cp124 clutch pumps - permco · clutch pump switch kit clutch pump service parts br549 clutch pump...

4
CP124 CLUTCH PUMP SERIES F EATURES q Cubic inch displacements from 0.62 through 2.48 q Speeds to 3000 RPM and pressures to 3500 PSI q SAE “A” mounting with bracket or Pad mounting available q Heavy duty sleeve bushing design in a small frame size q Doweled and high strength 3 piece cast iron construction q 100% factory tested q High strength alloy steel gear and shaft set q NPT, O’ring, or split flange porting located on the rear and/or side q Only high torque clutches used with all the popular clutch configurations available q Pressure balanced wear plates maintain high pump efficiency throughout all operating ranges q Typical applications include recovery vehicles, snow plows, spreaders, utility vehicles, winches, small hoists, aerial devices, lift gates, cranes, and light duty equipment GEAR DISPL GPM/LITERS MAX MIN MAX WIDTH (IN) CU IN/CC @ 1000 RPM RPM RPM PSI/BAR .50 .62/10 2.2/8.3 3000 600 3500/241 .75 .93/15 3.6/13.6 3000 600 3500/241 1.00 1.24/20 4.9/18.5 3000 600 3500/241 1.25 1.55/25 6.1/23.1 3000 600 3500/241 1.50 1.86/30 7.4/28.0 3000 600 3200/220 1.75 2.17/35 8.8/33.3 3000 600 2900/200 2.00 2.48/40 10.0/37.9 3000 600 2500/172 CP124 with Pad Mounting, Side and Rear Porting CP124 CLUTCH PUMPS AND ACCESSORIES CP124 CLUTCH PUMPS AND ACCESSORIES CP124 with Bracket Mount, Side SAE O'ring Ports

Upload: others

Post on 14-Oct-2020

26 views

Category:

Documents


1 download

TRANSCRIPT

Page 1: CP124 CLUTCH PUMPS - Permco · Clutch Pump Switch Kit CLUTCH PUMP SERVICE PARTS BR549 Clutch Pump Bracket for 2 Bolt "A" Mount 515376 8 Groove Type K Sepentine Clutch, 90 lb.ft.*

CP124 CLUTCH PUMP SERIES FEATURESq Cubic inch displacements from 0.62 through 2.48q Speeds to 3000 RPM and pressures to 3500 PSIq SAE “A” mounting with bracket or Pad mounting availableq Heavy duty sleeve bushing design in a small frame sizeq Doweled and high strength 3 piece cast iron constructionq 100% factory testedq High strength alloy steel gear and shaft setq NPT, O’ring, or split fl ange porting located on the rear and/or sideq Only high torque clutches used with all the popular clutch confi gurations availableq Pressure balanced wear plates maintain high pump effi ciency throughout all operating rangesq Typical applications include recovery vehicles, snow plows, spreaders, utility vehicles, winches, small hoists,

aerial devices, lift gates, cranes, and light duty equipment

GEAR DISPL GPM/LITERS MAX MIN MAX WIDTH (IN) CU IN/CC @ 1000 RPM RPM RPM PSI/BAR .50 .62/10 2.2/8.3 3000 600 3500/241 .75 .93/15 3.6/13.6 3000 600 3500/241 1.00 1.24/20 4.9/18.5 3000 600 3500/241 1.25 1.55/25 6.1/23.1 3000 600 3500/241 1.50 1.86/30 7.4/28.0 3000 600 3200/220 1.75 2.17/35 8.8/33.3 3000 600 2900/200 2.00 2.48/40 10.0/37.9 3000 600 2500/172

CP124 with Pad Mounting,

Side and Rear Porting

CP124 CLUTCH PUMPS AND ACCESSORIES

CP124 CLUTCH PUMPS AND ACCESSORIES

CP124 with

Bracket Mount, Side SAE O'ring Ports

Page 2: CP124 CLUTCH PUMPS - Permco · Clutch Pump Switch Kit CLUTCH PUMP SERVICE PARTS BR549 Clutch Pump Bracket for 2 Bolt "A" Mount 515376 8 Groove Type K Sepentine Clutch, 90 lb.ft.*

CLUTCH PUMP KIT MODEL NUMBER CONSTRUCTIONCLUTCH PUMP KIT MODEL NUMBER CONSTRUCTION

CP124 P 5 B P R A SClutch Pump/Series

MountingB - SAE 2 Bolt A Bracket Mount (Includes Bracket)P - Pad mountN - SAE 2 Bolt A Without Bracket (Pump Only)

RotationR - Right-hand (Clockwise)L - Left-hand (Counter Clockwise)

GPM @ 1000 RPM, at rated PSI2 - .50 inch gear3 - .75 inch gear5 - 1.00 inch gear6 - 1.25 inch gear7 - 1.50 inch gear9 - 1.75 inch gear10 - 2.00 inch gear

Port TypeP - NPTO - O'ringF - Split Flange (Code 61)

B - Both Side and Rear (1 1/4" NPT Inlet, 3/4 " NPT Pressure Standard)R - Rear Only (1 1/4" NPT or O'ring Inlet, 1" NPT or O'ring Pressure)S - Side Only (1 1/4" NPT, O'ring or Split Flange Inlet, 1" NPT, O'ring or Split Flange Pressure)

Port Location

Clutch

Switch Kit

A - 90* lb. ft. AA Groove6 - 90* lb. ft. 6 Groove K Type Serpentine8 - 90* lb. ft. 8 Groove K Type SerpentineX - No Clutch

S - Switch Kit IncludedX - No Switch Kit Included

* After burnishing, see Owner's Manual

2.00/2.48

1.75/2.17

1.50/1.86

1.25/1.55

1.00/1.24

.75/.93

.50/.62

Gear Width/ Cubic Inch Displ.

GPM(at rated PSI)

20

15

10

5

25

30

0

RPM 20001000 1500 2500 3000

CP124 Performance Chart/Specifi cations

Though the pump and clutch will handle these fl ows and pressures, belt slippage may occur.Maximum inlet vacuum should not exceed 5 IN. HG.

Page 3: CP124 CLUTCH PUMPS - Permco · Clutch Pump Switch Kit CLUTCH PUMP SERVICE PARTS BR549 Clutch Pump Bracket for 2 Bolt "A" Mount 515376 8 Groove Type K Sepentine Clutch, 90 lb.ft.*

2.00/50.80

1.70/43.13

1.16/29.34

Pad Mount Foot Print

7/16 - 14 UNC-28 Thread Thru 2 Places

2.42/61.49

2.00/50.80Optional Side or Rear Only

Port End Cover

2.42/61.49

2.42/61.49

Pad Mount with Dual Ports, AA Groove Clutch

Dimensional Data (inches/mm)

Pad Mount with 6 Groove Serpentine Clutch

Pad Mount with 8 Groove Serpentine Clutch

SAE 2 Bolt A with Bracket, Dual Ports, AA Groove Clutch

SAE 2 Bolt A with Bracket, 6 Groove Serpentine Clutch

SAE 2 Bolt A with Bracket, 8 Groove Serpentine Clutch

Pad Mount Shaft End Cover

4.00/101.60

2.00/50.80

Bracket Mount Foot Print

1/2 Inch Diameter Mounting Holes Thru 4 Places

3.13/79.40

2.28/57.942.81/71.45

2.50/63.50

3/4" NPT Pressure Ports, Side and Rear

Standard

1 1/4" NPT Suction

Ports, Side and Rear Standard

Pad Mount with Dual Ports

3.50/88.90

Port CL

Pulley CL

2.75/69.85

1/4 - 20 UNC-28 Thread Thru 4 Places

1/4 - 20 UNC-28 Thread Thru 4 Places

Bracket Mount

3.50/88.90

Port CL

Pulley CL

2.75/69.85

1.70/43.13

2.28/57.94

2.28/57.94

1.70/43.13 2.75/69.85

2.63/66.68

0.62/15.75

2.42/61.49

4.75/120.65

1.47/37.411.16/29.34

2.42/61.49

2.0/50.80

2.42/61.49

2.35/59.74

6.00/152.40

6.00/152.40

5.47/138.94

Gear Width plus .4/10.16

P - NPT O - O'ring F - Split Flange (Code 61)

Drawings not necessarily to scale. Permco reserves the right to make changes in an ongoing effort to improve the product.

3/8-16 UNC Thread Thru 2 Places

Page 4: CP124 CLUTCH PUMPS - Permco · Clutch Pump Switch Kit CLUTCH PUMP SERVICE PARTS BR549 Clutch Pump Bracket for 2 Bolt "A" Mount 515376 8 Groove Type K Sepentine Clutch, 90 lb.ft.*

Permco Warranty

Permco1500 Frost Rd.P. O. Box 2068Streetsboro, OH USA 44241Phone 330-626-2801Fax 330-626-2805e-mail [email protected]

Permco Hydraulik AGP. O. Box 553

6343 RotkreuzSwitzerland

Phone +41 (0)41 850 86 65Fax +41 (0)41 850 86 67

e-mail [email protected]© Bulletin #CP12404A

Phone 022-25702597, 98, 99Fax 022-25760830

e-mail [email protected]

Permco (Tianjin) Hydraulic Inc. Ltd.#92 Hai Bin Wu Lu, Freezone

Tianjin Port, China

999-00956 Clutch Pump

Switch Kit

CLUTCH PUMP SERVICE PARTSCLUTCH PUMP SERVICE PARTS

BR549 Clutch Pump Bracket for 2 Bolt "A" Mount

515376 8 Groove Type K

Sepentine Clutch, 90 lb.ft.*

520226 6 Groove Type K

Serpentine Clutch, 90 lb.ft.*

512010 AA Groove Clutch,

90 lb.ft.*

Permco WarrantyPermco warrants that its products will not fail due to defects in materials and workmanship. Failure of any product or any one of its components to perform in accordance with design specifi cations, which failure occurs more than (2) two years or 4,000 hours, whichever is less, from the date of shipment of the product from its point of manufacture, shall be presumed to result from deterioration caused by ordinary use. Permco's obligation in the case of defective workmanship or material is limited to replacement or repair of the defective product, or the defective component therein, at Permco's option, in accordance with the procedures explained herein.

$ This warranty is given in lieu of all other warranties, expressed or implied.

$ There are no warranties which extend beyond the description on the face hereof.

When buyer claims a breach of the limited warranty set forth above, the buyer must notify Permco or its agents promptly, whereupon Permco at its option will either examine the product in question at the site, or issue shipping instructions for its return to Permco or one of its authorized warranty repair centers. Transportation cost must be prepaid by buyer on all returns. Credit for freight in and out, based on surface freight rates will be issued if the inspection of the goods shows a defect in materials or workmanship covered by the limited warranty.

* After burnishing, see Owner's Manual