bmw e46 tool

Engine (M52TU)

Explanation:

P Belongs to measuring and test equipment (minimum requirement)

M Belongs to tools (minimum requirement)

* Part of a tool kit

11 0 000 M Engine hoist for removing and installing enginesEngine: M10, M60, M62, M70, M73, S14

11 0 001 * Lifting bar

11 0 002 * Chain, long

11 0 003 * Chain, short

11 0 009 * Shackle (2)

11 0 010 Spacer for supporting engine while removing and installing transmissionEngine: M70

11 0 020 M Engine hoist for removing and installing enginesEngine: M20, M20B25, M20B27, M21, M30, M30B34, M30Tur, M50, M51,M52, S38, S50B30, S50B32, S50US


11 0 022 * Chain, centre

11 0 023 * Chain, long

11 0 024 * Chain, short

11 0 029 * Shackle (2)

11 0 030 M Engine mounting fixture for removing and installing engineUsed together with: 11 0 020Engine: M50, M52

11 0 060 Pressing fixture for crankcaseUsed together with: 11 1 031, 11 1 032Engine: M21

11 0 061 * Water pump cover plate incl. valve

11 0 062 * Stud bolt (14)

SWK Numbers catalogue main group 11 BMW AG - TIS 02.07.1998 15:50Valid only until next CD is issued Copyright Page - 1 -

11 0 070 Engine hoistFor removing and installing enginesEngine: M40, M41, M42, M43, M44, M47


11 0 072 * Support chain, long

11 0 073 * Support chain, short

11 0 074 * Shackle (2)

11 0 080 M Engine mounting plates for securing engine on assembly stand Used together with: 00 1 450Engine: M60, M62

11 0 081 * Mounting plate with adjustment flange

11 0 082 * Mounting plate

11 0 090 M Engine mounting plates for securing engine on assembly stand Used together with: 00 1 450Engine: M40, M42, M43, M44

11 0 100 Adapter for engineUsed together with: 00 1 450Engine: M10

11 0 110 Adapter for diesel engineUsed together with: 00 1 450Engine: M21

11 0 120 Adapter for engineUsed together with: 00 1 450Engine: M20, M30, S38

11 0 130 Adapter for engineUsed together with: 00 1 450Model: 530i Engine: M30 Others: USA only

11 0 180 M Accessories for removing and installing valve springsUsed together with: 11 1 060Engine: M40, M43, M70, M73

11 0 190 M Accessories for removing and installing valve springsUsed together with: 11 1 060Engine: M20, M21, M30, M40, M41, M42, M43, M44, M50, M51, M52, M60,M62, M70, M73, S14, S38, S50B30, S50B32

11 0 191 * Securing bracket and 2 screwsReplaced by 11 0 213Engine: M41, M51

11 0 192 * Guide tubeEngine: All models


11 0 193 * Lever with hook Replaced by 11 0 342, 11 0 343Engine: M51, S50, M60

11 0 194 * Valve spring cageEngine: M41, M51, S50

11 0 200 M Plastic protector for guide of hydraulic valve lash adjusters (12 x)Engine: M41, M51, M60, M62

11 0 210 M Accessories for removing and installing valve springsUsed together with: 11 1 060Engine: M60, M62

11 0 211 * Placement board for cylinder head

11 0 212 * Valve spring cageEngine: M60

11 0 213 * Fastener strap

11 0 214 * HookReplaced by 11 0 343Engine: M60

11 0 220 M Compression measuring kitFor all petrol and diesel enginesEngine: M10, M20, M21, M30, M40, M41, M42, M43, M44, M50, M51, M52,M60, M62, M70, M73, S14, S38, S50B30, S50B32

11 0 221 * Compression recorder for diesel engines

11 0 222 * Test probeUsed together with: 11 0 240For compression recorder 11 0 221 and 11 0 160Engine: M21, M41, M51

11 0 223 * Charts (100)For diesel engine compression recorder

11 0 224 * Compression recorder for petrol engines

11 0 225 * Extension hose For rubber cone with connection piece 11 0 228 / Discontinued

11 0 226 * Test probeUsed together with: 11 0 240For compression recorder 11 0 224 and 11 0 160Engine: M40, M42, M43, M50, M52, M60, M62, M70, M73

11 0 227 * Test probeUsed together with: 11 0 240For compression recorder 11 0 224 and 11 0 160Engine: S14, S38, S50


11 0 228 * Rubber cone with connection pieceUsed together with: 11 0 240For compression recorder 11 0 224 and 11 0 160Engine: M10, M20, M30

11 0 229 * Charts (100)For compression recorder 11 0 224

11 0 230 * Must not be created as a tool number

11 0 232 * CaseWith foam lining for compression recorder

11 0 233 * Check valve

11 0 234 * Filter 3 x 3 mm

11 0 235 * Test probe, screw-inUsed together with: DIS and DIS pressure sensorFor measuring "absolute compression" at all cylinders, Engine: S14, S38, S50B30, S50B32, S50US, S52US

11 0 240 CouplingUsed together with: 11 0 222, 11 0 226, 11 0 227, 11 0 225For adapting test probes to pressure gauge 11 0 162

11 0 310 Cylinder head leakage testerEngine: M43, M44

11 0 311 * Sealing strip Engine: M43

11 0 312 * Sealing stripReplaced by 11 0 318

11 0 313 * Rubber mount (2) Engine: M43

11 0 314 * Cap for water pump connection Engine: M43

11 0 315 * Cover for radiator connection with valveEngine: M43

11 0 316 * Cover for heating connectionUsed together with: 11 1 431, 11 1 433, 11 1 435, 11 1 436, 11 1 439

11 0 317 * Screw plug (2) Engine: M43

11 0 318 * Sealing stripEngine: M43


11 0 340 M Accessories for removing and installing valve springsUsed together with: 11 1 060Engine: M20, M21, M30, M40, M41, M42, M43, M44, M50, M51, M52, M60,M62, M70, M73, S14, S38, S50B30, S50B32

11 0 341 * Valve spring cageEngine: M43, M73

11 0 342 * Pressure leverEngine: all, except M10

11 0 343 * HookEngine: all, except M10

11 0 344 * Valve spring cageEngine: M52


11 1 010 TesterFor leakage testing cylinder headsEngine: M10, M30, S14, S38

11 1 011 * Screws (14)

11 1 012 * Sealing strips (2)

11 1 013 * Rubber mount (2)

11 1 014 * Air connection with reducer Engine: M10

11 1 015 * Cover for branch flangeEngine: M10

11 1 016 * Air connectionEngine: M30


11 1 018 * BridgeEngine: M30

11 1 019 * Reducer


11 1 021 * Sealing strips (2)



11 1 023 * Air connection piece Engine: M20


11 1 025 * Intake pipe connectionEngine: M20

11 1 026 * Connection with air valve for thermostatEngine: M40

11 1 027 * Cover plate for connection duct to water pumpEngine: M40

11 1 028 * Cover plate for radiator flange connectionEngine: M40

11 1 029 * Cover plate for heater connectionEngine: M40

11 1 030 Cylinder head leakage testerEngine: M21

11 1 031 * Sealing strip with rubber mount

11 1 032 * Sealing strip with rubber mount


11 1 034 * Cover for branch flange

11 1 035 * Cover for heater connection

11 1 036 * Air connection

11 1 037 * Screw plugs (2)

11 1 040 Fixture for removing and installing camshaft and valve springsUsed together with: 00 1 450Engine: M10

11 1 041 * Pressure frame

11 1 042 * Threaded spindle with nut (2)

11 1 043 * Clamping bracket

11 1 044 * Pressure spindle

11 1 045 * Lock pins for securing cylinder head placement boardsEngine: All models

11 1 046 * Support frame with guide brackets


11 1 047 * Placement board

11 1 048 * Guide rod

11 1 049 * Pressure lever with hook and valve spring cage

11 1 050 M Accessories for removing and installing valve springsUsed together with: 11 1 060Engine: M20, M30, M50, S14, S38

11 1 051 * Guide bracket, offsetEngine: S38

11 1 052 * Valve spring cageEngine: S14, S38, M50

11 1 053 * Placement boardEngine: S14, S38

11 1 059 * Nuts (4) for pressure frameEngine: M20, M30

11 1 060 M Fixture for removing and installing camshafts and valve springsUsed together with: 00 1 450, 11 0 180, 11 0 190, 11 0 210, 11 0 341,11 1 045, 11 1 050, 11 1 440, 11 3 130, 11 3 410Engine: M20, M21, M30, M40, M41, M42, M43, M44, M50, M51, M52, M60,M62, M70, M73, S14, S38, S50B30, S50B32

11 1 061 * Pressure frameEngine: M20, M30

11 1 062 * Spindle (4) Engine: M20, M30

11 1 063 * Straight pins (4) Engine: M30

11 1 064 * Placement boardEngine: M30

11 1 065 * Support frameEngine: all, except M10

11 1 066 * Placement boardEngine: M20

11 1 067 * Guide rodEngine: all, except M10

11 1 068 * Pressure lever with hookReplaced by 11 0 342 / 11 0 343 Engine: S14, M20, M30, S38, M40,M42, M50, M70



11 1 070 * Not used

11 1 071 * Guide bracket, offset Engine: M20, M30, M42, M44, M50, M52, M60, M62, M70, M73, S14, S38,S50

11 1 072 * Fastener strapEngine: M73

11 1 110 Cylinder head leakage testerUsed together with: 11 1 012Engine: M88, S14, S38

11 1 111 * Cover rail with rubber mount

11 1 112 * Bolts (14)

11 1 113 * Air connection

11 1 130 Drift for mounting valve stem sealsNot for offset valve guidesEngine: M10, M30

11 1 150 Ring spanner for fitted screws on rocker armsUsed together with: 00 2 050Engine: M10, M20, M30, S14, S38

11 1 180 Ring spanner for fitted screws on rocker armsUsed together with: 00 2 050Engine: M21

11 1 200 M Drift for mounting valve stem seatsEngine: M20, M21, M40, M41, M42, M43, M44, M50, M51, M52, M60, M62,M70, M73, S14, S38, S50B30, S50B32

11 1 210 M Extractor for rotary shaft seal in timing case coverUsed together with: 11 2 383Engine: M70, M73

11 1 220 M Installer sleeve for rotary shaft seal in timing case cover (crankshaft, front)Engine: M60, M62, M70, S50B30, S50B32

11 1 230 M Drift for rotary shaft seal in rear crankshaft end coverUsed together with: 00 5 500Engine: M60, M62, M70, M73

11 1 260 M Impact driftUsed together with: 00 5 500For fitting rotary shaft seal in rear crankshaft end coverEngine: M10, M20, M21, M30, M40, M41, M42, M43, M44, M50, M51, M52,S14, S38, S50B30, S50B32

11 1 270 ToolFor fitting radial seal in timing gear coverEngine: M10, M30, M42


11 1 271 * NutEngine: M10

11 1 272 * NutEngine: M30

11 1 273 * Thrust ringEngine: M10, M30, M42

11 1 280 M Impact driftUsed together with: 00 5 500For fitting rotary shaft seal in top of timing case coverModel: 633CSi, 732i Engine: M30, M70, M73

11 1 290 ToolFor holding vent pipeEngine: M20

11 1 300 ToolFor fitting needle bearing in crankcaseEngine: M20

11 1 301 * Drift

11 1 302 * Guide sleeve

11 1 310 DriftFor removing needle bearing from crankcaseEngine: M20

11 1 340 Assembly sleevesFor fitting valve stem seal, diameter 8 mmEngine: M10, M30

11 1 360 M Assembly sleevesFor fitting valve stem seals, diameter 7 mmEngine: M70, M73, S14, S38

11 1 370 ToolFor fitting dipstick guide tube in crankcaseModel year: 80 up to 83Series: E21, E28 Engine: M20

11 1 380 M SleevesFor installing valve stem seals, diameter 7 mmEngine: M20, M21, M40, M42, M43, M50, M51, S50B30, S50B32

11 1 390 DriftFor fitting dipstick guide tubeEngine: M10

11 1 400 FixtureUsed together with: 11 1 421, 11 1 422, 11 1 437For leakage testing cylinder headsEngine: S50B30, S50B32


11 1 401 * Cover plate

11 1 402 * Screws (13)Engine: M10

11 1 403 * End hose (diameter 24 mm) with clipUsed together with: 11 1 437;Use valve from 11 1 437

11 1 410 M Moulded strips for insertion in cylinder head covers to press down timingcase cover on cylinder bank 1...4 and 5...8Engine: M62

11 1 411 * Moulded strip for cylinder bank 1...4

11 1 412 * Moulded strip for cylinder bank 5...8

11 1 420 Cylinder head leakage testerEngine: M70, M73, S50B30, S50B32

11 1 421 * Sealing strip with 7 pins

11 1 422 * Sealing strip with 2 pins

11 1 423 * Cover plate Engine: M70, M73

11 1 424 * Cover plate with valveEngine: M70, M73

11 1 425 * Rubber seals for sealing strips 11 1 421, 11 1 422

11 1 430 Cylinder head leakage testerUsed together with: 11 0 316 (M42, M44), 11 1 450 (M50, M52, S50)Engine: M42, M44, M50, M52, S50B30, S50B32

11 1 431 * Sealing strip with 5 pins and rubber seal Engine: M42, M44, M50, M52

11 1 432 * Rubber seal for sealing strip 11 1 431Engine: M42, M44, M50, M52

11 1 433 * Sealing strip with 7 pins and rubber sealEngine: M42, M44, M50, M52

11 1 434 * Rubber seal for sealing strip 11 1 433Engine: M42, M44, M50, M52

11 1 435 * Formed plate with rubber sealEngine: M42, M44

11 1 436 * Bridge with rubber seal and 2 screwsEngine: M42, M44, M50, M52

11 1 437 * End plug with valve and standard clipEngine: M42, M44, M50, M52, S50


11 1 438 * End plug and standard clipEngine: M42, M44, M50, M52

11 1 439 * Standard partsEngine: M42, M44, M50, M52

11 1 440 M Assembly toolUsed together with: 11 1 060For removing and installing valve springsEngine: M42, M44, M50, M52


11 1 450 Cylinder head leakage testerUsed together with: 11 1 430Engine: M50, M52

11 1 451 * Fastening plate

11 1 452 * Spindle

11 1 453 * O-ring


11 1 461 * Sealing strip with rubber seal (wide version)

11 1 462 * Sealing strip with rubber seal (narrow version)

11 1 463 * Cover for water pump connection

11 1 464 * HoseEngine: M51

11 1 465 * Hose with valveEngine: M51

11 1 466 * Rubber seal for sealing stripsUsed together with: 11 1 461, 11 1 462

11 1 467 * Hose with valveEngine: M41

11 1 468 * Screw plugs (2)


11 1 471 * Sealing strip with rubber seal (wide version)

11 1 472 * Sealing strip with rubber seal (narrow version)Replaced by 11 1 477

11 1 473 * Sealing plate for cylinder bank 1...4


11 1 474 * Sealing plate for cylinder bank 5...8

11 1 475 * Rubber seal for sealing strip 11 1 471

11 1 476 * Rubber seal for sealing stripsUsed together with: 11 1 472; Replaced by 11 1 478

11 1 477 * Sealing strip with rubber seal (narrow version)

11 1 478 * Rubber seal for sealing strip 11 1 477

11 1 480 M Pliers for removing valve stem sealEngine: M40, M41, M42, M43, M44, M50, M51, M52, M60, M62, M70, M73,S38, S50B30, S50B32, S50US, S52US

11 1 960 M Assembly sleeves for fitting valve stem seal, diameter 6 mmEngine: M41, M42, M44, M50, M51, M52, M60, M62

11 2 000 M Puller For removing sprocket from crankshaftEngine: M10, M30, M50, M52, M60, M62, M70, M73, S14, S38

11 2 001 * Bell

11 2 002 * Plate Engine: M10, M30, S14, S38

11 2 003 * SpindleEngine: M10, M30, M70, M73, S14, S38

11 2 004 * Plate Engine: M50, M52, M60, M62

11 2 005 * Spindle 165 mm Engine: M50, M52, M60, M62

11 2 006 * Plate Engine: M70, M73

11 2 010 M Extractor For removing guide bearing in crankshaft, stem diameter 12 mmEngine: M10, M20, M21, M30, M40, M42, M50, M60, M62, S14, S38

11 2 011 * Remover claw I with threaded bushEngine: except M60, M62

11 2 012 * Remover claw IIEngine: except M60, M62

11 2 013 * Pressure spindleEngine: except M60, M62

11 2 014 * SleeveEngine: except M60, M62


11 2 015 * Threaded bushEngine: except M60, M62

11 2 016 * Pressure spindleEngine: M60/B30, M62

11 2 030 M Drift for fitting guide bearing in crankshaftUsed together with: 00 5 500Engine: M10, M20, M21, M30, M40, M42, M50, M52, S14, S38

11 2 040 Holder for releasing and tightening pulley on intermediate shaftEngine: M21

11 2 050 M Guide pins for installing connecting rod with pistonEngine: M21, M70, M73

11 2 060 M Guide pins for installing connecting rod with pistonEngine: S14, S38

11 2 070 M Holder for locking flywheelEngine: M60, M62, M70, M73

11 2 080 M Toothed drive belt tester for checking toothed belt tension when replacingcamshaft drive beltEngine: M40

11 2 100 Holder for locking flywheel with transmission installedEngine: M10Transmission: 3 HP 12, 3 HP 22

11 2 120 Holder for locking flywheel with transmission installedEngine: M30Transmission: 3 HP 20, 3 HP 22, 4 HP 22

11 2 130 Spindle for removing hub and toothed belt gearwheel from crankshaftUsed together with: 00 7 501Engine: M20

11 2 131 * Spindle with M6 thread

11 2 132 * Spindle with M8 thread

11 2 133 * Knurled nut

11 2 140 Holder for locking flywheel with transmission removedEngine: M10

11 2 150 M Holder for locking crankshaft when releasing and tightening central boltEngine: M20, M40, M41, M43, M44, M50, M51, M52

11 2 160 M Holder for locking flywheel with transmission removedEngine: M10, M30, S14, S38


11 2 170 M Holder for locking flywheelEngine: M20, M21, M40, M41, M42, M43, M44, M50, M51, M52, S50B30,S50B32

11 2 180 Socket wrench socket WAF 36 for releasing and tightening vibration damperon crankshaftEngine: M30

11 2 190 Holder for locking camshaft and intermediate shaftEngine: M20

11 2 191 * Bracket

11 2 192 * Bolts (2)

11 2 210 M Slip bush for preventing damage to rotary shaft seal during assemblyEngine: M10, M20, M21, M30, M40, M41, M42, M43, M44, M50, M51, M52,S14, S38, S50B30, S50B32

11 2 211 * Slip bush for crankshaft (front)Engine: M20, S50

11 2 212 * Slip bush for intermediate shaft and camshaftEngine: M20, M21

11 2 213 * Slip bush for crankshaft end cover (rear)

11 2 230 M Holder for locking vibration damper when releasing and tightening centralboltEngine: M70

11 2 240 M Holder for locking hub when releasing and tightening central boltSeries: E32, E34Model: M5 Engine: M30, S38

11 2 250 M Torx socket E12 with 1/2" extension piece for releasing and tighteningcylinder head boltsEngine: M42, M43, M44, M50, M52, M60, M62

11 2 260 M Piston ring tensioner to compress piston rings when fitting in pistonEngine: M60, S14, S38

11 2 270 M Piston ring tensioner to compress piston rings when fitting in pistonEngine: S14, S38

11 2 280 Holder for locking toothed belt gearwheel on intermediate shaftModel year: as from 87Engine: M20

11 2 290 Placement board for piston with connecting rodEngine: M10, M20, M21, M30, M40, M41, M42, M43, M44, M50, M51, M52,M60, M62, M70, M73, M88, S14, S38, S50B30, S50B32


11 2 300 M Lock pin for locating crankshaft in ignition TDC position in order to adjustvalve timingEngine: M21, M40, M41, M42, M43, M44, M50, M51, M52, M60, M62, M70,M73, S50B30, S50B32

11 2 310 M ExtractorFor removing rotary shaft seal in lower timing case coverEngine: M40, M42, M43, M44

11 2 311 * Extractor

11 2 312 * Pressure pieceReplaced by 11 2 313Engine: M40

11 2 313 * Pressure pieceEngine: M42, M43, M44

11 2 314 * Spindle M12x150

11 2 320 M Sleeve for installing rotary shaft seal in lower timing case cover (crankshaftfront)Engine: M40

11 2 330 M Assembly plate for timing gear case cover without removal of cylinder head(M42, M43, M44) and for installing upper timing gear case cover (M43, M44)Engine: M42, M43, M44

11 2 340 M Extractor for guide bearing in crankshaft, stem diameter 15 mmUsed together with: 11 2 016 (M60, M62)Engine: M41, M42, M43, M44, M50, M51, M52, M60, M62, M70, M73,S50B30, S50B32

11 2 341 * Remover claw with threaded bush

11 2 342 * Remover claw


11 2 344 * Sleeve

11 2 350 M Drift for installing guide bearing in crankshaftEngine: M41, M42, M43, M44, M50, M51, M52, M60, M62, M70, M73,S50B30, S50B32

11 2 360 M WAF 50 socket wrench socket for releasing and tightening bearing pin forbelt tensionerEngine: M41, M51

11 2 370 M Bracket for fixing engine in position when installing or removing transmissionEngine: M51

11 2 380 M Tool For removing rotary shaft seal in timing case coverEngine: M41, M50, M51, M52, M60, M62, S50B30, S50B32


11 2 381 * Thread bell

11 2 382 * Spindle

11 2 383 * Pressure pieceEngine: M41, M50, M51, M52, M60, M62

11 2 384 * Pressure pieceEngine: S50

11 2 385 * Spacer bushEngine: M41, M50, M51, M52

11 2 390 M Slip bush for preventing damage to rotary shaft seal when assembling rearend coverEngine: M60, M62, M70, M73

11 2 400 M Tensioning bracket for fitting chain tensioner with timing case cover removedUsed together with: 11 3 390Engine: M60

11 2 410 M Spacer for holder used to lock crankshaft in position when releasing andtightening central boltUsed together with: 11 2 150Engine: M41, M44, M52

11 2 420 M Holder for locking vibration damper when releasing and tightening centralboltEngine: M73

11 2 430 M Gauge for checking camshaft setting for removing and installing camshaftsEngine: M60

11 2 440 M Locking fixture for fixing camshaft in position when adjusting valve timingEngine: M60, M62

11 2 441 * Gauge for inlet side 1...4

11 2 442 * Gauge for inlet side 5...8

11 2 443 * Fastening plate (2)

11 2 444 * Special screw (2)

11 2 445 * Gauge for exhaust side 1...4 (reference value 3.5ø)

11 2 446 * Gauge for exhaust side 5...8 (reference value 3.5ø)

11 2 450 M Holder for locking hub when releasing and tightening central boltSeries: E31, E32, E34, E38, E39 Engine: M60, M62

11 2 470 M Guide drift (2) for installing connecting rod with pistonEngine: M40, M41, M43, M60, M62


11 2 480 M Spacer for supporting engine when removing and installing transmissionSeries: E32, E34 Engine: M60

11 2 490 M Holder for locking vibration damper when releasing and tightening centralboltEngine: S50B30, S50B32

11 3 010 M Tool for evenly pressing down camshaft when releasing and tighteningcamshaft bearing capsEngine: S14, S38

11 3 020 Fixture for turning camshaft and crankshaft when adjusting valvesEngine: S14, S38

11 3 030 Placement board for tappetsEngine: M10, M20, M21, M30, M40, M41, M42, M43, M44, M50, M51, M52,M60, M62, M70, M73, M88, S14, S38, S50B30, S50B32

11 3 040 Screw unit for removing the deflection wheel and guide railUsed together with: 11 3 062Engine: M88, S14, S38

11 3 041 * Drift for deflection wheel

11 3 042 * Adapter for guide rail

11 3 050 Drift for rocker arm shaftEngine: M10, M20, M30

11 3 060 Extractor for rocker arm shaftsEngine: M30

11 3 061 * Shaft

11 3 062 * Impact bush

11 3 063 * Thrust washer

11 3 070 Hook for adjusting valvesEngine: M10, M20, M30

11 3 080 M Drift for installing rotary shaft seal on camshaftEngine: M21

11 3 090 Device for adjusting camshaftEngine: M21

11 3 091 * Locking fixture with inserts

11 3 092 * Claw A

11 3 093 * Claw B

11 3 094 * Spindle with nut


11 3 100 FixtureFor turning over engine with twin timing chainEngine: M10, M30

11 3 101 * Driver claws (2)


11 3 110 Engine cranking fixture (single timing chain)Engine: M10, M30

11 3 111 * Handle

11 3 112 * Jaw with grooveEngine: M10

11 3 113 * Jaw without grooveEngine: M10

11 3 114 * Jaw with grooveEngine: M30

11 3 115 * Jaw without grooveEngine: M30


11 3 120 Lever for removing and installing rocker armsEngine: M21

11 3 121 * Handle

11 3 122 * Cage

11 3 130 M Assembly toolUsed together with: 11 1 060For removing and installing valve springsEngine: M21, M40, M41, M43, M47, M51

11 3 131 * Guide bracket, straight (2)

11 3 132 * Placement boardEngine: M21, M41, M51

11 3 133 * Pressure lever with hookReplaced by 11 0 342, 11 0 343 / Engine: M21


11 3 135 * Fastening boltEngine: M21

11 3 140 Extractor for removing ball pins in cylinder headEngine: M21


11 3 141 * Sleeve

11 3 142 * Extractor spindle

11 3 143 * Nut

11 3 150 Holder for pressing down bucket tappets when removing and installing valveadjustment platesModels without catalytic converterModel: 635CSi Engine: M88, S38

11 3 160 M Support with 5 feeler gauges for setting valvesEngine: M88, S14, S38

11 3 161 * Bracket

11 3 162 * Feeler gauges 0.25/0.30/0.35/0.40/0.45 mm (5)

11 3 170 M Lever for pressing down bucket tappets when removing and installing valveadjustment platesModels with catalytic converterEngine: S14, S38

11 3 180 M Lever for pressing down valves when removing and installing rocker armsEngine: M40, M70

11 3 190 M Locking fixture for fixing camshaft in position when adjusting valve timingEngine: M40, M43, M70, M73

11 3 200 M Drift for fitting rotary shaft seal in top of timing case coverUsed together with: 00 5 500Engine: M70, M73

11 3 210 M Centring sleeve for installing upper timing case cover on camshaftUsed together with: 11 3 220Engine: M70

11 3 220 M Sliding bush for installing upper timing case cover on camshaftUsed together with: 11 3 210Engine: M70, M73

11 3 230 M Protractor disc for mounting on vibration damper when tightening central boltwith rotation angle methodEngine: S38

11 3 240 M Locking fixture For fixing camshaft in position when adjusting valve timingEngine: M42, M44, M50, M52

11 3 241 * Gauge for inlet side

11 3 242 * Gauge for exhaust side

11 3 243 * Securing bracketReplaced by 11 3 244 with launch of M52TU


11 3 250 M Cylinder head tappet suckerEngine: M40, M41, M42, M43, M44, M50, M51, M52, M60, M62

11 3 251 * Sucker (8)

11 3 252 * Storage box

11 3 260 M Fixture for uniformly pressing down camshaft (with bearing cap) whenreleasing and tightening camshaft bearing cap Engine: M42, M50, M52, S50US, S52US

11 3 261 * Assembly fixture

11 3 262 * Fastener bolt (2)

11 3 270 M Fixture for uniformly pressing down camshaft (with bearing cap) whenreleasing and tightening camshaft bearing cap Used together with: 11 3 260Engine: M50


11 3 272 * Fastener bolt

11 3 280 M Bush for installing rotary shaft seal in lower timing case coverEngine: M50, M51, M52, S50B30, S50B32

11 3 290 M Set up lock pins for secondary chain tensioner to block chain tensioner pistone.g. when removing and installing sprocketsEngine: M50, M52

11 3 291 * Lock pin clipsEngine: M50

11 3 292 * Lock pinEngine: M52

11 3 310 M Lock pin clips for secondary chain tensioner (2) to block chain tensionerpiston, e.g. when removing and installing sprocketsEngine: M62

11 3 320 M Fixture for locking camshaft when adjusting valve timing

11 3 330 M Fixture for uniformly pressing down camshaft (with bearing cap) whenreleasing and tightening camshaft bearing cap Engine: M51

11 3 340 M Lock pin (2) for locking chain tensioner piston in position (e.g. whenremoving and installing cylinder head) as well as for locking drive belttensionerEngine: M41, M43, M44, M51

11 3 360 M Fixture for pressing in chain tensioner piston when locking and unlockingchain tensionerEngine: M41, M51


11 3 380 M Torx screwdriver socket T50 For releasing and tightening dual massflywheel (ZMS)Model year: Up to 12/93Engine: M60, M70

11 3 390 M Chain tensioner for tensioning primary chain when adjusting valve timingEngine: M50, M60, M62

11 3 391 * Sleeve

11 3 392 * Spindle

11 3 400 M Fixture for uniformly pressing down camshaft when releasing and tighteningcamshaft bearing cap Engine: S50B30, S50B32


11 3 402 * Fastener bolts (3)

11 3 410 M Accessories for removing and installing valve springsUsed together with: 11 1 060Engine: S50B30, S50B32


11 3 412 * Bolts (2)

11 3 413 * HookReplaced by 11 0 343

11 3 420 M Lock pin clips for secondary chain tensioner (2) to block chain tensionerpiston, e.g. when removing and installing sprocketsEngine: M60

11 3 430 M Fixture for turning installed camshaft to removal positionEngine: M60, M62

11 3 440 M Locking fixture for vibration damper 45ø- before TDC position when installingcylinder head (this prevents valves making contact with piston)Engine: M60

11 3 450 M Compressed air connection for checking VANOS adjustment unitUsed together with: 12 6 410Engine: M50, M52

11 3 460 M Protractor for fitting on counterholder 11 2 450 when torquing centre boltUsed together with: 11 2 450Engine: M60, M62, M73

11 3 470 M Screwdriver hexagon socket WAF 5/3/8" connection, stem length 60 mm,for releasing and tightening sprockets on camshaftEngine: S50B30, S50B32


11 3 480 M Guide pin for installing connecting rod with piston (2)Engine: M44, S50B30, S50B32

11 3 490 M Reference gauge for adjusting timing diagram when installing VANOS unitEngine: S50B30, S50B32

11 4 020 Wrench for oil filter cartridgesSeries: All models, not 4-wheel driveEngine: M10, M20

11 4 030 Adapter for pressure gauge for testing oil pressureUsed together with: BMW SERVICE TESTEREngine: M10, M20, M21, M30, M50, M51, M52, M60, M62, M70, M73, S14,S38, S50B30, S50B32

11 4 040 Screw for bleeding oil circuit on all engines with return valve in upper sectionof oil filter housingEngine: M30, M30B34, M30Tur

11 4 050 M Reducer for connecting pipe elbow 13 6 054 to pressure gauge13 3 061 or BMW DIS for checking oil pressureUsed together with: 13 3 063 or 13 6 051Engine: M10, M20, M21, M30, M50, M51, M52, M60, M62, M70, M73, S14,S38, S50B30, S50B32

11 4 070 M Fixture for installing oil dipstick guide tubeEngine: M10, M88, S38

11 4 090 Fixture for installing oil dipstick guide tubeEngine: S14

11 4 110 M Pin (4) for fixing metal gasket on upper timing case cover during assemblyEngine: M43, M44

11 4 120 M Lock pin for chain tensioner to lock chain tensioner piston in position (e.g.when removing and installing cylinder head)Engine: M43

11 4 130 M Lever for pressing down valves when removing and installing rocker armsEngine: M43, M73

11 4 140 M Bush for installing chain tensioner pistonEngine: M43

11 4 150 M Bush for fitting radial shaft seal in lower timing case coverUsed together with: Central crankshaft boltEngine: M43, M44

11 4 160 M Pressure gauge adapter 13 3 061 or BMW DIS for checking oil pressureUsed together with: 13 3 063 or 13 6 051Engine: M41

11 4 170 M Pressure gauge adapter 13 3 061 or BMW DIS for checking oil pressureUsed together with: 13 3 063 or 13 6 051; model year: up to 08/95Engine: M40, M42, M43


11 4 180 M Torx screwdriver socket T60 For releasing and tightening dual massflywheel (ZMS)Model year: As from January 94Engine: M60, M62

11 4 190 M 1/4" extension piece for removing and installing pedal position sensorSeries: E31, E38 Engine: M73

11 4 200 M Fixture for centring oil pump with respect to crankshaft during assemblyEngine: M41, M51

11 4 201 * Centring bush

11 4 202 * Thrust washer

11 4 203 * Spindle

11 4 210 M Bush for fitting radial shaft seal for crankshaft in timing case coverUsed together with: Central crankshaft boltEngine: M41, M51

11 4 220 M Chain tensioner for tensioning primary chain when adjusting valve timingUsed together with: 00 9 250Engine: M52

11 4 650 Oil filter wrenchSeries: E30Model: 325ix Engine: M20

11 5 010 Clamp for toothed belt tensioner when removing water pumpEngine: M20

11 5 011 * Clamping piece

11 5 012 * Screw

11 5 020 Tester for V-belt tension With German scaleEngine: M10, M20, M21, M30, M40, S14, S38

11 5 021 * Tester for V-belt tension With English scale

11 5 022 * Tester for V-belt tension With French scale

11 5 023 * Tester for V-belt tension With Dutch scale

11 5 024 * Tester for V-belt tension With Swedish scale

11 5 025 * Tester for V-belt tension With Italian scale


11 5 026 * Tester for V-belt tension With Spanish scale

11 5 027 * Scale in specific language, singleSpecify language required

11 5 028 * Test rod

11 5 029 * Pointer

11 5 030 M Holder For pulley on water pump when releasing and tightening fanModel year: as of 80Engine: M10, M20, M21, M30, M50, M51, M52, M70, M73, S14, S38,S50B30, S50B32

11 5 040 M Open-ended spanner WAF 32 for releasing and tightening fan wheelUsed together with: Torque wrench 3/8" connectionEngine: M10, M20, M21, M30, M40, M41, M42, M43, M44, M50, M51, M52,M60, M62, M70, M73, M88, S14, S38, S50B30, S50B32, S50US, S52US

11 5 050 M Holder for pulley when releasing and tightening fanEngine: M40, M41, M42, M43, M44, M60, M62

11 5 060 Temperature measuring kit for measuring cylinder head temperature whenreplacing toothed drive beltEngine: M40

11 5 061 * Hand-held thermometer

11 5 062 * Surface sensor

11 5 069 * Handbook

11 5 070 M Lever for pressing down bucket tappets when removing and installing valveadjustment platesEngine: S50B30, S50B32

11 5 080 M Locking fixture for fixing camshaft in position when adjusting valve timingEngine: S50B30, S50B32

11 5 090 M Fixture for fitting radial shaft seal for crankshaft in timing case coverUsed together with: 11 1 220Engine: S50B30, S50B32

11 5 100 M Fixture for cranking engine at crankshaft when adjusting valve timingEngine: S50B30, S50B32

11 5 110 M Bush for fitting rotary shaft seal on crankshaft in timing case coverEngine: M73

11 5 130 M Lever for pressing down valves when removing and installing rocker armsEngine: M44

11 5 131 * Lever


11 5 132 * Pressure cage

11 5 133 * Spring

11 5 490 M Tool for turning sprockets when removing and installing VANOS unitEngine: M50, M52, S50US, S52US

11 6 010 Pin wrench for ring nut on exhaust manifoldModel: 745i Engine: M30

11 6 030 Ring spanner for exhaust manifoldUsed together with: 00 2 050Model: 745i Engine: M30

11 6 050 Socket wrench socket, 12-sided, WAF 10Model: 745i Engine: M30

11 6 060 M Extension piece (400 mm long with magnet) for removing and installingintake pipeEngine: M70, M73

11 6 070 M Socket wrench socket with joint WAF 9 for releasing and tightening exhaustnutsSeries: E34 Engine: S38

11 7 000 Open ring spanner WAF 24 for exhaust gas recirculation valveModel: 530iUS Engine: M30

11 7 010 Formed hose for testing control valveUsed together with: 17 0 000Engine: M21

11 7 020 M Socket wrench socket WAF 22 for releasing and tightening oxygen sensorEngine: M10, M20, M30, M40, M42, M50, M60, M70, M73, S14, S38,S50B30, S50B32, S50US, S52US

11 7 030 M Socket wrench socket WAF 22 for releasing and tightening oxygen sensorEngine: M43, M44, M52, M62

11 7 100 Multipurpose cylinder head clamping device for installing and removingvalvesEngine: All models

11 7 300 Placement board for valves, valve springs, hydraulic tappets, rocker arms,etc.Engine: M10, M20, M21, M30, M40, M41, M42, M43, M44, M50, M51, M52,M60, M62, M70, M73, M88, S14, S38, S50B30, S50B32, S50US, S52US

11 7 310 M Spacer for supporting engine when removing and installing transmissionSeries: E38, E39 Engine: M62, M73

11 7 320 M Gauge (8ø) for setting hook nozzles in crankcase during assemblyEngine: M44


11 7 330 M Test connection and modified oil filter wrench for pressure gauge13 3 061 or BMW DIS for measuring oil pressureUsed together with: 13 3 063 or 13 6 051Engine: M43, M44

11 7 331 * Oil filter wrench

11 7 332 * Oil filter cover incl. M12 connection thread

11 7 333 * Central rod

11 7 340 M Gauge (1.5ø) for setting camshaft reference angle (timing diagram) wheninstalling VANOS unitUsed together with: 11 7 350 and 12 6 412Engine: S50B32

11 7 341 * 1.5ø gauge (basic body)

11 7 342 * Lock pin

11 7 350 M Compressed air connector for charging VANOS unit with compressed airduring assemblyUsed together with: 11 7 340 and 12 6 412Engine: S50B32

11 7 360 M Spacer for supporting engine when removing and installing transmissionSeries: E38 Engine: M51, M52

11 7 370 M Spacer for supporting engine when removing and installing transmissionSeries: E39 Engine: M51, M52

11 7 380 M Clamping bracket for fitting chain tensioner with upper right timing casecover removed Used together with: 11 3 390Engine: M62

11 7 450 M Simulator for Bosch oxygen sensorUsed together with: Standard workshop emission testerEngine: M10, M20, M30, M40, M42, M43, M44, M50, M52, M60, M62, M70,M73, S14, S38, S50B30, S50B32, S50US, S52US

11 7 451 * Simulator (control unit)

11 7 452 * 4 pin connecting cable, A coded (connection to wiring harness and oxygensensor)Engine: M40, M42, M43, M50, M70

11 7 453 * 4-pin connector, B coded (connection to oxygen sensor) Engine: S50/B30

11 7 454 * 4 pin connector, B coded (connection to wiring harness)Engine: S50/B30


11 7 455 * 1-pin and 3/4-pin connector (connection to oxygen sensor with Bosch orCannon plug connection)Engine: M10, M20, M30, S14

11 7 456 * 1-pin and 3/4-pin connector (connection to wiring harness with Bosch orCannon plug connection)Engine: M10, M20, M30, S14

11 7 458 * Plug-in jumper

11 7 459 * Handbook

11 8 020 M Device for fixing engine in position when removing and installingtransmissionSeries: E36Model: Z3 Engine: M51, M52, S50B30, S50B32

11 8 021 * Engine locator fixture, front, S50/B30 engine

11 8 022 * Engine locator fixture, rear

11 8 040 M Engine mounting plate for securing engine on assembly stand Used together with: 00 1 450Engine: M41, M50, M51, M52, S50B30, S50B32

11 9 100 Test bottle with hose for checking cooling system for gas leaksEngine: M21


Engine electrical system

Explanation:




12 1 070 RPM booster for setting ignition (L-Jetronic)Engine: M30

12 1 080 M Ignition cable repair kit for fitting spark plug connectors on ignition leadsSeries: E36, E38

12 1 081 * Pliers

12 1 082 * Replacement jawsReplaced by 12 1 083

12 1 083 * Set of dies (cable 4 mm² / ignition cable)

12 1 086 * Assembly sleeve

12 1 087 * Finger guard

12 1 088 * Lubricant

12 1 089 * Handbook

12 1 100 Pressure testing fork for vacuum hose on vacuum cells of ignition distributorand on carburetorEngine: M10, M30

12 1 150 Mounting fixture for locating distributor when removing cotter on distributorpinionModel: 320i, 323i, 520i Engine: M20

12 1 160 M Spark plug spanner WAF 17.5 mm Used together with: 12 1 172For loosening and tightening spark plugsEngine: S14, S38

12 1 170 M Spark plug spanner WAF 16 and torque limiter Used together with: 12 1 200For releasing spark plugs as well as for tightening to torque limitEngine: M40, M42, M43, M44, M50, M52, M60, M62, M70, M73, S14, S38,S50B30, S50B32


12 1 171 * M Spark plug spanner WAF 16 mm Used together with: 12 1 172 (S50), 12 1 200 (M40, M42, M43, M44,M50, M52, M60, M62, M70, M73)Engine: M40, M42, M43, M44, M50, M52, M60, M62, M70, M73

12 1 172 * M Torque limiter 23 Nm ±3 NmUsed together with: 12 1 160 (S14, S38), 12 1 171 (S50)Engine: S14, S38, S50B30, S50B32

12 1 180 M Pliers For removing spark plug connectorsEngine: M10, M20, S14

12 1 200 M Torque limiter 30 Nm for tightening spark plugs to specific torque limitUsed together with: 12 1 171Engine: M40, M42, M43, M44, M50, M52, M60, M62, M70, M73

12 1 400 TDC sensorEngine: M10

12 1 450 Ignition retarder simulator for checking shift functionsEngine: M10 Others: USA only

12 1 460 Ignition retarder simulatorSeries: E28, E30 Engine: M10 Others: Japan only, USA only

12 2 100 M Socket wrench socket WAF 12 for removing and installing heater plugsEngine: M21, M41, M51

12 3 000 Ring spanner (holder) for alternator pulleySeries: E12, E21, E28 Engine: M10, M20, M21, M30

12 4 010 Lock pin for adjusting PCB switch on DME control unitEngine: M30

12 6 400 Mixture control unit (integrator) for checking mixture (lambda = 1)Series: E28, E30 Engine: M10 Others: Japan only, USA only

12 6 410 M Adapter lead and adapter to externally activate VANOS unit duringinstallation and for checking function of 4/2-way valveEngine: M50, M52, S50B32

12 6 411 * Adapter lead with diodeFor non-interchangeable connection to 12 Volt power source Engine: M50,M52

12 6 412 * Adapter (switchbox with cable connection)Engine: S50B32

12 7 010 M Test kit for EML, for checking EML safety pathSeries: E31, E32, E34 Engine: M30, M70

12 7 011 * EML adapter for checking EML safety path on 20-pin engine connector

12 7 012 * 25-pin adapter lead (A-coded)


12 7 013 * 25-pin adapter lead for checking EML safety path (B-coded)Series: E31Engine: M70

12 7 019 * Handbook

12 7 020 M Adapter for primary voltage testing with static high voltage distributionEngine: M42, M50, M52, M60

12 7 029 * Handbook

12 7 030 Adapter for secondary voltage testing with static high voltage distributionEngine: M50, M60

12 7 039 * Handbook

12 7 040 M Set of adapters for checking secondary voltage with static high voltagedistributionEngine: M42, M43, M44, M50, M52, M60, M62

12 7 041 * Single adapters (8)

12 7 042 * Connection cable for BMW SERVICE TESTER

12 7 043 * Set of connection cable (consisting of 7 individual leads)

12 7 045 * Set of clamps (8 clamps) for compact ignition coilsEngine: M43, M44

12 7 049 * Handbook

12 7 100 Gauge for pedal position sensorModel: 324td Engine: M21

12 7 110 M Socket wrench socket WAF 24 for removing and installing alternator pulleyEngine: M40, M41, M42, M43, M44, M50, M51, M52, M60, M62, M70, M73,S50B30, S50B32

12 7 130 M Extension piece 3/8" (2) for removing and installing spark plugsUsed together with: 12 1 172, 12 1 200Series: E31, E38 Engine: M73

12 7 131 * Extension piece, long

12 7 132 * Extension piece, short

12 8 000 56-pin test adapter for checking engine wiring harness on CNG vehiclesUsed together with: 61 1 459Model: 316g

12 8 010 CNG wiring harness plug-in adapter for depressurizing CNG systemModel: 316g


Cooling system

Explanation:




17 0 000 M Tester Fr checking cooling system for leaks and function of pressure relief valve inradiator capSeries: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

17 0 001 * Adapter For checking pressure relief valve in radiator cap Series: all, except E28

17 0 002 * Tester without adapter Pressure range 0...2.5 bar / Series: all, except E28

17 0 003 * Screw connection piece For radiator screw caps (standard thread) / Series: E28, E30, E31, E32Engine: all, except M51

17 0 004 * Adapter For radiator screw caps (standard thread) / Series: E28, E30, E32Engine: M51

17 0 005 * Screw connection piece For radiator screw cap (buttress thread) / Series: E31, E32, E34, E36, E38,E39

17 0 006 * AdapterFor radiator screw cap (butters thread) / Replaced 06/97 by 17 0 007 /Reason: Design modification to expansion tank breather cap

17 0 007 * Adapter For checking expansion tank breather cap / Series: E31, E32, E34, E36, E38,E39

17 0 009 * Adapter for coolant expansion tank Series: E36 /Model: M3 USA

17 0 010 Tester repair kit 17 0 002 Series: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

17 0 011 * Pressure gauge

17 0 012 * Clips (2)


17 0 013 * Mounting socket

17 0 014 * Diaphragm

17 0 015 * Handle

17 0 016 * Threaded rod with 2 nuts and 2 washers

17 0 017 * Leather sleeve

17 0 018 * Cylinder

17 0 019 * Rubber seal

17 0 020 Tester conversion kit 17 0 002 (extension of pressure range from 1.6 barto 2.5 bar)Series: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

17 2 010 Set of adapters for oil delivery units for flushing automatic transmission oilcoolersTransmission: A4S 310R, A5S 300J, A5S 310Z, A5S 440Z, A5S 560Z

17 2 011 * Adapter for connecting oil cooler lines to oil delivery unitUsed together with: 17 2 015, 17 2 016, 17 2 017, 17 2 018, 17 2 019;Transmission: A5S 310Z, A5S 560Z

17 2 012 * Adapter (2 ) for connecting oil cooler lines to oil delivery unitUsed together with: 17 2 015, 17 2 016, 17 2 017, 17 2 01, 17 2 018,17 2 019; Transmission: A4S 310 R

17 2 013 * Banjo bolt with M18x1.5 nut and seal (2) for connecting oil cooler lines to oildelivery unitUsed together with: 17 2 012, 17 2 015, 17 2 016, 17 2 017, 17 2 018,17 2 019; Transmission A5S 440Z

17 2 014 * Banjo bolt with M16x1.5 nut, seal (2) and threaded coupling for connecting oilcooler lines to oil delivery unitUsed together with: 17 2 012, 17 2 015, 17 2 016, 17 2 017, 17 2 018,17 2 019; Transmission A5S 300 J

17 2 015 * Connector for Tecalemit oil delivery unit

17 2 016 * Connector for Horn oil delivery unit

17 2 017 * Coupling (2)

17 2 018 * Hose, long

17 2 019 * Hose, short


Clutch

Explanation:




21 2 060 M Gauge For checking lining thickness on clutch disc on vehicles with internal clutchoperating systemEngine: M10, M20, M21, M30, S14, S38Transmission: 240/5, 242/4, 245/5, 245/5 Sport, 260/5, 262/4, 265/5, 265/5Sport, 280/5 Sport, S5D 250G, S5D 260Z, ZF S5-16

21 2 080 M Gauge for checking lining thickness on clutch discModel year: as of 8/95Engine: M40, M41, M42, M43, M44, M50, M52, M60, M62, M70, M73Transmission: S5D 200G, S5D 250G, S5D 260Z, S5D 310Z, S6S 420G, S6S560G

21 2 081 * Gauge

21 2 082 * Guide plate

21 2 100 M Drift for centring drive disc when installing clutchTransmission: 240/5, 260/5, 265/5, 265/5 Sport, 280/5 Sport

21 2 120 M Drift for centring drive disc when installing clutchTransmission: S6S 420G, S6S 560G

21 2 130 M Drift for centring drive disc when installing clutchTransmission: S5D 200G, S5D 250G, S5D 260Z, S5D 310Z

21 2 140 M Clutch centring pin (2) for centring driver disc on flywheel when installingself-adjusting clutch (SAC)Phase-in of SAC in E46, 09/97 Transmission: S5D 200G, S5D 250G, S5D 260Z, S5D 310Z, S6S 420G, S6S560G

21 2 141 * Clutch centring pin with M10 screwTransmission: S6S 420G, S6S 560G

21 2 142 * Clutch centring pin with M10 screwTransmission: S5D 200G, S5D 250G, S5D 260Z, S5D 310Z

21 2 150 M Clamping fixture for resetting adjustment ring and installing self adjustingclutch (SAC) on flywheel without tensionSelf Adjusting ClutchTransmission: S5D 200G, S5D 250G, S5D 260Z, S5D 310Z, S6S 420G, S6S560G


Manual transmission

Explanation:




23 0 000 Lifter for hoist for removing and installing manual and automatictransmissionsTransmission: Getrag/ZF

23 0 020 M Holder for all 3-hole and 4-hole flanges for releasing and tighteningoperationsTransmission: 265/5, Getrag/ZF

23 0 030 Support for Getrag transmissionTransmission: 280/5 Sport

23 0 040 M Take-up support for removing and installing transmissionUsed together with: 00 2 030 (not included in minimum kit)Transmission: S6S 420G, S6S 560G

23 0 041 * Mounting cage Transmission: S6S 560G

23 0 042 * Transmission support bracketTransmission: S6S 420G

23 0 050 Take-up support for all 4-speed and 5-speed transmissionsUsed together with: 00 1 450Transmission: 242/4

23 0 060 Take-up support for Getrag transmissionsUsed together with: 00 1 450Transmission: 245/5, 245/5 Sport

23 0 070 Take-up bracket for Getrag transmissionsUsed together with: 00 1 450Transmission: 265/5, 265/5 Sport

23 0 080 Fixture for removing 5th gearwheelTransmission: 265/5, 265/5 Sport, 280/5 Sport

23 0 081 * Removal jaws (2)

23 0 090 Take-up support for all ZF and Getrag transmissionsUsed together with: 00 1 450Transmission: 240/5, 260/5, ZF S5-16


23 0 100 M Mounting fixture for securing transmission on assembly stand Used together with: 00 1 450Transmission: S5D 200G, S5D 310Z

23 0 150 Take-up support for ZF transmissionsUsed together with: 00 1 450Transmission: ZF S5-16

23 0 160 Take-up support for Getrag transmissionsUsed together with: 00 1 450Transmission: 262/4

23 0 490 Extractor for removing rotary shaft seal on input shaftTransmission: S5D 200G, S5D 250G, S5D 260Z, S5D 310Z, S6S 420G, S6S560G

23 0 491 * Rod with self-tapping screw

23 0 492 * Weight

23 1 000 Fixture For fitting transmission housing and deep groove ball bearing on to inputshaft and in transmission housingTransmission: 240/5, 242/4, 245/5, 245/5Sport, 260/5, 262/4, 265/5,265/5Sport, 280/5Sport, 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24,A4S 270R, A4S 310R, A5S 300J, A5S 310Z, A5S 440Z, A5S 560Z, BW 65,Getrag/ZF, S5D 260Z, ZF S5-16

23 1 001 * Sleeve

23 1 002 * Dowel pin (2)

23 1 003 * Pressure piece, long

23 1 004 * Pressure piece, short

23 1 005 * Handle

23 1 006 * Dowels for Getrag transmissionTransmission: 245/5, 245/5 Sport

23 1 007 * Pressure piece for Getrag transmissionTransmission: 260/5

23 1 010 Fixture for removing rear section of transmission housingTransmission: 280/5 Sport

23 1 020 Fixture for removing transmission housing (front and rear sections)Used together with: 33 1 301Transmission: 245/5 Sport

23 1 030 Drift for fitting inner bearing race on countershaftTransmission: 245/5, 265/5


23 1 040 Drift for installing slider (5th gear)Transmission: 245/5 Sport, S5D 200G

23 1 050 Puller (Kukko) for 5th gearwheel and reverse gearwheelTransmission: 240/5, 245/5, 260/5, 265/5 Sport, 280/5 Sport, ZF S5-16

23 1 051 * Link (Kukko 20-20)

23 1 052 * Spindle, long (390 mm)

23 1 053 * Arm, long (Kukko 2/300)

23 1 054 * Arm, short (Kukko 2/150)

23 1 060 Puller for removing inner bearing race (reverse gearwheel)Used together with: 33 1 301Transmission: 245/5, 265/5 Sport

23 1 061 * Shells (2)

23 1 062 * Threaded ring

23 1 063 * Sleeve

23 1 070 Measuring ring for determining fitted shim between outer bearing race andcirclip on countershaftTransmission: 245/5

23 1 080 Impact drift for removing and installing outer bearing race in front section oftransmission housing/centre section of countershaft and ball bearing in rearsection of transmission housing for input shaftUsed together with: 00 5 500Transmission: 245/5, 265/5

23 1 090 Impact drift for removing and installing outer bearing race of input shaft infront section of transmission housingUsed together with: 00 5 500Transmission: 245/5, 265/5

23 1 100 Puller claw for speedometer gearUsed together with: 00 7 500Transmission: 245/5, 265/5, 280/5 Sport

23 1 110 Impact drift for fitting bearing of output shaft in rear section of transmissionhousingUsed together with: 00 5 500Transmission: 245/5

23 1 120 Impact drift for removing outer bearing race in centre section of housing forcountershaftUsed together with: 00 5 500Transmission: 240/5, 245/5, 260/5, 280/5 Sport, ZF S5-16


23 1 130 Impact drift for removing input shaft bearing and roller bearing in centresection of transmission housingTransmission: 245/5, 280/5 Sport

23 1 140 Puller tool for transmission housing (front and rear sections)Transmission: S5D 200G

23 1 141 * Puller link

23 1 142 * Puller fork

23 1 143 * Puller rod with pin

23 1 144 * Spindle

23 1 160 Impact drift for installing inner bearing race and bearing sleeve on outputshaft, for fitting slide piece (5th gear , for fitting output flange, for fittingbearing on countershaft (S5D 310Z)Transmission: 242/4, 245/5, 280/5 Sport, S5D 310Z

23 1 170 Puller tool for front section of transmission housingTransmission: 265/5

23 1 171 * Plate

23 1 172 * Knurled screw (3)

23 1 180 Impact drift for fitting rotary shaft seal in guide tube of clutch release bearingUsed together with: 00 0 500Transmission: 260/5, 265/5, 265/5 Sport, 280/5 Sport

23 1 190 Impact drift for removing and installing input shaft ball bearing in frontsection of transmission housingUsed together with: 00 5 500Transmission: 265/5, 280/5 Sport

23 1 200 Guide bush for centring socket wrench socket when releasing and tighteningtransmission output flange and rear axle differential input flangeUsed together with: 23 1 210Transmission: 265/5, Getrag/ZF

23 1 210 Socket wrench socketUsed together with: 23 1 200 and torque wrenchFor loosening and tightening transmission output flange and rear axledifferential input flangeTransmission: 240/5, 242/4, 245/5, 245/5Sport, 260/5, 262/4, 265/5,265/5Sport, 280/5Sport, 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24,A4S 270R, A4S 310R, A5S 300J, A5S 310Z, A5S 440Z, A5S 560Z, BW 65,Getrag/ZF, S5D 200G, S5D 250G, ZF S5-16

23 1 220 Impact drift for removing and installing roller bearing of countershaft in frontsection of transmission housingUsed together with: 00 5 500Transmission: 260/5, 265/5, A5S 310Z


23 1 230 Spindle (2) for removing inner bearing race from input shaft in front sectionof transmission housingUsed together with: 00 7 500Transmission: 265/5

23 1 240 M Impact drift For fitting rotary shaft seal on selector shaftTransmission: 240/5, 242/4, 245/5, 245/5Sport, 260/5, 262/4, 265/5,265/5Sport, 280/5Sport, 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24,A4S 270R, A4S 310R, A5S 300J, A5S 310Z, A5S 440Z, A5S 560Z, BW 65,S5D 200G, S5D 250G, S6S 420G, ZF S5-16

23 1 250 Clamping pins for removing and installing selector rockerTransmission: 240/5, 260/5, 280/5 Sport, S5D 200G

23 1 260 Impact drift for fitting outer bearing race on front and rear countershaftUsed together with: 00 5 500Transmission: 240/5, 260/5, 280/5 Sport, S5D 200G, S5D 310Z

23 1 270 Impact drift for removing outer bearing race on countershaft in front sectionof transmission housing as well as for removing seal and needle bearingfrom oil pump housing (A5S 560Z)Used together with: 00 5 500Transmission: 240/5, 260/5, A5S 560Z

23 1 280 ExtractorUsed together with: 33 4 020 and 23 1 300For outer bearing race in transmission housing - rear section of countershaftTransmission: 240/5, 265/5, 280/5 Sport, S5D 200G, S5D 310Z

23 1 281 * Replacement claw

23 1 290 Bush for pressing on guide sleeve on to output shaft (1st gear)Transmission: 240/5, 260/5, 280/5 Sport, S5D 200G, S5D 310Z, ZF S5-16

23 1 300 M FixtureUsed together with: 23 2 150For fitting output flange on all manual and automatic transmissions, forinstalling deep groove ball bearing on transmission output shafts and forfitting input flange on all rear axle differentialsTransmission: Getrag/ZF, HAG Type G, HAG Type K, HAG Type M

23 1 301 * Adapter

23 1 302 * Support discUsed together with: 33 1 341For press-fitting input flange on rear axle differential

23 1 303 * Drift

23 1 310 Tool for mounting retainer at deflection leverTransmission: 280/5 Sport


23 1 320 Holder for releasing and tightening nut on output flange with vibrationabsorberModel: 325e, 528eUSTransmission: 240/5

23 1 330 M Spacer plate between cross tube and oil pan for locating engine in positionwhen removing and installing transmissionSeries: E34Model: M5 Transmission: 265/5

23 1 340 Impact drift for fitting rotary shaft seal on transmission input shaftUsed together with: 00 5 500Transmission: 242/4, S5D 200G

23 1 350 Puller tool for rear section of transmission housingUsed together with: 33 1 301Transmission: 265/5

23 1 351 * Plate

23 1 352 * Screw, short (2)

23 1 353 * Screw, long (2)

23 1 360 Impact drift for fitting rotary shaft seal on transmission input shaftUsed together with: 00 5 500Transmission: 240/5, 245/5, 262/4, ZF S5-16

23 1 370 Impact drift for fitting rotary shaft seal of transmission output flangesTransmission: 242/4, 262/4, 265/5, 265/5 Sport

23 1 380 Impact drift for fitting roller bearing of countershaft in rear section oftransmission housingUsed together with: 00 0 500Transmission: 240/5, 245/5, 260/5, 280/5 Sport

23 1 390 Impact drift for fitting roller bearing of countershaft in rear section oftransmission housingUsed together with: 00 5 500Transmission: 265/5, 280/5 Sport

23 1 400 Fixture for fitting rotary shaft seal in bush sleeve of speedometer pinionTransmission: 242/4, 262/4

23 1 401 * Fitting shaft

23 1 402 * Radial plug

23 1 403 * Union sleeve


23 1 410 Impact drift for installing ball bearing on output shaft in rear section oftransmission housing and ball bearing on output shaft in centre section oftransmission housingUsed together with: 00 5 500Transmission: 260/5, 265/5

23 1 420 FixtureUsed together with: 33 1 301For removing slide element (5th gear) Transmission: 265/5

23 1 421 * Clamping screw

23 1 430 Pressure piece for press-fitting 5th gearwheelTransmission: 265/5, 280/5 Sport

23 1 440 Sleeve for press-fitting bearing bush and inner bearing race on output shaftas well as removing output shaft bearing (S5D 310Z)Transmission: 265/5, 265/5 Sport, 280/5 Sport, S5D 310Z

23 1 450 Guide pins (2) for fitting bearing bush in anti-torsion retainer of guide sleeveTransmission: 245/5, 265/5

23 1 460 Puller plate for front section of transmission housingUsed together with: 33 1 301Transmission: 260/5, 280/5 Sport, ZF S5-16

23 1 470 Impact drift for removing and installing deep groove ball bearing in rearsection of transmission housing and for fitting output shaft bearing (S5D200G, S5D 310Z)Used together with: 00 5 500Transmission: 260/5, 280/5 Sport, S5D 200G, S5D 310Z

23 1 480 Impact drift for removing and installing deep-groove ball bearing in frontsection of transmission housingUsed together with: 00 5 500Transmission: 240/5, 242/4, 260/5, 280/5 Sport

23 1 490 Puller tool for gear wheelsTransmission: 240/5, 260/5, 280/5 Sport, S5D 200G, ZF S5-16

23 1 491 * Spacer

23 2 000 Rillex ball bearing extractor 6206 (9 balls with steel cage) for removingdeep groove ball bearing on transmission input shaftTransmission: all Getrag manual transmissions Transmission: Getrag/ZF

23 2 001 * Claw for Rillex 6206 (9)




23 2 010 Rillex ball bearing extractor 6206 E (8 balls with plastic cage) for removingdeep groove ball bearing on transmission input shaftTransmission: 242/4, 245/5 Sport, 265/5

23 2 011 * Claw for Rillex 6206 E (8)



23 2 020 Rillex ball bearing extractor (7 balls) for removing deep groove ball bearingon transmission input shaftTransmission: 245/5 Sport, 265/5 Sport

23 2 021 * Claw for Rillex (7)



23 2 050 Rillex ball bearing extractor 6205 for removing deep groove ball bearing ontransmission countershaft and transmission output shaftTransmission: 245/5 Sport, 262/4, 265/5 Sport

23 2 051 * Claw for Rillex 6305 (8)



23 2 060 Rillex ball bearing extractor 6306 for removing deep groove ball bearing oninput and output shaftTransmission: 242/4, 262/4

23 2 061 * Claw for Rillex 6306 (8)



23 2 080 Adapter for removing guide sleeve (2nd and 3rd gear)Transmission: 260/5

23 2 100 Special pliers for removing and installing circlip on transmission output shaftTransmission: 240/5, 242/4, 245/5, 245/5 Sport, 260/5, 262/4, 265/5, 265/5Sport, 280/5 Sport, 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24, A4S270R, A4S 310R, A5S 300J, A5S 310Z, A5S 440Z, A5S 560Z, BW 65, S5D200G, S5D 250G, S5D 260Z, S5D 310Z, S6S 420G, S6S 560G, ZF S5-16

23 2 150 M Bush for installing deep groove ball bearing on transmission output shaft(260/5, 245/5), fitting front deep groove ball bearing on drive pinion on allrear axle differentials as well as for fitting countershaft cover(S5D 310Z)Used together with: 23 1 300Transmission: 245/5 Sport, 260/5, S5D 310Z


23 2 160 Impact bush for rotary shaft seal in rear section of transmission housing(output shaft)Transmission: 280/5 Sport, ZF S5-16

23 2 170 Fixture for tensioning transmission leaf springTransmission: ZF S5-16

23 2 180 Guide bush for mounting front section of transmission housing on selectorshaftTransmission: ZF S5-16

23 2 190 Fixture for taking up set of gears when removing and installing front sectionof transmission housing and for disassembling set of gearsModel year: as of 11/95Engine: M41Transmission: S5D 200G

23 2 200 Circlip pliers (straight) for removing and installing external circlips ontransmission shaftsTransmission: 240/5, 242/4, 245/5, 245/5 Sport, 260/5, 262/4, 265/5, 265/5Sport, 280/5 Sport, 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24, A4S270R, A4S 310R, A5S 300J, A5S 310Z, A5S 440Z, A5S 560Z, BW 65, S5D200G, S5D 250G, S5D 260Z, S5D 310Z, S6S 420G, S6S 560G, ZF S5-16

23 2 210 Circlip pliers (straight) for removing and installing internal circlips intransmission housings when replacing deep groove ball bearingsTransmission: 240/5, 242/4, 245/5, 245/5 Sport, 260/5, 262/4, 265/5, 265/5Sport, 280/5 Sport, 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24, A4S270R, A4S 310R, A5S 300J, A5S 310Z, A5S 440Z, A5S 560Z, BW 65, S5D200G, S5D 250G, S5D 260Z, S5D 310Z, S6S 420G, S6S 560G, ZF S5-16

23 2 220 Impact drift for bearing in front and rear section of transmission housing(countershaft)Transmission: ZF S5-16

23 2 230 Disc for extracting guide sleeve from gear wheel or output shaft (with preloadon serrated lock washer)Used together with: 00 7 500Transmission: 280/5 Sport

23 2 250 Bracket for clamping main shaft to countershaftTransmission: S5D 310Z

23 2 260 M Drift for fitting rotary shaft seal on selector shaft in rear section oftransmission housingTransmission: S5D 310Z

23 2 270 Fixture for centring selector shaft when fitting front section of transmissionhousingTransmission: S5D 310Z

23 2 280 Puller plate for front section of transmission housingUsed together with: 33 1 301Transmission: S5D 310Z


23 2 290 Fixture for assembling front section of transmission housingTransmission: S5D 310Z

23 2 291 * Base frame

23 2 292 * Support

23 2 293 * Ring

23 2 294 * Set of shells

23 2 300 M Impact drift for fitting radial shaft seal on output shaft in rear section oftransmission housingTransmission: S5D 310Z

23 2 310 Fixture for removing 3rd and 4th gearwheels from countershaftTransmission: S5D 310Z

23 2 320 M Socket wrench socket WAF 36for releasing and tightening flanged nutTransmission: S5D 310Z, S6S 420G, S6S 560G

23 2 330 Fixture for installing complete set of gears in rear section of transmissionhousingTransmission: S5D 310Z

23 2 340 M Impact drift for fitting radial shaft seal in front section of transmission housingTransmission: S5D 310Z

23 2 350 Impact drift for fitting sealing cover for latch pin of selector shaftTransmission: S5D 310Z

23 2 360 Impact drift for installing end cover for latch pin of selector shaftTransmission: S5D 310Z

23 2 370 Fixture for removing gear trainUsed together with: 23 1 050Transmission: S5D 310Z

23 2 380 Sleeve for fitting circlip on input shaftTransmission: S5D 310Z

23 2 390 Sleeve for fitting lock ring on countershaft support discModel year: as of 11/95Engine: M41Transmission: S5D 200G

23 2 400 Fixture for taking up set of gears when installing front section of transmissionhousing and for disassembling set of gearsExcept with engine M41 Transmission: S5D 200G

23 2 410 Sleeve for fitting lock ring on countershaftExcept with engine M41 Transmission: S5D 200G


23 2 420 Spacer sleeve for gauging thickness of shim ring on input shaft bearingTransmission: S5D 200G

23 2 430 M Impact drift for fitting radial shaft seal on input shaft in front section oftransmission housing (S5D 200G) and in output flange (A5S 300J)Transmission: A5S 300J, S5D 200G

23 2 440 Pin for installing bearing tab washer on rear section of transmission housingTransmission: S5D 200G

23 2 450 Impact drift for deep groove ball bearing in rear section of transmissionhousingUsed together with: 00 5 500Transmission: S5D 200G

23 2 460 Sleeve for installing circlip on input shaftTransmission: S5D 200G

23 2 470 M Bush for fitting tab washer for lock nut on output flangeTransmission: S6S 420G, S6S 560G

23 2 480 M Impact bush for fitting rotary shaft seal on output shaftTransmission: S6S 420G, S6S 560G

23 2 490 M Impact bush and slip sleeve for fitting rotary shaft seal on input shaftTransmission: S6S 420G, S6S 560G

23 2 491 * Impact bush

23 2 492 * Slip sleeve (2-part)

23 3 010 M Fixture for press-fitting output flange on output shaftTransmission: S6S 420G, S6S 560G

23 3 011 * Adapter spindle

23 3 012 * Pressure sleeve

23 3 013 * Thrust nut incl. bearing

23 3 020 Bush for installing bellows seal on gear selector rodTransmission: S6S 560G

23 3 030 M Spacer for supporting engine during transmission removalSeries: E38 Engine: M60, M62


Automatic transmission

Explanation:




24 0 010 Device for checking axial play of input shaftUsed together with: 00 2 510Transmission: 4 HP 22, 4 HP 24, A5S 310Z, A5S 560Z

24 0 011 * Dial gauge holder

24 0 012 * Clamping piece

24 0 020 M Oil pressure test accessoriesUsed together with: 13 3 061 and BMW DISFor pressure gauge 13 3 061 or BMW DIS for checking oil pressure Transmission: 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24, A4S 270R,A4S 310R, A5S 300J, A5S 310Z, A5S 440Z, A5S 560Z

24 0 021 * Pressure hose (1.7 m) with connector M12x1.5 - M14x1.5 (external thread) For checking various converter pressuresTransmission: A4S 310R, A4S 270R

24 0 022 * ReducerUsed together with: 24 0 140For checking main pressure (3 HP 22, A5S 310Z) and clutch A (ZFtransmission) /Transmission: 3 HP 22, A5S 310Z, A5S 560Z and all ZF transmissions

24 0 023 * Pipe elbow, extended length 145 mmUsed together with: 13 6 052Transmission: 4 HP 22, 4 HP 24

24 0 024 * Pipe elbow, extended length 90 mmUsed together with: 13 6 052

24 0 025 * Banjo bolt M20x1.5 - M18x1.5 for checking torque converter pressureUsed together with: 24 0 024Transmission: 3 HP 12

24 0 026 * Reducer M24x1.5 - 20x1.5 for checking main pressureUsed together with: 24 0 024Transmission: 3 HP 20


24 0 027 * Reducer M20x1.5 - M18x1.5 for checking main pressure (3 HP 12) andtorque converter pressure (3 HP 20)Togther with: 24 0 024Transmission: 3 HP 12, 3 HP 20

24 0 028 * Screw plug M18x1.5 for closing off oil feed line when checking torqueconverter pressureTransmission: 3 HP 20

24 0 029 * Adapter for closing off supply and return lines when checking main pressureTransmission: 3 HP 22

24 0 030 M Pressure gauge adapter 13 3 061 for checking torque converter pressureUsed together with: 13 3 061, 24 0 021, 24 0 023Transmission: 4 HP 22

24 0 040 Retaining fixture for removing and installing multi-disc assembly Transmission: 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24

24 0 041 * Disc

24 0 042 * Ring

24 0 043 * Half shells

24 0 050 Extractor handle for sealing plugs in lower section of transmission housingTransmission: 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24

24 0 070 M Pressure gauge adapter 13 3 061 for checking pump pressureUsed together with: 13 3 061, 24 0 021, 24 0 023Transmission: 4 HP 22, 4 HP 24

24 0 080 M Funnel for filling transmission with transmission fluidTransmission: 240/5, 242/4, 245/5, 245/5 Sport, 260/5, 262/4, 265/5, 265/5Sport, 280/5 Sport, 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24, A4S270R, A4S 310R, A5S 300J, A5S 310Z, A5S 440Z, A5S 560Z, BW 65, S5D200G, S5D 250G, S5D 260Z, S5D 310Z, S6S 420G, S6S 560G, ZF S5-16

24 0 110 M Impact drift for fitting rotary shaft seal in front section of transmission housingTransmission: as of 90 Transmission: 4 HP 22, 4 HP 24, A5S 310Z

24 0 111 * Ring washer 1 mm Transmission: 4 HP 24 - No. 0 029 160, 4 HP 22 - No. 1 113 936

24 0 130 M Take-up support for removing and installing transmissionUsed together with: 00 2 030 (not included in minimum kit)Transmission: 4 HP 22, 4 HP 24

24 0 140 M Pipe elbow, extended length 135 mm for pressure gauge 13 3 061 andBMW DIS for measuring oil pressure in transmissionUsed together with: 13 3 061, 24 0 021, 24 0 022, 13 6 051, 13 6 052Transmission A4S 270R, A4S 310R, A5S 310Z, A5S 560Z


24 0 150 M Mounting fixture for securing transmission on assembly stand Used together with: 00 1 450Transmission: 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, A4S 270R, A4S 310R,A5S 310Z

24 0 151 * Star clamp for mounting transmissionTransmission: A5S 310 Z


24 0 153 * Spindle with rotary handle

24 0 154 * Mounting stud

24 0 155 * Spacer bush for spindleTransmission: A4S 310 R

24 0 170 M MountUsed together with: 00 2 030 (not included in minimum kit)For removing and installing transmission Transmission: A5S 560 Z

24 0 171 * Adjusting screw

24 0 180 M Mounting fixture for securing transmission on assembly stand Used together with: 00 1 450Transmission: A5S 310Z, A5S 440Z, A5S 560Z


24 0 182 * Thrust spindle with star grip

24 0 183 * Spindlereplaced by 24 0 184

24 0 184 * Spindle, long (2)

24 0 190 M Fixture for mounting output flange of propeller shaft when releasing andtightening slotted nutTransmission: A5S 560 Z

24 0 250 M Take-up support for removing and installing transmissionUsed together with: 24 5 301 and 00 2 030 (not included in minimum kit)Transmission: A5S 440Z

24 1 010 Sleeve for removing multi-disc assembly (4-speed) and for fitting needlebearing in oil pump housing (A5S 560Z)Transmission: 4 HP 22, 4 HP 24, A5S 560Z

24 1 040 Impact bush for fitting rotary shaft seal for torque converter in oil pumphousingTransmission: 3 HP 12


24 1 050 Impact bush for fitting rotary shaft seal for torque converter in oil pumphousingTransmission: 3 HP 20, 3 HP 22

24 1 060 Impact bush for fitting radial shaft seal for torque converter in oil pumphousing and on output flangeTransmission: 3 HP 20, 3 HP 22, A5S 300J, BW 65

24 1 100 Impact bush for fitting rotary shaft seal for output flange in transmissionextensionTransmission: 3 HP 12, 3 HP 20, 3 HP 22

24 1 110 M Socket wrench socket with magnet for releasing and tightening torqueconverter mountTransmission: 4 HP 22, 4 HP 24, A4S 270R, A4S 310R, A5S 300J, A5S310Z, A5S 440Z, A5S 560Z

24 1 120 Gauge for setting position switch in "P" position during assemblyModel year: as from 03/96 Transmission: A4S 270R

24 1 170 M Pin wrench for releasing and tightening slotted nut on output flangeTransmission: A5S 310 Z

24 1 180 M FixtureUsed together with: 24 1 080 (A5S 325Z)For removing and installing oil pumpTransmission: A5S 310Z, A5S 560Z

24 1 190 M Impact drift for fitting rotary shaft seal in front section of transmission housingUsed together with: 00 5 500Transmission: A5S 310 Z

24 1 200 M Assembly sleeve for preventing damage to radial shaft seal when fitting onselector shaftTransmission: A5S 310 Z

24 1 210 Retaining plate for multi-disc assemblyNo longer required as of transmission No. 11 2 300 Transmission: A5S 310 Z

24 1 220 Take-up support for driver flange when loosening slotted nutUsed together with: 24 1 170 (A5S 310Z), 24 4 110 (A5S 440Z)Transmission: A5S 310Z, A5S 440Z

24 1 230 Fixture for removing and installing piston (cover) on brake CTransmission: A5S 310 Z

24 1 240 Gauging fixture for determining shims on brake CTransmission: A5S 310 Z

24 1 250 Fixture for removing and installing brake/clutch unit D/G incl. parkinginterlockTransmission: A5S 310 Z


24 1 260 Fixture For removing and installing cylinder D/E with planetary gear trainTransmission: A5S 560 Z

24 1 261 * Handle

24 1 262 * Spindle with knurled nut


24 1 270 Fixture for removing and installing drive clutch A/B/CTransmission: A5S 560 Z

24 1 271 * Lifting tube with eye bolt

24 1 272 * Lock pin

24 1 280 Fixture for removing and installing brake coupling FTransmission: A5S 560 Z

24 1 281 * Handle with spindle


24 1 283 * Centring handle

24 1 290 Wedges for locating C multi-disc carrier when securing locking tabsTransmission: A5S 560 Z

24 1 300 Tool for securing locking tabs on C multi-disc carrierTransmission: A5S 560 Z

24 1 310 Tool for releasing locking tabs on multi-disc carrier CTransmission: A5S 560 Z

24 2 020 Tool for compressing disc springTransmission: 4 HP 22, 4 HP 24

24 2 030 Tool for compressing disc springTransmission: 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24

24 2 040 Tool for compressing disc springTransmission: 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24

24 2 140 Tensioner for removing and installing snap ring in front of centring plate onZF transmissionsTransmission: 3 HP 12, 3 HP 20, 3 HP 22

24 2 300 M Guide pin for installing automatic transmission with sheet metal flywheelmountedEngine: M30, M50, M52, M60, M62Transmission: 4 HP 22, 4 HP 24, A4S 310R, A5S 310Z, A5S 560Z


24 2 310 Set of toolsFor disassembling and assembling transmission for "Sealing intermediateplate" jobTransmission: A4S 270R, A4S 310R

24 2 311 * Pressure plateFor removing and installing spring retainer

24 2 312 * Spindle M14x1.5 with pressure plate, nut M14 and washerFor removing and installing spring retainer

24 2 313 * Guide pin (2)For fixing gaskets and intermediate plates on intermediate housing

24 2 314 * Slip bushFor removing piston in cylinder of intermediate plate

24 2 320 Socket wrenchFor 3/16" socket head cap screws with 1/4" socket for adjusting brake bandTransmission: A4S 270R, A4S 310R

24 2 330 1/2" open-ended spannerFor adjusting brake bandTransmission: A4S 270R, A4S 310R

24 3 040 Gauge for setting pressure piston when installing selector unitTransmission: 3 HP 12, 3 HP 20, 3 HP 22

24 3 050 Gauge for aligning manual transmissionTransmission: 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24

24 3 140 M Drive bush for checking oil pump operationTransmission: 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24, A5S 560Z

24 3 150 Drive bush for checking oil pump operationTransmission: 3 HP 20, 3 HP 22

24 4 000 M Handle (2) for removing and installing torque converterTransmission: 3 HP 12, 3 HP 20, 3 HP 22, 4 HP 22, 4 HP 24, A4S 270R,A4S 310R, A5S 300J, A5S 310Z, A5S 440Z, A5S 560Z, BW 65

24 4 040 Fixture For checking torque converter for leaksSeries: E31, E32, E34Model: Z3 Transmission: 3 HP 12, 4 HP 24, A4S 270R, A4S 310R

24 4 041 * Valve housing Transmission: 3 HP 12, 4 HP 24

24 4 042 * Retaining screws (2) Transmission: 3 HP 12

24 4 043 * Safety bracket Transmission: 3 HP 12, 4 HP 24, A4S 270R, A4S 310R


24 4 044 * Retaining screws (2)For torque converter /Transmission: 4 HP 24, A4S 270R, A4S 310R

24 4 050 Valve housing Used together with: 24 4 040For checking torque converter for leaksSeries: E12, E28, E34Model: Z3 Transmission: 3 HP 20, 3 HP 22, A4S 270R, A4S 310R

24 4 070 Fixture For checking torque converter for leaksTransmission: 3 HP 20, 3 HP 22, 4 HP 22

24 4 080 Fixture For holding torque converter in position when removing and installingtransmissionTransmission: 4 HP 22, 4 HP 24

24 4 090 M Impact driftUsed together with: 00 5 500For installing radial seal on output endTransmission: A5S 440Z, A5S 560Z

24 4 100 M Impact drift for fitting rotary shaft seal on input end (behind torque converter)Transmission: A5S 440Z, A5S 560Z

24 4 110 M Wrench for releasing and tightening slotted nut on output flangeTransmission: A5S 440Z, A5S 560Z

24 4 130 Locating toolFor holding torque converter in position when removing and installingtransmissionTransmission: A4S 310R, A5S 300J, A5S 310Z, A5S 440Z, A5S 560Z

24 4 131 * Basic unit

24 4 132 * Blade for transmission A5S 440Z

24 4 133 * Blade for transmission A4S 310R

24 4 134 * Blade for transmissions A5S 310Z, A5S 560Z and A5S 300J

24 4 135 * Blade for transmission A5S 560Z

24 4 136 * Counterplate

24 5 120 M Tool For centring torque converter bell housing with respect to oil pump duringassemblyTransmission: A4S 270R, A4S 310R



24 5 122 * Centring pin (3)

24 5 150 M Centring pin with thread (2) for centring selector unit in transmission duringassemblyTransmission: A4S 270R, A4S 310R

24 5 160 Centring pins for centring main housing with respect to intermediate housingand torque converter housing (2)Transmission: A4S 270R, A4S 310R

24 5 180 Socket wrench socket 1/2 " for releasing and tightening selector unitTransmission: A4S 310 R

24 5 190 M Pressure gauge adapter 13 3 061 for checking transmission oil pressureUsed together with: 13 3 061, 13 3 067, 24 0 021, 24 0 023, 24 0 140Transmission: A4S 270R, A4S 310R

24 5 210 Holder for releasing and tightening gearshift cableTransmission: 4 HP 22, 4 HP 24, A4S 270R, A4S 310R, A5S 310Z

24 5 220 Holder for releasing and tightening gearshift cableTransmission: A5S 300J, A5S 310Z

24 5 230 M Ring for fitting rotary shaft seal on selector shaftTransmission: 4 HP 22, 4 HP 24, A5S 310Z

24 5 240 Holder for releasing and tightening gearshift cableTransmission with position switchTransmission: A5S 310Z, A5S 560Z

24 5 250 M Bush for installing rotary shaft seal in selector shaftUsed together with: 24 5 490Transmission: A5S 310Z, A5S 560Z

24 5 260 M Tool for removing rotary shaft seal in selector shaftTransmission with position switchTransmission: A5S 310Z, A5S 440Z, A5S 560Z

24 5 270 M Bush for installing rotary shaft seal in selector shaftUsed together with: 24 5 490Transmission: A5S 440Z

24 5 300 M Take-up support for removing and installing transmissionUsed together with: 00 2 030 (not included in minimum kit)Transmission: A4S 270R, A4S 310R, A5S 310Z, A5S 440Z

24 5 301 * Base plate Transmission: A4S 310R, A4S 310R

24 5 302 * Support mount (2) Transmission: A4S 310 R

24 5 303 * Support pin (4)Transmission: A4S 310Z


24 5 350 Support plate for automatic transmissionTransmission: A5S 300J Others: Japan only, South Africa only

24 5 360 Tool for removing and installing rotary shaft seal of selector shaftTransmission: A4S 310 R

24 5 361 * Threaded bush

24 5 362 * Union nut

24 5 363 * Bush for transmission without position switch

24 5 364 * Nut

24 5 365 * Slip sleeve (5)

24 5 370 Bush for fitting rotary shaft seal on selector shaftUsed together with: 24 5 364 and 24 5 365Only with position switchSeries: E39Transmission: A4S 310R Others: USA only

24 5 490 M Slip sleeve (5) for preventing damage to rotary shaft seal when fitting onselector shaftTransmission: A5S 310Z, A5S 440Z, A5S 560Z

24 6 000 M 8-pin test lead for automatic transmission (EH transmission)Transmission: 4 HP 22, 4 HP 24

24 6 010 M 9-pin test lead for automatic transmission (EH transmission)Transmission: A4S 270R, A4S 310R

24 6 020 M 14-pin test lead for automatic transmission (EH transmission)Transmission: A5S 310 Z

24 6 029 * Handbook

24 6 060 M 16-pin test lead for automatic transmission (EH transmission)Transmission: A5S 310Z, A5S 560Z


Propeller shaft

Explanation:




26 1 000 Gauge for aligning centre bearing of propeller shaftSeries: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

26 1 001 * Rail

26 1 002 * Bearing bracket

26 1 003 * Chocks for propeller shaft (dia. of 50 mm front, 70 mm rear)

26 1 004 * Chocks for propeller shaft (dia. of 50 mm front, 60 mm rear)

26 1 005 * Knurled screws

26 1 010 Clips for Giubo rubber couplingSeries: E12, E21, E23, E24

26 1 011 * Clamp, dia. 130 mm - 6 hole/6 cylinder Series: E12, E23, E24

26 1 012 * Clamp, dia. 107 mm - 8 hole/4 cylinder Series: E12, E21

26 1 020 Gauge For aligning propeller shaftSeries: E12, E21, E23, E24, E28, E30

26 1 030 Fixture For checking and adjusting deflection angle of propeller shaftSeries: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

26 1 031 * Spirit level

26 1 040 Wrench for screw bush on slide element of propeller shaftSeries: all, except 4-wheel driveSeries: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

26 1 060 Wrench for screw bush on slide element of propeller shaftSeries: E30Model: 325ix

26 1 080 Drift for removing guide bearing from propeller shaftSeries: E31


26 1 100 Support plate on rear axle differential for determining angle of defractionUsed together with: 26 1 090 or 26 1 030Series: E31, E32

26 1 110 M Plate For removing constant velocity joint from propeller shaftSeries: E31, E32, E34, E36, E38, E39Model: Z3


General electrical system

Explanation:




61 0 000 Analog/digital multimeter Metrahit 14SReplaces analog/digital multimeter M 2005Series: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

61 0 001 * Fuse link 16 A / 600 VFor Metrahit 14S (10 mm x 38 mm)

61 0 002 * Fuse link FF 1.6 A / 500 VFor Metrahit 14S (6.3 mm x 32 mm)

61 0 030 Analog/digital multimeter Metrahit 18SReplaces analog/digital multimeter M 2008Series: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

61 0 031 * Fuse link 16 A / 600 V For Metrahit 18S (10 mm x 38 mm)

61 0 032 * Fuse link FF 1.6 A / 500 V For Metrahit 18S (6.3 mm x 32 mm)

61 1 130 Set of extractors for contactsBelongs to 61 1 150Series: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

61 1 131 * Extractor for 1.5 mm round contacts



61 1 134 * Extractor for miniature flat spring contacts

61 1 135 * Extractor for standard flat spring contacts

61 1 136 * Extractor For Power Timer contacts (G & H)

61 1 137 * Extractor for timer contacts

61 1 138 * Box spanner For indicator lamps (instrument cluster)


61 1 140 Set of unlocking tools for round plugs (ELA)Belongs to 61 1 150Series: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

61 1 141 * Unlocking tool for D 2.5 / ELA, 4-pin, round


61 1 143 * Unlocking tool for D 2.5 / ELA, 12-pine, round



61 1 150 M Unlocking tool for round plug / extractor toolContains 61 1 130 and 61 1 140Series: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

61 1 151 * Extractor for power timer contacts (AMP / Bosch)

61 1 152 * Extractor for micro-timer contacts

61 1 153 * Unlocking tool for retaining clips of relay holder

61 1 154 * Inlay for caseOnly for delivery 8/95

61 1 155 * Spare sleeve ø 3.5 mm for 61 1 133



61 1 158 * Case with inlay

61 1 159 * Handbook

61 1 160 M Extractor For 6-pin connector housing, seat/mirror memorySeries: E31, E32

61 1 230 M Setting cotter For maintaining extension height when adjusting nozzle (washer nozzle) onboot lidSeries: E34tou

61 1 240 M Wrench For removing and installing securing ring of washer nozzle on boot lidSeries: E34tou

61 1 250 M Pliers For removing relays from fuse boxSeries: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39


61 1 300 M Pliers For disassembling outside mirror switch /Model year: as of 83Series: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

61 1 310 M Pin wrench For removing and installing headlight washer system (nozzles)Series: E31

61 1 320 M Assembly gauge For aligning windscreen wiper drive with respect to windscreen wiper spindleon rear windowSeries: E39tou

61 1 350 Set of tools For removing and installing plug-in socket in transmission connector onautomatic transmissionTransmission: 4 HP 22, 4 HP 24

61 1 351 * Extractor

61 1 352 * Fitting drift

61 1 360 Releasing toolFor releasing connector housing from holder / multiple locked holderSeries: E30, E31, E32, E34, E36, E38, E39

61 1 410 Set of DIS test prodsSeries: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

61 1 411 * Pick-off terminal SAGK4-K, red

61 1 412 * Pick-off terminal SAGK4-K, black

61 1 413 * Pick-off terminal SAGK4, red

61 1 414 * Pick-off terminal SAGK4, black

61 1 415 * Pick-off terminal SAGK4-30, red

61 1 416 * Pick-off terminal SAGK4-30, black

61 1 417 * test prod SPP4-S, red

61 1 418 * Test prod SPP4-S, black

61 1 419 * Clamp-type test prod KPS6/4-S, red

61 1 420 * Decade number must not be assigned

61 1 421 * Clamp-type test prod KPS6/4-S, black

61 1 422 * 6-fold potential distributor, black


61 1 440 M Test lead for K-JetronicSeries: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

61 1 450 M 26-pin peripheral box and cables (8)For checking control unitsSeries: E23, E24, E28, E30, E32, E34

61 1 451 * 26-pin V-adapter lead (Modu), yellow

61 1 452 * 26-pin V-adapter lead (Modu), white

61 1 453 * 26-pin V-adapter lead (Modu), blue

61 1 454 * 26-pin V-adapter lead (Modu), green

61 1 455 * 26-pin V-adapter lead (Modu), brown

61 1 456 * 26-pin V-adapter lead (Modu), black

61 1 457 * V-adaper lead (D 2.5) 5-pin

61 1 458 * Test lead with 15 Amp fuse (D 4.0)

61 1 459 * 26-pin peripheral box (D 4.0 sockets)

61 1 460 M Set of V-adapter leads (8) For troubleshooting on wiring harness interfaces (e.g. door wiring harness)Series: E32, E36, E38

61 1 461 * 2-pin V-adapter lead (D 2.5), waterproof, yellow

61 1 462 * 2-pin V-adapter lead (D 2.5), waterproof, blue

61 1 463 * 2-pin V-adapter lead (D 2.5), waterproof, black

61 1 464 * 2-pin V-adapter lead (D 2.5), waterproof, white

61 1 465 * 2-pin V-adapter lead (D 2.5), waterproof, white, angled

61 1 466 * 2-pin V-adapter lead (D 2.5), waterproof, black, angled

61 1 467 * 3-pin V-adapter lead (D 2.5), waterproof, black

61 1 468 * 10-pin V-adapter lead (VEK), grey

61 1 470 M Set of cables (6 ) for measuring and test purposesSeries: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

61 1 471 * 6-pin V-adapter lead (Modu), black for IHR/IHKA stepper motorsSeries: E31, E32, E34

61 1 472 * 1-pin test lead (D 4.0), red


61 1 473 * 1-pin test lead (D 2.5), red

61 1 474 * 1-pin test lead (D 4.0), black

61 1 475 * 1-pin test lead (D 2.5), black

61 1 476 * Test lead with 12 A fuse (D 2.5)

61 1 477 * 18-pin V-adapter lead (Modu) for heating controlReplaced by 61 4 470 Series: E34

61 1 480 M Set of V-adapter leads (7 ) for vehicle electrical systemSeries: E30, E32, E34

61 1 481 * 26-pin V-adapter lead (VEK), green

61 1 482 * 26-pin V-adapter lead (VEK), white

61 1 483 * 26-pin V-adapter lead (VEK), beige

61 1 484 * 24-pin V-adapter lead (VEK) brown, 12-pin V-adapter lead (VEK), grey

61 1 485 * 26-pin V-adapter lead (VEK), yellow

61 1 486 * 26-pin V-adapter lead (VEK), blue

61 1 487 * 14-pin V-adapter lead (VEK / gear indicator), green

61 1 490 M Set of V-adapter leads (2 ) for engine wiring harnessSeries: E34

61 1 491 * 3-pin V-adapter lead (JPT / engine wiring harness), zero-coded

61 1 492 * Adapter cable for relays

61 1 493 * 12-pin V-adapter lead (VEK), green for IHR control unit

61 2 010 M Ignition lead adapterSeries: E31, E32 Engine: M70

61 2 020 M Bypass connector for frequency simulator (speedometer signal)Series: E32

61 2 030 M Adapter for checking push buttonsSeries: E32

61 2 040 M V-adapter lead for infrared locking systemSeries: E31, E32, E34, E36

61 2 050 M 2-pin V-adapter lead (JPT), black for ServotronicSeries: E31, E32, E34

61 2 060 M 15-pin/20-pin adapter for diagnostic socket Series: E21, E23, E24, E28, E30


61 2 070 M Set of cables for electric seat adjustmentSeries: E31, E36, E38

61 2 071 * Power supply cable

61 2 072 * Adapter leadSeries: E36

61 2 073 * Adapter leadSeries: E38

61 2 300 Adapter for measuring closed-circuit currentSeries: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

61 2 400 LadematicSeries: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

61 2 401 * Floating current charger

61 2 402 * Auxiliary lead with battery terminals

61 2 409 * Handbook

61 3 010 M Tester and set of relay plug adapters (8 ) for checking relay functionsSeries: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39

61 3 011 * Tester for checking relay functions

61 3 013 * Connector insert (crash sensor)

61 3 014 * Connector insert (hazard warning system)

61 3 015 * Connector insert (hazard warning system C2)

61 3 016 * Connector insert (ABS)

61 3 017 * Connector insert (changeover relay)

61 3 018 * Connector insert (n/o relay)

61 3 019 * Connector insert (rear window heater)

61 3 021 * Connector insert (windscreen heater)

61 3 029 * Handbook

61 3 030 M V-adapter lead for checking lines between DSC3 control unit (DynamicStability Control 3) and rotation rate sensorSeries: E38Engine: M73 Others: ECE only

61 3 050 M Relay bypass switch for checking fuel pumpSeries: E12, E21, E23, E24, E28, E30, E31, E32, E34, E36, E38, E39


61 3 100 Unlocking tool for light switchModel: Z3

61 3 190 M Test lead for EWS 3 (Electronic Vehicle Immobilization)Model year: as of 96Series: E38, E39

61 3 300 M Removal toolFor removing ring antenna at ignition lockSeries: E30/C, E30tou, E31, E32, E32/3, E34, E34tou, E36, E36/2, E36/5,E36/C, E36tou, E38, E38/3, E39, E39tou, E46

61 4 410 M Set of 88-pin test adaptersSeries: E31, E32, E34

61 4 411 * 88-pin test adapter

61 4 412 * Multimeter test lead (2 mm), 1-pin, black

61 4 413 * Multimeter test lead (2 mm), 1-pin, red

61 4 414 * Test lead for BMW SERVICE TESTER, 2 mm, black

61 4 415 * Test lead for BMW SERVICE TESTER, 2 mm, red

61 4 418 * Operating instructionsReplaced by 61 4 429

61 4 419 * Locking lever for 88-pin and 83-pin test adapters

61 4 420 M Set of 83-pin test adapters for checking and troubleshooting ABS-5 peripheryIncluded in set: 61 4 412 and 61 4 413Series: E31, E34, E38

61 4 421 * 83-pin test adapter

61 4 429 * Handbook

61 4 430 M Set of test lead extensionsSeries: E31, E32, E34

61 4 431 * Test lead extension, 1-pin, red (cable length 4.5 m)

61 4 432 * Test lead extension, 1-pin, black (cable length 4.5 m)

61 4 440 Test box for microswitch (door control as well as EH and EM convertible top)Series: E30Model: Z1

61 4 450 M 20-pin V-adapter lead (D 2.5), black for light control module (LKM) and EMconvertible topUsed together with: 61 1 459Series: E30, E31, E36


61 4 460 M Set of 26-pin V-adapter leads (Elo), zero-coded for IHR 2 KEEKUsed together with: 61 1 459Series: E30, E31, E34, E36

61 4 461 * 26-pin V-adapter lead (Elo), zero-coded, cable 1




61 4 470 M 18-pin V-adapter lead (Elo), zero codedUsed together with: 61 1 459Series: E31, E34, E36

61 4 480 M 12-pin V-adapter lead (Elo), zero coded for EDCUsed together with: 61 1 459Series: E31, E36

61 4 489 * Handbook

61 4 490 M 20-pin V-adapter lead (D 2.5), white for lamp control module and wiringharnessUsed together with: 61 1 459Series: E31, E36

61 5 410 M 5-pin V-adapter lead (D 2.5), black for multimeter measurements atelectronic body module and its peripherySeries: E31

61 6 000 M PullerFor removing windscreen wiper arm (E38, E39 passenger side only) fromdrive shaftSeries: E32, E34, E36, E38, E39tou

61 6 001 * Basic body

61 6 002 * Screw

61 6 003 * Thrust piece

61 6 010 M Torx socket T80 with holder for releasing and tightening windscreen wiper(driver's side)Series: E31, E38, E39

61 6 011 * 3/8" holder

61 6 012 * Torx socket T80


61 6 020 M Set of V-adapter leads (6 V-adapter leads) D2.5/ELA plug-in system forelectrical testing at disconnected plug connections (auxiliary fan of airconditioning system etc.)Used together with: 61 1 459 and 61 0 000 or BMW DIS; D 2.5 = Contactdiameter 2.5 mm ELA = Single conductor sealSeries: E38

61 6 021 * 2-pin V-adapter lead (D 2.5/ELA), oval, zero-coded Used together with: 61 0 000 or BMW DIS

61 6 022 * 4-pin V-adapter lead (D 2.5/ELA), oval, zero-coded Used together with: 61 0 000 or BMW DIS

61 6 023 * 4-pin V-adapter lead (D 2.5/ELA), single-row, zero-coded Used together with: 61 0 000 or BMW DIS

61 6 024 * 7-pin V-adapter lead (D 2.5/ELA), round, blackUsed together with: 61 0 000 or BMW DIS

61 6 025 * 24-pin V-adapter lead (D 2.5/ELA), hybrid (Elo), blackUsed together with: 61 1 459 and 61 0 000 or BMW DIS

61 6 026 * 21-pin V-adapter lead (D 2.5/ELA), hybrid (Elo), blackUsed together with: 61 1 459 and 61 0 000 or BMW DIS

61 6 029 * Handbook

61 6 030 M Set of V-adapter leads (5 V-adapter leads) Elo plug-in system for electricaltesting at disconnected plug connections (program selector switch onautomatic transmission etc.)Used together with: 61 0 000 or BMW DIS; Elo = Electronic contactSeries: E38

61 6 031 * 3-pin V-adapter lead (Elo), zero codedUsed together with: 61 0 000 or BMW DIS


61 6 033 * 6-pin V-adapter lead (Elo), single-row, zero-coded Used together with: 61 0 000 or BMW DIS

61 6 034 * 6-pin V-adapter lead (Elo), double-row, zero-coded Used together with: 61 0 000 or BMW DIS


61 6 039 * Handbook

61 6 040 M Set of V-adapter leads (5 V-adapter leads) Elo/ELA plug-in system forelectrical testing at disconnected plug connections (e.g. on EDC)Used together with: 61 0 000 or BMW DIS; Elo = Electronic contact ELA =Single conductor sealSeries: E38


61 6 041 * 3-pin V-adapter lead (Elo/EAL), round (EDC)

61 6 042 * 3-pin V-adapter lead (Elo/ELA), round, zero-coded Used together with: 61 0 000 or BMW DIS

61 6 043 * 2-pin V-adapter lead (Elo/ELA), oval, zero-coded Used together with: 61 0 000 or BMW DIS



61 6 049 * Handbook

61 6 070 Set of accessories for repair kit IV for vehicle electrical system61 9 020 Comb connector system D 2.5/ELA, D 1.5/ELA plug-in systemsSeries: E38

61 6 071 * Flat plug-in sleeve for 4 mm² (comb connector)

61 6 072 * Pin housing (D 2.5/ELA), 2-pin, oval (line cross section 0.35...2.5 mm²)

61 6 073 * Socket housing (D 2.5/ELA), 2-pin, oval (line cross section 0.35...2.5 mm²)

61 6 074 * Socket housing (D 2.5/ELA), 4-pin, oval

61 6 075 * Socket housing (D 2.5/ELA), 4-pin, single-row

61 6 076 * Socket housing (D 2.5/ELA), 6-pin/8-pin, oval

61 6 077 * Socket and pin housing (D 1.5/ELA), 4-pin, round

61 6 080 Set of accessories for repair kit IV for vehicle electrical system61 9 020 Elo plug-in systemElo = Electronic contactSeries: E38

61 6 081 * Pin housing (Elo), 3-pin/6-pin, single-row

61 6 082 * Socket housing (Elo), 2-pin/3-pin/6-pin, single-row

61 6 090 Set of accessories for repair kit IV for vehicle electrical system61 9 020 Elo/ELA plug-in systemElo = Electronic contact ELA = Single conductor sealSeries: E38

61 6 091 * Socket housing (Elo ELA), 2-pin/3-pin/4-pin, oval

61 6 092 * Pin housing (Elo/ELA), 3-pin, round

61 8 080 Additions to repair kits I, II and III with operating instructions "Tools for wiringharness repairs"Series: E12, E21, E23, E24, E28, E30


61 8 081 * Additions to repair kit I

61 8 082 * Additions to repair kit II

61 8 083 * Additions to repair kit III

61 8 084 * Operating instructions "Tools for wiring harness repairs", repair kits I, II, III

61 9 020 M Repair kit IV for vehicle electrical systemIncluded in scope of delivery: 61 9 030, 61 9 040, 61 9 050 and61 9 070 Series: E30, E31, E32, E34, E36, E38

61 9 029 * Operating instructionsVolume 1 to 4

61 9 030 M Drawer case without contents for repair kit IVSeries: E30, E31, E32, E34, E36, E38

61 9 031 * Tray inlays (20 ) with compartment partitions

61 9 032 * Tool tray

61 9 033 * Cover insert Kit IV

61 9 040 M Set of tools for repair kit IVSeries: E12, E21, E23, E24, E28, E30, E30/C, E30tou, E31, E32, E32/3, E34,E34tou, E36, E36/2, E36/5, E36/C, E36tou, E38, E38/3, E39, E39PL, E39tou,E46

61 9 041 * Hand-held stock without die

61 9 042 * Female dieFor crimping connectors and contact sleeves for comb connectors

61 9 043 * Insulation stripper pliers with wire cutter

61 9 044 * Female dieFor crimping antenna plug connector (antenna cable/radio plug connection)

61 9 050 M Repair kits A...N for Kit IVPreassembled cable ends with connector housings as well as contacts,connectors, shrink sleeves and dummy grommets connected on both endsSeries: E30, E31, E32, E34, E36, E38

61 9 051 * Repair kit A (comb connector)

61 9 052 * Repair kit B (plug-in system D 2.5 ELA)

61 9 053 |FMT - Text# * Repair kit C (plug-in system D 2.5)

61 9 054 * Repair kit D (plug-in system D 2.5 WD)For orders of individual parts of repair kit D refer to 61 9 080

61 9 055 * Repair kit E (plug-in system Timer)


61 9 056 * Repair kit F (plug-in system MDK/DFK)

61 9 057 * Repair kit G (plug-in system Modu)

61 9 058 * Repair kit H (plug-in system Elo)

61 9 059 * Repair kit I (plug-in system Elo ELA)

61 9 061 * Repair kit K (plug-in system Timer, gold)

61 9 062 * Repair kit L (pin housing for plug-in system Elo ELA)

61 9 063 * Repair kit M (pin and socket housing for plug-in system Elo ELA)

61 9 064 * Repair kit N (plug-in system D 1.5 ELA)

61 9 070 M Individual parts for repair kit IV for vehicle electrical system 61 9 020Consisting of:- Supplementary kits 61 6 070, 61 6 080 and 61 6 090- Individual parts 61 9 400Series: E38

61 9 080 Repair kit for plug-in system D 2.5, waterproofConsisting of:- Cable ends (6)- Joint connector 61 9 475- Joint connector 61 9 476- Shrink-fit sleeve with fuse link 61 9 425Does not belong to repair kit IV for vehicle electrical system 61 9 020 Onlyon individual orders Series: E36, E38

61 9 081 * Cable end with socket contact 1.0 mm² 4-pack

61 9 082 * Cable end with socket contact 2.5 mm² 4-pack

61 9 083 * Cable end with pin contact 1.0 mm² 2-pack

61 9 084 * Cable end with pin contact 2.5 mm² 2-pack

61 9 085 * Cable end with angle sockets 1.0 mm² 10-pack

61 9 086 * Cable end with angle sockets 2.5 mm² 4-pack

61 9 400 Individual parts belonging to repair kit IV for vehicle electrical system 61 9 020The complete scope of individual parts 61 9 401 to 61 9 476 is onlysupplied together with the repair kit IV for vehicle electrical system61 9 020 Series: E38


61 9 401 * Order No., old: 1 270 973Grommet for connector housing, 5-pin, black, with release (JT)Number per pack: 2




61 9 405 * Order No., old: 1 378 147Grommet for socket housing, 6-pin, black, with slideNumber per pack: 1

61 9 406 * Order No., old: 1 378 149Socket housing, 2-pin, black, repair kit CNumber per pack: 4

61 9 407 * Order No., old: 1 378 400Socket housing, 2-pin, black, repair kit DNumber per pack: 3

61 9 408 * Order No., old: 1 378 402Socket housing, 2-pin, grey, repair kit DNumber per pack: 3

61 9 409 * Order No., old: 1 378 404Pin housing, 2-pin, black, repair kit DNumber per pack: 3


61 9 411 * Order No., old: 1 378 406Pin housing, 2-pin, grey, repair kit DNumber per pack: 3

61 9 412 * Order No., old: 1 378 408Socket housing, 2-pin, black, oval, Repair kit DNumber per pack: 2


61 9 414 * Order No., old: 1 378 412Socket housing, 3-pin, black, angled, repair kit DNumber per pack: 2


61 9 415 * Order No., old: 1 378 416Socket housing, 2-pin, black, angled, repair kit DNumber per pack: 2

61 9 416 * Order No., old: 1 378 418Socket housing, 2-pin, grey, angled, repair kit DNumber per pack: 2



61 9 419 * Order No., old: 1 378 426Socket housing, 6-pin, black, with slide, repair kit CNumber per pack: 1






61 9 425 * Order No., old: 1 379 833Shrink-on sleeve with fuse link Number per pack: 30

61 9 426 * Order No., old: 1 382 530Grommet for socket housing, 4-pin, black, with slideNumber per pack: 1

61 9 427 * Order No., old: 1 383 764Socket housing, 26-pin, brown, Siemens, aquamarine cap 45ø, repair kit HNumber per pack: 2

61 9 428 * Order No., old: 1 383 777Pin housing, 4-pin, black, ELA round, Repair kit BNumber per pack: 2


61 9 429 * Order No., old: 1 383 783Pin housing, 7-pin, black, round, repair kit BNumber per pack: 1


61 9 431 * Order No., old: 1 383 869Pin housing, 10-pin, black, AMP, black cap, repair kit HNumber per pack: 2

61 9 432 * Order No., old: 1 383 886Socket housing, 10-pin, black AMP, black cap, repair kit HNumber per pack: 2

61 9 433 * Order No., old: 1 383 901Caps for housings, 4-pin, black, ELA roundNumber per pack: 1

61 9 434 * Order No., old: 1 383 903Caps for housings, 7-pin, black, ELA roundNumber per pack: 1

61 9 435 * Order No., old: 1 387 140Contact sleeve 0.35-0.5 mm², for comb connector 61 9 438Number per pack: 15



61 9 438 * Order No., old: 1 387 150Comb connector with 17 plug-in tinesNumber per pack: 5

61 9 439 * Order No., old: 1 387 160Socket housing, 4-pin, black, AMP, black cap, repair kit HNumber per pack: 2


61 9 441 * Order No., old: 1 387 177Pin housing, 4-pin, black, AMP, black cap, repair kit HNumber per pack: 2

61 9 442 * Order No., old: 1 392 222Socket housing, 4-pin, black, ELA round, repair kit BNumber per pack: 2

61 9 443 * Order No., old: 1 392 226Socket housing, 7-pin, black, round, Repair kit BNumber per pack: 1


61 9 444 * Order No., old: 1 392 232Double flat spring, gold 0.75-1.0 mm², for 3-pin connector housingNumber per pack: 15

61 9 445 * Order No., old: 1 392 242Socket housing, 18-pin, black, AMP, aquamarine cap 45ø, repair kit HNumber per pack: 2

61 9 446 * Order No., old: 1 393 7183-pin comb connector housing, with retainer hooksNumber per pack: 2



61 9 449 * Order No., old: 1 392 7373-pin comb connector housing with retainer lugNumber per pack: 2


61 9 451 * Order No., old: 1 392 7395-pin comb connector housing, with retainer lugNumber per pack: 2

61 9 452 * Order No., old: 1 392 742Socket housing, 2-pin, black, repair kit INumber per pack: 2

61 9 453 * Order No., old: 1 392 743Pin housing, 2-pin, black, repair kit INumber per pack: 2

61 9 454 * Order No., old: 1 392 7669-pin comb connector housing with retainer lugNumber per pack: 2

61 9 455 * Order No., old: 1 392 771Pin housing, 4-pin, black, ELA round, Repair kit BNumber per pack: 1

61 9 456 * Order No., old: 1 706 0912-pin connector housing, black, with release (JT), repair kit ENumber per pack: 3






61 9 461 * Order No., old: 1 711 262Grommet for socket housing, 7-pin, black, roundNumber per pack: 1

61 9 462 * Order No., old: 1 714 053Socket housing, 8-pin, black, round, Repair kit CNumber per pack: 1

61 9 463 * Order No., old: 1 718 126Socket housing, 7-pin, black, round, Repair kit CNumber per pack: 1

61 9 464 * Order No., old: 1 724 452Grommet for connector housing, 3-pin, blackNumber per pack: 2

61 9 465 * Order No., old: 1 724 4783-pin connector housing, black, contacts 61 9 444Number per pack: 2

61 9 466 * Order No., old: 1 732 4602-pin connector housing, black, I-coded, with release (JPT), repair kit KNumber per pack: 1

61 9 467 * Order No., old: 1 732 4612-pin connector housing, black, II-coded, with release (JPT), repair kit KNumber per pack: 1

61 9 468 * Order No., old: 1 732 4622-pin connector housing, black, III-coded, with release (JPT), repair kit KNumber per pack: 1

61 9 469 * Order No., old: 1 732 5963-pin connector housing, black, with release (JPT), repair kit KNumber per pack: 2


61 9 471 * Order No., old: 1 732 634Grommet for connector housing, 3-pin, black, with release (JPT)Number per pack: 2

61 9 472 * Order No., old: 1 732 694Grommet for connector housing, 2-pin, black, with release (JPT)Number per pack: 2


61 9 473 * Order No., old: 8 353 712Socket housing, 6-pin, black, AMP, aquamarine cap 90ø, repair kit HNumber per pack: 2

61 9 474 * Order No., old: 8 353 746Joint connector 0.35-0.50 mm²Number per pack: 20

61 9 475 * Order No., old: 8 353 747Joint connector 0.75-1.00 mm²Number per pack: 20

61 9 476 *


bmw e46 tool

Documents

securing engine

engine hoistfor

engine m52tuexplanation

engine mounting plates

engine mounting fixture

support chain

valve springsused

diesel engineused