building envelope technologies ltd - inab · building envelope technologies ltd ballylacey...
TRANSCRIPT
Edition 12, 25/04/2018 193T Page 1 of 23
Building Envelope Technologies Ltd Ballylacey Crossroads, Inch, Gorey, Co Wexford. Y25 XW93.
Testing Laboratory
Registration number: 193T
is accredited by the Irish National Accreditation Board (INAB) to undertake testing as detailed in
the Schedule bearing the Registration Number detailed above, in compliance with the
International Standard ISO/IEC 17025:2005 2nd Edition
“General Requirements for the Competence of Testing and Calibration Laboratories”
(This Certificate must be read in conjunction with the Annexed Schedule of Accreditation)
Date of award of accreditation: 22:04:2008
Date of last renewal of accreditation: 25:04:2018
Expiry date of this certificate of accreditation: 25:04:2023
This Accreditation shall remain in force until further notice subject to continuing compliance
with INAB accreditation criteria, ISO/IEC 17025 and any further requirements specified by the
Irish National Accreditation Board.
Manager: ____________________ Chairperson: ____________________
Dr Adrienne Duff Ms Ita Kinahan
Issued on 25th April 2018
Organisations are subject to annual surveillance and are re-assessed every five years. The renewal date on this
Certificate confirms the latest date of renewal of accreditation. To confirm the validity of this Certificate, please
contact the Irish National Accreditation Board.
The INAB is a signatory of the European co-operation for Accreditation (EA) Testing Multilateral Agreement (MLA) and the
International Laboratory Accreditation Cooperation (ILAC) Mutual Recognition Arrangement.
Edition 12, 25/04/2018 193T Page 2 of 23
Schedule of Accreditation
(Annex to Accreditation Certificate) Permanent Laboratory:
Category A & D
BUILDING ENVELOPE TECHNOLOGIES LTD
Mechanical Testing Laboratory
Initial Registration Date : 22-April-2008
Postal Address:
(Address of other locations
as they apply)
Ballylacey Crossroads,
Inch,
Gorey,
Co Wexford.
Y25 XW93.
Telephone: 0402 21873
0402 21965
Fax:
E-mail: [email protected]
Contact Name: Brian Shannon
Facilities: Public testing service
Edition 12, 25/04/2018 193T Page 3 of 23
Schedule of Accreditation
Permanent Laboratory: Category A & D
THE IRISH NATIONAL ACCREDITATION BOARD (INAB) is the Irish body for the accreditation of
organisations including laboratories.
Laboratory accreditation is available to testing and calibration facilities operated by manufacturing
organisations, government departments, educational institutions and commercial testing/calibration
services. Indeed, any organisation involved in testing, measurement or calibration in any area of
technology can seek accreditation for the work it is undertaking.
Each accredited laboratory has been assessed by skilled specialist assessors and found to meet criteria
which are in compliance with ISO/IEC 17025 or ISO 15189 (medical laboratories). Frequent audits,
together with periodic inter-laboratory test programmes, ensure that these standards of operation are
maintained.
Testing and Calibration Categories:
Category A: Permanent laboratory calibration and testing where the laboratory is erected on a fixed
location for a period expected to be greater than three years.
Category B: Site calibration and testing that is performed by staff sent out on site by a permanent
laboratory that is accredited by the Irish National Accreditation Board.
Category C: Site calibration and testing that is performed in a site/mobile laboratory or by staff sent
out by such a laboratory, the operation of which is the responsibility of a permanent
laboratory accredited by the Irish National Accreditation Board.
Category D: Site calibration and testing that is performed on site by individuals and organisations that
do not have a permanent calibration/testing laboratory. Testing may be performed using
(a) portable test equipment
(b) a site laboratory
(c) a mobile laboratory or
(d) equipment from a mobile or site laboratory
Standard Specification or Test Procedure Used:
The standard specification or test procedure that is accredited is the issue that is current on the date of the most
recent visit, unless otherwise stated.
Glossary of Terms
Facilities:
Public calibration/testing service: Commercial operations which actively seek work from others.
Conditionally available for public
calibration/testing:
Established for another primary purpose but, more commonly than not,
is available for outside work.
Normally not available for public
calibration/testing:
Unavailable for public calibration/testing more often than not.
Laboratory users wishing to obtain assurance that calibration or test results are reliable and carried out to the Irish
National Accreditation Board criteria should insist on receiving an accredited calibration certificate or test report.
Users should contact the laboratory directly to ensure that this scope of accreditation is current. INAB will, on
request, verify the status and scope.
Edition 12, 25/04/2018 193T Page 4 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category A
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing of
Buildings
Water Penetration – Hose Test
Water Penetration – Spray Bar
Test
Documented in house Test
Method CWCT_TM-01 and
CWCT_TM-02
based on:
-CWCT Standard Test
Method For Water
Penetration - HOSE TEST
Section 9.0
-CWCT Standard SITE Test
For Water Penetration -
SPRAY BAR TEST Section
10.0
- CWCT TN:41 Technical
Note No 41 "Site testing for
water tightness"
- BS EN 13051:2001 Curtain
walling - Water tightness -
Site test
Edition 12, 25/04/2018 193T Page 5 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category A
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing of
Buildings
Slip Resistance Testing
Documented in house Test Method LAB_TM-07 based on: BS EN 7976-2-2002+A1:2013
Pendulum testers Part 2:
Method of operation.
BS EN 13036-4:2011 Road
and airfield surface
characteristics – Test
Methods Part 4: Method for
Measurement of slip/skid
resistance of a surface: The
Pendulum Test.
UK Slip Resistance
Guidelines
Edition 12, 25/04/2018 193T Page 6 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category A
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing of
Buildings
Impact Testing
Documented in house Test Method LAB_TM-05 based on:
CWCT Part 8: Section 8.10 Page 15 CWCT Section 15.0 (Method of Test for Impact Test) CWCT Section 16.0 (Method of Test for Fragility) Section 16.0 Fragility ACR[M]001:2014 Test For Non-Fragility of Large Element Roofing Assemblies [Fifth Edition] Technical Note No 67 Supersedes TN 42 Safety and Fragility of Glazed Roofing: Testing and Assessment Technical Note No 66 Safety and Fragility of Glazed Roofing: Guidance on Specification BS EN 356:1999 Glass in Building-Security Glazing-Testing and Classification of resistance against manual attack Technical Note No 92 Simplified Method for Assessing Glazing in Class 2 Roofs
Section 15.0 Impact
Edition 12, 25/04/2018 193T Page 7 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category A
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing of
Buildings
Impact Testing
Documented in house Test Method LAB_TM-05 based on:
BS EN 12600:2002 Glass in building-Pendulum test-Impact Test method and classification for flat glass BS EN 8200:1985 Code of practice for-Design of non-loading external vertical enclosures of buildings Technical Note No 65 Thermal Fracture of Glass Technical Note No 75 Supersedes TN52 Impact Performance of Building Envelopes: Guidance on Specification Technical Note No 76 Supersedes TN52 Impact Performance of Building Envelopes: Method for Impact Testing of Cladding Panels
Edition 12, 25/04/2018 193T Page 8 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category A
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing of
Buildings
AIR PERMEABILITY LABORTORY TESTING Air Permeability: Windows & Doors Air Permeability: Curtain Walling & Cladding Components
Documented in house Test Method LAB_TM-01 based on: EN 1026:1999 Windows and Doors – Air Permeability– Test Method. EN 12207:1999 Windows and Doors – Air Permeability – Classification CWCT Section 5.0 & CWCT Part 3 section 3.3 EN 12153-2000 Curtain Walling – Air Permeability– Test Method. EN 12152-1999 Curtain Walling – Air Permeability– Perfromance Requirements and Classification.
Edition 12, 25/04/2018 193T Page 9 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category A
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing of
Buildings
WATERTIGHTNESS LABORATORY
TESTING
Watertightness:
Windows & Doors
Watertightness:
Curtain Walling & Cladding
Components
Documented in house Test
Method LAB_TM-03 based
on:
EN 1027:2000 Windows and
Doors – Water Tightness -
Test Method.
EN 12208:2000 Windows and
Doors – Water Tightness -
Classification
CWCT Section 6.0 & CWCT
Part 3 section 3.4
EN 12155:2000 Curtain
Walling – Water Tightness -
Test Method.
EN 12154- 1999 Curtain
Walling – Watertightness–
Perfromance Requirements
and Classification.
Edition 12, 25/04/2018 193T Page 10 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category A
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing
of Buildings
- Products
RESISTANCE TO WIND LOAD
LABORATORY TESTING
Resistance Due to Wind
Loading:
WINDOWS & DOORS
Resistance Due to Wind
Loading:
CURTAIN WALLING & CLADDING
SYSTEMS
Documented in house Test
Method LAB_TM-02 based
on:
EN 12211:2000 Windows and
Doors - Resistance to Wind
Load Test- Test Method.
EN 12210:2000 Windows and
Doors - Resistance to Wind
Load Test- Classification.
CWCT Section 11.0 & CWCT
Section 12
EN 12179:2000 Curtain
Walling - Resistance to Wind
Load Test -Test Method.
EN 13116- 2001 Curtain
Walling - Resistance to Wind
Load -Performance
Requirements.
Edition 12, 25/04/2018 193T Page 11 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category A
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing
of Buildings
- Products
SEISMIC/DIFFERENTIAL
MOVEMENT TESTING
Vertical & Lateral
Seismic/Differential Movement:
VERTICAL & LATERAL
Documented in house Test Method LAB_TM-04 based on: AAMA 501.4-09 Seismic – LATERAL WIND SWAY- Test Method AAMA 501.7-11 Seismic – VERTICAL WIND SWAY- Test Method CWCT Section 17 Structural Movement Regime.
.99 Environmental Testing
of Buildings
- Products
DYNAMIC - Aero Engine Test
Façade Elements including
Curtain Walling
Windows & Doors
Roof lights
Auto & Manual Opening Vents
External Wall Systems
Cladding Systems
Rainscreen Systems
Roof Cladding Systems
Documented in house Test Method LAB_TM-06 based on: AAMA 501.1-83 Dynamic Aero Engine - TEST METHOD. CWCT Section 7 Standard Test Method for Water Penetration- Dynamic AERO ENGINE TEST
Edition 12, 25/04/2018 193T Page 12 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category D
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing of
Buildings
Building Air leakage
permeability test
Airtightness Testing of:-
- Commercial Buildings
(TestM-02)
Range of Pressurised Air Flow
0.05m3/S to 63.3m3/S
T.G.D Part L (Buildings other
than Dwellings)
- Residential Buildings
(TestM-03)
Range of Pressurised Air Flow
0.05m3/S to 33.3m3/S
T.G.D Part L (Dwellings)
Documented in house Test
Method 02 and 03 based on
- BS EN 13829:2000, Part 1,
"Determination of air
permeability of buildings,
fan pressurised methods"
- ATTMA (Air-tightness
Testing and measurement
association) Technical
Standard TS -1: July 2007.
- ATTMA Technical Standard
L2 (Non-Dwellings) October
2011
- TM 23 of 2002 Testing
Buildings for Air Leakage
CIBSE (Chartered
Institution of Building
Services Engineers).
- ATTMA Technical Standard
L1 (Dwellings) October 2010
-H.B.N Supplement 1:
Hospital Isolation Facilities
in Acute Settings
Appendix II Acceptance
testing of Isolation Suite
Edition 12, 25/04/2018 193T Page 13 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category D
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing of
Buildings
Building Air leakage
permeability test
Airtightness Testing of:-
- Commercial Buildings
(TestM-02)
Range of Pressurised Air Flow
0.05m3/S to 63.3m3/S
T.G.D Part L (Buildings other
than Dwellings) fully
Compliant.
- Residential Buildings
(TestM-03)
Range of Pressurised Air Flow
0.05m3/S to 33.3m3/S
T.G.D Part L (Dwellings) fully
Compliant.
Documented in house Test
Method 02 and 03 and 16
based on
- BS EN ISO:9972 2015,
"Thermal performance of
buildings - Determination of
air permeability of
buildings-Fan pressurization
method"
(Residential & Commercial
Buildings)
- ATTMA Technical Standard
L1 (Dwellings) September
2016
Edition 12, 25/04/2018 193T Page 14 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category D
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing
of Buildings
Water Penetration – Hose Test
Water Penetration – Spray Bar
Test
Documented in house Test
Method CWCT_TM-01 and
CWCT_TM-02
based on:
-CWCT Standard Test
Method For Water
Penetration - HOSE TEST
Section 9.0
-AAMA Test Method for Field
Hose Test
AAMA 501.2-03
-CWCT Standard SITE Test
For Water Penetration -
SPRAY BAR TEST Section
10.0
- CWCT TN:41 Technical
Note No 41 "Site testing for
water tightness"
- BS EN 13051:2001 Curtain
walling - Water tightness -
Site test
Edition 12, 25/04/2018 193T Page 15 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category D
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing of
Buildings
Sound Insulation Testing (Acoustic Testing)
Technical Guidance Document
Part E
2014 Appendix A Test
Procedure fully Compliant.
Building Regulations (Northern
Ireland) 2012. Technical
Booklet G
Technical Guidance Document TGD-021-5 Acoustic Performance in New Primary & Post Primary School Buildings (1St Edition, February 2013)
Revision 1, November 2015
Documented in house Test Method LAB_TM-08 based on: EN 16283-1:2014 Acoustics – Field measurement of sound insulation in buildings and of building elements -
Airborne.
EN 16283-2:2015 Acoustics - Field measurement of sound insulation in buildings and of
building elements - Impact
EN 16283-2:2014 Acoustics – Field measurement of sound insulation in buildings and of
building elements - Impact
EN 140-7:1998 Acoustics – Measurement of sound insulation in buildings and of building elements – Impact
EN 140-4:1998 Acoustics – Field measurement of sound insulation in buildings and of building elements -
Airborne.
EN 717-1:2013 Acoustics Rating of sound insulation in buildings and of building
elements - Airborne
EN ISO 354:2003 Acoustics - Measurement of sound absorption in a reverberation room
Edition 12, 25/04/2018 193T Page 16 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category D
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing of
Buildings
Sound Insulation Testing (Acoustic Testing)
Technical Guidance Document
Part E
2014 Appendix A Test
Procedure fully Compliant.
Documented in house Test Method LAB_TM-08 based on: EN 717-2:2013 Acoustics Rating of sound insulation in buildings and of building elements - Impact
EN 3382-2-2008 Acoustics – Measurement of room acoustic parameters – Reverberation in ordinary
rooms.
1145
.99
Environmental Tests
Other Tests
Environmental Testing of
Buildings
- Products
Slip Resistance Testing
Documented in house Test Method LAB_TM-07 based on: BS EN 7976-2-2002+A1:2013
Pendulum testers Part 2:
Method of operation.
BS EN 13036-4:2011 Road
and airfield surface
characteristics – Test
Methods Part 4: Method for
Measurement of slip/skid
resistance of a surface: The
Pendulum Test.
UK Slip Resistance
Guidelines
Edition 12, 25/04/2018 193T Page 17 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category D
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing
of Buildings
- Products
Impact Testing Documented in house Test Method LAB_TM-05 based on:
CWCT Part 8: Section 8.10 Page 15 CWCT Section 15.0 (Method of Test for Impact Test) CWCT Section 16.0 (Method of Test for Fragility) Section 16.0 Fragility ACR[M]001:2014 Test For Non-Fragility of Large Element Roofing Assemblies [Fifth Edition] Technical Note No 67 Supersedes TN 42 Safety and Fragility of Glazed Roofing: Testing and Assessment Technical Note No 66 Safety and Fragility of Glazed Roofing: Guidance on Specification BS EN 356:1999 Glass in Building-Security Glazing-Testing and Classification of resistance against manual attack Technical Note No 92 Simplified Method for Assessing Glazing in Class 2 Roofs
Section 15.0 Impact
Edition 12, 25/04/2018 193T Page 18 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category D
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing
of Buildings
- Products
Impact Testing Documented in house Test Method LAB_TM-05 based on:
BS EN 12600:2002 Glass in building-Pendulum test-Impact Test method and classification for flat glass BS EN 8200:1985 Code of practice for-Design of non-loading external vertical enclosures of buildings Technical Note No 65 Thermal Fracture of Glass Technical Note No 75 Supersedes TN52 Impact Performance of Building Envelopes: Guidance on Specification Technical Note No 76 Supersedes TN52 Impact Performance of Building Envelopes: Method for Impact Testing of Cladding Panels
Edition 12, 25/04/2018 193T Page 19 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category D
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing
of Buildings
- Products
AIR PERMEABILITY LABORTORY TESTING Air Permeability: Windows & Doors Air Permeability: Curtain Walling & Cladding Components
Documented in house Test Method LAB_TM-01 based on: EN 1026:1999 Windows and Doors – Air Permeability– Test Method. EN 12207:1999 Windows and Doors – Air Permeability – Classification CWCT Section 5.0 & CWCT Part 3 section 3.3 EN 12153-2000 Curtain Walling – Air Permeability– Test Method. EN 12152-1999 Curtain Walling – Air Permeability– Perfromance Requirements and Classification.
Edition 12, 25/04/2018 193T Page 20 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category D
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing
of Buildings
- Products
WATERTIGHTNESS LABORATORY
TESTING
Watertightness:
Windows & Doors
Watertightness:
Curtain Walling & Cladding
Components
Documented in house Test
Method LAB_TM-03 based
on:
EN 1027:2000 Windows and
Doors – Water Tightness -
Test Method.
EN 12208:2000 Windows and
Doors – Water Tightness -
Classification
CWCT Section 6.0 & CWCT
Part 3 section 3.4
EN 12155:2000 Curtain
Walling – Water Tightness -
Test Method.
EN 12154- 1999 Curtain
Walling – Watertightness–
Perfromance Requirements
and Classification.
Edition 12, 25/04/2018 193T Page 21 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category D
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing
of Buildings
- Products
RESISTANCE TO WIND LOAD
LABORATORY TESTING
Resistance Due to Wind
Loading:
WINDOWS & DOORS
Resistance Due to Wind
Loading:
CURTAIN WALLING & CLADDING
SYSTEMS
Documented in house Test
Method LAB_TM-02 based
on:
EN 12211:2000 Windows and
Doors - Resistance to Wind
Load Test- Test Method.
EN 12210:2000 Windows and
Doors - Resistance to Wind
Load Test- Classification.
CWCT Section 11.0 & CWCT
Section 12
EN 12179:2000 Curtain
Walling - Resistance to Wind
Load Test -Test Method.
EN 13116- 2001 Curtain
Walling - Resistance to Wind
Load -Performance
Requirements.
Edition 12, 25/04/2018 193T Page 22 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category D
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing
of Buildings
- Products
SEISMIC/DIFFERENTIAL
MOVEMENT TESTING
Vertical & Lateral
Seismic/Differential Movement:
VERTICAL & LATERAL
Documented in house Test Method LAB_TM-04 based on: AAMA 501.4-09 Seismic – LATERAL WIND SWAY- Test Method AAMA 501.7-11 Seismic – VERTICAL WIND SWAY- Test Method CWCT Section 17 Structural Movement Regime.
.99 Environmental Testing
of Buildings
- Products
DYNAMIC - Aero Engine Test
Façade Elements including
Curtain Walling
Windows & Doors
Roof lights
Auto & Manual Opening Vents
External Wall Systems
Cladding Systems
Rainscreen Systems
Roof Cladding Systems
Documented in house Test Method LAB_TM-06 based on: AAMA 501.1-83 Dynamic Aero Engine - TEST METHOD. CWCT Section 7 Standard Test Method for Water Penetration- Dynamic AERO ENGINE TEST
Edition 12, 25/04/2018 193T Page 23 of 23
Scope of Accreditation
Building Envelope Technologies Ltd Permanent Laboratory:
Category D
Mechanical Testing Laboratory
INAB Classification number (P9)
Materials/products tested
Type of test/properties
measured
Range of measurement
Standard specifications
Equipment/techniques used
1145
.99
Environmental Tests
Other Tests
Environmental Testing
of Buildings
Performance testing and
installation checks of
residential ventilation systems
Air flow range (supply and
exhaust)
10-550m3/h with zero pressure
compensation
551-850 m3/h with calculated
compensation
Documented in house method SUS_TM-01 based on: EN14134:2004 (Stage F) Building Regulations 2209 Technical Guidance document F
1145
.99
Environmental Tests
Other Tests
Environmental Testing
of Buildings
Performance of windows and
doors for weathertightness
AIRTIGHTNESS
Class 0 to Class 4
WATERTIGHTNESS
Class 0 to Class 9a
RESISTANCE TO WIND LOAD
Class A2 to Class A5
Documented in-house test method LAB-TM-09 based on: BS6375-1:2015 Part 1