cartridge filter cartridge

CARTRIDGE

FILTERS

AND

ACCESSORIES

At USFilter, our mission is to provide the products and services you

need to meet your water requirements — anytime, anyplace. An

example of this offering is our complete line of cartridge filtration

products shown in this catalog. Be it a sediment removal filter

for the pretreatment of an RO system or validated submicron

filtration of water used to manufacture

WFI quality water, USFilter is your one

stop source for your filtration needs. As the

world’s largest water treatment company,

we offer a wide range of other capabilities, reliable products and

services, combined with experience and technical knowledge you can

trust. Give us a call so we can work with you to deliver a solution that

meets your most stringent specifications. Call our 24-hour Customer

Service at 800-466-7873 for information and support.

Cartridge Filters and Accessories

CARTRIDGE END-CAPS . . . . . . . . . . . . . . . . . . . . . . . . 2

NOMINALLY-RATED CARTRIDGES

DI Gard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

ROGARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

NT Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Prepure DP™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Postpure PP™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

ABSOLUTE-RATED CARTRIDGES

NA Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

WN Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

WE Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

DI Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

VH Series (Validated) . . . . . . . . . . . . . . . . . . . . . . 12

PV Series (Validated) . . . . . . . . . . . . . . . . . . . . . . 13

VENT FILTERS

EA Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

VP Series (Validated) . . . . . . . . . . . . . . . . . . . . . . 15

Vent Capsule . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

SPECIALTY FILTERS

UF Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Point-of-Use Capsule. . . . . . . . . . . . . . . . . . . . . . . 18

Pulverized Activated Carbon . . . . . . . . . . . . . . . . . 19

Granular Activated Carbon . . . . . . . . . . . . . . . . . . 20

HOUSINGS

316 Stainless Steel, Single Tube (Code F). . . . . . . . . 21

316L Stainless Steel, Single Tube (Code 0) . . . . . . . . 22

304 Stainless Steel, 5-Round, Multi-Tube . . . . . . . . . 23

304 Stainless Steel, 6-Round, Multi-Tube . . . . . . . . . 24

316 Stainless Steel, Multi-Tube . . . . . . . . . . . . . . . . 25

316L Electropolished Stainless Steel, Multi-Tube . . . . 26

Plastic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Natural Polypropylene . . . . . . . . . . . . . . . . . . . . . 28

T A B L E O F

C O N T E N T S

Taking Care of the World's Water

24-HR CUSTOMER SERVICE: (800) 466-7873 2

Code 10 Style CartridgeSingle open end with

1-120 internal O-Ring at open end

Code F Style CartridgesFlat gaskets

Code O Style Cartridges2-222 O-Ring Outlet

Code 5 Style Cartridges2-222 O-Ring Outlet with spear assembly

Code 7 Style Cartridges2-226 O-Ring locking outlet with spear assembly

CARTRIDGE DESIGN DESCRIPTION CODE

Gaskets compressed on knife edge seal Fof housing

O-rings are located externally 0on the cartridge, other end flat

O-rings are located externally 5on the cartridge, other end spear

227 O-rings are located externally 7on the cartridge. The O-ring adapter locks into the housing. Spear assembly on other end

Single O-ring located inside 10the cartridge

The following table is presented as reference when ordering filter cartridges. For moredetailed information, please contact our Technical Support Team at 800-875-7873 ext. 5000.

Cartridge End Cap Configuration

TECHNICAL SUPPORT (800) 875-7873 EXT. 5000 3

DI GARD™ String Wound Prefiltration Cartridges

CARTRIDGE SPECIFICATIONSDimensions

Diameter (OD) . . . . . . . . . . 2.5" (6.5 cm)Length (in) . . . . . . . . . . . . 9.75, 10, 19.5, 20, 29.25, 30, 40

Materials

FCCS . . . . . . . . . . . . . . . . . Bleached white cotton fiber string media with polypropylene coreFCPS . . . . . . . . . . . . . . . . . Polypropylene fiber string media with polypropylene core FCPX . . . . . . . . . . . . . . . . . Surfactant-free polypropylene fiber string media with polypropylene coreNOTE: Code F cartridges (0.5 µm) have santophrene end seals.

Operating Parameters

Maximum Temperature . . . . . . . . . . . . . . . . . 140°F (60°C)Maximum Differential Pressure @ 25°C. . . . . 50 psi (3.4 bar)Micron Ratings . . . . . . . . . . . . . . . . . . . . . . . 0.5, 1, 3, 5, 10, 20, 50 MicronsFiltration Efficiency . . . . . . . . . . . . . . . . . . . . Nominal 90%

Recommended Water Flow Rates

5.0 gpm/10" length (18.9 lpm/10" length)

ORDERING INFORMATIONCatalog Number and Description

FCXX . . . . . . . . . . . . . . . . FCCS = cotton string fiber cartridgeFCPS = polypropylene string fiber cartridgeFCPX = surfactant-free polypropylene string fiber cartridge

F. . . . . . . . . . . . . . . . . . . . Cartridge Code: F = double open end

XX . . . . . . . . . . . . . . . . . . Length (in): 09 = 9.75, 10 = 10, 19 = 19.5, 20 = 20, 29 = 29.25, 30 = 30, 40 = 40

XX . . . . . . . . . . . . . . . . . . Micron Rating: S5 = 0.5µm, 01 = 1 µm, 03 = 3 µm, 05 = 5 µm, 10 = 10 µm, 20 = 20 µm, 50 = 50 µm

To figure your order number, replace the X with one of the numbered or lettered optionsbeside it. Note: Not all part number combinations are available; consult TechnicalSupport for assistance.

• Designed for a variety of prefiltration applications such as SDI (service deionization),reverse osmosis, and CDI® (Continuous Deionization) Systems

• String wound type filter with your choice of cotton, industrial or surfactant-freepolypropylene string over a polypropylene core

• Large void volume design for low-cost, reliable filtration performance with highcontaminant holding capacity

• Continuous filter winding in 20-, 30-, and 40-inch lengths prevents by-passing orexcessive pressure drops at the seams

• Gasketed end caps on 0.5 µm rated filters for positive sealing that eliminates by-passing

• Surfactant-free FCPX style filter meets USP Class VI Biological Tests for Plastics requirements

2.0Cle

an P

ressu

re D

rop

(PSI

D)

BAR

LPM

1.6

.14

.08

.04

.02

1.2

.8

.4

00 1 2 3 4 5

50 µm

20 µm

10 µm5 µm3 µm

1µm0.5 µm

FLOW RATE vs. INITIAL CLEAN PRESSURE DROP

Water Flow Rate/10" cartridge (GPM)

4 12 168


ROGARD™ Graded Density PolypropyleneMedia Filter Cartridge


Diameter (OD) . . . . . . . . . . 2.5" (6.5 cm)Length (in) . . . . . . . . . . . . 9.75, 10, 12, 19.5, 20, 30, 31, 40

Materials

Media . . . . . . . . . . . . . . . . Melt Blown polypropyleneCore . . . . . . . . . . . . . . . . . Integral polypropylene coreO-Rings . . . . . . . . . . . . . . . Silicone o-ringsGaskets . . . . . . . . . . . . . . . Santophrene end seals


Maximum Temperature . . . . . . . . . . . . . . . . . 160°F (70°C)Maximum Differential Pressure @ 25°C. . . . . 50 psi (3.4 bar)Micron Ratings . . . . . . . . . . . . . . . . . . . . . . . 1, 3, 5, 10, 20, 25, 50, 75 micronsFiltration Efficiency . . . . . . . . . . . . . . . . . . . . Nominal 90%


5.0 gpm/10" length (18.9 lpm/10" length)


FCRO. . . . . . . . . . . . . . . . . Rogard II all polypropylene depth cartridge

X . . . . . . . . . . . . . . . . . . . Cartridge Code: F = double open end (1&5 µm w/gasket) 0 = 2-222 o-rings (12&20", 1&5 µm only)N = double open end (1, 3 & 5 µm – no gasket)

XX . . . . . . . . . . . . . . . . . . Length (in): 09 = 9.75, 10 = 10, 12 = 12, 19 = 19.5, 20 = 20, 30 = 30, 31 = 31, 40 = 40

XX . . . . . . . . . . . . . . . . . . Micron Rating: 01 = 1 µm, 03 = 3 µm, 05 = 5 µm, 10 = 10 µm,20 = 20 µm, 25 = 25 µm, 50 = 50 µm, 75 = 75 µm


• Designed for a variety of prefiltration applications such as SDI (service deionization), reverse osmosis and CDI® (Continuous Deionization) Systems

• Graded density melt spun polypropylene media design for exceptional throughput, with high contaminant holding capacity

• Gasketed end caps on 1, 3 and 5 µm rated filters for positive sealing that eliminates by-passing

• ROGARD cartridge filters meet the criteria for USP Class VI Biological Tests for Plastics, ensuring that no surfactants or coatings interfere with the application, making these cartridges ideal for use in the food and beverage industry

• Available in a variety of lengths and pore sizes to meet a wide range of applications

Clean

Pre

ssure

Dro

p (PS

ID)

BAR

Water Flow Rate/10" Cartridge (GPM)

.2

.3

75µm

50µm

25µm20µm

10µm5µm1µm 3µm

4 32 LPM2812 16 20 248

.02

.01

.03

2 3 5 7 91 4 6 8 100

.05

.1

.15

.25

.35

.4

.45



NT Series Graded Pore Polypropylene Depth Filter Cartridge


Diameter (OD) . . . . . . . . . . 2.5" (6.5 cm)Length (in) . . . . . . . . . . . . 9.75, 10, 20, 30, 40

Materials

Cartridge . . . . . . . . . . . . . . Polypropylene caps and coreMedia . . . . . . . . . . . . . . . . CoLD fiber melt blown polypropyleneSeals . . . . . . . . . . . . . . . . . Silicone o-rings and gaskets


Maximum Temperature . . . . . . . . . . . . . . . . . 180°F (82°C) @ 15 psid (1.0 bar)Maximum Differential Pressure @ 30°C. . . . . 60 psi (4.1 bar)Filtration Efficiency . . . . . . . . . . . . . . . . . . . . Nominal 90%


0.5 – 3 micron. . . . . . . . . . 2.0 gpm/10" length (7.6 lpm/10" length)5 – 75 micron . . . . . . . . . . 5.0 gpm/10" length (18.9 lpm/10" length)

Sanitizing Agents

Chlorine, hydrogen peroxide


FCNT . . . . . . . . . . . . . . . . . Polypropylene CoLD depth filter cartridge

X . . . . . . . . . . . . . . . . . . . Cartridge Code: 1 = double open end w/ internal o-ringsF = double open end (0.5 – 5 mm w/gasket)N = double open end (0.5 – 5 mm – no gasket)

XX . . . . . . . . . . . . . . . . . . Length (in): 09 = 9.75, 10 = 10, 20 = 20, 30 = 30, 40 = 40

XX . . . . . . . . . . . . . . . . . . Micron Rating: S5 = 0.5 µm, 01 = 1 µm, 03 = 3 µm, 05 = 5 µm, 10 = 10 µm, 15 = 15 µm, 20 = 20 µm, 30 = 30 µm, 40 = 40 µm, 50 = 50 µm, 75 = 75 µm


• Designed to deliver precision prefiltration through the patented advanced melt blownCoLD® technology structure that incorporates large diameter fibers for strength whilemaintaining small fibers for filtration

• CoLD fiber technology melt blown structure delivers exceptional retention, mechanicalstrength and on-stream life

• Graded pore structure throughout the filter’s depth provides high contaminant holding capacity

• High purity, 100% polypropylene construction is free of surfactants, binders and adhesives

• FDA listed materials of construction

CoLD is a registered trademark of Filterite Corporation.

Clean

Pre

ssure

Dro

p (PS

ID)

BAR


3

5

15µm20µm

10µm

5µm

3µm

1µm0.5µm

.3

.2

.1

.4

2 3 5 7 91 4 6 8 100

1

2

4

6

7


4 32 36 LPM2812 16 20 248Cle

an P

ressu

re D

rop (

PSID

)

BAR


0.3

0.5

75µm

30µm40µm50µm .03

.02

.01

.04

2 3 5 7 91 4 6 8 100

0.1

0.2

0.4

0.6

0.7


4 32 36 LPM2812 16 20 248




Materials

Cartridge . . . . . . . . . . . . . . Polypropylene caps, core and cageMedia . . . . . . . . . . . . . . . . Non-woven melt blown polypropyleneSeals . . . . . . . . . . . . . . . . . Silicone o-rings and gaskets


Maximum Temperature . . . . . . . . . . . . . . . . . 140°F (60°C) @ 30 psid (2.1 bar)Maximum Differential Pressure @ 20°C. . . . . 60 psi (4.1 bar)Filtration Efficiency . . . . . . . . . . . . . . . . . . . . Nominal 90%


0.5 – 5 micron. . . . . . . . . . 2.0 gpm/10" length (7.6 lpm/10" length)10 – 50 micron . . . . . . . . . 5.0 gpm/10" length (18.9 lpm/10" length)

Sanitizing Agents

Chlorine or hydrogen peroxide


FCDP . . . . . . . . . . . . . . . . . All polypropylene depth filter cartridge

X . . . . . . . . . . . . . . . . . . . Cartridge Code: 0 = 2-222 o-rings 7 = 2-226 o-rings w/spear1 = double open end w/internal o-ringsF = double open end w/flat gasket seal

XX . . . . . . . . . . . . . . . . . . Length (in): 09 = 9.75, 10 = 10, 20 = 20, 30 = 30, 40 = 40

XX . . . . . . . . . . . . . . . . . . Micron Rating: S5 = 0.5 µm, 01 = 1 µm, 03 = 3 µm, 05 = 5 µm, 10 = 10 µm, 25 = 25 µm, 50 = 50 µm

To figure your order number, replace the X with one of the numbered or letteredoptions beside it. Note: Not all part number combinations are available; consultTechnical Support for assistance.

Prepure DP™ Graded Density PolypropyleneDepth Media Filter Cartridge

• Composed of graded density melt blown polypropylene depth media for high efficiency prefiltration and post-filtration of DI resin applications

• Prepure DP filtration cartridges feature high contaminant loading due to graded densitydepth filtration media construction

• Filter meets the criteria for USP Class VI Biological Tests for Plastics, ensuring that no surfactants or coatings interfere with the application, making these ideal for use in the food and beverage industry

• All materials are FDA listed for contact with food and beverages.

• Virgin polypropylene construction with fusion welding minimizes extractables

Clean

Pre

sure

Dro

p (PS

ID)


.2

0

.4

.6

.8

1.2

1.4

1.6

1.8

2.0

2.4

3.0

50 µm

25 µm10 µm

5 µm

3 µm

1 µm

0.5 µm

1 2 3 4 5

LPM


4 12 168

BAR

.18

.04

.06

.02

.12

.14

.10


Postpure PP™ Graded Density PleatedPolypropylene Depth Media FilterCartridge

CARTRIDGE SPECIFICATIONS

Dimensions

Diameter (OD) . . . . . . . . . . 2.6" (6.6 cm)Length (in) . . . . . . . . . . . . 10, 20, 30

Materials

Cartridge . . . . . . . . . . . . . . Polypropylene caps, core and cageMedia . . . . . . . . . . . . . . . . Pleated, non-woven melt blown polypropyleneSeals . . . . . . . . . . . . . . . . . Silicone o-rings and gaskets


Maximum Temperature . . . . . . . . . . . . . . . . . 140°F (60°C) @ 40 psid (2.8 bar)Maximum Differential Pressure @ 25°C. . . . . 75 psi (5.1 bar)Filtration Efficiency . . . . . . . . . . . . . . . . . . . . nominal 90%


0.3 – 1 micron. . . . . . . . . . 2.0 gpm/10" length (7.6 lpm/10" length)3 – 30 micron . . . . . . . . . . 8.0 gpm/10" length (30.1 lpm/10" length)

Sanitizing Agents

Chlorine, hydrogen peroxide, in-line with hot water (82°C) for one hour, autoclaved for 20 minutes at 121°C under no load conditions.


FCPP . . . . . . . . . . . . . . . . . All polypropylene, pleated, nominal depth filter cartridge

X . . . . . . . . . . . . . . . . . . . Cartridge Code: 0 = 2-222 o-rings 7 = 2-226 o-rings locking tabs w/spear1 = double open end w/internal o-ringsF = double open end w/flat gasket seal

XX . . . . . . . . . . . . . . . . . . Length (in): 10 = 10, 20 = 20, 30 = 30

XX . . . . . . . . . . . . . . . . . . Micron Rating: S3 = 0.3 µm, S6 = 0.6 µm, 01 =1 µm, 03 = 3 µm, 05 = 5 µm, 10 = 10 µm, 30 = 30 µm


• Composed of graded-density, pleated, polypropylene depth media for high efficiency postfiltration of DI resin applications

• Filter components meet USP Class VI Biological Tests for Plastics, ensuring that no surfactants or coatings interfere with the application, making these ideal for use in the food and beverage industry

• Postpure DP filtration cartridges feature high contaminant loading due to gradeddensity depth filtration media construction


• All materials are FDA listed for contact with food and beverages

Clean

Pre

ssure

Dro

p (PS

ID)


0.5

1.0

1.5

2.0

2.5

3.0

.05

0

.10 BAR

.15

.20

2 4 6 8 100

0.3 µ

m

0.6 µm

1 µm

3 µm

5 µm10 & 30 µm

LPM


8 24 3216


NA Series Absolute Rated PolypropyleneDepth Filter Cartridge

• Designed to deliver precision filtration through the patented advanced melt blown CoLD®

technology structure that incorporates large diameter fibers for strength while maintaining small fibers for filtration

• Patented CoLD fiber technology melt blown structure provides outstanding retentionefficiency, mechanical strength, and long on-stream life

• Multi-zone design produces a gradient pore structure to provide pre- and post-filtration in a single cartridge

• Absolute filtration with sharp particle cutoffs deliver precise removal efficiencies

• High purity, 100% polypropylene construction is free of surfactants, binders and adhesives making these cartridges ideal for use in food and beverage applications



Materials

Cartridge . . . . . . . . . . . . . . Polypropylene caps and coreMedia . . . . . . . . . . . . . . . . CoLD fiber melt blown polypropyleneSeals . . . . . . . . . . . . . . . . . Silicone o-rings and gaskets


Maximum Temperature . . . . . . . . . . . . . . . . . 180°F (82°C) @ 15 psid (1.0 bar)Maximum Differential Pressure @ 30°C. . . . . 60 psi (4.1 bar)Filtration Efficiency . . . . . . . . . . . . . . . . . . . . 100% Absolute


0.5 – 5 micron. . . . . . . . . . 2.0 gpm/10" length (7.6 lpm/10" length)10 – 70 micron . . . . . . . . . 5.0 gpm/10" length (18.9 lpm/10" length)

Sanitizing Agents



FCNA. . . . . . . . . . . . . . . . . Absolute rated CoLD depth filter cartridge

X . . . . . . . . . . . . . . . . . . . Cartridge Code: 0 = 2-222 o-rings7 = 2-226 o-rings w/spear1 = double open end w/ internal o-ringsF = double open end w/flat gasket seal5 = 2-222 o-rings w/spear

XX . . . . . . . . . . . . . . . . . . Length (in): 09 = 9.75, 10 = 10, 20 = 20, 30 = 30, 40 = 40

XX . . . . . . . . . . . . . . . . . . Micron Rating: S5 = 0.5 µm, 01 = 1 µm, 03 = 3 µm, 05 = 5 µm, 10 = 10 µm, 15 = 15 µm, 20 = 20 µm, 30 = 30 µm, 50 = 50 µm, 70 = 70 µm


Clean

Pre

ssure

Dro

p (PS

ID)

BAR


3

5

15µm20µm

10µm

5µm

1µm 3µm0.5µm

.3

.2

.1

.4

2 3 5 7 91 4 6 8 100

1

2

4

6

7


4 32 36 LPM2812 16 20 248Cle

an P

ressu

re D

rop (

PSID

)

BAR


0.3

0.5

30µm

50µm

70µm.03

.02

.01

.04

2 3 5 7 91 4 6 8 100

0.1

0.2

0.4

0.6

0.7


4 32 36 LPM2812 16 20 248


WN Series Pleated Polysulfone Membrane Filter Cartridge



Materials

Cartridge . . . . . . . . . . . . . . Polypropylene caps, core and cageMedia . . . . . . . . . . . . . . . . Single layer asymmetric hydrophilic polysulfoneSeals . . . . . . . . . . . . . . . . . Silicone o-rings and gaskets




0.05 micron . . . . . . . . . . . . 1.3 gpm/10" length (4.9 lpm/10" length)0.1 micron. . . . . . . . . . . . . 1.7 gpm/10" length (6.4 lpm/10" length)0.2 micron. . . . . . . . . . . . . 3.0 gpm/10" length (11.3 lpm/10" length)0.45 micron . . . . . . . . . . . . 5.5 gpm/10" length (20.8 lpm/10" length)

Sanitizing Agents

5% Chlorine, 3% hydrogen peroxide


FCWN . . . . . . . . . . . . . . . . Filter cartridge single layer polysulfone

X . . . . . . . . . . . . . . . . . . . Cartridge Code: 0 = 2-222 o-rings5 = 2-222 o-rings w/spear1 = double open end w/ internal o-rings7 = 2-226 o-rings w/locking tabs/spear endF = double open end w/flat gasket seal

XX . . . . . . . . . . . . . . . . . . Length (in): 09 = 9.75, 10 = 10, 20 = 20, 30 = 30, 40 = 40

XX(X) . . . . . . . . . . . . . . . Micron Rating: S05 = 0.05 µm, S1 = 0.1 µm, S2 = 0.2 µm, S4 = 0.45 µm


• Composed of pleated highly asymmetric polysulfone membrane over a non-woven polypropylene support layer

• For high flow rates and low pressure drops, absolute rated filters are designed for postfiltration in high purity water applications

• The highly asymmetric membrane delivers longer on-stream life than conventional membrane products

• High-purity construction materials are factory rinsed with DI water for quick on-streamrinse up with a minimum of throughput

• All polypropylene parts and thermal welding minimizes extractables

• All materials are FDA listed and meet criteria for USP Class VI Biological tests forplastics, ensuring that no surfactants or coatings interfere with the application

Clean

Pre

ssure

Dro

p (PS

ID) 3.0

2.5

1.5

0.5

2.0

1.0

0 1 2 3 4 5 6 7

BAR

0.05µm 0.1µm

0.2µm

0.45µm


LPM


4 12 2416 208




Materials

Cartridge . . . . . . . . . . . . . . Polypropylene caps, core and cageMedia . . . . . . . . . . . . . . . . Double layer asymmetric hydrophilic polysulfoneSeals . . . . . . . . . . . . . . . . . Silicone o-rings and gaskets



Recommended Water Flow Rates0.02 micron . . . . . . . . . . . . 0.6 gpm/10" length (2.3 lpm/10" length)0.1 micron. . . . . . . . . . . . . 1.2 gpm/10" length (4.5 lpm/10" length)0.2 micron. . . . . . . . . . . . . 2.2 gpm/10" length (8.3 lpm/10" length)0.45 micron . . . . . . . . . . . . 3.2 gpm/10" length (12.1 lpm/10" length)

Sanitizing Agents

5% Chlorine or 3% hydrogen peroxide

Integrity Test

Pore Size . . . . . . . . . . . . . . Diffusional Flow (cc/min) @ Test Pressure per 10" length0.02 micron . . . . . . . . . . . . 20 @ 50 psig (3.4 bar)0.1 micron. . . . . . . . . . . . . 24 @ 25 psig (1.7 bar)0.2 micron. . . . . . . . . . . . . 18 @ 20 psig (1.4 bar)0.45 micron . . . . . . . . . . . . 15 @ 15 psig (1.0 bar)


FCWE. . . . . . . . . . . . . . . . . Filter cartridge double layer polysulfone

X . . . . . . . . . . . . . . . . . . . Cartridge Code: 0 = 2-222 o-rings5 = 2-222 o-rings w/spear1 = single open end w/ internal o-ring7 = 2-226 o-rings w/locking tabs/spear endF = double open end w/flat gasket seal

XX . . . . . . . . . . . . . . . . . . Length (in): 09 = 9.75, 10 = 10, 20 = 20, 30 = 30, 40 = 40

XX(X) . . . . . . . . . . . . . . . Micron Rating: S02 = 0.02 µm, S1 = 0.1 µm, S2 = 0.2 µm, S4 = 0.45 µm


WE Series Pleated PolysulfoneMembrane Filter Cartridge

• Composed of a double layer of integrity testable, highly asymmetric polysulfonemembrane. These absolute rated filters offers superior bacteria and particle removal forhigh efficiency postfiltration for critical high purity water applications

• Long on stream life, high flow rates and low pressure drops result from the membrane asymmetry

• High-purity construction materials are factory flushed with DI water for quick on-streamrinse-up with a minimum of throughput

• All polypropylene parts and thermal welding minimizes extractables

• All materials are FDA listed for contact with food and beverages

Clean

Pre

ssure

Dro

p (PS

ID)

2.0

1.5

0.5

1.0

0 .5 1.0 1.5 2.0 2.5 3.0 3.5

0.02µm 0.1µm

0.2µm

0.45µm


BAR

LPM


2 6 128 104


DI Series Pleated Hydrophilic PVDF Media Pharmaceutical/Biotech GradeFilter Cartridge


Diameter (OD) . . . . . . . . . . 2.75" (7.0 cm)Length (in) . . . . . . . . . . . . 10, 20, 30, 40

Materials

Cartridge . . . . . . . . . . . . . . Polypropylene caps, core and cageMedia . . . . . . . . . . . . . . . . Hydrophilic PVDFSeals . . . . . . . . . . . . . . . . . Silicone o-rings and gaskets


Maximum Temperature . . . . . . . . . . . . . . . . . 176°F (80°C) @ 25 psid (1.7 bar)Maximum Differential Pressure @ 25°C. . . . . 50 psi (3.4 bar)Filtration Rating . . . . . . . . . . . . . . . . . . . . . . 100% Absolute


0.1 micron. . . . . . . . . . . . . 0.5 gpm/10" length (1.9 lpm/10" length)0.2 micron. . . . . . . . . . . . . 1.0 gpm/10" length (3.8 lpm/10" length)

Sanitizing Agents


Integrity Test

Pore Size . . . . . . . . . . . Minimum Water Diffusional Flow (cc/min)Bubble Point @ Test Pressure per 10" length

0.1 µm. . . . . . . . . . . . . ≥ 70 psig (≥ 4.8 bar) ≤ 20 @ 56 psig (3.8 bar)0.2 µm. . . . . . . . . . . . . ≥ 45 psig (≥ 3.1 bar) ≤ 12 @ 30 psig (2.1 bar)


FCDI . . . . . . . . . . . . . . . . . Filter cartridge Water DI

X . . . . . . . . . . . . . . . . . . . Cartridge Code: 0 = 2-222 o-rings5 = 2-222 o-rings w/spear7 = 2-226 o-rings w/locking tabs/spear endF = double open end w/flat gasket seal

XX . . . . . . . . . . . . . . . . . . Length (in): 10 = 10, 20 = 20, 30 = 30, 40 = 40

XX . . . . . . . . . . . . . . . . . . Micron Rating: S1 = 0.1 µm, S2 = 0.2 µm


• Composed of a validatable, hydrophilic, PVDF membrane. Offering a high velocity DI water flush for quick rinse-up with no downstream contamination. These absoluterated filters offer superior bacteria and particle removal for critical high puritypostfiltration applications

• Filters have single PVDF membrane with two layers of polypropylene support media to ensure absolute bacteria retention with typical LRV >8

• The all PVDF membrane can be sanitized with chlorine, hydrogen peroxide or steam


• Cartridges are 100% integrity tested to verify absolute sub-micron particle retention

7

6

5

3

1

4

2

00 1 2 3 4 5

0.1 0.2


BAR

LPM


4 12 168

Clean

Pre

ssure

Dro

p (PS

ID)




Materials

Cartridge . . . . . . . . . . . . . . Polypropylene, core and cage, nylon endcapsMedia . . . . . . . . . . . . . . . . PolyethersulphoneSeals . . . . . . . . . . . . . . . . . Silicone o-rings


Maximum Temperature . . . . . . . . . . . . . . . . . 158°F (70°C) @ 25 psid (1.7 bar)Maximum Differential Pressure @ 25°C. . . . . 72 psi (5.0 bar)Filtration Rating . . . . . . . . . . . . . . . . . . . . . . 100% AbsoluteToxicity . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-toxic by USP Class VI Biological test for plasticsValidation . . . . . . . . . . . . . . . . . . . . . . . . . . HIMA Bacterial challenge test methods (107 organisms/cm2)


0.1 µm . . . . . . . . . . . . . . . 0.6 gpm/10" length (2.3 lpm/10" length)0.2 µm . . . . . . . . . . . . . . . 2.0 gpm/10" length (7.6 lpm/10" length)0.45 µm . . . . . . . . . . . . . . 3.0 gpm/10" length (11.4 lpm/10" length)

Sanitizing Agents

Chlorine, hydrogen peroxide, autoclaved for 20 minutes at 121°C under no load conditions.

Integrity Test

Pore Size . . . . . . . . . . . . . . . . . . . Minimum Water Diffusional Flow (cc/min)Bubble Point @ Test Pressure per 10" length

0.1 µm . . . . . . . . . . . . . . . . . . . . ≥ 31 psig ≤ 27 @ 70 psig (4.9 bar)0.2 µm . . . . . . . . . . . . . . . . . . . . ≥ 49 psig ≤ 16 @ 40 psig (2.7 bar)0.45 µm. . . . . . . . . . . . . . . . . . . . ≥ 36 psig ≤ 16 @ 25 psig (1.7 bar)


FCVH . . . . . . . . . . . . . . . . . Filter cartridge pharmaceutical/validated

X . . . . . . . . . . . . . . . . . . . Cartridge Code: 0 = 2-222 o-rings 1 = single open end w/internal o-ring5 = 2-222 o-rings w/spear end7 = 2-226 o-rings w/locking tabs/spear end

XX . . . . . . . . . . . . . . . . . . Length (in): 10 = 10, 20 = 20, 30 = 30, 40 = 40

XX . . . . . . . . . . . . . . . . . . Micron Rating: S1 = 0.1 µm, S2 = 0.2 µm, S4 = 0.45 µm

VH Series Pleated PES Media Pharmaceutical Grade Filter Cartridge

• Cartridge is a validated, pleated polyethersulphone membrane over a non-woven polyester support layer

• Absolute rated

• Code 0, Code 5, Code 7 and Code 10 configurations are available in 10, 20 30, and 40-inlengths that are 100% tested in manufacturing to ensure absolute bacteria retention with typical reduction of >107/cm2

• Meet current USP Class VI biological test for plastics, with a validation certificate available tosupport the bacteria challenge results.

• Contain no surfactants or coatings to interfere with your application, and the thermo-plasticconstruction process minimizes extractables.

• Supported single layer membrane ensures strength, while exhibiting low pressure drop andexceptionally high flow rates

• These validated cartridges can be sterilized by autoclaving

BAR

Clean

Pre

ssure

Dro

p (PS

ID)

2.0

1.5

0.5

1.0

0 .5 1.0 1.5 2.0 2.5 3.0

0.1µm

0.2µm

0.45µm


LPM


2 6 8 104

To figure your order number, replace the X with one of the numbered orlettered options beside it. Note: Not all part number combinations areavailable; consult Technical Support for assistance.


PV Series Pleated Hydrophilic PVDF MediaPharmaceutical Grade Filter Cartridge

• Cartridge is a validated, pleated hydrophilic PVDF membrane over a non-woven polypropylene support layer

• Absolute rated at 0.2 µm

• Code 0, Code 5, and Code 7 configurations are available in 10, 20 30, and 40-in lengthsthat are 100% tested in manufacturing to ensure absolute bacteria retention with typicaltitre reduction of >107/cm2

• Meet current USP Class VI biological test for plastics, with a validation certificateavailable to support the bacteria challenge results.

• Contain no surfactants or coatings to interfere with your application, and the thermo-plasticconstruction process minimizes extractables.

• Supported single layer membrane ensures strength, while exhibiting low pressure drop andexceptionally high flow rates

• These validated cartridges can be sterilized by autoclaving



Materials

Cartridge . . . . . . . . . . . . . . Polypropylene caps, core and cageMedia . . . . . . . . . . . . . . . . PVDFSeals . . . . . . . . . . . . . . . . . Silicone o-rings


Maximum Temperature . . . . . . . . . . . . . . . . . 170°F (80°C) @ 25 psid (1.7 bar)Maximum Differential Pressure @ 25°C. . . . . 80 psi (5.5 bar)Filtration Rating . . . . . . . . . . . . . . . . . . . . . . 100% AbsoluteToxicity . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-toxic by USP Class VI Biological test for plasticsValidation . . . . . . . . . . . . . . . . . . . . . . . . . . HIMA Bacterial challenge test methods (107 organisms/cm2)


0.2 µm . . . . . . . . . . . . . . . 1.0 gpm/10" length (3.8 lpm/10" length)

Sanitizing Agents


Integrity Test

Pore Size . . . . . . . . . . . . . . . . . . . Minimum Water Diffusional Flow (cc/min)Bubble Point @ Test Pressure per 10" length

0.2 µm . . . . . . . . . . . . . . . . . . . . ≥ 45 psig (≥ 3.1 bar) ≤ 13 @ 40 psig (3.1 bar)


FCPV . . . . . . . . . . . . . . . . . Filter cartridge pharmaceutical/validated

X . . . . . . . . . . . . . . . . . . . Cartridge Code: 0 = 2-222 o-rings 5 = 2-222 o-rings w/spear end7 = 2-226 o-rings w/locking tabs/spear end

XX . . . . . . . . . . . . . . . . . . Length (in): 10 = 10, 20 = 20, 30 = 30, 40 = 40

S2 . . . . . . . . . . . . . . . . . . Micron Rating: S2 = 0.2 µm


Clean

Pre

ssure

Dro

p (PS

ID)

Water Flow Rates/10" Cartridge (GPM)

4

8

12

16

FCPV 10S2

FCPV 20S2

FCPV 30S2

FCPV 40S2

20

64 LPM483216

.7

1.4

04 8 12 16 200

BAR



EA Series Hydrophobic Polypropylene Media Vent Filter Cartridge



Materials

Cartridge . . . . . . . . . . . . . . Polypropylene caps, core and cageMedia . . . . . . . . . . . . . . . . Hydrophobic asymmetric polysulfoneSeals . . . . . . . . . . . . . . . . . Silicone o-rings and gaskets


Maximum Temperature . . . . . . . . . . . . . . . . . Ambient AirMaximum Differential Pressure @ 23°C. . . . . 60 psi (4.1 bar)Air Filtration Rating. . . . . . . . . . . . . . . . . . . . 0.02 µm 100% AbsoluteToxicity . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-toxic by USP Class VI Biological test for plastics

Sanitizing Agents

Chlorine, hydrogen peroxide or autoclaving


FCEA . . . . . . . . . . . . . . . . . Filter cartridge vent polysulfone

X . . . . . . . . . . . . . . . . . . . Cartridge Code: 0 = 2-222 o-rings 5 = 2-222 o-rings w/spear end1 = double open end w/internal o-rings7 = 2-226 o-rings w/locking tabs/spear endF = double open end w/flat gasket seal

XX . . . . . . . . . . . . . . . . . . Length (in): 10 = 10, 20 = 20, 30 = 30

S2 . . . . . . . . . . . . . . . . . . Micron Rating: S2 = 0.02 µm (air)

To figure your order number, replace the X with one of the numbered or lettered optionsbeside it. Note: Not all part number combinations are available; consult TechnicalSupport for assistance.NOTE: These filter cartridges should not be used as a combination air vent/wateroverflow device.

• Composed of a pleated hydrophobic highly asymmetric polysulfone membranerated at 0.02 µm absolute for sterile air filtration, storage tank venting applications

• Filter components meet current USP Class VI biological test for plastics

• Contain no surfactants or coatings to interfere with your application, and thethermo-plastic construction process minimizes extractables

• Asymmetric single layer membrane ensures strength, while exhibiting low pressuredrop and exceptionally high flow rates

• Sterilized by autoclaving

Pres

sure

Dro

p (PS

ID)

BAR

2.0

.12

.09

.06

.03

0

1.5

0.5

1.0

0 40

1000 2000 3000 4000

80 120 160Air Flow Rate/10" Cartridge (SCFM)

SLPM

AIR FLOW RATES AT NEAR ATMOSPHERIC PRESSURE (VENT APPLICATIONS)


VP Series Hydrophobic PTFE ValidatedMedia Vent Filter Cartridge

• Composed of a pleated, hydrophobic, PTFE, Teflon membrane rated at 0.2 µm absolute for sterile air filtration, storage tank venting applications

• Filter components meet the criteria of the USP Class VI Biological Test for Plastics

• These filters feature minimal pressure loss, long service life due to high void volume, andcan be repeatedly steam sterilized or autoclaved

• Filters are integrity testable and are fully validated by bacterial challenge (HIMA)



Materials

Cartridge . . . . . . . . . . . . . . Polypropylene caps, core and cageMedia . . . . . . . . . . . . . . . . Hydrophobic Teflon PTFESeals . . . . . . . . . . . . . . . . . Silicone o-rings and gaskets


Maximum Temperature . . . . . . . . Ambient AirMaximum Differential Pressure @ 21°C. . . . . 72 psi (5.0 bar)Air Filtration Rating. . . . . . . . . . . . . . . . . . . . 0.2 µm AbsoluteToxicity . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-toxic by USP Class VI Biological test for plasticsValidation . . . . . . . . . . . . . . . . . . . . . . . . . . HIMA Bacterial challenge test methods (107 organisms/cm2 )

Sanitizing Agents


Integrity Test

Pore Size . . . . . . . . . . . . . . Minimum Water Bubble Point0.2 µm . . . . . . . . . . . . . . . ≥ 14 psig (≥ 1.0 bar) 60 IPA/40 water


FCVP . . . . . . . . . . . . . . . . . Filter cartridge vent polysulfone

X . . . . . . . . . . . . . . . . . . . Cartridge Code: 0 = 2-222 o-rings 5 = 2-222 o-rings w/spear end7 = 2-226 o-rings w/locking tabs/spear end

XX . . . . . . . . . . . . . . . . . . Length (in): 10 = 10, 20 = 20, 30 = 30

S2. . . . . . . . . . . . . . . . . . . Micron Rating: S2 = 0.2 µm

To figure your order number, replace the X with one of the numbered or lettered optionsbeside it. Note: Not all part number combinations are available; consult TechnicalSupport for assistance.NOTE: These filter cartridges should not be used as a combination air vent/wateroverflow device.

Air Flow (SCFM)50 100 150 200

Pres

sure

Dro

p (PS

ID)

2.0

1.5

1.0

0.5

0

10" Cartridge 20" Cartridge

30" Cartridge

1000 2000 3000 4000 5000 6000SLPM


BAR

.12

.09

.06

.03

0


Hydrophobic PTFE Media Vent Capsule Filter

• Composed of a pleated hydrophobic PTFE filter membrane rated at 0.02 µm absolutefor small volume storage tank venting applications

• Convenient threaded inlet, with 1/2" NPTM inlet fitting screws into 1/2" NPTF bulkhead fitting, eliminates the need for a filter housing

• Hydrophobic expanded PTFE membranes are fully validated by bacterial challenge(HIMA)

• Filters feature thermally-bonded polypropylene cage without using adhesives to ensure low extractables

• 100% integrity tested in manufacturing and can be repeatedly autoclaved with steamup to 140°C


Diameter (OD) . . . . . . . . . . 2.2" (5.6 cm)Length (in) . . . . . . . . . . . . 5.9 (15 cm)Inner Connection . . . . . . . . 1⁄2" MNPT

Materials

Cartridge . . . . . . . . . . . . . . Polypropylene Media . . . . . . . . . . . . . . . . PTFE Membrane


Maximum Temperature . . . . . . . . . . . . . . . . . Ambient AirMaximum Differential Pressure @ 23°C. . . . . 60 psi (4.1 bar)Air Filtration Rating. . . . . . . . . . . . . . . . . . . . 0.02 µm 100% AbsoluteToxicity . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-toxic by USP Class VI Biological test for plastics

Sanitizing Agents

Chlorine, Hydrogen Peroxide


FCVPTO6S1 Capsule Hydrophobic PTFE Filter

NOTE: These filter cartridges should not be used as a combination air vent/wateroverflow device.

Pres

sure

Dro

p (PS

ID) 4.0

5.0

3.0

1.0

2.0

8 16 24 32Air Flow (SCFM)

BAR

.35

.28

.21

.07

.14

0

250 500 750 1000SLPM



UF Series Hollow Fiber Polysulfone Media Filter Cartridge



Materials

Cartridge . . . . . . . . . . . . . . Polypropylene caps and cage, polyurethane end sealantMedia . . . . . . . . . . . . . . . . Polysulfone fibersSeals . . . . . . . . . . . . . . . . . Silicone o-rings


Maximum Temperature . . . . . . . . . . . . . . . . . 185°F (85°C) @ 10 psid (.7 bar)Maximum Differential Pressure . . . . . . . . . . . 30 psi (2 bar) @ 25°CFiltration Rating . . . . . . . . . . . . . . . . . . . . . . 100% AbsoluteToxicity . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-toxic by USP Class VI Biological test for plasticsValidation . . . . . . . . . . . . . . . . . . . . . . . . . . Diffusive flow test methods


0.05 micron . . . . . . . . . . . . 2.0 gpm/10" length (7.6 lpm/10" length)0.1 and 0.2 micron. . . . . . . 3.0 gpm/10" length (11.4 lpm/10" length)

Sanitizing Agents

Chlorine, hydrogen peroxide, autoclaved for 20 minutes at 121°C under no load conditions


FCUF . . . . . . . . . . . . . . . . . Filter cartridge ultra filter

X . . . . . . . . . . . . . . . . . . . Cartridge Code: 0 = 2-222 o-rings 5 = 2-222 o-rings w/spear end1 = double open end w/internal o-rings7 = 2-226 o-rings w/locking tabs/spear end

XX . . . . . . . . . . . . . . . . . . Length (in): 10 = 10, 20 = 20, 30 = 30, 40 = 40

XX(X) . . . . . . . . . . . . . . . Micron Rating: S05 = 0.05 µm, S1 = 0.1 µm, S2 = 0.2 µm


• Composed of validatable hollow fiber pleated polysulfone media with polypropylene hardware

• These absolute rated filters offer excellent bacteria and particle and pyrogen removal for critical pharmaceutical and life science applications, at economical costs

• Code 0, Code 5, and Code 7 configurations are available in 10, 20, 30 and 40-inlengths

• Meet current USP Class VI biological test for plastics, with a validation certificate available

• Contain no surfactants or coatings to interfere with your application, and thermo-plastic construction process minimizes extractables

• Hollow fiber construction ensures strength, while exhibiting low pressure drop and exceptionally high flow rates

Clean

Pre

ssure

Dro

p (PS

ID)

BAR


2

4

6

8

10

12

0.5

.1

.10

.20

2 4 6

2 4 6

0


LPM

0.05 µm 0.1 µm

0.2 µm


Point-of-Use High Purity WaterFiltration Capsule Filters

CARTRIDGE SPECIFICATIONSModel Number 500 1000

DimensionsFiltration Area . . . . . . . . . . . . . . . . . 500 cm2 1000 cm2

Diameter (OD) . . . . . . . . . . . . . . . . . 2.7" (6.8 cm) 2.7" (6.8 cm)Length/in (cm). . . . . . . . . . . . . . . . . 4.8" (12.2) 6.7" (16.9)

Materials

Cartridge . . . . . . . . . . . . . Polypropylene caps, core and cageMedia . . . . . . . . . . . . . . . . Pleated polyethersulfone


Maximum Temperature . . . . . . . . . . . . . . . . 140° F (60° C) @ 30 psid (2.1 bar)Maximum Op Pressure . . . . . . . . . . . . . . . . . 60 psid (4.1bar) @ 20° CMaximum Momentary Pressure . . . . . . . . . . . 100 psid (7.0 bar) @ 20° CFiltration Rating . . . . . . . . . . . . . . . . . . . . . . 100% AbsoluteToxicity . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-toxic by USP Class VI Biological test for plasticsValidation . . . . . . . . . . . . . . . . . . . . . . . . . . HIMA Bacterial challenge test methods (107 organisms/cm2)


Model Number 500 10000.1 µm. . . . . . . . . . . . . . . . . . . . 0.04 gpm (0.16 lpm) 0.1 gpm (0.38 lpm)0.2 µm. . . . . . . . . . . . . . . . . . . . 0.1 gpm (0.38 lpm) 0.3 gpm (1.1 lpm)

Integrity TestPore Size: Minimum Water Bubble Point

0.1 µm . . . . . . . . . . . . . . . . . ≥ 90 psig (≥ 6.2 bar) ≥ 90 psig (≥ 6.2 bar)0.2 µm . . . . . . . . . . . . . . . . . ≥ 45 psig (≥ 3.1 bar) ≥ 45 psig (≥ 3.1 bar)

Pore Size: Diffusional Flow (cc/min)0.1 µm . . . . . . . . . . . . . . . . . ≤ 4.0 cc/min at 50 psi (3.4 bar) <6.0 cc/min at 50 psi (3.4 bar)0.2 µm . . . . . . . . . . . . . . . . . ≤ 4.0 cc/min at 40 psi (2.8 bar) <6.0 cc/min at 40 psi (2.8 bar)

Sanitizing Agents

Hydrogen peroxide or autoclaved for 20 minutes at 121°C


FCCF . . . . . . . . . . . . . . . . . Capsule filter

X . . . . . . . . . . . . . . . . . . . Effective filter area: P = 1000 cm2 electronics gradeH = 500 cm2 pharmaceutical gradeE = 500 cm2 electronics grade

X . . . . . . . . . . . . . . . . . . . Inlet fitting: 1 = 1/4" NPTM, 2 = 1/2" NPTM

X . . . . . . . . . . . . . . . . . . . Outlet fitting: 1 = 1/4" hose barb, 2 = 1/4" NPTM, 3 = 1/2" NPTM, 4 = 1/2" hose barb w/filling bell

XX . . . . . . . . . . . . . . . . . . Micron rating: S1 = 0.1µm, S2 = 0.2 µm

• Designed to provide absolute final filtration after laboratory water purification productsor standard service deionization systems

• All polypropylene shell and support materials provide a non-pyrogenic filter, based onUSP and LAL testing

• Microporous membrane is made from hydrophilic polyethersulfone, providing a bacteria retentive filter based on Pseudomonous diminuta challenge (HIMA)

• Integrity tested and validatable, making them ideal for microelectronic andpharmaceutical applications

• Disposable housings are fusion welded without adhesives to ensure low extractables


Pulverized Activated Carbon Filter Cartridge

CARTRIDGE SPECIFICATIONSDimensions 10" Cartridge 20" Cartridge

Diameter (OD) . . . . . . . . . . 2.75" (7.0 cm) 2.75" (7.0 cm)Length (in) . . . . . . . . . . . . 9.75" (24.8 cm) 20" (50.8 cm)


Maximum . . . . . . . . . . . . . 1.0 gpm (3.8 lpm) 2.0 gpm (7.6 lpm)

Materials

Primary filter media . . . . . . . . . . . . . . . . . . . Pulverized, Activated CarbonInner Layer Media . . . . . . . . . . . . . . . . . . . . Alpha Cellulose and Synthetic FibersInner Core . . . . . . . . . . . . . . . . . . . . . . . . . . PolypropyleneOuter Netting . . . . . . . . . . . . . . . . . . . . . . . . PolyolefinEnd Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . Low Durometer Polyethylene


Temperature Range . . . . . . 32 to 125°F (0 – 52°C)

Carbon Volume

3.7 ounces of pulverized carbon per 10" length


FCPC . . . . . . . . . . . . . . . . . Filter cartridge pulverized carbon

F. . . . . . . . . . . . . . . . . . . . Cartridge Code: F = double open end w/flat gasket seal

XX . . . . . . . . . . . . . . . . . . Length (in): 10 = 10, 20 = 20

10. . . . . . . . . . . . . . . . . . . Nominal micron retention rating

To figure your order number, replace the X with one of the numbered orlettered options beside it.

• Composed of pre-washed, finely pulverized activated carbon, encapsulated in a depthfiltration media of highly purified alpha-cellulose and synthetic fibers for removingchlorine

• Depth-type cartridge ensures superior dirt holding capacity in sediment-laden waters to minimize premature exhaustion while it is being carbon treated

• Design includes a thermally bonded outer, nominal 10 micron pre-filtration layer thatprovides for depth filtration in one pass without carbon channeling or media migration


Granular Activated Carbon Filter Cartridge

• Composed of lignite-based granular activated carbon in an upflow cartridge design for removing chlorine feedwaters

• Cartridge is designed to allow water to enter the bottom of the cartridge, then filteredthrough the entire carbon bed before exiting at the top to maximize the contact time andtherefore the adsorption

• Internal expansion pad maintains a tight, compact column to minimize channeling or bypass

• Nominal 20 micron post-filter reduces carbon fines as well as other suspended particles

CARTRIDGE SPECIFICATIONSDimensions 10" Cartridge 20" Cartridge

Diameter (OD) . . . . . . . . . . 2.875" (7.3 cm) 2.875" (7.3 cm)Length (in) . . . . . . . . . . . . 9.75" (24.8 cm) 20" (50.8 cm)


10" Cartridge Maximum . . . 1.0 gpm (3.8 lpm) 2.0 gpm (7.6 lpm)

Materials

Filter Media . . . . . . . . . . . . . . . . . . . . . . . . . Granular, Activated CarbonPost filter. . . . . . . . . . . . . . . . . . . . . . . . . . . Spun PolypropyleneExpansion Pad Foam. . . . . . . . . . . . . . . . . . . Polyther/PolyurethaneOuter Casing . . . . . . . . . . . . . . . . . . . . . . . . PolystyreneEnd Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . PolystyreneGaskets . . . . . . . . . . . . . . . . . . . . . . . . . . . . Buna-N


Temperature Range . . . . . . 32 to 125°F (0 – 52°C)

Carbon Volume

12 ounces of granular carbon per 10" length


FCGC . . . . . . . . . . . . . . . . . Filter cartridge granular carbon

F. . . . . . . . . . . . . . . . . . . . Cartridge Code: F = flat gasket seal

XX . . . . . . . . . . . . . . . . . . Length (in): 10 = 10, 20 = 20

20. . . . . . . . . . . . . . . . . . . Nominal micron retention rating

To figure your order number, replace the X with one of the numbered orlettered options beside it.


316 Stainless Steel, Single-TubeFilter Housing

FILTER HOUSING SPECIFICATIONSDimensions

Length (A) Width (B)

10-in Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5" (34.3 cm) 4.75 (12.1 cm)20-in Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.5" (59.7 cm) 4.75 (12.1 cm)30-in Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.5" (85.1 cm) 4.75 (12.1 cm)

Materials

Bowl and Head. . . . . . . . . . . . . . . . . . . . . . . 316 stainless steelPort Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . 316 stainless steelO-ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethylene Propylene


Max Operating Pressure . . . . . . . . . . . . . . . . 175 psi (12.1 bar) @ 200°F (93°C)Max Housing Flow Rate. . . . . . . . . . . . . . . . . 12 gpm (45.4 lpm)Note: Housing rating only, safe operating pressure will depend on filter cartridge and gaskets used.

Connections

Inlet/Outlet . . . . . . . . . . . . . . . . . . . . . . . . . 3/4" NPTDrain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4" NPT

Mounting

Should be mounted by rigid pipe connections or with optional mounting bracket. Allow enough clearancebelow bottom of housing to allow cartridge to be changed.

Flow Direction

“Inlet” and “Outlet” are cast on the housing head for user convenience.


ZHDFD1001 10" housing



ZHDXDB001 Mounting Bracket

This single-tube cartridge filter housing is made of cast 316 stainless steel and includes 316 stainless steel shell. Housings are available to accommodate 10, 20 or 30-in Code Ffilter cartridges. The inlet and outlet are 3/4" NPT, and the bowl of each housing is fittedwith a 1/4" NPT drain and vent plug. This cartridge filter housing is ideal for a wide varietyof low flow applications requiring a high quality prefilter housing or for applications wherean industrial pre-filter is used.

• Single tube housings accomodate 10", 20" and 30" Code F filter cartridges

• Housing uses 316SS for construction of the head, bowl and port plug

• Inlet and outlet connections are made to the housing head, allowing cartridges to bereplaced without disconnecting the inlet/outlet piping

• Housing can be autoclaved or hot-water sanitized with the cartridges in place for your convenience

Pres

sure

Dro

p (PS

ID)

1614

1012

2

864

0 15105 20 25 30Water Flow Rate (GPM)

HOUSING PRESSURE DROP vs. LIQUID FLOW RATE


316L Stainless Steel, Single-TubeFilter Housing

SYSTEM SPECIFICATIONSDimensions

Length (A) Width (B)10-in Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.8" (37.5 cm) 4.2 (10.5 cm)20-in Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24.8" (62.9 cm) 4.2 (10.5 cm)30-in Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34.8" (88.4 cm) 4.2 (10.5 cm)

Materials

Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316L stainless steelBowl and Plugs. . . . . . . . . . . . . . . . . . . . . . . 316 stainless steelO-ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EPDM

Surface Finish

Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sand Blasted Finish Cartridge Sealing Surface . . . . . . . . . . . . . . . 32 RMS FinishBowl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Satin Finish


Max Inlet Pressure . . . . . . . . . . . . . . . . . . . . 175 psi (12.1 bar) @ 150°F(66°C)Note: Housing rating only, safe operating pressure will depend on filter cartridge and gaskets used.

Connections

Inlet/Outlet . . . . . . . . . . . . . . . . . . . . . . . . . 3/4" NPTDrain and Vent . . . . . . . . . . . . . . . . . . . . . . . 1/4" NPT

Mounting

Should be mounted by rigid pipe connections or optional mounting bracket. Allow enough clearance below bottomof housing to allow cartridge to be changed.

Flow Direction“Inlet” and “Outlet” are electroetched on the housing head for user convenience.


ZHD0D1001 10" housing



ZHDXDB001 Mounting Bracket

This single-tube cartridge filter housing is made of 316L stainless steel and includes 316 stainless steel port plugs. Housings are available to accommodate 10, 20 or 30-in Code 0filter cartridges. The inlet and outlet are 3/4" NPT, and the bowl of each housing is fittedwith a 1/4" NPT drain and vent plug. This cartridge filter housing is ideal for a widevariety of low flow applications requiring a high quality prefilter housing or for applicationswhere an industrial pre-filter is used.

• Inlet and outlet connections are made to the housing head, allowing cartridges to bereplaced without disconnecting the inlet/outlet piping

• Bowl incorporates a satin finish to help prevent bacterial build-up

• Housing can be autoclaved or hot-water sanitized with the cartridges in place for your convenience

• Two vent ports are included in the head for venting, or for the installation of pressuregauges

Pres

sure

Dro

p (PS

ID)

20

15

5

10

0 5 10 15 20 25 30Water Flow Rate (GPM)



304 Stainless Steel, Multi-Tube Filter Housingwith V-Clamp Closure

This multi-tube cartridge filter housing is made of durable 304 stainless steel, and is suitedfor general-purpose industrial and commercial filtration. These housings can accommodate Code F (DOE), Code 0 or Code 5 cartridges.

• Incorporates a flow baffle, which deflects incoming flow to prevent cartridge erosion.

• A 1/4" NPT air vent on the cover allows venting before start-up.

• A 3/4" NPT drain plug allows for liquid removal.

• Cartridges are independently sealed inside the housing and a single V-band clamp housingclosure allows easy cartridge replacement.

• Cartridge post can be lifted out, allowing easy removal of cartridges at the bottom of the stack.

FILTER HOUSING SPECIFICATIONSCartridge Inlet/Outlet Housing Dimensions/Inches (cm) Flange Opt. Max. FlowHousing Inches (cm) A B C D E Rate*/gpm (lpm)

5-round 10" 1-1/2 NPTM (3.8) 25 (64) 11.5 (29) 5.5 (14) 12 (30) 12.75 (32) 25 (94.6)5-round 20" 1-1/2 NPTM (3.8) 32.5 (85) 11.5 (29) 5.5 (14) 12 (30) 12.75 (32) 50 (189)5-round 30" 2 NPTM (5.1) 44 (112) 11.5 (29) 5.5 (14) 12 (30) 12.75 (32) 75 (284)5-round 40" 2 NPTM (5.1) 54.5 (138) 11.5 (29) 5.5 (14) 12 (30) 12.75 (32) 100 (378)

Materials

Head, Shell, Plugs. . . . . . . . . . . . . . . . . . . . . 304 Stainless SteelInternals . . . . . . . . . . . . . . . . . . . . . . . . . . . 316 Stainless SteelCover O-Ring . . . . . . . . . . . . . . . . . . . . . . . . Ethylene PropyleneHold Down Plate Nut. . . . . . . . . . . . . . . . . . . Polypropylene


Maximum Operating Pressure . . . . . . . . . . . . 150 psi (10.7 bar) @ 200°F (93°C)Maximum Housing Flow Rates* . . . . . . . . . . . 100 gpm (378 lpm)

*Housing rating only, cartridge length and type will effect maximum flow rates

ORDERING INFORMATIONCatalog Number Description Inlet/Outlet

ZHFFI0510 5-round 10" 1-1/2” NPT

ZHFFI0520 5-round 20" 1-1/2” NPT

ZHFFI0530 5-round 30" 2” NPT

ZHFFI0540 5-round 40" 2” NPT

ZHFFI0510F 5-round 10" 1-1/2” Flange

ZHFFI0520F 5-round 20" 1-1/2” Flange

ZHFFI0530F 5-round 30" 2” Flange

ZHFFI0540F 5-round 40" 2” Flange

**Flange inlet and outlet are also available; add F Suffix to part number

Outlet

Drain

Nameplate

Tank Assembly

Wing Nut

"Warning" Decal

OptionalFlange

SeparatorSeat Plate

Inlet

O-Ring

Tie Rod

Vent

Cover Assembly

V-ClampNut

Pres

sure

Dro

p (PS

ID)

4.0

2.5

3.0

3.5

2.0

0.5

1.0

1.5

0 20 40 60 80 100 120 140Water Flow Rate (GPM)

1.5" Connection

2" Connection



304 Stainless Steel, Multi-TubeFilter Housing with Swing Bolt Closure

This multi-tube cartridge filter housing is made of 18 gauge 304 stainless steel. Housingsare available to accommodate six, 10, 20, 30 or 40-in, Code F filter cartridges. The inletand outlet are 2" NPT. There is a 1/2" NPT drain plug, and a 1/4" NPT vent at the topof the housing. A swing bolt closure allows quick disassembly for cleaning and service.This cartridge filter housing is ideal for a wide variety of high flow applications thatrequire an economical, high quality housing.

• Uses 304 stainless steel construction for maximum corrosion resistance to deliver years of dependable service

• A swing bolt closure allows quick disassembly for cleaning and service

• An air vent plug on the cover allows venting before start-up

• This housing accommodates liquid flow rates up to 180 gpm (681 Lpm) with operating pressures to 150 psig (10.3 bar)

FILTER HOUSING SPECIFICATIONSCartridge Housing Dimensions/Inches (cm) Flange Option Max. FlowHousing A B C D E Rate*/gpm (lpm)

6-round 10" 24 (61) 11.2 (28) 5.2 (13) 10.2 (26) 15 (38) 30 (114)6-round 20" 34 (86) 11.2 (28) 5.2 (13) 10.2 (26) 15 (38) 60 (227)6-round 30" 45 (114) 11.2 (28) 5.2 (13) 10.2 (26) 15 (38) 90 (340)6-round 40" 56 (142) 11.2 (28) 5.2 (13) 10.2 (26) 15 (38) 120 (454)

Materials

Head and Shell . . . . . . . . . . . . . . . . . . . . . . . 304 Stainless SteelVent and Drain Plug . . . . . . . . . . . . . . . . . . . 304 Stainless Steel Seat Cups. . . . . . . . . . . . . . . . . . . . . . . . . . . 316L Stainless SteelO-Ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethylene Propylene


Maximum Operating Pressure . . . . . . . . . . . . 150 psi (10.3 bar) @ 200°F (93°C)Max Water Flow Rate* . . . . . . . . . . . . . . . . . 120 gpm (454 Lpm)



ZHGAF0610 6-round 10" 2" NPT




ZHGAF0610F 6-round 10" 2" flange




120.

00

Vent

Head

O-ring

Outlet

InletDrain

SpacerCartridge

ShellTube Guide

Bottom Seat Plate

CompressionSeat Plate Assembly

Swing Bolt Assembly

A

D

E

B

C

120.

00

Pres

sure

Dro

p (PS

ID)

10.0

8.0

6.0

2.0

4.0




316 Stainless Steel, Multi-Tube Filter Housing

This multi-tube cartridge filter housing ismade of 316 stainless steel, and is suited forgeneral-purpose industrial and commercialfiltration. These housings can accommodateCode F (DOE) cartridges, and are availablewith 6, 12, and 21 tubes in 10, 20, 30, 40-inch lengths.

• Incorporates a flow baffle, which deflectsincoming flow to prevent cartridge erosion.

• An air vent on the cover allows ventingbefore start-up.

• A swing boot closure allows quick disassembly for cleaning and cartridge replacement

FILTER HOUSING SPECIFICATIONSDimensions Inlet/Outlet Housing Dimensions Flange Option Max. Flow(inches (cm) A B C D E Rate*/gpm (lpm)

6-round 10” 2 NPTM (5.1) 24 (61) 11.2 (28) 5.2 (13) 10.2 (26) 15 (38) 30 (114)6-round 20” 2 NPTM (5.1) 34 (86) 11.2 (28) 5.2 (13) 10.2 (26) 15 (38) 60 (227)6-round 30” 2 NPTM (5.1) 45 (114) 11.2 (28) 5.2 (13) 10.2 (26) 15 (38) 90 (340)6-round 40” 2 NPTM (5.1) 56 (142) 11.2 (28) 5.2 (13) 10.2 (26) 15 (38) 120 (454)12-round 30” 3 flange (7.6) 56 (142) 31 (79) 12 (30) 12 (30) 16.4 (42) 180 (680)12-round 40” 3 flange (7.6) 66 (168) 31 (79) 12 (30) 12 (30) 16.4 (42) 240 (908)21-round 30” 4 flange (10.16) 57 (145) 31 (79) 12 (30) 16 (41) 20.8 (53) 315 (1190)21-round 40” 4 flange (10.16) 67 (170) 31 (79) 12 (30) 16 (41) 20.8 (53) 420 (1560)

Materials

Head, Shell, Plugs . . . . . . 316L Stainless SteelInternals . . . . . . . . . . . . 316 Stainless SteelCover O-Ring . . . . . . . . . EDPM

Maximum Operating Pressure

6-Round. . . . . . . . . . . . . 150 psi (10.3 bar) @ 200°C (93°F)12-Round. . . . . . . . . . . . 150 psi (10.3 bar) @ 200°C (93°F)21-Round. . . . . . . . . . . . 150 psi (10.3 bar) @ 200°C (93°F)


ZHGOF610 6-round 10" 2" NPT




ZHGOF610F 6-round 10" 2" flange




ZHFFI1230 12-round 30" 3" flange





Pres

sure

Dro

p (PS

ID)

10

8

6

2

4

0 100 200 300 400Water Flow Rate (GPM)

12-round

21-round


Pres

sure

Dro

p (PS

ID)

10.0

8.0

6.0

2.0

4.0



120.

00

Vent

Head

O-ring

Outlet

InletDrain

SpacerCartridge

ShellTube Guide

Bottom Seat Plate

CompressionSeat Plate Assembly

Swing Bolt Assembly

A

D

E

B

C

120.

00

6-ROUND DIMENSIONS

12- AND 21-ROUND DIMENSIONS


316L Electropolished Stainless Steel,Multi-Tube Filter Housing

This multi-tube cartridge filter housing is made of electropolished 316L stainless steel.Different housings are available to accommodate seven 10, 20, 30 of 40 inch, Code 5 orCode 0 filter cartridges with two 222 O-rings. The inlet and outlet are 2" NPTM, or optional2" flange, and the bottom of each housing is fitted with a 3/4" NPTF drain plug. A V-bandclamp closure allows cartridges to be changed quickly and easily. This cartridge filter housingis ideal for a wide variety of low flow applications requiring an economical yet high qualityprefilter housing or for applications where industrial membrane filtration is used.

• Housing uses electro-polished 316L stainless steel construction that is easy to clean and provides maximum corrosion resistance

• Predrilled support stand allows the housing to be secured to floor or some mounting surface

• Housing can also accommodate Code F (DOE) cartridges, with liquid flow rates of 150 gpm, and operating pressures to 150 psig

• A 1/4" NPTF air vent plug on the cover allows venting before start-up

FILTER HOUSING SPECIFICATIONSDimensions Inlet/Outlet Housing Dimensions Flange Option Max. Flow(inches (cm) A B C D E Rate*/gpm (lpm)

7-round 10" 2" NPTM (5.1) 25 (64) 11.5 (29) 5.5 (14) 12 (30) 12.8" (32) 35 (132)7-round 20" 2" NPTM (5.1) 33.5 (85) 11.5 (29) 5.5 (14) 12 (30) 12.8" (32) 70 (264)7-round 30" 2" NPTM (5.1) 44 (112) 11.5 (29) 5.5 (14) 12 (30) 12.8" (32) 105 (398)7-round 40" 2" NPTM (5.1) 54.5 (138) 11.5 (29) 5.5 (14) 12 (30) 12.8" (32) 140 (530)

Materials

Head and Shell . . . . . . . . . . . . . . . . . . . . . . . 316L Stainless Steel electropolishedVent and Drain Plug . . . . . . . . . . . . . . . . . . . 316 Stainless Steel Seat Cups. . . . . . . . . . . . . . . . . . . . . . . . . . . 316L Stainless SteelO-Ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethylene Propylene


Maximum Operating Pressure . . . . . . . . . . . . 150 psi (10.3 bar) @ 93°F (200°C)Maximum Water Flow Rate* . . . . . . . . . . . . . 140 gpm (528 Lpm)



ZHH000710 7-round 10" 2" NPTM




ZHH000710F 7-round 10" 2" flange




Vent

Cover AssemblyTie Rod

Nut

O-Ring

Inlet

SeparatorSeat Plate

V-Clamp

Wing Nut

Tank Assembly

Nameplate

"Warning" Decal

Drain

Outlet

Pres

sure

Dro

p (PS

ID)

12

8

10

6

2

4

0 30 60 90 120 150 180 210Water Flow Rate (GPM)



Plastic Filter Housings

FILTER HOUSING SPECIFICATIONSDimensions 10" Cartridge 20" Cartridge

Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2" (13.2 cm) 5.2" (13.2 cm)Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2" (31 cm) 22.4" (57 cm)


Maximum . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 gpm (30 lpm) 16 gpm (60 lpm)

Materials

Polypropylene cap and housing with standard BUNA-N o-rings


Maximum Operating Pressure . . . . . . . . . . . . . . . . . 125 psi (8.6 bar)Maximum Operating Temperature . . . . . . . . . . . . . . 100°F (38°C)Sterilization/Sanitization Hydrogen Peroxide . . . . . . . 7.5% compatibility; static soak up to 24 hr at ambient temperature

Weight

10" housing . . . . . . . . . . . . . . . . . . . . . . . . . 3 lb (1.4 kg)20" housing . . . . . . . . . . . . . . . . . . . . . . . . . 4.25 lb (1.9 kg)

Housing Compatibility/Cartridge Type

ZHCFA1001 . . . . . . . . . . . . . . . . . . . . . . . . . Code F, 9-3/4”ZHCFA2001 . . . . . . . . . . . . . . . . . . . . . . . . . Code F, 20”


ZHC Polypropylene filter housing

F Cartridge Code: F = Code F

A A = No plugs

XX Length (in): 10 = 10, 20 = 20

01 01 = 1 tube

ACCESSORIESCatalog Number and Description

ZHA150060 Mounting Bracket

These filter housings are molded from polypropylene, and are available in 10- and 20-inch lengths. Housings are supplied with 3/4" inlet and outlets in standard flat gasketdesign for Code F filter cartridges.

• Durable housings are made from all polypropylene materials

• Housings are autoclavable, ETO sterilizable, and hydrogen peroxide compatible

• Supplied with 3/4" NPT inlet and outlets in standard flat gasket design for Code Ffilter cartridges


FILTER HOUSING SPECIFICATIONSDimensions 10" Cartridge 20" Cartridge

Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2" (13.2 cm) 5.2" (13.2 cm)Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2" (31 cm) 22.4" (57 cm)

Recommended Water Flow Rates 10" Cartridge 20" Cartridge

Maximum (Code 0 cartridge). . . . . . . . . . . . . . 4 gpm (15 lpm) 6 gpm (22.7 lpm)

Materials

Natural polypropylene cap and housing with standard Viton E-60 o-rings


Maximum Operating Pressure . . . . . . . . . . . . 100 psi (6.9 bar)Maximum Operating Temperature . . . . . . . . . 100°F (38°C)Sterilization/Sanitization

Autoclavable . . . . . . . . . . . . . . . . . . . . . 25 min 121–127°C (252–260°F)Hydrogen Peroxide . . . . . . . . . . . . . . . . 7.5% compatibility; static soak up to 24 hr at ambient temperature

Weight

10" housing . . . . . . . . . . . . . . . . . . . . . . . . . 3 lb (1.4 kg)12" housing . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 lb (1.6 kg)20" housing . . . . . . . . . . . . . . . . . . . . . . . . . 4.25 lb (1.9 kg)

Housing Compatibility/Cartridge Type

ZHA0D1201* . . . . . . . . . . . . . . . . . . . . . . . . Code 0, 10"ZHA0D2001. . . . . . . . . . . . . . . . . . . . . . . . . Code 0, 20"ZHAFD1001 . . . . . . . . . . . . . . . . . . . . . . . . . Code F, 93⁄4"ZHAFD2001 . . . . . . . . . . . . . . . . . . . . . . . . . Code F, 20"

*Code 0, 10" cartridge must be used with 12" housing

ORDERING INFORMATION ACCESSORIESCatalog Number and Description Catalog Number and Description

ZHA Natural polypropylene filter housing ZHA150060 Mounting Bracket

X Cartridge Code: F = Code F, 0 = Code 0

D Cartridge Configuration: D = Double cap plug

XX Length: 10 = 10, 12 = 12, 20 = 20

01 Number of Tubes: 01 = 1 tube

To figure your order number, replace the X with one of the numbered/lettered options below it.

Natural Polypropylene Filter Housing

These filter housings are molded from natural, high-density polypropylene, and are availablein 10-, 12- and 20-inch lengths. Housings are molded in dies that are minutely polished foran ultra-smooth finish to all contact surfaces, thus minimizing the opportunity for bacteriaadhesion. Housings are supplied with 3/4" inlet and outlets in standard flat gasket design forCode F filter cartridges, and 222 O-ring design for Code 0 filter cartridges. Heads areavailable with double cap plug design and viton O-rings.

• Durable housings are made from all polypropylene materials (except for O-rings)

• Housings contain no fillers, colorants, plasticizers, or lubricants

• Available in flat gasket design for Code F filter cartridges, and 222 O-ring design for Code 0 filter cartridges

• Housings are autoclavable and hydrogen peroxide compatible

• Supplied with 3/4" NPT inlet and outlets

A Total Solution from One Supplier: The USFilter Difference

USFIlter understands how important it is for your water treatment

equipment to operate reliably and economically. That’s why we offer

a wide range of high-quality, economical aftermarket products and

services worldwide to meet your needs. We help you stay ahead with

our full selection of products and services. From replacement parts to

upgrading an existing system, we provide total solutions to help

you manage your most challenging projects.

SERVICE DEIONIZATION (SDI)

WATER ANALYSIS/RESIN ANALYSIS

MAINTENANCE CONTRACTS

RESIN REGENERATION

MOBILE TREATMENT SYSTEMS

MEMBRANE CLEANING

WASTEWATER SERVICES

COMPLETE WATER SYSTEMS

LABORATORY SYSTEMS

ION EXCHANGE RESIN

REPLACEMENT PARTS

FILTER CARTRIDGES

FILTRATION MEDIA

RO MEMBRANES

OUR AFTERMARKET SERVICES AND PRODUCTS

Your USFilter sales representative is your single contact for any

components you require for your facility. In addition, that same

representative can arrange to have maintenance technicians

dispatched from one of our many local branches, should your system

ever require service.

North America Customer & Technical Service NetworkIn the Continental United States

800.466.7873 Customer Service 24-hour800.875.7873 ext. 5000 Technical Support

10 Technology DriveLowell, MA 01851

In CanadaUSFilter Canada East (Toronto)

905.890.2803 Customer Service 24-hour

USFilter Canada West (Calgary)403.250.2650 Customer Service 24-hour

or contact your local USFilter branch

http://www.usfilter.com©2001 USFilter

USFilter is ready to serve you quickly and efficiently with over 70

service centers and 5 distribution and regeneration plants nationwide.

In accordance with USFilter policy for continualproduct development and improvement, wereserve the right to change the productspecification within this literature at any time,without notice. USFilter, CDI®, are registeredtrademarks of United States Filter Corporation or an affiliated company.

Printed on recylced paper in the U.S.A. 2/01

Literature No.: LO-AF-CA-0101

cartridge filter cartridge

Documents