

Page 45: Diffusion in Porous Media

External or internal mass transfer control ?

To get insights in kinetics of chemical reactions theinfluence of diffusion on the reaction has to be known

and to be eliminated

Criteria for diffusional influences ?

Page 46: Diffusion in Porous Media

From „Fundamentals in industrial…

Page 47: Diffusion in Porous Media

External mass transfer processes

Page 48: Diffusion in Porous Media

External mass transfer - Model

• Influence of mass transfer: yes/no ? – coupling of flux equations for mass transfer (and heat

transfer) with reaction rate equation

Model:• System at stationary conditions• Main quantities:

– gas phase (bulk) concentration cg

– concentration at exterior surface cs

(see Baerns)

Page 49: Diffusion in Porous Media

External mass transfer – Rate equation

• Effective rates for transfer and reaction

• Calculation of cs possible

areasurfacespecifica

tcoefficientransferk)cc(akr gs,1g,1geff −=

akkckr ss,1m

eff ==

s,1m

s,1g,1g ck)cc(ak =−

akk1

cc

g

g,1s,1

+=

Page 50: Diffusion in Porous Media

External mass transfer – Effective rate

• for m =1

• Case studies:

mass transfer is fast compared to chemical reaction,no concentration gradient in film

g,1

g

s,1m

eff ca

kk1

kckr+

==

1ak

k

g

<<

g,1eff ckr =

Page 51: Diffusion in Porous Media

External mass transfer – Da number

• Damköhler number II: for any m

ratio of rate without mass transfer limitation (c1,s=c1,g) to rate with maximal mass transfer limitation (c1,s 0)

• Definition of new quantity for the description of catalystperformance

g,1g

g,1m

cakckDaII=

Page 52: Diffusion in Porous Media

External mass transfer – Effectiveness factor

• Definition of external effectiveness factor ηext for a catalyst

ratio of reaction rate with diffusion limitation to reactionrate without diffusion limitation(case for first order reaction)

• ηext for higher reaction order more complicated(see textbook)

DaII11

ckck

rr

g,1

g,1effeffext +

===η

Page 53: Diffusion in Porous Media

External mass transfer – Effectiveness factor

• External effectiveness factor ηext

depending on m

• Estimation of external transportinfluence possible by usingexperimental quantities

rreff

ext =η

Page 54: Diffusion in Porous Media

External mass transfer - Criteria

µ=

vdRe p

• Film around particle depends on flow conditions: laminar (or turbulent)

• Dimensionless Reynolds number Re

dp…particle diameterv …velocity of gasµ …viscosity of gas

• Correlation between mass transfer coefficient kg and reaction rate; for kinetic regime: transfer >> rate

Page 55: Diffusion in Porous Media

External mass transfer - Criteria

• Check flow profile of reactordR …reactor diameterdp …particle diameter

• Fixed bed reactor catalyst in powder form• Re > 2 no back mixing effects• Re, Sc (Schmidt) as dimensionless quantities• Description of flux as function of Sc number

30>p

R

dd

M

3/2

M

gD D

ScScv

pk(Re)fj µ

===

Page 56: Diffusion in Porous Media

Experimental check

• Fixed bed reactor:for the condition of a constant residence time increase of linear velocity of the fluid around the particles until theresulting rate keeps constant

no influence of external transfer

! residence time decreases with increasing velocity of fluid, increase the bed height to compensate this

Page 57: Diffusion in Porous Media

Internal mass transfer processes

Page 58: Diffusion in Porous Media

Internal transport - Pore diffusion

• Transport of reactant through porous pore systemto the active centres

• Diffusion is slow process thus the transport limits conversion

• Simple approximation of pore diffusion

Page 59: Diffusion in Porous Media

Pore diffusion - Rates

1. Assumption:• Catalyst pore with cross section S and length l• Reaction in pore is 1st order : r = k*c

• Reaction rate R related to active surface S (V = S*l)• Reaction rate rV in pore volume

c*k*lSRr*l v −==

see Jakubith

Page 60: Diffusion in Porous Media

Pore diffusion – Diffusion coefficient

2. Assumption:• Diffusion coefficient inside the pore differs from diffusion

coefficient Dgs

• Correction by tortuosity factor and porosityeffective diffusion coefficient

first assumption, if no information availablegsgs

eff D101D ≈

Page 61: Diffusion in Porous Media

Pore diffusion – Mass balance

• General mass balance for one-dimensional, steady-state case, reaction is 1st order

• Solution of differential equation with help of dimensionless variables Γ and ζ

c0 concentration in free gas spacel pore length

0ckdz

cdD 2

2

eff =−

0cc

lz

Page 62: Diffusion in Porous Media

Pore diffusion – Thiele modulus

• Dimensionless mass balance

• Quotient is a dimensionless term

• Thiele modulus

0cckc

lzd

ccd

lc

D0

020

2

20

eff =−

⎟⎠⎞

⎜⎝⎛

0D

kldd

eff

2

2

2

=Γ−ζΓ

eff

22

Dkl

effDkl=ϕ

Page 63: Diffusion in Porous Media

Thiele Modulus ϕ

• The single dimensionless group appearing in the modelis referred to as the Thiele number or Thiele modulus in recognition of Thiele´s pioneering contribution to thisarea:E.W. Thiele. Relation between catalytic activity and size of particle. Ind. Eng. Chem. 31(7) (1939) 916-920.

• In his original paper, Thiele used the term „modulus“ to emphasize that this then unnamed dimensionless groupwas positive. Later when Thiele´s name was assigned to this dimensionless group , the term modulus was retained.

Page 64: Diffusion in Porous Media

Pore diffusion – Thiele modulus

• Thiele modulus

• New form of differential equation for mass balance

• Solve with appropriate initial and boundary conditions

ratediffusionratereaction

Dkleff

==ϕ

Γϕ=ζΓ 22

2

dd

Page 65: Diffusion in Porous Media

Pore diffusion – Solving of mass balance

• Boundary conditions

1. for z = 0 , c = c0 or for ζ = 0 , Γ = 12. for z = l , dc/dz = 0 or for ζ = 1 , dΓ/dζ = 0

• Solution of differential equation by exponential approximation

decrease of cdue to reaction

freegas space

Page 66: Diffusion in Porous Media

Pore diffusion – Case studies

• Concentration of reactant inside the pore

• with increasing temperature the Thiele modulus increasesbecause of and

• Reactant converts already at z/l << 1

ϕ

−ϕ=

ϕζ−ϕ

=Γcosh

)lz1(cosh

ccor

cosh)1(cosh

0

effDkl=ϕ ⎥⎦

⎤⎢⎣⎡−=

RTE

expkk A0

It is of technical importance to find the temperaturewhere pore diffusion starts to influence the reaction !

Page 67: Diffusion in Porous Media

Pore diffusion – Case studies

ϕ

−ϕ=

ϕζ−ϕ

=Γcosh

)lz1(cosh

ccor

cosh)1(cosh

0

- with ϕ ≥ 3 the reactantcan not reach the interior of thepore- no full utilization of the internalsurface of the catalyst

Page 68: Diffusion in Porous Media

Pore diffusion - Criteria

• Thiele modulus

• Criteria:– ϕ << 1

• chemical reaction is rate-limiting• diffusion is fast, reactand can enter the pores of

the catalyst and the concentration of the reactandis constant for the whole catalyst volume

– ϕ >> 1• limitation of overall rate by diffusion of reactand in

the pores• inside the pores the reactand converts fast• concentration of reactand decreases already close

to the boundary layer

effDkl=ϕ

Page 69: Diffusion in Porous Media

Internal transfer - Effectiveness factor η

• Reaction rate rs

• Effectiveness factor is defined as

• max. reaction rate is connected with c0

vs r*lr =

ratereaction.maxratereaction

max,s

s

rr

0

l

0

max,s

s

clk

dz)z(ck

rr ∫

==η

Page 70: Diffusion in Porous Media

Effectiveness factor η - Case studies

• Effectiveness factor is a dimensionless pellet productionrate that measures how effectively the catalyst is beingused.

• For η near unity, the entire volume of the pellet isreacting at the same high rate because the reactant isable to diffuse quickly through the pellet.

• For η near zero, the pellet reacts at low rate. Thereactant is unable to penetrate significantly into theinterior of the pellet and the reaction rate is small in a large portion of the pellet volume.

Page 71: Diffusion in Porous Media

• with solution function for Γ (see results for pore diffusion)

two characteristic regimes

Effectiveness factor η - Case studies

dzcoshl

)l/z1(coshl

0∫ ϕ

−ϕ=η

ϕϕ

=ηtanh

Page 72: Diffusion in Porous Media

• for ϕ ≤ 0.3 , regime of reaction control

• for ϕ ≥ 0.3 , regime of pore diffusion control

Effectiveness factor η - Case studies

ϕ≈η

1

1≈η

Page 73: Diffusion in Porous Media

• Solution depends on characteristic length (volume-tosurface ratio)

• Characteristic length differs for cylinder, sphere or slab; different analytical solutions

Effectiveness factor - Geometry of pores

Fixed-bed catal. r.

Page 74: Diffusion in Porous Media

Effectiveness factor - Geometry of pores

• functional forms (see table) are quite different, butsolutions are quite similar

• identical asymptotes for small and large ϕ

Page 75: Diffusion in Porous Media

From „Fundamentals in industrial…

Page 76: Diffusion in Porous Media

Examples (see Baerns)

Page 77: Diffusion in Porous Media
Page 78: Diffusion in Porous Media
Page 79: Diffusion in Porous Media
Page 80: Diffusion in Porous Media
Page 81: Diffusion in Porous Media

Influence of transport on the measurement of

Activation energiesReaction ordersSelectivities

Page 82: Diffusion in Porous Media

Apparent versus Intrinsic Kinetics

• Aim: determination of reaction order and rate constantfor a catalytic reaction of interest

• Assumption: nth-order reaction A B with• The values of „k“ and „n“ are called the intrinsic rate

constant and reaction order • Typical experiment: change concentration cA in the bulk

fluid, measure the rate as function of cA and find thevalues of the parameters „k“ and „n“ that best fit themeasurements

• The intrinsic values have to be distinguished from whatwe may estimate from experimental data !

nAckr =

Page 83: Diffusion in Porous Media

Apparent and Intrinsic Activation Energy

• Qualitative estimation of kinetic parameters underdifferent rate-limiting steps

• Arrhenius plot: ln (k*η) = f(1/T)

• ln (k*η) is the apparent rate constant related to theapparent activation energy EA,s

RTE

kln]k[ln s,A0 −=η

Page 84: Diffusion in Porous Media

Arrhenius plot – Regimes of control

1. kinetic regime

2. pore diffusionregime

3.mass transfer regime

Page 85: Diffusion in Porous Media

Arrhenius plot – Kinetic regime

• Thiele modulus ϕ is very small (ϕ <<)

The internal surface of catalyst pore is totally utilized

• η ≈ 1; see fig. η = f(ϕ)

• k*η ≈ k

As,A EE ≈

Page 86: Diffusion in Porous Media

Arrhenius plot – Pore diffusion regime

• Case study:

• η ≈ 1/ϕ; see fig. η = f(ϕ)

• ln (k*η) =ln k + ln η

• η = 1/ϕ and

effDkl=ϕ

⎥⎦

⎤⎢⎣

⎡−=η

effDkllnkln]*k[ln

Page 87: Diffusion in Porous Media

Arrhenius plot – Pore diffusion regime

⎥⎦

⎤⎢⎣

⎡−=η

effDkllnkln]*k[ln

effDln21llnkln

21]*k[ln +−=η

effs,A

0 Dln21lln

RT2E

kln21]*k[ln +−−=η

2EE A

s,A =

Page 88: Diffusion in Porous Media

Arrhenius plot – Mass transfer regime

• For high temperatures ϕ >> 1 and η << 1

• Reaction is only determined by diffusion through theboundary film layer

0E s,A ≈

Page 89: Diffusion in Porous Media

Arrhenius plot – Mass transfer regime

• transfer contributes to rate• for kga << k

• keff = kga

• kg is determined by D; D ~ T3/2 thus kg ~ T3/2; formal

• Eeff = EDiff• EDiff~ 5 kJ/mol

0E s,A ≈

ak1

k1

1k

g

eff

+=

⎟⎠⎞

⎜⎝⎛−≈

RT2E

expk effg

Page 90: Diffusion in Porous Media

Interpretation of criteria for EA

• The apparent activation energy EA,s of a heterogeneouscatalytic reaction decreases with increasing temperaturedue to the increasing diffusive resistance to EA,s= EA/2

• Further increase in temperature leads to a shift of theplace of reaction from the interior to the exterior of thecatalyst

• At high temperatures only the transport through theboundary layer determines the rate of reaction

• Way out ? - use of smaller particles• Disadvantages - pressure control in a fixed bed

- dispersion increase in a fixed bed

Page 91: Diffusion in Porous Media

Influence of transport on reaction order

• Catalytic reaction described by

• Determination of „n“ may be misleading, if external orinternal mass-transfer limitations exist due to η = f(c)

napp: 0 1 2nintr : 0.5 1 1.5

• Check for rate-limiting processes

nAckr =

Page 92: Diffusion in Porous Media

Influence of transport on selectivity

• Network of reactions (parallel, consecutive….)• Selectivity of desired product is of interest• See textbooks for case studies• Simple example: B

AC

if cA is limited, the first reaction is more influenced

k1

k2

2A11 ckr =

A22 ckr =

Page 93: Diffusion in Porous Media

Influence of transport on selectivity

• General approach: – set up of kinetic equations– determination of differential and integral selectivities

according to kinetic equations– formulation of effective quantities– examine influence of η, Da number …

Page 94: Diffusion in Porous Media

External and internal resistances – Biot n.

• Isothermal conditions• If the mass-transfer rate from the bulk fluid to the exterior

of the pellet is not high, then the boundary conditionshave to be changed

• Biot number or dimensionless mass-transfer coefficient

• Relation between internal and external diffusionresistance

• Bi >> 1: transport limited by diffusion in the pores

Drk

Bi pg=

Page 95: Diffusion in Porous Media

External and internal resistances – Biot n.

• Biot number or dimensionless mass-transfer coefficient

Drk

Bi pg=

Fixed-bed catal. r.

Page 96: Diffusion in Porous Media

External and internal resistances – Criteria

• Overall effectiveness factor ηsum is related to thetransport resistances in the film and in the pore

• Non-isothermal conditions: Weisz modulus, modifiedThiele modulus, Sherwood number Sh, Nusselt numberNu !

Bi31

12

k

sum ϕ+

η

Page 97: Diffusion in Porous Media

Experimental check

• For a porous catalyst the limiting effect of pore diffusionwould be decreasing if it is possible to reduce the lengthof the pores

• Practically: crush catalyst, grade into sizes; measurement of apparent rate depending on sizefractions; with decreasing size the apparent rate increases until a constant value is reached

• Check the external transport; both limitations may occursimultaneously

• Elegant way of separation of pore diffusion and microkinetics: use of single pellet diffusion reactor

Page 98: Diffusion in Porous Media

From „Fundamentals in industrial…

Page 99: Diffusion in Porous Media

From „Fundamentals in industrial…

Page 100: Diffusion in Porous Media
Page 101: Diffusion in Porous Media

Summary

Definition of porous systems

Definition of diffusion and diffusion coefficients

External transfer processesProduction rate via effectiveness factorCase studies with use of Re, DaII

Internal transfer processesMass balance for pore diffusionCase studies depending on Thiele modulus

Page 102: Diffusion in Porous Media

Summary

Influence of transport onApparent activation energyReaction orderSelectivity

Influence of both external and internal transferBiot number

Strategy to check for limiting processes: solve appropriate mass balance by use of dimensionlessnumbers

The system is investigated from the outside to the inside

Page 103: Diffusion in Porous Media

…Thanks for invitation and for attention!

Page 104: Diffusion in Porous Media

Diffusion constant and pore radius

• Diffusion constants in pores for pore diameters which arecomparable to substrate molecules

I Knudsen diffusionII potentials of opposite pore walls overlap thus the resulting

interaction of substrates and walls is effectively decreasedand the diffusion coefficient increases

III pore diameter is in the range of the substrate diameter; strongdependence of D from the effective substrate diameter

IIIIII

D

rpore