crystal structure and crystal geometry

367

Crystal Structures and Crystal Geometry

I t is possible to map the surfaces of conducting solids at the atomic level using aninstrument called the scanning tunneling microscope (STM). The STM allowsthe observation and manipulation of adsorbate molecules and chemical reactionson the atomic scale. This is accomplished by manipulating and monitoring a smallamount of current passing through the extremely small STM tip (single-atomtungsten nanotip). The current is amplified and used to measure the size of the gap

( IBM Corporation.)

C H A P T E R

smi02334_ch03.qxd 4/21/03 3:38 PM Page 67

68 C H A P T E R 3 Crystal Structures and Crystal Geometry

(b)(a)

c

b

Figure 3.1(a) Space lattice of ideal crystalline solid. (b) Unit cell showing latticeconstants.

1www.sljus.lu.se/stm/NonTech.html

between the nanotip and the atoms on the surface. The chapter-opening image is anexample of the resolution achieved using the STM technology.

Scientists discovered a new method for confining electrons to artificial struc-tures at the nanometer lengthscale. Surface state electrons on Cu(111) were con-fined to closed structures (corrals) defined by barriers built from Fe adatoms. Thebarriers were assembled by individually positioning Fe adatoms using the tip ofa low temperature scanning tunneling microscope (STM). A circular corral of ra-dius 71.3 Angstrom was constructed in this way out of 48 Fe adatoms.1

3.1 THE SPACE LATTICE AND UNIT CELLSThe physical structure of solid materials of engineering importance dependsmainly on the arrangements of the atoms, ions, or molecules that make up thesolid and the bonding forces between them. If the atoms or ions of a solid arearranged in a pattern that repeats itself in three dimensions, they form a solid thatis said to have a crystal structure and is referred to as a crystalline solid or crys-talline material. Examples of crystalline materials are metals, alloys, and someceramic materials.

Atomic arrangements in crystalline solids can be described by referring theatoms to the points of intersection of a network of lines in three dimensions. Sucha network is called a space lattice (Fig. 3.1a), and it can be described as aninfinite three-dimensional array of points. Each point in the space lattice hasidentical surroundings. In an ideal crystal the grouping of lattice points about anygiven point are identical with the grouping about any other lattice point in thecrystal lattice. Each space lattice can thus be described by specifying the atompositions in a repeating unit cell, such as the one heavily outlined in Fig. 3.1a.The size and shape of the unit cell can be described by three lattice vectors a, b,

smi02334_ch03.qxd 4/21/03 3:38 PM Page 68

3.2 Crystal Systems and Bravais Lattices 69

2August Bravais (18111863). French crystallographer who derived the 14 possible arrangements ofpoints in space.

and c, originating from one corner of the unit cell (Fig. 3.1b). The axial lengthsa, b, and c and the interaxial angles , , and are the lattice constants of theunit cell.

3.2 CRYSTAL SYSTEMS ANDBRAVAIS LATTICES

By assigning specific values for axial lengths and interaxial angles, unit cells ofdifferent types can be constructed. Crystallographers have shown that only sevendifferent types of unit cells are necessary to create all point lattices. These crys-tal systems are listed in Table 3.1.

Many of the seven crystal systems have variations of the basic unit cell. A. J.Bravais2 showed that 14 standard unit cells could describe all possible latticenetworks. These Bravais lattices are illustrated in Fig. 3.2. There are four basictypes of unit cells: (1) simple, (2) body-centered, (3) face-centered, and (4) base-centered.

In the cubic system there are three types of unit cells: simple cubic, body-centered cubic, and face-centered cubic. In the orthorhombic system all four

Table 3.1 Classification of Space Lattices by Crystal System

Crystal system Axial lengths and interaxial angles Space latticeCubic Three equal axes at right angles Simple cubic

a = b = c, = = = 90 Body-centered cubicFace-centered cubic

Tetragonal Three axes at right angles, two equal Simple tetragonala = b = c, = = = 90 Body-centered tetragonal

Orthorhombic Three unequal axes at right angles Simple orthorhombica = b = c, = = = 90 Body-centered orthorhombic

Base-centered orthorhombicFace-centered orthorhombic

Rhombohedral Three equal axes, equally inclined Simple rhombohedrala = b = c, = = = 90

Hexagonal Two equal axes at 120 , third axis Simple hexagonalat right anglesa = b = c, = = 90 , = 120

Monoclinic Three unequal axes, one pair not Simple monoclinicat right angles Base-centered monoclinica = b = c, = = 90 =

Triclinic Three unequal axes, unequally Simple triclinicinclined and none at right anglesa = b = c, = = = 90

smi02334_ch03.qxd 4/21/03 3:38 PM Page 69


c

c

ba

c

b

c

b

Monoclinic

c

TriclinicOrthorhombicHexagonalCubic

Figure 3.2The 14 Bravais conventional unit cells grouped according to crystal system. The dotsindicate lattice points that, when located on faces or at corners, are shared by otheridentical lattice unit cells.(After W. G. Moffatt, G. W. Pearsall, and J. Wulff, The Structure and Properties of Materials, vol. I: Structure,Wiley, 1964, p. 47.)

smi02334_ch03.qxd 4/21/03 3:38 PM Page 70

3.3 Principal Metallic Crystal Structures 71

(b) (c)(a)

Figure 3.3Principal metal crystal structure unit cells: (a) body-centered cubic, (b) face-centered cubic, (c) hexagonal close-packed.

31 nanometer = 109 meter.

types are represented. In the tetragonal system there are only two: simple andbody-centered. The face-centered tetragonal unit cell appears to be missing butcan be constructed from four body-centered tetragonal unit cells. The monoclinicsystem has simple and base-centered unit cells, and the rhombohedral, hexago-nal, and triclinic systems have only one simple type of unit cell.

3.3 PRINCIPAL METALLIC CRYSTALSTRUCTURES

In this chapter the principal crystal structures of elemental metals will be dis-cussed in detail. In Chap. 10 the principal ionic and covalent crystal structuresthat occur in ceramic materials will be treated.

Most elemental metals (about 90 percent) crystallize upon solidification intothree densely packed crystal structures: body-centered cubic (BCC) (Fig. 3.3a),face-centered cubic (FCC) (Fig. 3.3b) and hexagonal close-packed (HCP)(Fig. 3.3c). The HCP structure is a denser modification of the simple hexagonalcrystal structure shown in Fig. 3.2. Most metals crystallize in these dense-packedstructures because energy is released as the atoms come closer together and bondmore tightly with each other. Thus, the densely packed structures are in lowerand more stable energy arrangements.

The extremely small size of the unit cells of crystalline metals that are shownin Fig. 3.3 should be emphasized. The cube side of the unit cell of body-centeredcubic iron, for example, at room temperature is equal to 0.287 109 m, or0.287 nanometer (nm).3 Therefore, if unit cells of pure iron are lined up side byside, in 1 mm there will be

1 mm 1 unit cell0.287 nm 106 mm/nm = 3.48 10

6 unit cells!

smi02334_ch03.qxd 4/21/03 3:38 PM Page 71


Let us now examine in detail the arrangement of the atoms in the three prin-cipal crystal structure unit cells. Although an approximation, we shall consideratoms in these crystal structures to be hard spheres. The distance between theatoms (interatomic distance) in crystal structures can be determined experimen-tally by x-ray diffraction analysis.4 For example, the interatomic distance be-tween two aluminum atoms in a piece of pure aluminum at 20C is 0.2862 nm.The radius of the aluminum atom in the aluminum metal is assumed to be half theinteratomic distance, or 0.143 nm. The atomic radii of selected metals are listedin Tables 3.2 to 3.4.

3.3.1 Body-Centered Cubic (BCC) Crystal Structure

First, consider the atomic-site unit cell for the BCC crystal structure shown inFig. 3.4a. In this unit cell the solid spheres represent the centers where atoms arelocated and clearly indicate their relative positions. If we represent the atoms inthis cell as hard spheres, then the unit cell appears as shown in Fig. 3.4b. In this

4Some of the principles of x-ray diffraction analysis will be studied in Sec. 3.11.

Table 3.2 Selected Metals That Have the BCC Crystal Structure at Room Temperature(20C) and Their Lattice Constants and Atomic Radii

Metal Lattice constant a (nm) Atomic radius R* (nm)Chromium 0.289 0.125Iron 0.287 0.124Molybdenum 0.315 0.136Potassium 0.533 0.231Sodium 0.429 0.186Tantalum 0.330 0.143Tungsten 0.316 0.137Vanadium 0.304 0.132Calculated from lattice constants by using Eq. (3.1), R = 3a/4.

Table 3.3 Selected Metals That Have the FCC Crystal Structure at Room Temperature(20C) and Their Lattice Constants and Atomic Radii

Metal Lattice constant a (nm) Atomic radius R* (nm)Aluminum 0.405 0.143Copper 0.3615 0.128Gold 0.408 0.144Lead 0.495 0.175Nickel 0.352 0.125Platinum 0.393 0.139Silver 0.409 0.144Calculated from lattice constants by using Eq. (3.3), R = 2a/4.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 72


(a) (b) (c)

Figure 3.4BCC unit cells: (a) atomic-site unit cell, (b) hard-sphere unit cell, and(c) isolated unit cell.

a

4R3a

3 a 4R2a

Figure 3.5BCC unit cell showingrelationship between thelattice constant a andthe atomic radius R.

unit cell we see that the central atom is surrounded by eight nearest neighborsand is said to have a coordination number of 8.

If we isolate a single hard-sphere unit cell, we obtain the model shown inFig. 3.4c. Each of these cells has the equivalent of two atoms per unit cell. Onecomplete atom is located at the center of the unit cell, and an eighth of a sphereis located at each corner of the cell, making the equivalent of another atom. Thusthere is a total of 1 (at the center) + 8 18 (at the corners) = 2 atoms per unitcell. The atoms in the BCC unit cell contact each other across the cube diagonal,as indicated in Fig. 3.5, so that the relationship between the length of the cubeside a and the atomic radius R is

3a = 4R or a = 4R

3(3.1)

Table 3.4 Selected Metals That Have the HCP Crystal Structure at Room Temperature(20C) and Their Lattice Constants, Atomic Radii, and c/a Ratios

Lattice constants (nm)Atomic % deviation

Metal a c radius R (nm) c/a ratio from idealityCadmium 0.2973 0.5618 0.149 1.890 +15.7Zinc 0.2665 0.4947 0.133 1.856 +13.6Ideal HCP 1.633 0Magnesium 0.3209 0.5209 0.160 1.623 0.66Cobalt 0.2507 0.4069 0.125 1.623 0.66Zirconium 0.3231 0.5148 0.160 1.593 2.45Titanium 0.2950 0.4683 0.147 1.587 2.81Beryllium 0.2286 0.3584 0.113 1.568 3.98

smi02334_ch03.qxd 4/21/03 3:38 PM Page 73


EXAMPLE PROBLEM 3.2

Iron at 20C is BCC with atoms of atomic radius 0.124 nm. Calculate the latticeconstant a for the cube edge of the iron unit cell.

SolutionFrom Fig. 3.5 it is seen that the atoms in the BCC unit cell touch across the cubediagonals. Thus, if a is the length of the cube edge, then

3a = 4R (3.1)

where R is the radius of the iron atom. Therefore

a = 4R3

= 4(0.124 nm)3

= 0.2864 nm

If the atoms in the BCC unit cell are considered to be spherical, an atomicpacking factor (APF) can be calculated by using the equation

Atomic packing factor (APF) = volume of atoms in unit cellvolume of unit cell

(3.2)

Using this equation, the APF for the BCC unit cell (Fig. 3.3a) is calculated to be68 percent (see Example Problem 3.2). That is, 68 percent of the volume of theBCC unit cell is occupied by atoms and the remaining 32 percent is empty space.The BCC crystal structure is not a close-packed structure since the atoms couldbe packed closer together. Many metals such as iron, chromium, tungsten,molybdenum, and vanadium have the BCC crystal structure at room tempera-ture. Table 3.2 lists the lattice constants and atomic radii of selected BCC metals.

Calculate the atomic packing factor (APF) for the BCC unit cell, assuming the atomsto be hard spheres.

Solution

APF = volume of atoms in BCC unit cellvolume of BCC unit cell

(3.2)

Since there are two atoms per BCC unit cell, the volume of atoms in the unit cell ofradius R is

Vatoms = (2)( 4

3 R3) = 8.373 R3

The volume of the BCC unit cell is

Vunit cell = a3

where a is the lattice constant. The relationship between a and R is obtained fromFig. 3.5, which shows that the atoms in the BCC unit cell touch each other across thecubic diagonal. Thus

3a = 4R or a = 4R

3(3.1)

EXAMPLE PROBLEM 3.1

smi02334_ch03.qxd 4/21/03 3:38 PM Page 74


a

4R

2 a 4R

2 a

Figure 3.7FCC unit cell showingrelationship between thelattice constant a and atomicradius R. Since the atomstouch across the facediagonals, .2a = 4R

(a) (b) (c)

Figure 3.6FCC unit cells: (a) atomic-site unit cell, (b) hard-sphere unit cell, and (c) isolated unit cell.

ThusVunit cell = a3 = 12.32 R3

The atomic packing factor for the BCC unit cell is, therefore,

APF = Vatoms /unit cellVunit cell

= 8.373 R3

12.32 R3= 0.68

3.3.2 Face-Centered Cubic (FCC) Crystal Structure

Consider next the FCC lattice-point unit cell of Fig. 3.6a. In this unit cell there isone lattice point at each corner of the cube and one at the center of each cubeface. The hard-sphere model of Fig. 3.6b indicates that the atoms in the FCCcrystal structure are packed as close together as possible. The APF for this close-packed structure is 0.74 as compared to 0.68 for the BCC structure, which is notclose-packed.

The FCC unit cell as shown in Fig. 3.6c has the equivalent of four atoms perunit cell. The eight corner octants account for one atom (8 18 = 1), and the sixhalf-atoms on the cube faces contribute another three atoms, making a total offour atoms per unit cell. The atoms in the FCC unit cell contact each other acrossthe cubic face diagonal, as indicated in Fig. 3.7, so that the relationship betweenthe length of the cube side a and the atomic radius R is

2a = 4R or a = 4R

2(3.3)

The APF for the FCC crystal structure is 0.74, which is greater than the0.68 factor for the BCC structure. The APF of 0.74 is for the closest packingpossible of spherical atoms. Many metals such as aluminum, copper, lead,

smi02334_ch03.qxd 4/21/03 3:38 PM Page 75


nickel, and iron at elevated temperatures (912 to 1394C) crystallize with theFCC crystal structure. Table 3.3 lists the lattice constants and atomic radii forsome selected FCC metals.

3.3.3 Hexagonal Close-Packed (HCP) Crystal Structure

The third common metallic crystal structure is the HCP structure shown inFig. 3.8. Metals do not crystallize into the simple hexagonal crystal structureshown in Fig. 3.2 because the APF is too low. The atoms can attain a lowerenergy and a more stable condition by forming the HCP structure of Fig. 3.8. TheAPF of the HCP crystal structure is 0.74, the same as that for the FCC crystalstructure since in both structures the atoms are packed as tightly as possible.In both the HCP and FCC crystal structures each atom is surrounded by 12other atoms, and thus both structures have a coordination number of 12. Thedifferences in the atomic packing in FCC and HCP crystal structures will be dis-cussed in Sec. 3.8.

The isolated HCP unit cell is shown in Fig. 3.8c and has the equivalent of sixatoms per unit cell. Three atoms form a triangle in the middle layer, as indicatedby the atomic sites in Fig. 3.8a. There are six 16 -atom sections on both the topand bottom layers, making an equivalent of two more atoms (2 6 16 = 2).Finally, there is one-half of an atom in the center of both the top and bottom lay-ers, making the equivalent of one more atom. The total number of atoms in theHCP crystal structure unit cell is thus 3 + 2 + 1 = 6.

The ratio of the height c of the hexagonal prism of the HCP crystal structureto its basal side a is called the c/a ratio (Fig. 3.8a). The c/a ratio for an ideal HCPcrystal structure consisting of uniform spheres packed as tightly together aspossible is 1.633. Table 3.4 lists some important HCP metals and their c/a ratios.Of the metals listed, cadmium and zinc have c/a ratios higher than ideality, which

(a) (c)(b)

Figure 3.8HCP unit cells: (a) atomic-site unit cell, (b) hard-sphere unit cell, and (c) isolated unit cell.[(b) and (c) After F. M. Miller, Chemistry: Structure and Dynamics, McGraw-Hill, 1984, p. 296.]

smi02334_ch03.qxd 4/21/03 3:38 PM Page 76


EXAMPLEPROBLEM 3.3

indicates that the atoms in these structures are slightly elongated along the c axisof the HCP unit cell. The metals magnesium, cobalt, zirconium, titanium, andberyllium have c/a ratios less than the ideal ratio. Therefore, in these metals theatoms are slightly compressed in the direction along the c axis. Thus, for the HCPmetals listed in Table 3.4 there is a certain amount of deviation from the idealhard-sphere model.

Calculate the volume of the zinc crystal structure unit cell by using the following data:pure zinc has the HCP crystal structure with lattice constants a = 0.2665 nm andc = 0.4947 nm. SolutionThe volume of the zinc HCP unit cell can be obtained by determining the area of thebase of the unit cell and then multiplying this by its height (Fig. 3.9).

The area of the base of the unit cell is area ABDEFG of Fig. 3.9a and b. This totalarea consists of the areas of six equilateral triangles of area ABC of Fig. 3.9b. FromFig. 3.9c,

Area of triangle A BC = 12 (base)(height )= 12 (a)(a sin 60) = 12 a2 sin 60

From Fig. 3.9b,Total area of HCP base = (6) ( 12 a2 sin 60)

= 3a2 sin 60

From Fig. 3.9a,

Volume of zinc HCP unit cell = (3a2 sin 60)(c)= (3)(0.2665 nm)2(0.8660)(0.4947 nm)= 0.0913 nm3

A B

CCD

EF

G

a

CD

EF

G

A Ba

c

(a) (b) (c)

A B6060

a

ha

CC

Figure 3.9Diagrams for calculating the volume of an HCP unit cell. (a) HCP unit cell.(b) Base of HCP unit cell. (c) Triangle ABC removed from base of unit cell.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 77


z

x

a

(0, 0, 1) (0, 1, 1)

1, 0)

(1, 0, 1)

(0

(0, 0, 0)

(0

(0, 1,

(0, 0, 1)

1, 0, 0)

y

x

x

Figure 3.10(a) Rectangular x, y, and z axes for locating atom positions in cubicunit cells. (b) Atom positions in a BCC unit cell.

3.4 ATOM POSITIONS IN CUBIC UNIT CELLSTo locate atom positions in cubic unit cells, we use rectangular x, y, and z axes.In crystallography the positive x axis is usually the direction coming out of thepaper, the positive y axis is the direction to the right of the paper, and the positivez axis is the direction to the top (Fig. 3.10). Negative directions are opposite tothose just described.

Atom positions in unit cells are located by using unit distances along the x,y, and z axes, as indicated in Fig. 3.10a. For example, the position coordinates forthe atoms in the BCC unit cell are shown in Fig. 3.10b. The atom positions forthe eight corner atoms of the BCC unit cell are

(0, 0, 0) (1, 0, 0) (0, 1, 0) (0, 0, 1)(1, 1, 1) (1, 1, 0) (1, 0, 1) (0, 1, 1)

The center atom in the BCC unit cell has the position coordinates ( 12 , 12 , 12 ). Forsimplicity sometimes only two atom positions in the BCC unit cell are specifiedwhich are (0, 0, 0) and ( 12 , 12 , 12 ). The remaining atom positions of the BCC unitcell are assumed to be understood. In the same way the atom positions in theFCC unit cell can be located.

3.5 DIRECTIONS IN CUBIC UNIT CELLSOften it is necessary to refer to specific directions in crystal lattices. This isespecially important for metals and alloys with properties that vary with crystal-lographic orientation. For cubic crystals the crystallographic direction indicesare the vector components of the direction resolved along each of the coordinateaxes and reduced to the smallest integers.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 78

3.5 Directions in Cubic Unit Cells 79

z

y

x

z

y

x

z

y

x

z

y

x

O

R S

Origin[100]

[110]OO

T

[111] O

N[110]

Note neworigin

OM

[210]

(a) (b) (c) (d)

12

Figure 3.11Some directions in cubic unit cells.

To diagrammatically indicate a direction in a cubic unit cell, we draw a di-rection vector from an origin, which is usually a corner of the cubic cell, until itemerges from the cube surface (Fig. 3.11). The position coordinates of the unitcell where the direction vector emerges from the cube surface after being con-verted to integers are the direction indices. The direction indices are enclosed bysquare brackets with no separating commas.

For example, the position coordinates of the direction vector OR inFig. 3.11a where it emerges from the cube surface are (1, 0, 0), and so the direc-tion indices for the direction vector OR are [100]. The position coordinates of thedirection vector OS (Fig. 3.11a) are (1, 1, 0), and so the direction indices for OSare [110]. The position coordinates for the direction vector OT (Fig. 3.11b) are(1, 1, 1), and so the direction indices of OT are [111].

The position coordinates of the direction vector OM (Fig. 3.11c) are (1, 12 , 0),and since the direction vectors must be integers, these position coordinates mustbe multiplied by 2 to obtain integers. Thus, the direction indices of OM become2(1, 12 , 0) = [210] . The position coordinates of the vector ON (Fig. 3.11d) are(1, 1, 0). A negative direction index is written with a bar over the index. Thus,the direction indices for the vector ON are [110]. Note that to draw the directionON inside the cube the origin of the direction vector had to be moved to the frontlower-right corner of the unit cube (Fig. 3.11d). Further examples of cubic di-rection vectors are given in Example Problem 3.4.

The letters u, v, w are used in a general sense for the direction indices in thex, y, and z directions, respectively, and are written as [uvw]. It is also importantto note that all parallel direction vectors have the same direction indices.

Directions are said to be crystallographically equivalent if the atom spacingalong each direction is the same. For example, the following cubic edge direc-tions are crystallographic equivalent directions:

[100], [010], [001], [010], [001], [100] 100Equivalent directions are called indices of a family or form. The notation 100is used to indicate cubic edge directions collectively. Other directions of a formare the cubic body diagonals 111 and the cubic face diagonals 110.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 79


EXAMPLE PROBLEM 3.4

Draw the following direction vectors in cubic unit cells:

(a) [100] and [110](b) [112](c) [110](d) [321] Solution(a) The position coordinates for the [100] direction are (1, 0, 0) (Fig. 3.12a). The

position coordinates for the [110] direction are (1, 1, 0) (Fig. 3.12a).(b) The position coordinates for the [112] direction are obtained by dividing the

direction indices by 2 so that they will lie within the unit cube. Thus they are( 12 , 12 , 1) (Fig. 3.12b).

(c) The position coordinates for the [110] direction are (1, 1, 0) (Fig. 3.12c).Note that the origin for the direction vector must be moved to the lower-leftfront corner of the cube.

(d) The position coordinates for the [321] direction are obtained by first dividingall the indices by 3, the largest index. This gives 1, 23 , 13 for the positioncoordinates of the exit point of the direction [321], which are shown in Fig. 3.12d.

x

z

y

x

z

y

x

z

z

y

x

OOrigin

[100] [110]

ONote new origin

Note new origin

[110][321]

[112]

O

O

13

O

(a) (b)

(c) (d)

y

12

12

12

12

23

Figure 3.12Direction vectors in cubic unit cells.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 80

3.5 Directions in Cubic Unit Cells 81

EXAMPLEPROBLEM 3.5

Determine the direction indices of the cubic direction shown in Fig. EP3.5a. SolutionParallel directions have the same direction indices, and so we move the direction vec-tor in a parallel manner until its tail reaches the nearest corner of the cube, still keep-ing the vector within the cube. Thus, in this case, the upper-left front corner becomesthe new origin for the direction vector (Fig. EP3.5b). We can now determine the posi-tion coordinates where the direction vector leaves the unit cube. These are x = 1,y = +1, and z = 16 . The position coordinates of the direction where it leaves theunit cube are thus (1, +1, 16 ). The direction indices for this direction are, afterclearing the fraction 6x , (1, +1, 16 ), or [661].

EXAMPLEPROBLEM 3.6

Determine the direction indices of the cubic direction between the position coordi-nates ( 34 , 0, 14 ) and ( 14 , 12 , 12 ). SolutionFirst we locate the origin and termination points of the direction vector in a unit cube,as shown in Fig. EP3.6. The fraction vector components for this direction are

x = ( 34 14 ) = 12y = ( 12 0) = 12z = ( 12 14 ) = 14

Thus, the vector direction has fractional vector components of 12 , 12 , 14 . The direction in-dices will be in the same ratio as their fractional components. By multiplying the fractionvector components by 4, we obtain [221] for the direction indices of this vector direction.

34

14

Origin for positioncoordinates

z

yx

Figure EP3.6

Figure EP3.5

13

12

1

12

(0, 0, 0)

Neworigin

131

2

zz

yyxx

(a) (b)

smi02334_ch03.qxd 4/21/03 3:38 PM Page 81


5William Hallowes Miller (18011880). English crystallographer who published a Treatise onCrystallography in 1839, using crystallographic reference axes that were parallel to the crystal edgesand using reciprocal indices.

3.6 MILLER INDICES FORCRYSTALLOGRAPHIC PLANESIN CUBIC UNIT CELLS

Sometimes it is necessary to refer to specific lattice planes of atoms within acrystal structure, or it may be of interest to know the crystallographic orientationof a plane or group of planes in a crystal lattice. To identify crystal planes incubic crystal structures, the Miller notation system5 is used. The Miller indices ofa crystal plane are defined as the reciprocals of the fractional intercepts (withfractions cleared) that the plane makes with the crystallographic x, y, and z axesof the three nonparallel edges of the cubic unit cell. The cube edges of the unitcell represent unit lengths, and the intercepts of the lattice planes are measured interms of these unit lengths.

The procedure for determining the Miller indices for a cubic crystal plane isas follows:

1. Choose a plane that does not pass through the origin at (0, 0, 0).2. Determine the intercepts of the plane in terms of the crystallographic x, y,

and z axes for a unit cube. These intercepts may be fractions.3. Form the reciprocals of these intercepts.4. Clear fractions and determine the smallest set of whole numbers that are in

the same ratio as the intercepts. These whole numbers are the Millerindices of the crystallographic plane and are enclosed in parentheseswithout the use of commas. The notation (hkl) is used to indicate Millerindices in a general sense, where h, k, and l are the Miller indices of a cubiccrystal plane for the x, y, and z axes, respectively.Figure 3.13 shows three of the most important crystallographic planes of

cubic crystal structures. Let us first consider the shaded crystal plane in Fig. 3.13a,which has the intercepts 1, , for the x, y, and z axes, respectively. We takethe reciprocals of these intercepts to obtain the Miller indices, which are therefore1, 0, 0. Since these numbers do not involve fractions, the Miller indices for thisplane are (100), which is read as the one-zero-zero plane. Next let us consider thesecond plane shown in Fig. 3.13b. The intercepts of this plane are 1, 1, . Sincethe reciprocals of these numbers are 1, 1, 0, which do not involve fractions, theMiller indices of this plane are (110). Finally, the third plane (Fig. 3.13c) hasthe intercepts 1, 1, 1, which give the Miller indices (111) for this plane.

Consider now the cubic crystal plane shown in Fig. 3.14 which has the in-tercepts 13 ,

23 , 1. The reciprocals of these intercepts are 3,

32 , 1. Since fractional in-

tercepts are not allowed, these fractional intercepts must be multiplied by 2 toclear the 32 fraction. Thus, the reciprocal intercepts become 6, 3, 2 and the Miller

smi02334_ch03.qxd 4/21/03 3:38 PM Page 82

3.6 Miller Indices for Crystallographic Planes in Cubic Unit Cells 83

(632)

Oy

z

x

13

23

Figure 3.14Cubic crystal plane (632), whichhas fractional intercepts.

x

z

x

z

x

z

(100)

(a)

(110)

(b)

(111)

(c)

yyy

Figure 3.13Miller indices of some important cubic crystal planes: (a) (100), (b) (110), and (c) (111).

indices are (632). Further examples of cubic crystal planes are shown in Exam-ple Problem 3.7.

If the crystal plane being considered passes through the origin so that one ormore intercepts are zero, the plane must be moved to an equivalent position inthe same unit cell and the plane must remain parallel to the original plane. Thisis possible because all equispaced parallel planes are indicated by the sameMiller indices.

If sets of equivalent lattice planes are related by the symmetry of the crystalsystem, they are called planes of a family or form, and the indices of one plane ofthe family are enclosed in braces as {hkl} to represent the indices of a family ofsymmetrical planes. For example, the Miller indices of the cubic surface planes(100), (010), and (001) are designated collectively as a family or form by thenotation {100}.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 83


EXAMPLE PROBLEM 3.7

x

z

yy

z

x

y

z

x

z

x

(101)

O

(a)

O

(221)

12

12

(c)

O

(110)Note new

origin

(b)

(d )

yO

(110)

Draw the following crystallographic planes in cubic unit cells:

(a) (101) (b) (110) (c) (221)(d) Draw a (110) plane in a BCC atomic-site unit cell, and list the position

coordinates of the atoms whose centers are intersected by this plane.

Solutions

(a) First determine the reciprocals of the Miller indices of the (101) plane. Theseare 1, , 1. The (101) plane must pass through a unit cube at intercepts x = 1and z = 1 and be parallel to the y axis.

(b) First determine the reciprocals of the Miller indices of the (110) plane. Theseare 1, 1, . The (110) plane must pass through a unit cube at intercepts x = 1and y = 1 and be parallel to the z axis. Note that the origin of axes must bemoved to the lower-right back side of the cube.

(c) First determine the reciprocals of the Miller indices of the (221) plane. Theseare 12 ,

12 , 1. The (221) plane must pass through a unit cube at intercepts x = 12 ,

y = 12 , and z = 1.(d ) Atom positions whose centers are intersected by the (110) plane are (1, 0, 0), (0,

1, 0), (1, 0, 1), (0, 1, 1), and ( 12 , 12 , 12 ). These positions are indicated by the solidcircles.

Figure EP3.7Various important cubic crystal planes.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 84

3.6 Miller Indices for Crystallographic Planes in Cubic Unit Cells 85

d110

d110

a

A

B

O

C

a

x

y

(110) plane 1

(110) plane 2

(110) plane 3

Figure 3.15Top view of cubic unit cell showing the distancebetween (110) crystal planes, d110.

EXAMPLEPROBLEM 3.8

An important relationship for the cubic system, and only the cubic system, isthat the direction indices of a direction perpendicular to a crystal plane are thesame as the Miller indices of that plane. For example, the [100] direction is per-pendicular to the (100) crystal plane.

In cubic crystal structures the interplanar spacing between two closest par-allel planes with the same Miller indices is designated dhkl , where h, k, and l arethe Miller indices of the planes. This spacing represents the distance from a se-lected origin containing one plane and another parallel plane with the same in-dices that is closest to it. For example, the distance between (110) planes 1 and 2,d110, in Fig. 3.15 is AB. Also, the distance between (110) planes 2 and 3 is d110and is length BC in Fig. 3.15. From simple geometry, it can be shown that forcubic crystal structures

dhkl =a

h2 + k2 + l2 (3.4)

where dhkl = interplanar spacing between parallel closest planes withMiller indices h, k, and l

a = lattice constant (edge of unit cube)h, k, l = Miller indices of cubic planes being considered

Determine the Miller indices of the cubic crystallographic plane shown in Fig. EP3.8a.

SolutionFirst, transpose the plane parallel to the z axis 14 unit to the right along the y axis asshown in Fig. EP3.8b so that the plane intersects the x axis at a unit distance from the

smi02334_ch03.qxd 4/21/03 3:38 PM Page 85


EXAMPLE PROBLEM 3.9

z

yD

AB

C E (origin for plane)

Origin forpositioncoordinates

x

121, 1,

12 2 , 1, 0

1, , 014

14 , 1,

34

new origin located at the lower-right back corner of the cube. The new interceptsof the transposed plane with the coordinate axes are now (+1, 512 , ). Next, wetake the reciprocals of these intercepts to give (1, 125 , 0). Finally, we clear the 125 frac-tion to obtain (5120) for the Miller indices of this plane.

Determine the Miller indices of the cubic crystal plane that intersects the position co-ordinates (1, 14 , 0), (1, 1, 12 ), ( 34 , 1, 14 ), and all coordinate axes.

SolutionFirst, we locate the three position coordinates as indicated in Fig. EP3.9 at A, B, andC. Next, we join A and B and extend AB to D and then join A and C. Finally, we joinA to C to complete plane ACD. The origin for this plane in the cube can be chosen atE, which gives axial intercepts for plane ACD at x = 12 , y = 34 , and z = 12 . Thereciprocals of these axial intercepts are 2, 43 , and 2. Multiplying these intercepts by3 clears the fraction, giving Miller indices for the plane of (646).

Neworigin

13

2314

512 z

y

z

y

xx34

(a) (b)

Figure EP3.8

Figure EP3.9

smi02334_ch03.qxd 4/21/03 3:38 PM Page 86

3.7 Crystallographic Planes and Directions in Hexagonal Unit Cells 87

EXAMPLEPROBLEM 3.10

Copper has an FCC crystal structure and a unit cell with a lattice constant of 0.361 nm.What is its interplanar spacing d220?

Solution

dhkl =a

h2 + k2 + l2= 0.361 nm

(2)2 + (2)2 + (0)2= 0.128 nm

3.7 CRYSTALLOGRAPHIC PLANES ANDDIRECTIONS IN HEXAGONAL UNIT CELLS

3.7.1 Indices for Crystal Planes in HCP Unit Cells

Crystal planes in HCP unit cells are commonly identified by using four indicesinstead of three. The HCP crystal plane indices, called Miller-Bravais indices,are denoted by the letters h, k, i, and l and are enclosed in parentheses as (hkil).These four-digit hexagonal indices are based on a coordinate system with fouraxes, as shown in Fig. 3.16 in an HCP unit cell. There are three basal axes, a1,a2, and a3, which make 120 with each other. The fourth axis or c axis is thevertical axis located at the center of the unit cell. The a unit of measurementalong the a1, a2, and a3 axes is the distance between the atoms along these axesand is indicated in Fig. 3.16. The unit of measurement along the c axis is theheight of the unit cell. The reciprocals of the intercepts that a crystal plane makeswith the a1, a2, and a3 axes give the h, k, and i indices, while the reciprocal of theintercept with the c axis gives the l index.

c

a

a2

a3

a1

a2

a3

a1

c

Figure 3.16The four coordinate axes (a1, a2, a3,and c) of the HCP crystal structureunit cell.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 87


(b)

c

E

B C

F

AD

H

Ga3

a2 a2

a1a3

a1

Interceptis 1

Interceptis 1

Interceptis 1

Interceptis 1

(0110)

(1100)(1010)

(a)

c

a3

a2 a2

a1a3

a1

(0001)

Basal Planes The basal planes of the HCP unit cell are very important planesfor this unit cell and are indicated in Fig. 3.17a. Since the basal plane on the topof the HCP unit cell in Fig. 3.17a is parallel to the a1, a2, and a3 axes, theintercepts of this plane with these axes will all be infinite. Thus, a1 = ,a2 = , and a3 = . The c axis, however, is unity since the top basal planeintersects the c axis at unit distance. Taking the reciprocals of these interceptsgives the Miller-Bravais indices for the HCP basal plane. Thus h = 0, k = 0,i = 0, and l = 1. The HCP basal plane is, therefore, a zero-zero-zero-one or(0001) plane.Prism Planes Using the same method, the intercepts of the front prism plane(ABCD) of Fig. 3.17b are a1 = +1, a2 = , a3 = 1, and c = . Takingthe reciprocals of these intercepts gives h = 1, k = 0, i = 1, and l = 0, or the(1010) plane. Similarly, the ABEF prism plane of Fig. 3.17b has the indices(1100) and the DCGH plane the indices (0110). All HCP prism planes can beidentified collectively as the {1010} family of planes.

Sometimes HCP planes are identified only by three indices (hkl) sinceh + k = i . However, the (hkil) indices are used more commonly because theyreveal the hexagonal symmetry of the HCP unit cell.

3.7.2 Direction Indices in HCP Unit Cells6

Directions in HCP unit cells are also usually indicated by four indices u, v, t,and w enclosed by square brackets as [uvtw]. The u, v, and t indices are lattice

6The topic of direction indices for hexagonal unit cells is not normally presented in an introductorycourse in materials but is included here for advanced students.

Figure 3.17Miller-Bravais indices of hexagonal crystal planes: (a) basal planes, and (b) prismplanes.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 88

3.7 Crystallographic Planes and Directions in Hexagonal Unit Cells 89

vectors in the a1 , a2 , and a3 directions, respectively (Fig. 3.16), and the windex is a lattice vector in the c direction. To maintain uniformity for bothHCP indices for planes and directions, it has been agreed that u v t fordirections.

Let us now determine the Miller-Bravais hexagonal indices for the direc-tions a1, a2, and a3, which are the positive basal axes of the hexagonal unit cell.The a1 direction indices are given in Fig. 3.18a, the a2 direction indices inFig. 3.18b and the a3 direction indices in Fig. 3.18c. If we need to indicate a cdirection also for the a3 direction, this is shown in Fig. 3.18d. Fig. 3.18e summa-rizes the positive and negative directions on the upper basal plane of the simplehexagonal crystal structure.

a1

a3

a2 a1

a3

a2 [1210]

(b)

a1

a3

a2 a1

a3

a2

[2110]

(a)

a1

a

a2 a1

a3

a2

[1120]

(c)

[1121]

[11

[1 10]

(d)

a

c

a3

a2 a1

a2

aa1

[211

[1120]

(e)

a2

a1

a3

a2

a3

a1

[1 0]0

Figure 3.18Miller-Bravais hexagonal crystal structure direction indices for principal directions: (a) +a1 axis directionon basal plane, (b) +a2 axis direction on basal plane, (c) +a3 direction axis on basal plane, and (d ) +a3direction axis incorporating c axis. (e) Positive and negative Miller-Bravais directions are indicated insimple hexagonal crystal structure on upper basal plane.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 89

3.8 COMPARISON OF FCC, HCP, AND BCCCRYSTAL STRUCTURES

3.8.1 Face-Centered Cubic and Hexagonal Close-PackedCrystal Structures

As previously pointed out, both the HCP and FCC crystal structures are close-packed structures. That is, their atoms, which are considered approximatespheres, are packed together as closely as possible so that an atomic packingfactor of 0.74 is attained.7 The (111) planes of the FCC crystal structure shown inFig. 3.19a have the identical packing arrangement as the (0001) planes of theHCP crystal structure shown in Fig. 3.19b. However, the three-dimensional FCCand HCP crystal structures are not identical because there is a difference in thestacking arrangement of their atomic planes, which can best be described by con-sidering the stacking of hard spheres representing atoms. As a useful analogy,one can imagine the stacking of planes of equal-sized marbles on top of eachother, minimizing the space between the marbles.

Consider first a plane of close-packed atoms designated the A plane, asshown in Fig. 3.20a. Note that there are two different types of empty spaces or


(111)plane

(0001) plane

(a) (b)

Figure 3.19Comparison of the (a) FCC crystal structure showing theclose-packed (111) planes, and (b) the HCP crystal structureshowing the close-packed (0001) planes.(After W. G. Moffatt, G. W. Pearsall, and J. Wulff, The Structure andProperties of Materials, vol. I: Structure, Wiley, 1964, p. 51.)

7As pointed out in Sec. 3.3, the atoms in the HCP structure deviate to varying degrees from ideality. Insome HCP metals the atoms are elongated along the c axis, and in other cases they are compressed alongthe c axis (see Table 3.4).

smi02334_ch03.qxd 4/21/03 3:38 PM Page 90

voids between the atoms. The voids pointing to the top of the page are designateda voids and those pointing to the bottom of the page, b voids. A second planeof atoms can be placed over the a or b voids and the same three-dimensionalstructure will be produced. Let us place plane B over the a voids, as shown inFig. 3.20b. Now if a third plane of atoms is placed over plane B to form a closest-packed structure, it is possible to form two different close-packed structures. Onepossibility is to place the atoms of the third plane in the b voids of the B plane.Then the atoms of this third plane will lie directly over those of the A plane andthus can be designated another A plane (Fig. 3.20c). If subsequent planes ofatoms are placed in this same alternating stacking arrangement, then the stackingsequence of the three-dimensional structure produced can be denoted byABABAB. . . . Such a stacking sequence leads to the HCP crystal structure(Fig. 3.19b).

The second possibility for forming a simple close-packed structure is toplace the third plane in the a voids of plane B (Fig. 3.20d ). This third plane isdesignated the C plane since its atoms do not lie directly above those of the Bplane or the A plane. The stacking sequence in this close-packed structure is thusdesignated ABCABCABC . . . and leads to the FCC structure shown in Fig. 3.19a.

3.8 Comparison of FCC, HCP, and BCC Crystal Structures 91

A plane

A plane

B planeA planeB planeC plane

(a) (b)

(c) (d)

A planeB planea voidb void

A planea voidb void

Figure 3.20Formation of the HCP and FCC crystal structures by the stackingof atomic planes. (a) A plane showing the a and b voids. (b) B planeplaced in a voids of plane A. (c) Third plane placed in b voids of Bplane, making another A plane and forming the HCP crystalstructure. (d) Third plane placed in the a voids of B plane, makinga new C plane and forming the FCC crystal structure.(Adapted from P. Ander and A. J. Sonnessa, Principles of Chemistry, Macmillan, 1965, p. 661.)

smi02334_ch03.qxd 4/21/03 3:38 PM Page 91


a

2a

[111] [111]

(100)plane

(110)plane

(a) (b)

Figure 3.21BCC crystal structure showing (a) the (100) plane and (b) a section of the (110) plane.Note that this is not a close-packed structure but that diagonals are close-packeddirections.[(a) After W. G. Moffatt, G. W. Pearsall, and J. Wulff, The Structure and Properties of Materials, vol. I:Structure, Wiley, 1964, p. 51.]

3.8.2 Body-Centered Cubic Crystal Structure

The BCC structure is not a close-packed structure and hence does not have close-packed planes like the {111} planes in the FCC structure and the {0001} planes inthe HCP structure. The most densely packed planes in the BCC structure are the{110} family of planes of which the (110) plane is shown in Fig. 3.21b. However,the atoms in the BCC structure do have close-packed directions along the cubediagonals, which are the 111 directions.

3.9 VOLUME, PLANAR, AND LINEAR DENSITYUNIT-CELL CALCULATIONS

3.9.1 Volume Density

Using the hard-sphere atomic model for the crystal structure unit cell of a metaland a value for the atomic radius of the metal obtained from x-ray diffractionanalysis, a value for the volume density of a metal can be obtained by using theequation

Volume density of metal = =mass/unit cell

volume/unit cell(3.5)

In Example Problem 3.11 a value of 8.98 Mg/m3 (8.98 g/cm3) is obtained for thedensity of copper. The handbook experimental value for the density of copper is8.96 Mg/m3 (8.96 g/cm3). The slightly lower density of the experimental valuecould be attributed to the absence of atoms at some atomic sites (vacancies),

smi02334_ch03.qxd 4/21/03 3:38 PM Page 92

3.9 Volume, Planar, and Linear Density Unit-Cell Calculations 93

EXAMPLEPROBLEM 3.11

line defects, and mismatch where grains meet (grain boundaries). These crys-talline defects are discussed in Chap. 4. Another cause of the discrepancy couldalso be due to the atoms not being perfect spheres.

Copper has an FCC crystal structure and an atomic radius of 0.1278 nm. Assuming theatoms to be hard spheres that touch each other along the face diagonals of the FCCunit cell as shown in Fig. 3.7, calculate a theoretical value for the density of copper inmegagrams per cubic meter. The atomic mass of copper is 63.54 g/mol.

SolutionFor the FCC unit cell,

2a = 4R , where a is the lattice constant of the unit cell and R

is the atomic radius of the copper atom. Thus

a = 4R2

= (4)(0.1278 nm)2

= 0.361 nm

Volume density of copper = =mass/unit cell

volume/unit cell(3.5)

In the FCC unit cell there are four atoms/unit cell. Each copper atom has a mass of(63.54 g/mol)/(6.02 1023 atoms/mol). Thus the mass m of Cu atoms in the FCC unitcell is

m = (4 atoms )(63.54 g/mol)6.02 1023 atoms/ mol

(106 Mg

g

)= 4.22 1028 Mg

The volume V of the Cu unit cell is

V = a3 =(

0.361 nm 109 m

nm

)3= 4.70 1029 m3

Thus the density of copper is

=m

V= 4.22 10

28 Mg4.70 1029 m3 = 8.98 Mg/m

3 (8.98 g/cm3)

3.9.2 Planar Atomic Density

Sometimes it is important to determine the atomic densities on various crystalplanes. To do this a quantity called the planar atomic density is calculated byusing the relationship

Planar atomic density = p =equiv. no. of atoms whose centers

are intersected by selected areaselected area (3.6)

For convenience the area of a plane that intersects a unit cell is usually used inthese calculations, as shown, for example, in Fig. 3.22 for the (110) plane in aBCC unit cell. In order for an atom area to be counted in this calculation, theplane of interest must intersect the center of an atom. In Example Problem 3.12

smi02334_ch03.qxd 4/21/03 3:38 PM Page 93


z

x

y

aa (110)

(a) (b)

2a

2a

Figure 3.22(a) A BCC atomic-site unit cell showing a shaded (110) plane. (b) Areas of atoms in BCC unit cell cut by the (110) plane.

EXAMPLEPROBLEM 3.12

the (110) plane intersects the centers of five atoms, but the equivalent of only twoatoms is counted since only one-quarter of each of the four corner atoms isincluded in the area inside the unit cell.

Calculate the planar atomic density p on the (110) plane of the iron BCC lattice inatoms per square millimeter. The lattice constant of iron is 0.287 nm.

Solution

p =equiv. no. of atoms whose centers are intersected by selected area

selected area(3.6)

The equivalent number of atoms intersected by the (110) plane in terms of the surfacearea inside the BCC unit cell is shown in Fig. 3.22 and is

1 atom at center + 4 14 atoms at four corners of plane = 2 atomsThe area intersected by the (110) plane inside the unit cell (selected area) is

(

2a)(a) =

2a2

Thus the planar atomic density is

p =2 atoms

2(0.287 nm)2= 17.2 atoms

nm2

= 17.2 atomsnm2

1012 nm2

mm2

= 1.72 1013 atoms/mm2

smi02334_ch03.qxd 4/21/03 3:38 PM Page 94

3.9 Volume, Planar, and Linear Density Unit-Cell Calculations 95

EXAMPLEPROBLEM 3.13

3.9.3 Linear Atomic Density

Sometimes it is important to determine the atomic densities in various directionsin crystal structures. To do this a quantity called the linear atomic density is cal-culated by using the relationship

Linear atomic density = l =no. of atomic diam. intersected by selected

length of line in direction of interestselected length of line

(3.7)Example Problem 3.13 shows how the linear atomic density can be calculated inthe [110] direction in a pure copper crystal lattice.

Calculate the linear atomic density l in the [110] direction in the copper crystal lat-tice in atoms per millimeter. Copper is FCC and has a lattice constant of 0.361 nm.

SolutionThe atoms whose centers the [110] direction intersects are shown in Fig. 3.23. Weshall select the length of the line to be the length of the face diagonal of the FCC unitcell, which is

2a . The number of atomic diameters intersected by this length of line

are 12 + 1 + 12 = 2 atoms. Thus using Eq. 3.7, the linear atomic density is

l =2 atoms

2a= 2 atoms

2(0.361 nm)= 3.92 atoms

nm

= 3.92 atomsnm

106 nm

mm

= 3.92 106 atoms/mm

z

x

yO

a

[110]

Figure 3.23Diagram for calculating theatomic linear density in the [110]direction in an FCC unit cell.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 95


15391394

912

273

Liquid ironC

(delta) iron (BCC)

(gamma) iron (FCC)

(alpha) iron (BCC)

Tem

pera

ture

Figure 3.24Allotropic crystalline forms ofiron over temperature rangesat atmospheric pressure

3.10 POLYMORPHISM OR ALLOTROPYMany elements and compounds exist in more than one crystalline form underdifferent conditions of temperature and pressure. This phenomenon is termedpolymorphism, or allotropy. Many industrially important metals such as iron,titanium, and cobalt undergo allotropic transformations at elevated temperaturesat atmospheric pressure. Table 3.5 lists some selected metals that show allotropictransformations and the structure changes that occur.

Iron exists in both BCC and FCC crystal structures over the temperaturerange from room temperature to its melting point at 1539C, as shown inFig. 3.24. Alpha () iron exists from 273 to 912C and has the BCC crystalstructure. Gamma ( ) iron exists from 912 to 1394C and has the FCC crystal

Table 3.5 Allotropic Crystalline Forms of Some Metals

Crystal structure At otherMetal at room temperature temperatures

Ca FCC BCC (> 447C)Co HCP FCC (> 427C)Hf HCP BCC (> 1742C)Fe BCC FCC (9121394C)

BCC (> 1394C)Li BCC HCP (< 193C)Na BCC HCP (< 233C)Tl HCP BCC (> 234C)Ti HCP BCC (> 883C)Y HCP BCC (> 1481C)Zr HCP BCC (> 872C)

smi02334_ch03.qxd 4/21/03 3:38 PM Page 96

3.11 Crystal Structure Analysis 97

EXAMPLEPROBLEM 3.14

structure. Delta () iron exists from 1394 to 1539C, which is the melting pointof iron. The crystal structure of iron is also BCC but with a larger lattice con-stant than iron.

Calculate the theoretical volume change accompanying a polymorphic transformationin a pure metal from the FCC to BCC crystal structure. Assume the hard-sphere atomicmodel and that there is no change in atomic volume before and after the transformation.

SolutionIn the FCC crystal structure unit cell, the atoms are in contact along the face diagonalof the unit cell, as shown in Fig. 3.7. Hence

2a = 4R or a = 4R

2(3.3)

In the BCC crystal structure unit cell, the atoms are in contact along the body di-agonal of the unit cell as shown in Fig. 3.5. Hence

3a = 4R or a = 4R

3(3.1)

The volume per atom for the FCC crystal lattice, since it has four atoms per unitcell, is

VFCC = a3

4=

(4R

2

)3 (14

)= 5.66R3

The volume per atom for the BCC crystal lattice, since it has two atoms per unitcell, is

VBCC = a3

2=

(4R

3

)3 (12

)= 6.16R3

The change in volume associated with the transformation from the FCC to BCC crys-tal structure, assuming no change in atomic radius, is

VVFCC

= VBCC VFCCVFCC

=(

6.16 R3 5.66 R35.66 R3

)100% = +8.8%

3.11 CRYSTAL STRUCTURE ANALYSISOur present knowledge of crystal structures has been obtained mainly by x-raydiffraction techniques that use x-rays about the same wavelength as the distancebetween crystal lattice planes. However, before discussing the manner in which

smi02334_ch03.qxd 4/21/03 3:38 PM Page 97


Cooling water

Target

Beryllium window

Copper

X rays Metal focusing cup

Vacuum

Electrons

TungstenfilamentX rays Glass

To transformer

Figure 3.25Schematic diagram of the cross section of a sealed-off filament x-ray tube.(After B. D. Cullity, Elements of X-Ray Diffraction, 2d ed., Addison-Wesley, 1978, p. 23.)

x-rays are diffracted in crystals, let us consider how x-rays are produced forexperimental purposes.

3.11.1 X-Ray Sources

X-rays used for diffraction are electromagnetic waves with wavelengths in therange 0.05 to 0.25 nm (0.5 to 2.5 ). By comparison, the wavelength of visiblelight is of the order of 600 nm (6000 ). In order to produce x-rays for diffrac-tion purposes, a voltage of about 35 kV is necessary and is applied between acathode and an anode target metal, both of which are contained in a vacuum, asshown in Fig. 3.25. When the tungsten filament of the cathode is heated, elec-trons are released by thermionic emission and accelerated through the vacuumby the large voltage difference between the cathode and anode, thereby gainingkinetic energy. When the electrons strike the target metal (e.g., molybdenum), x-rays are given off. However, most of the kinetic energy (about 98 percent) is con-verted into heat, so the target metal must be cooled externally.

The x-ray spectrum emitted at 35 kV using a molybdenum target is shown inFig. 3.26. The spectrum shows continuous x-ray radiation in the wavelengthrange from about 0.2 to 1.4 (0.02 to 0.14 nm) and two spikes of characteristicradiation that are designated the K and K lines. The wavelengths of the K andK lines are characteristic for an element. For molybdenum, the K line occursat a wavelength of about 0.7 (0.07 nm). The origin of the characteristic radia-tion is explained as follows. First, K electrons (electrons in the n = 1 shell) areknocked out of the atom by highly energetic electrons bombarding the target,leaving excited atoms. Next, some electrons in higher shells (that is, n = 2 or 3)drop down to lower energy levels to replace the lost K electrons, emitting energy

smi02334_ch03.qxd 4/21/03 3:38 PM Page 98


Continuousradiation

Characteristicradiation

Mo K

Mo KK

To 37.2

0.2 0.6Wavelength ()

Rel

ativ

e in

tens

ity

1.0 1.4

16

12

8

4

0

Figure 3.26X-ray emission spectrum produced whenmolybdenum metal is used as the target metalin an x-ray tube operating at 35 kV.

L n 2

K n 1

M n 3

N n 4

Ionization

Ener

gy

K

KK

LL

Figure 3.27Energy levels of electrons inmolybdenum showing the origin of Kand K radiation.

of a characteristic wavelength. The transition of electrons from the L (n = 2)shell to the K (n = 1) shell creates energy of the wavelength of the K line, asindicated in Fig. 3.27.

3.11.2 X-Ray Diffraction

Since the wavelengths of some x-rays are about equal to the distance betweenplanes of atoms in crystalline solids, reinforced diffraction peaks of radiation ofvarying intensities can be produced when a beam of x-rays strikes a crystallinesolid. However, before considering the application of x-ray diffraction tech-niques to crystal structure analysis, let us examine the geometric conditions nec-essary to produce diffracted or reinforced beams of reflected x-rays.

Consider a monochromatic (single-wavelength) beam of x-rays to be inci-dent on a crystal, as shown in Fig. 3.28. For simplification let us allow the crys-tal planes of atomic scattering centers to be replaced by crystal planes that act asmirrors in reflecting the incident x-ray beam. In Fig. 3.28 the horizontal linesrepresent a set of parallel crystal planes with Miller indices (hkl). When an inci-dent beam of monochromatic x-rays of wavelength strikes this set of planes atan angle such that the wave patterns of the beam leaving the various planes arenot in phase, no reinforced beam will be produced (Fig. 3.28a). Thus destructiveinterference occurs. If the reflected wave patterns of the beam leaving the various

smi02334_ch03.qxd 4/21/03 3:38 PM Page 99

planes are in phase, then reinforcement of the beam or constructive interferenceoccurs (Fig. 3.28b).

Let us now consider incident x-rays 1 and 2 as indicated in Fig. 3.28c. Forthese rays to be in phase, the extra distance of travel of ray 2 is equal toMP PN, which must be an integral number of wavelengths . Thus

n = MP + PN (3.8)


Incidentx-rays

No reflectedx-rays

Incidentx-rays

Reflectedx-rays

d

(hkl) planes

(hkl) planes

Incidentx-rays

Ray 1

Ray 2

Reflectedx-rays

(a)

(b)

(c)

d

dM NP

O

2

Figure 3.28The reflection of an x-ray beam by the (hkl ) planesof a crystal. (a) No reflected beam is produced at anarbitrary angle of incidence. (b) At the Bragg angle, the reflected rays are in phase and reinforce oneanother. (c) Similar to (b) except that the waverepresentation has been omitted.(After A. G. Guy and J. J. Hren, Elements of PhysicalMetallurgy, 3d ed., Addison-Wesley, 1974, p. 201.)

smi02334_ch03.qxd 4/21/03 3:38 PM Page 100


8William Henry Bragg (18621942). English physicist who worked in x-ray crystallography.

EXAMPLEPROBLEM 3.15

where n = 1, 2, 3, . . . and is called the order of the diffraction. Since both MPand PN equal dhkl sin , where dhkl is the interplanar spacing of the crystal planesof indices (hkl), the condition for constructive interference (i.e., the productionof a diffraction peak of intense radiation) must be

n = 2dhkl sin (3.9)This equation, known as Braggs law,8 gives the relationship among the angularpositions of the reinforced diffracted beams in terms of the wavelength of theincoming x-ray radiation and of the interplanar spacings dhkl of the crystalplanes. In most cases, the first order of diffraction where n = 1 is used, and so forthis case Braggs law takes the form

= 2dhkl sin (3.10)

A sample of BCC iron was placed in an x-ray diffractometer using incoming x-rayswith a wavelength = 0.1541 nm. Diffraction from the {110} planes was obtained at2 = 44.704 . Calculate a value for the lattice constant a of BCC iron. (Assume first-order diffraction with n = 1.) Solution

2 = 44.704 = 22.35 = 2dhkl sin

d110 =

2 sin = 0.1541 nm

2(sin 22.35)

= 0.1541 nm2(0.3803)

= 0.2026 nm

(3.10)

Rearranging Eq. 3.4 gives

a = dhkl

h2 + k2 + l2

Thusa(Fe) = d110

12 + 12 + 02

= (0.2026 nm)(1.414) = 0.287 nm

3.11.3 X-Ray Diffraction Analysis of Crystal Structures

The Powder Method of X-Ray Diffraction Analysis The most commonlyused x-ray diffraction technique is the powder method. In this technique apowdered specimen is utilized so that there will be a random orientation of manycrystals to ensure that some of the particles will be oriented in the x-ray beam to

smi02334_ch03.qxd 4/21/03 3:38 PM Page 101


Figure 3.29An x-ray diffractometer (with x-radiation shields removed).(Philips Electronic Instruments, Inc.)

9A goniometer is an instrument for measuring angles.

satisfy the diffraction conditions of Braggs law. Modern x-ray crystal analysisuses an x-ray diffractometer that has a radiation counter to detect the angle andintensity of the diffracted beam (Fig. 3.29). A recorder automatically plots theintensity of the diffracted beam as the counter moves on a goniometer9 circle(Fig. 3.30) that is in synchronization with the specimen over a range of 2values. Figure 3.31 shows an x-ray diffraction recorder chart for the intensity ofthe diffracted beam versus the diffraction angles 2 for a powdered pure-metalspecimen. In this way both the angles of the diffracted beams and their intensitiescan be recorded at one time. Sometimes a powder camera with an enclosed

smi02334_ch03.qxd 4/21/03 3:38 PM Page 102


filmstrip is used instead of the diffractometer, but this method is much slowerand in most cases less convenient.Diffraction Conditions for Cubic Unit Cells X-ray diffraction techniquesenable the structures of crystalline solids to be determined. The interpretation ofx-ray diffraction data for most crystalline substances is complex and beyond thescope of this book, and so only the simple case of diffraction in pure cubic metals

Diffracted beam

120110100 90 80 70

50

2

4030

20100

Top view of specimenfixed in goniometer

Radiation detector (movingon goniometer circle)

Radiationgenerator

Incident beam

Radiationgenerator

Portion of one crystalin specimen

Plane 1

Radiationdetector

Plane 2

Parallel( ) planes

in crystal

d

d

2

Figure 3.30Schematic illustration of the diffractometer method of crystal analysis and of the conditionsnecessary for diffraction.(After A. G. Guy, Essentials of Materials Science, McGraw-Hill, 1976.)

12,000

10,000

8,000

6,000

4,000

2,000

20 40

110

200

211310

220 222

321 400

Inte

nsity

of d

iffra

cted

bea

m (c

ps)

Diffraction angle 260 80 100 120 140 160

0

Figure 3.31Record of the diffraction angles for a tungsten sample obtained by theuse of a diffractometer with copper radiation.(After A. G. Guy and J. J. Hren, Elements of Physical Metallurgy, 3d ed., Addison-Wesley, 1974, p. 208.)

smi02334_ch03.qxd 4/21/03 3:38 PM Page 103

will be considered. The analysis of x-ray diffraction data for cubic unit cells canbe simplified by combining Eq. 3.4,

dhkl =a

h2 + k2 + l2with the Bragg equation = 2d sin , giving

= 2a sin h2 + k2 + l2 (3.11)

This equation can be used along with x-ray diffraction data to determine if acubic crystal structure is body-centered or face-centered cubic. The rest of thissubsection will describe how this is done.

To use Eq. 3.11 for diffraction analysis, we must know which crystal planesare the diffracting planes for each type of crystal structure. For the simple cubiclattice, reflections from all (hkl) planes are possible. However, for the BCC struc-ture diffraction occurs only on planes whose Miller indices when added together(h + k + l ) total to an even number (Table 3.6). Thus, for the BCC crystal struc-ture the principal diffracting planes are {110}, {200}, {211}, etc., which are listedin Table 3.7. In the case of the FCC crystal structure, the principal diffractingplanes are those whose Miller indices are either all even or all odd (zero is con-


Table 3.6 Rules for Determining the Diffracting {hkl} Planes in Cubic Crystals

Bravais lattice Reflections present Reflections absentBCC (h + k + l) = even (h + k + l) = oddFCC (h, k, l) all odd or all even (h, k, l) not all odd or all even

Table 3.7 Miller Indices of the Diffracting Planes for BCC and FCC Lattices

Cubicplanes Sum{hkl} h2 + k2 + l2 [h2 + k2 + l2] FCC BCC

{100} 12 + 02 + 02 1{110} 12 + 12 + 02 2 110{111} 12 + 12 + 12 3 111{200} 22 + 02 + 02 4 200 200{210} 22 + 12 + 02 5{211} 22 + 12 + 12 6 211 7

{220} 22 + 22 + 02 8 220 220{221} 22 + 22 + 12 9{310} 32 + 12 + 02 10 310

Cubicdiffracting

planes {hkl}

smi02334_ch03.qxd 4/21/03 3:38 PM Page 104


sidered even). Thus, for the FCC crystal structure the diffracting planes are{111}, {200}, {220}, etc., which are listed in Table 3.7.Interpreting Experimental X-Ray Diffraction Data for Metals with CubicCrystal Structures We can use x-ray diffractometer data to determine crystalstructures. A simple case to illustrate how this analysis can be used is todistinguish between the BCC and FCC crystal structures of a cubic metal. Let usassume that we have a metal with either a BCC or an FCC crystal structure andthat we can identify the principal diffracting planes and their corresponding 2values, as indicated for the metal tungsten in Fig. 3.3.

By squaring both sides of Eq. 3.11 and solving for sin2 , we obtain

sin2 = 2(h2 + k2 + l2)

4a2(3.12)

From x-ray diffraction data we can obtain experimental values of 2 for a seriesof principal diffracting {hkl} planes. Since the wavelength of the incoming radi-ation and the lattice constant a are both constants, we can eliminate these quan-tities by forming the ratio of two sin2 values as

sin2 Asin2 B

= h2A + k2A + l2A

h2B + k2B + l2B(3.13)

where A and B are two diffracting angles associated with the principal diffract-ing planes {h Ak AlA} and {h BkBlB}, respectively.

Using Eq. 3.13 and the Miller indices of the first two sets of principal dif-fracting planes listed in Table 3.7 for BCC and FCC crystal structures, we candetermine values for the sin2 ratios for both BCC and FCC structures.

For the BCC crystal structure the first two sets of principal diffracting planesare the {110} and {200} planes (Table 3.7). Substitution of the Miller {hkl}indices of these planes into Eq. 3.13 gives

sin2 Asin2 B

= 12 + 12 + 02

22 + 02 + 02 = 0.5 (3.14)

Thus, if the crystal structure of the unknown cubic metal is BCC, the ratio ofthe sin2 values that correspond to the first two principal diffracting planes willbe 0.5.

For the FCC crystal structure the first two sets of principal diffracting planesare the {111} and {200} planes (Table 3.7). Substitution of the Miller {hkl} in-dices of these planes into Eq. 3.13 gives

sin2 Asin2 B

= 12 + 12 + 12

22 + 02 + 02 = 0.75 (3.15)

Thus, if the crystal structure of the unknown cubic metal is FCC, the ratio ofthe sin2 values that correspond to the first two principal diffracting planes willbe 0.75.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 105


EXAMPLE PROBLEM 3.16

Example Problem 3.16 uses Eq. 3.13 and experimental x-ray diffractiondata for the 2 values for the principal diffracting planes to determine whetheran unknown cubic metal is BCC or FCC. X-ray diffraction analysis is usuallymuch more complicated than Example Problem 3.16, but the principles usedare the same. Both experimental and theoretical x-ray diffraction analysis hasbeen and continues to be used for the determination of the crystal structure ofmaterials.

An x-ray diffractometer recorder chart for an element that has either the BCC or theFCC crystal structure shows diffraction peaks at the following 2 angles: 40, 58, 73,86.8, 100.4, and 114.7. The wavelength of the incoming x-ray used was 0.154 nm.

(a) Determine the cubic structure of the element.(b) Determine the lattice constant of the element.(c) Identify the element. Solution(a) Determination of the crystal structure of the element. First, the sin2 values are

calculated from the 2 diffraction angles.

Next the ratio of the sin2 values of the first and second angles is calculated:

sin2 sin2

= 0.1170.235

= 0.498 0.5

The crystal structure is BCC since this ratio is 0.5. If the ratio had been 0.75, the structure would have been FCC.

(b) Determination of the lattice constant. Rearranging Eq. 3.12 and solving fora2gives

a2 = 2

4h2 + k2 + l2

sin2 (3.16)

or

a = 2

h2 + k2 + l2

sin2 (3.17)

2(deg) (deg) sin sin2 40 20 0.3420 0.117058 29 0.4848 0.235073 36.5 0.5948 0.353886.8 43.4 0.6871 0.4721

100.4 50.2 0.7683 0.5903114.7 57.35 0.8420 0.7090

smi02334_ch03.qxd 4/21/03 3:38 PM Page 106

3.12 Summary 107

Substituting into Eq. 3.17 h = 1, k = 1, and l = 0 for the h, k, l Miller indicesof the first set of principal diffracting planes for the BCC crystal structure,which are the {110} planes, the corresponding value for sin2 , which is 0.117,and 0.154 nm for , the incoming radiation, gives

a = 0.154 nm2

12 + 12 + 02

0.117= 0.318 nm

(c) Identification of the element. The element is tungsten since this element has alattice constant of 0.316 nm and is BCC.

3.12 SUMMARYAtomic arrangements in crystalline solids can be described by a network of lines called aspace lattice. Each space lattice can be described by specifying the atom positions in arepeating unit cell. There are seven crystal systems based on the geometry of the axiallengths and interaxial angles of the unit cells. These seven systems have a total of 14 sub-lattices (unit cells) based on the internal arrangements of atomic sites within the unitcells.

In metals the most common crystal structure unit cells are: body-centered cubic(BCC), face-centered cubic (FCC), and hexagonal close-packed (HCP) (which is a densevariation of the simple hexagonal structure).

Crystal directions in cubic crystals are the vector components of the directionsresolved along each of the component axes and reduced to smallest integers. They are in-dicated as [uvw]. Families of directions are indexed by the direction indices enclosed bypointed brackets as uvw. Crystal planes in cubic crystals are indexed by the reciprocalsof the axial intercepts of the plane (followed by the elimination of fractions) as (hkl).Cubic crystal planes of a form (family) are indexed with braces as {hkl}. Crystal planesin hexagonal crystals are commonly indexed by four indices h, k, i, and l enclosed inparentheses as (hkil). These indices are the reciprocals of the intercepts of the plane on thea1 , a2 , a3 , and c axes of the hexagonal crystal structure unit cell. Crystal directions inhexagonal crystals are the vector components of the direction resolved along each of thefour coordinate axes and reduced to smallest integers as [uvtw].

Using the hard-sphere model for atoms, calculations can be made for the volume,planar, and linear density of atoms in unit cells. Planes in which atoms are packed astightly as possible are called close-packed planes, and directions in which atoms are inclosest contact are called close-packed directions. Atomic packing factors for differentcrystal structures can also be determined by assuming the hard-sphere atomic model.Some metals have different crystal structures at different ranges of temperature and pres-sure, a phenomenon called polymorphism.

Crystal structures of crystalline solids can be determined by using x-ray diffractionanalysis techniques. X-rays are diffracted in crystals when the Braggs law(n = 2d sin ) conditions are satisfied. By using the x-ray diffractometer and the pow-der method, the crystal structure of many crystalline solids can be determined.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 107


3.13 DEFINITIONSSec. 3.1Crystal: a solid composed of atoms, ions, or molecules arranged in a pattern that is

repeated in three dimensions.Crystal structure: a regular three-dimensional pattern of atoms or ions in space.Space lattice: a three-dimensional array of points each of which has identical

surroundings.Lattice point: one point in an array in which all the points have identical

surroundings.Unit cell: a convenient repeating unit of a space lattice. The axial lengths and axial

angles are the lattice constants of the unit cell.Sec. 3.3Body-centered cubic (BCC) unit cell: a unit cell with an atomic packing arrangement

in which one atom is in contact with eight identical atoms located at the corners of animaginary cube.

Face-centered cubic (FCC) unit cell: a unit cell with an atomic packing arrangementin which 12 atoms surround a central atom. The stacking sequence of layers of close-packed planes in the FCC crystal structure is ABCABC. . . .

Hexagonal close-packed (HCP) unit cell: a unit cell with an atomic packingarrangement in which 12 atoms surround a central identical atom. The stackingsequence of layers of close-packed planes in the HCP crystal structure is ABABAB. . . .

Atomic packing factor (APF): the volume of atoms in a selected unit cell divided bythe volume of the unit cell.

Sec. 3.5Indices of direction in a cubic crystal: a direction in a cubic unit cell is indicated by a

vector drawn from the origin at one point in a unit cell through the surface of the unitcell; the position coordinates (x, y, and z) of the vector where it leaves the surface ofthe unit cell (with fractions cleared) are the indices of direction. These indices,designated u, v, and w are enclosed in brackets as [uvw]. Negative indices areindicated by a bar over the index.

Sec. 3.6Indices for cubic crystal planes (Miller indices): the reciprocals of the intercepts

(with fractions cleared) of a crystal plane with the x, y, and z axes of a unit cube arecalled the Miller indices of that plane. They are designated h, k, and l for the x, y, andz axes, respectively, and are enclosed in parentheses as (hkl). Note that the selectedcrystal plane must not pass through the origin of the x, y, and z axes.

Sec. 3.9Volume density v: mass per unit volume; this quantity is usually expressed in Mg/m3

or g/cm3.Planar density p: the equivalent number of atoms whose centers are intersected by a

selected area divided by the selected area.Linear density t: the number of atoms whose centers lie on a specific direction on a

specific length of line in a unit cube.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 108

3.14 Problems 109

Sec. 3.10Polymorphism (as pertains to metals): the ability of a metal to exist in two or more

crystal structures. For example, iron can have a BCC or an FCC crystal structure,depending on the temperature.

3.14 PROBLEMS3.1 Define a crystalline solid.3.2 Define a crystal structure. Give examples of materials that have crystal structures.3.3 Define a space lattice.3.4 Define a unit cell of a space lattice. What lattice constants define a unit cell?3.5 What are the 14 Bravais unit cells?3.6 What are the three most common metal crystal structures? List five metals that

have each of these crystal structures.3.7 How many atoms per unit cell are there in the BCC crystal structure?3.8 What is the coordination number for the atoms in the BCC crystal structure?3.9 What is the relationship between the length of the side a of the BCC unit cell and

the radius of its atoms?3.10 Molybdenum at 20C is BCC and has an atomic radius of 0.140 nm. Calculate a

value for its lattice constant a in nanometers.3.11 Niobium at 20C is BCC and has an atomic radius of 0.143 nm. Calculate a value

for its lattice constant a in nanometers.3.12 Lithium at 20C is BCC and has a lattice constant of 0.35092 nm. Calculate a

value for the atomic radius of a lithium atom in nanometers.3.13 Sodium at 20C is BCC and has a lattice constant of 0.42906 nm. Calculate a

value for the atomic radius of a sodium atom in nanometers.3.14 How many atoms per unit cell are there in the FCC crystal structure?3.15 What is the coordination number for the atoms in the FCC crystal structure?3.16 Gold is FCC and has a lattice constant of 0.40788 nm. Calculate a value for the

atomic radius of a gold atom in nanometers.3.17 Platinum is FCC and has a lattice constant of 0.39239 nm. Calculate a value for

the atomic radius of a platinum atom in nanometers.3.18 Palladium is FCC and has an atomic radius of 0.137 nm. Calculate a value for its

lattice constant a in nanometers.3.19 Strontium is FCC and has an atomic radius of 0.215 nm. Calculate a value for its

lattice constant a in nanometers.3.20 Calculate the atomic packing factor for the FCC structure.3.21 How many atoms per unit cell are there in the HCP crystal structure?3.22 What is the coordination number for the atoms in the HCP crystal structure?3.23 What is the ideal c/a ratio for HCP metals?3.24 Of the following HCP metals, which have higher or lower c/a ratios than the

ideal ratio: Zr, Ti, Zn, Mg, Co, Cd, and Be?

smi02334_ch03.qxd 4/21/03 3:38 PM Page 109


3.25 Calculate the volume in cubic nanometers of the titanium crystal structure unitcell. Titanium is HCP at 20C with a = 0.29504 nm and c = 0.46833 nm.

3.26 Rhenium at 20C is HCP. The height c of its unit cell is 0.44583 nm and its c/aratio is 1.633. Calculate a value for its lattice constant a in nanometers.

3.27 Osmium at 20C is HCP. Using a value of 0.135 nm for the atomic radius ofosmium atoms, calculate a value for its unit-cell volume. Assume a packingfactor of 0.74.

3.28 How are atomic positions located in cubic unit cells?3.29 List the atom positions for the eight corner and six face-centered atoms of the

FCC unit cell.3.30 How are the indices for a crystallographic direction in a cubic unit cell

determined?3.31 Draw the following directions in a BCC unit cell and list the position coordinates

of the atoms whose centers are intersected by the direction vector:(a) [100] (b) [110] (c) [111]

3.32 Draw direction vectors in unit cubes for the following cubic directions:(a) [111] (b) [110] (c) [121] (d) [113]

3.33 Draw direction vectors in unit cubes for the following cubic directions:

3.34 What are the indices of the directions shown in the unit cubes of Fig. P3.34?

(a) [112] (c) [331] (e) [212] (g) [101] (i) [321] (k) [122](b) [123] (d) [021] ( f ) [233] (h) [121] ( j) [103] (l) [223]

x

y

z

g

fe

h

14

13

34

12

23

14

34

x

y

z

dc

b

a13

14

14

34

12

12

(a) (b)

Figure P3.34

3.35 A direction vector passes through a unit cube from the ( 34 , 0, 14 ) to the ( 12 , 1, 0)positions. What are its direction indices?

3.36 A direction vector passes through a unit cube from the (1, 0, 34 ) to the ( 14 , 1, 14 )positions. What are its direction indices?

3.37 What are the crystallographic directions of a family or form? What generalizednotation is used to indicate them?

3.38 What are the directions of the 100 family or form for a unit cube?

smi02334_ch03.qxd 4/21/03 3:38 PM Page 110

3.14 Problems 111

x

y

z34

34

13

13

13

23

dc

ab

a

d

ccc

b

x

y

z

23

23

14

1213

(a) (b)

d

Figure P3.44

3.39 What are the directions of the 111 family or form for a unit cube?3.40 What 110-type directions lie on the (111) plane of a cubic unit cell?3.41 What 111-type directions lie on the (110) plane of a cubic unit cell?3.42 How are the Miller indices for a crystallographic plane in a cubic unit cell

determined? What generalized notation is used to indicate them?3.43 Draw in unit cubes the crystal planes that have the following Miller indices:

3.44 What are the Miller indices of the cubic crystallographic planes shown inFig. P3.44?

(a) (111) (c) (121) (e) (321) (g) (201) (i) (232) (k) (312)(b) (102) (d) (213) ( f ) (302) (h) (212) ( j) (133) (l) (331)

3.45 What is the notation used to indicate a family or form of cubic crystallographicplanes?

3.46 What are the {100} family of planes of the cubic system?3.47 Draw the following crystallographic planes in a BCC unit cell and list the

position of the atoms whose centers are intersected by each of the planes:(a) (100) (b) (110) (c) (111)

3.48 Draw the following crystallographic planes in an FCC unit cell and list theposition coordinates of the atoms whose centers are intersected by each of theplanes:(a) (100) (b) (110) (c) (111)

3.49 A cubic plane has the following axial intercepts: a = 13 , b = 23 , c = 12 . Whatare the Miller indices of this plane?

3.50 A cubic plane has the following axial intercepts: a = 12 , b = 12 , c = 23 . Whatare the Miller indices of this plane?

3.51 A cubic plane has the following axial intercepts: a = 1, b = 23 , c = 12 . What arethe Miller indices of this plane?

smi02334_ch03.qxd 4/21/03 3:38 PM Page 111


3.52 Determine the Miller indices of the cubic crystal plane that intersects thefollowing position coordinates: (1, 0, 0); (1, 12 , 14 ); ( 12 , 12 , 0).

3.53 Determine the Miller indices of the cubic crystal plane that intersects thefollowing position coordinates: ( 12 , 0, 12 ); (0, 0, 1); (1, 1, 1).

3.54 Determine the Miller indices of the cubic crystal plane that intersects thefollowing position coordinates: (1, 12 , 1); ( 12 , 0, 34 ); (1, 0, 12 ).

3.55 Determine the Miller indices of the cubic crystal plane that intersects thefollowing position coordinates: (0, 0, 12 ); (1, 0, 0); ( 12 , 14 , 0).

3.56 Rodium is FCC and has a lattice constant a of 0.38044 nm. Calculate thefollowing interplanar spacings:(a) d111 (b) d200 (c) d220

3.57 Tungsten is BCC and has a lattice constant a of 0.31648 nm. Calculate thefollowing interplanar spacings:(a) d110 (b) d220 (c) d310

3.58 The d310 interplanar spacing in a BCC element is 0.1587 nm. (a) What is itslattice constant a? (b) What is the atomic radius of the element? (c) What couldthis element be?

3.59 The d422 interplanar spacing in an FCC metal is 0.083397 nm. (a) What is itslattice constant a? (b) What is the atomic radius of the metal? (c) What could thismetal be?

3.60 How are crystallographic planes determined in HCP unit cells?3.61 What notation is used to describe HCP crystal planes?3.62 Draw the hexagonal crystal planes whose Miller-Bravais indices are:

(a) (1011) (d) (1212) (g) (1212) ( j) (1100)(b) (0111) (e) (2111) (h) (2200) (k) (2111)(c) (1210) ( f ) (1101) (i) (1012) (l) (1012)

3.63 Determine the Miller-Bravais indices of the hexagonal crystal planes inFig. P3.63.

a1

a3

a2a2

a1

b

a c

a3

12

b

c

a a1

a3

a2a2

a1

a3

(a) (b)

Figure P3.63

smi02334_ch03.qxd 4/21/03 3:38 PM Page 112

3.14 Problems 113

(a) (b)

a3

a2

a3

a2 a1

a1

a3

a2

a3

a2 a1

a1

Figure P3.67

3.64 Determine the Miller-Bravais direction indices of the a1 , a2 , and a3directions.

3.65 Determine the Miller-Bravais direction indices of the vectors originating at thecenter of the lower basal plane and ending at the endpoints of the upper basalplane as indicated in Fig. 3.18d.

3.66 Determine the Miller-Bravais direction indices of the basal plane of the vectorsoriginating at the center of the lower basal plane and exiting at the midpointsbetween the principal planar axes.

3.67 Determine the Miller-Bravais direction indices of the directions indicated inFig. P3.67.

3.68 What is the difference in the stacking arrangement of close-packed planes in(a) the HCP crystal structure and (b) the FCC crystal structure?

3.69 What are the most densely packed planes in (a) the FCC structure and (b) theHCP structure?

3.70 What are the closest-packed directions in (a) the FCC structure and (b) the HCPstructure?

3.71 The lattice constant for BCC tantalum at 20C is 0.33026 nm and its density is16.6 g/cm3. Calculate a value for its atomic mass.

3.72 Calculate a value for the density of FCC platinum in grams per cubiccentimeter from its lattice constant a of 0.39239 nm and its atomic mass of195.09 g/mol.

3.73 Calculate the planar atomic density in atoms per square millimeter for thefollowing crystal planes in BCC chromium, which has a lattice constant of0.28846 nm: (a) (100), (b) (110), (c) (111).

3.74 Calculate the planar atomic density in atoms per square millimeter for thefollowing crystal planes in FCC gold, which has a lattice constant of 0.40788 nm:(a) (100), (b) (110), (c) (111).

3.75 Calculate the planar atomic density in atoms per square millimeter for the (0001)plane in HCP beryllium, which has a constant a = 0.22856 nm and a c constantof 0.35832 nm.

smi02334_ch03.qxd 4/21/03 3:38 PM Page 113


3.76 Calculate the linear atomic density in atoms per millimeter for the followingdirections in BCC vanadium, which has a lattice constant of 0.3039 nm:(a) [100], (b) [110], (c) [111].

3.77 Calculate the linear atomic density in atoms per millimeter for the followingdirections in FCC iridium, which has a lattice constant of 0.38389 nm:(a) [100], (b) [110], (c) [111].

3.78 What is polymorphism with respect to metals?3.79 Titanium goes through a polymorphic change from BCC to HCP crystal structure

upon cooling through 882C. Calculate the percentage change in volume whenthe crystal st

crystal structure and crystal geometry

Documents