crankshaft kit catalog • 2013 - qwikorder catalog 2013.pdf · 1410cc mitsubishi g12b engine. g1;...

25
Crankshaft Kit Catalog • 2013 Crankshaft Supply Co., Inc. Page 1 4/24/2013 Engine CI / CC Liters Cyl. Years Vin Code / Engine Model Description Forging numbers Wt. Part # ACURA 1.6 4 86-87 D16A1 Integra. Flywheel flange has six bolt holes. Neck diameter is .865". 36 80013 1.6 4 88-89 D16A1 Integra. Flywheel flange has six bolt holes. Neck diameter is .944". 32 80014 1.6 4 88-89 D16A1 Integra. Flywheel flange has eight bolt holes. Neck diameter is 1.102". 36 80015 1678cc 1.7 4 92-93 B17A1 DOHC, Integra GS-R, Vigor, V-TEC engine. 38 80016 1797cc 1.8 4 94-01 B18C1 B18C5 DOHC. Integra GS-R 94-01, R Type 97-01, V-TEC engine. 38 80017 1834cc 1.8 4 90-01 B18A1 B18B1 Integra - Except GS-R and V-TEC. 36 80018 2156cc 2.2 4 97 F22B1 CL - Crankshaft has a 16mm bolt hole in neck. 38 80019 2.5 5 92-94 G25A1 Vigor. 38 80020 2.5 5 95-98 G25A4 38 80020 2675cc 2.7 V6 87-90 C27A1 For engines with housing bore of 2.7165" and 14mm bolt hole in neck. Legend. 35 80021 3165cc 3.2 V6 96-97 6VD1 Isuzu engine used in SLX. Remove reluctor ring from old unit and install on new unit 37 92031 3.2 V6 91-95 C32A1 Legend. 40 80022 3.2 V6 96-98 C32A6 TL. 40 80022 3494cc 3.5 V6 98-99 6VE1 Isuzu engine used in SLX. Remove reluctor ring from old unit and install on new unit 40 92032 AMERICAN MOTORS / JEEP / WILLYS 4 39-73 Willys engine with straight dowel pin holes in the flywheel flange. Must specify if cam is chain driven rather than gear driven. 638121, 641127, 646318 53 64003 4 39-73 Willys engine with tapered dowel pin holes in flywheel flange. Must specify if cam is chain driven rather than gear driven. 638121, 641127, 646318 53 64001 2.5 4 83-86 B, U Length of neck is 2 1/2" long. 3239611, 3239811 38 39022 2.5 4 87-90 E, H, Z Length of neck is approximately 2 inches. 8933002904 40 39024 2.5 4 91-02 P Length of neck is approximately 2 inches. 8933002904 40 39025 151 2.5 4 80-83 B GM manufactured engine. 684, 777 30 18049 2.8 V6 83-84 X, Z GM manufactured engine with 2.494" mains. 504 48 18039 2.8 V6 85-86 W GM manufactured engine with 2.648" mains. 174, 216, 481, 817 48 18055 225 3.7 V6 02-07 K 53020967AB 46 19097 3.8 6 65-73 With flat flywheel flange. 3172216, 3172218R, 3188947, 31889117 68 39012 3.8 6 72-79 With centering ring on flywheel flange. 3214722 68 39013 4.0 6 87-90 3003453 62 39021 4.0 6 91-02 53010411, 53020767 62 39026 4.2 6 72-86 A, C With centering ring on flywheel flange. Neck length is approximately 2 1/2". RD67703, 3214723, 3235477 75 39015 4.2 6 87-90 C Neck length is approximately 2". 3727 48 39023 173 232 242 258 1590cc 3206cc 2456cc AMERICAN MOTORS / JEEP / WILLYS • AMERICAN MOTORS / JEEP / WILLYS • AMERICAN MOTORS / J ACURA • ACURA • ACURA • ACURA • ACURA • ACURA • ACURA • ACURA • ACURA • ACURA 134 150 Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Upload: lyduong

Post on 22-Mar-2018

296 views

Category:

Documents


1 download

TRANSCRIPT

Page 1: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 1 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

ACURA

1.6 4 86-87 D16A1 Integra. Flywheel flange has six bolt holes. Neck diameter is .865". 36 80013

1.6 4 88-89 D16A1 Integra. Flywheel flange has six bolt holes. Neck diameter is .944". 32 80014

1.6 4 88-89 D16A1 Integra. Flywheel flange has eight bolt holes. Neck diameter is 1.102". 36 80015

1678cc 1.7 4 92-93 B17A1 DOHC, Integra GS-R, Vigor, V-TEC engine. 38 80016

1797cc 1.8 4 94-01 B18C1 B18C5 DOHC. Integra GS-R 94-01, R Type 97-01, V-TEC engine. 38 80017

1834cc 1.8 4 90-01 B18A1 B18B1 Integra - Except GS-R and V-TEC. 36 80018

2156cc 2.2 4 97 F22B1 CL - Crankshaft has a 16mm bolt hole in neck. 38 80019

2.5 5 92-94 G25A1 Vigor. 38 80020

2.5 5 95-98 G25A4 38 80020

2675cc 2.7 V6 87-90 C27A1 For engines with housing bore of 2.7165" and 14mm bolt hole in neck. Legend. 35 80021

3165cc 3.2 V6 96-97 6VD1 Isuzu engine used in SLX. Remove reluctor ring from old unit and install on new unit 37 92031

3.2 V6 91-95 C32A1 Legend. 40 80022

3.2 V6 96-98 C32A6 TL. 40 80022

3494cc 3.5 V6 98-99 6VE1 Isuzu engine used in SLX. Remove reluctor ring from old unit and install on new unit 40 92032

AMERICAN MOTORS / JEEP / WILLYS

4 39-73Willys engine with straight dowel pin holes in the flywheel flange. Must specify if cam is chain driven rather than gear driven.

638121, 641127, 646318 53 64003

4 39-73Willys engine with tapered dowel pin holes in flywheel flange. Must specify if cam is chain driven rather than gear driven.

638121, 641127, 646318 53 64001

2.5 4 83-86 B, U Length of neck is 2 1/2" long. 3239611, 3239811 38 39022

2.5 4 87-90 E, H, Z Length of neck is approximately 2 inches. 8933002904 40 39024

2.5 4 91-02 P Length of neck is approximately 2 inches. 8933002904 40 39025

151 2.5 4 80-83 B GM manufactured engine. 684, 777 30 18049

2.8 V6 83-84 X, Z GM manufactured engine with 2.494" mains. 504 48 18039

2.8 V6 85-86 W GM manufactured engine with 2.648" mains. 174, 216, 481, 817 48 18055

225 3.7 V6 02-07 K 53020967AB 46 19097

3.8 6 65-73 With flat flywheel flange. 3172216, 3172218R, 3188947, 31889117 68 39012

3.8 6 72-79 With centering ring on flywheel flange. 3214722 68 39013

4.0 6 87-90 3003453 62 39021

4.0 6 91-02 53010411, 53020767 62 39026

4.2 6 72-86 A, C With centering ring on flywheel flange. Neck length is approximately 2 1/2".

RD67703, 3214723, 3235477 75 39015

4.2 6 87-90 C Neck length is approximately 2". 3727 48 39023

173

232

242

258

1590cc

3206cc

2456cc

AM

ER

ICA

N M

OTO

RS

/ JEE

P / W

ILLYS

• AM

ER

ICA

N M

OTO

RS

/ JEE

P / W

ILLYS

• AM

ER

ICA

N M

OTO

RS

/ J

AC

UR

A • A

CU

RA

• AC

UR

A • A

CU

RA

• AC

UR

A • A

CU

RA

• AC

UR

A • A

CU

RA

• AC

UR

A • A

CU

RA

134

150

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 2: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 2 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

287 4.7 V8 99-06 CRemove reluctor ring from old unit and install on new unit. This crankshaft kit fits applications for rod bearings with locating tabs.

53020683 55 19087

5.0 V8 70-71 With flat flywheel flange. 3195292, 3214724, 4487237 55 39018

5.0 V8 72-99 With centering ring on flywheel flange. 3195292, 3214724, 4487237 55 39019

5.2 V8 92-98 Chrysler Engine, standard transmission. 2658393, 3462387, 3751841 58 19052

5.2 V8 92-98 Chrysler Engine, automatic transmission. 2658393, 3462387, 3751841 58 19053

5.9 V8 70-71 N With flat flywheel flange. 3195292, 3214724, 4487237 55 39018

5.9 V8 72-99 N With centering ring on flywheel flange. 3195292, 3214724, 4487237 55 39019

5.9 V8 96-98 Z Grand Cherokee - Chrysler Engine, standard transmission 3418640, 4027169 66 19050

5.9 V8 96-98 Z Chrysler Engine, automatic transmission. 3418640, 4027169 66 19051

CHRYSLER / JEEP (Jeep see also American Motors)

86 1.4 4 77-84 1410cc Mitsubishi G12B engine. G1 25 99064

1.5 4 85-88 K 1468cc Mitsubishi G15B engine. Rod journal width is approximately 7/8" (.870"). G1 25 99070

1.5 4 87-94 A, X 1468cc Mitsubishi 4G15 engine. Rod journal width is approximately 3/4" (.787"). G1, T1 25 99071

1.6 4 71-88

Mitsubishi G32 engine. Timing gear fits flush to number one main journal. Neck has two keyways. Pilot hole adapter for automatic transmission is not furnished.

35 65003

1.6 4 71-88

Mitsubishi G32 engine. Crankshaft has step between timing gear and number one main journal. Neck has two keyways. Pilot hole adapter for automatic transmission is not furnished.

35 65004

1.6 4 89-90 Y, Z Mitsubishi 4G61 DOHC engine. 38 99093

1.8 4 89-94 1755cc Mitsubishi 4G37 engine with five bolt holes in the flywheel flange. 38 99094

1.8 4 92-02 1834cc Mitsubishi 4G93 engine with seven bolt holes in the flywheel flange. G93, 29, 31, 36 29 99095

2.0 4 79-82 5, U 1995cc Mitsubishi G52B engine. Main diameter is 2.362". G52 47 99072A

2.0 4 85-92 D, R, U & V Mitsubishi G63B SOHC engine. Neck length is 1 1/2". Flywheel flange has six bolt holes. GE, 64 38 99085

2.0 4 92-97

Mitsubishi 4G63 engine using flanged thrust bearing. Flywheel flange has seven bolt holes. Main thrust width located on number three main is 1.005". On 1997 verify thrust type.

35 99086

2.0 4 97-99 F

Mitsubishi 4G63 engine. Turbo application using thrust washers. Flywheel flange has seven bolt holes. Main thrust width located on number three main is 1.005". On 1997 verify thust type.

35 99086T

2.0 4 95 C Flywheel flange has eight bolt holes. Crankshaft has a reluctor ring machined into the front counter-weight. 4556721, 4557665, 4667755 37 19092

2.0 4 96-02 C, YFlywheel flange has eight bolt holes. The crankshaft has a reluctor ring machined into the front counter-weight.

4556721, 4557665, 4667755 37 19090

2.0 4 03-05This crankshaft has a bolt-on reluctor ring on the rear counterweight.Remove reluctor ring from old unit and istall on new unit.

AA, 04884106 37 19093

CH

RY

SLE

R / JE

EP

(Jeep see also Am

erican Motors) • C

HR

YS

LER

/ JEE

P (Jeep see also A

merican M

otors) • CH

RY

SLE

R / JE

EP

(Jeep se

97

107

121

304

318

360

89

JE

EP

/ WILLY

S • A

ME

RIC

AN

MO

TOR

S / JE

EP

/ WILLY

S • A

M

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 3: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 3 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

2.2 4 81-85 B, C, D & E Flywheel flange has six bolt holes. Will not fit Dakota truck with standard shift transmission. 5214738, 5214990 37 19067

2.2 4 86-88 C, D & EFlywheel flange has eight bolt holes. Neck diameter is .905" or approximately 7/8". Will not fit Dakota truck with standard shift transmission.

5214738, 5214990 37 19077

2.2 4 87-88 A Inter-cooled turbocharger. Steel crankshaft with neck diameter of .905". 4323814, 43292355 44 19081

2.2 4 89-94 Non turbo engine. Neck diameter us 1.003". Flywheel flange has eight bolt holes. 4448493 37 19078

2.2 4 89 Turbo engine with steel crankshaft. Neck diameter of 1.003" 25585 44 19082

2.4 4 85-88 Mitsubishi G64B engine. Main thrust width is 1.145" and located on number three main journal. 64 38 99089

2.4 4 93-05

Mitsubishi 4G64 engine. Main thrust width is 1.005" and located on number three main journal. Rod thrust width is 1.050". Main bearing set comes with flanged main bearing.

AT1, K 35 99088

2.4 4 93-05

Mitsubishi 4G64 engine. Main thrust width is 1.005" and located on number three main journal. Rod thrust width is 1.050". Main bearing set comes with thrust washers.

AT1, K 35 99088T

2.4 4 95-02 B & XDOHC, eight bolt hole flange. Crankshaft has notches cut in the number two counter-weight for electronic ignition. Non turbocharged engines only.

4621916 43 19096

2.4 4 03-08Crankshaft has a bolt on reluctor ring located at the rear main. Remove reluctor ring from old unit and install on new unit. Non turbocharged engines only.

04781590AA 44 19098

2.5 4 86-88 K Neck diameter is .866" or approximately 7/8". 4273232 39 19068

2.5 4 89-95 G & JCrankshaft fits both turbo and non turbo engines. Neck diameter is 1.003" or approximately 1". Front of number one main has three bolt holes for timing gear.

448176, 486176, 4483176, 4448486, 4448490 39 19069

2.5 4 91-02 P Dakota truck. 448176, 486176, 4483176, 4448486, 4448490 40 19070

2.5 V6 95-02 H & N 2497cc Mitsubishi 6G73 engine. T3A, T3D, T3F, T3G, T3L, 09N, 19N, 29, 72, 76, 79 34 99073

2.6 4 79-94 D, E, G, H Mitsubishi G54B engine. Main journal diameter is 2.362". FWD G54 49 99072A

2.6 4 79-94 D ,E, G, H Mistubishi G54B engine. Main journal diameter is 2.362". RWD G54 49 99072B

167 2.7 V6 98-06 R, U & V DOHC engine. J 41 19086

3.0 V6 87-05 3, H & S Mitsubishi 6G72 engine. Cast iron crankshaft. T3A, T3D, T3F, T3G, T3L, 09N, 19N, 29, 72, 76, 79 34 99073

3.0 V6 91-96 Mitsubishi 6G72 engine with turbocharger. Forged steel crankshaft. E1, TDC, 72, 72P1 37 99075

195 3.2 V6 98-03 J 24 Valve, SOHC, 60 degree Interference engine. A1D, B1A, 74K1,94062803G4 19088

201 3.3 V6 90-06 3, G, R, T & U 3654, 4483654 43 19076

156

ee also A

merican M

otors) • CH

RY

SLE

R / JE

EP

(Jeep see also Am

erican Motors) • C

HR

YS

LER

/ JEE

P (Jeep see also A

merican M

otors) • CH

RY

SLE

R / JE

EP

(Jeep see also A

135

153

181

148

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 4: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 4 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

3.5 V6 93-97 F & G 300M, SOHC, cast iron block. A1D, B1A, 74K1,94062803G4 45 19091

3.5 V6 98-06 G, K & M 300M, SOHC, Aluminum block. A1D, B1A, 74K1,94062803G4 45 19095

3.5 V6 07-10 G, K & M SOHC, Aluminum block. A1D, B1A, 74K1,94062803G4 45 19099

3.7 6 60-67 Centering ring diameter is 1 31/32". 284935, 2128492, 2264479 77 19019

3.7 6 68-78 Steel crankshaft with centering ring diameter of 2 5/32" and rod journal width of 1.225". 284935, 2128492, 2264479 77 19055

3.7 6 77-78 3698966 81 19056

3.7 6 75-87 Cast iron crankshaft with rod journal width of 1.000". 359886, 3698966, 4095246 78 19058

3.7 V6 02-07 K 53020957AB 46 19097

232 3.8 V6 91-06 L 6433, 4556433 48 19089

239 3.9 V6 87-05 M & X Rod thrust width is .885". Standard drive transmission requires pilot bushing. 4323738, 4323769 44 19075

287 4.7 V8 99-04 NRemove reluctor ring from old unit and install on new unit. This crankshaft kit fits applications for rod bearings with locating tabs.

53020683 55 19087

5.2 V8 62-79 Steel crankshaft.2128278, 2128869, 2268119, 2465747,

2532457, 2658278, 284386864 19044

5.2 V8 76-04 Cast iron crankshaft, standard transmission. 2658393, 2991345, 3462378, 3751841, 3751887 58 19052

5.2 V8 76-04 Cast iron crankshaft, automatic transmission. 2658393, 2991345, 3462378, 3751841, 3751887 58 19053

340 V8 68-73 Steel crankshaft.2128278, 2128869, 2268119, 2465747,

2532457, 2658278, 284386864 19060

345 5.7 V8 03-06 D Hemi engine. 53021300AA 59 19094

5.9 V8 89-02 Cummins Turbo Diesel engine. This crankshaft does not have a reluctor ring. 3907604, 3907804 130 3907804

5.9 V8 71-03 Standard drive transmission requires pilot bushing. 3418640, 4027169 66 19050

5.9 V8 71-03 Automatic transmission 3418640, 4027169 66 19051

5.9 V8 62-78 Steel crankshaft. Flywheel flange has a centering ring and six threaded bolt holes. 2206159 74 19028

5.9 V8 74-78 Cast iron crankshaft. Flywheel flange has six threaded bolt holes. 3462923, 3751877, 4027172 70 19063

V8 61-71 Steel crankshaft. Flywheel flange has a centering ring and six threaded bolt holes. 2206159 74 19028

V8 70-71 Cast iron crankshaft. Flywheel flange has six threaded bolt holes. 3462923, 3751877, 4027172 70 19063

400 6.6 V8 72-80 Cast iron crankshaft. Flywheel flange has six threaded bolt holes. 3462923, 3751877, 4027172 70 19063

413 V8 62-77 Steel crankshaft. Flywheel flange has a centering ring and six threaded bolt holes. 2206160 74 19046

318

A

merican M

otors) • CH

RY

SLE

R / JE

EP

(Jeep see also Am

erican Motors) • C

HR

YS

LER

/ JEE

P (Jeep see also A

merican M

otors) • CH

RY

SLE

R / JE

EP

(Jeep see also Am

erican Motors) •

225

360

361

383

215

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 5: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 5 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

7.2 V8 64-66 Steel crankshaft. Flywheel flange has a centering ring and six threaded bolt holes. 2206160 74 19046

7.2 V8 66-72 Steel crankshaft. Flywheel flange has a centering ring and six threaded bolt holes. 2206160 74 19046

7.2 V8 73-80 Cast iron crankshaft. 3698461, 3751888, 4027175-3 78 19065

488 8.0 V10 92-03 W Truck engine. 53005823, 53006840 82 19085

1.3 4 88-92 K 1324cc Mazda B3 engine. Neck diameter is .865". A301, B301, 301 23 93038

1.3 4 92-97 H 1324cc Mazda B3 engine. Neck diameter is 1.062". A301, B301, 301 23 93039

1.6 4 71-73Flywheel flange does not have a centering ring. This application is for Automotive ONLY. For Bobcat application

711MAD, 771MAC, 771MAE, 2731E, 2737E 32 25059

1.6 4 81-83 Year model is from 1981 to April of 1983. Front seal surface is 3/4" wide.

E1EE-AB, E3EE-AB, E3EE-AA 30 25060

1.6 4 83-86 Year model is from May of 1983 to 1986. Front seal surface is 9/16" wide. E4EE-AA, E3EE-AA 30 25065

1.6 4 87-90Mazda B6 SOHC engine. Year model is 1987 to October 1990. Neck length is 7/8" with a diameter of .865".

B630, B616 25 93037

1.6 4 91-95 Mazda B6 DOHC engine. Neck length is approximately 1 1/4" long with a diameter of 1.063". B6S7, B61K, B616 25 93046

1.8 4 72-78 1796cc Mazda engine. 290 48 93032

1.8 4 90-93 1839cc BP Mazda engine. Neck size is .865". BP01 28 93030

1.8 4 94-96 1839cc BP Mazda engine. Neck size is 1.063". B630, BP02, G6 28 93041

1.9 4 85-86 Rod journal size is 1.886". E5EE-BA 30 25067

1.9 4 87-99 Rod journal size is 1.728". E7EE-BB, FOEE-CC 30 25071

2.0 4 71-74 X 2000cc. 70HM-AKA, 72HM-JA 28 25047

2.0 4 79-82 2000cc Mazda engine. 3975 48 93033

2.0 4 82-88 C E2ZE-BA, E43E-AC, 1D, 2D 48 25066

2.0 4 93-05 3 ZTEC DOHC engine. 933N-R67, 938M-R67, 938M-R68 34 25097

2.0 4 93-99 1993cc FS Mazda engine. FS07, 15 37 93031

2.0 4 97-05 P SOHC, SPI engine. RFF7CE-AA 32 25096

133 2.2 4 89-92 2184cc F2 Mazda engine. F201 34 93035

2.3 4 74-81 A, B, T, W & Y 2300cc engine with two piece rear oil seal. 1D 40 25048

2.3 4 81-90 A, D, T, W & Z 2300cc engine with one piece rear oil seal. Single spark plug head engine. E2ZE-BA, E43E-AC, 1D, 2D 40 25066

2.3 4 84-94 R & X 2300cc HSC engine. E43EAB, E43AEC, E43GEAC 31 25068

2.3 4 89-00 M 2300cc dual spark plug head engine. Main journal diameter is 2.205". C-GS, E89E-AB, 2D 48 25081

2.3 4 01-06 D, H DOHC, Duratec engine. This crankshaft does not have a gear for balance shaft. RF1L5G 35 25101

2.3 4 03-09 Z DOHC, Duratec engine. This crankshaft has a gear for balance shaft. Escape, Milan, Focus ZX3 3L5G6303DA 25100

121

140

CH

RY

SLE

R / JE

EP

(Jeep

FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D •

110

81

FORD

440

116

98

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 6: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 6 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

2.5 4 86-91 D HSC engine. E63A-AA 30 25074

2.5 V6 93-96 B Mazda KL engine. Steel crankshaft with large center counterweight. KL01 43 93045S

2.5 V6 97-02 Mazda KL engine. Cast iron crankshaft with small center counterweight. KL07 37 93045

2.5 V6 95-02 L Duratec engine. F53E-6303-AB, 5019934 39 25095

2.5 4 98-01 C OHC Engine. RFF87E-AC 39 25082

2.8 V6 74-75 Flanged main bearing packed in kit. 74TM-AA, 76TM-AA, 78TM-AA, 78TM-CA, 82TM-HAA 36 25050

2.8 V6 76-79 Thrust washers packed in kit. 74TM-AA, 76TM-AA, 78TM-AA, 78TM-CA, 82TM-HAA 36 25049

2.8 V6 80-86 Flanged main bearing packed in kit. 74TM-AA, 76TM-AA, 78TM-AA, 78TM-CA, 82TM-HAA 36 25050

2.9 V6 86-90 To 5/10/90 86TM6303BA, 88TM6303BA, 91TM6303AA 36 25051

2.9 V6 90-92 From 5/10/90 86TM6303BA, 88TM6303BA, 91TM6303AA 36 25052

3.0 V6 86-94 U RF-E6AE-AH 38 25075

3.0 V6 95-06 U RF-F58E-6303AA 40 25076

3.0 V6 93-95 W Nissan VG30E engine. Neck has two keyways and a diameter of .985". 38 94044

3.0 V6 96-99 W Nissan VG30E engine. Neck has two keyways and a diameter of 1.262". 38 94048

3.0 V6 96-05 S 2966cc Duratec DOHC engine. F53E-6303-AB, 5019934 39 25095

3.0 V6 89-95 Y Yamaha engine. 37 25099

195 3.2 V6 93-95 P Yamaha engine. 37 25099

3.3 6 65-83 Crankshaft has seven main journals. 1H, 3H, 1HA, E1BE-BB 47 25026

3.3 6 81-83 With pep or pen trans 5/16" centering ring 3H 25061

201 3.3 V6 99-02 T Nissan VG33E engine. 94048

3.8 V6 82-83 Engine has two piece rear oil seal. E2AE-DB 36 25069

3.8 V6 83-95 Engine has one piece rear oil seal and front main journal width is 1.312". Rear wheel drive. N2AE-AF, N3AE-AA 36 25070

3.8 V6 88-95Front main journal width of 1.390" and rod bearing width of .666". Non supercharged engine only. Front wheel drive.

E2AE-A, E3AE-AA, E3DE-BB, E9DE-BB, F68EB-A 36 25083

3.8 V6 89-95 R Supercharged engine only. E9TE 46 25085

3.8 V6 96-00 Rod bearing width of .784". Non supercharged engine only. Front wheel drive.

F4SZ6303AX, F6ZZ6303AX, F68EAB 36 25090

3.9 6 65-75 1L, 1LA, 1LAB 60 25027

3.9 V6 01-07 6 RF4F2EAA 38 25102

4.0 V6 90-95 Neck has 3/8" long keyway and flywheel flange has six bolt holes.

C94HA, 90TM6303AA, 90TM6303AB 43 25053

4.0 V6 95-96 Neck has 1 1/4" long keyway and flywheel flange has six bolt holes. C94HA, 96TM6303AA 47 25087

4.0 V6 97-98 E Neck has 1 1/4" long keyway and flywheel flange has eight bolt holes. OHV Engine

C94HA, XL2E6303AA, 96TM6303AA, 97JM6303AA 47 25088

183

153

171

177

FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

244

200

232

240

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 7: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 7 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

4.0 V6 97-09 8-Bolt flywheel flange SOHC, light weight piston. X3ZE-BA, XL2E 25077

250 4.1 6 69-81 C & L C9DE-A, 2H, 2HA, 2HAB 65 25038

255 4.2 V8 80-82 D 1J, 2J 43 25062

256 4.2 V6 97-07 2 4196cc engine. RFF65EAC, RFF85EAC 46 25089

272 V8 55-58 EC 60 25004

4.6 V8 91-07 W

Romeo engine. Flywheel flange has six bolt holes and kit is packed with one flanged bearing and one thrust washer. This may replace a two flanged bearing main set.MS2007P/5M2007P

F1AE-AD, F65E6303BB, RFF1AE6303AD 50 25084

4.6 V8 93-01 V Steel crankshaft is fully counterweighted and flywheel flange has eight bolt holes. MS2198AL F8TECE 50 25098S

4.6 V8 96-04 X & 6Windsor engine, flywheel flange has six bolt holes. Kit is packed with three thrust washers.5M7296A/MS2202P

F65EBB18D, F65E6303BB 50 25092

4.6 V8 96-01 X & 6Windsor engine, flywheel flange has eight bolt holes and kit is packed with one flanged bearing and one thrust washer. MS2007P/5M2007P

RFF1AE6303AD, F65EBB18D, F65E6303BB 50 25093

4.6 V8 96-07 X & 6Windsor engine, flywheel flange has eight bolt holes and kit is packed with three thrust washers. Main set MS2202p/5M7296A

RFF1AE6303AD, F65EBB18D, F65E6303BB 50 25098

4.6 V8 02-05 WSOHC, aluminum block. Flywheel flange has six bolt holes and kit is packed with one flanged bearing and one thrust washer. Main set MS2198AL/.MS2259A

RFF65E6303BC 50 25086

289 V8 63-68 C2OZ, C3AE-N, C3OZ, 1M, 3M 43 25022

292 V8 55-66 Passenger car application, cast iron casting. EC 60 25004

300 4.9 6 65-97 B, E, Y, Z & 9 C5TE-F, C6TE-G, 1N, 1NA, 1NABC, 2N, 2NA, 2NABC 76 25029

5.0 V8 68-80 Except for 78-79 Lincoln Versailles. 2C, 2M, 2MA, DOZE-A 45 25039

5.0 V8 81-82 Crankshaft is equipped with a slinger at the rear seal surface for engines with two piece rear oil seal. E1AE-AA, 2MAE 43 25063

5.0 V8 83-00

Crankshaft does not have a slinger and is for engines with a one piece rear oil seal. Pilot hole depth is approximately .560". This part number is NOT to be used in engines with AODE electronic overdrive transmissions.

E7AE-AA, 2MAE 43 25064

5.4 V8 66-72 For heavy duty applications. Neck diameter is 1.750". C4TE-A, C6TE-B, C7TE-A, DOTE-A, D2TE-A 78 25031

5.4 V8 64-78 Medium duty applications. Pilot hole is .750" deep. Neck diameter is 1.375".

COAE-B, C3AE-A, C4AE-A, C5AE-A, EDD, 2T, 2TA 68 25030

5.4 V8 97-08 L,A,L 5398cc Triton engine. SOHC XL3E-BA, F75-E, F75-1E, F75EAE 52 25094

281

302

330

R

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 8: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 8 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

5.8 V8 70-74 Cleveland engine. 4M, 4MA 63 25043

5.8 V8 75-82 Modified engine. 1K, 1KA, 8M 63 25042

5.8 V8 69-83Windsor engine with two piece rear oil seal. 69-75 uses main set 5M981P / MS981P. Specify year when ordering.

3M, 3MA, 7M, 7MA 60 25040

5.8 V8 83-98 Windsor engine with one piece rear oil seal. E4AE-BA, 7M, 7MA 60 25072

352 V8 58-67 Pilot hole is .750" deep. COAE-B, C3AE-A, C4AE-A, C5AE-A, EDD, 2T, 2TA 68 25030

359 5.9 V8 73-78 Truck and heavy duty application, steel casting. C4TE-A, C6TE-B, C7TE-A, DOTE-A, D2TE-A 78 25031

360 5.9 V8 68-78 Pilot hole is .750" deep. COAE-B, C3AE-A, C4AE-A, C5AE-A, EDD, 2T, 2TA 68 25030

361 5.9 V8 64-78 Truck and heavy duty application, steel casting. C4TE-A, C6TE-B, C7TE-A, DOTE-A, D2TE-A 78 25031

363 6.0 V8 03-10 P 32V Turbo. International Power-Stroke VT365 Diesel 42832

370 6.1 V8 79-94 1V, 1VA, 1VAB 85 25055

389 6.4 V8 73-78 1 3/4" Pulley snout diameter C4TE-B, C6TE-C, C7TE-B, C7TE-EA, D2TE-EA 78 25032

390 6.4 V8 61-76 1 3/8" Pulley snout diameter

C1AE-A, C1AE-D, C2AE-D, C3AE-B, C3AE-C, C3AE-D, C3AE-E, C4AE-B, 2U, 2UA,

3U

71 25036

391 6.4 V8 64-78 1 3/4 " Pulley snout diameter C4TE-B, C6TE-C, C7TE-B, C7TE-EA, D2TE-EA 78 25032

400 6.6 V8 71-82 S & Z 5M, 5MA, 5MAB, 5MABC 68 25041

401 6.6 V8 59-79 Truck engine. Rod journal diameter is 2.710". C1TE-B, C2TE-A 94 25033

415 6.8 V10 97-08 S, Y 6751cc Triton engine. 67 25091

421 6.9 V8 83-87 International Navistar diesel truck engine. 1803420C1, 1805420C1 88 42830

427 V8 63-68 1 3/8" Pulley snout diameter

C1AE-A, C1AE-D, C2AE-D, C3AE-B, C3AE-C, C3AE-D, C3AE-E, C4AE-B, 2U, 2UA,

3U

71 25036

429 7.0 V8 79-95 Neck diameter is 1.750". D9TE-AA, D9TE6303BA 79 25079

7.3 V8 88-94 C, K & M International Navistar diesel truck engine. 1803420C1, 1805420C1 88 42830

7.3 V8 94-03 F International Navistar Power Stroke diesel truck engine.

1818200C2, 1818200C3, 1831140C1 88 42831

7.5 V8 68-78 A, C & J C8VE-A, 2Y, 2YA, 2YAB, 2YABC 84 25057

7.5 V8 79-83 G & L Crankshaft has rear oil slinger. 3Y, 3YA, 3YB 84 25058

7.5 V8 84-98 G & L Crankshaft does not have a rear oil slinger. 3Y, 3YA, 3YB 84 25080

475 7.8 V8 58-79 Rod journal diameter is 2.710". C1TE-B, C2TE-A 94 25033

477 7.8 V8 58-81 Rod journal diameter is 2.710". C1TE-B, C2TE-A 94 25033

534 8.8 V8 58-81 Truck engine. Rod journal diameter is 2.710". C1TE-C, C2TE-B 110 25034

GENERAL MOTORS

61 1.0 3 85-01 993cc Suzuki G10 engine. K 17 95055

GE

NE

RA

L M

351

445

FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

D • FO

RD

• FOR

460

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 9: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 9 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

81 1.3 4 95-01 1324cc Suzuki G13A and G13BA engines. 43 18 95057

1.5 4 85-87 1471cc Isuzu 4XC1 and 4XC1T engines. Flywheel flange has six bolt holes. KN7, KN8, KN9, 4127, 5330 22 92024

1.5 4 87-89 1471cc Isuzu 4XC1 and 4XC1T engines. Flywheel flange has eight bolt holes. KN, KN7, KN10, 73 22 92023

1.6 4 76-87 1140N 40 18057

1.6 4 76-87 7184N 40 18044

1.6 4 85-98 Toyota 4ALC and 4AFE engines. Flywheel flange has six bolt holes.

1AC, 3A, 4AC, 4AFE, 4ALC, 5A 19 96060

1.6 4 85-95 Toyota engine. Flywheel flange has eight bolt holes. Rod journal diameter is 1.574". E2, G2, O1, P3, Q5, 6 30 96061

1.6 4 88-92 Toyota 4AGE engine. Rod journal diameter is 1.653". Flywheel flange has eight bolt holes. E2, E5 30 96062

1.6 4 89-04 Suzuki G16, G16KC, G16KV engines. OK, X20, 119 24 95054

1.6 4 90-93 Isuzu 4XE1 engine. Rod journal diameter is 1.572" and main journal diameter is 2.044". KN2, KN5, KN7 22 92025

1.8 4 76-82 Neck has 2 keyways. Flywheel flange has six bolt holes. 40 92028

1.8 4 92-93 1809cc Isuzu 4XF1 engine. Geo Storm GSI. 92035

1.8 4 93-97 1762cc Toyota 7AFE engine. Geo Prism. 32 96085

1.8 4 98-06 8 1794cc Toyota 1ZZFE engine. Geo Prism and Pontiac Vibe. 34 96086

1.8 4 01-06 L 1796cc Toyota 2ZZGE engine. Geo Prism and Pontiac Vibe. 31 96073

1.8 4 1982 G Crankshaft has rear seal oil slinger. 8705N, 14018705 34 18050

1.8 4 82-86 J & O OHC engine. R90155143, R90156143 34 47029

1.9 4 82-85 Isuzu G200Z engine. 40 92028

1.9 4 91-92 2100883, 210005833, 210008673 27 18090

1.9 4 93-98 2100883, 210005833, 210008673 27 18091

1.9 4 98-04 2100757AA2, 210092355 35 18094

2.0 4 82-84 B & P OHV engine with a two piece rear oil seal. 3278N, 14033278 34 18053

2.0 4 84-86 P OHV engine with a one piece rear oil seal. 3278N, 7243N, 7248N 34 18054

2.0 4 87-89 I OHV engine with a reluctor ring for distributor-less ignition.

L3, 003K, 003N, 900003C, 10103606 34 18063

2.0 4 87-91 K & M OHC engine. R9028036, R90280395, R960280399, 2670 40 47030

2.0 4 92-95 HOHC engine. Front counterweight has two protruding steel pins for electronic ignition and three bolt holes on top for detachable reluctor ring.

399, 2670, 90409507 40 47031

MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

110

112

119

121

92

98

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 10: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 10 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

2.2 4 90-97 G & 4 OHV engine. L3, 1237, 4618 34 18079

2.2 4 98-04 H, 4 & 5 OHV engine. L3, 1237, 4618 34 18093

2.2 4 00-06 F DOHC Ecotec engine. 7327 40 18095

2.3 4 87-88 D

Quad 4 engine. Notches on reluctor ring are approximately one inch from casting line down the center of crankshaft. Remove oil pump drive gear / sprocket from old unit and install on new unit.

22532120 40 41010

2.3 4 89-94 A, D & 3

Quad 4 engine. Notches on reluctor ring line up with the casting line down the center of crankshaft. Remove oil pump drive gear/sprocket from old unit and install on new unit.

22532120, 22545690, 22582120, 24574115 40 41011

2.3 4 95 D Dohc Quad 4 Remove oil pump drive sprocket from old unit and install on new unit. 24574115 40 41012

146 2.4 4 96-04 T2392cc LD9 Quad 4 DOHC engine. Remove oil pump drive gear/sprocket from old unit and install on new unit.

4620 50 41013

2.5 4 79-84 R Bushing not included 684, 777 30 18049

2.5 4 85-86 E & R Bushing not included 017, 684, 777 30 18065

2.5 4 85-86 U Bushing not included 771 30 18064

2.5 4 87-88 E & R Crankshaft has a reluctor ring for distributorless ignition. Bushing not included 381, 405, 543 30 18066

2.5 4 88-93 A, E & RCrankshaft has a reluctor ring and a 78 tooth oil pump/balancer drive gear. Overall length of crankshaft is 21 3/4". Bushing not included

405, 540, 543 34 18068

2.5 4 88-93 UCrankshaft has a reluctor ring and a 78 tooth oil pump/balancer drive gear. Overall length of crankshaft is 20 1/2". Bushing not included

406, 540 34 18076

153 4 62-70 May be used in some marine applications. 8522, 3788522, 379082N, 5743014 40 18040

2.8 V6 80-85 Z, 1 & 7 First design engine with small main block. Main journal diameter is 2.494". 264, 504 48 18039

2.8 V6 85-87 B, R, S, W & XSecond design engine with large main block. Main journal diameter is 2.648". This crankshaft used in externally balanced engine.

85, 174, 196, 817 48 18055

2.8 V6 87-89 S & W Crankshaft has a reluctor ring with notches for use in a distributorless internally balanced engine. 481, 526 40 18073

2.8 V6 87-93 R Used in a distributor type internally balanced engine. 526 40 18072

3.0 4 74-93 Marine application used in Mercruiser and OMC engines with a two piece rear oil seal.

N393775, N398776, N9341352 44 18098

3.0 4 94-99Marine application used in Mercruiser and OMC engines with a one piece rear oil seal. Rod thrust width is 1.035".

N14094623, 14096624 54 18099

3.0 V6 82-85 E Early engine with tall deck block and long connecting rods. 257, 404 40 14024

3.0 V6 85-88 L Late engine with short deck block and short connecting rods. 377, 732, 819 40 14027

3.0 V6 97-02 R Crankshaft has bolt on reluctor ring attached to the rear counterweight. 1255069, 90499243 41 18097

3.1 V6 88-05 D Crankshaft has a reluctor ring without notches for use in a distributor type engine. 981 40 18080

3.1 V6 88-05 J, M, T & V Crankshaft has a reluctor ring with notches for use in a distributorless engine. 17, 268, 981, 1X-148071 40 18077

194 6 62-67 3788424, 3820618N 55 18017

196 3.2 V6 78-80 229, 877, 1255674, 1257125, 1260877 40 14022

151

S

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

191

138

173

181

133

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 11: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 11 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

200 3.3 V6 78-79 726N, 1354N 42 18038

3.3 V6 89-90 N Flywheel flange has six bolt holes. 694 33 14029

3.3 V6 91-94 N Flywheel flange has eight bolt holes. 817, 4817, 25534817 34 14030

3.4 V6 91-05 E, S & X LA1, LQ1, L32 engines. Crankshaft has a reluctor ring with notches for use in a distributorless engine. 17, 268, 981, 1X-148071 40 18077

3.4 6 05-09 24x reluctor 64 42 18009

220 3.6 6 04-09 LY7 Cadillac CTS SRX 18002

225 3.7 V6 64-67 B Buick engine. 1255646, 1255845, 1357898, 1378351, 1378354 40 14020

229 3.8 V6 80-84 Chevrolet engine. 726N, 1354N 42 18038

230 3.8 6 62-70 Chevrolet engine. 3788424, 3820618N 55 18017

3.8 V6 64-77 C Odd firing engine. 1255646, 1255845, 1357898, 1378351, 1378354 40 14020

3.8 V6 77-87 A, 3 & 8Application is for rear wheel drive vehicles with the exception of the front wheel drive Riviera and Toronado with conventional mount engines.

229, 877, 1255674, 1257125, 1260877 40 14022

3.8 V6 84-88 B & 3 Front wheel drive vehicles with transverse mount engine. 267 40 14025

3.8 V6 89-90 C This engine is equipped with a cam driven balancer shaft. Flywheel flange has six bolt holes. 113, 502 40 14028

3.8 V6 90-93 L, C & 1 Series I engine. Flywheel flange has eight bolt holes. 309, 737, 4737 37 14031

3.8 V6 94 L & 1 Series I engine. Flywheel flange has eight bolt holes. 309, 737, 4737 37 14032

3.8 V6 95 C Series I engine. Flywheel flange has eight bolt holes. 309, 737, 4737 37 14033

3.8 V6 95-05 K, L & 1 Series II engine. 2170 36 14034

6 53-55 Crankshaft is packed with dowel-type main bearings. 3701488 86 18003

6 55-63Crankshaft is packed with locking lip type main bearings. (Dowel type on lower half and locking lip on top half).

3701488 86 18005

244 4.0 V8 95-03 3995cc engine with 14mm bolt hole in neck. 12554681 47 15019

4.1 6 66-76 D & Q Neck diameter is 1.250" and is not tapped. 407N, 460407, 3876802N 72 18028

4.1 6 77-84 460407 72 18045

4.1 V6 80-84Application is for rear wheel drive vehicles with the exception of the front wheel drive Riviera and Toronado with conventional mount engines.

229, 877, 1255674, 1257125, 1260877 40 14022

4.1 V8 82-91 Conventional mount engine with three bolt holes in the flywheel flange of the crankshaft. 1617590 45 15012

4.1 V8 84-91 Transverse mount engine with six bolt holes in the flywheel flange of the crankshaft.

1617590, 1629091, 1646737, 1648455 45 15013

O

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

N

GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

N

252

204

207

231

235

250

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 12: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 12 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

4.2 6 99-07 S Flywheel flange bolt holes are 10mm X 1.5.& 10mm X 1.0 Customer needs to match bolt pitch. 209, 866, 998 80 18018

4.2 6 08-09 60-2 teeth on the timing wheel 18019

260 V8 75-82 F 230376, 388766, 393654, 418882, 556607 52 41025

6 53-55 Crankshaft is packed with dowel-type main bearings. 3701488 86 18003

6 55-62Crankshaft is packed with locking lip type main bearings. (Dowel type on lower half and locking lip on top half).

3701488 86 18005

4.3 V6 84-86 N For engines with two piece rear oil seal. 1174, 14071174 40 18059

4.3 V6 86-99 Z

Heavy crankshaft used in all engines without balance shaft and in all VIN code Z with heavy piston and pin assemblies (745 grams). This crankshaft has two kwyways.

480, 640, 865, 5480, 5865, 8640, 10055480, 10105865,

1408864045 18060

4.3 V6 86-99 W, X & Z

Lightweight crankshafts used in 1992-99 VIN code W engine, some 1995 VIN code Z engine and the 1996-99 VIN code X engine have light piston and pin assemblies (675 grams). This crankshaft has a single keyway.

480, 685, 5480, 10055480, 10105865 45 18074

4.3 V6 98-05Crankshaft has a deep pilot hole depth of 1.410". Balance holes drilled in both the front and rear rod journal. RPO-ZK3 or ZN4 engines.

255 45 18085

4.3 V8 55-63 Chevrolet engine.3727449, 3734627, 3735236, 3815822, 3836266, 3876764

54 18007

4.3 V8 80-81 S Pontiac engine. 525887 45 47027

4.3 V8 94-96 W L99 engine. 10168568 18082

4.5 V8 88-92 Conventional mount engine with three bolt holes in the flywheel flange of the crankshaft. 1617590 45 15012

4.5 V8 88-92 3, 5 & 8 Transverse mount engine with six bolt holes in the flywheel flange of the crankshaft.

1617590, 1629091, 1646737, 1648455 45 15016

4.6 V8 93-99 Y & 9 Cadillac LD8 and L37 Northstar engine with 18mm bolt hole in neck. 3525774 3544669 46 15018

4.6 V8 00-03 Y & 9 Cadillac LD8 and L37 Northstar engine with 14mm bolt hole in neck. 12554681 46 15019

V8 55-63 Chevrolet engine.3727449, 3734627, 3735236, 3815822, 3836266, 3876764

54 18007

V8 64-67 Chevrolet engine. 3849847, 3876768 54 18008

4.8 6 60-66 Flywheel flange has 7/16" bolt holes and one dowel pin hole. 3884653 71 18023

4.8 6 67-90 Flywheel flange has 1/2" bolt holes and three dowel pin holes.

0363, 2774220N, 3299990, 3910363 71 18027

293 4.8 V8 99-05 VGEN III truck engine. For use in engines with rear flange width of .857" (7/8"). A new ignition reluctor ring is installed on the crankshaft.

12553482, 482 55 18087

300 4.9 V8 91-95 B Cadillac engine. 3520090 48 15017

301 4.9 V8 77-81 T, W & Y Pontiac engine. 525887 45 47027

5.0 V8 76-85 G, H & U Chevrolet engine, early model application with two piece rear oil seal. 3932442 59 18061

5.0 V8 86-04 E, F, G, H & M Chevrolet engine, late model application with one piece rear oil seal.

14088526, 14088535, 14088995 59 18056

5.0 V8 68-75 Chevrolet engine. 1130, 4672, 3911001, 3911001A, 3941174 56 18031

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

283

256

261

292

305

307

262

265

273

278

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 13: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 13 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

5.0 V8 80-90 Y & 9 Oldsmobile engine. 230376, 388766, 393654, 418882, 556607 52 41028

5.3 V8 99-06 B, C, M, P, T, Z

GEN III truck engine with rear flange width of .857" (7/8"). A new ignition reluctor ring is installed on the crankshaft.

12552216 55 18088

5.3 V8 07-up UGEN III LQ4, LQ9, Vortec 6000 truck engine with aluminun heads and a rear flange width of .857 (7/8"). 58 tooth reluctor.

12552216 55 18001

326 V8 67-75 Pontiac engine. 481397, 9773382, 9773383, 9783785, 9783786, 9793573 74 47019

V8 62-67 Chevrolet small journal engine with forged steel crankshaft. 2680. 4577, 3782680 56 18013

V8 68-74 Chevrolet large journal engine with cast iron crankshaft.

1130, 4672, 3911001, 3911001A, 3941174 56 18031

340 V8 66-67 Buick engine. 1235419, 1260718, 1261119, 1275809, 1378346 57 14018

5.7 V8 97-05 G, S GEN III engine with aluminum block and heads with a rear flange width of .857" (7/8"). A new ignition reluctor ring is installed on the crankshaft.

12552216, 12555089 55 18088

5.7 V8 07-up UGEN III LQ4, LQ9, Vortec 6000 truck engine with aluminun heads and a rear flange width of .857 (7/8"). 58 tooth reluctor.

12552216 55 18001

5.7 V8 67-85 Chevrolet engine. Heavy duty forged steel crankshaft and two piece rear oil seal. 1182, 2690 59 18033S

5.7 V8 68-80 R Oldsmobile engine. 230376, 388766, 393654, 418882, 556607 52 41028

5.7 V8 68-81 H, J & X Buick engine. 1235419, 1260718, 1261119, 1275809, 1378346 57 14018

5.7 V8 68-85 L Chevrolet engine. 310514, 3932442 59 18033

5.7 V8 67-75 M & P Pontiac engine with outside diameter of centering ring of 2.750".

4813, 481379, 481380, 496452 70 47019

5.7 V8 75-80 M & P Pontiac engine with outside diameter of centering ring of 2.490". 4813, 496452 70 47028

5.7 V8 86-01 J Chevrolet engine. Heavy duty forged steel crankshaft with one piece rear oil seal. 14088532 59 18075

5.7 V8 86-95 R Chevrolet engine. Late model with one piece rear oil seal.

14088526, 14088535, 14088995 59 18062

5.7 V8 92-97 P LT1 engine with one piece rear oil seal. 14088526, 14088535, 14088995 59 18078

5.7 V8 96-05 Vortec engine with one piece rear oil seal. 14088526, 14088535, 14088995 59 18056

6.0 V8 1999 U

GEN III LQ4 Vortec 6000 truck engine with cast iron cylinder heads and a rear flange width of 1.250" (1 1/4"). A new ignition reluctor ring is installed on the crankshaft.

12552215 55 18083

6.0 V8 00-05 U

GEN III LQ4, LQ9, Vortec 6000 truck engine with aluminun heads and a rear flange width of .857 (7/8"). A new ignition reluctor ring is installed on the crankshaft.

12552216 55 18088

6.0 V8 07-up UGEN III LQ4, LQ9, Vortec 6000 truck engine with aluminun heads and a rear flange width of .857 (7/8"). 58 tooth reluctor.

12552216 55 18001

6.0 V8 05-06 LS2GEN IV engine with aluminum block and heads with a rear flange width of .857" (7/8"). A new ignition reluctor ring is installed on the crankshaft.

12552216, 12555089 55 18088

R

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

327

350

365

307

346

325

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 14: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 14 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

6.0 V8 66-90 Steel crankshaft with a two piece rear oil seal. 6223, 7115, 9115 72 18026

6.0 V8 65-75 Chevrolet engine. Passenger car and light duty truck cast iron crankshaft with a two piece rear oil seal.

6223, 7115, 9115, 3874874, 3863144, 3904815 72 18035

6.0 V8 91-98 Cast iron crankshaft with a one piece rear oil seal. 10114187 71 18041

6.0 V8 91-98 Steel crankshaft with a one piece rear oil seal. 10114189 71 18041S

368 6.0 V8 80-84 6 & 9 Cadillac engine. Check forging number for identification. 1609142 67 15011

376 6.2 V8 07-UP LS2 GEN III LQ9 vortec rear flange .857 7/8" 58 tooth reluctor 12552216 55 18001

381 6.2 V8 82-91 Diesel engine with two piece rear oil seal. 14024236, 23500245 80 44830

383 V8

This is a special aftermarket application by grinding a 400 Chevrolet crankshaft to fit a 350 engine block. Customer must have a 400 Chevrolet crankshaft core for exchange.

3882841, 3951528, 3951529 59 18000

6.5 V8 92-94 Diesel engine with one piece rear oil seal. 23502592 80 44831

6.5 V8 92-02 Diesel engine with one piece rear oil seal. Fits both turbo and non turbo engines. 23502592 80 44831

396 V8 65-75 Chevrolet engine. Passenger car and light duty truck cast iron crankshaft with a two piece rear oil seal.

6223, 7115, 9115, 3874874, 3863144, 3904815 72 18035

V8 65-70 Chevrolet engine. Heavy duty steel forging crankshaft with two piece rear oil seal.

6223, 7115, 9115, 3874874, 3863144, 3904815 72 18026

V8 67-75 Pontiac engine with outside diameter of centering ring of 2.750".

4813, 481379, 481380, 496452 70 47019

400 6.6 V8 70-80 Chevrolet small block 400 engine. 3882841, 3951528, 3951529 58 18034

V8 75-80 Pontiac engine with outside diameter of centering ring of 2.490". 4813, 496452 70 47028

402 V8 70-75 Chevrolet engine with heavy duty forged steel crankshaft. 6223, 7115, 9115 72 18026

403 6.6 6.6 Liter, Duramax Diesel. 18092

403 V8 77-79 K Oldsmobile engine. 418882, 556607 52 41029

425 7.0 V8 77-79 S & T Cadillac engine. Check forging number for identification. 1609142 67 15014

V8 64-85 Chevrolet engine. Passenger car and light duty truck cast iron crankshaft.

6223, 7115, 9115, 387474, 3863144, 3904815 72 18035

V8 64-90 Chevrolet heavy duty steel forging with a two piece rear oil seal. 6223, 7115, 9115 72 18026

V8 91-98 Cast iron crankshaft with a one piece rear oil seal. 10114187 71 18041

V8 91-03 Steel forged crankshaft with a one piece rear oil seal. 10114189 71 18041S

429 v8 64-67 Cadillac 15020

430 V8 67-69 Buick engine. 1379242 74 14019

395

427

GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OT

366

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 15: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 15 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

7.4 V8 70-90 Chevrolet engine. Passenger car and light duty truck cast iron crankshaft with a two piece rear oil seal.

3521, 7416, N353039, 3875945, 3963524, 3967463 74 18036

7.4 V8 70-90 Chevrolet engine. Heavy duty steel forging with a two piece rear oil seal. 3521, 7416 74 18036S

7.4 V8 91-00 One piece rear oil seal. 10114188 74 18042

7.4 V8 91-01 Chevrolet engine with heavy duty steel forging for engines with a one piece rear oil seal. 14097044 74 18042S

V8 68-76 Oldsmobile engine. 230377, 230378, 397363, 400943 77 41022

V8 70-78 P, W, X & Y Pontiac engine. 496453, 9799103 80 47024

V8 70-76 B Buick engine. 1379242 74 14019

472 V8 68-74 R Cadillac engine. 1486424 86 15009

496 8.1 V8 01-06 G 8100 L18 Vortec truck engine. 430 85 18089

500 V8 70-76 Cadillac engine. 1495094, 1495095, 1496793 82 15010

HONDA

1.5 4 76-83 ED, EC, EM1 22 80003

1.5 4 84-87 EW1, EW3-4, D15A2-3

84-87 Civic 1500, 85-87 CRX Si & Civic Si, 84-87 CRX DX 25 80010

1.5 4 84-87 D15A1 Rod journal size 1.653", main journal size 1.771". Neck diameter is .865" 23 80012

1.5 4 88-95 D15B1-8 D15Z88-95 Civic, 88-91 CRX, 92-95 del SOL & V-TEC. Rod journal diameter 1.653", main journal diameter 1.771". Neck diameter is .944".

28 80023

1.5 4 88-95 D15B1-8 D15Z88-95 Civic, 88-91 CRX, 92-95 del SOL & V-TEC. Rod journal diameter 1.653", main journal diameter 1.771". Neck diameter is .865".

28 80024

1.5 4 90 D15B1 Rod journal diameter 1.496", main journal diameter 1.771". Neck diameter is .944". 25 80026

1.6 4 88-95 D16A6, D16Z688-91 Civic Si & CRX Si, 92-95 Civic & del SOL Si. Rod journal diameter 1.771", main journal diameter 2.165". Neck diameter is .865".

32 80013

1.6 4 88-00

D16A6, D16Z6, D16Y5,

D16Y7, D16Y8

88-91 Civic Si & CRX Si, 92-95 Civic & del SOL Si, 96-00 Civic, del SOL S, Civic EX V-TEC, del SOL Si, Civic HX. Rod journal diameter 1.771", main journal diameter 2.165". Neck diameter is .944"

32 80014

1595cc 1.6 4 94-00 B16A2, B16A3 94-00 Del Sol V-TEC, 96-00 Civic Si 34 80027

1599cc 1.6 4 76-78 EF, EG 76-78 Accord 22 80004

1.8 4 79-81 EK 79-81 Accord, 81 Prelude. Flywheel flange diameter is 2.913" with 10mm bolt holes. 35 80006

1.8 4 81-83 EK, EK1 81-83 Accord, 81-82 Prelude. Flywheel flange diameter is 2.992" with six 12mm bolt holes. 35 80005

1829cc 1.8 4 83-87 ES1-3, ET2, A18A1

83-87 Prelude, 84-85 Accord & Accord Sei, 11.5 mm bolt hole in the neck. Flywheel flange has eight 12mm bolt holes.

35 80007

2.0 4 86-89 BS, BT, A20A1-3

86-89 Accord & 86-87 Prelude . 11.5 mm bolt hole in neck 35 80007

2.0 4 86-89 BS, BT, A20A1-3

86-89 Accord & 86-87 Prelude. 14mm bolt hole in neck 34 80028

2.0 4 88-90 B20A3 88-90 Prelude SOHC engine. Rod journal diameter 1.771", main journal diameter 2.165". 40 80029

HO

ND

A • H

ON

DA

• HO

ND

A • H

ON

DA

• HO

ND

A • H

ON

DA

• HO

ND

A • H

ON

DA

• HO

ND

A • H

ON

DA

• HO

ND

A • H

ON

DA

• HO

ND

A •

1488cc

1493cc

1590cc

1751cc

1955cc

454

455

TO

RS

• GE

NE

RA

L MO

TOR

S • G

EN

ER

AL M

OTO

RS

• GE

NE

RA

L M

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 16: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 16 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

2.0 4 88-91 B20A588-91 Prelude DOHC engine. Rod journal diameter 1.889", main journal diameter 2.165" 13mm bolt hole in neck.

38 80009

2.0 4 88-91 B20A588-91 Prelude DOHC engine. Rod journal diameter 1.889", main journal diameter 2.165". 11mm bolt hole in neck.

38 80030

2.0 4 90-91 B21A1 90-91 Prelude. 13mm bolt hole in neck 38 80009

2.0 4 90-91 B21A1 90-91 Prelude. 11mm bolt hole in neck 38 80030

2.2 4 90-93 F22A1-4, F22A6

90-93 Accord, 91-93 Accord SE. 14mm bolt hole in neck. Stroke 3.74" 38 80008

2.2 4 92-97 F22A1, F22B1-2, F22B6

92-96 Prelude S, 95-97 Odyssey, 94-97 Accord, Accord V-TEC. 16mm bolt hole in neck. 38 80019

2157cc 2.2 4 93-96 H22A1 93-96 Prelude V-TEC. Rod journal diameter 1.889", main journal diameter 1.9685". Stroke 3.57". 42 80025

2259cc 2.3 4 92-93 H23A1 Prelude Si, 14mm bolt hole in neck. Mains 1.968" Rod 1.889" stroke 3.74" 38 80008

2.6 4 94-96 4ZE1 Isuzu Engine. 42 92027

2.6 4 95-02 4ZE1 Isuzu Engine. Remove reluctor ring off of old unit and install on new unit. 92029

2675cc 2.7 V6 87-97 C27A1 C27A4 For engines with housing bore of 2.7165". May require 14mm bolt. 35 80021

3.2 V6 94-95 6VD1 94-95 Passport. 37 92030

3.2 V6 96-02 6VD1 6VD1W Remove reluctor ring from old unit and install on new unit. 37 92031

3494cc 3.5 V6 98-04 6VE1 DOHC engine. Remove reluctor ring from old unit and replace on new unit. 40 92032

3638cc 3.5 V6 06-10 YF1, J35A9 SOHC VTEC, Pilot, Ridgeline 80031

HYUNDAI

1.5 4 86-89 G4AJ Excel. Rod journal width is .870". G1 25 99070

1.5 4 90-94 G4DJ Excel, Scoupe. Rod journal width is .787". G1,T1 25 99071

1.5 4 93 G4EK 93 Scoupe. Front seal surface diameter is 1.377". Neck is machined flat on two sides. D5 27 65020

1.5 4 94-95 G4EK 94-95 Scoupe. Front seal surface diameter is 1.377". 27 65021

1.5 4 95-00 G4EK 95-00 Accent. This shaft equipped with reluctor ring for distributorless ignitions. 28 65022

1595cc 1.6 4 92-95 G4CR 92-95 Elantra. 38 99092

1.8 4 96-98 G4GM96-98 Elantra, Tiburon. Centering ring of flywheel is 1.612" in diameter. Flange thickness is .818". Shaft has a bolt-on reluctor ring.

B1.8 38 99090

1.8 4 96-98 G4GM96-98 Elantra, Tiburon. Centering ring of flywheel is 1.378" in diameter. Flange thickness is .715". Shaft has a bolt-on reluctor ring.

B1.8 38 99091

1836cc 1.8 4 93-95 G4CN 93-95 Elantra. 38 99085

3165cc

1468cc

1495cc

1795cc

HO

ND

A • H

ON

DA

• HO

ND

A • H

ON

DA

• HO

ND

A • H

ON

DA

• HO

ND

A • H

ON

DA

• HO

ND

A • H

ON

DA

• HO

ND

A

1958cc

2056cc

2156cc

2559cc

HY

UN

DA

I • HY

UN

DA

I • HY

UN

DA

I • HY

UN

DA

I • HY

UN

DA

I • HY

UN

DA

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 17: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 17 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

2.0 4 97-02 G4GF97-'02 Elantra, Tiburon - Centering ring of flywheel is 1.612" in diameter. Flange thickness is .818". Shaft has bolt-on reluctor ring.

B2.0 38 99090

2.0 4 97-02 G4GF97-02 Elantra, Tiburon. Centering ring of flywheel is 1.378" in diameter. Flange thickness is .715". Shaft has bolt-on reluctor ring.

B2.0 38 99091

1997cc 2.0 4 92-03 G4CP 92-03 Sonata. Engine code "F". 38 99085

2.4 4 89-91 G4CS 89-91 Sonata. VIN Code "S". 64 38 99089

2.4 4 99-05 G4JS 99-05 Sonata, 01-04 Santa Fe 41 99088T

2.4 4 06-10 G6KB, G4KC 824 38 99097

2493cc 2.5 V6 99-01 V, G6BV Sonata. 99096

2656cc 2.7 V6 01-06 G6BA Santa Fe, Sonata, Tiburon, Tucson. 99096

2972cc 3.0 V6 90-98 G6AT 90-98 Sonata. 34 99073

3489cc 3.5 V6 02-05 E, G6CU XG350. 99077

INFINITI

1998cc 2.0 4 91-02 SR20DE 91-00 G20. 60J40, 43-D 40 94054

3.0 V6 90-92 VG30E 90-92 M30. 38 94044

3.0 V6 93-'97 VG30DE 93-97 J30. 30P43 38 94048

3.0 V6 96-01 VQ30DE 96-00 I30. 31U40 38 94063

4494cc 4.5 V8 90-96 VH45DE 90-96 Infinity Q45. 60U41 52 94064

ISUZU

1.5 4 85-89 4XC1, 4XC1T Flywheel flange has six bolt-holes. (See also 12670). 4127, 5330, KN7, KN10 22 92024

1.5 4 87-89 4XC1, 4XC1T I-Mark Turbo. Flywheel flange has eight bolt-holes. (See also 12550). 73, KN, KN7, KN10 22 92023

1.6 4 1989 4XE1W I-Mark. Main journal diameter is 1.887". 73, KN, KN7, KN10 22 92023

1.6 4 90-93 4XE1, 4XE1W Stylus, Impulse, Impulse Turbo. Main journal diameter is 2.044". KN2, KN5, KN7 22 92025

1809cc 1.8 4 92-93 4XF1 Impulse, Stylus. 92035

1817cc 1.8 4 81-85 G180Z I-Mark, Pickup. 40 92028

1949cc 1.9 4 83-87 G200, G200Z Trooper II, Impulse, Pickup. 40 92028

1994cc 2.0 4 85-89 4ZC1 Impulse turbo. 32 92034

2156cc 2.1 4 96-97 RJ1 Oasis. F22 Honda engine. 16mm snout bolt 38 80019

2.2 4 96-97 LN2

Hombre. GM engine. Parting edge of crankshaft is approximately 1/2" away from notch on the reluctor ring. This part number will not interchange with 12970.

1237, L3, 4618 34 18079

2.2 4 98-00 LN2Hombre. GM engine. Parting edge of crankshaft lines up next to notch on the reluctor ring. This part number will not interchange with 12740.

1237, L3, 4618 34 18093

2198cc 2.2 4 98-03 X22SE DOHC Engine. Daewoo W/ balance gear 2671 90530454, 93242486 48 92022

INFIN

ITI • INFIN

ITI • INFIN

ITI • INFIN

IISU

ZU • IS

UZU

• ISU

ZU • IS

UZU

• ISU

ZU • IS

UZU

• ISU

ZU • IS

UZU

• ISU

ZU • IS

UZU

• ISU

Z

1471cc

1588cc

2195cc

2960cc

1975cc

2350cc

A

I • HY

UN

DA

I • HY

UN

DA

I • HY

UN

DA

I • HY

UN

DA

I • HY

UN

DA

I • HY

UN

D

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 18: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 18 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

2254cc 2.3 4 86-95 4ZD1 86-95 Pickup, 86-87 Trooper II, 89-93 Amigo, 88-89 Impulse. AB 40 92026

2.6 4 88-94 4ZE1 Pickup, Trooper II, Amigo, Rodeo. 42 92027

2.6 4 95-97 4ZE1 Pickup, Trooper II, Amigo, Rodeo. Crankshaft has a bolt-on sensor ring at the rear main journal. 42 92029

2827cc 2.8 V6 89-92 Trooper II. GM engine. 481, 526 40 18073

3135cc 3.1 V6 91-94 CPC Pickup, Rodeo. GM engine. 981 40 18077

3.2 V6 92-95 6VD1 Trooper, Rodeo.7-Notch wheel 40 92030

3.2 V6 96-97 6VD1 96-97 1/2 Trooper, Rodeo. Remove reluctor ring from old unit and install on new unit. 40 92031

3.2 V6 98-02 6VD1W 97 1/2-02 Amigo, Rodeo. Remove reluctor ring from old unit and install on new unit. 40 92031

3494cc 3.5 V6 98-04 6VE1 98-02 Trooper - DOHC - VIN code "X". Remove reluctor ring from old unit and install on new unit. 40 92032

JEEP / AMERICAN MOTORS / WILLYS

4 39-73Willys engine with straight dowel pin holes in the flywheel flange. Must specify if cam is chain driven rather than gear driven.

638121, 641127, 646318 53 64003

4 39-73Willys engine with tapered dowel pin holes in flywheel flange. Must specify if cam is chain driven rather than gear driven.

638121, 641127, 646318 53 64001

2.5 4 83-86 B, U Length of neck is 2 1/2" long. 3239611, 3239811 38 39022

2.5 4 87-90 E, H, Z Length of neck is approximately 2 inches. 8933002904 40 39024

2.5 4 91-02 P Length of neck is approximately 2 inches. 8933002904 40 39025

151 2.5 4 80-83 B GM manufactured engine. 684, 777 30 18049

2.8 V6 83-84 X, Z GM manufactured engine with 2.494" mains. 504 48 18039

2.8 V6 85-86 W GM manufactured engine with 2.648" mains. 174, 216, 481, 817 48 18055

225 3.7 V6 02-07 K 53020967AB 46 19097

232 3.8 6 72-79 With centering ring on flywheel flange. 3214722 68 39013

4.0 6 87-90 3003453 62 39021

4.0 6 91-95 53010411, 53020767 62 39026

4.0 96-02 Automatic Only 53010411 , 53020767 62 39027

4.2 6 72-86 A, CWith centering ring on flywheel flange. Neck length is approximately 2 1/2" for engines with "V" type belts and pulleys.

RD67703, 3214723, 3235477 75 39015

4.2 6 87-90 C Neck length is approximately 2" for engines with serpentine type belt and pulley. 3727 48 39023

287 4.7 V8 99-06 CRemove reluctor ring from old unit and install on new unit. This crankshaft kit fits applications for rod bearings with locating tabs.

53020683 55 19087

5.0 V8 70-71 With flat flywheel flange. 3195292, 3214724, 4487237 55 39018

5.0 V8 72-99 With centering ring on flywheel flange. 3195292, 3214724, 4487237 55 39019

5.2 V8 92-98 Chrysler Engine, standard transmission. 2658393, 3462387, 3751841 58 19052

5.2 V8 92-98 Chrysler Engine, automatic transmission. 2658393, 3462387, 3751841 58 19053

150

173

242

258

304

318

JEE

P / A

ME

RIC

AN

MO

TOR

S / W

ILLYS

• JEE

P / A

ME

RIC

AN

MO

TOR

S / W

ILLYS

• JEE

P / A

ME

RIC

AN

MO

TOR

S / W

ILLYS

• JEE

P / A

ME

RIC

AN

M

134

ZU • IS

UZU

• ISU

ZU • IS

UZU

• ISU

ZU • IS

UZU

• ISU

ZU • IS

2559cc

3165cc

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 19: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 19 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

5.9 V8 70-71 N With flat flywheel flange. 3195292, 3214724, 4487237 55 39018

5.9 V8 72-99 N With centering ring on flywheel flange. 3195292, 3214724, 4487237 55 39019

5.9 V8 96-98 Z Grand Cherokee - Chrysler Engine, standard transmission. 3418640, 4027169 66 19050

5.9 V8 96-98 Z Chrysler Engine, automatic transmission. 3418640, 4027169 66 19051

KIA

1493cc 1.5 4 01-05 A5D Rio. A5 29 93050

1597cc 1.6 4 94-97 B6 Sephia - Mazda engine. B6S7, B61K, B616 25 93046

1793cc 1.8 4 98-04 T8 Sephia. Spectra 93049

1839cc 1.8 4 95-97 BP Sephia 95-97. VIN code 5. 28 93041

1998cc 2.0 4 95-00Mazda engine used in Sportage. Crankshaft flange has 8 bolt-holes and 1 dowel pin hole. DOHC engines only. Use MS8133P

FE50 32 93051

2.4 4 06-10 G6KB, G4KC 824 38 99097

2493cc 2.5 V6 2001 G6BV Optima. 99096

2656cc 2.7 V6 01-05 G6BA Optima. 99096

3489cc 3.5 V6 02-05 G6CU Sedona, Sorento. 99077

MAZDA

1489cc 1.5 4 95-98 Z5 Protégé. B3C7 23 93039

1.6 4 86-94 B6 323, Tracer SOHC engines. Neck approximately 7/8" long and .865" in diameter. B616, B630 25 93037

1.6 4 88-93 B6 323 GT Turbo & DOHC engines. Neck approximately 1 3/4" long and .865" in diameter. B630XD 25 93048

1.6 4 92-95 B6 MX3, Miata, 323. Neck approximately 1 1/4" long and 1.063" in diameter. B6S7, B616, B630, B61K 25 93046

1.6 4 99-02 ZM 99-02 Protégé B6S7, B616, B630, B61K 25 93046

1796cc 1.8 4 72-78 VB B1800 290 48 93032

1.8 4 90-93 BP05 Protégé - Neck diameter .865". BP01, 47, 48 28 93030

1.8 4 94-05 BP05 Protégé 94-98, Miata 94-05. Neck diameter 1.063" 22, G6, G7, NP, BP02, B630 28 93041

1844cc 1.8 V6 92-94 K8 MX3. 33 93047

1970cc 2.0 4 79-84 MA B2000, 626. U975, 3975 40 93033

1839cc

360

KIA

• KIA

• KIA

• KIA

• KIA

• KIA

• KIA

• KIA

• KIA

• KIA

• KIA

• KIA

1597cc

MA

ZDA

• MA

ZDA

• MA

ZDA

• MA

ZDA

• MA

ZDA

• MA

ZDA

• MA

ZDA

• M

M

OTO

RS

/ WILLY

S • JE

EP

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 20: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 20 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

2.0 4 93-03 FS 626, MX6. 15, FS07 37 93031

2.0 4 01-04 DOHC, ZETEC Engine. 01-02 626, 01-04 Tribute. 933M-R67, 938M-R67, 938M-R68 34 25097

1998cc 2.0 4 83-87 FE83-87 626, 85-87 B2000, 86-87 626 Turbo. Flywheel flange has six bolt holes. Crankshaft neck is approximately 1" in length.

FE01, FE50 48 93034

2184cc 2.2 4 87-99 F2 87-99 B2200, 88-92 626, 88-92 MX6. Also fits turbo. F201 34 93035

2255cc 2.3 V6 95-06 KJ Millenia. Crankshaft has a tapered neck. E1, F6, JLKJ, KL01 43 93044

2302cc 2.3 4 94-97 8A B2300, Ford engine. 2D, C-GS, E89E-AB 48 25081

2.5 V6 93-96 KL 626, MX6, Millenia. Steel crankshaft with large center counterweight. KL01 43 93045S

2.5 V6 97-02 KL KL engine. 626, Millenia. Cast iron crankshaft with small center counterweight. KL07 37 93045

2555cc 2.6 4 87-88 AM1 B2600 - Mitsubishi G54B engine. G54 49 99072B

2606cc 2.6 4 89-94 G6 B2600i, MPV. G601 37 93036

3.0 V6 88-98 MPV , 929 This crankshaft has no oil pump drive 43 93043

3.0 V6 88-98 MPV, 929. This crankshaft has a 3/4" wide oil pump drive block on the neck. 43 93042

3.0 V6 88-98 MPV, 929. This crankshaft has a 3/8" wide oil pump drive block on the neck. 43 93040

2967cc 3.0 V6 01-05 Ford Duratec - Tribute. F53E6303AB, 50119934 39 25095

2999cc 3.0 V6 94-99 8U B3000 - OHV Ford engine. RFE6AE-AH 38 25075

3996cc 4.0 V6 91-95 ZZL B4000 Navajo - Ford engine. 90TM6303AB 43 25053

MITSUBISHI

1410cc 1.4 4 78-84 G12B G1 25 99064

1.5 4 85-89 G15B, G4AJ 85-88 Mirage, 87-89 Precis, 86-89 Excel. Rod journal width is approximately .850 G1 25 99070

1.5 4 89-00 G15B, 4G15, G4DJ

89-00 Mirage, 90-94 Excel. Rod journal width is approximately .790. Front seal surface diameter is 1.181".

G1, T1 25 99071

1595cc 1.6 4 89-95 4G61, G4CR 89 Turbo Mirage, 91-92 Mirage. 38 99093

1.6 4 85-88 G32B Crankshaft neck has two keyways and the timing gear fits flush to the # 1 main journal. 35 65003

1.6 4 85-88 G32BCrankshaft neck has two keyways and the neck has a step between the timing gear and the # 1 main journal.

35 65004

1.8 4 89-94 4G37 Eclipse - The flywheel flange has five bolt-holes. 35 99094

1.8 4 92 4G33 L300 Van - The flywheel flange has five bolt-holes. 35 99094

1795cc 1.8 4 84-88 G62B, G4GM 5/84-88 Cordia & Tredia. Crankshaft neck length is approximately 1 1/2". 38 99085

1834cc 1.8 4 92-02 4G93 92-94 Expo, 92-96 Mirage. G93 29 99095

MITS

UB

ISH

I • MITS

UB

ISH

I • MITS

UB

ISH

I • MITS

UB

ISH

I • MITS

UB

ISH

I • MI

1597cc

1991cc

MA

ZDA

• MA

ZDA

• MA

ZDA

• MA

ZDA

• MA

ZDA

• MA

ZDA

• MA

ZDA

• MA

ZDA

• MA

ZDA

• MA

ZDA

• MA

ZDA

1755cc

2497cc

2954cc

1468cc

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 21: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 21 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

2.0 4 84-92 G63B, 4G63, G4CN, G4CP

5/84-88 Cordia, Tredia, 5/84-89 Pickup, 89-92 Eclipse & Galant. Crankshaft neck length is approximately 1 1/2". Flywheel flange has six bolt holes.

64, GE 38 99085

2.0 4 93-96 4G6393-94 Galant, Eclipse - 93-96 Eclipse turbo - Flywheel flange has 7 bolt holes. Main bearing set comes with flanged main bearing.

35 99086

2.0 4 95 420A Eclipse - Chrysler 16 valve, DOHC engine. Main bearings for 95 year model only. 4556721, 4557665, 4667755 37 19092

2.0 4 96-99 420A Eclipse - Chrysler 16 valve, DOHC engine. 4556721, 4557665, 4667755 37 19090

2.0 4 97-99 4G6397-99 Turbo engines use thrust washers instead of flanged bearing. Crankshaft flange has seven bolt holes.

35 99086T

2.4 4 85-92 G64B, G4CS 85-88 Galant, 85-92 Van, 90-92 Pickup, 89-92 Expo. Thrust width on # 3 main is 1.145". 64 38 99089

2.4 4 93-97 4G64, 4G64FR

95-96 Pickup, 95-97 Expo, Eclipse & Galant, 97-99 Montero Sport. Thrust width on # 3 main is 1.005". Rod thrust width is 1.050". This kit packed with flanged main bearings.

AT1, K 35 99088

2.4 4 98-02 4G64 98-02 Galant & Eclipse. This kit is packed with thrust washers. AT1, K 35 99088T

2555cc 2.6 4 79-89 G54B Montero, Pickup, Starion. G54 49 99072B

3.0 V6 88-04 6G7289-00 Montero & Pickup, 95-03 Montero Sport, 88-90 Galant Sigma, 92-99 Diamante, 90-95 Sonata, 91-99 3000GT. Cast iron crankshaft. VIN Codes H & P.

T3A, T3D, T3F, T3G, T3L, 29, 72, 76, 79, 09N, 19N 34 99073

3.0 V6 91-99 6G72 91-99 3000 GT Turbo. Steel crankshaft 72, 1, P1, TDC 37 99075

3496cc 3.5 V6 94-04 6G74, 6G74DN

94-02 Montero, 97-04 Montero Sport, 97-04 Diamante. Rod journal diameter is 2.165". 74K1, 94062803G4 44 99076

NISSAN

1.6 4 83-88 E16, EA16i 83-86 Sentra, 83-88 Pulsar. 31M 31 94040

1.6 4 87 CA16DE 87 Pulsar SE. Flywheel flange has eight bolt holes. D4240 32 94055

1.6 4 89-00 GA16i, GA16DE

89-00 Sentra, 91-94 NX, 89-90 Pulsar NX and 91-00 200SX. 4-0, 40-2, 77AS 29 94041

1.8 4 84-86 CA18ET 200SX Turbo. Flywheel flange has six bolt holes. D0242 32 94055

1.8 4 88-89 CA18DE Pulsar SE. Flywheel flange has eight bolt holes. D4240 32 94056

2.0 4 74-79 L20B 74-79 Pickup, 200SX, 510, 610 and 710. U6040 45 94057

2.0 4 80-86 Z20, Z20S, Z20E 80-81 510 and 200SX, 83-86 720 Pickup. U6040 45 94057

1974cc 2.0 4 82-89 CA20S, CA20E

82-85 Stanza, 84-89 200SX, 84-89 Stanza Wagon, 86-89 Stanza Sedan. D1742, 57E40 35 94046

1998cc 2.0 4 91-02 SR20DE 91-00 Sentra & 200SX, 91-94 NX. 43-D, 60J40 40 94054

2187cc 2.2 4 81-83 Z22, Z22E 81-83 720 Pickup, 81-83 200SX. 06W, 21-0, 90 45 94047

2972cc

ITS

UB

ISH

I • MITS

UB

ISH

I • MITS

UB

ISH

I • MITS

UB

ISH

I • MITS

UB

ISH

I • MITS

UB

ISH

I • MITS

UB

ISH

I • M

N

ISS

AN

• NIS

SA

N • N

ISS

AN

• NIS

SA

N • N

ISS

AN

• NIS

SA

N • N

ISS

AN

1597cc

1809cc

1952cc

2350cc

1997cc

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 22: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 22 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

2.4 4 83-90 Z24 83-90 720 Pickup, 86-90 Pathfinder, Van & D21 Pickup. 30W41, 30W42 45 94042

2.4 4 89-04 KA24E, KA24DE

89-99 240SX, 89-98 Stanza & Axxess, 90-97 Pickup, 93-00 Altima, 98-04 Frontier & Xterra. Crankshaft neck has two keyways. Flywheel flange has no centering ring.

86G 39 94050

2.4 4 89-04 KA24E, KA24DE

89-99 240SX, 89-98 Stanza & Axxess, 90-97 Pickup, 93-00 Altima, 98-04 Frontier & Xterra. Crankshaft neck has three keyways. Flywheel flange has no centering ring.

86G 39 94053

2.4 4 89-04 KA24E, KA24DE

89-99 240SX, 89-98 Stanza & Axxess, 90-97 Pickup, 93-00 Altima, 98-04 Frontier & Xterra. Crankshaft neck has three keyways. Flywheel flange has a centering ring.

40F 39 94051

2.4 4 89-04 KA24E, KA24DE

89-99 240SX, 89-98 Stanza & Axxess, 90-97 Pickup, 93-00 Altima, 98-04 Frontier & Xterra. Crankshaft neck has two keyways. Flywheel flange has a centering ring.

30R 39 94052

2.4 6 70-82 L24, L24E 70-73 240Z, 77-81 810, 81-6/82 Maxima. Rod journal diameter is 1.967". E3140, E3141, E3142 64 94058

2.4 6 82-84 L24E 7/82-84 Maxima. Rod journal diameter is 1.770". W3140 64 94059

2.5 4 02-07 QR25DE Altima, Sentra. Must reuse reluctor rIng from old crankshaft. 3 bolt reluctor ring. AE040 36 94060

2.5 4 02-07 QR25DE Altima, Sentra. Must reuse reluctor rIng from old crankshaft. 4 bolt reluctor ring. JA02H 36 94066

2753cc 2.8 6 74-83 L28E, L28ET 280Z, 280ZX. P-3040 64 94061

3.0 V6 84-87VG30i, VG30E, VG30ET

84-3/87 Maxima, 300ZX, 200ZX & Pickup, 84-89 300ZX Turbo. Neck has one keyway. 1181-36-4191 38 94043

3.0 V6 87-95VG30i, VG30E, VG30ET

SOHC engines. 4/87-94 Maxima, 4/87-99 300ZX & 200SX, 84-89 300XZ Turbo, 93-95 Quest & Villager, 4/87-95 Pickup & Pathfinder. Neck has two keyways and is .985" in diameter.

38 94044

3.0 V6 91-94 VG30DE

DOHC engines. 91-94 Maxima. Crankshaft has three keyways in the neck and one bolt-on counterweight located in the middle of the crankshaft. Flywheel flange has eight bolt-holes.

30P43 39 94049

3.0 V6 90-96 VG30DE VG30DETT

90-96 300ZX & 300ZX Turbo. Neck has two keyways and is 1.262" in diameter. Flywheel flange has eight bolt-holes. Shaft has one bolt-on counterweight located in the middle of the crankshaft.

30P43 38 94062

3.0 V6 95-01 VQ30DE DOHC engines. 95-01 Maxima. 31U40 38 94063

3.0 V6 96-98 VG30E96-98 Quest - Also fits 96-99 Mercury Villager - Neck has two keyways and is 1.262" in diameter. Flywheel flange has six bolt-holes.

38 94048

3275cc 3.3 V6 96-04 VG33E 96-02 Pathfinder, 99-02 Quest, 99-04 Frontier & Xterra. 38 94048

3498cc 3.5 V6 01-06 VQ35DE 350Z 03-06, Altima 02-06, Maxima 02-06 and Murano 03-06. 4W041 94065

SUBARU

1820cc 1.8 4 93-96 EJ18E Impreza. 25 84000

1999cc 2.0 4 02-05 EJ20T Rod diameter 2.046" thrust #5 main Turbo DOHC 25 84004

SU

BA

RU

• SU

BA

R

2960cc

N • N

ISS

AN

• NIS

SA

N • N

ISS

AN

• NIS

SA

N • N

ISS

AN

• NIS

SA

N • N

ISS

AN

• NIS

SA

N • N

ISS

AN

• NIS

SA

N • N

ISS

AN

• NIS

SA

N • N

ISS

AN

• NIS

SA

N • N

ISS

AN

• NIS

SA

N • N

IS

2389cc

2393cc

2488cc

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 23: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 23 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

2.2 4 90-98 EJ22E Impreza, Legacy, Outback. #3 Thrust 25 84000

2.2 4 99-UP EJ22E Rod diameter 2.046" #5 thrust. 25 84003

2457cc 2.5 4 96-98 EJ25 96-99 Legacy, 98 Impreza & Forester. Rod diameter is 1.889 and the thrust is located on main three. 25 84001

2458cc 2.5 4 99-07 EJ25I Impreza, Legacy, Forester. Rod diameter is 2.046" and main thrust is located in the number 5 position. 25 84002

SUZUKI

993cc 1.0 3 80-94 G10 85-88 Swift, - Also used in some GM vehicles. K 17 95055

1298cc 1.3 4 90-01 G13K, G13BB, G13BA 90-95 Samurai, 89-00 Swift. 043, 72, Y10 18 95057

1324cc 1.3 4 86-89 G13A 86-89 Samurai, 89 Sidekick. 43 18 95052

1590cc 1.6 4 89-02 G16KC, G16KV, G16B

89-98 Sidekick, 95-00 Esteem, 96-98 X90, 99-01 Vitara. 119, OK, X20 24 95054

1995cc 2.0 4 99-05 J20A 99-03 Vitara, 04-05 Forenza. Verify 6 or multi-tooth reluctor ring. 44 95058

1999cc 2.0 4 04-05 X2OSED, C2ONED 04-05 Forenza w/ Daewoo motor 2671, 608 48 92020

2494cc 2.5 V6 99-05 H25A 99-05 Grand Vitara, DOHC V6 24valve engine. 86 40 95059

2737cc 2.7 V6 01-07 H27A 01-05 XL7, 06-07 Grand Vitara. 86 40 95059

TOYOTA

1452cc 4 80-91 1AC, 3AC 80 thru 10/83. 1A, 3A, 4A, 5A 19 96060

1456cc 1.5 4 87-94 3E, 3EE 3E 39 96075

1.5 4 92-98 5EFE 92-98 Paseo, 95-98 Tercel. 3E 39 96075

1.5 4 00-05 1NZFE 00-05 Echo. 96095

1.6 4 83-88 4AC, 4ALC Corolla. Flywheel flange has six bolt holes. 1A, 3A, 4A, 5A 19 96060

1.6 4 85-87 4AGEC, 4AGELC

85-87 MR2, Corolla GTS. Flywheel flange has eight bolt holes. Rod journal diameter is 1.574". 30 96061

1.6 4 88-91

4AGE, 4AGEC, 4AGELC 4AGZE

88-89 MR2, 88-91 Corolla GTS. Flywheel flange has eight bolt holes. Rod journal diameter is 1.653". E2, E5, D6 30 96062

1.6 4 88-97 4AF, 4AFE 88-89 SR5, 88-97 Corolla, 90-92 Celica ST. 19 96060

1762cc 1.8 4 93-97 7AFE 93-97 Corolla, 94-97 Celica. 32 96085

1794cc 1.8 4 98-06 1ZZFE 98-06 Corolla, 00-06 Celica, MR2 and Matrix. 34 96086

1796cc 1.8 4 00-06 2ZZGE 00-05 Celica, 05-06 Corolla XRS, 03-06 Matrix. 31 96073

1995cc 2.0 4 83-86 2SELC 83-86 Camry, 85-86 Celica 40 96076

R

U • S

UB

AR

U • S

UB

AR

U • S

UB

A

S

UZU

KI • S

UZU

KI • S

UZU

KI • S

UZU

KI • S

UZU

KI • S

UZU

KI •

1587cc

1497cc

2212cc

TOY

OTA

• TOY

OTA

• TOY

OTA

• TOY

OTA

• TOY

OTA

• TOY

OTA

• TOY

OTA

• TOY

OTA

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 24: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 24 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

2.0 4 84-85 3YEC 3Y, Z21 34 96065

2.0 4 86-89 3SGTE, 3SGELC

86-89 Celica GTS. Flywheel flange has eight 10mm bolt holes. Crankshaft rear seal diameter is 3.346". 3SF 40 96077

2.0 4 87 3SFE Crankshaft rear seal size is 3.346". Flywheel flange has six bolt holes. 3SF 40 96079

2.0 4 88-91 3SFE 88-91 Camry, '88-'89 Celica. Flywheel flange has eight bolt holes. 3SF 40 96077

2.0 4 88-95 3SGTE 88-95 Celica Turbo, 90-95 MR2 turbo. Flywheel flange has eight 12mm bolt holes. Crankshaft rear seal size is 3.504". Steel crankshaft.

39 96072

2.0 4 96-00 3SFE 96-00 Rav 4 96082

2.0 4 03-06 1AZFE 01-03 Rav 4. 37 96088

2.2 4 90-01 5SFE90-99 Celica and MR2, 92-00 Camry, 98-00 Solera. Remove counter balance gear from old unit and install on new unit.

1341103010-D 41 96081

2.2 4 90-91 5SFE This crankshaft will not accommodate a counter balance gear. 41 96080

2189cc 2.2 4 3/82-84-1/2 20R 43 96063

2237cc 2.2 4 86-89 4YEC 3Y, Z21 34 96065

2362cc 2.4 4 01-07 2AZFE02-07 Camry, 01-07 Highlander, 04-05 Rav 4, 02-07 Solara. Remove counter balance shaft from old unit and put on new unit.

42 96094

2.4 4 3/82-84-1/2 22R 81-3/82 Celica, Corona, Pickup 43 96063

2.4 4 84-1/2 - 95

22R, 22RE, 22REC, 22RETC

3/82-95 Celica, Pickup, 4Runner and Corona. Bearings packaged for engines made after February '82.

43 96064

2438cc 2.4 4 90-042TZFE,

2TZFZE, 2RZFE

90-97 Previa, 95-97 Previa supercharged, 95-04 Tacoma RZ 45 96084

2507cc 2.4 V6 88-91 2VZFE 88-91 Camry, 90-91 Lexus ES250. 35 96070

2563cc 2.6 6 71-80 4M, 4ME 73-76 Corona MKII, 78-80 Cressida, 71-72 Crown and 79-80 Supra. 64 96066

2693cc 2.7 4 94-05 3RZFE 94-05 Tacoma, 4Runner and T100. RZ 49 96083

2.8 6 81-84 5ME, 5MGE 81-7/84 Cressida and Supra 2M, 4M 65 96066

2.8 6 84-88 5MGE 8/84-88 Cressida and Supra 2M, 4M 65 96067

2954cc 3.0 6 86-92 7MGE, 7MGTE 89-92 Cressida, 86-92 Supra and 87-92 Supra turbo. 6M, 7M 56 96078

3.0 V6 88-95 3VZE 88-95 Pickup, 4Runner and T100. Crankshaft neck length is 2.750". 40 96068

3.0 V6 92-93 3VZFE 92-93 Camry and Lexus ES300. Crankshaft neck length is 2.525". 44 96069

2995cc 3.0 V6 94-06 1MZFE 94-06 Camry, Avalon, Sienna, Solara and 94-03 Lexus ES300, RX300. 43 96071

2997cc 3.0 6 93-98 2JZGE, 2JZGTE

95-98 Supra, Supra turbo, 92-97 Lexus GS300 and SC300. 96090

3310cc 3.3 V6 03-07 3MZFE 03-07 Camry, Highlander, Sienna and Lexus RX330 and ES330. 96096

3378cc 3.4 V6 95-04 5VZFE 95-98 T100, 95-04 Tacoma, Tundra and 4Runner - VIN code N & V. 44 96087

3968cc 4.0 V8 90-00 1UZFE 90-00 Lexus GS400, LS400 60 96091

4293cc 4.3 V8 01-07 3UZFE Lexus LS430 and GS430. 96092

2164cc

2759cc

2366cc

1998cc

TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

YO

TA • TO

Y

2959cc

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com

Page 25: Crankshaft Kit Catalog • 2013 - QwikOrder CATALOG 2013.pdf · 1410cc Mitsubishi G12B engine. G1; 25 99064; 1.5 4; ... Mitsubishi 4G61 DOHC engine. 38; ... Crankshaft Kit Catalog

Crankshaft Kit Catalog • 2013

Crankshaft Supply Co., Inc. Page 25 4/24/2013

Engine CI / CC

Liters Cyl. Years Vin Code / Engine Model

Description Forging numbers Wt. Part #

4663cc 4.7 V8 98-07 2UZFELexus 98-07 LX470, 03-07 GX470. Toyota 03-07 4-Runner, 98-07 Landcruiser, 01-07 Sequoia, 99-07 Tundra.

96093

VOLKSWAGEN

1.8 98-05 AEB, AUG, AWM DOHC 20V Turbo 75003

2.8 V6 92-97 VR6 92-95 Jetta, Golf GTI, Passat GLX, 92-94 Corrado SLC reluctor ring 4.328" D21B, I438 48 75001

2.8 V6 92-97 VR6 92-95 Jetta,Golf GTI, Passat GLX,92-94 Corrado SLC reluctor ring 3.856" D21B, I438 48 75002

VO

LKS

WA

GE

N 2792cc

YO

TA • TO

Distributed by: Sterling Bearing: Kansas City, Minneapolis, Worcester 800/821-5148 www.sbi.qwik-order.com