beaded pearl ring beading & jewelry making tutorial … · these materials can be purchased...
TRANSCRIPT
BEADED PEARL RING BEADING & JEWELRY MAKING TUTORIAL SERIES T143
COPYRIGHT
XQ Designs
Copyrights XQ Designs 2012
Published By DIY Beading Club
INTRODUCTION
Here's a fun and easy way to create a beaded ring.
This tutorial will teach you how to use right angle weaving technique and create a ring using
pearls, bicones and seed beads. You'll learn how to do right angle weave in circular direction
which created the flower shape center of the ring. This tutorial will also teach you the basic
right angle weaving technique which created the ring band.
Level: Beginner
MATERIALS AND TOOLS NEEDED:
Materials Needed
4 x 4mm white Pearls Several colored blue 11/0 Seed beads 4 x 4mm blue Bicone crystals 4 dark blue 11/0 Seed beads Nylon thread
Tools Needed
Scissors
Where to buy materials:
These materials can be purchased from most bead shops around your area. In case you have
difficulty getting it, you can purchase DIY Kit from. http://www.diylessons.org/Beaded-
Pearl-Ring-Jewelry-Making-Tutorial-KIT-T147,name,326534,item_id,0,ad_type,ad_details or
contact [email protected]
STEP BY STEP INSTRUCTIONS
STEP 1:
Cut an arm span of nylon thread and slide in 4 dark blue seed beads. Position the seed beads
at the center of the thread.
Cross both threads into a seed bead.
Pull the thread.
STEP 2:
On your right thread slide in a bicone and a pearl. On your left thread slide in a bicone.
Cross both threads into the bicone on your left thread shown in arrow.
STEP 3:
Insert your left thread into the nearest seed bead shown in arrow.
Continue by sliding in a bicone on your left thread and a pearl on your right thread.
Cross both threads into the bicone on your left thread.
STEP 4:
Repeat Step3. Insert the left thread into the nearest seed bead.
On your left thread slide in a bicone and on your right thread slide in a pearl.
Then cross both threads into the bicone on your left thread.
STEP 5:
Insert your left thread into the seed bead and out into the bicone shown in arrows.
Finally, cross both threads into a pearl.
STEP 6:
Pull the thread tight. You would notice that the center part - bicones and seed beads are popping out and is creating a dome shape.
STEP 7: CREATING THE RING BAND
Slide in 2 seed beads on your left and right thread.
Then cross both threads into 2 seed beads and pull.
STEP 8:
Repeat Step 7 of creating the ring band until you reach your desired length.
STEP 9:
After reaching your desired length, to end the ring band slide in 2 seed beads on your left and right thread.
Then cross both thread into the opposite pearl.
Pull the thread and fit into your finger. To secure the thread, going in crisscross direction
insert the threads halfway back thru the ring band then tie a knot. Insert again back thru the
seed beads until you get to the other side. Cut off excess thread.
You're done! Create as many as you like in different colors.
SPECIAL OFFER FOR READERS
We are giving special discount to our existing readers who purchase any jewelry making
membership package at DIY Beading Club. Just use this coupon code C8E005B8
to claim for 10% discount on any of our membership package at DIY Beading Club
CONTACT US
If you have any query or feedback for the tutorial, please contact us at
ABOUT THE AUTHOR
Started as a hobby, I have then addicted into sharing my knowledge through tutorial
writing. I publish my knowledge and research through my websites. I also work with
other jewelry artists to develop tutorials and publish their works. I hope you will
browse through all our creations and hope you will like them.
Do join me at
Browse my ebooks at www.diybeadingclub.com:
