User¡s ManualPlease read this manual carefully before you operate

Mar, 2007 Publish

Network IntelligentAlarm System

1. ------------------------ ------------01----------------2. --------------------------------------------------------013. -------------------------------------------------------024. --------------------- -------------------------------035.Operation Guid --------------------------------------------------------09

What¡s included

Directive 00: Set/modify installer codeDirective 01-09: Set/modify user code/master codeDirective 10-14: Set telephone numberDirective 15-19: Set zone list to dial corresponding telephone number when alarmingDirective 20: Set dialing modeDirective 21: Set telephone communication protocolDirective 22: Set dialing timesDirective 23: Set ringing timesDirective 24: Set ADEMCO accountsDirective 25: Set KS 6+2 accountsDirective 26: Set wireless sirenDirective 27: Open/close phone line cut off report functionDirective 28: Set timing communication zone listDirective 30: Set zone attributeDirective 31: Set respond speed for wired zoneDirective 32: Set circuit type for wired zoneDirective 33: Set Alarm delay/Arm delay for appointed zones.Directive 34: Set inner siren alarm duration for appointed zonesDirective 35: Set linkage alarm duration for appointed zones.

Directive 36: Set the first group of Arm/Disarm timer for zone list

Directive 37: Set the second group of Arm/Disarm timer for zone list

Directive 38: Correct date and time

Directive 41-48: Partition Register

Directive 50: Record

Directive 60: Register/delete remote controllers

Directive 71-78: Register/delete detectors

Directive 80: Come back to default state

6.7.8.9.

e---------------------- ------------------10

------ -------------------------10------------------------------------------12

---12-------------------------------------------------14

------------------------------14-------------------------------------------------14-------------------------------------------------14

-------------------------------------------14---------------------------------------------15

-------------------------------------------------15-------------------------15

--------------------------------15-------------------------------------------------15

-- ----------------------------------16--------------------------------------17

-----------------------17---------------------17

------------------18-----------------19

----------------------- ----------------------19------------------------------------- ---------20

---------------------------- -----------------------------20-----------------------------------21

---------------------- -----------------21------------------------------ -----------23

------------------------------ ----------------25-------- -------------------------------32

--------------------------------------- -----------32------------- --------------------------------33

1. Alarm Console 1PC 2. Remote Controller 2PCS3. Wireless Door Sensor 1PC 4. Wireless PIR Detector 1PC5. Double-end phone cable 1PC 6. Plastic Antenna 1PC7. 2.2K resistance 4PCS 8. Power Cable 1PC9. User s Manual 1PC¡

------------- ---------------------------------34------------- ----------------------------------38

Table Of Contents

Main FunctionsSystem Instruction

System DiagramSystem Installation

User¡s Operation GuideMain Technical SpecificationOperate PrecautionsFrequently Ask Questions

10. Wireless PIR Detector11. Wireless Door Sensor

-----------------------18

1.System IntroductionThis system is Telephone Networking Alarm Console with 12 zones (8 wireless zones and 4 wiredzones). It can work with remote controllers (up to 8 remote controllers), various wireless (wired)sensors and wireless (wired) siren. It can be stored 5 groups of pre-set telephone numbers(fixed/mobile telephone number and pager number). Once an alarm happens, the alarm console willactivate on-site siren immediately; and dial pre-set telephone number at the same time. It is widelyused in residence, marketplace, finance system and enterprise.

2. Main Functions:2.1 It is easy to operate with 4*4 keyboard and lattice LCD display.2.2 Voice pre-recorded. It guides to operate by sound and correctly reports alarm information

when alarm occurs.2.3 There are 4 wired zones and 8 wireless zones altogether, and they share with the zone number.2.4 8 sub zones can be programmed independently. And the zone list can be set freely in each sub

zone, 8 remote controllers and 8 user's codes can separately program 8 sub zones toARM/DISARM independently.

2.5 Code classification, 1 installer code, 1 master code, and 8 common users¡ codes. Add 1 at theend of master code/ common user's code, and then it will become duress code.

2.6 Support to ADEMCO CONTACT ID communication protocol2.7 5 groups of telephone numbers (mobile and pager number) can be set. Dialing type (tone or

pulse) and appointed communication zone can be programmed. Arm/Disarm, whether to reportthe information of system state can be set freely.

2.8 DTMF (double-tone multi frequency) and pulse dialing mode are available.2.9 It rushes to report alarm information when alarming (the line should be correctly onnected).2.10 Telephone line cut off or short-circuit will send an alarm. (Indicate sound or siren are

optional, this function also can be opened/closed).2.11 Dial the telephone number, which connected with main unit to arm/disarm and start alarm on

the spot function remotely through telephone or mobile phone.2.12 Automatically learn code between wireless PIR detector, remote controller and main unit

01.

3. System Diagram

Alarm Console

Monitor CenterTelephone Mobile

Wireless PIR Sensor

Wireless Door Sensor

Wireless Smoke Sensor

Emergency Button Remote Controller Wired Siren

Wired Gas Sensor

Wired Door Sensor

Wired PIR Sensor

Wired Smoke SensorOn-site Monitor

Wireless Gas Sensor

Wireless Siren

On-site Monitor

02.

each zone can be learned 3 detectors, so 4 detectors and 8 remote controllers can be learned altogether2.13 Wired zone respond speed is 0ms-750ms, and the circuit types (Normal Open, Normal Close and

Close and line-end resistance) can be set freely to connect with all kinds of wired detector2.14 Two timers can be set to Arm/Disarm different zones independently.2.15 Alarm delay time (00-99 seconds) and Arm delay time (00-99 seconds) can be set for appointed zones2.16 It has completed self-check function, Main unit/detector disassembly, AC power cut, backup battery

lower of main unit or detector will activate alarming.2.17 Linkage with wired/wireless Siren2.18 Latest 20 pieces of alarm record (Alarm information, Month/Day/hour/minute) can be recorded, and

the user and time of the last arm time and the last disarm time can be recorded. If the records are over20 pieces, then it will delete the preceding ones automatically. User cannot change/delete the records

2.19 Main unit and wireless PIR detector make communication in 26 hours to check if there arecommunication malfunctions. If there are malfunctions, the main unit will alert corresponding zonewithin 26 hours. (This function can be opened/closed)

2.20 Wireless detector reports to main unit for on/off. The report will be kept in record.2.21 Both AC220V and 12V/1.3Ah rechargeable battery supply power, usually, it charges the backup

battery automatically, and they switch automatically. The backup battery can work for 24 hours ormore in standby time. And it reports when power lower. To avoid battery damaged, It adopts limitedcurrent discharge protection circuit.

25

4.04.03.

System Installation

(1) Firstly, make a scheme of all defense zones according to user¡s needs, and choose suitable kindsof detectors.

(2) Fix the setup places of all fittings, like alarm host ,detectors and sirens.(3) Draw a setup map marking the types and specification of detectors and cable conductors in all

zones, and marking the different usages of all kinds of color lines. Don¡t use the same color cablesin different zones of the same system.(The scheme and the map should be filed for maintenance afterwards)

Considering the factors as following when making defense scheme and drawing the map.*After making sure the credibility of detector, it should be fixed in hide places, and the alarm hostshould be fixed in a place where is easy to reach but not easy to be found, and there should havesockets nearby, it also should be near to telephone line and within defense zone of detector. Sirenor trumpet should be set in the best place. Emergency button should be set in the most convenienceplace.

*There should be no big mental or other electrical applicants which can produce interferes (liketelevision, air-condition,computer and micro-oven and so on) near to the install place of alarmhost and other wireless communication equipments.

*When installing wired detector, the cable should be fixed in hide place, like line groove in ceiling.Don¡t use the same color cables in the different zones of the same system.

*Considering all factors, which could cause interferes when adopting wireless detectors and wirelesssiren. Usually, in open area, the distance between the above detector, siren and alarm host can reachto 400m. The alarm host should be set indoors. Otherwise, in the course of transmitting, wirelesssignal may be absorbed or weaken by all equipment material indoors. Moreover, other signals ofwireless equipment may make interferes to this transmit signal. Therefore, the transmitting distanceIs less than 400m when used indoors.

Note:

1. Take main unit and all accessories out of packing box, power them on or well install battery,then program main unit as the need indeed, and learn the code of PIR detector, door sensorand remote controller to main unit (the code of all accessories in the standard package hasbeen learned), please refer to the corresponding chapter for specific operations.

2. How To Install Main Unit(1) How to open the up cover* Put a ¡-¡ screwdriver on the place as picture (a), and unclench upward lightly, then the up

cover will separate with the base cover.* Lightly up lift the up cover to about 15 degrees by hand as picture (b). (Note: Don¡t up lift too

high because it is easy to damage the hook).* Lightly swing the up cover right and left as picture (c). (Note: Don¡t swing with strong

strength), then the up cover will be opened.* disconnect the line which connect the up cover with the base cover.

4.1 Install Preparation

4.2 Start To Install Picture 1

( )a

Press down

Clench up

(b)

Uplift about 15¡

04. 06.05.

The above picture is the inner structure of main unit(2) How to mount main unit on the wall* Demount up cover, and there are two install holes on the both end of cover (up and

down side). Hammer two nails on the wall where main unit you want to install, and thenmount the up side of main unit on the up side nail. (Note: the nail which mounting the mainunit should be fastened and can bear three times of weight of main unit at least.)

* Put all lines (like wired detector, telephone line, wired siren) through the hole in the middlecover, and then correctly connect all wired lines with the wired interfaces. (Refer to thecorresponding chapter for specific operation).

* Put all lines in order, then mounts the down sides of lain unit on the down side nail, andFirmly fix it, then return up cover and firmly fix it. (Note: the cover should not bedisfigured).

(3) How to connect with wired accessories1).This system provide with wired interfaces, so it is very convenience to connect with wired

accessories.A. Zone Loop (Z9 to Z12 terminal): Zx terminal is anode, and C terminal is cathode (earth

terminal). When connecting with hand-pressing switch or foot-triggering switch, it is notneed to distinguish the polarity.

B. Auxiliary Power Terminal (AUX&C terminal): It provides wired accessories whichrequire power with +12V DC.

C. Linkage Output Terminal (NC/NO terminal): They are used to control on-off of otherequipments. NC is normal close, NO is normal open, and COM is common terminal. Itcan load with 1A120V AC/24V DC. If the power of controlled equipment is exceedingthan that, it is recommended to use a relay with larger power to avoid damagingthe controlled main board.

2).You should install following instruction when installing other wired equipments.mark the different usage of all kinds of color lines, then install as the drawing, andlead the lines to main unit, and then correctly connect with main unit. And theconnection are as following:

A. Different color line have different usage, so when connecting, the line should bestrictly according to the different uses of different color lines.

B. When connecting, the line end should be bared, and the length of bared should beequal to the connect port where will be inserted. Then the bared line should betwisted firmly, then insert them into the hole, after that, screw the screw cap firmly tobear pulling strength.

C. There are three kinds of circuit can be programmed, that are ¡normal close¡, ¡normalopen¡ ¡ line end resistance¡. If it is programmed to be ¡ line end resistance¡, youshould connect a 2.2 K resistance with the end terminal of PIR detector (other zonecircuits unused for the moment also should be connected). In order to avoid zonecircuit lines damaged (be cut off or short circuit), you had better programcorresponding zone circuit to be ¡line end resistance¡.

is bypass connect with out lines, it should be weld after connection. Moreover, thepart of resistance down-lead should be as short as possible to avoid short circuit bytouching with other metals after twisted. If the zone loop are programmed to be NOor NO, then the detector can be connect directly with the zone loop. When detectorneed main unit to provide power, the anode and cathode of the detector¡s power inputinterface should be separately connected with SW and C interfaces or AUX and Cinterfaces.

Ω

Connection Principles:Normal open detector should be connected parallel with normalclose detector should be concatenated with If more than two linesshould be connected with the same end, then the bared line should be twisted firmly,then insert them into the hole and screw the screw cap firmly. If resistance down-lead

For example: Z9 and Z12 are programmed to be the type of ¡line end resistance¡,Z10 is programmed to be the type of ¡ NO¡, Z11 is programmed to be the type of ¡NC¡,

2.2 K resistance;2.2 K resistance.

ΩΩ

Picture 1

(c)

(a)

Picture 5

BuckleBuckle

07. 08.and Z9, Z10 and Z11 is required to separately connect with one KS-300DLT (wired PIR sensor,o e a

b

ne mergency button and one switch. Then you can refer to picture 3 ( ) for specificconnection. If several devices to be connected in one zone loop, then parallel connection, seriesconnection or series-parallel connection as picture 3 ( ) can be adopted.

D. It only can be connected with wired siren which is active, and the connection is like picture 3 (c)

PIR Sensor Emergency Button Magnet Switch N/C, N/O mixed connection Wired Siren

N/O connection

N/C connection

Sensor 1 Sensor 2 Sensor 3

Sensor 1 Sensor 2 Sensor 3

Sensor 1Sensor 2 Sensor 3

Lead

Phone line Socket

Picture 4(6) How to connect with backup battery

short-circuit backup battery is not allowed in any situation, andNote:

s please

* Connect the black line with the cathode of backup battery.* Put the backup battery into the case* Connect the red line with the anode of backup battery.

wrong pecification and wrong connection of battery my cause explosion, soInstall the battery as instruction.

* Remove the double face glue on the case of backup battery.

(7) How to connect with powerHow to close up cover

* Aim at the both buckles of the up cover and base cover as picture (a), then close firmlyboth of the cover as picture (b).

* Power main unit on.Note: When power on, the system is in Disarm state, Date and Time are shown 1-01¡ ¡

¡12:00¡, please correct them to be the same as the present time.

Picture 3

(4) How to connect with antenna.Insert the plastic antenna into the hole at the right-top side of main unit,And screw it firmly on PCB board.

(5)How to connect with phone line*The outside line of PSTN should be inserted to IN position.(Note: the outside line should not be connected with otherequipments. and it should be connected, then it will dial the trephinenumber you had set when Alarming.*The line for phone machine is inserted to OUT position.

▲

(See diagram4 )

(See diagram 4)

(b)

Close firmly

5.2Program InstructionHow to enter program state:

picture 6

picture 7

When main unit is in isarm state, Press key, main unit will indicate with PleaseEnter Code . display will show as You are allowed to enter Installer Code orMaster Code. Bi Bi two Bi means the operation is correct and main unit will enterprogram state. display will show as . If the code you entered is incorrect, themain unit will indicate with The code is incorrect, please re-enter . display will showas picture 6 If incorrect code is entered for three times continuously, the main unit will alarmon the spot and keyboard will be locked for one minute automatically.

d ϖSETϘ ¡¡ LED .

¡ ¡ ¡¡

LED¡ ¡ LED

.

Picture 6 Picture 7

c

4. . Debugging3Further test system, test to see whether all accessories you installed can work normally orNot. Whether they can communicate normally with main unit, and whether main unit canMake alarm sound normally.

This system can be programmed freely according to user¡s needs, therefore, please carefullyread this User¡s Manual before operation to fully perform all its functions.

Then the installation is finished.

5. Operation Guide

5.1Program

[

[

1) Program Mode

SET] + [CODE] + [OK] +[ Program Directive] + [OK] +[ Directive Index] + [ OK] + [Reset]

Note: SET] + [CODE] + [OK] is used for system to enter program state.[SET] + [Installer¡s code] + [OK] is used to enter installer program state;[SET] + [Master¡s code] + [OK] is used to enter master program state.

2) The system can enter program state only in disarm state and without any alarm occurs(including power lower supply).

3) In program state, main unit can¡t receive any alarm signal.4) Press Reset key to delete the latest i nputs. Repeatly press Reset key to come back to the

last menu.5) No program operations for 60 seconds in program state, the system will exit automatically.6) Press Reset to scroll wanted program, or press corresponding program indicative directly.7) In program state, the system can be programmed continuously.8) In program state, if you desire to change Program Directive to the other one, you should

press reset key to change directive.

Directive 00δ:Set/modify installer code

In installer program state, Press 00 + OK . LED display will show s picture .Enter new code 6 digit + new code 6 digit + OK ]. BiBi two Bi means theoperation is correct. The LED display will show as picture .Press Reset key for moreprogram.For instance, you want to change installer code to be 123456. Press 00 + OK +123456 + 123456 + OK

Installer code is 000000 by default

In installer program statePress [01] + [OK] + [User¡s code 4 digits] + [ User¡s code 4 digits] + [OK] to set the 1st user¡s

codePress [02] + [OK] + [User¡s code 4 digits] + [ User¡s code 4 digits] + [OK] to set the 2nd user¡s

code

［ ］ ［ ］ a

［ ］ ［ ］ ［ ¡ ¡

［ ］ ［ ］ ［

］ ［ ］ ［ ］

8

9

Directive 01-09: Set/modify user code/master code

Picture 8 Picture 9

C000000 00

C 0012 3456

09. 10.

Directive 10-14: Set telephone number

In installer program state

Note:

No stored phone number by default

Press 10 + OK + Phone No. + OK to set the 1 stored phone number

Press 11 + OK + Phone No. + OK to set the 2 stored phone number

Press 12 + OK + Phone No. + OK to set the 3 stored phone number

Press 13 + OK + Phone No. + OK to set the 4 stored phone number

Press 14 + OK + Phone No. + OK to set the 5 stored phone number

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

st

nd

rd

th

th

1. Press one * to dial delay for 3 seconds. It is used for extension number and semi-pagerstation. For instance, stored phone number 2532182*804. It means dialing 2532182 firstly,and stop for 3 seconds, then dial 804.

2. Press # to delete the corresponding stored number. for instance, to delete the second phonenumber. Only press 11 + OK + # + OK

3. Each stored phone (including *) is not beyond 20 digits.4. For wrong stored phone number can be re-enter directly. Or delete the wrong number, and

then enter the right one.to set the second phone number 2532182, extension number is 804.

In installer program statePress 11 + OK + 2532182*804 + OKLED display will show as picture 11

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

For instance,

Directive 15-19: Set(

zone list to dial corresponding telephone number whenalarming Arm/Disarm/self inspect report)

In installer program statePress 15 + OK + appointed zone No. + OK to set appointed zones to dial the1 stored phone number.

［ ］ ［ ］ ［ ］ ［ ］st

Press [03] + [OK] + [User¡s code 4 digits] + [ User¡s code 4 digits] + [OK] to set the 3rd user¡sCode

Press [04] + [OK] + [User¡s code 4 digits] + [ User¡s code 4 digits] + [OK] to set the 4th user¡sCode

Press [05] + [OK] + [User¡s code 4 digits] + [ User¡s code 4 digits] + [OK] to set the 5th user¡sCode

Press [06] + [OK] + [User¡s code 4 digits] + [ User¡s code 4 digits] + [OK] to set the 6th user¡sCode

Press [07] + [OK] + [User¡s code 4 digits] + [ User¡s code 4 digits] + [OK] to set the 7th user¡sCode

Press [08] + [OK] + [User¡s code 4 digits] + [ User¡s code 4 digits] + [OK] to set the 8th user¡sCode

Press [09] + [OK] + [User¡s code 4 digits] + [ User¡s code 4 digits] + [OK] to set the 9th user¡sCode

For instance, set the second group of user¡s code to be 5678, then you can operate asfollowing:Enter installer or user¡s program state;Press [02] + [OK] + [5678] + [5678] + [OK], the LED display will show as picture 10.

Note: 1. Different user¡ s code can not set to be the same, and it can not be the same as otherduress code.

2. If you want to delete some user¡s code, just enter a ¡#¡,For example: if you want to delete the 8th user¡s code, you can enter like this:[08] + [OK] + [#] + [OK].

Master code only can be modified, and it can not be deleted.3. 1-8 user's codes and 1-8 remote controllers are defined to be 1-8 users,

and different users can operate corresponding zone independently.Master code is 1234 by default, and there are no any user¡s code by default.

5678C02

Picture 10

C 1125 32 1 82* 80 4 Picture 11

11. 12.

Directive 21: Set telephone communication protocol

Press [16] + [OK] + [appointed zone No.] + [OK] to set appointed zones to dial the 2nd storedphone number.

Press [18] + [OK] + [appointed zone No.] + [OK] to set appointed zones to dial the 4th storedphone number.Press [19] + [OK] + [appointed zone No.] + [OK] to set appointed zones to dial the 5th storedphone number.Note:1. It can set to dial appointed telephone number when arm/disarm/self-inspection, and

The code of arm/disarm is 13, the code of self-inspection is 14 ( self-inspectionincludes power lower of main unit/detector and AC power cut off).

2. If the zone number is 10,11, 12, Arm/Disarm code is 13, self inspection code is14, youshould press SET 0 , SET 1 , SET 2 , SET 3 , SET 4 , and The LEDdisplay will show A, B, C, D, E.

Example 1 you want to set zone 1, 3, 5, 7, 9, 11, 12 to dial the first stored phone number whenthey occur alarm.In installer programPress 15 + OK + 1, 3, 5, 7, 9, SET 1, SET 2 + OKLED display will show as picture 12

Example 2 you want to set zone 2, 4, 6, 8, to dial the second stored phone number when theyoccur alarm.In installer program statePress 16 + OK + 2,4,6,8 + OKLED display will show as picture 13

［ ］ ［ ］ ［ ］［ ］［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

,

,

Press [17] + [OK] + [appointed zone No.] + [OK] to set appointed zones to dial the 3rd storedphone number.

C 151 35 79 BC

Picture 12

C 1 62 4 6 8 DE

Picture 13

Directive 20:Set dialing modeIn installer program state, Press 20 + OK + 0 or 1 + OK , 0 for tone, 1 for pulse.Tone be set by default

In installer program state,21 + OK + x x x x x + OK , x= (0, 1), 0 for audio alarm, 1 for CONTACT ID

protocol alarm. x x x x x is protocols for 5 stored phone number.For instance, the first and second stored number for CONTACT ID protocol alarm, the third,forth and fifth stored number for audio alarm.In installer program state

21 + OK + 1 1 0 0 0 + OKLED display will show as picture 14

All stored phone number will be audio alarm by default

In installer program statePress [22] + [OK] + [X] + [OK], X= 1-95 times by default

In installer program statePress [23] + [OK] + [XX] + [OK], X= 05-15

Main unit receives a remote call when the ringing times arrives, main unit willresponse automatically, then you can enter directives.8 times by default

In installer program statePress [24] + [OK] + [Account 4 digits] + [OK]

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

Directive 22: Set dialing times

Directive 23: Set ringing times

Note:

Directive 24: Set ADEMCO accounts

C21110 00

Picture 14

13. 14.

Directive 27: Open/Close phone line cut off report function

Directive 30: Set zone attribute

Directive 28: Set timing communication zone list

set and there are no user¡s accounts by default

In installer program state, press [25] + [OK] + [Accounts 6 digits] +[OK]

In installer program state, press [26] + [OK] + [Address code 8 digits] + [OK]8 digits address code is labeled at the back of wireless siren.If you want to delete wireless siren, press [26] + [OK] + [#] + [OK]There are no address code by defaultFor instance, you want to set a wireless siren. Code is A7DF.In install program, press 26 + OK + SET0 7 SET3 SET5 + OKLED display will show as picture 15

Note: when networking with manage center, user¡s account (6 digits) should be set. (Thisfunction is not start at present). And there are no user¡s accounts by default.

In installer program state, press 28 + OK + zones 1-8 + OKFor instance, you want to set 1, 2, 3, 4 zone to send a timing report to the main unit. Ininstaller program state, press 28 + OK + 1, 2, 3, 4 + OKPress 28 + OK + # + OK to delete timing communication zone listNo timing communication zone list by default

In installer program state, press 30 + OK + xxxxxxxxxxxx + OK , x is zoneattribute of each zone. 12 x is for 12 zones, X value scale see attribute table below:

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

In installer program state, press 27 + OK + 0 or 1 + OK . 0 for close report, 1 foropen report.Open report by default

［ ］ ［ ］ ［ ］ ［ ］

.

Attribute table

Code Zone Attribute

0 By pass1 Fire Alarm2 Gas Alarm3 Emergency Alarm4 Medical Alarm5 Intrusion Alarm6 Perimeter7 Door-bell

Directive 31: Set wired zonerespond speed for

Code Wired zone respond speed1 50ms

2 (default) 100ms3 250ms4 500ms5 750ms

Directive 25: Set KS 6+2 accounts

Directive 26: Set wireless siren

C 26A7DF

Picture 15

2. Fire alarm, Gas alarm, emergency alarm and medical alarm are treated as 24 hoursper day. It is out of control by Arm/Disarm.

3. Vacant zone or unused zone can be bypassed.4. The number of zone attribute should be 12 digits5. If zones are set to be doorbell zone is attribute, it is only for door alert, and there are

no alarm and it also can¡t dial stored phone No.All zone attributes are set to be intrusion alarm by default.

In installer program state, Press 31 + OK + xxxx + OK . X is zone speed forZones from 9 to 12. X value table below

［ ］ ［ ］ ［ ］ ［ ］

100ms for all wired zones by default

15. 16.

Code Wired zone type1 Normal Open2 Normal Close3 End of line Resistance

Directive 33: Set Alarm delay/Arm delay for appointed zones.

Zones] +[ OK]Siren duration range: 03-99 minutes (2 digits)Zone number range: 1,2,3,12,13 (13 is for phone line cut off alarm).Note: If the number is 10, 11, 12. or 13, you can enter SET 0 , SET 1 SET 2 orSET 3] for corresponding 10, 11, 12. or 13 . A B C D will show on screen for correspondingnumberFor instance, If you desire to set zone 2 4 6 8 10 11 and phone line cut off, siren duration is 30minutes when it alarms, In installer program state, press 34 + OK + 30 2 4 6 8SET0 SET3 + OKThe screen display will show as picture 17

［ ］ ［ ］［ ］ ［

［ ］ ［ ］ ［ ］［］ ［ ］SET1

Siren duration is 20 minutes for all zones and there are no siren for phone line cut off by defaultEmergency alarm and anti-tamper alarm are unlimited by siren duration time.Note:

Directive 35: Set linkage alarm duration for appointed zones.

In installer program state, press 35 + OK + linkage alarm duration] appointedzones. + OKLinkage alarm duration range: 03-99 minutes (2 digit)Zone number range : 1, 2,3, 12 , 13. (13 is for phone line cut off alarm)

If the number is 10, 11, 12. or 13, you can enter SET 0 , SET 1 SET 2 orSET 3 correspondingly . A B C D will show on screen for corresponding number.For instance, If you desire to set linkage alarm duration for 30 minutes when zone 2 4 6 8 10 11occurs alarm or phone line cut off. In installer program state, press 35 + OK + 302 4 6 8 SET0 SET1 + OK], as picture 18.

［ ］ ［ ］ ［ ［］ ［ ］

［ ］ ［ ］［ ］ ［］

［ ］ ［ ］ ［ ］［］ ［

Note:

SET3 The screen display will show

Siren duration is 20 minutes for all zones and there are no siren for phone line cut off by defaultEmergency alarm and anti-tamper alarm are unlimited by siren duration time.Note:

Directive 36: Set the first group of Arm/Disarm timer for zone list

In installer or master program state, press 36 + OK + Arm time Disarm timepartition No. + OK

［ ］ ［ ］ ［ ］［ ］［］ ［ ］

Directive 32: Set circuit type for wired zone

Note:

Directive 34: Set inner siren duration for appointed zones

In install program state, press 32 + OK + xxxx + OK , X is wired zoned typefor zone 9 to 12.X value see table below:

If you select zone type of end of line resistance, for N/O (Normal Open) device, youhave to parallel connect with a 2.2k resistance. For N/C (Normal Close), you have to seriesconnect with a 2.2k resistance. (end of line resistance type is recommended for all zones.)End of line resistance type for all zones by default.

In installer program state, press 33 + OK + Alarm delay time Arm delay timeappointed zones + OK

Alarm delay time range: 00-99 seconds (2 digits)Arm delay time range: 00-99 seconds (2 digits)Zone number range: 1, 2,3, 12Note: If the number is 10, 11, 12, you can enter SET 0 , SET 1 SET 2correspondingly . A B C will show on screen for corresponding number.For instance, if you desire to set zone1 3 5 7 10 12 for alarm delay and arm delay, alarm delaytime is 30 seconds; arm delay time is 50 secondsIn installer program state, press 33 + OK + 30 50 1 3 5 7 SET0 SET12 +OK . The screen will show as picture 16:

No alarm delay time and arm delay time by default

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］［ ］［ ］ ［ ］

、、、

［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］［ ］［ ］ ［

］

In installer program state, press 34 + OK + inner siren duration appointed［ ］ ［ ］ ［ ］［

C 3 33 0 5 0 1 35 7A C Picture 16

C3430246AB D Picture 17

C353 0246 ABD Picture 18

17. 18.

Arm time range is 4 digits, 2 digits for hour, 2 digits for minutesDisarm time range is 4 digits, 2 digits for hour, 2 digits for minutesPartition number range is 1 2 9. (9 is for all partitions)For instance, if you desire to arm at 08:00pm, and disarm at 18:00pm for all partitionsautomatically. In installer program state, press 36 + OK + 0800 1800 9 +OK . The screen display will show as picture 19

¡¡

［ ］ ［ ］ ［ ］［ ］［ ］ ［

］

Press 36 + OK + #. + Ok to delete the first group of timer for arm/disarm andpartitions.

In installer or master program state, press 37 + OK + Arm time Disarm timepartition No. + OKArm time range is 4 digits, 2 digits for hour, 2 digits for minutesDisarm time range is 4 digits, 2 digits for hour, 2 digits for minutesPartition number range 1 2 9. (9 is for all partitions)For instance, if you desire to arm at 16:20pm, and disarm at 07:40am next morning for partition1, 2 automatically. In installer program state, press 37 + OK + 1820 0740 12 + OK .The screen display will show as picture 20

Press 37 + OK + #. + OK to delete the second group of timer for arm/disarm andpartitions.No timer for Arm/Disarm by default

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］［ ］［

］ ［ ］

¡¡

［ ］ ［ ］ ［ ］［ ］［

］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

Directive 37: Set the second group of Arm/Disarm for zone list

Directive 38: Correct date and timeIn installer or master program state, press 38 + OK + month date hourϖ Ϙ ϖ Ϙ ϖ Ϙϖ Ϙϖ Ϙ

Month, date, hour and minutes are should be 2 digits separately.

In installer program state,

Zone number range is 1, 2, 3, 121.If you want to enter zone number 10, 11, 12, you can enter SET 0 , SET 1

SET2] correspondingly. A B C will show on screen for corresponding number.2. Each zone can be registered repeatedly in different partitions.3. If you want to delete the zone list of some partition, then you should press ¡#¡ .

For example: to delete the zone list in the 8th partition, then you can press as below:[48] + [OK] +[#] + [OK] to delete the zone list in the 8th partition.

4. 1 and different

For instance, you appointed zone 1, 3, 5, 7, 11, 12 registered in first partition. Ininstaller program, press 41 + OK + 1, 3, 5, 7, SET1, SET2 + OK for the1 st partition. The screen display will show as picture 21.

In installer program state, press 50 + OK to enter the record menu. And press 0 +OK to start recording for 10 seconds. Aim at microphone to record and Press OK tofinish. Press 1 + OK to display record.

Directive 41-48: Partition Register

Directive 50: Record

Press 41 + OK + appointed zone No. + OK for the 1 partitionPress 42 + OK + appointed zone No. + OK for the 2 partitionpress 43 + OK + appointed zone No. + OK for the 3 partitionpress 44 + OK + appointed zone No. + OK for the 4 partitionpress 45 + OK + appointed zone No. + OK for the 5 partitionpress 46 + OK + appointed zone No. + OK for the 6 partitionpress 47 + OK + appointed zone No. + OK for the 7 partitionpress 48 + OK + appointed zone no. + OK for 8 partition

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

st

nd

rd

th

th

th

th

th

¡¡

［ ］［ ］［

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［

］ ［ ］

［ ］ ［ ］

Note:

-8 user's codes and 1-8 remote controllers are defined to be 1-8 users,users can operate corresponding zone independently.

C3608001800 9 Picture 19

C3 718 20 07 40 12

Picture 20 C 4 113 57 BC Picture 21

19. 20.

Directive 60: Register/delete remote controllers

Directive 71-78: Register/delete detectors

In installer program state, press 60 + OK enter remote controller register menu. Andenter code number from 1 to 8 for corresponding remote controller and OK key toconfirm.In register menu.

1 + OK to register the 1 remote controller2 + OK to register the 2 remote controller

up to 8 remote controllers altogetherIf the zone is vacant, the screen will show as Picture 22 , if code has been registered in thiszone, the screen will show as picture 23.Register one remote controller in vacant , press Arm key on remote controller, Bi-Bi- isindica for register successfully. If code h been registered , there is aDi indicat for alert and the screen show as 23in that menu, press # + OK to delete the original register firstly, then register it the sameas vacant code.Press 1 + OK + # + OK to delete the 1 remote controllerPress 2 + OK + # + OK to delete the 2 remote controller

..up to 8 remote controllersIn installer program state,press 69 + OK + # + Ok to delete all registered remote controllers.

Note:1. After learning the code, test again is recommended.2.1 and different

In installer program state,Press 71 + OK to enter the 1 register zone.Press 1 + OK to register the 1 sensor

［ ］ ［ ］［ ］

［ ］ ［ ］

［ ］ ［ ］

¡¡

¡

［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

¡

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］

［ ］ ［ ］

st

nd

st

nd

st

st

zonete other as in this zone long

sound e ing will picture .

-8 user's codes and 1-8 remote controllers are defined to be 1-8 users,users can operate corresponding zone independently.

Press 2 + OK to register the 2 sensorPress 3 + OK to register the 3 sensorPress 72 + OK to enter the 2 register zone.Press 1 + OK to register the 1 sensorPress 2 + OK to register the 2 sensorPress 3 + OK to register the 3 sensor

［ ］ ［ ］

［ ］ ［ ］

［ ］ ［ ］

［ ］ ［ ］

［ ］ ［ ］

［ ］ ［ ］

nd

rd

nd

st

nd

rd

¡¡

［ ］ ［ ］

［ ］ ［ ］

［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

［ ］ ［ ］ ［ ］ ［ ］

up to 8 register zonesFor instance, register the third sensor in the second register zone.In installer program state,Press 72 + OK to enter the second register zone.Press 3 + OK to register the third code.

for vacant co , for registered code.

Register one sensor in a vacant code, trigger sensor to send a signal to main unit, Bi-Bi- is forsuccessfully register.If code has been registered, and you want to register other one in this zone, then you have todelete the old one firstly. press # + OK to delete, then register the new one the same asvacant code.In installer program state,press 79 + OK + # + OK to delete all registered sensors.Press 71 + OK + to enter the 1 register zone.Press 1 + OK + # + OK to delete the 1 sensorPress 2 + OK + # + OK to delete the 2 sensorPress 3 + OK + # + OK to delete the 3 sensorPress 72 + OK to enter the 2 register zone.Press 1 + OK + # + OK to delete the 1 sensorPress 2 + OK + # + OK to delete the 2 sensorPress 3 + OK + # + OK to delete the 3 sensor

Picture 24 de picture 25

st

st

nd

rd

nd

st

nd

rd

C6 0--- -- - AC 9 0 A B

C 6 0Picture 22 Picture 23

C 7 2- - - - - - 1 3 57 B C

C7 2

Picture 24 Picture 25

21. 22.

Note: 1. There are many ways to register detectors: such as trigger PIR, trigger anti-tamper, orturn on/off power switch.

2. Test is recommended after registering.

In installer program statePress 80 + OK + # + OK], main unit will come back to default state.

The directives Marked with in remark column can be programmed by master code and usercode. Others only can be programmed by installer code.

［ ］ ［ ］ ［ ］ ［

5.3 Program Table

Directive 80: Come back to default state.

Program Definition Default Users RemarkDirective memo0001020304050607080910

Modify installer code

Set/delete the 1 user codest

Set/delete the 2 user codest

Set/delete the 3 user codest

Set/delete the 4 user codest

Set/delete the 5 user codest

Set/delete the 6 user codest

Set/delete the 7 user codest

Set/delete the 8 user codest

Modify master code

000000NoNoNoNoNoNoNoNo

1234

111213141516

Set/delete the 1 stored phone numberst NoNoNoNoNo

Set/delete the 2 stored phone numberst

Set/delete the 3 stored phone numberst

Set/delete the 4 stored phone numberst

Set/delete the 5 stored phone numberst

Set/delete 1 stored phone number for appointed zonesst 123456789ABC

123456789ABCSet/delete 2 stored phone number for appointed zonesst

18192021

123456789ABCSet/delete 4 stored phone number for appointed zonesst

Set/delete 5 stored phone number for appointed zonesst 123456789ABC

22232425262728303132333435363738414243

Set dialing mode 0(DTMF)Set telephone communication protocol 00000Set dialing times 5Set ringing times 08Set ADEMCO accounts No

NoNo

Set KS 6+2 accountsSet wireless sirenOpen/close phone line cut off report 1(open)

Set timing communication zone list NoSet zone attribute 555555555555

Set wired zone response speed 2222Set circuit type for wired zones 1111Set alarm delay/Arm delay for appointed zones

Set inner siren duration for appointed zone

Set linkage alarm output for appointed zones

Set 1st timer for Arm/Disarm

Set 2nd timer for Arm/Disarm

Correct Date and Time

No20123456789ABC

20123456789ABC

NoNo

Set/delete the 1 partition for appointed zonesst

Set/delete the 2 partition for appointed zonesst

Set/delete the 3 partition for appointed zonesst

123456789ACD

123456789ACD

123456789ACD

17 123456789ABCSet/delete 3 stored phone number for appointed zonesst

Program Definition Default Users RemarkDirective memo

44 Set/delete the 4 partition for appointed zonesst 123456789ACD

23. 24.

Program Definition Default Users RemarkDirective memo45 Set/delete the 5 partition for appointed zonesst 123456789ACD

46 Set/delete the 6 partition for appointed zonesst 123456789ACD

47 Set/delete the 7 partition for appointed zonesst 123456789ACD

48 Set/delete the 8 partition for appointed zonesst 123456789ACD

50606971727374757677787980

Record NoRegister/delete remote controllersDelete all register remote controllersRegister/delete sensor in the 1st zoneRegister/delete sensor in the 2nd zoneRegister/delete sensor in the 3rd zoneRegister/delete sensor in the 4th zoneRegister/delete sensor in the 5th zoneRegister/delete sensor in the 6th zoneRegister/delete sensor in the 7th zoneRegister/delete sensor in the 8th zoneDelete all registered sensors

Come back to default state

NoNoNo

No

NoNo

NoNo

6.Users¡ Operation Guide6.1Panel Instruction1). LED indicator

1 to 8 zone indicators are for wireless zones. 9 to 12 zone indicators are for wired zones.All the zone indicators are off in normal state.The zone indicator is on when it detects alarm signalThe zone indicator will be flashing once every 4-second when it is armed.

2). LCD display

Two lines for LCD display, up-line is for time and 3 characters, down-line is for 11 charactersdisplay. After powered on and self-inspect, LCD display is initialization state (see picture 26)

K S - 8 9 8 A

Read alarm information on screen when system occurs alarm. For instance, a fire alarm occursin the 8th zone (see picture 27 ).

Z 0 8 F i r eN 0 1

Alarm time September 15th , 11:38. N01 means the first alarm record. Z08 meansthe 8th zone, Fire means fire alarm. The screen can be scrolled for more alarm records,

¡ ¡ ¡ ¡ ¡

Po wer i nd i ca tor ( in red ) :

RUN indicator (in red):

Arm indicator (in red):

Emergency indicator (in red):

Powerindicator is on in red for AC supply innormal. Power indicator is off for ACsupply cut-off.

The indicator ison in red one second when power is on.And flashes once every 4 seconds.

The indicator ison when main unit accept arm order.Otherwise, it is off when main unit acceptdisarm order.

It is onwhen emergency alarm occurs by pressingemergency key on remote controller. It isoff when system is disarmed.

LCD Display

MicrophoneLED Indicator

Keyboard

Inner Siren

Alarm Panel

ARM

SET

OK

RESET

Network Intelligent Alarm System

Z one lnd icator

PMR RUN ARM EMC

101 12 : 00We lcome

1,2 has been learned

Picture 26

Picture 27

25. 26.

3). Remote controller

is Arm keyis Disarm keys emergency key, on-site alarm will be

activated and it will dial stored phone numberswhen pressing emergency key.

i

Antenna5 seconds)Indicator

Arm

Disarm

Emergency

Remote Controller4). Display content definition.

Display content Definition Display content DefinitionArm Arm Disarm Disarm

TEL Error Telephoneline failure TEL Back Telephone line

come back to normal

AC Loss AC power cut-off AC Back AC power come back to normal

MBAT Low Main batterypower low MBAT Back Main unit battery

come back to normal

Zx Low (x=1-8) Sensor in xzone power low Zx L Back (x=1-8) X zone sensor power

come back to normal

Zx Fire (x=1-8) Fire alarmin x zone Zx Gas (x=1-8) Gas leakage in x zone

Zx (x=1-8) EMC Emergencyalarm in x zone Zx (x=1-8) Medical Medical alarm in x

Zx (x=1-8) Theft Intrusion alarmin x zone

Zx Peri (x=1-8) Perimeter alarmin x zone

Zx Tamper (x=1-8) Tamper alarmin x zone Zx Com err (x=1-8) Communication

failure in x zone

Zx Open (x=1-8)

Display content Definition Display content Definition

X zone openinfrared sensor Zx Close (x=1-8) X close the

infrared sensor

Zx EMC (x=1-8) Emergency alarmin x user Ux Duress (x=1-8) Duress alarm in x user

Host Tamper Main unittamper alarm

5). Sound indicator

6.2 Code1) The installer code2) Master code

3) User code

4) Duress code.

: It is used to set main unit. Default code is 000000: It is used to Arm/Disarm/ modify user code/Date correct and Arm/Disarm

timer. Default code is 1234.: system can be programmed up to 8 user codes (no user code default). With user

code to Arm/Disarm corresponding zones.

Is formed by last digit of user code plus 1, (for example, the user code is 1234. The duress

(

Indicator DefinitionA short Bi- Valid indicator for keyboard indicatorTwo short Bi-Bi- Program operation correctly or arm indicatorFour short Bi-Bi-Bi-Bi- Power on inspect--self or disarm indicatorA long Di---- The wrong program indicatorA short Di- every second Phone line failure indicatorA short Bi- every two second Delay arm alert indicatorA short Di- every two second Delay alarm alert indicatorA long Bi---- every 1 minutes Main unit battery low indicator

¡ ¡

¡ ¡

¡ ¡

¡ ¡

¡ ¡

¡ ¡

¡ ¡

¡ ¡

27. 28.

code is 1235). If the last digit of user code is 9, the last digit of shall be 0 (for example, theuser code is 1239. the duress code is 1230). The user code is used when users are in duress.The users can cancel alarm and disarm system by duress code, but the system also send outthe alarm information through telephone to ask for help at the same time.

6.3 Arm/Disarm1). The remote controller programmed to arm/disarm for different partition.Press key

For Arm, Press key for disarm.2) Arm/disarm for different partition on panel keyboard.

the partition is in disarm state, press partition number and ARM key. Forexample you want quick arm partition 8 (partition 8 is in disarm state), just press 8 andARM one panel keyboard.

For example, if you want to disarm partition 8 (partition 8 in Arm state),press 8, the sounder will ask you enter the coder , then press the right user code andOK will disarm the partition 8.

if you adopt master code, 9 + master code + OK will Arm/Disarm allpartitions.

3). Arm/Disarm through timer.4). Arm/Disarm through remote telephone with user code or master code.

The user code Arm/Disarm is only for corresponding partition. Master coder for allPartition Arm/DisarmDuring Arm/Disarm operation, the sounder Bi- Bi- is for Arm. The Arm light

indicator will be on and the corresponding zone will enter arm state. For the delay Armzones, the main unit won t enter Arm state until delay time arrives. During the delay timethere is a sounder Bi- very two seconds to alert users to leave before delay timearrives.

Quick Arm,

Quick Disarm,¡ ¡ ［

］

［ ］ ［ ］ ［ ］

¡ ¡

¡

¡ ¡

Note:

Note:

Note:

6.4 Alarm Operation1). Intrusion alarm

2) Emergency Alarm

3) Duress alarm

The zone attribute in Intrude Alarm or Perimeter alarm , They won t activate until mainunit in Arm state. So don t forget to ARM main unit before leaving home.

Press key for emergency help in urgent situation, the alarm activate by emergency keywill dial all stored phone numbers and start up on-site siren.

When you are in duress by robber, press the duress code. The alarm system will be disarm,but it sends duress information through phone dialer.

¡ ¡ ¡

¡

Note: If delay alarm time is set, then the duress alarm will delay. During the leaving time, themain unit will make a Di sound every two second, then you can disarm this system tostop alarm.

1) ADEMCO alarm manage center process automatically2) Process by handWhen main unit dials the phone numbers pre-set, it plays the recorded message your stored.And give you 5 seconds after displaying message. During 5 seconds you are able to press 5#,4#, 2# or 0# on your phone or mobile phone.Press 5# to display message you stored repeatedly.Press 4# to listen for 30 seconds sound from location of main unit. During the 30 seconds, anyoperation is ineffective. You can enter other commands (see appendix 4) after 30 seconds. If nooperations in following 30 seconds, the system will dial next phone number your set up.Press 2# to stop alarming and disarm the main unit. It will not dial other phone numbers youstored any more.Press 0# to exit this call, and dial next phone number your stored. But system will dial thisnumber later in turn.If you receive call from main unit and have not any operations. It will play message 5 timesrepeatedly and dial next phone number.Message format: Ding-Dong, please attention!! record , zone number and alarm attribute.¡ ［ ］

6.5 When you receive an alarm

29. 30.

6.6 Remote SetupYou are able to dial phone number connected with main unit through your phone or mobilephone. When the ringing times you set up arrives, the main unit will ask you Please entercode¡, then you have to enter user code and # on your phone keypad. (If no operations beyond5 seconds, there is another indicator Please enter code . It will be repeated three times andthen hang up). One Du- eans the code is correct. Then you can enter directive youwanted. You are also can press 4# to listen for 30 seconds sound from main unit location.During the time, any operations is invalid. For more directive, you are able to see appendix 4.If no operations beyond 30 seconds, the phone will be hung up. If incorrect code was enteredfor three times continuously, the phone will be hung up.

¡

¡ ¡

¡ ¡ msound

Appendix 4

Directive Definition Command Definition1# Arm 2# Disarm3# Start up on-site siren 4# Listen to on-site sound6# Start up linkage device 7# Shut down linkage device8# Shut down on-site siren 0# exit

6.7 Record Inquiry

1)In standby time, press 1 + OK to read the latest Armrecord, LCD display will show as picture 28, The time is thelatest arm time. U02 tell you it is armed by the second user.

［ ］ ［ ］

¡ ¡

2)In standby time, press 2 + OK to read the latest disarmrecord, LCD display will show as picture 29. The time is thelatest disarm time. U02 tell you disarmed by second user.

3)In standby time, press 3 + OK to quickly read alarmrecord up to 20 pieces, and press * or # for up or downRecords.

［ ］ ［ ］

¡ ¡

［ ］ ［ ］

［ ］ ［ ］

7. Main Technical Specification7.1 Alarm ConsoleSize:Weight:Working Power:Aux Power:Wireless Frequency:Wireless Transceiver Distance:

Alarm Loudness:Working Environment:

17.50cm x 19.5cm x 5.4cm (Lx W x H), excluding length of antenna.1.5KG including backup battery.

AC220V 15% (optional power, 110V 10%), battery: 12V/1.3Ah500mA(with battery)

433.92 MHz

Distance between main unit and wireless PIR detector 400m in open areaDistance between main unit and Remote controller/door sensor 200m in open areaDistance between main unit and wireless siren 400m

90dB within 1m0 -55 , Humidity:40-70%

+ +≤

≥

≥

≥

≥

℃ ℃

≤ u

7.2 Remote ControllerWorking Voltage: Standby Current:Emit Power: Emit Frequency:

12V 27A 5 A10mW 433.92 Mhz≤

8. PrecautionOperate8.1 Do not set the stored phone number to Police or Fire police directly without authorized.8.2 Do not allowed to put alarm console and all accessories into water.8.3 Correct date and time in time once alarm console power on.8.4 The alarm host is not explosion-proof, which cannot be directly deployed at the

locations of Hazard Class I, II or III (i.e., where there are flammable, explosive steamgas, dusts, fibers and etc of certain concentration). Otherwise, it will be very dangerous

8.5 Do not disassemble the alarm console so as not to cause accidents and damage theapparatus.

8.6 Please contact the client service department or local agent in time if there is somethingbroken

8.7 Please periodically perform routinely inspect so as to clear troubles in time to avoidalarm missing.

U 0 2A r m

Picture 28

U 02D is arm

Picture 29

31. 32.

9. Frequently Asked QuestionQuestion Express Answer

Zone communicationfailure report

If the main unit do not receivesign from the zone beyond 26hours, it will send the reportof zonecommunication failure

1.Check the sensor tosee if it is work normally.2.Or check the distance betweenmain unit and sensor to see ifthe sensor is far away frommain unit.

When press the key on remotecontroller, the indicator isnot on, or the distance betweenremote controller and main unitis short.

12V power supplied in remotecontroller is run out.

Please replace the battery

Low power report from wireless The sensor powersupplied is run out Please replace the battery

Fault alarm happen fromwireless sensor frequently

The sensor is installedin incorrect place.

Please install the sensorin the right place accordingrequirement

The wired zone cause analarm when power up or Arm.

1.The wired sensor connectedis incorrect or bad connection.

2.The zone type be programmedas end-of-line resistor, butnot resistor is connected.

3.Not correctly connect bothnegative terminal and signalterminal for the zone thatis not sensor connected.

For the zones that not sensorconnected are asked to connectsignal terminal correctly orbypass them.

To see if the 2.2k end-of-lineresistor is connected. If not,please connect 2.2k resistor

Check the power cable to seeif the plus terminal andsignal terminal are connectedcorrectly. Or see if terminalconnection is loose

3.Check PIR sensor to see iffeature of timing report isclose.

Question Express Answer

Communication failurewhile alarm and dialing

Telephone communicationprotocol is not programmed.

Please program telephonecommunication protocol rightly.

The telephone can not dialout while alarm

The telephone hole and linehole are connected crossly.

Correct the telephone holeand line hole correctly.

Wireless PIR DetectorUser¡s Manual

Wireless Passive Infrared Sensor adopts advanced digit signal processing technologywith automatic temperature compensation, Lower power alert and timing communicationreport. It detects human infrared heat energy to emit wireless digit signal to activate alarmhost. It is advantage in low rate of false alarm, stable and easy installation.

1.Main Functions And Features1. Adopt dual infrared sensor, high sensitivity.2. Single-chip intelligent digit processing3. Double-channel intelligent signal processing4. Low power consumption design, static current 50 A, anti-pet, anti-

electromagnetism interference and low rate of false alarm5. Three classes of sensitivity.6. Automatic temperature compensation7. Adapter DC9V-12V is available. Automatically switch between inner power and

external power.

≤ μ

S33. 34.

8. With power lower alert and send signal to alarm host to report.9. Timing communication report and ON/OFF report.

2.Technical Parameter1. Detective distance 8m≤

2. Detective angle: 90¡3. Working Voltage: DC6V (4pcs No.7 dry batteries),

and external power (adapter): DC9V 12V.～

4. Working Current:Power supplied by battery, Standard current 50 A, Alarm current 15mA≤ μ ≤

Power supplied by the adapter, Standard current 5mA, Alarm current 15mA≤ ≤

5. Blocked time when it is power on: 100 seconds6. Emission time: 3 seconds7. Emission Frequency: 433.92MHz8. Emission power 70mW≤

9. Physical size: 110mm X 60mm X 45mm10. Working temperature:0 +55℃～ ℃

11. Preserving temperature:-25 +65℃～ ℃

Side elevalien

Plan form3.Component Description3.1 Working Mode:

3.2 Tamper:

There is three Mode Switch: Testing Mode, Normal Mode, Powersaving mode.

A: Test Mode: After it sends a signal, the sensor won t send a new signal until 5 seconds.It is recommended for debugging. This mode run more power.

B: Normal Mode: After it sends a signal, the sensor won t send a new signal until 60seconds. It is recommended for daily work.

C: Power Saving Mode: After it sends a signal, the sensor won t send a new signal until in240 seconds. It is used in marketing place where have more people in and out.

Note: The mode should be changed when power off (including batteries power)When DOS shell be opened or destroyed illegally, PIR detector will

¡

¡

¡

Lower power indicator

Alarm IndicatorInfrared Sensor

Sensitivity Selection

Power on./off

Transmitting Code JumperExternal DC in

Working Mode

Tamper

send signal to alarm host and activate alarm.tamper alarm can be activated in 24 hours aday. Even the sensor is in power off state.

3.3 Put switch to ON position,the detector will start to work, Put switch toOFF position, the detector will stop workingand report to main unit at the same time.

4 DC9V 12V is available(polarity ), External power supplied

power supplied can be changedautomatically.

Power On/Off:

External DC in

¡ ¡

¡ ¡

3. : ～

and inner

4.Installation Requirement and Diagram4.1. Installation Requirements

4.1.1 The infrared detector has the highest sensitivity when a human body moves parallelwith the mirror surface and the sensitivity is the lowest when a human body movesvertically against the mirror. As the angle and height against the horizontal surfaceshould be noted during installation, which will greatly effect the range of thedefense area. The high shall be 2 meter or so and the angle against the wall.

4.1.2 Stand off the straight light and other straight light source (e.g. car light)4.1.3 Stand off the warm or cold sources, e.g., warm air or cold air outlet, air conditioning

outlet, electric radiators, air cooling machines and etc. stand off from the windows.4.1.4 There is no barrier within the defended area of a detector.4.1.5 If infrared detector works in temperature that is near human temperature, the

detective effect is inefficient. So in this instance, Infrared detector is suggested tobe installed in lower temperature in that area.

4.1.6 In interference instance, infrared detector is suggested to set in low sensitivityposition.

4.1.7 Infrared detector is asked to be stable on the wall without sway.4.2. Diagram

35. 36.

1.Open cover as shown

4.2 Open top cover of detector, select the sensitivity class and working mode according tosecurity requirements.

4.3 Install 4pcs No.7 batteries according to battery case remark. Put ON/OFF switch to¡ON position, and fix it on the wall.

¡¡

Top View

2.Transmitting Code Jumper

8-12m5-9m4-6m

Working Mode Se lect Normal Mode Saving Pow er M ode

3. Press universal ball intouniversal bearer. To voiddamaged, please energizeon average

4.Fix universal bracket withnail on 2m over horizontal.

5.Fix infrared detector inuniversa l bracket .

6.top view, adjust detectorarea right and left,

7. side view, adjustun and down

8.installationfinished detector

4.3. Indicator

Alarm Indicator:Power Lower Indicator:

When happens alarm, alarm indicator will be flashing.When power is lower, lower power indicator will be on

4.4. Simulating Demo

After powering on for 100 seconds, human body motions in 0.75m/S by 8-10m in distance.Its alarm indicator is on and it activates alarm host to alarm. That means installation iscorrect and success.

5.Note

Working Modetest mode Normal Mode Power Saving Mode

4.1.1 To void its sensitivity, infrared sensor is not allowed to be touched by hand. Andhave to keep clear. It the surface is dirty, power off and clear it with a cotton balldipped in 75% alcohol.

4.1.2 Test infrared detector periodically4.1.3 This infrared detector can prevent theft conduct, but not insure no risk at all. For

security, users are asked to use this products correctly and improve alert in daily

Wireless Door SensorUser¡s Manual

1. InstructionWireless door sensor matches with a magnet. It sends alarm signal to alarm console whenboth parts seperated. The door sensor is designed in micro power consumption with lowpower alert. The wireless transmitter adopts SAWF. It is more stable. The transmittingdistance in open area can reach to 250m or more.

Magnet Door sensor

37. 38.

2. InstallationRemove the paper on double-faced glue on both door sensor and magnet.Glue sensor and magnet in proper place you want. Be sure the antenna of door sensor to bein uprightness (up or down).

3. Note1. The magnet part is asked to be installed in mobile door or window. For example, install

magnet art on mobile place. And install sensor part on fixed place.2.The distance of both magnet part and sensor part is not beyond 10MM.3. Please pull out the antenna to be sure the wireless transceiver effect.4. Please replace the battery once you find out the Alarm/Low Power Indicator is in red.

4. Component Diagram21 3 4

1. Transmitting Code Jumper2. Magnet:3. Low Power Indicator:4. Alarm Indicator:

: To change wireless code with jumper place.To match with sensor to perform alarm.

Red indicator for power lower.Red indicator for alarm,

39.