catalog 0802, fitting & tubing - rad-online.com convum/0802 (g) fittings... · catalog...

Pneumatic1 Parker Hannifin Corporation

Pneumatic DivisionRichland, Michiganwww.parker.com/pneumatic

G

Fittings & Tubing

Section G



Pneumatic Control ComponentsFittings & Tubing

Catalog 0802-2/USA

Notes



G

Advantages, Assembly, Ordering Information ....................................................... 4

62ML, 62MLBH, 66ML, 66MLBH.......................................................................... 5(Unions, Bulkhead Unions, Female Connectors, Female Bulkheads)

W68ML, 68ML, W68MLR, 68MLR, 362ML ........................................................... 6(Male Connectors, Round Body Male Connectors, Union Y Connectors)

364ML, 365ML, W368ML, 368ML ........................................................................ 7(Union Tees, Unions Elbows, Union Y Male Connectors)

W369ML, 369ML, W369MLX, 369MLX ................................................................ 8(Male Elbow Swivel, Extended Male Elbow Swivel)

W371ML, 371ML, W372ML, 372ML .................................................................... 9(Male Run Tee Swivel, Male Branch Tee Swivel)

Polyethylene Tubing ....................................................................................... 10-11

N Tubing, NR Tubing ...................................................................................... 12-13

Tubing Technical Information ......................................................................... 14-19

Pneumatic Control ComponentsFittings & Tubing

Catalog 0802-2/USA

Index



Assembly Instructions1. Cut thermoplastic tubing squarely, using tube cutter.

Metal tubing should be cut squarely and free of burrs.Be certain the port or mating part is clean and free ofdebris.

2. Insert tubing into fitting until it bottoms. A slight twistingmotion will ease the insertion. Pull on tubing to verify itis properly retained in the fitting.

3. To disassemble, simply push the collet against the bodyand remove tubing.

OrderBy part number and name.

NomenclaturePart numbers are constructed from symbols that identifythe style and size of the fitting. The first series of numbersand letters identify the style and type fitting. The secondseries of numbers describe the size.

Note: 0 indicates 10-32 UNF Thread

Example W 68 ML –4 –2

White ArcylicThread Sealant

Male Connector

Microlok

1/4" (4/16) Tube O.D.

1/8" (2/16) Pipe Thread

SizesTube sizes are determined by the number of sixteenths ofan inch in the tube O.D..

AdvantagesReady-to-use miniature one piece fitting for use with mostthermoplastic and soft copper tubing. This fitting wasdesigned to meet the needs of the motion control industrywhere fast assembly, disassembly and reassembly isimportant. No special tools needed for assembly; just insertthe tubing until it bottoms. Microlok is designed to be usedwithout a tube support to provide full flow through thetubing. The collet design of Microlok grips the tubingsecurely to provide tubing retention. The Microlok fittingcomes in externally threaded hex and round straight fittingbody styles and in a range of shaped configurations.Microlok straight fittings have a nickel plated brass bodyand shaped fittings have a composite body with nickelplated brass componentry. Microlok external pipe threadscome with a pre-applied white acrylic sealant. Positionalexternal pipe threaded ends are featured on shapes forinstallation in compact areas and for precise positioning.Microlok should not be used for live swivel applications.

MaterialsMicrolok Straights: CA360, CA345 (nickel plated)Microlok Shape Bodies: Reinforced Polyphenylene Oxide (PPO)

O-Ring: Nitrile (other compounds available on request)

Collet: Nickel Plated Brass

ApplicationsUse with Series “U”, “LU” and “HU” polyurethane tubing,series “E” polyethylene tubing or series “N” nylon tubing.Microlok was designed to meet the needs of the motioncontrol industry. Consult the factory with any questionsregarding special product applications. All applicationsshould be carefully tested through the range of conditionswhich may be encountered prior to use.

Working Pressure andTemperature Ranges32° to +150°F at up to 150 PSI depending on tubing beingused. Vacuum applications are dependent upontemperature and type of tubing used.

Fittings & TubingMicrolok Fittings

Catalog 0802-2/USA

Basic Features



G

DO.D.

L

DO.D.

L 12

D

L

P

B

C Hex

D

L

C Hex

D

L

P C Hex

B

Equal Union 62MLPart Tube FlowNo. Size O.D. L Dia D.62ML-2 1/8 .34 1.02 .09362ML-5/32 5/32 .38 1.03 .11062ML-4 1/4 .47 1.10 .19062ML-6 3/8 .63 1.32 .31262ML-8 1/2 .75 1.43 .406

Unequal Union 62MLPart Tube Tube FlowNo. Size 1 Size 2 O.D. L Dia. D62ML-5/32-2 5/32 1/8 .38 1.03 .09362ML-4-2 1/4 1/8 .47 1.09 .09362ML-4-5/32 1/4 5/32 .47 1.09 .11062ML-4-6 1/4 3/8 .63 1.23 .19062ML-6-8 3/8 1/2 .75 1.37 .312

Bulkhead Union 62MLBHPart Tube C P FlowNo. Size B Hex Max. L Dia. D62MLBH-2 1/8 3/8 1/8 .51 1.02 .09362MLBH-5/32 5/32 7/16 1/2 .51 1.03 .11062MLBH-4 1/4 1/2 5/8 .55 1.10 .19062MLBH-6 3/8 5/8 3/4 .55 1.32 .31262MLBH-8 1/2 3/4 7/8 .60 1.43 .406

Female Connector 66MLPipe

Part Tube Thread C FlowNo. Size NPTF Hex L Dia D.66ML-2-2 1/8 1/8 9/16 .99 .09366ML-2-4 1/8 1/4 11/16 1.22 .09366ML-5/32-2 5/32 1/8 9/16 .98 .11066ML-5/32-4 5/32 1/4 11/16 1.19 .11066ML-4-2 1/4 1/8 9/16 .99 .19066ML-4-4 1/4 1/4 11/16 1.20 .19066ML-4-6 1/4 3/8 13/16 1.24 .19066ML-6-4 3/8 1/4 11/16 1.28 .31266ML-6-6 3/8 3/8 13/16 1.28 .31266ML-6-8 3/8 1/2 1 1.44 .31266ML-8-6 1/2 3/8 13/16 1.35 .40666ML-8-8 1/2 1/2 1 1.58 .406

Female Bulkhead 66MLBHPipe

Part Tube Thread B C P FlowNo. Size NPTF Thread Hex Max L Dia D.66MLBH-2-4 1/8 1/4 3/8-24 11/16 .31 1.22 .09366MLBH-5/32-2 5/32 1/8 7/16-24 9/16 .36 1.07 .11066MLBH-5/32-4 5/32 1/4 7/16-24 9/16 .36 1.29 .11066MLBH-4-2 1/4 1/8 1/2-24 9/16 .36 1.06 .19066MLBH-4-4 1/4 1/4 1/2-24 11/16 .36 1.25 .19066MLBH-6-6 3/8 3/8 5/8-18 13/16 .36 1.34 .31266MLBH-8-6 1/2 3/8 3/4-16 13/16 .36 1.41 .40666MLBH-8-8 1/2 1/2 3/4-16 1 .36 1.64 .406


Catalog 0802-2/USA

Part Numbers & Dimensions



Microlok Male Connector W68MLPart Tube Pipe C Assm. Ht. FlowNo. Size Thread Hex N M Dia. DW68ML-2-1 1/8 1/16 3/8 .50 .49 .094W68ML-2-2 1/8 1/8 7/16 .46 .49 .09468ML-2-0 1/8 10-32 3/8 .58 .49 .078W68ML-5/32-1 5/32 1/16 7/16 .53 .49 .094W68ML-5/32-2 5/32 1/8 7/16 .33 .49 .110W68ML-5/32-4 5/32 1/4 5/8 .45 .49 .11068ML-5/32-0 5/32 10-32 7/16 .60 .49 .078W68ML-4-1 1/4 1/16 7/16 .64 .52 .140W68ML-4-2 1/4 1/8 1/2 .52 .52 .220W68ML-4-4 1/4 1/4 5/8 .46 .52 .220W68ML-4-6 1/4 3/8 11/16 .50 .52 .22068ML-4-0 1/4 10-32 7/16 .60 .52 .078W68ML-6-2 3/8 1/8 5/8 .81 .63 .220W68ML-6-4 3/8 1/4 5/8 .73 .63 .312W68ML-6-6 3/8 3/8 11/16 .54 .63 .312W68ML-6-8 3/8 1/2 7/8 .63 .63 .312W68ML-8-4 1/2 1/4 3/4 .94 .68 .314W68ML-8-6 1/2 3/8 3/4 .78 .68 .440W68ML-8-8 1/2 1/2 7/8 .63 .68 .440

Microlok Round Body Male Connector W68MLRAssm.

Part Tube Pipe Body Internal Ht. FlowNo. Size Thread Dia. H Hex N M Dia. D68MLR-2-0 1/8 10-32 .34 — .57 .49 .078W68MLR-5/32-1 5/32 1/16 .38 1/8 .55 .49 .126W68MLR-5/32-2 5/32 1/8 .43 1/8 .56 .49 .12668MLR-5/32-0 5/32 10-32 .38 — .57 .49 .078W68MLR-4-1 1/4 1/16 .47 5/32 .68 .52 .156W68MLR-4-2 1/4 1/8 .47 3/16 .59 .52 .188W68MLR-4-4 1/4 1/4 .59 3/16 .51 .52 .18868MLR-4-0 1/4 10-32 .47 — .58 .52 .094

Union Y Connector 362MLPart Tube Mounting FlowNo. Size Hole Dia. L N N1 Dia. D362ML-2 1/8 .13 1.02 .64 .33 .060362ML-5/32 5/32 .13 1.08 .71 .38 .080362ML-4 1/4 .13 1.23 .90 .48 .130

D

M

H

N

D

M

H

N

68MLR-X-0

5/32" and larger straight Microlok round body Male Connectors withPipe Threads have an internal hex for the use of an Allen Key to allowthe fitting to be mounted in any position. This also permtis close portingnot possible with a standard wrench.

D

MN

C Hex

D

M

N

C Hex

68ML-X-0

L

D

NN1


Catalog 0802-2/USA




G

Union Tee 364MLComposite BodyPart Tube Mounting FlowNo. Size Hole Dia. L G Dia. D364ML-2 1/8 .13 .56 .43 .081364ML-5/32 5/32 .13 .58 .46 .110364ML-4 1/4 .13 .67 .53 .190364ML-6* 3/8 — .96 — .250364ML-8* 1/2 — 1.11 — .370* 3/8 & 1/2 have no mounting hole

Union Elbow 365MLComposite BodyPart Tube Mounting FlowNo. Size Hole Dia. L Dia. D365ML-2 1/8 .13 .56 .081365ML-5/32 5/32 .13 .58 .110365ML-4 1/4 .13 .67 .190365ML-6* 3/8 — .96 .250365ML-8* 1/2 — 1.09 .370* 3/8 & 1/2 have no mounting hole

Union Y Male Connector 368MLPart Tube Pipe Mounting FlowNo. Size Thread Hole Dia. L N N1 Dia. D368ML-2-0 1/8 10-32 .13 1.28 .64 .33 .060W368ML-2-1 1/8 1/16 .13 1.42 .64 .33 .060W368ML-2-2 1/8 1/8 .13 1.42 .64 .33 .060368ML-5/32-0 5/32 10-32 .13 1.35 .71 .38 .078W368ML-5/32-1 5/32 1/16 .13 1.48 .71 .38 .080W368ML-5/32-2 5/32 1/8 .13 1.48 .71 .38 .080368ML-4-0 1/4 10-32 .13 1.48 .90 .47 .078W368ML-4-1 1/4 1/16 .13 1.62 .90 .47 .130W368ML-4-2 1/4 1/8 .13 1.62 .90 .47 .130W368ML-4-4 1/4 1/4 .13 1.96 .90 .47 .130

G

L

L

D

L

L

D

L

D NN1

L

NN1D

368ML-X-0


Catalog 0802-2/USA




Male Elbow Swivel 90° W369MLComposite Body

Assm.Part Tube Pipe C Ht. FlowNo. Size Thread Hex L N Dia D369ML-2-0 1/8 10-32 3/8 .56 .45 .078W369ML-2-1 1/8 1/16 3/8 .56 .48 .110W369ML-2-2 1/8 1/8 7/16 .56 .40 .110W369ML-2-4 1/8 1/4 9/16 .46 .54 .110369ML-5/32-0 5/32 10-32 3/8 .58 .45 .078W369ML-5/32-1 5/32 1/16 3/8 .58 .48 .110W369ML-5/32-2 5/32 1/8 7/16 .58 .40 .110W369ML-5/32-4 5/32 1/4 5/8 .58 .49 .110369ML-4-0 1/4 10-32 3/8 .67 .54 .078W369ML-4-1 1/4 1/16 3/8 .67 .57 .156W369ML-4-2 1/4 1/8 7/16 .67 .49 .195W369ML-4-4 1/4 1/4 9/16 .67 .57 .195W369ML-4-6 1/4 3/8 11/16 .55 .68 .195W369ML-6-2 3/8 1/8 3/4 .96 .87 .220W369ML-6-4 3/8 1/4 3/4 .96 .87 .250W369ML-6-6 3/8 3/8 3/4 .96 .93 .250W369ML-6-8 3/8 1/2 7/8 .96 1.04 .250W369ML-8-4 1/2 1/4 15/16 1.09 1.04 .313W369ML-8-6 1/2 3/8 15/16 1.09 1.05 .375W369ML-8-8 1/2 1/2 1 1.09 1.12 .376

Extended Male Elbow Swivel W369MLXAssm.

Part Tube Pipe Mounting C Ht. FlowNo. Size Thread Hole Dia. Hex L N Dia D369MLX-2-0 1/8 10-32 .13 3/8 .56 .84 .078W369MLX-2-1 1/8 1/16 .13 3/8 .56 .85 .081W369MLX-2-2 1/8 1/8 .13 7/16 .56 .77 .081369MLX-5/32-0 5/32 10-32 .13 3/8 .58 .86 .078W369MLX-5/32-1 5/32 1/16 .13 3/8 .58 .86 .106W39MLX-5/32-2 5/32 1/8 .13 7/16 .58 .78 .106W369MLX-5/32-4 5/32 1/4 .13 9/16 .58 .86 .106369MLX-4-0 1/4 10-32 .13 3/8 .70 1.00 .078W369MLX-4-1 1/4 1/16 .13 3/8 .67 1.05 .156W369MLX-4-2 1/4 1/8 .13 7/16 .67 .93 .190W369MLX-4-4 1/4 1/4 .13 9/16 .67 1.00 .190W369MLX-6-4* 3/8 1/4 — 3/4 .96 1.62 .250W369MLX-6-6* 3/8 3/8 — 3/4 .96 1.62 .250W369MLX-6-8* 3/8 1/2 — 7/8 .96 1.79 .250W369MLX-8-4* 1/2 1/4 — 15/16 1.09 1.79 .313W369MLX-8-6* 1/2 3/8 — 15/16 1.09 1.95 .375W369MLX-8-8* 1/2 1/2 — 1 1.09 2.02 .376* 3/8 & 1/2 have no mounting hole

N

L

D

C

N

L

D

C

369ML-X-0

N

L

D

C

369MLX-X-0

D

N

L

C


Catalog 0802-2/USA




G

Male Run Tee Swivel W371MLComposite Body

Assm.Part Tube Pipe Mounting C Ht. FlowNo. Size Thread Hole Dia. Hex L N Dia D371ML-2-0 1/8 10-32 .13 3/8 .56 .85 .078W371ML-2-1 1/8 1/16 .13 3/8 .56 .85 .081W371ML-2-2 1/8 1/8 .13 7/16 .56 .77 .081371ML-5/32-0 5/32 10-32 .13 3/8 .58 .85 .078W371ML-5/32-1 5/32 1/16 .13 3/8 .58 .86 .106W371ML-5/32-2 5/32 1/8 .13 7/16 .58 .78 .106371ML-4-0* 1/4 10-32 — 3/8 .67 1.00 .078W371ML-4-1* 1/4 1/16 — 3/8 .67 1.05 .156W371ML-4-2* 1/4 1/8 — 7/16 .67 .93 .190W371ML-4-4* 1/4 1/4 — 9/16 .67 1.00 .190W371ML-6-4* 3/8 1/4 — 3/4 .96 .97 .250W371ML-6-6* 3/8 3/8 — 3/4 .96 .94 .250W371ML-6-8* 3/8 1/2 — 7/8 .96 1.05 .250W371ML-8-4* 1/2 1/4 — 15/16 1.11 1.07 .313W371ML-8-6* 1/2 3/8 — 15/16 1.11 1.08 .375W371ML-8-8* 1/2 1/2 — 1 1.11 1.15 .376* 1/4, 3/8 & 1/2 have no mounting hole

Male Branch Tee Swivel W372MLComposite Body

Assm.Part Tube Pipe Mounting C Ht. FlowNo. Size Thread Hole Dia. Hex L N Dia D372ML-2-0 1/8 10-32 .13 3/8 .56 .85 .078W372ML-2-1 1/8 1/16 .13 3/8 .56 .85 .081W372ML-2-2 1/8 1/8 .13 7/16 .56 .77 .081372ML-5/32-0 5/32 10-32 .13 3/8 .58 .85 .078W372ML-5/32-1 5/32 1/16 .13 3/8 .58 .86 .106W372ML-5/32-2 5/32 1/8 .13 7/16 .58 .78 .106372ML-4-0* 1/4 10-32 — 3/8 .67 1.00 .078W372ML-4-1* 1/4 1/16 — 3/8 .67 1.05 .156W372ML-4-2* 1/4 1/8 — 7/16 .67 .93 .190W372ML-4-4* 1/4 1/4 — 9/16 .67 1.00 .190W372ML-6-2* 3/8 1/8 — 3/4 .96 .91 .220W372ML-6-4* 3/8 1/4 — 3/4 .96 1.00 .250W372ML-6-6* 3/8 3/8 — 3/4 .96 .97 .250W372ML-6-8* 3/8 1/2 — 7/8 .96 1.08 .250W372ML-8-4* 1/2 1/4 — 15/16 1.11 1.04 .313W372ML-8-6* 1/2 3/8 — 15/16 1.11 1.05 .375W372ML-8-8* 1/2 1/2 — 1 1.11 1.12 .376* 1/4, 3/8 & 1/2 have no mounting hole

L

C

D

N

371ML-X-0

N L

C

D

D

N

L

C

372ML-X-0

D

N

L

C


Catalog 0802-2/USA




Fittings & TubingPolyethylene Tubing

Catalog 0802-2/USA

Features & Part Numbers

AdvantagesChemical resistant, flexible, low cost,eight colors, five tube sizes and choiceof reel lengths.

ConstructionFlexible polyethylene thermoplastictubing is extruded from high molecularweight resin for increased dimensionalstability, uniformity and long-termstrength. Its resistance to environmentalstress cracking greatly exceeds thatof ordinary polyethylene tubing asmeasured by ASTM D-1693, (10%IGEPAL).

Applications &ApprovalsPolyethylene tubing is available in blackas well as seven coding colors asrecommended by the InstrumentSociety of America. Black (EB) tubingcontains an ultra-violet inhibitor whichis recommended for use in sunlitareas. Ingredients of natural and colortubing (except black) listed below meetFDA requirements for food contactapplications. All tubing conforms toASTM D-1248, Type I, Class A,Category 4, Grade E5.

Temperature RangeSuggested operating temperature rangeis -80°F to 150°F (-62°C to 66°C).

FittingRecommendation• Brass fittings

NomenclaturePart numbers are constructed fromsymbols that identify the style and sizeof the fitting. Letters identify style andmaterial. Numbers identify size in 1/16’sof an inch.

Example:E - 6 4 - Y - 0500

Polyethylene3/8" (6/16) Tube O.D.1/4" (4/16) Tube I.D.Color, YellowReel Footage

E Instrument Grade TubingWorking Min. Min. Weight

Reel Pressure Burst Bend PerPart Length psi at psi at Radius 100Number Color O.D. I.D. Wall Feet 73°F 73°F Inches FeetE-43-0100 Natural 1/4 .170 .040 100 120 625 1 1.1

E-43-0500 Natural 1/4 .170 .040 500 120 625 1 1.1E-43-1000 Natural 1/4 .170 .040 1000 120 625 1 1.1EB-43-0100 Black 1/4 .170 .040 100 120 625 1 1.1

EB-43-0500 Black 1/4 .170 .040 500 120 625 1 1.1EB-43-1000 Black 1/4 .170 .040 1000 120 625 1 1.1E-43-R-0100 Red 1/4 .170 .040 100 120 625 1 1.1

E-43-R-0500 Red 1/4 .170 .040 500 120 625 1 1.1E-43-B-0100 Blue 1/4 .170 .040 100 120 625 1 1.1E-43-B-0500 Blue 1/4 .170 .040 500 120 625 1 1.1

E-43-O-0500 Orange 1/4 .170 .040 500 120 625 1 1.1E-43-Y-0500 Yellow 1/4 .170 .040 500 120 625 1 1.1E-43-P-0500 Purple 1/4 .170 .040 500 120 625 1 1.1

E-43-G-0500 Green 1/4 .170 .040 500 120 625 1 1.1E-53-0500 Natural 5/16 .187 .062 500 145 800 1-1/8 2.1EB-53-0500 Black 5/16 .187 .062 500 145 800 1-1/8 2.1

E-64-0100 Natural 3/8 .250 .062 100 125 675 1-1/4 2.5E-64-0500 Natural 3/8 .250 .062 500 125 675 1-1/4 2.5EB-64-0100 Black 3/8 .250 .062 100 125 675 1-1/4 2.5

EB-64-0500 Black 3/8 .250 .062 500 125 675 1-1/4 2.5E-64-R-0500 Red 3/8 .250 .062 500 125 675 1-1/4 2.5E-64-B-0500 Blue 3/8 .250 .062 500 125 675 1-1/4 2.5

E-64-O-0500 Orange 3/8 .250 .062 500 125 675 1-1/4 2.5E-64-Y-0500 Yellow 3/8 .250 .062 500 125 675 1-1/4 2.5E-64-P-0500 Purple 3/8 .250 .062 500 125 675 1-1/4 2.5

E-64-G-0500 Green 3/8 .250 .062 500 125 675 1-1/4 2.5E-86-0100 Natural 1/2 .375 .062 100 90 425 2-1/2 3.6EB-86-0100 Black 1/2 .375 .062 100 90 425 2-1/2 3.6

E-108-0100 Natural 5/8 .500 .062 100 70 325 4 4.6EB-108-0100 Black 5/8 .500 .062 Coil 70 325 4 4.6



G

Fittings & TubingPolyethylene Tubing

Catalog 0802-2/USA


Construction &ApprovalsFlame resistant polyethylene ismanufactured from a distinctivelyformulated compound which meetsthe UL94 V-2 flame classification. Italso meets the flame spread, fuelcontr ibution and smoke densityrequirements of the ASTM E84-81atunnel test.

ApplicationsParker ser ies FRPE tubing is thepreferred product for pneumatic controlapplications in the heating- ventilating-air conditioning-energy conservationindustry. It is also suitable for use inpetrochemical plants, petroleumrefineries, pulp and paper mills, mines,steel mills and other industries whereprotection against intermittent flame andhot sparks is necessary.

Temperature RangeSuggested operating temperature range is -85°F to 150°F(-65°C to +66°C).

NomenclatureOrder by tubing part number and name.

Example:FR PE 4 — 0500

Flame ResistantPolyethylene1/4" (4/16) Tube O. D.Reel Footage

FRPE Flame Resistant TubingWorking Min. Min. Weight

Reel Pressure Burst Bend PerPart Length psi at psi at Radius 100Number Color O.D. I.D. Wall Feet 73°F 73°F Inches FeetFRPE2.5-0500 Black 5/32 .096 .030 500 225 900 1/2 .56FRPE4-0250 Black 1/4 .170 .040 250 160 650 3/4 1.24FRPE4-0500 Black 1/4 .170 .040 500 160 650 3/4 1.24

FRPE4-1000 Black 1/4 .170 .040 1000 160 650 3/4 1.24FRPE6-0250 Black 3/8 .250 .062 250 195 780 1-1/2 2.90FRPE6-0500 Black 3/8 .250 .062 500 195 780 1-1/2 2.90FRPE8-0250 Black 1/2 .375 .062 250 135 540 1-3/4 4.05



Fittings & TubingNylon Tubing – N

Catalog 0802-2/USA


AdvantagesFlexible nylon tubing is carefully made fromhigh-grade, abrasion-resistant, heat-andlight-stabilized nylon. Resistance to stress-cracking greatly exceeds that of ordinarynylon tubing. Extremely low level waterabsorption.

Chemical-resistant nylon tubing has theadditional benefits of better flexibility, lighterweight and resistance to flexural fatigue.

ColorsAvailable in natural (NN) and black (NB).Black tubing is recommended for useoutdoors and in sunlit areas.

Temperature RangeOperating temperatures, depending uponconditions, are -65°F to 200°F (-54°C to93°C) continuous.

Fitting Recommendations• Brass fittings


Example:N N — 2 — 016

NylonColor, Natural1/8" (2/16) Tube O.D.Wall Thickness in thousandths of an inch

N Flexible Tubing*Min.Burst Min. Std.

Nom. Nom. Average Pressure Bend ReelNylon Tube Tube Wall at 73°F Radius LengthPart No. Color O.D. I.D. Thick. psi Inches FeetNN-2-016 Natural 1/8 .093 .016 1000 1/4 250

NB-2-016 Black 1/8 .093 .016 1000 1/4 250NN-2-031 Natural 1/8 .064 .031 2000 1/4 250NB-2-031 Black 1/8 .064 .031 2000 1/4 250

NN-2.5-025 Natural 5/32 .106 .025 1200 1/2 250NB-2.5-025 Black 5/32 .106 .025 1200 1/2 250NN-3-025 Natural 3/16 .138 .025 1000 5/8 250


NN-4-035 Natural 1/4 .180 .035 1000 7/8 250NB-4-035 Black 1/4 .180 .035 1000 7/8 250NN-4-040 Natural 1/4 .170 .040 1250 7/8 250


NN-5-040 Natural 5/16 .233 .040 1250 1-1/8 250NB-5-040 Black 5/16 .233 .049 1250 1-1/8 250NN-6-050 Natural 3/8 .275 .050 1250 1-1/8 250

NB-6-050 Black 3/8 .275 .050 1250 1-1/8 250NN-6-093 Natural 3/8 .190 .093 2000 3/4 250NB-6-093 Black 3/8 .190 .093 2000 3/4 250

NN-8-062 Natural 1/2 .375 .062 1000 1-1/4 250NB-8-062 Black 1/2 .375 .062 1000 1-1/4 250NN-8-124 Natural 1/2 .253 .124 2000 1 250

NB-8-124 Black 1/2 .253 .124 2000 1 250*Suggested working pressure is 1/4 of burst pressure.



G

Fittings & TubingNylon Tubing – NR

Catalog 0802-2/USA


AdvantagesSeries NR semi-rigid nylon tubing offersbetter chemical resistance than series N,good resistance to high ambient temperatureand low moisture absortion. NR has a hightensile strength which will give excellentcoupling retention in high pressure,temperature and vibration environments.

ConstructionParker series NR tubing is manufacturedfrom a semi-rigid nylon II material. The tubingdoes not contain plasticizers.

Applications & ApprovalsNR tubing is specified for machine toollubricating systems, marine control systems,process lines for chemicals and oils andother applications requiring a high qualitynylon tube.

Temperature RangeThe recommended operating temperaturerange for service at rated pressures withcompatible fluids is -60°F to 200°F (-51°Cto 93°C).

Fitting Recommendations• Brass fittings


Example:N B R 2 016

NylonColor, BlackRigid1/8" (2/16) Tube O.D.Wall Thickness in thousandths of an inch

NR Semi-rigid High Strength Tubing*Min.Burst Min. Std.

Nom. Nom. Average Pressure Bend ReelNylon Tube Tube Wall at 73°F Radius LengthPart No. Color O.D. I.D. Thick. psi Inches FeetNNR-2-017 Natural 1/8 .091 .017 1700 1/2 500NBR-2-017 Black 1/8 .091 .017 1700 1/2 500

NNR-2-026 Natural 1/8 .073 .026 2500 3/8 500NBR-2-026 Black 1/8 .073 .026 2500 3/8 500NNR-3-024 Natural 3/16 .140 .024 1700 3/4 500

NBR-3-024 Black 3/16 .140 .024 1700 3/4 500NNR-3-039 Natural 3/16 .110 .039 2500 5/8 500NBR-3-039 Black 3/16 .110 .039 2500 5/8 500

NNR-4-035 Natural 1/4 .180 .035 1700 1 250NBR-4-035 Black 1/4 .180 .035 1700 1 250NNR-4-050 Natural 1/4 .150 .050 2500 7/8 250

NBR-4-050 Black 1/4 .150 .050 2500 7/8 250NNR-5-040 Natural 5/16 .233 .040 1700 1-1/2 250NBR-5-040 Black 5/16 .233 .040 1700 1-1/2 250

NNR-6-048 Natural 3/8 .279 .048 1700 1-3/4 250NBR-6-048 Black 3/8 .279 .048 1700 1-3/4 250NNR-6-075 Natural 3/8 .225 .075 2500 1-1/2 250

NBR-6-075 Black 3/8 .225 .075 2500 1-1/2 250NNR-8-062 Natural 1/2 .376 .062 1500 2-3/8 250NBR-8-062 Black 1/2 .376 .062 1500 2-3/8 250

NNR-8-075 Natural 1/2 .350 .075 2200 2-1/2 250NBR-8-075 Black 1/2 .350 .075 2200 2-1/2 250*Suggested working pressure is 1/4 of burst pressure.

PTC Plastic Tube CutterPart No. PTC

An easy to handle razor/edged tube cutter, closesautomatically, assuring clean and square cuts.

May be used with polyethylene, polypropylene, nylon andother plastic tubing.

How To UseInsert plastic tube to desired length, allow tube cutterto close, then apply pressure until tube snaps off.



MinimumBurstPressure(psig)

3.0 2.8 2.6 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0

75 100 125 150 175 200

(NR-2-026)(NR-3-039)(NR-4-050)(NR-6-075)

(NR-8-075)

Temperature (deg. F.)

MinimumBurst Pressure(psig)(Thousands)

1.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0

75 100 125 150 175 200

(N-4-040)

(N-2-016)(N-2.5-025)(N-3-025)(N-4-035)(N-5-040)(N-6-050)(N-8-062)


MinimumBurstPressure(psig)

2.0 1.9 1.8 1.7 1.6 1.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0

75 100 125 150 175 200

(NR-2-017)(NR-3-024)(NR-4-035)(NR-5-040)(NR-6-048)

(NR-8-062)


MinimumBurst Pressure(psig)(Thousands)

Nylon Semi-Rigid TubingNR Series (NNR, NBR)1/8 thru 1/2 O.D. Inches

Nylon Flexible TubingN Series (NN, NB)1/8 thru 1/2 O.D. Inches

Nylon Semi-Rigid TubingNR Series (NNR, NBR)1/8 thru 1/2 O.D. Inches

2000

1800

1600

1400

1200

1000

800

600

400

200

0 75 100 125 150 175 200


Nylon Flexible TubingN Series1/8 thru 1/2 O.D. Inches

Suggested working pressures are 1/4 of burst pressure at system operating temperature.

(N-2-031)(N-3-046)(N-4-062)(N-6-093)(N-8-124)

Fittings & TubingBurst Pressure / Temperature Charts

Catalog 0802-2/USA

Technical Information



G

Fittings & TubingBurst Pressure / Temperature Charts

Catalog 0802-2/USA


350

300

250

200

150

100

50

0 75 100 125 150 175 180

(U-21)

(U-42)


Polyethylene TubingLaboratory Grade E Series1/4 thru 5/8 O.D.

900

800

700

600

500

400

300

200

100

75 100 125 150

(E-53)

(E-108)


MinimumBurstPressure

900

800

700

600

500

400

300

200

100

0 75 100 125 150

(FRPE-2.5 x .030")(FRPE-6 x .062")

(FRPE-3 x .030")(FRPE-4 x .040")(FRPE-8 x .062")


(E-86)

(E-64)

(E-43)


Polyethylene Tubing“U” Series1/8 thru 1/4 O.D.Polyether Base


Polyethylene TubingFlame Resistant FRPE Series5/32 thru 1/2 O.D.

Suggested working pressures are 1/4 of burst pressure at system operating temperature.



All BrassBody Fittings Prestolok

(Except Prestolok) FittingRating Rating

Acetic Acid 4 4Acetic Anhydride 4 4Acetone 1 4Alum 4 4Aluminum Chloride 4 4Aluminum Sulfate 4 4Ammonium Hydroxide 4 4Ammonium Chloride 4 4Ammonium Nitrate 4 4Ammonium Sulfate 4 4Amyl Acetate 2 4Aniline 3 4Aniline Dyes 3 4Asphalt 1 2Barium Chloride 4 4Beer 2 4Beet Sugar Syrups 2 2Benzoic Acid 2 4Black Liquor, Sulfate Process 4 4Bleaching Powder, Wet 4 4Borax 1 2Bordeaux Mixture 2 2Boric Acid 2 2Bromine, Dry 1 4Bromine, Moist 4 4Butyric Acid 3 4Calcium Bisulfite 4 4Calcium Chloride 4 4Calcium Hydroxide 2 2Calcium Hypochlorite 4 4Cane Sugar Syrups 2 2Carbolic Acid 2 4Carbon Dioxide, Dry 1 1Carbon Dioxide, Moist 3 3Carbon Disulfide 1 4Carbon Tetrachloride, Moist 4 4Castor Oil 1 1Chlorine, Dry 1 4Chlorine, Moist 4 4Chloracetic Acid 4 4Chloroform, Dry 1 4



Citric Acid 3 3Coffee 1 4Copper Chloride 4 4Copper Sulfate 4 4Corn Oil 2 2Cottonseed Oil 2 2Creosote 2 2Crude Oil 3 3Ethers 1 4Ethyl Acetate 2 4Ethyl Chloride 3 3Ethylene Glycol 2 2Ferric Chloride 4 4Formaldehyde 3 3Furfural 3 4Gelatine 1 1Glucose 1 1Glycerine 1 1Hydrobromic Acid 4 4Hydrochloric Acid 4 4Hydrocyanic Acid 4 4Hydrofluoric Acid 4 4Hydrofluosilicic Acid 4 4Hydrogen Peroxide 3 4Hydrogen Sulfide, Moist 3 4Lacquers 1 4Lacquer Solvents 1 4Lactic Acid Cold 3 3Lime 1 1Lime-Sulfur 2 4Linseed Oil 2 2Magnesium Chloride 4 4Magnesium Hydroxide 1 2Magnesium Sulfate 3 3Methyl Chloride, Dry 1 4Milk 2 4Nitric Acid 4 4Nitrogen 1 1Oleic Acid 3 3Oxalic Acid 3 3Palmitic Acid 3 3

1 — SATISFACTORY2 — FAIR3 — RECOMMEND TESTING4 — UNSATISFACTORY

Fittings & TubingChemical Compatibility Guide - Brass Fittings

Catalog 0802-2/USA




G



Phosphoric Acid 4 4Potassium Chloride 4 4Potassium Cyanide 4 4Potassium Dichromate, Acid 4 4Potassium Hydroxide 3 3Potassium Sulfate 2 2Sea Water 3 3Soap Solutions 2 2Sodium Bicarbonate 3 3Sodium Bisulfate 4 4Sodium Bisulfite 4 4Sodium Carbonate 2 2Sodium Chloride 4 4Sodium Cyanide 4 4Sodium Hydroxide 3 3Sodium Hypochlorite 4 4Sodium Nitrate 3 3Sodium Peroxide 4 4Sodium Phosphate 2 2Sodium Silicate 2 2



Sodium Sulfite 4 4Sodium Thiosulfate 2 2Steam 3 4Stearic Acid 3 3Sulfur, Dry 1 4Sulfur Chloride, Dry 1 4Sulfur Dioxide, Dry 1 4Sulfur Dioxide, Moist 4 4Sulfur Trioxide, Dry 1 4Sulfuric Acid 4 4Sulfurous Acid 4 4Tar 2 2Tartaric Acid 3 3Toluene 1 4Trichloracetic Acid 4 4Trichlorethylene, Dry 1 3Trichlorethylene, Moist 3 3Vinegar 4 4Zinc Chloride 4 4Zinc Sulfate 4 4

1 — SATISFACTORY

2 — FAIR

3 — RECOMMEND TESTING

4 — UNSATISFACTORY

This brass compatibility chart is a ready reference forbrass fittings with various media. It is intended as aguide to chemical compatibility and has been compiledfrom the best available sources. Many factors(concentration, temperature, intermittent or continuousexposure, etc.) have a bearing upon the suitability ofany material and, therefore, no guarantee, expressedor implied, is made to compatibility in any specific setof circumstances.

Fittings & TubingChemical Compatibility Guide - Brass Fittings

Catalog 0802-2/USA




FRPEE Flame N NR

“E” Series Resistant Nylon NylonMedia Polyethylene Polyethylene “N” “NR”

Acetaldehyde L — L GAcetates G — L GAcetic Acid L — L GAcetic Anhydride L — P LAcetone G L L GAcetyl Bromide L — L —Acetyl Chloride L — L —Air G G G GAlcohols G G G GAluminum Salts G G G GAmmonia G L G GAmyl Acetate G — L GAniline L — L LAnimal Oils L — G GArsenic Salts G G G GAromatic Hydrocarbons P P L GBarium Salts G G G GBenzaldehyde P P L GBenzene (Benzol) P P L GBenzyl Alcohol P P L LBleaching Liquors G — L LBoric Acid Solutions G G G GBromine L — L PButane L — P GButanol G G G GButyl Acetate G G G GCalcium Salts G G G GCarbon Dioxide G G G GCarbon Disulfide L — L GCarbon Tetrachloride P P L LCaustic Potash G — G GCaustic Soda G — G GChloracetic Acid L — L LChlorine (Dry) L — L PChlorine (Wet) L — L PChlorobenzene P P L LChloroform P P L LChromic Acid L — P PCopper Salts G G G GCresol P P L PCyclohexanone L — L GEthers L — L GEthyl Acetate G — L GEthyl Alcohol G G L GEthylamine L — L LEthyl Bromide P P L LEthyl Chloride P P L LFatty Acids L P G GFerric Salts G — G GFormaldehyde G — L GFormic Acid L G L PFreon L — L GGasoline P P G G

Ratings Code (1)G — Good to excellent. Little or no swelling, tensile or surface changes. Preferred choice.L — Marginal or conditional. Noticeable effects but not necessarily indicating lack of serviceability. Further testing suggested

for specific application. Very long term effects such as stiffening or potential for crazing should be evaluated.P — Poor or unsatisfactory. Not recommended without extensive and realistic testing.— — Not tested.

NOTE: For Footnotes (1), (2), (3), (4), (5), (6), & (7), See Page 19.

FRPEE Flame N NR

“E” Series Resistant NylonNylonMedia Polyethylene Polyethylene “N” “NR”

Glucose G G G GGlycerine G G G GHydriodic Acid L — P LHydrochloric Acid (Conc.) L — L LHydrochloric Acid (Med. Conc.) L — L GHydrofluoric Acid L — P PHydrogen Peroxide (Conc.) L — L GHydrogen Peroxide (Dil.) L — L GHydrogen Sulfide G — G GIodine L — G GKerosene L — G GKetones G — G GLacquer Solvent L — L LLactic Acid G — G GLead Acetate G — G GLinseed Oil L — G GMagnesium Salts G — G GNaphtha L G G GNatural Gas L — G GNickel Salts G — G GNitric Acid (Conc.) P G P PNitric Acid (Dil.) P P L LNitrobenzene P P L LNitrogen Oxides L — L LNitrous Acid L — L LOils (Animal and Mineral) L — G GOils (Vegetable) L — L GOxygen G G G GPerchloric Acid P P P PPhenol P P P PPotassium Salts G G G GPyridine L — L LSilver Nitrate G G G GSoap Solutions G G G GSodium Salts G G G GStearic Acid L — G GSulfur Chloride L — L LSulfuric Acid (Conc.) P P P PSulfuric Acid (Dil.) P P G LSulfurous Acid P P L LTannic Acid G — G GTanning Extracts G — G GTitanium Salts G G G GToluene (Toluol) P P L GTrichloracetic Acid L — P PTrichlorethylene P P G LTurpentine L — G GUrea G — G GUric Acid G — G GWater G G G GXylene (Xylol) P P L GZinc Chloride G — G G

Fittings & TubingChemical Compatibility Guide (Tubing)

Catalog 0802-2/USA




G

Footnotes for Chemical Compatibility Guides forThermoplastic Fittings, Tubing and Hose

(1) The Chemical Compatibility Guides are simplified rating tabulations based on immersion tests at 75°F. Highertemperatures tend to reduce ratings. Since final selection depends on pressure, media and ambienttemperature and other factors not known to The Company, no performance guarantee is expressedor implied. Ratings do not imply compliance with specialized codes such as FDA, NSF, AGA or UL and donot cover possible fluid discoloration, taste or odor effects. For conveying foodstuffs use FDA sanctionedmaterials, and for potable water use NSF approved materials. For chemicals not listed, or for advice onparticular applications, please consult the supplier.

(2) Hose applications for these fluids must take into account legal and insurance regulations. This does notimply AGA or UL compliance.

(3) Satisfactory at some concentrations and temperatures, unsatisfactory in others.

(4) For high pressure gases, the cover should be pinpricked and the pressure must not be released quickly.Chain or restrain the hose to prevent personal injury in the event of damage or failure.

(5) Chemical compatibility does not imply low permeation rates. Consult the supplier for a recommendation foryour specific requirements.

(6) Does not imply NSF or FDA compliance.

(7) Chemical compatibility does not imply acceptability for use in airless paint spray applications. Theseapplications require a special conductive hose.

Fittings & TubingGuides Footnotes & Approvals

Catalog 0802-2/USA




The items described in this document and other documents or descriptions provided by Parker Hannifin Corporation, its subsidiariesand its authorized distributors, are hereby offered for sale at prices to be established by Parker Hannifin Corporation, its subsidiariesand its authorized distributors. This offer and its acceptance by any customer (“Buyer”) shall be governed by all of the following Termsand Conditions. Buyer’s order for any such item, when communicated to Parker Hannifin Corporation, its subsidiaries or an authorizeddistributor (“Seller”) verbally or in writing, shall constitute acceptance of this offer.

1. Terms and Conditions of Sale: All descriptions, quotations,proposals, offers, acknowledgments, acceptances and sales of Seller’sproducts are subject to and shall be governed exclusively by the termsand conditions stated herein. Buyer’s acceptance of any offer to sell islimited to these terms and conditions. Any terms or conditions in additionto, or inconsistent with those stated herein, proposed by Buyer in anyacceptance of an offer by Seller, are hereby objected to. No suchadditional, different or inconsistent terms and conditions shall becomepart of the contract between Buyer and Seller unless expressly acceptedin writing by Seller. Seller’s acceptance of any offer to purchase byBuyer is expressly conditional upon Buyer’s assent to all the terms andconditions stated herein, including any terms in addition to, or inconsistentwith those contained in Buyer’s offer. Acceptance of Seller’s productsshall in all events constitute such assent.

2. Payment: Payment shall be made by Buyer net 30 days from the dateof delivery of the items purchased hereunder. Amounts not timely paidshall bear interest at the maximum rate permitted by law for each monthor portion thereof that the Buyer is late in making payment. Any claimsby Buyer for omissions or shortages in a shipment shall be waivedunless Seller receives notice thereof within 30 days after Buyer’s receiptof the shipment.

3. Delivery: Unless otherwise provided on the face hereof, deliveryshall be made F.O.B. Seller’s plant. Regardless of the method ofdelivery, however, risk of loss shall pass to Buyer upon Seller’s deliveryto a carrier. Any delivery dates shown are approximate only and Sellershall have no liability for any delays in delivery.

4. Warranty: Seller warrants that the items sold hereunder shall be freefrom defects in material or workmanship for a period of 18 months fromdate of shipment from Parker Hannifin Corporation. THIS WARRANTYCOMPRISES THE SOLE AND ENTIRE WARRANTY PERTAINING TOITEMS PROVIDED HEREUNDER. SELLER MAKES NO OTHERWARRANTY, GUARANTEE, OR REPRESENTATION OF ANY KINDWHATSOEVER. ALL OTHER WARRANTIES, INCLUDING BUT NOTLIMITED TO, MERCHANTABILITY AND FITNESS FOR PURPOSE,WHETHER EXPRESS, IMPLIED, OR ARISING BY OPERATION OFLAW, TRADE USAGE, OR COURSE OF DEALING ARE HEREBYDISCLAIMED.

NOTWITHSTANDING THE FOREGOING, THERE ARE NOWARRANTIES WHATSOEVER ON ITEMS BUILT OR ACQUIREDWHOLLY OR PARTIALLY, TO BUYER’S DESIGN ORSPECIFICATIONS.

5. Limitation of Remedy: SELLER’S LIABILITY ARISING FROM ORIN ANY WAY CONNECTED WITH THE ITEMS SOLD OR THISCONTRACT SHALL BE LIMITED EXCLUSIVELY TO REPAIR ORREPLACEMENT OF THE ITEMS SOLD OR REFUND OF THEPURCHASE PRICE PAID BY BUYER, AT SELLER’S SOLE OPTION.IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL,CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY KIND ORNATURE WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOSTPROFITS ARISING FROM OR IN ANY WAY CONNECTED WITH THISAGREEMENT OR ITEMS SOLD HEREUNDER, WHETHER ALLEGEDTO ARISE FROM BREACH OF CONTRACT, EXPRESS OR IMPLIEDWARRANTY, OR IN TORT, INCLUDING WITHOUT LIMITATION,NEGLIGENCE, FAILURE TO WARN OR STRICT LIABILITY.

6. Changes, Reschedules and Cancellations: Buyer may request tomodify the designs or specifications for the items sold hereunder as wellas the quantities and delivery dates thereof, or may request to cancel allor part of this order, however, no such requested modification orcancellation shall become part of the contract between Buyer and Sellerunless accepted by Seller in a written amendment to this Agreement.Acceptance of any such requested modification or cancellation shall beat Seller’s discretion, and shall be upon such terms and conditions asSeller may require.

7. Special Tooling: A tooling charge may be imposed for any specialtooling, including without limitations, dies, fixtures, molds and patterns,acquired to manufacture items sold pursuant to this contract. Suchspecial tooling shall be and remain Seller’s property notwithstandingpayment of any charges by Buyer. In no event will Buyer acquire anyinterest in apparatus belonging to Seller which is utilized in themanufacture of the items sold hereunder, even if such apparatus hasbeen specially converted or adapted for such manufacture and

notwithstanding any charges paid by Buyer. Unless otherwise agreed,Seller shall have the right to alter, discard or otherwise dispose of anyspecial tooling or other property in its sole discretion at any time.8. Buyer’s Property: Any designs, tools, patterns, materials, drawings,confidential information or equipment furnished by Buyer, or any otheritems which become Buyer’s property, may be considered obsolete andmay be destroyed by Seller after two (2) consecutive years haveelapsed without Buyer placing an order for the items which aremanufactured using such property. Seller shall not be responsible forany loss or damage to such property while it is in Seller’s possessionor control.9. Taxes: Unless otherwise indicated on the face hereof, all prices andcharges are exclusive of excise, sales, use, property, occupational orlike taxes which may be imposed by any taxing authority upon themanufacture, sale or delivery of the items sold hereunder. If any suchtaxes must be paid by Seller or if Seller is liable for the collection of suchtax, the amount thereof shall be in addition to the amounts for the itemssold. Buyer agrees to pay all such taxes or to reimburse Seller thereforeupon receipt of its invoice. If Buyer claims exemption from any sales,use or other tax imposed by any taxing authority, Buyer shall save Sellerharmless from and against any such tax, together with any interest orpenalties thereon which may be assessed if the items are held to betaxable.10. Indemnity For Infringement of Intellectual Property Rights:Seller shall have no liability for infringement of any patents, trademarks,copyrights, trade dress, trade secrets or similar rights except asprovided in this Part 10. Seller will defend and indemnify Buyer againstallegations of infringement of U.S. patents, U.S. trademarks, copyrights,trade dress and trade secrets (hereinafter “Intellectual Property Rights”).Seller will defend at its expense and will pay the cost of any settlementor damages awarded in an action brought against Buyer based on anallegation that an item sold pursuant to this contract infringes theIntellectual Property Rights of a third party. Seller’s obligation to defendand indemnify Buyer is contingent on Buyer notifying Seller within ten(10) days after Buyer becomes aware of such allegations of infringement,and Seller having sole control over the defense of any allegations oractions including all negotiations for settlement or compromise. If anitem sold hereunder is subject to a claim that it infringes the IntellectualProperty Rights of a third party, Seller may, at its sole expense andoption, procure for Buyer the right to continue using said item, replaceor modify said item so as to make it noninfringing, or offer to acceptreturn of said item and return the purchase price less a reasonableallowance for depreciation. Notwithstanding the foregoing, Seller shallhave no liability for claims of infringement based on information providedby Buyer, or directed to items delivered hereunder for which the designsare specified in whole or part by Buyer, or infringements resulting fromthe modification, combination or use in a system of any item soldhereunder. The foregoing provisions of this Part 10 shall constituteSeller’s sole and exclusive liability and Buyer’s sole and exclusiveremedy for infringement of Intellectual Property Rights.If a claim is based on information provided by Buyer or if the design foran item delivered hereunder is specified in whole or in part by Buyer,Buyer shall defend and indemnify Seller for all costs, expenses orjudgements resulting from any claim that such item infringes anypatent, trademark, copyright, trade dress, trade secret or any similarright.11. Force Majeure: Seller does not assume the risk of and shall not beliable for delay or failure to perform any of Seller’s obligations by reasonof circumstances beyond the reasonable control of Seller (hereinafter“Events of Force Majeure”). Events of Force Majeure shall includewithout limitation, accidents, acts of God, strikes or labor disputes, acts,laws, rules or regulations of any government or government agency,fires, floods, delays or failures in delivery of carriers or suppliers,shortages of materials and any other cause beyond Seller’s control.12. Entire Agreement/Governing Law: The terms and conditions setforth herein, together with any amendments, modifications and anydifferent terms or conditions expressly accepted by Seller in writing,shall constitute the entire Agreement concerning the items sold, andthere are no oral or other representations or agreements which pertainthereto. This Agreement shall be governed in all respects by the law ofthe State of Ohio. No actions arising out of sale of the items soldhereunder or this Agreement may be brought by either party more thantwo (2) years after the cause of action accrues.

Offer of Sale

! WARNINGFAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBEDHEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provideproduct and/or system options for further investigation by users having technical expertise. It is important that you analyzeall aspects of your application including consequences of any failure, and review the information concerning the product orsystem in the current product catalog. Due to the variety of operating conditions and applications for these products orsystems, the user, through its own analysis and testing, is solely responsible for making the final selection of the productsand systems and assuring that all performance, safety and warning requirements of the application are met.The products described herein, including without limitation, product features, specifications, designs, availability and pricing,are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice.

Offer of SaleThe items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or itsauthorized distributors. This offer and its acceptance are governed by the provisions stated on the separate page of thisdocument entitled “Offer of Sale”.

© Copyright 2002, 2003 Parker Hannifin Corporation. All Rights Reserved

Pneumatic Pneumatic

GlobalPneumatics

This icon can be found next to products that are widelysupported by Parker Pneumatics’ worldwide manufacturingand sales network. When you see this icon, you can beconfident that this product is manufactured and/or stocked*worldwide for rapid delivery. In addition to local manufacturingor inventory, our sales network has been specifically trainedon these products to provide our customers with the bestpossible service.

Products not showing this icon are still sold and distributedworldwide. However, The Global Pneumatics icon representsproducts that customers can expect the best level of support.

If you are a multi-national company, seek global sourcing orship globally, depend on Parker Pneumatic for PREMIERCUSTOMER SERVICE.

* Stocking levels vary by country

Parker’s CharterTo be a leading worldwide manufacturer ofcomponents and systems for the builders and usersof durable goods. More specifically, we will design,market and manufacture products controllingmotion, flow and pressure. We will achieve profitablegrowth through premier customer service.

Product InformationNorth American customers seeking productinformation, the location of a nearby distributor,or repair services will receive prompt attentionby calling the Parker Product Information Centerat our toll-free number: 1-800-C-PARKER(1-800-272-7537). In Europe, call00800-C-PARKER-H (00800-2727-5374).

The Fluid ConnectorsGroup designs, manufacturesand markets rigid and flexibleconnectors, and associatedproducts used in pneumatic andfluid systems.

The Hydraulics Groupdesigns, produces andmarkets a full spectrum ofhydraulic components andsystems to builders andusers of industrial andmobile machinery andequipment.

The Automation Groupis a leading supplier ofpneumatic andelectromechanicalcomponents and systemsto automation customersworldwide.

The Seal Group designs,manufactures anddistributes industrial andcommercial sealing devicesand related products byproviding superior qualityand total customersatisfaction.

The Filtration Groupdesigns, manufactures andmarkets quality filtrationand clarification products,providing customers withthe best value, quality,technical support, and globalavailability.

The InstrumentationGroup is a global leader inthe design, manufacture anddistribution of high-qualitycritical flow components forworldwide processinstrumentation, ultra-high-purity, medical andanalytical applications.

About Parker Hannifin CorporationParker Hannifin is a leading global motion-controlcompany dedicated to delivering premier customerservice. A Fortune 500 corporation listed on the NewYork Stock Exchange (PH), our components andsystems comprise over 1,400 product lines thatcontrol motion in some 1,000 industrial andaerospace markets. Parker is the only manufacturerto offer its customers a choice of hydraulic,pneumatic, and electromechanical motion-controlsolutions. Our Company has the largest distributionnetwork in its field, with over 7,500 distributorsserving nearly 400,000 customers worldwide.

Parker Hannifin Corporation6035 Parkland Blvd.Cleveland, Ohio 44124-4141Telephone: (216) 896-3000Fax: (216) 896-4000www.parker.com

Parker Hannifin Corporation

The Aerospace Group isa leader in the development,design, manufacture andservicing of control systemsand components for aerospaceand related high-technologymarkets, while achievinggrowth through premiercustomer service.

The Climate & IndustrialControls Group designs,manufactures and marketssystem-control and fluid-handling components andsystems to refrigeration, air-conditioning and industrialcustomers worldwide.

Parker Hannifin CorporationPneumatic DivisionRichland, Michiganwww.parker.com/pneumatic

Parker Hannifin CorporationPneumatic DivisionRichland, Michiganwww.parker.com/pneumatic

Pneumatic

Catalog 0802-2/USA 05/2004 10M IGS Printed in U.S.A.

Catalog 0802-2/USA

Parker Hannifin CorporationPneumatic Division8676 E. M89P.O. Box 901Richland, MI 49083 USATel: (269) 629-5000Fax: (269) 629-5385

Customer/Technical Service

Tel: (269) 629-5575Fax: (269) 629-5385Web site: www.parker.com/pneumaticE-mail: [email protected]

Vacuum ProductsCups, Generators, Sensors,Vacuum Control Valves, Cylindersand Accessories

Vacuum

Pro

ducts

Cu

ps, G

en

era

tors, S

en

sors, V

ac

uu

m C

on

trol V

alve

s,C

ylind

ers a

nd

Ac

ce

ssorie

s

catalog 0802, fitting & tubing - rad-online.com convum/0802 (g) fittings... · catalog...

Documents