assebly guide - prusa i3
TRANSCRIPT
-
7/24/2019 Assebly Guide - Prusa I3
1/31
Assembly Guide
For Prusa I3
-
7/24/2019 Assebly Guide - Prusa I3
2/31
Y-axis
1. Motor for Y-axis
Find below parts kit for Y-axis, plus a stepper motor
Assemble as per below picture. Please use a nylon washer to separate motor from motor
holder of Y-axis.
Please pay attention to position and orientation of limit switch (as shown in below photo).
-
7/24/2019 Assebly Guide - Prusa I3
3/31
-
7/24/2019 Assebly Guide - Prusa I3
4/31
2. Y-axis timing belt holder
Find below parts kit
After assembling, it should look as below picture. (For the screw going through bearing: it
should be moderately fixed, not too tight, to allow bearing run at ease).
-
7/24/2019 Assebly Guide - Prusa I3
5/31
3. Y-axis frame
Find below parts kit
Upper rod length 395mm, lower grooved rod length 415mm.
After assembling, it should look as below picture.
-
7/24/2019 Assebly Guide - Prusa I3
6/31
Assembling of front part of printer:
-
7/24/2019 Assebly Guide - Prusa I3
7/31
After assembling, it should look as below picture.
Now we add the Y-axis stepper motor (now ready after we assembled it in step 1)behind the
front frame:
-
7/24/2019 Assebly Guide - Prusa I3
8/31
After assembling, it should look as below picture.
-
7/24/2019 Assebly Guide - Prusa I3
9/31
4 Assembling heat plate
Find below parts kit
Assemble timing belt holder as per below picture
-
7/24/2019 Assebly Guide - Prusa I3
10/31
After assembling, it should look as below picture.
Now we mount heat plate
Note: wire of plate should face towards stepper motor.
-
7/24/2019 Assebly Guide - Prusa I3
11/31
After mounting the heat plate, we insert linear bearing into the hole at ege of plate, use
nylon band to fix it tight in place, as shown in below picture:
-
7/24/2019 Assebly Guide - Prusa I3
12/31
Add timing belt to the structure, as per below photo:
Ends of belt fixed as per below picture:
-
7/24/2019 Assebly Guide - Prusa I3
13/31
After assembling, it should look as below picture.
-
7/24/2019 Assebly Guide - Prusa I3
14/31
Assembling X-axis
Find below parts kit:
Stepper motor, X-axis limit switch (long wire), and parts kit
-
7/24/2019 Assebly Guide - Prusa I3
15/31
-
7/24/2019 Assebly Guide - Prusa I3
16/31
Putting the spring in place
-
7/24/2019 Assebly Guide - Prusa I3
17/31
Wire of limit switch goes through below wire besides the stepper motor.
Pay attention to the orientation of the limit switch (as shown in above photo)
Find parts kit for the other side of X axis, as per below photo
-
7/24/2019 Assebly Guide - Prusa I3
18/31
Assemble as below drawing
-
7/24/2019 Assebly Guide - Prusa I3
19/31
Assembling holder for extruder
Find below parts kit
First we put two of M2.5 nuts on the holder, as below photo:
-
7/24/2019 Assebly Guide - Prusa I3
20/31
After assembling, it should look as below picture.
-
7/24/2019 Assebly Guide - Prusa I3
21/31
Assembling fixture unit for ends of timing belt:
On the left side we have the fixture terminal for timing belt; On the right, we have a
horizontal screw for adjusting tension of belt.
-
7/24/2019 Assebly Guide - Prusa I3
22/31
Assembling extruder
Specific procedures as follows:
First mount the aluminum block to stepper motor. Note: we need to put a washer between
block and the aluminum cylinder (as circled in below picture)
-
7/24/2019 Assebly Guide - Prusa I3
23/31
Mounting gear, bearing and spring:
Then we mount the set to a U-shaped aluminum holder.
(Note: please pay attention to direction of the stainless-steel feeder that goes through the
U-shape holder in below photo. The side with PTFE tube lining goes to the M6-hole of
extruder)
-
7/24/2019 Assebly Guide - Prusa I3
24/31
Mounting the heating unit and fan:
-
7/24/2019 Assebly Guide - Prusa I3
25/31
Assembling main frame of printer
Please pay attention to sequence: first put the acrylic parts together then assemble Z-axis,
otherwise we might be blocked by screw.
Note: there are two triangle-shaped plates. They are different: the one with 3-holes is for
assembling power supply. The one with four is for circuit.
-
7/24/2019 Assebly Guide - Prusa I3
26/31
Z-axis and stepper motor
Find below parts kit:
Add below printed parts to the acrylic plate
-
7/24/2019 Assebly Guide - Prusa I3
27/31
After assembling, it should look as below photo:
-
7/24/2019 Assebly Guide - Prusa I3
28/31
Assembling Z-axis motor: find below parts kit:
Assemble as below picture:
Note: before adding motor in place, we need to put nylon washers for buffering.
-
7/24/2019 Assebly Guide - Prusa I3
29/31
Then we can mount motor and limit switch.
Note: orientation of limit switch should be as below picture shows:
-
7/24/2019 Assebly Guide - Prusa I3
30/31
Then we add X-axis to Z-axis, as per below photo:
In the end, we add Y-axis to the acrylic frame, as shown in below picture:
-
7/24/2019 Assebly Guide - Prusa I3
31/31
Here below shows how to fix the triangle-shaped acrylic plates:
Picture below shows how to fix the Y-axis rod:
End of assembly guide.