cable laying & equipment...cable rollers 15 conduit cable guides 16 cable lubricant 19 hauling...

1800 328 200 | www.legend.com.au | [email protected]

Cable Laying & Equipment

ContentsContents

Pulling Tools 3

Conduit Rods and Frames 7

Gas Tools 8

Drum Stands 13

Cable Rollers 15

Conduit Cable Guides 16

Cable Lubricant 19

Hauling Rope 20

Cable Blowers 20

Line Carriers 21

Cleaners and Mandrels 22

Hauling Swivels 23

Line Tensioners 27

Cable Stocking 28

Cable Pullers 32

Manhole Equipment 33

Pit Keys and Breaker 34

Index 36

GENERAL LINE EQUIPMENT

3

MSP Conduit Rod KitsThe MSS range of fibreglass rods have a copper trace wire running through the core making them suitable for underground cable & conduit locating, with the use of a suitable locator. The rod is supplied complete with brass male ends & hauling eye, and fitted to a sturdy zinc plated steel frame with brake. Optional re-fills are available as well as flex ends and joining kits.

4.5mm 6mm 9mm 11mm

• Highly flexible wire springs with a steel wire reinforcement through the middle• Ideal for ‘fishing’ in conduits and ducting• For smaller direct pulls or attach a pull line in larger pulls

CABAC PULL THROUGH SPRINGS

Part No. Min. Breaking Strain (kg) Length (mm) Unit Qty

PTS20M 100 20 EA 1

PTS30M 100 30 EA 1

PULLING TOOLS

Part No. P802163 • Triple stranded cable pulling device• Non-conducting coiled spring leader• Material: Polyester Wire• Available in 30m and 60m lengths

CROMASNAKE FIBREGLASS CABLE SNAKE 30MCROMA CABLE SNAKES

Unit: EA Qty: 1

Part No. P802164 • Triple stranded cable pulling device• Non-conducting coiled spring leader• Material: Polyester Wire• Available in 30m and 60m lengths

CROMASNAKE FIBREGLASS 5MMCABLE SNAKE 60M Unit: EA Qty: 1


4

Part No. FTCM30 • Top end professional fish tape made from pull-truded glass with special polypropylene outer coating - low friction and high abrasion

resistance• Non-conductive glass increases safety• Resilient to bending and shear stresses• Can be repaired if broken using repair kit (Part No. FTRC)

CABLEMASTER - FIBREGLASS FISH TAPE 30MCABAC FISH TAPES

Unit: EA Qty: 1

Part No. FTGJ20 • Top end professional fish tape made from pull-truded glass with special polypropylene outer coating - low friction and high abrasion

resistance• Non-conductive glass increases safety• Highly resilient to bending and shear stresses• Supplied in a tubular casing with a shoulder strap

GLASSJACK - FIBREGLASS FISH TAPE 20M Unit: EA Qty: 1

Part No. FTR6 • Set of flexible cable pulling rods which connect together to form a pulling rod up to 6m in length• Suitable for installing wiring and light cables into a roof• Supplied in a sturdy transparent plastic packing tube• Rods from another set may be added to make an even longer pulling

CABLEPR PUSH PULL CABLE ROD SET Unit: EA Qty: 1

Part No. FTRC • Suitable for use with CABLEMASTER fish tape• Accessories include PULLGRIP cable stocking and FLEXIGRIP• Repair items include rod ends, splices and special adhesive

FISH TAPE ACCESSORIES AND REPAIR KITCABAC FISH TAPE REPAIR KITS

Unit: EA Qty: 1


5

Part No. MSS-GCG30V • Fitted to a sturdy plastic wheel suitable for both left and right handed users• Supplied with various end attachments• Rod repair kit stored neatly in the centre of the dispenser• Comes with 1 x lubrication spray bottle

MINI ROD - 3MM X 30MTR Unit: EA Qty: 1

Part No. MSS-THR-223M • A lighter, stronger and more flexible hand rod• Made from Polycarbonate• Fitted with brass ends• Supplied in 22mm x 3m lengths

WHITE HAND ROD-3MTR X 22MM Unit: EA Qty: 1

Part No. MSS-TCH-22MF • Connects on to the end of a 22mm hand rod to assist twisting the rod in a clockwise direction

CRANK HANDLE FOR 22MM HAND RODS Unit: EA Qty: 1

Part No. MSS-TFL-22 • Suits a 22mm hand rod

FLEXIBLE LEADER FOR 22MM HAND RODS Unit: EA Qty: 1


6

Part No. MSS-THL-2290 • For linking hand rod in conduit• Suits a 22mm hand rod

HOOK & LOOP SET TO SUIT 22MM HAND RODS Unit: EA Qty: 1

Part No. MSS-TRE-22 • Suits a 22mm hand rod

LEAD IN EYE FOR 22MM HAND RODS Unit: EA Qty: 1


7

• Flexible spring leader to suit a 4.5mm rod• 6, 9 & 11mm rod flexible springs leaders also available

MSP CONDUIT KIT FITTINGS

Part No. Description Unit Qty

MSS-4.5FLEX FLEXY END FITTING - 4.5MM ROD EA 1

MSS-6FLEX FLEXY END - 6MM O/D ROD EA 1

MSS-9FLEX FLEXY END FITTING - 9MM ROD EA 1

MSS-11FLEX FLEXY END FITTING - 11MM ROD EA 1

CONDUIT RODS AND FRAMES

• Suitable for underground cables and conduit locating with the use of a suitable locator• Supplied complete with brass ends and hauling eye• Copper trace wire running through the core• Fitted to a sturdy zinc plated steel frame with brake

MSP CONDUIT ROD KITS


MSS-4.5-30 4.5MM X 30 MTR TRACE ROD AND FRAME KIT 1

MSS-4.5-60 4.5MM X 60MTR TRACE ROD AND FRAME KIT 1



MSS-6TR-60 6MM X 60MTR TRACEROD AND FRAME KIT 1




MSS-6TR-150 6MM X 150MTR TRACEROD AND FRAME EA 1

MSS-6TR-200 6MM X 200MTR TRACEROD AND FRAME EA 1





MSS-9TR-250 9MM X 250MTR TRACE ROD AND FRAME KIT 1









8

• Suitable for underground cables and conduit locating with the use of a suitable locator• Refill for rod and frame• Copper trace wire running through the core• Various lengths and diametres available• Comes with brass frame attachment & hauling eye

MSP REFILL COILS


MSS-RFL-4.5-30 REFILL COIL - 4.5MM TRACE ROD X 30MTR EA 1

MSS-RFL-4.5-60 REFILL COIL - 4.5MM TRACE ROD X 60MTR KIT 1

MSS-RFL-4.5-80 REFILL COIL - 4.5MM TRACE ROD X 80MTR KIT 1

MSS-RFL-6-60TR REFILL COIL - 6MM TRACE ROD X 60MTR EA 1

MSS-RFL-6-80TR REFILL COIL - 6MM TRACE ROD X 80MTR KIT 1
















• Repair/joining kit for our range of MSS Power conduit rods• Includes rod joiners, male ends, hauling eyes and glue packs

MSP REPAIR KITS


MSS-JK4.5-3.0 JOINING KIT FOR 4.5MM OD TRACE ROD EA 1

MSS-JK6.5-4.5 JOINING KIT FOR 6MM OD TRACE ROD EA 1



Part No. MSS-TEL414-82 • 3/8 BSP Ends to Suit other Gas Accessories• Accurate and Quick Flame Setting

GAS HAND PIECEMSP GAS TOOLS

GAS TOOLS

Unit: EA Qty: 1


9

Part No. MSS-TEL414-130 • 3/8 BSP Ends to Suit other Gas Accessories• Strong windproof flame

SOFT FLAME BURNER Unit: EA Qty: 1

Part No. MSS-TEL414-77 • 3/8 BSP Ends to Suit Other Gas Accessories

HARD FLAME BURNER Unit: EA Qty: 1

Part No. MSS-TEL414-84 • 3/8BSP ends to suit other gas accessories• Regulator has leak test and hose failure system

LEAK TEST REGULATOR Unit: EA Qty: 1

Part No. MSS-TEL414-105 • 3/8 BSP Ends to Suit Other Gas Accessories• 6m• 2m hose set available p/n MSS-TEL414-71

6MTR HOSE SET GAS Unit: EA Qty: 1

Part No. MSS-TEL414-50 • Telstra Approved gas cylinder• 3/8BSP ends to suit other gas accessories• 1.25kg slimline refillable cylinder• 3kg and 9kg gas cylinders available

1.25KG GAS CYLINDER Unit: EA Qty: 1


10

Part No. MSS-SV3366 • Automatic ignition - guaranteed for 30,000 ignitions• Trigger on/off function - no waste of LP gas• Precise flame adjustment valve• Ergonomic and modern design

HANDLE BLOW TORCH PROMATIC 3366 Unit: EA Qty: 1

Part No. MSS-TX405C • Creates spark to ignite gas burners• Supplied with 2x replacement flints• Ignites most propane and MAPP gas fuelled appliances

CUP STYLE FLINT LIGHTER Unit: EA Qty: 1

Part No. MSS-306311 • Suits 9kg gas cylinder

GAS REG W/HOSE FAIL VALVE POL CONN. Unit: EA Qty: 1

Part No. MSS-100505001 • Used in busy communication pits to protect neighbouring cable whilst heatshrinking• Small and flexible• Made from flame retardant material

JOINTERS HEATSHIELD - 30 X 30CM Unit: EA Qty: 1


11

Part No. 45-235 • Self-adjusting stripping blades automatically select proper position• Strips 12 AWG solid to 14 AWG Underground Feeder (UF) Cable• Strips twin and earth cable• Neatly removes outer cable sheath and then inner wire sheathing• Strips twin and earth cable

IDEAL UNDERGROUND FEEDER CABLE STRIPPERIDEAL GAS TOOLS

Unit: EA Qty: 1

• 60/40 Resin Cored High Quality Solder 500g• Tin/Lead, Low Melting Point Solder• Conforms BSS 441 DTD 599A• Max 0.5% Halide

ECCO GAS TOOLS


P611007 0.56 MM 60/40 SOLDER 500G REEL EA 1

P611005 0.71MM 60/40 SOLDER 500G 20SWG EA 1

P611003 0.91MM 60/40 SOLDER 500G REEL EA 1




P611009 3.2MM SOLDER 60/40 500G REEL EA 1

UNDERGROUND CABLE HANDLING

12

Scissor Type Cable Drum JacksThe Scissor lift drum stands are well suited for uneven ground as the individual lifting screws can be adjusted separately.

They are simple and easy to use and utilise sealed directional bearings (insert) for ease of lifting and lowering of cable drums.

Complete with two stands with wheels for transportation, collars to retain drums and a ground joining bar for rigidity during operation. Along with a stamped and registered load bearing axle, the SLS is a very cost effective and efficient set of equipment.

Features:• Made in Australia• Manoeuvrable and Transportable• Designed for Rugged Use• Winding via Spin Handle or with a 25mm Ratchet

Wrench• Fitted with Wheels for Ease of Placement• Suitable for Lifting Cable Drums up to 4 tonneALSO AVAILABLE:Part No. MSS-SLS1-2TScissor Drum Jack Set - Suitable for lifting cabledrums up to 2 tonne.

Directional Bearings

SUITABLEFOR CABLE

DRUMSUP TO

4 TONNE

Optional Accessories:Part No. MSS-DB-400 Disc brake and fixing arm set to suit 40mm dia axle

Part No. MSS-DB-630 Disc brake and fixing arm set to suit 63mm dia axle



Hydraulic Cable Drum JacksCable drum jacks are used for holding or lifting cable drums off the ground so they can be uncoiled for installation of underground power cables, conductors, wire, coaxial cable, etc. The cable drum is moved, rolled or lifted into position and then jacked up using an integrated hydraulic jack or screw jack system.

Optional accessories available are a disc brake and a fixing arm. These two items have been specially designed to complement the Hydraulic Cable Drum Jack to deliver further versatility and usability.

Image shows optional Disc brake feature.

SUITABLEFOR CABLE

DRUMSUP TO

8 TONNE

Manoeuverable and Transportable

Part No. MSS-DJS-58T

Part No. MSS-SLS3-4T


13

Part No. MSS-CRS350 • Quality construction cable reel dispenser• Suits 2 to 3 reels of electrical cable• Maximum 650mm OD drum

CABLE REEL STAND - MAX 650MM OD DRUMMSP DRUM STANDS

DRUM STANDS

Unit: EA Qty: 1

Part No. MSS-CDT-500 • Quality construction cable drum trolley• Suits a 90cm wide x 1m diameter drum• Holds drum up to 500kg

CABLE DRUM TROLLEY TO SUIT UPTO 500KG Unit: EA Qty: 1

Part No. MSS-SLS-05T • Suitable for lifting cable drums up to 500kg’s• Fully collapsible for easy transportation• Set up in minutes

SCISSOR DRUM JACK SET-UP TO 500KG Unit: EA Qty: 1

Part No. MSS-SLS1-2T • Suitable for lifting cable drums up to 2 tonne• Fully collapsible for easy transportation• Set up in minutes• Comes with a 60mm OD axle• Comes with 2 x drum retaining collars

SCISSOR DRUM JACK SET - UP TO 2 TON Unit: EA Qty: 1

Part No. MSS-SLS3-4T • Suitable for lifting cable drums up to 4 tonne• Fully collapsible for easy transportation• Set up in minutes• Comes with a 90mm OD axle• Comes with 2 x drum retaining collars

SCISSOR DRUM JACK SET - UP TO 4 TON Unit: EA Qty: 1


14

Part No. MSS-DJS-58T • Works with the use of bottle jacks fitted to the base to lift the drum off the ground• Suitable for drums up to 8 tonne• Optional disc brake feature

HYDRAULIC DRUM JACK SET 8T WWL MAX Unit: EA Qty: 1

Part No. MSS-DRR-1000 • For use with drum diameters up to 1.5m• Safe Work Load of 1000kg (per set)• Fold away for easy storage

DRUM RAMP ROLLER SET 1000KG Unit: EA Qty: 1

Part No. MSS-4JZ-DZ255S • 1000kg drum capacity• 400-1200mm drum OD capacity• Heavy Duty• Comes with Joiner Bar

DRUM RAMP ROLLERS-1T-40-1120CM Unit: EA Qty: 1

• Accessory for the MSS-DJS-58T Hydraulic Cable Drum Jack• Suits 40mm diameter axle• Other sizes also available

DISC BRAKE AND FIXING ARMS


MSS-DB-400 DISC BRAKE & FIXING ARM SUITS 40MM AXLE EA 1


MSS-DB-660 DISC BRAKE/FIXING ARM- SUIT 66MM OD AXLE EA 1



15

Part No. MSS-NTR-120 • Economy trench roller with flat base - 120mm wide plastic roller• Single plastic roller• Zinc plated frame• 500kg WLL

FLAT TRENCH ROLLER - PLASTIC ROLLERMSP CABLE ROLLERS

CABLE ROLLERS

Unit: EA Qty: 1

Part No. MSS-NTRA-120 • Trench roller with flat base - 120mm wide aluminium roller• Single Aluminium roller• Zinc plated frame• 1000kg WLL

FLAT TRENCH ROLLER - ALUMINIUM ROLLER Unit: EA Qty: 1

Part No. MSS-RTR-140 • Economy raised trench roller - 140mm wide plastic roller• Single plastic roller• Zinc plated frame• 500kg WLL

RAISED TRENCH ROLLER - 140MM PLASTIC Unit: EA Qty: 1

Part No. MSS-RTRA-140 • Raised trench roller raised -140mm wide aluminium roller• Single Aluminium roller• Zinc plated frame• 1000kg WLL

RAISED TRENCH ROLLER - 140MM Unit: EA Qty: 1

Part No. MSS-TCR-200 • Trench corner roller, used to create a 90 degree bend• optional star picket available p/n MSS-SCR-600

TRENCH CORNER ROLLER Unit: EA Qty: 1


16

Part No. MSS-TRGM-100 • Above ground to conduit transition cable guide - 125mm OD cable max• Single Aluminium roller• Zinc plated frame

MANHOLE GUIDE - SINGLE ROLLER Unit: EA Qty: 1

Part No. MSS-TRGM-100-2 • Above ground to conduit transition cable guide - 125mm OD cable max• Two Aluminium rollers• Zinc plated frame

MANHOLE GUIDE - TWIN ROLLER Unit: EA Qty: 1

Part No. MSS-TRGM-100-3 • Above ground to conduit transition cable guide - 125mm OD cable max• Three Aluminium rollers• Zinc plated frame

MANHOLE GUIDE - TRIPLE ROLLER Unit: EA Qty: 1

• Chrone Zinc Plated Finish• Uses a ‘bell mouth’ to aid the entering and exit of cables• Lockable inside conduit

MSP INLINE FEEDING SHEAVES


MSS-IFS-080 INLINE FEEDING SHEAVE FOR 80MM CONDUIT EA 1

MSS-IFS-100 INLINE FEEDING SHEAVE 100MM CONDUIT EA 1

MSS-IFS-125 INLINE FEEDING SHEAVE 125MM CONDUIT EA 1

MSS-IFS-150 INLINE FEEDING SHEAVE FOR 150MM CONDUIT EA 1

CONDUIT CABLE GUIDES


17

• Provides a smooth surface for the cable to glide easily against• Various sizes available - up to 150mm

MSP CONDUIT SLIPPER GUIDE


MSS-CCG-028 CONDUIT SLIPPER GUIDE 28MM EA 1







• Locks to the inside of the conduit to provide a smooth, stable surface for cable to glide easily• Various sizes available

MSP LOCKABLE CABLE SLIPPER GUIDES


MSS-CLS-050 LOCKABLE CONDUIT SLIPPER GUIDE 50MM EA 1



MSS-CLS-125 LOCKABLE CONDUIT GUIDE 125MM EA 1

MSS-CLS-150 LOCKABLE CONDUIT GUIDE 150MM EA 1

• Suitable for use in electrical and telecommunication conduit• Cast Aluminium bell mouth guides assist in protecting cable• Various sizes available

MSP BELLMOUTH CABLE GUIDES


MSS-BM100 BELLMOUTH CONDUIT GUIDE - 100MM EA 1



Part No. MSS-PMCG-100 • Above ground to conduit transition cable guide - 100mm OD cable max• Pivoting slipper guide for cable protection• Zinc plated

PIVOTING GUIDE 100MMMSP PIVOT GUIDES

Unit: EA Qty: 1


18

Part No. MSS-PMRG-140 • 3x 140mm rollers• Pivoting guide with 3 rollers for protection of large UG cable• Aluminium rollers - zinc plated frame

PIVOTING GUIDE WITH 3 X 140 ROLLERS Unit: EA Qty: 1

Part No. MSS-FS-050 • To suit 50mm Telstra conduit• Min 46mm adjustable split lock OD• Full ball bearing roller guide• Chrome zinc plated finish

LOCKABLE ROLLER GUIDE 50MMMSP LOCKABLE CONDUIT ROLLER GUIDES

Unit: EA Qty: 1

Part No. MSS-FS-063 • To suit 63mm conduit• Min 48mm adjustable split lock OD• Full ball bearing roller guide• Chrome zinc plated finish

LOCKABLE ROLLER GUIDE 63MM Unit: EA Qty: 1






19





Part No. MSS-LN1478 • Water based cable blowing lubricant specifically designed for lubricating sub-duct prior to high speed fibre optic cable blowing• Compatible with all forms of cable jacket• Does not stress crack Polyethylene plastics• 20LTR Drum

DUCTGLIDE CABLE BLOWING LUBE 20LTR Unit: EA Qty: 1

• Water based cable hauling lubricant for excellent friction reduction - non-toxic and non-flammable• For hauling heavy power, telecommunication and fibre optic cable• Compatible with all forms of cable jacket• 20LTR Drum

MSP CABLE LUBRICANT


MSS-LN1477 POWERGEL CABLE HAULING LUBE 20LTR EA 1

MSS-LN1477-4 POWERGEL - 4LTR PALE EA 1

CABLE LUBRICANT


20

Part No. MSS-LPPHTA12 • Hauling rope with a break load of 2700kg• Material: Polypropylene• 250m coil

POLY PROP ROPE 12MM X 250MTRMSP HAULING ROPE

HAULING ROPE

Unit: EA Qty: 1

Part No. MSS-LPPHTG16 • Hauling rope with a break load of 4500kg• Material: Polypropylene• 250m coil

POLY PROP ROPE 16MM X 250MTR Unit: EA Qty: 1

Part No. MSS-LPPHTA20 • Hauling rope with a break load of 6900kg• Material: Polypropylene• 250m coil

POLY PROP ROPE 20MM X 250MTR Unit: EA Qty: 1

Part No. MSS-C-1250-0001-01 • Capable of installing fibre optic cable (6-32mm O.D. ) at speeds up to 90m per minute into pre installed sub-duct (25-63mm)• Electronic monitoring system provides read out of speed/distance• Electronic pressure sensor shuts off machine for obstructions• Collets and seals are required for cables and sub-duct• Includes portable petrol engine driven hydraulic pump and hoses

TORNADO CABLE BLOWING MACHINEMSP CABLE BLOWERS

CABLE BLOWERS

Unit: EA Qty: 1

Part No. MSS-C-1254-001-01 • Designed to install new a cable into an occupied sub-duct (subject to space)• Heavy-duty Aluminium base and lid• Collets and seals are required for cables and sub-duct

JUNCTION BOX FOR OVERBLOWING Unit: EA Qty: 1


21

Part No. MSS-EBK2-1300K • Effective in blowing a light-weight jet line up to 1000m of unoccupied conduit• Each motor (x 2 off) delivers approx. 3.5m3 of air per minute• Incl 3 x rope grommets for 3mm, 5mm and 5mm draw line• Incl 3x conduit sealoffs to suit 12mm up to 160mm conduit• Replacement blower ‘ONLY’ available p/n MSS-EBK2-1300

ELECTRIC JETLINE BLOWER KIT Unit: EA Qty: 1

Part No. MSS-DPL-500 • Used in conjunction with an air compressor• Suitable for conduits 50-150mm• Can accommodate rope 4-10mm• Complete kit supplied with carry case• 40mm conduit seal off available

CONDUIT ROPING KIT Unit: EA Qty: 1

• Shaped like a balloon with a rigid plastic mouth to ensure that the balloon stays inflated• Various sizes available

MSP LINE CARRIERS


MSS-DBL-035 BALLOON LINE CARRIER - 35MM EA 1









LINE CARRIERS


22

• Ideal for internal cleaning of ducts and conduits of debris• Galvanised finish• Made with 22g wire strand

MSP WIRE BRUSH CONDUIT CLEANERS


MSS-WBC-050 WIRE BRUSH MANDREL - 50MM EA 1

MSS-WBC-080 WIRE BRUSH MANDREL - 80MM EA 1

MSS-WBC-100 WIRE BRUSH MANDREL - PROVING / CLEANING EA 1

MSS-WBC-125 WIRE BRUSH MANDREL - PROVING / CLEANING EA 1

MSS-WBC-150 WIRE BRUSH CLEANER 22G WIRE FOR 150MM EA 1

MSS-WBC-200 WIRE BRUSH CLEANER 22G WIRE FOR 200MM EA 1

CLEANERS AND MANDRELS

• Suitable for clearing the conduit of sand, mud and other debris

MSSP CONDUIT CLEANERS


MSS-CRC-050 RUBBER CONDUIT CLEANER - 53MMOD CRC-050T EA 1

MSS-CRC-080 RUBBER CONDUIT CLEANER - 80MM EA 1




Used for testing conduit integrity before hauling cableTest electrical communications conduits

MSP DUCT PROVING MANDRELS


MSS-DPM-010 PROVING MANDREL 10MM O/D EA 1






MSS-DPM-030 DUCT PROVING MANDREL 28MM O/D EA 1

MSS-DPM-050 PROVING MANDREL 47MM OD EA 1




MSS-DPM-150 PROVING MANDREL 150MM -OD 130MM EA 1


23

• Used for spreading lubricant especially on tight radius corners• Suitable for clearing the conduit of sand, mud and other debris• Various sizes available

MSP LUBE SPREADERS


MSS-RS-050 LUBE SPREADER - 50MM EA 1





Part No. MSS-70188 • A breakaway swivel with standard fuse providing invaluable protection when pulling either fibre optic or coaxial cable• Made from high quality steel• Simple and inexpensive• Other sizes (kN) available• 16mm OD

FUSEABLE SWIVEL - 16MM OD - 2.2KNMSP STAINLESS STEEL HAULING SWIVELS

HAULING SWIVELS

Unit: EA Qty: 1

Part No. MSS-53706 • A breakaway swivel with standard fuse providing invaluable protection when pulling either fibre optic or coaxial cable• Made from high quality Aluminium• Simple and inexpensive• Other sizes (kN) available• 22mm OD

FUSEABLE SWIVEL - 22MM OD - 2.2KN Unit: EA Qty: 1

• Tough swivels designed to handle higher thrust loads for extra cable safety and faster straight pulls• Made from high quality stainless steel• Higher workload ratings than comparably sized swivels• Thrust bearing for tensile load - radial bearing for bending load


MSS-70137 STAINLESS HAULING 22.2 KN SWIVEL-31.8MM EA 1

MSS-70138 STAINLESS HAULING 31.1 KN SWIVEL-34MM EA 1

MSS-70139 STAINLESS HAULING 44.5 KN SWIVEL-41MM EA 1

MSS-70140 STAINLESS HAULING 111.2KN SWIVEL-64MM EA 1


24

Part No. MSS-26309 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 22mm Aluminium swivel and fuse bolts also available

FUSE FOR 16MM SWIVEL - 0.9KN - OR-WHMSP FUSE BOLTS

Unit: EA Qty: 1


FUSE FOR 16MM SWIVEL - 1.0KN - RD-WH Unit: EA Qty: 1

Part No. MSS-26305 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and Inexpensive• 22mm Aluminium swivel and fuse bolts also available

FUSE FOR 16MM SWIVEL - 1.3KN - GR-WH Unit: EA Qty: 1


FUSE FOR 16MM SWIVEL - 1.5KN - WH Unit: EA Qty: 1


FUSE FOR 16MM SWIVEL - 1.8KN - BL-WH Unit: EA Qty: 1


25


FUSE FOR 16MM SWIVEL - 1.9KN - YL-WH Unit: EA Qty: 1


FUSE FOR 16MM SWIVEL - 1.97KN - VI-WH Unit: EA Qty: 1


FUSE FOR 16MM SWIVEL - 2.0KN - OR Unit: EA Qty: 1


FUSE FOR 16MM SWIVEL - 2.2KN - VIOLET Unit: EA Qty: 1


FUSE FOR 16MM SWIVEL 2.7KN -YELLOW Unit: EA Qty: 1


26


FUSE FOR 16MM SWIVEL - 3.17KN - BROWN Unit: EA Qty: 1

Part No. MSS-30332 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 16mm steel swivel and fuse bolts also available

FUSE BOLT -1.5KN WHITE SUIT 22MM SWIVEL Unit: EA Qty: 1


FUSE BOLT -2.0KN ORANGE SUIT 22MM SWIVEL Unit: EA Qty: 1


FUSE BOLT -2.7KN YELLOW SUIT 22MM SWIVEL Unit: EA Qty: 1


FUSE BOLT -3.6KN BLUE-SUIT 22MM SWIVEL Unit: EA Qty: 1


27


FUSE BOLT -4.5KN GREEN-SUIT 22MM SWIVEL Unit: EA Qty: 1


FUSE BOLT -5.4KN RED- SUIT 22MM SWIVEL Unit: EA Qty: 1

Part No. MSS-NGKA-05 • Dillon AP mechanical dynamometer - uncomplicated operation includes tare function and maximum peak load indicator• Suitable for up to 500kg in 5kg increments• Includes rugged plastic storage case

DYNAMOMETER - 500KG X 5KG- DIALMSP LINE TENSIONERS

LINE TENSIONERS

Unit: EA Qty: 1

Part No. MSS-NGKA-50 • Dillon AP mechanical dynamometer - uncomplicated operation includes tare function and maximum peak load indicator• Suitable for up to 5000kg in 50kg increments• Includes rugged plastic storage case

DYNAMOMETER - 5000KG X 50KG- DIAL Unit: EA Qty: 1

Part No. MSS-HTNS-10KEP-D • Provides continuous pulling tension readout for safer and more efficient cable installation• Self-contained, weather tight case with instructions• Digital readout and preset alarm• Weight capacity 4500kg (10,000lb)

RUNNING LINE TENSIOMETER - 0-4500KG Unit: EA Qty: 1


28

• Designed for pulling bundles of Aerial Bundled Conductors (ABC Cables)• Non-conductive materials for safety• Standard is tubular, soft eye and alloy ferrule• Double and offset eye also available

CABAC ABC CABLE STOCKINGS


CGLV450 CABLE STOCKING 4X50MM2ABC EA 1

CGLV495 CABLE STOCKING 4X95MM2 ABC EA 1

CGLV4150 CABLE STOCKING 4X150MM2ABC EA 1

CABLE STOCKING

• High tension rope and conductor hauling to suit bare or insulated conductor• Copper shoulders provide protection from wear• Featuring an alloy ferrule and a soft eye• Variations e.g. galvanised thimbles available on request

CABAC HD CU SHOULDER CABLE STOCKINGS


CG10HD-CS CABLE STOCKING 10-15MM- HD / CU SHOULDER EA 1




• Lace up design allows the grip to be wrapped around the cable at any position secured by a lace• Can be used in central portion of a hauling job to share load• Ideal for retrofit in an industrial or mining application• Variations e.g. galvanised thimbles available on request

CABAC OFFSET EYE LACE UP CABLE STOCKINGS


CG14LU CABLE STOCKING 14-19MML/UP EA 1



CG45LU CABLE STOCK 40-55MM L/UP EA 1




CG165LU CABLE STOCKNG 150/190MML/UP EA 1


29

• Double eye design allows the cable to be lifted into position with one eye, while the other eye is used to anchor the cable to a fixture

• Featuring an alloy ferrule and a soft eye• Variations e.g. galvanised thimbles available on request

CABAC TUBULAR DOUBLE EYE CABLE STOCKINGS


CG10DE CABLE STOCKING 10-14MM GAL STRND AL FER EA 1

CG14DE CABLE STOCKING 14-19MM D/EYE EA 1






CG105DE CABLE STOCKING 95-120MMD/EYE EA 1



Part No. CG30DE-GT • Double eye design allows the cable to be lifted into position with one eye, while the other eye is used to anchor the cable to a fixture• Featuring an alloy ferrule and a Galvanised thimble• Variations available on request

CABLE STOCKING 28-40MM D/EYE GAL THIMLECABAC TUBULAR DOUBLE EYE GALVANISED CABLE STOCKING

Unit: EA Qty: 1

• Lace up design allows the grip to be wrapped around the cable at any position secured by a lace• Can be used in central portion of a hauling job to share load• Ideal for retrofit in an industrial or mining application• Variations available on request

CABAC TUBULAR DOUBLE EYE LACE UP SS CABLE STOCKING


CG45LU/DE-SS-SF-ST CABLE STOCKING 40-55MM L/UP D/EYE SS EA 1

CG60LU/DE-SS-SF-ST CABLE STOCKING 55-75MM L/UP D/EYE SS EA 1


30

• Double eye design allows the cable to be lifted into position with one eye, while the other eye is used to anchor the cable to a fixture

• Featuring Stainless Steel rope, ferrule and thimble• Variations available on request

CABAC TUBULAR DOUBLE EYE SS CABLE STOCKINGS


CG10DE-SS-SF-ST CABLE STOCKING 10-14MM D/E SS-SF-ST EA 1


CG20DE-SS-SF-ST CABLE STOCKING 19-28MM DOUBLE EYE EA 1

CG30DE-SS-SF-ST CABLE STOCKING 28-40MM D/EYE SS-SF-ST EA 1

CG45DE-SS-SF-ST CABLE STOCKING 40-55MM D/EYE SS-SF-ST EA 1



• Tubular offset eye allows the cable to be passed through the grip and secured at any point along the cable• Mainly used for strain relief• Featuring an alloy ferrule and a soft eye• Variations e.g. galvanised thimbles available on request

CABAC TUBULAR OFFSET EYE CABLE STOCKINGS


CG10OE CABLE STOCKING 10-14MM O/SET EA 1







CG105OE CABLE STOCKING 95-120MMO/SET EA 1

CG165OE CABLE STOCKING 150-190MM OFFSET EYE EA 1

Part No. CG20OE-GT • Tubular offset eye allows the cable to be passed through the grip and secured at any point along the cable• Mainly used for strain relief• Featuring an alloy ferrule and a Galvanised thimble• Variations available on request

CABLE STOCKING 19-28MM O/SETCABAC TUBULAR OFFSET EYE GALVINISED CABLE STOCKING

Unit: EA Qty: 1


31

• Tubular offset eye allows the cable to be passed through the grip and secured at any point along the cable• Mainly used for strain relief• Featuring Stainless Steel rope, ferrule and thimble• Variations available on request

CABAC TUBULAR OFFSET EYE SS CABLE STOCKINGS


CG14OE-SS-SF-ST CABLE STOCKING 14-19MM O/SET EA 1

CG20OE-SS-SF-ST CABLE STOCKING 19-28MM O/SET EA 1

CG30OE-SS-SF-ST CABLE STOCKING 28-40MM OFFSET EYE SF SS EA 1

• Tubular single eye used for general cable hauling• Slipped over the end of a cable and grip when pulled• Featuring an alloy ferrule and a soft eye• Variations e.g. galvanised thimbles available on request

CABAC TUBULAR SINGLE EYE CABLE STOCKINGS


CG10 CABLE STOCKING 10-14MM EA 1










• Lace up design allows the grip to be wrapped around the cable at any position secured by a lace• Can be used in central portion of a hauling job to share load• Ideal for retrofit in an industrial or mining application• Variations available on request

CABAC TUBULAR SINGLE EYE LACE UP SS CABLE STOCKING


CG20LU-SS-SF-ST CABLE STOCKING 19-28MML/UP S/S S/F S/T EA 1

CG30LU-SS-SF-ST CABLE STOCKING 28-40MML/UP SS-SF-ST EA 1

CG75LU-SS-SF-ST CABLE STOCK 75-95MM L/UP SS/SF/ST EA 1

CG105LU-SS-SF-ST CABLE STOCK 95-120MM L/UP SS/SF/ST EA 1


32

• Tubular single eye used for general cable hauling• Slipped over the end of a cable and grip when pulled• Featuring Stainless Steel rope, ferrule and thimble• Variations available on request

CABAC TUBULAR SINGLE EYE SS CABLE STOCKINGS


CG10-SS-SF-ST CABLE STOCKING 10-14MM SS/SF/ST EA 1







• Used when there is a possibility of rotation or spinning, passing from the pilot rope to the cable, or vice-versa

• Low friction ball bearing swivel made from stainless steel• Screwdriver slots in pins for easy removal• Clevis/Eye type is also available

CABAC SWIVELS


CGSSSW19CC BEARING SWIVEL 19MM DIAMETER 1.5T U.T.S EA 1

CGSSSW25CC BEARING SWIVEL 25MM DIAMETER 2.5T U.T.S EA 1

Part No. MSS-C1405-AU • Skid mounted hydraulic pull and assist double capstan winch with capstan tilt function and rope take-up drum• User friendly power mounted controls• Winch stops pulling at selected tension without engine shut down• Removable take-up drum for easy rope removal• Pulling capacity- 500kg large capstan, 1000kg small capstan

TILTING CAPSTAN F OP WINCH - SKIDMSP CABLE PULLERS

CABLE PULLERS

Unit: EA Qty: 1

Part No. MSS-H2500 • 240 Volt single phase cable puller with a dual pulling capacity of 2500kg and 1500kg• Overload protection switch - ensures automatic shut-off• Electromagnetic spring-applied fail safe brake• Rugged high power induction motor for proven reliability

240V CAPSTAN WINCH - 2.5TON Unit: EA Qty: 1


33

Part No. MSS-MGA-070 • Suitable for storage in a station wagon or sedan• For providing a safe and sheltered working environment• Colour: Yellow

FOLDAWAY BARRIER FRAME SET- NO ROOFMSSP GUARDS

MANHOLE EQUIPMENT

Unit: EA Qty: 1

Part No. MSS-SMTF38 • NOT approved for Telstra use• For providing a safe and sheltered working environment• Colour: Yellow

MANHOLE BARRIER GUARD - YELLOW - NO ROOF Unit: EA Qty: 1

Part No. MSS-MGA-140Y • For providing a safe and sheltered working environment• Approved for Telstra use• Rugged and reliable• Colour: Yellow

MANHOLE BARRIER SET - NO ROOF Unit: EA Qty: 1

Part No. MSS-MGA-140RY • Manhole barrier set to suit a tent frame• Manhole guard tent sold separately - Part No. MSS-TENT-01• For providing a safe and sheltered working environment• approved for Telstra use

MANHOLE BARRIER SET WITH ROOF FRAME Unit: EA Qty: 1

Part No. MSS-TENT-01 • Waterproof canvas• Window and door flap design• Frame sold separately - Part No. MSS-MGA-140RY• For providing a safe and sheltered working environment

MANHOLE GUARD TENT WITH ROOF WINDOW Unit: EA Qty: 1


34

Part No. MSS-TEL83-41 • Designed to protect workers from the elements - bright in colour, the tent is easily seen by oncoming traffic• Unique hub design - tent pops up or down in seconds• Durable water repellent fabric• Features adjustable rod ends for side wall tension• Fire resistant

FIBRE SPLICING TENT - 1.8X1.8X1.8MTR Unit: EA Qty: 1

Part No. MSS-GAT-LONG • Long handle lid lifter is used in pairs to break stubborn, dirt ingress seals and to lift medium-duty pit lids and grates• Use with the short handle key (Part No. MSS-GAT-SHORT)• Weight: 1.8kg• Handle length: 740mm

GATTIC - LID LIFTER - LONG HANDLEMSP PIT KEYS AND BREAKERS

PIT KEYS AND BREAKER

Unit: EA Qty: 1

Part No. MSS-GAT-SMALL • Short handle lid lifter is used in pairs to break stubborn, dirt ingress seals and to lift smaller pit lids and grates• Small ‘D’ handle assists in breaking the dirt locked seal• Use with the long handle key (Part No. MSS-GAT-LONG)• Weight: 1.8kg

GATTIC - LID LIFTER - SHORT HANDLE Unit: EA Qty: 1

Part No. MSS-PB-100 • For use with Telstra pit keys• Lift stubborn lids with ease• Open manhole lids that may be stuck or jammed• Cover seal breaker also available (Part No. MSS-TEL116-00151A)

MANHOLE LID BREAKER Unit: EA Qty: 1

Part No. MSS-TEL116-00151A • Helps to ease man hole covers that have not been lifted for a long time• Manhole lid breaker also available Part No. MSS-PB-100

COVER SEAL BREAKER Unit: EA Qty: 1


35

Part No. MSS-TEL116-00152 • Standard pit key

M KEY - PIT KEY - 600MM Unit: EA Qty: 1

Part No. MSS-TEL116-00153 • Standard pit key

PIT L KEY - 670MM Unit: EA Qty: 1

Part No. MSS-TEL075-00122 • Quality extractor tool• Remove manhole keyhole plugs with ease

KEYHOLE PLUG EXTRACTOR TOOL Unit: EA Qty: 1

CABLE LAYING & EQUIPMENT

36

CG30OE-SS-SF-ST 31

CG30OE 30

CG45-SS-SF-ST 32

CG45 31

CG45DE-SS-SF-ST 30

CG45DE 29

CG45LU/DE-SS-SF-ST 29

CG45LU 28

CG45OE 30

CG60-SS-SF-ST 32

CG60 31

CG60DE-SS-SF-ST 30

CG60DE 29

CG60LU/DE-SS-SF-ST 29

CG60LU 28

CG60OE 30

CG75-SS-SF-ST 32

CG75 31

CG75DE-SS-SF-ST 30

CG75DE 29

CG75LU-SS-SF-ST 31

CG75LU 28

CG75OE 30

CGLV4150 28

CGLV450 28

CGLV495 28

CGSSSW19CC 32

CGSSSW25CC 32

FTCM30 4

FTGJ20 4

FTR6 4

FTRC 4

MSS-100505001 10

MSS-11FLEX 7

MSS-11TR-125 7

MSS-11TR-150 7

MSS-11TR-200 7

MSS-11TR-250 7

MSS-11TR-300 7

MSS-11TR-350 7

MSS-11TR-400 7

MSS-25493 25

MSS-25494 25

MSS-26305 24

45-235 11

CG10-SS-SF-ST 32

CG10 31

CG105 31

CG105DE 29

CG105LU-SS-SF-ST 31

CG105LU 28

CG105OE 30

CG10DE-SS-SF-ST 30

CG10DE 29

CG10HD-CS 28

CG10OE 30

CG135 31

CG135DE 29

CG14-SS-SF-ST 32

CG14 31

CG14DE-SS-SF-ST 30

CG14DE 29

CG14LU 28

CG14OE-SS-SF-ST 31

CG14OE 30

CG15HD-CS 28

CG165 31

CG165DE 29

CG165LU 28

CG165OE 30

CG20-SS-SF-ST 32

CG20 31

CG20DE-SS-SF-ST 30

CG20DE 29

CG20HD-CS 28

CG20LU-SS-SF-ST 31

CG20LU 28

CG20OE-GT 30

CG20OE-SS-SF-ST 31

CG20OE 30

CG30-SS-SF-ST 32

CG30 31

CG30DE-GT 29

CG30DE-SS-SF-ST 30

CG30DE 29

CG30HD-CS 28

CG30LU-SS-SF-ST 31

CG30LU 28

INDEX

MSS-26306 24

MSS-26307 25

MSS-26308 25

MSS-26309 24

MSS-26310 24

MSS-26325 25

MSS-26326 26

MSS-30332 26

MSS-30333 24

MSS-306311 10

MSS-34341 26

MSS-34342 26

MSS-34343 27

MSS-34344 27

MSS-34786 26

MSS-4.5-100 7

MSS-4.5-30 7

MSS-4.5-60 7

MSS-4.5-80 7

MSS-4.5FLEX 7

MSS-4JZ-DZ255S 14

MSS-53706 23

MSS-6FLEX 7

MSS-6TR-100 7

MSS-6TR-120 7

MSS-6TR-150 7

MSS-6TR-200 7

MSS-6TR-60 7

MSS-6TR-80 7

MSS-70137 23

MSS-70138 23

MSS-70139 23

MSS-70140 23

MSS-70188 23

MSS-9FLEX 7

MSS-9TR-100 7

MSS-9TR-125 7

MSS-9TR-150 7

MSS-9TR-200 7

MSS-9TR-250 7

MSS-BM100 17

MSS-BM125 17

MSS-BM150 17

MSS-C-1250-0001-01 20


37

MSS-C-1254-001-01 20

MSS-C1405-AU 32

MSS-CCG-028 17

MSS-CCG-035 17

MSS-CCG-050 17

MSS-CCG-080 17

MSS-CCG-100 17

MSS-CCG-125 17

MSS-CCG-150 17

MSS-CDT-500 13

MSS-CLS-050 17

MSS-CLS-080 17

MSS-CLS-100 17

MSS-CLS-125 17

MSS-CLS-150 17

MSS-CRC-050 22

MSS-CRC-080 22

MSS-CRC-100 22

MSS-CRC-125 22

MSS-CRC-150 22

MSS-CRS350 13

MSS-DB-400 14

MSS-DB-630 14

MSS-DB-660 14

MSS-DB-900 14

MSS-DBL-035 21

MSS-DBL-050 21

MSS-DBL-063 21

MSS-DBL-080 21

MSS-DBL-100 21

MSS-DBL-125 21

MSS-DBL-150 21

MSS-DBL-190 21

MSS-DBL-225 21

MSS-DJS-58T 14

MSS-DPL-500 21

MSS-DPM-010 22

MSS-DPM-014 22

MSS-DPM-015 22

MSS-DPM-018 22

MSS-DPM-020 22

MSS-DPM-022 22

MSS-DPM-030 22

MSS-DPM-050 22

MSS-DPM-080 22

MSS-DPM-100 22

MSS-DPM-125 22

MSS-DPM-150 22

MSS-DRR-1000 14

MSS-EBK2-1300K 21

MSS-FS-050 18

MSS-FS-063 18

MSS-FS-080 18

MSS-FS-100 18

MSS-FS-125 19

MSS-FS-150 19

MSS-GAT-LONG 34

MSS-GAT-SMALL 34

MSS-GCG30V 5

MSS-H2500 32

MSS-HTNS-10KEP-D 27

MSS-IFS-080 16

MSS-IFS-100 16

MSS-IFS-125 16

MSS-IFS-150 16

MSS-JK10.0-8.0 8

MSS-JK4.5-3.0 8

MSS-JK6.0-8.0 8

MSS-JK6.5-4.5 8

MSS-LN1477-4 19

MSS-LN1477 19

MSS-LN1478 19

MSS-LPPHTA12 20

MSS-LPPHTA20 20

MSS-LPPHTG16 20

MSS-MGA-070 33

MSS-MGA-140RY 33

MSS-MGA-140Y 33

MSS-NGKA-05 27

MSS-NGKA-50 27

MSS-NTR-120 15

MSS-NTRA-120 15

MSS-PB-100 34

MSS-PMCG-100 17

MSS-PMRG-140 18

MSS-RFL-11-125TR 8

MSS-RFL-11-150TR 8

MSS-RFL-11-200TR 8

MSS-RFL-11-250TR 8

MSS-RFL-11-300TR 8

MSS-RFL-11-350TR 8

MSS-RFL-11-400TR 8

MSS-RFL-4.5-30 8

MSS-RFL-4.5-60 8

MSS-RFL-4.5-80 8

MSS-RFL-6-100TR 8

MSS-RFL-6-120TR 8

MSS-RFL-6-150TR 8

MSS-RFL-6-60TR 8

MSS-RFL-6-80TR 8

MSS-RFL-9-100TR 8

MSS-RFL-9-125TR 8

MSS-RFL-9-150TR 8

MSS-RFL-9-200TR 8

MSS-RFL-9-250TR 8

MSS-RS-050 23

MSS-RS-080 23

MSS-RS-100 23

MSS-RS-125 23

MSS-RS-150 23

MSS-RTR-140 15

MSS-RTRA-140 15

MSS-SLS-05T 13

MSS-SLS1-2T 13

MSS-SLS3-4T 13

MSS-SMTF38 33

MSS-SV3366 10

MSS-TCH-22MF 5

MSS-TCR-200 15

MSS-TEL075-00122 35

MSS-TEL116-00151A 34

MSS-TEL116-00152 35

MSS-TEL116-00153 35

MSS-TEL414-105 9

MSS-TEL414-130 9

MSS-TEL414-50 9

MSS-TEL414-77 9

MSS-TEL414-82 8

MSS-TEL414-84 9


38

MSS-TEL83-41 34

MSS-TENT-01 33

MSS-TFL-22 5

MSS-THL-2290 6

MSS-THR-223M 5

MSS-TRE-22 6

MSS-TRGM-100-2 16

MSS-TRGM-100-3 16

MSS-TRGM-100 16

MSS-TX405C 10

MSS-WBC-050 22

MSS-WBC-080 22

MSS-WBC-100 22

MSS-WBC-125 22

MSS-WBC-150 22

MSS-WBC-200 22

P611001 11

P611002 11

P611003 11

P611004 11

P611005 11

P611007 11

P611009 11

P802163 3

P802164 3

PTS20M 3

PTS30M 3

In support of our policy of continuous product improvement we reserve the right to change materials and specifications without notice. Drawings, where used, are not to scale. All dimensions are in millimetres and sizes given are approximate. Where possible, technical MSDS data sheets are made available on the website. All products should be installed and used in accordance

with manufacturer’s instructions provided. Warning: products may be the subject of registered designs and patents. Refer to website for terms and conditions on warranty.

Every effort has been made to ensure accuracy of content. However no liability will be met by Legend Performance Technology or its suppliers for any errors or ommisions. Product data and information is not binding.

All brands and logos are registered trademarks and are subject to copyright laws.

No part of this catalogue can be reproduced without consent of Legend Performance Technology.

OVERHEADLPTV0117

cable laying & equipment...cable rollers 15 conduit cable guides 16 cable lubricant 19 hauling...

Documents