q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q. q....

93
© Lloyd’s Register Group Limited 2018. All rights reserved. This list identifies works approved by Lloyd’s Register Group Limited (LR) for steelmaking and the manufacture of rolled steel plate, strip, sections and bars in accordance with the requirements of LR's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The information listed for each works is a summary of the product, generic grade and maximum thickness, or in the case of round bars, diameter approved. It is important to note that this list does not provide full details of the grades approved by LR as required by the Rules. The combinations of deoxidation practice (e.g. killed, semi-killed), micro-alloying and grain refining additions (e.g. Al, Al + Nb Al + Nb + V, etc.), in association with specific rolling procedures ( e.g. N or TM, etc.), are not included. These parameters may vary within each grade by manufacturer and could influence the fabrication procedures that can be applied. The list also includes firms approved for the manufacture of fabricated steel sections. Where required this information should be obtained from the current certificate of approval issued to the manufacturer by LR. Works designated "MQS Approved" are also approved under the Materials Quality Scheme in accordance with LR's Rules for the Manufacture, Testing and Certification of Materials, Chapter 1 Section 2. Approval only covers the manufacturing location listed, it does not extend to other works owned by the same company. The local LR surveying office is also listed. Abbreviations: B.O.S. Basic Oxygen Steelmaking Con Cast Continuous Casting E.A.F. Electric Arc Furnace O.H. Open Hearth Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as 'Lloyd's Register'. Lloyd's Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract. List 1 Approved Steelmakers and Manufacturers of Rolled Steel Plates, Strip, Sections & Bars As at 10 April 2018

Upload: truongtu

Post on 30-Mar-2018

404 views

Category:

Documents


7 download

TRANSCRIPT

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

This list identifies works approved by Lloyd’s Register Group Limited (LR) for steelmakingand the manufacture of rolled steel plate, strip, sections and bars in accordance with therequirements of LR's Rules for the Manufacture, Testing and Certification of Materials,Chapter 3.

The information listed for each works is a summary of the product, generic grade andmaximum thickness, or in the case of round bars, diameter approved.

It is important to note that this list does not provide full details of the grades approved byLR as required by the Rules. The combinations of deoxidation practice (e.g. killed,semi-killed), micro-alloying and grain refining additions (e.g. Al, Al + Nb Al + Nb + V,etc.), in association with specific rolling procedures ( e.g. N or TM, etc.), are not included.These parameters may vary within each grade by manufacturer and could influence thefabrication procedures that can be applied.

The list also includes firms approved for the manufacture of fabricated steel sections.

Where required this information should be obtained from the current certificate of approvalissued to the manufacturer by LR.

Works designated "MQS Approved" are also approved under the Materials Quality Schemein accordance with LR's Rules for the Manufacture, Testing and Certification of Materials,Chapter 1 Section 2.

Approval only covers the manufacturing location listed, it does not extend to other worksowned by the same company. The local LR surveying office is also listed.

Abbreviations:

B.O.S. Basic Oxygen SteelmakingCon Cast Continuous CastingE.A.F. Electric Arc FurnaceO.H. Open Hearth

Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers,employees or agents are, individually and collectively, referred to in this clause as 'Lloyd'sRegister'. Lloyd's Register assumes no responsibility and shall not be liable to any personfor any loss, damage or expense caused by reliance on the information or advice in thisdocument or howsoever provided, unless that person has signed a contract with therelevant Lloyd's Register entity for the provision of this information or advice and in thatcase any responsibility or liability is exclusively on the terms and conditions set out in thatcontract.

List 1

Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

As at 10 April 2018

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Australia

As belowB.O.S. / Con CastSteelmakingBLUESCOPE STEEL (AIS) PTY. LTD. SydneyA, B, D, E 51Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

51Higher Strength

A, B, D, E 13Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

6Higher Strength

P.O. Box 1854Wollongong

Port Kembla Steelworks

Tel: +61 2 42754666 Fax: +61 2 42753045 Email: [email protected] with specified through thickness properties notation Z35 may be added.Normalizing heat treatments carried out by sub-contractor, Bisalloy.

Certificate # MD00/1929/0009/1 Expiry date: 28/07/2018

NSW 2500

Austria

As belowE.A.F./V.O.D./IngotSteelmakingBREITENFELD EDELSTAHL AG Viennacarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless

120Ingots (tonnes)Semi-Finished

8662 St. Barbara im MürztalBreitenfelderstrasse 22

Tel: +43 (0)3858 6161 231 Fax +43 (0)3858 6161 248 Email mailto:[email protected]: http://www.breitenfeld.atCertificate # MD00/3255/0005/1 Expiry Date: 06/06/2018Including VD/VOD

A, B, D, E 20Normal StrengthSectionsBÖHLER PROFIL GmbH ViennaAH32, AH36, DH32, DH36, EH32, EH36 20Higher StrengthA, B, D, E 20Normal StrengthBarsAH32, AH36, DH32, DH36, EH32, EH36 20Higher Strengthcarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless

20Structural

Waidhofnerstraße 83333 BöhlerwerkTel: +43 7448 7007 24504 Fax: +43 7448 7007 24602 email: [email protected] web: www.bohler-profil.com

Certificate #: MD00/0202/0007/1 Expiry date: 27/01/2018

High alloy bars and sections may be accepted for approved applications.

As below 38VAR/INGOTSteelmakingSONDERSTAHLWERK BREITENFELD GmbH Viennacarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless

38Ingots (tonnes)Semi-Finished

carbon, carbon-manganese, alloy, austeniticstainless, duplex

38IngotsESR

8662 St. Barbara im MürtztalBreitenfelderstasse 22

Tel +43 (0)3858 6161 231 Fax +43 (0)3858 6161 248 Email [email protected] Web http://www.breitenfeld.at

Certificate # MD00/3256/0005/1 Expiry date: 06/06/2018Including remelting of Ni materials

A 120Normal StrengthBarsSTAHL JUDENBURG GmbH Viennacarbon, carbon-manganese 120Structuralcarbon, carbon-manganese, carbon-manganese 120Machinery

Gußstahlwerkstrasse 21A-8750 JudenburgTel: +43 3572 701-358 Fax: +43 3572 701-248

E-mail: [email protected]

Website: www.stahl-judenburg.com

Certificate No: MD00/1643/0008/1 Expiry date: 27/01/2021

As at 10 April 2018 2Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowE.A.F./Ingot/Con CastSteelmakingVOESTALPINE BÖHLER EDELSTAHL GmbH & CoKG

Vienna

carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless

220StructuralBars

Postfach 96A-8605 Kapfenberg

Mariazellerstraße 25

Tel: +43 3862 20 36698 Fax: +43 3862 20 37559email: [email protected] web: ww.bohler-edelstahl.comCertificate #: MD00/0200/0009/1 Expiry date: 20/01/2021

carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingVOESTALPINE STAHL DONAWITZ GmbH Viennacarbon, carbon-manganese, alloy 283Blooms/BilletsSemi-Finished

A 8700 LeobenKerpelystraße 199

Tel: +43 50304 25-4659 Fax: +43 50304 65-2464 Email: mailto:[email protected] Web:http://www.voestalpine.com/stahldonawitzCertificate #: MD00/2976/0005/1 Expiry date: 20/04/2018

As belowB.O.S. / Con CastSteelmakingvoestalpine Grobblech GmbH ViennaA, B, D, E 140Normal StrengthPlatesAH42, DH42, EH42 55Higher StrengthAH40, DH40, EH40, FH40 100AH32, AH36, DH32, DH36, EH32, EH36, FH32,FH36

140

360AR 40Boiler & Pressure Vessel410AR 50360FG, 410FG, 460FG, 490FG, 510FG 1401.5Ni, 3.5Ni, 5Ni, 9Ni 50Ferritic Low TemperatureLTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36

140

D/304L 50Clad

P.O Box 3Voest.- Alpine - Str. 3

Tel: +43 50304 15 9091 Fax: +43 50304 55 9091Email: [email protected] Web: www.voestalpine.com

Certifcate No. MD00/1614/0010/1 Expiry date: 28/07/2020

Approval includes the supply of z25 and z35 grades.

Approval includes pressed heads.

A-4020 Linz

Belarus, Republic of

As belowE.A.F./V.O.D./Con CastSteelmakingOJSC "Byelorussian Steel Works-ManagementCompany of

St. Petersburg

Carbon, Carbon-Manganese 140Rolled BilletsSemi-Finished

carbon, carbon-manganese, Normal Strength 300Billets

37, Promyshlennaya Str.BY- 247210 Zhlobin,

"Byelorussian Metallurgical Company" holding"(OJSC "BSW -management company of "BMC" holding")

Tel No: +375 2334 56180 Fax no: +375 2334 56317 Mob +375 291105030Email : mailo: [email protected]: www.bmz.gomel.byCertificate No: MD00/4297/0002/1 Expiry date 04/03/2020

Gomel Region,

As at 10 April 2018 3Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Belgium

As belowE.A.F./A.O.D./Con CastSteelmakingAPERAM STAINLESS BELGIUM - CHATELET site Antwerpaustenitic stainless 200SlabsSemi-Finished

14, Rue des Ateliers6200 ChateletTel: +32 (0) 7160 7214 E-mail: [email protected]

Website: www.aperam.com

Certificate Number: MD00/4387/0003/1 Expiry: 16/09/2020

austenitic stainlessE.A.F./A.O.D./Con CastSteelmakingAPERAM STAINLESS STEEL EUROPE- Genk site Antwerpaustenitic stainlessE.A.F./V.O.D./Con Castaustenitic stainless 200SlabsSemi-Finished304L, 304LN, 316L, 316LN, 321, 347 14Austenitic StainlessPlates

Swinnenwijerweg 5B-3600 GenkTel: +32 89 30 1959 E-mail: [email protected]

Website: www.aperam.com

Certificate No: MD00/3423/0005/1 Expiry date: 27/01/2020

As belowE.A.F. / Con CastSteelmakingINDUSTEEL BELGIUM SA AntwerpA, B, D, E 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36, EH40 50Higher StrengthDH42, DH46, DH50, DH55, DH62, DH69, EH42,EH46, EH50, EH55, EH62, EH69, FH42, FH46,FH50, FH55, FH62, FH69

100

360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, 5Ni, 9Ni

50Ferritic Low Temperature

304L, 304LN, 316L, 316LN 50Austenitic StainlessUNS S31803(MOD)* 40Duplex Stainless

266, Rue de ChâteletB-6030 Charleroi

ARCELOR MITTAL GROUP

Tel: +32 47 8 80 35 19 Fax: +32 71 44 19 29

E-mail: [email protected]

Website: http://www.industeel.arcelormittal.com

Plates in grades LTAH32; LTAH36; LTDH32; LTDH36; LTEH32; LTEH36; 5%Ni; 9%Ni over 40mm thickness and up to the maximum thickness stated above areaccepted for approved applications only.* accepted for approved applications.Higher strength grades supplied in the quenched and tempered grades are accepted with specified through thickness properties designation Z35.

Certificate Number: MD00/0477/0011/1 Expiry: 07/07/2020

A, B, D, E 120Normal StrengthPlatesNLMK CLABECQ S.A. AntwerpAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

120Higher Strength

360AR, 410AR 25Boiler & Pressure Vessel360, 410 50360FG, 410FG, 460FG, 490FG, 510FG 120

Rue de Clabecq, 101B-1460 IttreTel: +32 3919227 Fax: +32 3919883 Mobile +33 4972 297369

Email:[email protected]

Web:http://www.eu.nlmk.com

MQS Approved - Approval No. MQS016

Certificate #: MD00/2204/0013/1 Expiry date: 23.06.2018

As at 10 April 2018 4Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Brazil

carbon, carbon-manganeseB.O.S. / Con CastSteelmakingARCELORMITTAL BRAZIL S/A (ARCELORMITTALTUBARÃO )

Rio de Janeiro

carbon, carbon-manganese 250SlabsSemi-Finished

D 16Normal StrengthHot Rolled Coil

A, B 19

AH36 16Higher Strength

AH27S, AH32 19

510FG 16Boiler & Pressure Vessel

360FG, 410FG, 460FG, 490FG 19

D 16Normal StrengthPlates from coils

A, B 19

AH36 16Higher Strength

AH27S, AH32 19

460 FG, 490FG 16Boiler and Pressure Vessel

410 FG, 360 FG 19

526 - Polo Industrial Tubarão,Distrito de Carapina Serra E.S - CEP 29160-904

Avenida Brigadeiro Eduardo Gomes,

Carbon and carbon-manganese grades cover the following LR normal and higher tensile strength grades. A, B, D, E, AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

Tel: +55 27 3348 3215 Fax: +55 27 3348 2211

E-mail: [email protected]

Website: www.arcelormittal.com/br/tubarao

Material Quality Scheme approved, MQS 054

Certificate No: MD00/0342/0013/1 Expiry date: 28/06/2020

As belowB.O.S. / Con CastSteelmakingCSP - COMPANHIA SIDERURGICA DO PECÉM Rio de JaneiroNormal strength, Higher Strength 300SlabsSemi-Finished

Rodovia, Ce 155 s/n - km 11,5 CEP 62674-000,

Tel: +55 85 31048001email: [email protected] web: www.cspecem.com

Certificate No: MD00/4676/0001/1 Expiry Date: 18/04/2020

São Gonçalo do Amarante (CE),

As belowB.O.S./Ingot/Con CastSteelmakingGERDAU AÇOMINAS S.A. Rio de JaneiroCarbon, Carbon-Manganese, Alloy 180Rolled BilletsSemi-Finishedcarbon, carbon-manganese, alloy 250Slabscarbon, carbon-manganese, alloy 300Bloomscarbon, carbon-manganese, alloy 180BilletsCarbon, Carbon-Manganese, Alloy 280Rolled BloomsA, B 50Normal StrengthPlatesA 20Normal StrengthHot Rolled Coil

Rodovia MG-443 KM 7Fazenda do Cadete

Tel: +55 32 3749 5637 Mob: +55 31 9 8391 0098email: [email protected] web www.gerdau.com.br

Certificate #: MD00/2071/0010/1 Expiry date: 24/02/2021

36420-000-Ouro Branco-MG

As belowB.O.S. / Con CastSteelmakingUSIMINAS Rio de JaneiroA, B, D, E 50Normal StrengthPlatesAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40

50Higher Strength

360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50A 12Normal StrengthHot Rolled Coil

As at 10 April 2018 5Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Brazil360, 410 12Boiler & Pressure VesselHot Rolled CoilUSIMINAS Rio de Janeiro

Av. Pedro Linhares Gomes, 5431Distrito Usiminas, CEP 35160-900

Usinas Siderúrgicas de Minas Gerais S/AUsina Intendente Câmera

Tel +55 (0)31 38293264 Fax +55 (0)31 38293516

E-mail: [email protected]

Z25 and Z35 through thickness properties for plates of approved grades in the TM+Acc and TM+Acc+Temper conditions

Materials Quality Scheme Approved - MQS 014

Certificate No: MD00/1603/0010/1 Expiry date: 22/06/2020

Ipatinga, Minas Gerais

As belowB.O.S. / Con CastSteelmakingUSINAS SIDERÚRGICAS DE MINAS GERAIS S.A. -USIMINAS

São Paulo

A, B, D, E 80Normal StrengthPlates

AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

80Higher Strength

360AR, 410AR 40Boiler & Pressure Vessel

360FG, 410FG, 460FG, 490FG, 510FG 80

Rodovia Cônego Domênico Rangoni, Km 6Vila da Indústrias 11573-900

Tel: +55 13 3362-2978 Fax: +55 13 3362-3775 Email: mailto: [email protected] Web:http://www.usiminas.comSpecified through thickness properties for plates in the normalised condition, rolled from ingots, up to 35 mm thickness.Specified through thickness properties for plates of grades up to DH32 and thickness up to 26mm in the normalised condition, rolled from continuously castslab.Material Quality Scheme approved, MQS 044Certificate #: MD00/1193/0009/1 Expiry date: 28/09/2017

Cubatão - São Paulo

Bulgaria

carbon, carbon-manganeseE.A.F. / IngotSteelmakingRADOMIR METAL INDUSTRIES JSC Sofiacarbon, carbon-manganese 25Ingots (tonnes)Semi-Finished

2400 Radomir,Tel: 359 77780489 Fax: 359 77782134email: [email protected] web: radomir-metal-industries.com

Certificate No: MD00/4386/0001/1 Expiry Date: 17/09/2017

As belowE.A.F. / Con CastSteelmakingSTOMANA INDUSTRY AD SofiaAs below 200Blooms/BilletsSemi-FinishedA 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 40

1, Vladaysko Vastanie Str.2304 PernikTel: +359 766 81028 Fax: +359 766 81952email:[email protected] web: www.stomana.bgCertificate #: MD00/1868/0010/1 Expiry date: 16/04/2019

As at 10 April 2018 6Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Canada

As belowB.O.S. / Con CastSteelmakingESSAR STEEL ALGOMA INC. Torontocarbon, carbon-manganese 205SlabsSemi-FinishedD, E 50Normal StrengthPlatesA, B 60AH32, AH36, DH32, DH36, EH32, EH36 65Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 65Boiler & Pressure Vessel

Sault Ste. MarieOntario

105 West Street

Tel +1 705 945 2347 Fax: +1 705 945 2632 e-mail: [email protected] web: www.essarsteelalgoma.com

Certificate #: MD00/0092/0009/1 Expiry date: 04/05/2020

P6A 5P2

As BelowEAF/LMF/Con CastSteelmakingEVRAZ NORTH AMERICA Vancouver BCA, B, AH36, DH36 200SlabsSemi-Finished

Regina, SKS4P 3C7

EVRAZ Regina Steel100 Armour Road

Tel: +1 800 667 1616 and 306 924 7500 Email to: [email protected] Web: http://www.evrazna.com

Slabs as semi-finished products of nominal dimensions 8" x 84" x 480" are approved

MATERIALS QUALITY SCHEME APPROVED - MQS 055Certificate No. :MD00/4490/0001/1 Expiry Date: 16/6/2018:

As belowE.A.F. / Con CastSteelmakingGERDAU LONGSTEEL NORTH AMERICA TorontoA, B 15Normal StrengthSectionsAH27S, AH32, AH36 15Higher Strength

WhitbyOntario

Whitby Steel Mill Operations1 Gerdau Court

Tel: +1 905 668 8811 ext 4055 Fax: +1 905 668 3742 Email: mailto:[email protected] Web: http://www.gerdau.comCertificate #: MD00/0322/0009/1 Expiry date: 29/01/2020CSA grades 260W, 300W and 350W may be accepteed for approved applications equivalent to the appropriate Lloyds Register grade above

L1N 5T1

China, People's Republic of

As belowE.A.F./A.O.D./Con CastSteelmakingANGANG LIANZHONG STAINLESS STEELCORPORATION

Guangzhou

duplex stainless 200SlabsSemi-Finished

East Section,Economy & Technology Development Zone,

No. 1 Lianguang Road,

Tel: +86 (0)20 2220 8888 Fax: +86 (0_20 3210 7529email: [email protected] web: www.lisco.com.cn

Certificate No: MD00/4706/0001/1 Expiry Date: 04/09/2020

Guangzhou,

A, B, D, E 100Normal StrengthPlatesANGANG STEEL COMPANY LIMITED DalianAH42, AH46, AH50, AH55, DH42, DH46, DH50,DH55, EH42, EH46, EH50, EH55, FH42, FH46,FH50, FH55

80Higher Strength

AH27S, AH32, AH36, DH27S, DH32, DH36,DH40, EH27S, EH32, EH36, EH40, FH27S, FH32,FH36, FH40

100

360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,9Ni

40Ferritic Low Temperature

UNS S31803 40Duplex Stainless

As at 10 April 2018 7Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Honqi Road, Lishan District,Anshan City,

HEAVY PLATE MILL OF MEDIUM AND HEAVY PLATE PLANT

Tel: +86 412 673 4836 Fax: +86 412 672 5766 Email mailto:[email protected] Web http://www.ansteel.con.cnAll grades and thicknesses accepted with specified through thickness properties, Z25 and Z35 designations.Certificate Number: MD00/1869/0012/1 Expiry: 20/03/2018

Liaoning Province

As belowB.O.S. / Con CastSteelmakingANGANG STEEL COMPANY LIMITED DalianNormal strength, Higher Strength 300SlabsSemi-FinishedNormal Strength, Higher Strength 320BilletsA, B, D 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360AR, 410AR 20Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 40

Angang AreaAnshan City

MEDIUM PLATE MILL OF MEDIUM AND HEAVY PLATE PLANT

Tel +86 0412 675 1030 Fax +86 0412 675 2819 Email: [email protected] as semi finished products nominal 2000mm width x nominal 7000mm length to the above maximum thickness are approved.Concast billets approved to 320 x 410mm section size.Certificate No. MD00/2757/0009/1 Expiry date: 21/10/2020

A, B, D 20Normal StrengthHot Rolled CoilANGANG STEEL COMPANY LIMITED DalianAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

20Higher Strength

360FG, 410FG, 460FG, 490FG, 510FG 20Boiler & Pressure Vessel

Anshan CityLiaoning Province

HOT STRIP MILL OF ANGANG STEEL COMPANY LIMITEDAngang Production Area,Tiexi District

Tel: +86 412 6757143 Fax: +86 412 6753575Email: [email protected] http://www.ansteel.com.cnCertificate #: MD00/3301/0004/1 Expiry date: 01/01/2019

114024

As belowB.O.S. / Con CastSteelmakingANGANG STEEL COMPANY LIMITED Daliancarbon-manganese, carbon, carbon manganese 300Blooms/BilletsSemi-FinishedA, B, D, E 100Normal StrengthPlatesAH32, AH36, AH40, DH32, DH36, DH40, EH32,EH36, EH40

100Higher Strength

360FG, 410FG, 460FG, 490FG, 510FG 40Boiler & Pressure Vessel5Ni, 9Ni 60Ferritic Low Temperature

115000 BayuquanYingkou City

BAYUQUAN 5500 HEAVY PLATE MILL

Tel: +86 417 8680153 Fax: +86 417 8680141email: [email protected] web: www.ansteel.com.cnCertificate No. MD00/3595/0004/1 Expiry date: 09/05/2018

Liaoning Province

A, B, D 20Normal StrengthSectionsANGANG STEEL COMPANY LIMITED DalianAH32, AH36, DH32, DH36 20Higher Strength

114021 Tiexi,Anshan City,

HEAVY SECTION PLANT OF ANGANG STEEL COMPANY LIMITE

Tel: +86 412 673 4836 Fax: +86 412 672 5766 email [email protected] web www.ansteel.con.cn

Certificate No: MD00/4637/0001/1 Expiry Date: 01/12/2019

Liaoning Province,

As belowE.A.F./V.O.D./IngotSteelmakingANSTEEL STEEL CASTING CO., LTD. Daliancarbon, carbon-manganese, alloy 100Ingots (tonnes)Semi-Finished

Anshan, Liaoning Province11042

West Side of Hongqi Road

el: +86 412 6765212/6765217 Fax: +86 412 6765218 Email to: [email protected] Web http://www.angangzhongji.com.cn

Certificate #: MD00/4436/0001/1 Expiry date: 25/02/2018

As BelowB.O.S./E.A.F./Con CastSteelmakingANYANG IRON & STEEL CO., LTD. WuhanNormal strength 230SlabsSemi-FinishedA, B, D 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 36Higher Strength360AR, 410AR, 460FG, 490FG, 510FG 36Boiler & Pressure Vessel360FG, 410FG 40A, B 12Normal StrengthSections

As at 10 April 2018 8Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Anyang CityHenan Province

Yindu District

Tel: +86 372 3120051 Fax: +86 372 3120177 email: [email protected] web: www.anyang.com.cnCertificate #: MD00/2200/0010/1 Expiry date: 18/01/2019

A, B and D grades in the normalised condition approved for through thickness properties with Z25 and Z35 notation.

As belowB.O.S. / Con CastSteelmakingBAOSHAN IRON & STEEL CO., LTD. Shanghai PortAs belowB.O.S. / Ingotcarbon, carbon-manganese 500SlabsSemi-Finishedcarbon, carbon-manganese, Alloy 500Blooms/BilletsA, B, D, E 130Normal StrengthPlatesAH40, DH40, EH40, FH27S, FH32, FH36 68Higher StrengthDH36S 90AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

100

AH42, AH46, AH50, AH55, AH62, AH69, DH42,DH46, DH50, DH55, DH62, DH69, EH42, EH46,EH50, EH55, EH62, EH69, FH40, FH42, FH46,FH50, FH55, FH62, FH69

160

360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure Vessel9Ni 50Ferritic Low TemperatureLTAH40, LTDH40, LTEH40, LTFH27S, LTFH32,LTFH36, LTFH40

68

LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36

80

A, B, D 22Normal StrengthHot Rolled CoilAH32, AH36 12Higher Strength460FG, 490FG, 510FG 12Boiler & Pressure Vessel360FG, 410FG 22R5 210Chain Cable StockBars

No 885, Fujin RoadBaoshan District

Core Base

Tel +86 21 2664 5085 Fax +86 21 2664 4886

E-mail: [email protected]

Web:http://www.baosteel.com

Including all plate grades and thicknesses with specified through thickness properties (Z35)

Certificate #: MD00/1343/0019/1 Expiry date: 29/03/2019

Materials Quality Scheme Approved - MQS 038

Shanghai 201900

austenitic stainless steel, Fe-36Ni*E.A.F/A.O.D/L.A.F/ConCastSteelmakingBAOSTEEL SPECIAL METALS Co., LTD Shanghai PortFe-36Ni* 8Fe-Ni alloysPlates

Baoshan District,Shanghai.

No. 1269, Shuichan Road,

Tel: +86 - 21 - 2603 2450 Fax: +86 - 2603 2284

E-mail:

www.baosteel.com

Certificate No: MD00/4729/0001/1 Expiry Date: 30/10/2020

200940

As belowB.O.S. / Con CastSteelmakingBAOSTEEL ZHANJIANG IRON & STEEL Co., Ltd. Guangzhoucarbon, carbon-manganese 250SlabsSemi-FinishedD 35Normal StrengthPlatesA, B 50AH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 40Boiler & Pressure Vessel

Dongjian Town, Donghai Island, ZhanjiangGuangdong Province

Baosteel Zhanjiang Iron & Steel Plant

Tel: +86 0759 3525503 Fax: +86 0759 3525555Email: Web: www.baosteel.comCertificate No.: MD00/4683/0001/1 Expiry Date: 24/07/2020

As at 10 April 2018 9Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

A, B, D 14Normal StrengthSectionsCHANGSHU LONGTENG SPECIAL STEEL CO., LTD. JiangyinAH27S, AH32, AH36 14Higher Strength

Meili TownChangshu City

No. 9 Jusha Road

Tel: +86 0512 5206 1085 Fax: +86 0512 5266 1141 Email: [email protected] Web: http://www.lttg.cnCertificate #: MD00/3275/0005/1 Expiry date: 09/10/2018

Jiangsu Province 21551

As belowB.O.S. / Con CastSteelmakingCHANGSHU LONGTENG SPECIAL STEEL CO., LTD. JiangyinAs belowE.A.F. / Con Castcarbon, carbon-manganese, alloy 26Ingots (tonnes)Semi-FinishedNormal Strength, Higher Strength 260BloomsNormal Strength, Higher Strength 200BilletsD 15Normal StrengthSectionsE 16A, B 20DH32, DH36, EH32, EH36 16Higher StrengthAH27S, AH32, AH36 20

Tonggang Industrial Park,Meili Town, Changshu City,

118 Hualian Road,

Tel.:+86 0512 5206 1085 Fax.: +86 512 5266 1141Email: [email protected] Web: http://www.lttg.cn

Certificate #: MD00/3976/0003/1 Expiry date: 07/12/2017

Blooms as semi finished products nominal 340mm width x nominal 12000mm length Billet approval covers BOS/Concast billets to 200 x 310mm section size x 6000mm nominal length..

Jiangsu Province 215511

As belowB.O.S. / Con CastSteelmakingCHENGDE JIANLONG SPECIAL STEEL CO., LTD. Qingdaocarbon, carbon-manganese, Alloy 200Blooms/BilletsSemi-FinishedU2, U3 90Chain Cable StockBars

Ping-an-bao TownXinglong County

Tel.:+86 0314 5316388 Fax.: +86 314 5316389Email: [email protected] Web: http://www.ejianlong.com

Certificate #: MD00/4550/0002/1 Expiry date: 10/02/2019

Chengde, Hebei

As belowB.O.S. / Con CastSteelmakingCISCO WuhanNormal strength, Higher Strength 300SlabsSemi-FinishedA, B, D, E 80Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

80Higher Strength

360AR, 410AR, 460AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG 80

Changshou DistrictChongqing

Chongqing Iron and Steel Co., Ltd.Jiangnan Town (4100 Mill)

Tel: +86 23 6887 3543 Fax: +86 23 6887 3543email: [email protected] web: www.cqgt.comCertificate Number: MD00/3763/0007/1 Expiry date: 27/03/2019

A, B, D, E 40Normal StrengthPlatesCISCO WuhanAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

40Higher Strength

360AR, 410AR, 360FG, 410FG, 460FG, 490FG,510FG

40Boiler & Pressure Vessel

Chongqing Iron and Steel Co., Ltd.Jiangnan Town (2700 Mill)Tel: +82 623 6887 3543 Fax: +82 623 6887 3543 Email: [email protected] Web: http://www.cqgt.cnPlates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied to all Grades and supply conditions.Certificate Number: MD00/3982/0003/1 Expiry: 25/01/2018

As belowB.O.S. / Con CastSteelmakingDAYE SPECIAL STEEL CO., LTD. WuhanAs belowE.A.F./Ingot/Con Castcarbon, carbon-manganese, alloy 40Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 410Billetscarbon, carbon-manganese, alloy 650Barscarbon, carbon-manganese 190StructuralBarscarbon, carbon-manganese, alloy 250MachineryU1, U2, API-2F 110Chain Cable StockU3, R3S, R4 160

As at 10 April 2018 10Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Huangshi CityHubei Province

316 Huangshi Avenue

Tel: +86 714 629 7888 Fax: +86 714 629 7781 Email: [email protected] Web: http://www.dayesteel.com.cn

Mooring grade bars (grade R4) are restricted in ingot cast condition to supply to Zhengmao Group Co., Ltd.Mooring grade bars (grade R3S) are restricted to supply to Foshan Marine Anchor Chain Ltd. (FMAC)The bars may supply in annealing, normalized or quench and temperted conditions when it is appropriate

Certificate Number: MD00/2493/0011/1 Expiry: 11/08/2020

Post code: 435001

carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingDONGBEI SPECIAL STEEL GROUP Daliancarbon, carbon-manganeseE.A.F./Ingot/Con Castcarbon, carbon-manganese 5Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 450Blooms/Billetscarbon, carbon-manganese 200Barscarbon, carbon-manganese 200StructuralBarsU1, U2, U3 130Chain Cable Stock

Qiqihar CityHeilongjiang Province

BEIMEN SPECIAL STEEL CO., LTD.Fularji District

Tel: +86 452 680 1271 Fax: +86 452 680 1234 email: [email protected] web: www.bg.bmsteel.com

Certificate No: MD00/2907/0002/1 Expiry date: 29/07/2020

Carbon, Carbon-manganese, Alloy 27EAF/LRF/VD/IngotSteelmakingDONGBEI SPECIAL STEEL GROUP Daliancarbon, carbon-manganese, alloy 27Ingots (tonnes)Semi-Finished

Wanghua District,Fushun City,

FUSHUN SPECIAL STEEL CO. LTD.,East No 8 Anshan Road,

Tel No: +86 413 668 9161-3668 Fax no: +86 413 6674090Web: www.dtsteel.comCertificate No MD00/3945/0003/1 Expiry date: 04/09/2020

Liaoning Province

carbon, carbon-manganese, alloy 100B.O.S. / IngotSteelmakingDONGBEI SPECIAL STEEL GROUP Daliancarbon, carbon-manganese, alloy 100E.A.F. / Ingotcarbon, carbon-manganese, alloy 100Ingots (tonnes)Semi-Finished

Dalian Dengshahe Coastal Industrial Zone,Jinzhou New District,

DALIAN SPECIAL STEEL CO., LTD.No. 18 South Hebin Road,

Tel: +86 0411 626 93145 Fax: +86 0411 626 93037web: www.dsteel.com

Certificate No: MD00/4651/0001/3 Expiry Date: 11/01/2020

Dalian, Liaoning Province,

As belowB.O.S. / Con CastSteelmakingFUJIAN SANSTEEL MINGUANG CO., LTD. GuangzhouNormal strength, Higher Strength 250SlabsSemi-FinishedA, B 36Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 30Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 30Boiler & Pressure Vessel360, 410 36

Middle Gongyezhong RoadMeilie District

Tel: +86 598 8205138 Fax: +86 598 8205435Email: [email protected] Web: www.fjsg.com.cnCertificate #: MD00/3587/0006/1 Expiry date: 26/04/2018

Sanming CityFujian Province

austenitic stainless steel, duplex stainless steelE.A.F/A.O.D/L.A.F/ConCastSteelmakingGANSU JIU STEEL GROUP WuhanAs below 220SlabsSemi-Finished304L, 316L, 321 40Austenitic StainlessPlatesUNS S31803, UNS 32205* 40Duplex Stainless304L, 316L, 321 12Austenitic StainlessHot Rolled Coil

No.12, East Xiongguan Road, Jiayuguan City,Gansu Province

HONGXING IRON & STEEL CO., LTD

Tel: +86 0937 6717023 Fax: +86 0937 6714841Email: mailto: [email protected]: http://www.jiugang.comCertificate No.: MD00/4708/0001/1 Expiry date: 05/09/2020

As at 10 April 2018 11Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowB.O.S. / Con CastSteelmakingGUANGXI LIUZHOU GuangzhouA, B 36Normal StrengthPlatesAH27S, AH32, AH36 36Higher StrengthA, B 12Normal StrengthHot Rolled Coil

117 BeiqueLiuzhou

IRON & STEEL (GROUP) COMPANY

Tel: +86 (0)772 2596593 Fax: +86 (0)772 2592784email [email protected] web www.liuzousteel.com

Certificate #: MD00/2632/0007/1 Expiry date: 01/01/2018

Guangxi

As belowB.O.S. / Con CastSteelmakingHANBAO IRON & STEEL CO. LTD (HANSTEELGROUP)

Qingdao

Normal strength, Higher Strength 250SlabsSemi-Finished

A, B, D 18Normal StrengthHot Rolled Coil

AH27S, AH32, AH36, DH27S, DH32, DH36 18Higher Strength

A, B, D 18Normal StrengthPlates from coils

AH27S, DH27S, AH32, DH32, AH36, DH36 18Higher Strength

232,Fuxing Road,Handan,

Tel +86 310 6072202 Fax No. + 86 310 6072241Email [email protected] www.ligjt.com.cnCertificate No MD00/3874/0002/ 1 Expiry Date 09/01/2017

Hebei. 056015

As belowB.O.S. / Con CastSteelmakingHEBEI IRON & STEEL CO., LTD. QingdaoNormal strength, Higher Strength 220SlabsSemi-FinishedA, B, D, E 50Normal StrengthPlatesAH27S, DH27S, EH27S 38Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 50360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50

Handan CityHebei Province

Handan Branch232 Fuxing Road

Tel: +86 310 607 2202 Fax: +86 310 607 2241 Email: [email protected] Web: http://www.hgjt.com.cnSlabs as semi-finished products nominal 1800mm width x nominal 3200mm length to the above maximum thickness.Plates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied for approved grades supplied in the normalized conditionCertificate Number: MD00/1970/0010/1 Expiry: 03/03/2019

056015

As below 220B.O.S. / Con CastSteelmakingHEBEI JINGYE CUT DEAL CO., LTD. QingdaoNormal strength, Higher Strength 220SlabsSemi-FinishedA, B, D 30Normal StrengthPlatesAH27S, AH32, AH36, DH32, DH36 30Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 30Boiler & Pressure Vessel

Pingshan CountyShijiazhuang City

Nandian Town

Tel No +86 311 8287 3953 Fax No +86 311 82873988 Mob +86 158 3111 8888Email [email protected] www.hbjyjt.comCertificate No MD00/4022/0002/1 Expiry Date 08/05/2018

Hebei Province

As belowE.A.F. / Con CastSteelmakingHENGYANG VALIN STEEL TUBE CO., LTD. Wuhancarbon, carbon-manganese, alloy 800BilletsSemi-Finished

Hengyang CityHunan Province 421001

No. 10 Dalixincun

Tel: +86 734 8872188 Fax: +86 734 8873188

Email: [email protected]

Web: www.hysteeltube.com

Certificate #: MD00/3098/0003/1 Expiry date: 04/08/2019

As at 10 April 2018 12Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowB.O.S. / Con CastSteelmakingHUNAN VALIN LIANYUAN IRON & STEEL CO.,LTD.

Wuhan

carbon, carbon-manganese 230SlabsSemi-Finished

A, B, D 25Normal StrengthHot Rolled Coil

A, B, D 25Normal StrengthPlates from coils

Huangnitang, LoudiHunan Province

Tel +738 8661473 Fax +7388663570Email: [email protected]: www. lysteel.comCertificate #: MD00/3999/0002/1 Expiry date: 05/03/2018

Post Code: 417009

As belowE.A.F. / IngotSteelmakingINNER MONGOLIA NORTH Daliancarbon, carbon-manganese, alloy 8Ingots (tonnes)Semi-Finished

Baotou CityInner Mongolia

HEAVY INDUSTRIES GROUP CO., LTD.Binggong Road, Qingshan District

Tel No:+86 472 338 5318 Fax No: +86 472 332 3346email: [email protected] Including semi-finished as-forged bars to 8.5 tonnes in carbon, carbon-manganese and alloy steel for further processing by forging.

Certificate No: MD00/3099/0006/1 Expiry date: 06/08/2019

014033

carbon 20Structural SectionsSeamless HollowJIANGSU JIEDA SPECIFIC NEW MATERIAL CO LTD Jiangyin

No. 98 Gangcheng Road,Jiangyin City,

Jiangyin Plant

Tel No: + 00 86-510-8668775 Fax No: + 00 86-510-86687775/+00 510-86687229Email: [email protected]: www.jsjieda.com

Certificate No. MD00/4442/0002/01 Expiry Date: 17/01/2021

Jiangsu Province. 214400

As belowB.O.S. / Con CastSteelmakingJIANGSU SHAGANG GROUP NantongAs belowE.A.F. / Con Castcarbon, carbon-manganese 200BloomsSemi-Finishedcarbon, carbon-manganese 150Billetscarbon, carbon-manganese 500Barscarbon, carbon-manganese 100StructuralBarscarbon, carbon-manganese 100MachineryU2 140Chain Cable StockU3 210

Huai'an CityJiangsu Province

HUAIGANG SPECIAL STEEL CO., LTDNo. 188 South Xi'an Road

Tel: +81 517 83033307 Fax: +81 517 83033307 Mobile: +861536590 1758 Email:[email protected]

The approval for rolled bars over 60mm diameter is for steel manufactured by the B.O.S. / Con Cast route.Bars for chain cable stock are intended for final heat treated conditions; Grade U2 normalized; Grade U3 quenched and tempered.Chain cable stock bars may be accepted up to 250mm diameter may be accepted for further processing for forged chain cable fittings.Blooms, billets and bars as semi finished-products are approved for further processing for rolled products; blooms nominal maximum width 200mm x nominalmaximum length 12000mm; billets nominal maximum width 150mm x nominal maximum length 12000mm; bars nominal maximum length 12000mm; to theabove maximum thicknesses.Certificate Number: MD00/3240/0005/1 Expiry: 13/06/2015

As belowB.O.S. / Con CastSteelmakingJIANGSU SHAGANG GROUP CO., LTD Jiangyincarbon, carbon-manganese 320SlabsSemi-Finished

Jinfeng TownZhangjiagang City

Hongfa Steel PlantSteelmaking Plant Number 1

Tel: +86 512 5856 8791 Fax: +86 512 5855 8900 Email: [email protected] Web http://www.sha-steel.com

Certifcate Number: MD00/3127/0009/1 Expiry date: 27/10/2019

Materials Quality Scheme Approved - Approval No. MQS069

Jiangsu Province 215625

As at 10 April 2018 13Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

A, B, D, E 100Normal StrengthPlatesJIANGSU SHAGANG GROUP CO., LTD JiangyinAH27S, AH32, AH36, AH40, AH42, AH46,AH50, AH55, AH62, AH69, DH27S, DH32,DH36, DH40, DH42, DH46, DH50, DH55, DH62,DH69, EH27S, EH32, EH36, EH40, EH42, EH46,EH50, EH55, EH62, EH69, FH27S, FH32, FH36,FH40, FH42, FH46, FH50, FH55, FH62, FH69

100Higher Strength

360AR, 410AR, 460AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100

Hongfa Steel PlantSteel Plate Mill Line No. 1

Tel +86 0512 58568791 Fax: +86 0512 58558900 Email: [email protected] Web: http://www.sha-steel.com Plates in Grades A and B Fine Grain Al+Ti in the Normalising Rolled condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to60.0mm.Plates in Grades D and E Fine Grain Al+Ti+Nb in the TM+Acc condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to 60.0mm.Plates in the quenched and tempered supply condition >70mm thickness are accepted for approved applications only.Certificate No. MD00/3388/00010/1 Expiry date: 27/10/2019

Materials Quality Scheme Approved - Approval No. MQS069

Jiangsu Province, 215625

A, B, D, E 60Normal StrengthPlatesJIANGSU SHAGANG GROUP CO., LTD JiangyinAH27S, AH46S, DH27S, EH27S, EH46S, FH27S,FH32, FH36, FH40, FH46S, AH42S, DH42S,EH42S, FH42S, AH50S, DH50S, EH50S, FH50S,AH55S, DH55S, EH55S, FH55S, DH46S

60Higher Strength

EH47 80AH32, AH36, AH40, DH32, DH36, DH40, EH32,EH36, EH40

85

360AR, 410AR, 460AR, 360FG, 410FG, 460FG,490FG, 510FG

40Boiler & Pressure Vessel

LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36, LTFH40

40Ferritic Low Temperature

Hongfa Steel PlantSteel Plate Mill Line No. 2Tel +86 0512 5856 8791 Fax: +86 0512 5855 8900 Email: [email protected] Web: http://www.sha-steel.com All the above grades may be produced with specified through thickness tensile properties when manufactured and tested in accordance with LR Rules for'Plates with Specificed Through Thickness Properties'.Plates in Grades A and B Fine Grain Al+Ti in the Normalising Rolled condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to60.0mm.Plates in AH32 and AH 36 as rolled to 2800 x 11,000 and approved in the "as welded "conditionCertificate No. MD00/3913/0009/1 Expiry date: 27/10/2019

Materials Quality Scheme Approved - Approval No. MQS069

As belowB.O.S. / Con CastSteelmakingJIANGSU SHAGANG GROUP CO., LTD Jiangyincarbon, carbon-manganese 320SlabsSemi-Finished

Hongfa Steel PlantSteelmaking Plant Number 2

Tel: +86 512 5856 8791 Fax: +86 512 5855 8900 Email: [email protected] Web http://www.sha-steel.com

Certifcate Number: MD00/3923/0005/1 Expiry date: 27/10/2019

Materials Quality Scheme Approved - Approval No. MQS069

Jiangsu Province 215625

A, B, D, E 40Normal StrengthPlatesJIANGSU SHAGANG GROUP CO., LTD JiangyinAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 40Boiler & Pressure Vessel

Zhajiagang City

Hongfa Steel Plant3500mm Medium Plate Mill

Tel +86 0512 58568791 Fax: +86 0512 58558900 Email: [email protected] Web: http://www.sha-steel.com Certificate No. MD00/4710/0002/1 Expiry date: 18/06/2020

Jiangsu Province, 215625

Alloy 83EAF/LRF/VD/IngotSteelmakingJIANGSU SUNAN HEAVY MACHINERY JiangyinCarbon, Carbon-manganese 150

As at 10 April 2018 14Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Economic & Technology Development Zone,Changshu City,

TECHNOLOGY CO LTD.No.6 XingGang Road,

Tel: +85 0512 52275923 Fax: +86 0512 51923689email: [email protected]

Certificate No. MD00/4334/0002/1 Expiry Date: 09/06/2020

Jiangsu Province,

A, B 40Normal StrengthSectionsJIANGYIN BOFENG IRON & STEEL CO., LTD. JiangyinAH27S, AH32, AH36 40Higher Strength

Huaxicun Industrial ZoneJiangyin City

Tel: +86 13585066431 Fax: +86 510 8621 7672 Email: [email protected] Web: http://www.bofengsteel.cnThe approved sections are in the form of universal flats nominal widths <600mm to the maximum thickness shown above.Certificate Number: MD00/4031/0002/1 Expiry: 05/06/2018

Jiangsu Province

As belowE.A.F. / IngotSteelmakingJIANGYIN HUAQIANG SPECIAL STEEL Jiangyincarbon, carbon-manganese, alloy 32Ingots (tonnes)Semi-Finished

No. 18, Biangang Road,Huaxi, Jiangyin City,

CASTING & FORGING THERMOELECTRIC CO., LTD.

Tel: +86 510 862 10013 Fax: +86 510 862 03428 Mobile 0086 13812 582903 Email: [email protected] Ingots as semi finished products nominal 1240mm/1320mm diameter x 2770mm long to the above maximum weight are approved for further processing forforgings.Certificate Number: MD00/4013/0002/1 Expiry: 22/04/2018

Jiangsu Province, 214421,

carbon, carbon-manganese 34Structural SectionsSeamless HollowJIANGYIN TONGDA SPECIAL PIPEMANUFACTURE Co., Ltd.

Jiangyin

No. 18 Qiaohuang RD, Xiake TownJiangyin City

Tel: +86 (0)510 8657 3666 Fax: +86 (0)510 8656 0685email: [email protected] web: www.jytongda.comCertificate #: MD00/3853/0004/4 Expiry date: 02/11/2019

Jiangsu Province, 214408

As BelowB.O.S./E.A.F./Con CastSteelmakingJIANGYIN XINGCHENG SPECIAL STEEL WORKSCO., LTD.

Jiangyin

Normal strength 250SlabsSemi-Finished

carbon, carbon-manganese, alloy 390Blooms

carbon, carbon-manganese, alloy 900Semi-finished ProductsBars

carbon, carbon-manganese, alloy 180Structural

carbon, carbon-manganese, alloy 180Machinery

R4S 150Chain Cable Stock

U1, U2, U3 180

R3, R3S, R4 230

297, Bin Jiang East Road

Tel: +86 510 80676377 Fax: +86 510 86195042

E-mail: [email protected]

Web: http://www.jyxc.com

Certificate Number: MD00/2306/0018/1 Expiry: 24/09/2019

Jiangsu province 214429

As belowB.O.S. / Con CastSteelmakingJIANGYIN XINGCHENG SPECIAL STEEL WORKSCO., LTD.

Jiangyin

Normal strength, Higher Strength 300SlabsSemi-Finished

A, B, D, E 50Normal StrengthPlates

AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

50Higher Strength

360AR, 410AR 40Boiler & Pressure Vessel

360FG, 410FG, 460FG, 490FG, 510FG 50

As at 10 April 2018 15Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office3500 Plate Mill

Tel: +86 510 80676377 Fax: +86 510 86195042

E-mail: [email protected]

Website: www.jyxc.com

Certificate Number: MD00/3857/0007/1 Expiry date: 24/09/2019

Jiangsu Province 214429

A, B, D, E 80Normal StrengthPlatesJIANGYIN XINGCHENG SPECIAL STEEL WORKSCO., LTD.

Jiangyin

DH40, EH40, FH27S, FH32, FH36, FH40 60Higher Strength

AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

120

360AR, 410AR 40Boiler & Pressure Vessel

360FG, 410FG, 460FG, 490FG, 510FG 80

5Ni, 9Ni 50Ferritic Low Temperature

4300 Plate MillTel: +86 0510 80676377 Fax: +86 0510 6195042

E-mail: [email protected]

Website: http://www.jyxc.com

Plates in the Normalizing Rolled and Thermomechanical supply conditions are restricted to 3800mm maximum width. Plates in the TM+Acc supply condition are restricted to thickness from 16mm to the maximum thickness shown above.Z35 designation for through thickness properties may be added to all plates in the above supply conditions.

Certificate Number: MD00/3973/0005/1 Expiry date: 08/01/2021

carbon, carbon-manganese 16Structural SectionsFabricated SectionsJIGANG GROUP Co. LTD Qingdao

Licheng District,Jinan,

Airport Road,

Tel: +86 531 88842106 Fax: +86 531 62325025

E-mail: [email protected]

Website: www.jigang.com.cn

Certificate No. MD00/4595/0001/1 Expiry Date: 11/07/2019

Shangdong

304L, 316L 80Austenitic StainlessPlatesKUNSHAN DAEKYUNG STAINLESS STEEL CO.,LTD

Shanghai Port

Kunshan Economy Technology Development ZoneKunshan

No. 66 Longdeng Road

Tel:+86 512 57900998-8450 Fax: +86 512 57700372

E-mail: [email protected]

Website: www.kdkcsteel.com

Certificate #: MD00/3479/0004/1 Expiry date: 06/06/2020

Jiangsu Province

As belowB.O.S. / Con CastSteelmakingLAIWU STEEL GROUP LTD. YINSHAN SECTIONSTEEL CORPORATION

Qingdao

As below 300SlabsSemi-Finished

carbon, carbon-manganese 300Billets

A, B, D, E 80Normal StrengthPlates

DH40, EH40, FH32, FH36, FH40 50Higher Strength

AH32, AH36, DH32, DH36, EH32, EH36 80

360AR, 410AR 40Boiler & Pressure Vessel

360FG, 410FG, 460FG, 490FG, 510FG 80

As at 10 April 2018 16Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Gangcheng district,Laiwu,

Shuangquan Road,

Tel: +86 634 6821211 Fax: +86 634 6820824 email: [email protected] web: www.laigang.net

Certificate #: MD00/3855/0006/1 Expiry date: 06/11/2019

Shandong

As belowB.O.S. / Con CastSteelmakingMAANSHAN IRON & STEEL COMPANY LIMITED NanjingNormal strength, Higher Strength 220SlabsSemi-FinishedA, B 25Normal StrengthPlatesAH32, AH36, DH32, DH36 25Higher Strength360AR, 410AR 25Boiler & Pressure Vessel

No.8 Jiuhua West Road,Maanshan City

Tel: +86 555 287 7110 Fax: +86 555 2886 904 Email: [email protected] http://www.magang.com.cnCertificate #: MD00/0965/0008/1 Expiry date: 07/10/2018

Anhui Province PC:243000

Carbon, Carbon-manganese, Alloy 25EAF/LRF/VD/IngotSteelmakingMAANSHAN XINLONG SPECIAL STEEL CO., LTD. Jiangyincarbon, carbon-manganese, alloy 25Ingots (tonnes)Semi-Finished

Taibai Industrial,Dangtu town,

Tel: + 0555 667 5062 Fax: + 0555 667 5062

Certificate No: MD00/4402/0001/1 Expiry Date: 03/11/2017

Maanshan City,

As belowB.O.S. / Con CastSteelmakingMINMETALS YINGKOU MEDIUM PLATE CO., LTD. DalianNormal strength, Higher Strength 350SlabsSemi-FinishedA, B, D, E 100Normal StrengthPlatesAH27S, DH27S, EH27S 40Higher StrengthAH50, AH55, DH50, DH55, EH50, EH55 50AH42, AH46, DH42, DH46, EH42, EH46 80AH32, AH36, AH40, DH32, DH36, DH40, EH32,EH36, EH40, FH32, FH36, FH40

100

360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100

Laobian DistrictYingkou City

No 1 Fanrong Road, Yejin Street

Tel: 086 (0)417 3256051 Fax: 086 (0)417 3256057 Email mailto:[email protected] :www.wkyg.comPlates with specified through thickness properties in listed grades of normal and higher strength steels.Certificate #: MD00/2585/0009/1 Expiry date: 30/07/2020

Liaoning Province

As belowB.O.S. / Con CastSteelmakingNANJING IRON & STEEL CO., LTD. NanjingAs belowE.A.F. / Con CastNormal strength, Higher Strength 220SlabsSemi-FinishedNormal Strength, Higher Strength 320BloomsNormal Strength, Higher Strength 150BilletsA, B, D, E 100Normal StrengthPlatesAH27S, DH27S, EH27S, FH27S 60Higher StrengthEH47 80AH32, AH36, AH40, AH42, AH46, AH50, AH55,AH62, AH69, DH32, DH36, DH40, DH42, DH46,DH50, DH55, DH62, DH69, EH32, EH36, EH40,EH42, EH46, EH50, EH55, EH62, EH69, FH32,FH36, FH40, FH42, FH46, FH50, FH55, FH62,FH69

100

360AR, 410AR, 360, 410 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100LTAH27S, LTDH27S, LTEH27S, LTFH27S 40Ferritic Low TemperatureLTAH32, LTAH36, LTAH40, LTDH32, LTDH36,LTDH40, LTEH32, LTEH36, LTEH40, LTFH32,LTFH36, LTFH40, 5Ni, 9Ni

60

U1, U2, U3 180Chain Cable StockBars

As at 10 April 2018 17Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

XieJiaDianLuhe District

Nanjing Works

Tel: +86 25 5707 3657 Fax: +86 25 5707 4341 Email :[email protected] Web:http://www.njsteel.com.cn

Plates with specified through thickness properties may be accepted with the suffix Z35 applied to all approved grades

U2, U3 bars at 80mm diameter or less are produced by BOS or EAF steelmaking, bars over 80mm diameter are produced by EAF steelmaking.

Billets and blooms approved upto the above maximum thickness, 480mm width and nominal 12000mm length.

Slabs approved upto the above maximum thickness, 2510mm width and nominal 4000mm length.

Certificate Number: MD00/1065/0021/1 Expiry date: 12/10/2019

Nanjing, Post Code: 210035

As belowB.O.S./Ingot/Con CastSteelmakingNANYANG HANYE SPECIAL STEEL CO., LTD., Wuhancarbon, carbon-manganese, alloy 48Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 300SlabsA, B, D 100Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 100Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure Vessel

Xixia County,Nanyang City,

Huiche Town Industry Area,

Tel No: +86 377 697 65211 Fax No: +86 377 697 65333Email: [email protected]: www.elongcheng.comCertificate No: MD00/3969/0002/1 Expiry date 01/01/2018

Henan Province

304L, 304LN, 316L 12Austenitic Stainless SteelPlates from coilsOUTOKUMPU STAINLESS STEEL (CHINA) Co., Ltd. Shanghai Port

KunshanJiangsu Province

No. 288, Chenfeng RoadYushan Town

Tel No: +86 512 50120382 Fax No: +86 512 50120392

Certificate No: MD00/4422/0001/1 Expiry date: 26/01/2018

215300

Alloy 25EAF/LRF/VD/IngotSteelmakingPANGANG GROUP WuhanCarbon, Carbon-manganese 40alloy 25Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 40alloy 25ESR Ingotscarbon, carbon-manganese 300Barsalloy 390carbon, carbon-manganese, alloy 390StructuralBarscarbon, carbon-manganese, alloy 390Machinery

Jiangyou City,Sichuan Province,

JIANGYOU CHANGCHENG SPECIAL STEEL CO., LTD.,No.195, Jiangdong Road,

Tel No: +86 816 365 087 Fax No: +86 816 3650463Email [email protected]: http://www.cssc.com.cnCertificate No: MD00/4201/0002/1 Expiry date: 12/07/2019

621701

E 32Normal StrengthPlatesQINHUANGDAO SHOUGANG PLATE MILL CO.,LTD.

Dalian

A, B, D 35

AH27S, AH32, AH36, DH27S, DH32, DH36 32Higher Strength

360FG, 410FG, 460FG, 490FG, 510FG 32Boiler & Pressure Vessel

360AR, 410AR 35

No. 409 Jianshe StreetQinhuangdao City

Tel: +86 0335 3011421 3100 Fax: +86 0335 3014693email: [email protected]

Certificate #: MD00/2097/0009/1 Expiry date: 04/07/2018

Hebei Province

As at 10 April 2018 18Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

carbon, carbon-manganeseB.O.S. / Con CastSteelmakingQINHUANGDAO SHOUQIN METAL MATERIALSCO., LTD.

Dalian

carbon, carbon-manganese 400SlabsSemi-Finished

D 50Normal StrengthPlates

A, B 100

FH32, FH36, FH40 40Higher Strength

AH40, DH40, EH27S, EH32, EH36, EH40 60

AH36, DH27S, DH36 80

AH27S, AH32, DH32 100

360AR, 410AR 16Boiler & Pressure Vessel

360, 410 32

510FG 80

360FG, 410FG, 460FG, 490FG 100

Haigang DistrictQinhuangdao

Duzhuang

Tel +86 0335 6082696 Fax +86 010 6082690 Email: [email protected] web www.shouqin.com.cn

Certificate No: MD00/3136/0009/1 Expiry Date: 00/02/2020

All plate grades and thicknesses with through thickness properties, notations Z25 and Z35 may be added.

Hebei Province 066326

As belowB.O.S. / Con CastSteelmakingRIZHAO STEEL WIRE CO., LTD Qingdaocarbon, carbon-manganese 230SlabsSemi-FinishedA, B 25Normal StrengthHot Rolled CoilA, B 25Normal StrengthPlates from coils

No. 600, Yanhai Road, RizhaoShandongTel: +86 633 6188070 Fax: +86 633 6188155email. [email protected] web: www.rizhaosteel.comCertificate #: MD00/3843/0003/1 Expiry date: 05/10/2019

As belowE.A.F. / IngotSteelmakingSANXIN HEAVY INDUSTRY MACHINERY CO., LTD Jiangyincarbon, carbon-manganese, alloy 40Ingots (tonnes)Semi-Finished

Jiaze,Wujin, Changzhou,

Xia Xi North Road,

Tel No +86 519 83685579 Fax +86 519 83585579email: [email protected] web www.sanxinzg.comCertificate No MD00/4184/0002/1 Expiry Date 17/06/2019

Jiangsu, 213148

carbon, carbon-manganeseB.O.S. / Con CastSteelmakingSGIS SONGSHAN CO., LTD Guangzhoucarbon, carbon-manganese, alloy 270SlabsSemi-Finishedcarbon, carbon-manganese 425Bloomscarbon, carbon-manganese, alloy 170BilletsA, B, D, E 60Normal StrengthPlatesAH40, DH40, EH40 36Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

60

360AR, 410AR 20Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 60U3 150Chain Cable StockBars

Qujiang DistrictShaoguan City

Tel: +86 (0)751 878 5354 Fax: +86 (0)751 878 6066 email [email protected]

Certificate #: MD00/2175/0011/1 Expiry date: 21/11/2018

CEV is limited to a maximum of 0.45% for as rolled and nomalised higher strength steels but does not apply to TM steels

Guangdong 512123

As at 10 April 2018 19Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowB.O.S. / Con CastSteelmakingSHANDONG IRON & STEEL CO., Ltd. Qingdaocarbon, carbon-manganese 270SlabsSemi-FinishedE 50Normal StrengthPlatesA, B, D 60AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40, FH32,FH36, FH40

60Higher Strength

360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 60A, B 12Normal StrengthHot Rolled CoilAH27S, AH32, AH36 12Higher Strength

Jinan, 250101Shandong Province

JINAN COMPANY21, Gongye Bei Road

Tel +86 531 8886 6396 Fax +86 531 8898 8351 email: [email protected] web: www.jigang.com.cnCertificate #: MD00/0799/0014/1 Expiry date: 14/10/2019

As belowB.O.S. / Con CastSteelmakingSHANDONG IRON & STEEL CO., Ltd. QingdaoAs belowE.A.F. / Con CastU2, U3 160Chain Cable StockBars

Gang Cheng DistrictLaiwu City

LAIWU COMPANYNo.99 Fuqian Street

Tel: +86 634 7920316 Fax: +86 634 6820824email: [email protected] web: www.laigang.net

Bar over 130mm diameter is approved using EAF process route only.

Certificate No.: MD00/4389/0003/1 Expiry Date: 06/10/2020

As belowB.O.S. / Con CastSteelmakingSHANDONG SHOUGUANG JUNENG SPECIALSTEEL CO, LTD.

Qingdao

Carbon, Carbon-Manganese 310Rolled BilletsSemi-Finished

carbon, carbon-manganese 600Billets

carbon, carbon-manganese 130StructuralBars

carbon, carbon-manganese 130Machinery

U1 130Chain Cable Stock

U2, U3 160

No. 9 Tegang RoadShouguang, Shangdong Province

Tel: +86 532 5186159 Fax No. +86 532 5186789E-mail: [email protected] No: MD00/3260/0006/1 Expiry date: 21/09/2018

262711

austenitic stainless 130BarsSemi-FinishedSHANGHAI BAIHE WALSIN LIHWA Shanghai Port

No. 2402 Qingsong RoadBaihe Town, Qingpu District

SPECIALTY STEEL PRODUCTS Co., Ltd.

Tel: +86 21 59746686 Fax: +86 21 59746686

Certificate No: MD00/4450/0001/1 Expiry Date: 21/03/2018

Approval for austenitic grades covers types 304L, 316L, 321, 347.

Shanghai (201709)

A, B, D 20Normal StrengthSectionsSHANGHAI BAOSTEEL SECTION STEEL CO., LTD. Shanghai PortAH32, AH36 20Higher Strength

No. 3801, Huaxiang RoadShanghai

Tel No: +86 21 6221 1362 Fax No: +86 21 6221 9842Email [email protected] No. MD00/4686/002/1 Expiry date: 08/08/2020Approved for ERW welded section only

201107

As at 10 April 2018 20Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Carbon, Carbon-manganese, Alloy 200EAF/LRF/VD/IngotSteelmakingSHANGHAI ELECTRIC SHMP CASTING &FORGING CO., LTD.

Shanghai Port

Minhang District1800 Jiangchuan Road

Tel: +86 21 34098660 Mob: +86 1891 780 4183email [email protected] web: www.sshanghai-electric.com

Certificate #: MD00/1345/0003/1 Expiry date: 09/04/2020

200245

As belowE.A.F./A.O.D./Con CastSteelmakingSHANXI TAIGANG STAINLESS STEEL CO., LTD. DalianAs belowE.A.F/A.O.D/IngotAs below 8Ingots (tonnes)Semi-FinishedAs below 200SlabsAs below 230Billets304L, 316L 20Austenitic StainlessPlatesUNS S31803 40Duplex Stainless

Jiancaoping Street No. 2Taiyuan030003Taiyuan

Stainless Steel Hot Rolling Mill

Tel No: +86 351 3012029 Fax No: +86 351 3017893 Mob: 13503502921

All plate grades with specified through-thickness properties

Email: [email protected] Web: http://tgbx.tisco.com.cn Certificate No. MD00/3185/0009/1 Expiry date: 14/08/2020

As belowB.O.S. / Con CastSteelmakingSHANXI TAIGANG STAINLESS STEEL CO., LTD. DalianNormal strength, Higher Strength 200SlabsSemi-FinishedA, B, D 25Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 25Higher Strength360FG, 410FG 25Boiler & Pressure VesselA, B, D 25Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 25Higher Strength410 FG, 360 FG 25Boiler and Pressure Vessel

Jiancaoping Street No. 2Hot Strip Mill

Tel: +86 351 2132943 Fax: +86 351 2137664 Mobile: +86 135 0350 2921Email: [email protected] Web: http: //www.tisco.com.cn Slabs as semi finished products 2310mm nominal width and 12000mm nominal length to the above maximum thickness are approved for further processing forrolled products.Certificate #: MD00/3507/0004/1 Expiry date: 27/07/2020

A, B, D 40Normal StrengthPlatesSHANXI TAIGANG STAINLESS STEEL CO., LTD. DalianAH32, AH36, DH32, DH36 40Higher Strength304L, 316L, 304*, 316* 60Austenitic StainlessUNS S31803 40Duplex Stainless

Qiaodong Street No.3Linfen City

Linfen Heavy Plate Mill

Tel: +86 351 3017667 Fax: +86 351 3017893 Email: [email protected] Web: http:// www.tisco.com.cn Certificate No MD00/3688/0005/1 Expiry date 07/07/2015

Shanxi Province

Carbon, Carbon-manganese, Alloy 12EAF/LRF/VD/IngotSteelmakingSHANXI TAIGANG STAINLESS STEEL CO., LTD. Dalian

No.2 Jian Caoping Street,Taiyuan City,

Section Steel Plant,

Tel: +81 (0)351 2130108 Fax: +81 (0)351 2317595

E-mail: [email protected]

Website: tisco.com.cn

Certificate No. MD00/4240/0002/1 Expiry Date: 14/10/2019.

Shanxi Province,

As belowE.A.F. / IngotSteelmakingSHI GANG JING CHENG EQUIPMENTDEVELOPMENT

Dalian

carbon, carbon-manganese, alloy 132Ingots (tonnes)Semi-Finished

As at 10 April 2018 21Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

No. 1 Xinlian Street,Yingkou,

AND MANUFACTURING CO., LTD.

Tel: +86 0417 3257800 Fax: +86 0417 3257905email: [email protected] web: http://www.cyedm.com.cnCertificate #: MD00/4234/0004/1 Expiry date: 08/10/2019

Liaoning Province,

carbon, carbon-manganeseB.O.S. / Con CastSteelmakingSHIJIAZHUANG I & S CO., LTD. Daliancarbon, carbon-manganese 150StructuralBarscarbon, carbon-manganese 150MachineryU1, U2, U3 150Chain Cable Stock

Shijiazhuang CityHebei Province

No. 363 Heping E Road

Tel: +86 (0)311 869 12562 Fax: +86 (0)311 869 13368Email: [email protected] #: MD00/3315/0004/1 Expiry date: 05/02/2019

As belowB.O.S. / Con CastSteelmakingSHOUGANG JINGTANG UNITED IRON & STEELCO., LTD.

Qingdao

carbon, carbon-manganese 250SlabsSemi-Finished

A, B, D 18Normal StrengthHot Rolled Coil

AH32, AH36, DH32, DH36 18Higher Strength

A, B, D 18Normal StrengthPlates from coils

AH32, DH32, AH36, DH36 18Higher Strength

Caofeidian Industrial Zone, Tangshan

Tel: +86 315 8872636 Fax: +86 315 8872606 email: [email protected] web: www.sgjsteel.com

Certificate #: MD00/3820/0003/1 Expiry date: 19/11/2019

Post Code: 063200

As belowB.O.S. / Con CastSteelmakingSHOUGANG QIAN'AN IRON & STEEL COMPANY Daliancarbon, carbon-manganese, alloy 230SlabsSemi-FinishedA, B, D 18Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 18Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 18Boiler & Pressure VesselA, B, D 18Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 18Higher Strength

West Industrial DistrictQian'an City

No. 025, Zhao'an Road

Tel: +86 315 7703232 Fax: +86 315 7703136 web http://www.sggf.com.cn

Certificate #: MD00/3488/0005/1 Expiry date: 07/07/2020

Hebei, 064404

Carbon, Carbon-manganese, Alloy 8EAF/LRF/VD/IngotSteelmakingSICHUAN LIUHE FORGING CO., LTD. Wuhan

Baolun Road(W), Henan Industrial ParkJiangyou City

Tel No: +86 0816 3456788 Fax No: +86 0816 3521398Email: bk.liwei'@gmail.comCertificate No: MD00/4176/0002/1 Expiry date 08/06/2019

Sichuan Province

A, B, D, E 20Normal StrengthSectionsSUQIAN NANJING IRON & STEEL NanjingAH32, AH36, AH40, DH32, DH36, DH40, EH32,EH36

20Higher Strength

No.89 Jingshan Road,Suyu District,

JINXIN STEEL ROLLING Co., Ltd.

Tel; +86 527 844 53907 Fax: +86 527 844 80094 Mob: +86 (0)152 9832 5588 email: [email protected]

Certificate: MD00/3741/0007/1 Expiry date: 15/12/2020

Suqian City, Jiangsu,

As belowE.A.F. / Con CastSteelmakingSUZHOU SUXIN SPECIAL STEEL CO., LTD. Shanghai PortU1, U2, U3 120Chain Cable StockBars

Huashan, Tong An, SuzhouJiangsu

Tel: +86 0512 8887 8163 Fax: +86 0512 88877273email: [email protected] web: www.sugang.com.cn

Certificate #: MD00/3492/0003/1 Expiry date: 13/07/2017

Post Code: 215151

As at 10 April 2018 22Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

carbon, carbon-manganese 186Ingots (tonnes)Semi-FinishedTAI YUAN HEAVY INDUSTRY CO. LTD. Wuhan

No.53, Yuhe Street,Wanbailin District, Taiyuan City,

Tel +86 351 636 2835 Fax: +86 351 636 1424

E-mail: [email protected].

Website: www.tyhi.com.cn

Certificate #: MD00/3412/0005/1 Expiry date: 30/09/2019

Shanxi Province, 030024,

As belowB.O.S. / Con CastSteelmakingTANGSHAN HEAVY PLATE CO., LTD. Qingdaocarbon, carbon-manganese 250SlabsSemi-FinishedA, B, D 38Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 38Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 38Boiler & Pressure Vessel

Leting County,Tangshan City,

Lingang Industrial Park

Tel Nos: +86 315 4958145, +86 315 4958135 Fax No: +86 315 4959153Email [email protected]@163.com (enquiries), [email protected] (orders)

Certificate #: MD00/3475/0005/1 Expiry date: 30/05/2020

Hebei

A, B 24Normal StrengthSectionsTANGSHAN SHENGCAI STEEL CO., LTD. DalianAH32, AH36 24Higher Strength

Angezhuang Town,Luannan County, Tangshan City,

South of Xinghonglin Village

Tel No: +86 315 245 0855 Fax No: +86 315 445 1116email [email protected] web: [email protected]

Certificate No: MD00/4131/0003/1 Expiry Date 18/03/2019

Hebei Province

As belowB.O.S. / Con CastSteelmakingTANGSHAN YANSHAN IRON & STEEL CO., LTD. DalianNormal strength, Higher Strength 250SlabsSemi-FinishedNormal Strength 150Billets

The West Side of Qianan Railway StationQianan City

Tel: +86 315 7769 566 Fax: +86 315 7769 566E-mail: [email protected] nominal maximum width 150mm x 12,000mm nominal maximum length to the above maximum thickness supplied in the As Cast condition; slabsnominal maximum width 1,800mm x 12,000mm nominal maximum length to the above maximum thickness supplied in the As Cast condition; are approved forfurther processing for rolled products in the detailed strength levels.Certificate Number: MD00/3648/0005/1 Expiry: 08/06/2018

Hebei Province (064403)

As belowB.O.S. / Con CastSteelmakingTIANJIN IRON AND STEEL GROUP CO. LTD. Qingdaocarbon, carbon-manganese, alloy 250SlabsSemi-FinishedA, B, D 38Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 50Higher Strength

Dongli DistrictTianjin

398 Jintang Road

Tel:+86 22 24706052 Fax: +86 22 24706052 Email: [email protected]: www.tgsteel.comCertificate #: MD00/3485/0005/1 Expiry date: 30/06/2020

carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingTIANJIN PIPE (GROUP) CORPORATION Daliancarbon, carbon-manganese, alloy 400BloomsSemi-Finished

No 396, Jintang Road

Tel No: +86 22 2480 2296 Fax no: +86 22480 1291

Email [email protected]

Web: www.tpco.com

Certificate No MD00/3361/0005/1 Expiry Date 28/07/2019

300301

carbon, carbon-manganese 90E.A.F. / IngotSteelmakingTIANJIN TIANZHONG GIANT HEAVY INDUSTRYCO., LTD.

Qingdao

As at 10 April 2018 23Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Xiditou TownBeichen District

No. 609, Jinyu Road

Tel:+86 (0)22 86885730 Fax: +86(0)22 8688 5673emsil: [email protected] web: www.jiangtian.cnCertificate No: MD00/4094/0003/1 Expiry date: 24/11/2018

Tianjin

A, B 15Normal StrengthSectionsTIANJIN YONGHENG ENTERPRISE CO., LTD. DalianAH32, AH36 15Higher Strength

No. 5, Gangtuan West RoadDaqiu Town, Jinghai County

Tel:+86 (0)2228899180 Fax: +86(0)2228899185 Email:[email protected] Web:http://www.tjyhsy.comCertificate #: MD00/3953/0002/1 Expiry date: 24/09/2017

Tianjin, 301606

alloy 160E.A.F. / IngotSteelmakingTONGYU HEAVY INDUSTRY Co., Ltd Qingdaocarbon, carbon-manganese 200alloy 160Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 200

Dezhou City,Shandong Province,

National High-Tech Industry Area,Yucheng City,

Tel: +86 534 7520690 Fax: +86534 7521470Certificate No. MD00/3998/0003/1 Expiry date: 28/02/2018

As belowB.O.S. / Con CastSteelmakingWISCO WuhanAs below 250SlabsSemi-FinishedA, B, D, E 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50A, B, D 25Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 25Higher Strength360, 410 12Boiler & Pressure VesselA, B, D 25Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 25Higher Strength360, 410 12Boiler and Pressure Vessel

QingshanWuhan

Wuhan Iron and Steel Co., Ltd.Changqian

Tel: +86 27 8689 1629 Fax: +86 27 8689 2413

E-mail: [email protected]

web: www.wisco.com.cn

Certificate No: MD00/1683/0011/1 Expiry date: 19/11/2019

carbon, carbon-manganese, alloy 100Ingots (tonnes)Semi-FinishedWUHAN HEAVY INDUSTRY Wuhan

Qingshan District

CASTING AND FORGING CO., LTD.1 Wudong Street

Tel No:+86 027 6886 1813 Fax No: +86 027 6886 1810 Mob :+86 13720291417Email [email protected] www.whzg.com.cnCertificate No: MD00/1681/0003/1 Expiry date: 02/04/2020

Hubei

As belowB.O.S. / Con CastSteelmakingWUHAN IRON & STEEL GROUP WuhanAs below, Normal strength, Higher Strength 300SlabsSemi-FinishedA, B, D, E 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36 90Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 90Boiler & Pressure Vessel

No. 215 Wuchang DadaoEzhou City

ECHENG IRON & STEEL CO., LTD.

Tel: +86 711 3233225 Fax: +86 711 3233225 Email: [email protected] #: MD00/3931/0005/1 Expiry date: 01/07/2017

Z25 ad Z35 through thickness properties for plates of approved grades in the TM+Acc and Normalized conditio

Hubei Province, 436002

As at 10 April 2018 24Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowE.A.F. / IngotSteelmakingWUHAN ZHONGYE MACHINERY WHOLE SETEQUIPMENT

Wuhan

carbon, carbon-manganese, alloy 18Ingots (tonnes)Semi-Finished

Lingcheng Road No. 2Lingxiang Town, Daye City

Gourp Co., Ltd.DAYE BRANCH

Tel: +86 0714 370 2019 Fax: +86 0714 370 2196 Email : [email protected] #: MD00/4242/0001/1 Expiry date: 28/10/2016

Hubei Province

As belowE.A.F./Ingot/Con CastSteelmakingWUYANG IRON & STEEL COMPANY LTD. WuhanA, B, D, E 150Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

100Higher Strength

AH62, AH69, DH62, DH69, EH62, EH69, FH62,FH69

180

360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100

Henan ProvinceP.N: 462500

Wugang City

Tel: +86 375 811 1230 Fax: +86 375 811 4006E-mail: [email protected] with specified through thickness properties in listed grades of normal and higher strength steels.Certificate #: MD00/2044/0010/1 Expiry date: 25/03/2017

A, B, D, E 100Normal StrengthPlatesWUYANG IRON & STEEL COMPANY LTD. WuhanFH32, FH36, FH40 50Higher StrengthAH27S, AH32, AH36, AH40, AH42, AH46,AH50, AH55, AH62, AH69, DH27S, DH32,DH36, DH40, DH42, DH46, DH50, DH55, DH62,DH69, EH27S, EH32, EH36, EH40, EH42, EH46,EH50, EH55, EH62, EH69, FH42, FH46, FH50,FH55, FH62, FH69

100

360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure Vessel9Ni 40Ferritic Low Temperature

Wugang City,Henan Province,

Wuyang New Wide and Heavy Steel Plate Co Ltd

Tel No. +86 375 8111230 Fax No. +86 375 8114006 Email to: [email protected] with specified through thickness properties in listed grades of normal and higher strength steels 9NiCertificate No. MD00/3714/0006/1 Expiry Date 24/03/2020

PN 462500

Carbon, Carbon-manganese, AlloyEAF/LRF/VD/IngotSteelmakingXINING SPECIAL STEEL CO., LTD. Wuhancarbon, carbon-manganese, alloy 12Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 18ESR Ingotscarbon, carbon-manganese, alloy 250Semi-finished ProductsBars

No. 52 Chaidamu West RoadXining

Tel: 0086 0971 529 9294 Fax: 0086 0971 529 9407 Email: [email protected]: www.xntg.comCertificate #: MD00/3798/0003/1 Expiry date: 10/03/2019

Qinghai Province, 455004

See notesB.O.S. / Con CastSteelmakingXINYU IRON & STEEL CO. LTD. WuhanSee notesE.A.F. / Con Castcarbon, carbon-manganese 250SlabsSemi-FinishedA, B, D, E 80Normal StrengthPlatesFH27S, FH32, FH36, FH40 50Higher StrengthAH27S, AH40, DH27S, DH40, EH27S, EH40 60AH32, AH36, DH32, DH36, EH32, EH36 80360AR, 410AR 20Boiler & Pressure Vessel360, 410 60360FG, 410FG, 460FG, 490FG, 510FG 80A, B 14Normal StrengthSectionsAH27S, AH32, AH36 14Higher Strength

Xinyu CityJiangxi Province 338001

1 Yejin Road

Tel: 0791 6293506Email: [email protected]: www.xinsteel.com.cnAll grades with specified through thickness properties, designation to Z35 may be addedCertificate #: MD00/3093/0009/1 Expiry date: 10/06/2019

As at 10 April 2018 25Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Alloy 24EAF/LRF/VD/IngotSteelmakingXINYU XINLIANG SPECIAL STEEL CO., LTD. WuhanCarbon, Carbon-manganese 34alloy 24Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 34

Liangshan TownXinyu, 338013

Tel +86 (0)731 5865 2130 Fax +86 (0) 731 58653050 email: Certificate #: MD00/4596/0001/1 Expiry date: 12/07/2019

Approved for Z25 & Z35 grades.

Jiangxi

As belowB.O.S./Ingot/Con CastSteelmakingXISC - HUNAN VALIN XIANGTAN Wuhancarbon, carbon-manganese, alloy 300SlabsSemi-FinishedA, B, D, E 150Normal StrengthPlatesFH40 40Higher StrengthAH42, AH46, AH50, AH55, AH62, AH69, DH42,DH46, DH50, DH55, DH62, DH69, EH42, EH46,EH50, EH55, EH62, EH69*

50

FH27S, FH32, FH36 60AH40, DH40, EH40, EH47 80AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

150

360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselLTAH32, LTAH36, LTAH40, LTDH32, LTDH36,LTDH40, LTEH32, LTEH36, LTEH40, LTFH32,LTFH36, LTFH40

40Ferritic Low Temperature

Xiangtan City,Hunan Province,

IRON & STEEL CO., LTD.Yuetang District,

Tel +86 (0)731 5865 2130 Fax +86 (0) 731 58653050 email mailto:[email protected] web http://www.hnxg.com.cn

Certificate #: MD00/3258/0012/1 Expiry date: 07/08/2018

Approved for Z25 & Z35 grades.

* Mximum approved welding heat input in fabrication is 3.0 kJ/mm.

As belowE.A.F./V.O.D./Con CastSteelmakingYANTAI WALSIN STAINLESS STEEL CO., LTD. Qingdaoaustenitic stainless steel, duplex stainless steel,alloy steel

260Blooms/BilletsSemi-Finished

No. 2 Wuzhishan Road,Economic Technical Development Zone

Tel: +86 535 2166688 Fax: +86 535 2165008 Email:[email protected] #: MD00/3992/0002/1 Expiry date: 20/02/2018

Yantai City, shandong Province

austenitic stainless, duplex stainlessE.A.F. / IngotSteelmakingYONGXING SPECIAL STAINLESS STEEL CO LTD Shanghai Portaustenitic stainless, duplex stainless 11Ingots (tonnes)Semi-Finishedaustenitic stainless, duplex stainless 500Bars

Yangjiabu,Huzhou City,

Tel No. +86 572 2350629 Fax No: +86 572 2351517Email: wang [email protected] : www.yongxingbxg.cnCertificate No. MD00/3791/0003/1 Expiry date 05/06/2019

Zhejiang Province

As belowE.A.F. / Con CastSteelmakingZENITH STEEL GROUP CO., LTD. JiangyinU2, U3 130Chain Cable StockBars

No. 1 Zhongwu AvenueChangzhou City

Tel No. +86 519 88771301 Fax No: +86 519 88771301Email: [email protected] No. MD00/4273/0003/1 Expiry date 21/12/2019

Jiangsu Province

As belowE.A.F./V.O.D./IngotSteelmakingZHANGJIAGANG GUANGDA SPECIAL MATERIALCo., LTD

Jiangyin

carbon, carbon-manganese, alloy 10Ingots (tonnes)Semi-Finished

As at 10 April 2018 26Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Fenghuang Town,Zhangjiagang City, Jiangsu Province.

Anqing Village,

Tel: 00-86- 512- 5890270 Fax. No. 00- 86 - 512 - 58456318

E-mail: [email protected]

Website: gdjxdz.net

Certificate No: MD00/4690/0003/1 Expiry Date: 18.06.2020

As belowE.A.F./A.O.D./Con CastSteelmakingZHANGJIAGANG POHANG STAINLESS STEEL CO.,LTD.

Shanghai Port

As below 220SlabsSemi-Finished

304L, 316L, 321 80Austenitic StainlessPlates

304L, 316L, 321 16Austenitic StainlessHot Rolled Coil

UNS S31803 10Duplex Stainless

Daxin Riverside Road,Zhangjiagang City,

Plant No. 2

Tel: +86 512 58569312 Fax: +86 512 58569768-8023email: [email protected] web: www.zpss.comCertificate No: MD00/4734/0001/1 Expiry Date: 13/11/2020

Jiangsu Province,

As belowE.A.F./V.O.D./IngotSteelmakingZHEJIANG DALONG ALLOY STEEL CO., LTD. Shanghai PortCarbon, Carbon-manganese, Alloy 31EAF/LRF/VD/Ingotaustenitic stainless, martensitic stainless, duplexstainless

23Ingots (tonnes)Semi-Finished

carbon, carbon-manganese, alloy 31

Jiashan,Jiaxing,

Fenhu Industry Zone,Taozhuang Town,

Tel: +86 573 84899666 Fax: +86 573 84895280email: [email protected] web: www.zj-dalong.com

Zhejiang Province

austenitic stainless steelIF/AOD/Ingot/ConCastSteelmakingZHEJIANG TSINGSHAN IRON & STEEL CO.LTD. Zhoushanaustenitic stainless 3Ingots (tonnes)Semi-Finishedaustenitic stainless steel 240Blooms/Billetsaustenitic stainless 150Billets

Wenxi Town,Qingtian,

Xiaoshi Industry Zone

Tel No. 0086 578 6071301 Fax No. 0086 578 6062336

Email [email protected]

Web : www. zjqingshan.cn

Cert no. MD00/3673/0003/1 Expiry date: 24/08/2018

As belowA.O.D./Con CastSteelmakingZHENSHI GROUP EASTERN SPECIAL STEEL CO.,LTD.

Shanghai Port

304L, 304LN, 316L, 316LN, 317L, 317LN, 321 40Austenitic Stainless SteelPlates from coils

UNS S31803 40Duplex Stainless

304L, 316L, 317L, 321, 304LN, 316LN 16Austenitic StainlessCoil

UNS S31803 12Duplex Stainless

Xinfeng TownNanhu District, Jiaxing

Economic Development park (North)

Tel: +86 573 8398 8183 Fax: +86 573 8391 6907 Email to: [email protected]

Certificate #: MD00/4426/0003/1 Expiry date: 29/01/2021

Zhenjiang Province 314005

As belowB.O.S. / Con CastSteelmakingZHONGPU (HANDAN) IRON AND STEEL CO.,LTD.

Dalian

carbon, carbon-manganese 320SlabsSemi-Finished

A, B, D 38Normal StrengthPlates

AH27S, AH32, AH36, DH27S, DH32, DH36 38Higher Strength

As at 10 April 2018 27Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

China, People's Republic of360FG, 410FG, 460FG, 490FG, 510FG 38Boiler & Pressure VesselPlatesZHONGPU (HANDAN) IRON AND STEEL CO.,

LTD.Dalian

Yangyi Town,Wuan City,

No.1 & No.2 Steel Making Plant

Tel: +86 (0)310-5178955 Fax: +86 (0)310-5178928 email: [email protected] web: www.hbpygt.com

Certificate #: MD00/4034/0002/1 Expiry date: 26/04/2018

Hebei Province, 056305

carbon, carbon-manganese, alloy, stainless steel 6Ingots (tonnes)Semi-FinishedZHONGXING ENERGY EQUIPMENT CO., LTD NantongAs above 350Blooms/Billetscarbon, carbon-manganese, alloy 6EAF/LRF/VD/IngotSteel-makingaustenitic stainless 6IF/AOD/Ingot

SanchangHaimen City

No. 899, Zhonghua East Road

Tel: +86 513 82608033 Contact: Mr Liu Zi Ping Email to: [email protected] Web http://www.zxnyzb.com

Certificate #: MD00/4505/0002/1 Expiry date: 29/07/2018

Jiangsu Province

Croatia

As belowE.A.F. / Con CastSteelmakingABS SISAK d.o.o. Zagrebcarbon, carbon-manganese 410BilletsSemi-Finished

BRA�E KAVURI�A 12,44010 Sisak,Tel: +385 44 565467 email: [email protected]

Cert No. MD00/4210/0001/1 Expiry date: 25/07/2016

Czech Republic

carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingARCELORMITTAL OSTRAVA a.s. Praguecarbon, carbon-manganese, alloy 150SlabsSemi-Finishedcarbon, carbon-manganese, alloy 400BilletsA, B, D 14Normal StrengthSectionsA, B, D 60Normal StrengthBars

Vratimovská 689707 02 Ostrava-Kuncice

Approval for semi finished products covers con cast slabs to 150 x (750 to 1530) mm, con cast billets to 180 x 180mm and con cast rounds to 400mm diameter.

Tel: +420 595 684 213 email: [email protected] web: www.arcelormittal.com/ostrava

Certificate #: MD00/1123/0010/1 Expiry date: 10/12/2019

carbon, carbon-manganese 5Structural SectionsFabricated SectionsARCELORMITTAL TUBULAR PRODUCTS KARVINAA.S.

Prague

733 23 KarvinaRude armady 471

Tel: +420 596 391 465

E-mail: [email protected]

Website: www.jakl.cz

Longitudinal high frequency induction (HFI) welded tubes, pipes and hollowsCertificate #: MD00/4299/0002/1 Expiry date: 24/03/2020

As belowE.A.F. / IngotSteelmakingPILSEN STEEL s.r.o. Praguecarbon, carbon-manganese, alloy 200Ingots (tonnes)Semi-Finished

As at 10 April 2018 28Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

316 00 PlzenTylova 1/57

Tel: +420 378 134 225 Mob: +420 603 587 246email: [email protected] web: www.pilsensteel.cz Certificate # MD00/1383/0006/1 Expiry date: 23/03/2017

As belowB.O.S./Ingot/Con CastSteelmakingTRINECKE ZELEZARNY, a.s. PragueAs belowE.A.F./Ingot/Con Castcarbon, carbon-manganese 140SlabsSemi-Finishedcarbon, carbon-manganese, alloy 525BarsA 50Normal StrengthSectionscarbon, carbon-manganese, alloy 90MachineryBarsU1, U2 72Chain Cable Stock

Prumyslova 1000Stare Mesto

Tel: +420 558 534 016 Fax: +420 558 536 060 Email: mailto:[email protected] Web hppt://www.trz.czCertificate #: MD00/1562/0008/1 Inspection Due: 12/07/2019

739 61 Trinec

carbon, carbon-manganese, alloy 300StructuralBarsTRINECKE ZELEZARNY, a.s. Praguecarbon, carbon-manganese, alloy 300Machinery

vyrobni zavod:VZ - Sochorova valcovna

Prumyslova 1000, Stare Mesto739 61 Trinec

Tel No +420 558 536 065 Fax No. +420 558 534 926Email [email protected] www.trz.czMachinery grade bars with the maximum diameter of 300 mm produced from con-cast blooms may be accepted with a minimum rolling reduction of 3:1.Certificate #: MD00/2955/0007/1 Expiry date: 20/02/2018

272 01 Kladno Drin

B, D 40Normal StrengthSectionsTRINECKE ZELEZARNY, a.s. PragueA 50DH32, DH36 40Higher StrengthAH27S, AH32, AH36 50

VH - Univerzalni trat Bohumin,Bezrucova 300,

Tel: +42 (0) 558 534 016 or +42(0) 602 780 683 email: [email protected] web: www.trz.czThe approved sections are in the form of universal flats nominal widths 150 to 550mm to the maximum thicknesses shown above.

Parent Company: TRINECKE ZELEZARNY a.s., Prumyslova 1000, 739 70 Trinec-Stare Metso.Certificate ID No : MD00/2020.Certificate No. MD00/3056/0006/1 Expiry date: 11/02/2019

735 93 Bohumin

As belowE.A.F. / IngotSteelmakingVITKOVICE HEAVY MACHINERY a.s. Praguecarbon, carbon-manganese, alloy 130Ingots (tonnes)Semi-Finished

Ruska 2887/10170300 Ostrava-VitkoviceTel: +420 595 953 153 Mob: +420 602 535 608 email: [email protected] web: www.vitkovice.cz

Certificate #: MD00/2020/0007/1 Expiry date: 30/03/2020

A, B, D, E 100Normal StrengthPlatesVITKOVICE STEEL, a.s. PragueAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

100Higher Strength

360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselA, B, D, E 16Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

16Higher Strength

A, B, D, E 50Normal StrengthBarsAH27S, AH32, AH36, DH27S, DH32, DH36 50Higher Strength

709 00 Ostrava-Hulvaky,Czech Republic

Stramberska 2871/47,

Tel: +420 602 511 031 email: [email protected] web: www.vitkovicesteel.com

Certificate #: MD00/4380/0002/1 Expiry date: 05/08/2019

carbon, carbon-manganese, alloy 4E.A.F. / IngotSteelmakingValcovny trub Chomutov, a.s. Prague

Rokycanska 204,CZ-338 42 Hradek u Rokycan,

Works Hradek

Tel: +420 474 644096 Fax: +420 474 642 288 Email: [email protected]: www.steel-holding.czCertificate #: MD00/4063/0003/1 Expiry date: 04/08/2018

As at 10 April 2018 29Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingZDAS a.s. - Metallurgy Division Praguecarbon, carbon-manganese, alloy 12Ingots (tonnes)Semi-Finished

Strojirenska 675/659101 Zdar nad Sazavou

Metallurgical Plant

Tel: +420 566 643 054 Mobile: +42 602 795 859 Email: [email protected]:http://www.zdas.czCertificate #: MD00/1697/0006/1 Expiry date: 24/08/2020

Denmark

E 60Normal StrengthPlatesNLMK DANSTEEL A/S CopenhagenA, B, D 100AH40, DH40, EH27S, EH40, FH27S, FH32, FH36 60Higher StrengthEH32, EH36, EH36S 80AH27S, AH32, AH36, DH27S, DH32, DH36 100360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100

DK-3300 FrederiksværkHavnevej 33

Tel: +45 477 82647 Fax: +45 477 70302

E-mail: [email protected]

Web:http://www.dansteel.dk

All grades and thicknesses accepted with specified through thickness properties, Z25 and Z35 designations.

Certificate Number: MD00/0403/0009/1 Expiry: 07/01/2018

Egypt, Arab Republic of

A, B, D 100Normal StrengthPlatesABU ZAABAL ENGINEERING INDUSTRIES CairoAH27S 20Higher Strength

Inchas

Hot and Cold Rolling mill (AZE)Abu Zaabal

Tel: +20 24469 1224 Fax: +20 24469 2608 Email: [email protected] www.azr.comCertificate # MD00/3421/0005/1 Expiry date: 25/01/2020

As belowB.O.S. / Con CastSteelmakingEGYPTIAN IRON & STEEL CO. Port SaidA 50Normal StrengthPlatesA 8Normal StrengthHot Rolled Coil360FG, 410FG 8Boiler & Pressure VesselA 50Normal StrengthSections

HelwanCairo

El Tebbin

Tel: +202 5940593 Fax +202 5011608 [email protected] web www.hadisolb.com

Certificate #: MD00/0438/0009/1 Expiry date: 20/02/2019

As at 10 April 2018 30Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Finland

As belowE.A.F. / Con CastSteelmakingOUTOKUMPU STAINLESS OY Helsinki/Helsingfors

austenitic stainless 187SlabsSemi-Finished

304L, 316L, 321 12Austenitic StainlessPlates

304L, 316L, 321 12Austenitic StainlessHot Rolled Coil

304L, 316L, 321 6Austenitic StainlessCoil

Terastie 1,95490

Tel No: +358 40 7675371 Fax no:+358 16 452 350Email:[email protected] Web: http://www.outokumpu.comCertificate #: MD00/1165/0008/1 Expiry date: 29/03/2020

Tornio

As belowE.A.F. / Con CastSteelmakingOVAKO IMATRA OY AB Helsinki/Helsingfors

carbon, carbon-manganese, alloy 370BloomsSemi-Finished

Carbon, Carbon manganese, Alloy 180Rolled Bars

AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

180Higher StrengthBars

carbon, carbon-manganese, alloy 180Structural

alloy 180Machinery

carbon, carbon-manganese 200

Terästehtaantie 1FI-55100 IMATRATel: +358 5 680 21 Fax: +358 5 680 2211 Email: [email protected] Web:http://www.ovako.comSemi-finished products in carbon, carbon-manganese and alloy steel with fine grain (element combinations as stated), blooms to 370 mm section, to 6000mm longfor further processing to rolled productsMQS Approved - Approval No. MQS 020Certificate #: MD00/0751/0010/1 Expiry date: 05/01/2018

As belowB.O.S. / Con CastSteelmakingSSAB EUROPE OY Helsinki/Helsingfors

A, B, D, E 150Normal StrengthPlates

FH27S, FH32, FH36 40Higher Strength

AH40, DH40, DH42, EH40, EH42 80

AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

150

360AR, 410AR 40Boiler & Pressure Vessel

360, 410, 460, 490, 360FG, 410FG, 460FG, 490FG,510FG

100

LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

40Ferritic Low Temperature

A, B, D, E 15Normal StrengthHot Rolled Coil

AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

15Higher Strength

A, B, D, E 15Normal StrengthPlates from coils

AH27S, DH27S, AH32, DH32, AH36, DH36,EH27S, EH32, EH36

15Higher Strength

Rautaruukintie 155, PO Box 9392101 Raahe

Raahe Steel Works

Tel +358 20 5911 Mob +358 40 54 90257 Fax +358 20 5923527 Email: [email protected] Web: http://www.ruukki.com Specified through thickness properties for up to 150 mm thickness.

MQS Approved - Approval No. MQS 007Certificate #: MD00/1233/0012/1 Expiry date: 09/12/2019

As at 10 April 2018 31Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

France

Carbon, Carbon-manganese, AlloyEAF/LRF/VD/IngotSteelmakingAKERS FRANCE Lyoncarbon, carbon-manganese, alloy 70Ingots (tonnes)Semi-Finished

B.P. 1020057104 Thionville Cedex

USINE DE THIONVILLEChemin du Leidt

Tel: +33 6 79 27 94 41 e mail: mailto:[email protected] web: http://www.akersrolls.comCertificate #: MD00/3386/0003/1 Expiry date: 26/05/2017

304L, 316L, 304* 6Austenitic StainlessPlatesAPERAM Lyon304L, 316L, 304* 6Austenitic StainlessCoil

4 place des Forges71130 Gueugnon

Gueugnon Plant BP 1

Tel: +33 3 85 85 78 56 Fax: +33 3 85 85 14 12 Mob: +33 609320872Email: [email protected] Web: http://www.aperam.comCertificate #: MD00/1582/0007/1 Expiry Date: 08/03/2020

As belowE.A.F. / IngotSteelmakingAPERAM ALLOYS IMPHY LyonFe-36Ni* 8Fe-Ni alloysPlatesFe-36Ni* 1Fe-Ni alloysHot Rolled Coil

Avenue Jean Jaurès58160 IMPHYTel: +33 3 86 21 34 96 Email:mailto:[email protected] Web:http://www.aperam.com*Cold and hot rolled strip up to 8mm in INVAR/M93 grade (Fe-Ni36) accepted for approved applications; material greater than 1.5mm supplied in the AsRolled condition; materials 1.5mm or less are supplied in the solution annealed condition.Certificate Number: MD00/1870/0007/1 Expiry: 1/06/2018

As belowB.O.S. / Con CastSteelmakingARCELORMITTAL MarseilleNormal strength, Higher Strength 229SlabsSemi-FinishedA, B, D 16Normal StrengthHot Rolled CoilAH32, AH36, DH32, DH36, EH36 13Higher Strength460FG, 490FG, 510FG 13Boiler & Pressure Vessel360AR, 410AR 16

13776 Fos-Sur-MerCEDEX

Méditerranée Fos-sur-Mer

Tel: +33 (0) 442 47 30 68 Fax +33 (0) 4 4247 32 31Email: mailto: [email protected]: www.arcelormediterranee.comCertificate #: MD00/3803/003/1 Expiry date: 24/11/2018

As belowE.A.F./Ingot/Con CastSteelmakingASCO INDUSTRIES S.A.S Dunkerquecarbon, carbon-manganese, alloy 400Blooms/BilletsSemi-Finishedcarbon, carbon-manganese, alloy 310StructuralBarscarbon, carbon-manganese, alloy 310MachineryU3 105Chain Cable StockU1, U2 130

59941 DunkerqueCedex 2

Usine de DunesBP 41

Machinery grades up to 180 mm by continuous casting, 310 mm by ingotTel +33 32829 6052 Email to: [email protected] #: MD00/0117/0008/1 Expiry date: 11/09/2018

As belowE.A.F. / IngotSteelmakingASCO INDUSTRIES S.A.S Marseillecarbon, carbon-manganese, alloy 400BloomsSemi-Finishedcarbon, carbon-manganese, alloy 205Billetscarbon, carbon-manganese, alloy 325StructuralBars

13771 Fos-sur-Mer

Usine de Fos-sur-MerBP 30

Tel: +33 (0) 442 479251 Fax: +33 (0) 442 479276

Email : [email protected]

Website: ascometal.com

Certificate Number: MD00/0118/0007/1 Expiry: 02/09/2018

As BelowEAF/LMF/Con CastSteelmakingASCOVAL LyonCarbon, Carbon-manganese, Alloy 325As Cast Round SectionSemi-Finished

As at 10 April 2018 32Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Zone Industrielle N°4,CS30072,

Rue du Galibot

Tel: +33 03272 31890 Mob: +33 (6)801 24259email: [email protected]

Certificate No: MD00/4738/0001/1 Expiry Date: 19/12/2020

59880 Saint-Saulve

As belowE.A.F. / IngotSteelmakingAUBERT & DUVAL Lyoncarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless

42Ingots (tonnes)Semi-Finished

BP 14142704 FIRMINY CEDEX

Firminy Plant

Tel: +33 4 77 40 37 41 Email mailto: [email protected] Web: http://www.aubertduval.com

Ingots as semi-finished products to the above maximum weight; nominal; 1550/1730mm diameter x 2200mm; are approved for further processing for forgings.

Certificate Number: MD00/1770/0003/1 Expiry: 25/09/2018

As aboveE.A.F. / IngotSteelmakingAUBERT & DUVAL Lyonalloy, austenitic stainless steel, carbon, carbonmanganese

450Blooms/BilletsSemi-Finished

carbon, carbon-manganese, alloy, austeniticstainless

50StructuralBars

carbon, carbon-manganese, alloy, austeniticstainless

200Machinery

BP 163770 Les Ancizes

Aciéries des Ancizes

Tel: +33 4 73 67 31 27email: [email protected] www.aubertduval.comCertificate No: MD00/4537/0001/1 Expiry Date: 21/12/2018

As belowB.O.S. / Con CastSteelmakingCELSA FRANCE BilbaoNormal Strength, Higher Strength 160BilletsSemi-Finished

Rond-Point Claudius Magnin64340 BoucauTel: +33 05 59 64 41 00 Fax: +33 05 59 64 41 21 email: [email protected] web: hwww.celsafrance.com

Certificate Number: MD00/3539/0003/1 Expiry date: 10/11/2017

Billets as semi-finished products, nominal 160mm width and nominal 13300mm length to the above maximum thickness are approved for further processing forrolled products.

E 80Normal StrengthPlatesDILLINGER FRANCE DunkerqueA, B, D 100AH40, DH40, EH40, FH40 42Higher StrengthFH27S, FH32, FH36 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

150

360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselLTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

50Ferritic Low Temperature

Port 30323032 Rue du Comte Jean - CS 56317

Tel: +33 (0)3 28 29 39 22 Fax: +33 (0)3 28 29 69 12 Email: [email protected] Web: http://www.dillinger-france.comSpecified through thickness properties for all normal and higher strength grade plates notation - Z35 may be added.Certificate #: MD00/1818/0011/1 Expiry date: 07/06/2019

F-59379 Dunkerque Cedex 1

carbon, carbon-manganeseE.A.F. / IngotSteelmakingINDUSTEEL FRANCE LyonA 400Normal StrengthPlatesFH32, FH36 50Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 400360AR, 410AR 40Boiler & Pressure Vessel360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,9Ni

50Ferritic Low Temperature

As at 10 April 2018 33Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

BP 368 - Chateauneuf42803 RIVE DE GIER

ARCELOR MITTALSite de Chateauneuf

Tel: +33 477 752131 Fax: +33 4 77 75 20 03 Email: [email protected]

Including plates with specified through thickness properties.Certificate #: MD00/0351/0008/1 Expiry date: 18/04/2020

As belowE.A.F. / IngotSteelmakingINDUSTEEL FRANCE, site du Creusot Lyoncarbon, carbon-manganese, alloy, austeniticstainless

40Ingots (tonnes)Semi-Finished

71201 71201 LE CRUUSOT CEDEXLe Creusot Cedex

Porte du Breuil - BP 34

Tel No 33 3 8580 5575 Fax No. 33 3 8580 5211Email: [email protected]: www.industeel.infoCertificate number MD00/3227/0004/1 Expiry Date: 02/03/2018Ingots also in martensitic stainless steel up to 40 T for approved applications

A, B, D, E 150Normal StrengthPlatesINDUSTEEL FRANCE, site du Creusot LyonFH32, FH36 50Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 150360, 410, 360FG, 410FG, 460FG, 490FG 100Boiler & Pressure VesselLTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, 1.5Ni, 3.5Ni, 5Ni, 9Ni

50Ferritic Low Temperature

304L, 316L 50Austenitic Stainless

7120156 rue Clemenceau - BP19

Tel: +33 3 8580 5575 Fax: +33 3 8580 5211Email: mailto: [email protected] Web: http://www.industeel.infoPlates with specified through thickness properties.Certificate #: MD00/1822/0008/1 Expiry date: 26/02/2018

As belowB.O.S. / Con CastSteelmakingLAMINES MARCHANDS EUROPEENS Lyoncarbon, carbon-manganese 200BilletsSemi-FinishedA 13Normal StrengthSectionsA 30Normal StrengthBars

2, Rue Emile Zola59125 Trith St LégerTel +33 (0)3 2714 2270 Fax +33 (0)3 2714 2010 Email: mailto:[email protected] #: MD00/1395/0007/1 Expiry date: 19/10/2016

A, B, D, E 16Normal StrengthFabricated SectionsLORRAINE TUBES LyonAH32, AH36, DH32, DH36, EH32, EH36 14Higher Strength

54720 Lexy100, rue du Maréchal Foch

Tel No: +33 382 252 252 Fax No: +33 382 252 116Email: [email protected]: www.condesa.comCertificate No: MD00/4281/0001/ 1 Expiry Date: 17/01/2017

A, B, D, E 16Normal StrengthFabricated SectionsLORRAINE TUBES LyonAH32, AH36, DH32, DH36, EH32, EH36 16Higher Strength

57480 RettelRoute du Contez

Tel No: +33 382 252 225 Fax no: +33 382 252 116Email: [email protected]: www.condesa.com Certificate No: MD00/4282/0001/1 Expiry Date 17/01/2017

As belowE.A.F./A.O.D./Con CastSteelmakingUGITECH S.A. LyonAs below 205BilletsSemi-Finished304L, 316L, 321 32Austenitic StainlessSectionsUNS S31803 32Duplex Stainless304L, 316L, 321 130Austenitic StainlessBarsUNS S31803 130Duplex Stainlessaustenitic stainless, duplex stainless, martensiticstainless*

95Machinery

Avenue Paul Girod,73403 UGINE CedexTel: +33 4 79 89 32 92 Fax: +33 4 79 89 34 74 email: [email protected] web: www.ugitech.com

Certificate #: MD00/1583/0007/1 Expiry Date: 23/08/2017

As at 10 April 2018 34Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Germany

As belowB.O.S. / Con CastSteelmakingARCELORMITTAL BREMEN GmbH BremerhavenAs below 220SlabsSemi-FinishedA, B, D 20Normal StrengthHot Rolled Coil360, 410, 360FG, 410FG 20Boiler & Pressure Vessel

Carl-Benz- Straße 30D-28237 BremenTel +49 (0)421 648 1747 Fax +49 (0)412 648 49 3258 email: [email protected] web: www.arcelormittal.com/bremen

Certificate No. MD00/0857/0007/1 Expiry date: 16/10/2019

As belowB.O.S. / Con CastSteelmakingARCELORMITTAL HOCHFELD GmbH Hamburgcarbon, carbon-manganese, alloy 385BloomsSemi-Finishedcarbon, carbon-manganese, alloy 130Billets

Vohwinkelstraße 107D-47137 DuisburgTel 0049 (0) 203 606 66515 Fax 0049 (0) 203 606 66 362 email: [email protected] web www.arcelormittal.comCertificate Number: MD00/3631/0004/1 Expiry date: 23/07/2020

As belowB.O.S./Ingot/Con CastSteelmakingAktiengesellschaft der Dillinger Hüttenwerke HamburgA, B, D, E 170Normal StrengthPlatesFH32, FH36 50Higher StrengthAH40, DH40, EH40, EH46S, FH46S 100EH46, FH46 110AH62, AH69, DH62, DH69, EH62, EH69* 120AH36, DH36, EH36 150AH32, DH32, EH32 170AH36S, DH36S, EH36S* 220360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselLTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36, 5Ni

50Ferritic Low Temperature

HüttenwerkstrassePostfach 1580

All plates with specified through thickness properties.

* Approved for application with a maximum welding heat input of up to 2.3 kJ/mm.

Tel: +49 6381 474735 Fax: +49 6831 473224 email: [email protected] web:: www.dillinger.biz

Certificate No. MD00/0361/0019/1 Expiry date: 18/09/2020

D-66748 Dillingen / Saar

carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingBENTELER STEEL/TUBE GmbH Hamburgcarbon, carbon-manganese, alloy 215SlabsSemi-Finishedcarbon, carbon-manganese, alloy 310Blooms/Billets

Niederdarmer Straße 5D-49811 LingenTel: +49 591 80004 800 Fax: +49 591 80004 460 Email to: [email protected] Web: http://www.benteler.comCertificate No. MD00/1805/0007/1 Expiry date: 10/10/2017

Steelmaking and semi-finished slabs, blooms and billets intended for plates, forgings and tubes.Semi-finished products in carbon, carbon-manganese and alloy steel: slabs to 670mm wide, to 11,500mm long to 12.8 tonnes and blooms/billets of dimensions300mm x 230mm or 310mm round of maximum length 12,800mm

As belowE.A.F./Ingot/Con CastSteelmakingBGH EDELSTAHL FREITAL GmbH Hamburgalloy, austenitic stainless, martensitic stainless,duplex stainless

12Ingots (tonnes)Semi-Finished

As belowSlabsAs below 120Billetsalloy, austenitic stainless, duplex stainless steel,martenstic stainless*

160Semi-finished ProductsBars

alloy, austenitic stainless, duplex stainless,martensitic stainless*

165Machinery

Am Stahlwerk 1D-01705 FreitalTel: +49 (0)351 646 2408 Mob: +49 170 226 7303 email: mailto:[email protected] web: http://www.bgh.de

Certificate No. MD00/1973/0009/1 Expiry date: 05/08/2020

As at 10 April 2018 35Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowE.A.F./V.O.D./IngotSteelmakingBGH EDELSTAHL SIEGEN GmbH Hamburgmartensitic stainless 28Ingots (tonnes)Semi-Finishedaustenitic stainless, duplex stainless 35carbon, carbon-manganese, alloy 51

Industriestraße 9,D-57076

Tel No. +49 (0)271 701- 341 Fax No. +49 (0) 271 701376Email [email protected] www.bgh.deCertificate No MD00/3767/0006/1 Expiry date: 31/03/2019

Siegen

carbon, carbon-manganese, alloy, austeniticstainless

E.A.F. / IngotSteelmakingBUDERUS EDELSTAHL GmbH Hamburg

Martensitic stainless*E.A.F./V.O.D./Ingotcarbon, carbon-manganese, alloy 230Semi-finished ProductsBarscarbon, carbon-manganese, alloy 190Machinery

Buderusstraße 25D-35573 WetzlarTel: +49 (0)6441 374 2505 Fax: +49 (0)6441 374 2681 Email: [email protected] Web: http://www.buderus-steel.comCertificate No. MD00/0257/0012/1 Expiry date: 06/07/2020

As belowE.A.F. / Con CastSteelmakingDEUTSCHE EDELSTAHLWERKE HamburgAs belowE.A.F. / Ingotcarbon, carbon-manganese, alloy, austeniticstainless

80StructuralBars

carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless, martensitic stainless*

80Machinery

Obere KaiserstraßeD-57078 Siegen

SPECIALTY STEEL GmbH & Co. KGWorks Siegen

Tel: +49 (0)271 808 26 94 Fax: +49 (0)271 808 25 01 Email: mailto:[email protected] Web: http://www.dew-stahl.comCertificate No. MD00/0901/0009/1 Expiry date: 11/07/2017

As belowE.A.F. / Con CastSteelmakingDEUTSCHE EDELSTAHLWERKE HamburgAs belowE.A.F. / Ingotcarbon, carbon-manganese, alloy, stainless steel 66Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy, austeniticstainless

250Semi-finished ProductsBars

alloy, austenitic stainless 250Structuralalloy, austenitic stainless, duplex stainless,martensitic stainless*

250Machinery

Auestraße 4D-58452 Witten

SPECIALTY STEEL GmbH & Co. KGWorks Witten

Tel: +49 (0) 2302 292 437 Fax: +49 (0) 2302 294 008email: [email protected] web:www.dew-stahl.comCertificate No. MD00/2075/0013/1 Expiry date: 19/01/2019

As belowE.A.F./Ingot/Con CastSteelmakingGEORGSMARIENHÜTTE GmbH Hamburgcarbon, carbon-manganese, alloy 44Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 240BloomsA, B, D, E 180Normal StrengthBarsAH32, AH36, DH32, DH36, EH32 180Higher Strengthalloy 270Structuralcarbon, carbon-manganese 280U1, U2, U3, R3 155Chain Cable Stock

D-49124 GeorgsmarienhütteNeue Hüttenstraße 1

Tel: +49 5401 394657 Fax: +49 (0)5401 39 4598 Email: [email protected] Web: http://www.gmh.deCertificate No. MD00/0596/0008/1 Expiry date: 01/10/2019

As belowE.A.F. / Con CastSteelmakingH.E.S. HENNIGSDORFER ELEKTROSTAHLWERKEGmbH

Hamburg

carbon, carbon-manganese, alloy 100StructuralBars

carbon, carbon-manganese, alloy 50Machinery

U1, U2 73Chain Cable Stock

Wolfgang-Küntscher-Straße 18D-16761 HennigsdorfTel: +49 (0)3302 806-728 Fax: +49 (0)3302 806-724email: [email protected] web: www.rivagroup.com

Certificate No. MD00/0665/0009/1 Expiry date: 29/06/2020

As at 10 April 2018 36Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

A 50Normal StrengthSectionsHOESCH SCHWERTER PROFILE GmbH Hamburg

Eisenindustriestraße 1D-58239 SchwerteTel: +49 (0)2304 106-340 Fax: +49 (0)2304 106-590 Email: [email protected] Web: http://www.hoesch-profile.deCertificate No. MD00/0682/0007/1 Expiry date: 07/01/2018

carbon, carbon-manganese, alloy, High-nickelsteel (for low temperature service)

B.O.S. / Con CastSteelmakingHüttenwerke Krupp Mannesmann GmbH Hamburg

carbon, carbon-manganese, alloy, high-nickelsteel (for low temperature service)

260SlabsSemi-Finished

carbon, carbon-manganese, alloy 406Blooms/Billets

Ehinger Strasse 200D-47259 Duisburg-Huckingen

Huckingen Works

Tel: +49 (0)203 999 2633 Fax: +49 (0)203 999 4430

email: [email protected] web: www.hkm.de

Certificate No. MD00/0730/0009/1 Expiry Date: 05/02/2021

B, D, E 85Normal StrengthPlatesILSENBURGER GROBBLECH GmbH HamburgA 150AH40, DH40, EH40, FH40 100Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36

120

360AR, 410AR, 460AR 40Boiler & Pressure Vessel360, 410, 460, 490, 360FG, 410FG, 460FG, 490FG,510FG

100

LTAH40, LTDH40, LTEH40, 1.5Ni, 3.5Ni, 5Ni,9Ni

50Ferritic Low Temperature

LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

120

316L 80Austenitic Stainless

Veckenstedter WegD-38871 IlsenburgAll plates with specified through thickness properties.

Tel: +49 39452/85 9904 Fax: +49 39452/85 5733

E-mail: [email protected]

Web: www.ilsenburger-Grobblech.de

Materials Qaulity Scheme Approved. Approval No: 057

Certificate No. MD00/1654/0014/1 Expiry date: 22/02/2020

As belowE.A.F. / Con CastSteelmakingLech-Stahlwerke GmbH HamburgAs below 240Blooms/BilletsSemi-FinishedA, B 100Normal StrengthBarscarbon, carbon-manganese, alloy 90Machinery

Industriestrasse 1D-86405 MeitingenTel: +49 (0) 8271/82-325 Fax: +49 (0) 8271/82-405 Email:mailto:[email protected] Web: http://www.lech-stahlwerke.deCertificate No. MD00/0921/0007/1 Expiry date: 01/11/2018

A 12Normal StrengthSectionsMANNSTAEDT GmbH DortmundAH32, AH36, DH32, DH36 12Higher Strength

Mendener Str. 5153840 TroisdorfEmail: [email protected] Web: www.mannstaedt.deTel: +49 2241 842328 Fax: +49 2241 3328 Mobile: +49 176 12998066

Certificate: MD00/4700/0001/1 Expiry Date: 30/08/2020

As belowE.A.F. / Con CastSteelmakingPEINER TRÄGER GMBH HamburgA, B, D, E 40Normal StrengthSectionsAH32, AH36, DH32, DH36, EH32, EH36 40Higher Strength

D-31226 PeineGerhard-Lucas-Meyer Str. 10

Tel: +49 5171 91 9543 Fax: +49 5171 91 9373 email: [email protected] web: www.peiner-traeger.deCertificate No. MD00/3075/0006/1 Expiry date: 13/05/2019

As at 10 April 2018 37Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

A, B, D, E 250Normal StrengthPlatesREINER BRACH GmbH & Co. KG BremerhavenAH32, AH36, DH32, DH36, EH32, EH36 120Higher StrengthAH27S, DH27S, EH27S 250460FG, 490FG, 510FG 120Boiler & Pressure Vessel360FG, 410FG 150

Wilhelm-Karmann-Straße 5D-28237 BremenTel: +49 421 985 08-140 Fax: +49 421 985 08-149 Email: [email protected] Web:http://www.brach.deCertificate No. MD00/2631/0007/1 Expiry date: 31/12/2017

carbon, carbon-manganese 43Ingots (tonnes)Semi-FinishedREINER BRACH GmbH & Co. KG Bremerhaven

D-28237 BremenWilhelm-Karmann-Straße 5

Tel No +49 3364 37 81 54 Fax No +49 3364 37 81 55Email: [email protected]: www.brach.deCertificate No. MD00/4032/0004/1 Expiry Date 31/12/2017

Carbon, Carbon-manganese 200EAF/LRF/VD/IngotSteelmakingSAARSCHMIEDE GmbH FREIFORMSCHMIEDE Hamburg

Bismarckstraße 57-59D-66330 VölklingenTel:+49 (0)6898 10 2215 Fax:+49(0)6898 10 5 2215 email: [email protected] web: www.saarschmiede.com

Certificate No. MD00/2017/0003/1 Expiry date: 12/05/2020

A 40Normal StrengthBarsSAARSTAHL AG HamburgU1, U2, U3 40Chain Cable Stock

D-66511 NeunkirchenWorks Neunkirchen

Tel: +49 6898 104293 Fax: +49 6898 1054293 email: [email protected] web: www.saarstahl.com

Certificate No. MD00/1286/0008/1 Expiry date: 08/08/2020

As belowB.O.S. / Con CastSteelmakingSAARSTAHL AG HamburgNormal Strength 265Blooms/BilletsSemi-FinishedA 160Normal StrengthBarsU1, U2, U3 100Chain Cable Stock

Bismarckstrasse 57 - 59D-66330 Völklingen

Works Völklingen

Tel: +49 (0) 6898 104 293 Fax: +49 (0) 6898 105 4293 email: [email protected] web:www.saarstahl.com

Certificate Number: MD00/1931/0008/1 Expiry: 08/08/2020

As belowB.O.S. / Con CastSteelmakingSALZGITTER FLACHSTAHL GmbH Hamburgcarbon, carbon-manganese 350SlabsSemi-Finished

D-38239 Salzgitter,Eisenhüttenstrasse 99,Tel: +49 5341 21-3121 Fax: +49 5341 21-2510Email: [email protected]: www.salzgitter-flachstahl.de

Approved slab section sizes up to 350 x 2600mm.

Steel types carbon and carbon-manganese cover the supply of slabs for processing into normal strength, high strength, boiler and pressure vessel grades andferritic steels for low temperature service according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The finalprocessing mill is responsible for ordering steel which complies with their approved chemical composition and enables them to achieve the required mechanicalproperties.Certificate No. MD00/3990/0002/4 Expiry date: 14/02/2018

A, B, D, E 50Normal StrengthPlatesSALZGITTER MANNESMANN GROBBLECH GmbH HamburgAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

50Higher Strength

360AR, 410AR 40Boiler & Pressure Vessel360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 50304L, 316L 50Austenitic Stainless

Sandstrasse 140D-45473 Mülheim an der RuhrTel: +49 208 458 4878 Fax: +49 208 458 4511email: [email protected] web: www.smgb.de

Certificate No. MD00/1806/0008/1 Expiry date: 26/04/2020

As at 10 April 2018 38Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowE.A.F. / IngotSteelmakingSCHMIEDEWERKE GRÖDITZ GmbH Hamburgcarbon, carbon-manganese, alloy, austeniticstainless

84Ingots (tonnes)Semi-Finished

D-01609 GröditzRiesaer Straße 1

Tel: +49 35263 62970 Fax: +49 35263 62973 email: [email protected] web: www.stahl-groeditz.de

Certificate No. MD00/2880/0007/1 Expiry date: 10/04/2020

Including ESR ingot and the supply of liquid steel to Stahlguss Groditz GmbH.

As belowE.A.F./V.O.D./IngotSteelmakingSILBITZ GUSS GmbH Hamburgduplex stainless 7Ingots (tonnes)Semi-Finished

Dr. - Maruschky- Straße 2D-07613 Silbitz/ThüringenTel: +49 (0)3 6693 80-250 Fax: +49 (0)3 6693 80251 email: mailto: [email protected] web: www.silbitz-guss.de

Certificate #: MD00/1382/0003/1 Expiry date: 30/08/2020

Ingot approval covers duplex and superduplex grades.

alloy 40MachineryBarsSTAHLWERK ANNAHÜTTE MAX AICHER GMBH &CO. KG

Hamburg

D-83404 HammerauMax-Aicher-Allee 1+2

Tel: +49 (0) 8654 487 429 Fax: +49 (0) 8654 487 968Email: [email protected]: www.annahuette.comCertificate No.: MD00/4658/0001/1 Expiry date: 01/02/2020

carbon, carbon-manganese, alloyE.A.F./Ingot/Con CastSteelmakingSTAHLWERK BOUS GMBH Hamburgcarbon, carbon-manganese 60Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 500Billets

D-66359 Bous/SaarP/O Box 1243

Tel: +49 6834 81 292 Fax: +49 6834 81 586 email: [email protected] web www.stahlwerk-bous.deIngots up to 60 tonne and 2300 mm dia.Con cast billets approved up to 430 x 320mm section and 500mm diamater.

Certificate #: MD00/1249/0007/1 Expiry date: 19/08/2019

As belowE.A.F. / Con CastSteelmakingSTAHLWERK THÜRINGEN GMBH HamburgA, B 25Normal StrengthSectionsAH32, AH36, DH32, DH36 25Higher Strength

D-07333 UnterwellenbornKronacher Straße 6

Tel +49 3671 455006010 Fax +49 3671 45507710 Email: [email protected] Web http://www.stahlwerk-thueringen.deCertificate #: MD00/1424/0008/1 Expiry date: 19/11/2018

As belowE.A.F. / IngotSteelmakingSchmidt + Clemens GmbH +Co. KG Hamburgcarbon, carbon-manganese, alloy, austeniticstainless

50StructuralBars

D-51789 LindlarKaiserau 2

Tel No: +49 (0) 22 66 92 426 Fax No: +49 (0) 22 66 92 84 26email: [email protected] web: www.schmidt-clemens.deCertificate #: MD00/1319/0009/1 Expiry date: 09/10/2019

A, B, D, E 20Normal StrengthHot Rolled CoilTHYSSENKRUPP STEEL EUROPE AG HamburgAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20Boiler & Pressure VesselA, B, D, E 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 20Higher Strength410 FG, 460 FG, 360 FG, 360, 410, 490FG, 510FG 20Boiler and Pressure Vessel

Kaiser-Wilhelm-Straße 100D-47166 Duisburg

Works Bochum

Tel: +49 (0)203 52-45582 Fax: +49 (0)203 52-43568web: www.thyssenkrupp-steel-europe.com

Certificate No. MD00/0899/0009/1 Expiry date: 22/08/2020

As belowB.O.S. / Con CastSteelmakingTHYSSENKRUPP STEEL EUROPE AG HamburgNormal strength, Higher Strength 255SlabsSemi-FinishedA, B, D, E 20Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20Boiler & Pressure Vessel

As at 10 April 2018 39Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR OfficeWorks BeeckerwerthTel: +49 (0)203 52-23456 Fax: +49 (0)203 52-42100Web: www.thyssenkrupp-steel-europe.com

Certificate # MD00/1823/0009/1 Expiry date: 17/08/2020

As belowB.O.S. / Con CastSteelmakingTHYSSENKRUPP STEEL EUROPE AG HamburgA, B, D, E 20Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20Boiler & Pressure Vessel

Works BruckhausenTel: +49 (0)203 52-25591 Fax: +49 (0)203 52-25594 web: www.thyssenkrupp-steel-europe.com

Certificate No. MD00/1824/0009/1 Expiry date: 23/08/2020

A, B, D, E 150Normal StrengthPlatesTHYSSENKRUPP STEEL EUROPE AG HamburgFH27S, FH32, FH36 50Higher StrengthAH40, DH40, EH40 60AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

100

360AR, 410AR 40Boiler & Pressure Vessel360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36, 5Ni, 9Ni

50Ferritic Low Temperature

UNS S31803 35Duplex StainlessA, B, D, E 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36,EH27S, EH32, EH36

20Higher Strength

360 FG, 460 FG, 410 FG, 360, 410, 490FG, 510FG 20Boiler and Pressure VesselWorks Duisburg-SüdTel: +49 (0)203 52-45582 Fax: +49 (0)203 52-45568Web: www.thyssenkrupp-stahl.com

Certificate No. MD00/1825/0012/1 Expiry date: 17/08/2020

Specified through thickness properties on all normal and higher strength steel grade plates.

India

As belowA.O.D./Con CastSteelmakingAMBICA STEELS LIMITED Mumbaiaustenitic stainless, duplex Stainless 250BilletsSemi-Finished304L, 316L 125Austenitic StainlessBarsUNS S31803 125Duplex Stainless

Sahibabad-201010,Ghaziabad,

51/2, Site IV,Industrial Area,

Tel: +91 9811 045363 Fax: +91 4189366web: www.ambicasteels.com

Certificate No: MD00/4531/0001/1 Expiry Date: 01/12/2018

Approval for bars includes Bright Bars.

Approval covers IF/AOD steelmaking and concasting at the above address and also rolling and heat treatment activities at Plot No.-32, Site II, Loni RoadIndustrial Area, Mohan Nagar, Ghaziabad-201 007, Uttar Pradesh.

Uttar Pradesh

Carbon, Carbon-manganese, AlloyEAF/LRF/VD/IngotSteelmakingARCVAC FORGECAST LTD Chennaicarbon, carbon-manganese, alloy 10Ingots (tonnes)Semi-Finished

P.O: PanchgharaHooghly.

NH 2, Durgapur Expressway

Tel: + 91 33 2600 2176; Fax + 91 33 2659 8002Email: [email protected]: www. arcvacsteel.comCertificate No. MD00/3561/0004/1 Expiry date: 06/02/2018

West Bengal - 712 306

As belowE.A.F. / Con CastSteelmakingBHUSHAN POWER & STEEL LIMITED Chennaicarbon, carbon-manganese 200BilletsSemi-FinishedU1, U2, U3 90Chain Cable StockBars

Vill. Thelkoli, P.O. Lapanga,Tehsil - Rengoli,

Tel: +91 663 253 5000 / 256 2026-32 Fax: +91 663 256 2007 / 256 2011 Email: [email protected] Web: http://www.bpsl.netBillets as semi-finished products nominal 200mm maximum width x nominal 12000mm maximum length are approved for further processing for rolled products.Bars for Grades U1 and U2 accepted for end use in the normalised condition; bars for Grade U3 accepted for end use in the quenched and tempered condition.Certificate Number: MD00/4178/0002/1 Expiry: 09/06/2019

Distt. Sambalpur - 768 232,

As at 10 April 2018 40Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

austenitic stainless steel, as below 200A.O.D./Ingot/Con CastSteelmakingCHANDAN STEEL LIMITED Mumbai

GIDC Umbergaon Dist.Valsad

Plot 31, 32, 33B, 35, 36

Admin Office: Tel: +91 22 66290600, Fax: +91 22 66290633/34 Email to: [email protected]: Tel: +91 260 3089999, Fax: +91 260 2562287/2560103 Email to: [email protected]: www.chandansteel.net

Certificate No. MD00/4376/0001/1 Expiry date: 08/07/2017CCM Billets 100 to 200mm square of various sections cast from 4m to 9mm in lengthIngots of maximum weight 2500kg

Gujarat 396171

As belowE.A.F. / Con CastSteelmakingESSAR STEEL INDIA LTD. MumbaiNormal strength, Higher Strength 260SlabsSemi-FinishedA, B 20Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360FG, 410FG 20Boiler & Pressure VesselA, B 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 20Higher Strength

Hazira - 394270District Surat

Hot Strip Mill

Tel: +91 261 6683902/6683142 Email mailto: [email protected] Web http://www.essar.com Slabs as semi finished products nominal maximum width 2040mm x nominal maximum length 4900mm to the above maximum thickness are approved forfurther processing for rolled products.Certificate No. MD00/2091/0009/1 Expiry date: 05/06/2018

Gujarat

E 70Normal StrengthPlatesESSAR STEEL INDIA LTD. MumbaiA, B, D 100AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

70Higher Strength

360FG, 410FG 100Boiler & Pressure VesselPlate Mill DivisionTel: +91 261 668 3902 or 6739 Fax: +91 261 668 6739email [email protected] web www.essar.com

Certificate Number: MD00/3979/0005/1 Expiry: 16/01/2018

All plates are restricted to a maximum width of 4550mm.

carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingISMT LIMITED (STEEL PLANT) Mumbaicarbon, carbon-manganese, alloy 225BloomsSemi-Finishedcarbon, carbon-manganese, alloy 150Bars

Jejuri 412 303Purandar, Pune

Morgaon Road

Tel: +91-020-414 34100 Fax: +91-020-26630779 Email: [email protected] Web http://www.ismt.comCertificate number. MD00/3816/0003/1 Expiry date: 22/08/2019

Maharashtra

austenitic stainlessE.A.F./A.O.D./Con CastSteelmakingJINDAL STAINLESS (HISAR) LIMITED Mumbaiaustenitic stainlessE.A.F./V.O.D./Con CastAs below 200SlabsSemi-Finished304L, 316L, 317L, 321, 347 53Austenitic StainlessPlates

O.P. Jindal MargHisar Haryana State

Post Box No. 6

Tel: +91 98960 95018email: [email protected] web: www.jindalstainless.comCertificate No. MD00/3110/0005/1 Expiry date: 20/10/2019

India Pin 125 005

As BelowB.O.S./E.A.F./Con CastSteelmakingJINDAL STEEL & POWER LIMITED MumbaiA, B, D 80Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 80Higher Strength360AR, 410AR, 460AR, 360, 410, 460, 490, 360FG,410FG, 460FG, 490FG

80Boiler & Pressure Vessel

Post Box No.16Kharsia Road

Raigarh

Tel: +91 7762 227001 10 Fax: +91 7762 227021/22 Email to [email protected] Certificate No. MD00/3542/0004/1 Expiry date: 31/07/2020

Raigarh 496001 Chattisgarh

As at 10 April 2018 41Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowB.O.S. / Con CastSteelmakingJINDAL STEEL & POWER LIMITED MumbaiA, B, D 80Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 70Higher Strength460FG, 490FG, 510FG 70Boiler & Pressure Vessel360FG, 410FG 80

SH - 63, Village - NishaChendipada Road, Jindal Nagar

ORISSA

Tel: +91 9777445310 email: [email protected] web: www.jindalsteelpower.comCertificate No. MD00/4577/0001/1 Expiry date: 17/05/2019

Angul - 759111

As belowB.O.S. / Con CastSteelmakingJSW STEEL Ltd. MumbaiNormal strength, Higher Strength 220SlabsSemi-FinishedA, B, D, E 20Normal StrengthHot Rolled CoilAH32, AH36, DH32, DH36, EH32, EH36 20Higher StrengthA, B, D, E 20Normal StrengthPlates from coilsAH32, DH32, AH36, DH36, EH32, EH36 20Higher Strength

Vidyanagar,Bellary,

Vijayanagar Works,

Tel: +91 22 42863005 Fax: +91 22 42863000email: [email protected] web: www.jsw.in

Certificate No: MD00/4514/0001/1 Expiry Date: 04/10/2018

Karnataka,

As belowE.A.F./Ingot/Con CastSteelmakingKALYANI CARPENTER SPECIAL STEELS PRIVATELTD.

Mumbai

carbon, carbon-manganese, alloy 4Ingots (tonnes)Semi-Finished

carbon, carbon-manganese, alloy 320Blooms

carbon, carbon-manganese, alloy 250Bars

carbon, carbon-manganese, alloy 150StructuralBars

Pune 411 036Maharashtra

Mundhwa

Tel: +91 20 6621 5000 Fax: +91 20 2682 4483 Email: [email protected] Web: http://www.kalyanicarpenter.comApproved for ingots as semi-finished products to the above maximum weight nominal 540/700mm diameter x 1770mm long 540/700 and blooms to the abovemaximum thickness nominal 400mm wide x 10,000mm.Certificate Number: MD00/4447/0002/1 Expiry: 21/08/2018

As belowE.A.F./V.O.D./Con CastSteelmakingKALYANI STEELS Ltd. Mumbaicarbon, carbon-manganese 60BarsSemi-Finished

Ginigera, Taluk and District Koppal-KarnatakaHospet Road

Tel: +91 20 66215044 Fax: +91 20 26821124Email: [email protected]: http://www.kalyanisteels.comCertificate No.: MD00/4746/0001/1 Expiry date: 28/03/2021

As belowE.A.F. / IngotSteelmakingMAHINDRA SANYO SPECIAL STEEL PVT. LTD. Mumbaicarbon, carbon-manganese, alloy, austeniticstainless

13Ingots (tonnes)Semi-Finished

carbon, carbon-manganese, alloy, austeniticstainless steel

260Blooms/Billets

A 50Normal StrengthSectionsA 200Normal StrengthBars

KhopoliDist. Raigad

Khopoli WorksJagdish Nagar

Tel: +91(0)2192 260500 Fax: +91 (0)2192 262496 Mobile: +91 830882 8540 Email: [email protected] www.muscoindia.comCertificate No. MD00/0971/0009/1 Expiry date: 15/07/2018

Maharashtra 410 216

UNS S31803 120Duplex StainlessBarsPRECISION METALS Mumbai

As at 10 April 2018 42Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Atkargaon, Khopoli-410203,Taluka-Khalapur, Dist- Raigad,

Plot No. 253Takai-Adoshi Road,

Tel: +91 21 92 304800 Fax: +91 21 92 304915email: [email protected] web: www.venuswires.comCertificate No: MD00/4590/0001/1 Expiry Date: 04/07/2019

Approved for bright round bars to above maximum diameter.Scope of approval does not include steelamaking or rolling operations.

Maharashtra,

As belowB.O.S. / Con CastSteelmakingSTEEL AUTHORITY OF INDIA LTD. MumbaiNormal strength, Higher Strength 250SlabsSemi-FinishedA, B, D 75Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

50Higher Strength

460FG, 490FG, 510FG 50Boiler & Pressure Vessel360AR, 410AR, 360, 410 63360FG, 410FG 75

Bhilai 490 001Chhattisgarh

Bhilai Steel Plant

Tel +91 788-2222040

E-mail: klbalasubramanian@@sail-bhilaisteel.com

Website: sail-bhalaisteel.com

Certificate No. MD00/1433/0010/1 Expiry date: 26/04/2020

As belowB.O.S. / Con CastSteelmakingSTEEL AUTHORITY OF INDIA LTD. ChennaiA, B 52Normal StrengthPlates360, 410, 360FG, 410FG 35Boiler & Pressure Vessel360AR, 410AR 40

Rourkela 769 011Orissa

Rourkela Steel Plant

Tel: +91 (0) 661 244 7424 Fax +91 (0) 661 251 0183 email: [email protected] Web: http://www.sail.co.in Certificate Number: MD00/1434/0006/1 Expiry: 22/06/2016

As belowB.O.S. / Con CastSteelmakingTATA STEEL LIMITED ChennaiA 50Normal StrengthPlates360AR, 410AR 50Boiler & Pressure VesselA 12Normal StrengthHot Rolled Coil

Kolkata 700 07143 Chowringhee Road

Tel: +91 (33) 657 664 8310 Fax: +91 (33) 22887255/22881396 Email mailto: [email protected] Web http://www.tatasteel.comCertificate No. MD00/1489/0007/1 Expiry date: 14/02/2018

austenitic stainless steelIF/AOD/Ingot/ConCastSteelmakingVIRAJ PROFILES LIMITED (SMS, BAR ANDPROFILE DIVISION)

Mumbai

austenitic stainless steel 300Blooms/BilletsSemi-Finished

304L, 316L, 321 40Austenitic StainlessSections

austenitic stainless 200Semi-finished ProductsBars

GUT.No-25/1,25/2,26,27,31,33,34.VILLAGE-MAHAGAON, DIST-PALGHAR

G-2,23,76, MIDC, TARAPUR INDUSTRIAL AREA& SURVEY No 110, 111, 114/1, CD-116, 119 & 120,

Tel: +91 90444 1039 Fax: +91 2525 260159 Mob: +91 - 904 999 1347 E-mail: vijay.pillai.com

Website: www.viraj.com

Certificate Number: MD00/2935/0006/1 Expiry date: 06/12/2020

316Ti austenitic stainless steel accepted for approved applications.Billets and blooms as semi-finished products to the above maximum thickness, nominal 300mm wide x nominal 9000mm long are approved for furtherprocessing for forged products.

MAHARASHTRA - 401506

As at 10 April 2018 43Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Indonesia

B, D 25Normal StrengthPlatesPT. GUNAWAN DIANJAYA STEEL Tbk JakartaA 40AH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360AR, 410AR 25Boiler & Pressure Vessel

Tambak Sarioso,Asemrowo,

JL. Margomulyo No.29A,

Tel: +62 31 7490598 Fax: +62 31 7490581/7482109email: [email protected] web www.gunawansteel.comCertificate No. MD00/1882/0009/1 Expiry date: 14/12/2018

Surabaya 60184

A, B 50Normal StrengthPlatesPT. GUNUNG RAJA PAKSI JakartaAH36, AH40, DH36, DH40, EH36, EH40 50Higher Strength360AR, 410AR 40Boiler & Pressure VesselA, B 16Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 14Higher Strength360AR, 410AR 16Boiler & Pressure Vessel

JI. Imam Bonjol 4, Warung BongkokDesa Sukadanau, Clkarang Barat, Bekasi

Tel: +62 21 8900111 ext 3518 Fax: +62 21 8900333Email: mailto:[email protected] Web: http://www.grdsteel.comCertificate No. MD00/2749/0004/1 Expiry date: 14/11/2016

West Java, Indonesia

As belowB.O.S. / Con CastSteelmakingPT. KRAKATAU POSCO JakartaNormal strength, Higher Strength 230SlabsSemi-FinishedA, B, D, E 50Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

50Higher Strength

Kawasan Industri Krakatau,Cilegon,

Jalan Afrika No.2,

Tel: +62 (0)254 369700 Fax: +62(0)254 369799email: [email protected] web: www.krakatauposco.co.id

Approval includes Z grade plates.

Certificate No.: MD00/4377/0003/1 Expiry Date: 24/08/2020

Banten, 42443

As belowE.A.F. / Con CastSteelmakingPT. KRAKATAU STEEL (PERSERO) TBK. JakartaNormal strength 200SlabsSemi-FinishedA 25Normal StrengthHot Rolled CoilA 25Normal StrengthPlates from coils

Jl. Industri No. 5PO. Box 14

Tel: +62 (0) 254 317274 Fax: +62 (0) 254 372608 email: [email protected] web: www.krakatausteel.com

Certificate Number: MD00/1183/0009/1 Expiry: 01/02/2018

Plates and coils in the supply condition TM+Acc Fine Grain Al+Nb are restricted to the thickness range 16.0 to 25.0mm.Slabs as semi-finished products nominal maximum width 2000mm x and nominal maximum length 12000 mm to the above maximum thickness are approved forfurther processing for rolled products.

Cilegon 42435

As at 10 April 2018 44Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Italy

As belowE.A.F./Ingot/Con CastSteelmakingA. C. P. SRL Milancarbon, carbon-manganese, alloy 135Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 120Blooms/Billets

Loc. Motta Alta 14Cividate Al Piano

Tel: +39 363 97193/4 Fax: +39 363 976666 Email: [email protected] Web http://www.olifer.comCertificate No. MD00/1807/0009/1 Expiry date: 10/03/2018

Bergamo

As belowE.A.F./Ingot/Con CastSteelmakingA.B.S. Acciaierie Bertoli Safau S.p.A. VeniceCarbon, Carbon manganese, Alloy 370Rolled BarsSemi-FinishedCarbon, Carbon-manganese, Alloy 700As Cast Round SectionCarbon, Carbon-manganese, Alloy 420Rolled Square Barsalloy 240StructuralBarscarbon, carbon-manganese 270alloy 240Machinerycarbon, carbon-manganese 270U1, U2, U3 78Chain Cable StockR4 185

33050 Pozzuolo del Friuli (UD)Via Buttrio, 28

Tel: +39 0432 613211 E-mail: [email protected] Web: www.absacciai.itAddress for Orders: Rubiera Special Steel SpA, Via XXV Aprile, 64, 42013, Casalgrande (RE), Italy

The approval for mooring chain cable stock grade R4 bars is restricted to the supply of 185mm maximum diameter bars to Vicinay Sestao S.L. and to 166mmmaximum diameter bars to Vicinay Cadenas S.A., Deusto Factory, to the applicable Vicinay purchasing specification MPR4. The approval covers the ingot castmanufacturing route only.

Approval for normalised structural and machinery bars up to 270mm diameter is for both concast and ingot routes.

Certificate No. MD00/0019/0013/1 Expiry date: 13/06/2020

austenitic stainless, As belowE.A.F./A.O.D./Con CastSteelmakingACCIAI SPECIALI TERNI S.p.A. Veniceaustenitic stainlessE.A.F./V.O.D./Con Castaustenitic stainless 215SlabsSemi-Finished304L, 316L, 321 6Austenitic StainlessHot Rolled Coil

Viale B. Brin 218,I 05100 Terni,tel: +39 0744 4901 Fax: +39 0744 490904email: [email protected] web: www.acciaiterni.com

cert no: MD00/4414/0001/1 expiry date: 05/01/2018

Approval covers concast slabs to 215 x 1565 mm section size.

Approval includes proprietry 470 LI greade, accepted for approved applications only.

Approval includes 316 Ti and 309S grade to above thickness, accepted for approved applications only.

Approval includes above grades as cold rolled coil in solution treated condition to 3mm thickness.

As below, carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingACCIAIERIA FONDERIA CIVIDALE S.P.A. Triestecarbon, carbon-manganese, alloy 35Ingots (tonnes)Semi-Finished

Zona Industriale33043 Cividale del Friuli

Via delle Industrie No. 40

Tel +39 432 706911 Fax +39 432 706920 email: [email protected] web www.cividalespa.com

Certificate No. MD00/3149/0006/1 Expiry date: 02/04/2020

Steel types carbon, carbon-manganese and alloy cover the supply of ingots for processing into forgings according to the Society's Rules for the Manufacture,Testing and Certification of Materials, Chapter 5. The final processing mill is responsible for ordering steel which complies with their approved chemicalcomposition and enables them to achieve the required mechanical properties

(Udine)

As belowE.A.F./Ingot/Con CastSteelmakingACCIAIERIE VALBRUNA S.P.A. Venicecarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless

10Ingots (tonnes)Semi-Finished

carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless

220Billets

austenitic stainless, precipitation hardenedstainless*, martensitic stainless*

155MachineryBars

duplex stainless 205

As at 10 April 2018 45Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

36100 VicenzaViale Della Scienza, 25 z.i.

Tel: +39 0444 968211 Fax: +39 0444 968182 mail:[email protected] Web:http://www.acciaierie-valbruna.com* Accepted for approved applicationsApproval for Precipitation Hardened Stainless Machinery Bar is for Grade 17.4 PH, approval for Martensitic Stainless Machinery Bar is for Grade 431 and Grade1.4418 Quenched and Tempered.Duplex Stainless Steel bars are not approved for use in welded construction, and weld repair is not permitted.Approval of Con cast material is for the production of Austenitic Stainless Steels only.Ingots as semi finished products nominal maximum dimensions 600mm x 530mm x 2060mm to the above maximum weight Billets as semi finished products nominal maximum width 220mm x nominal maximum length 6500mm to the above maximum thickness Certificate No. MD00/0041/0008/1 Expiry date: 31/05/2020

As belowE.A.F./Ingot/Con CastSteelmakingACCIAIERIE VALBRUNA S.P.A. Veniceas belowA.O.D./Ingot/Con Castaustenitic stainless, duplex stainless,precipitation hardened stainless*, martensiticstainless*

73MachineryBars

Via A Volta 439100 Bolzano39100 Bolzano* Accepted for approved applicationsTel; +39 (0)471 924111 Fax: +39 (0)471 924355Email mailto:[email protected] Web: http//www.acciaierie-valbruna.itCertificate No. MD00/2994/0005/1 Expiry date: 25/06/2018

carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingACCIAIERIE VENETE S.p.A. Venicecarbon, carbon manganese, Alloy 280Blooms/BilletsSemi-FinishedCarbon, Carbon-manganese, Alloy 600As Cast Round Sectioncarbon, carbon-manganese, alloy 200Semi-finished ProductsBarscarbon, carbon-manganese, alloy 180Structuralcarbon, carbon-manganese, alloy 130Machinery

35020 Camin (Padova)

Camin WorksRiviera Francia, 9

Tel +39 (0)49 8282 820 Fax +39 (0)49 8282 666 email: [email protected] web: www.acciaierievenete.com

Approval does not cover bars with a diameter of less than 65mm.

Certificate No. MD00/0042/0007/1 Expiry date: 25/03/2018

As belowE.A.F. / Con CastSteelmakingAFV ACCIAIERIE BELTRAME S.p.A VeniceNormal strength, Higher Strength 220SlabsSemi-FinishedA, B, D, E 20Normal StrengthSectionsAH32, AH36, DH32, DH36 20Higher Strength

Viale della Scienza 81/A36100 VicenzaTel: +39 0444 967111 Fax: +39 0444 967282email: [email protected] web: www.grupobeltrame.com

A, B, D 22Normal StrengthFabricated SectionsARMANDO CIMOLAI CENTRO SERVIZI Srl VeniceAH32, AH36, DH32, DH36 22Higher Strength

Via Masieres, No.3233080 San Quirino (PN)Tel: +39 (0)434 919292 Fax: +39 (0)434 919266email: [email protected]

Certificate No. MD00/2620/0007/1 Expiry date: 29/11/2020

carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingASO SIDERURGICA S.p.A. UNIPERSONALE MilanAs belowE.A.F/A.O.D/Ingotaustenitic stainless 30Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 65

25035 OspitalettoBrescia

Via Seriola no. 122

Tel: +39 (0)30 6841011-(0)30 6841165 Fax: +39 (0)30 6841012

Email: [email protected] Web: http://www.asogroupsteel.com.

Certificate No. MD00/0020/0008/1 Expiry date: 13/04/2020

A 20Normal StrengthFabricated SectionsBAGLIETTO S.r.l. GenoaAH36, DH36, EH36 20Higher Strength

Novi Ligure (AL)Via Castelgazzo 11

Tel: +39 0143 318000 Fax: +39 0143 319252

Website: www.baglietto.it Certificate No. MD00/3910/0003/1 Expiry date: 14.05.2020

As at 10 April 2018 46Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowE.A.F. / Con CastSteelmakingCOGNE ACCIAI SPECIALI S.p.a MilanAs belowE.A.F. / Ingotaustenitic stainless, martensitic stainless, duplexstainless

14Ingots (tonnes)Semi-Finished

Martensitic Stainless Steel* 220Billetsaustenitic stainless, duplex stainless 270Martensitic Stainless Steel* 400Barsmartensitic stainless* 400StructuralBarsmartensitic stainless* 400Machinery

Via Paravera,1611100 AOSTATel No: +39 165 3021 Fax no: +39 165 302 423email: [email protected] web site: www.cogne.com

Steelmaking includes AOD / LF refining

* Accepted for approved applications.

Martensitic stainless bars up to 145 mm diameter produced by rolling from concast billet.Martensitic stainless bars up to 160 mm diameter produced by rolling from ingot.Martensitic stainless bars up to 400 mm diameter produced by forging from ingot.

Machinery bars from concast/rolling route approved up to 125mm.

Certificate No.MD00/3809/0003/1 Expiry date 12/07/2019

carbon, carbon-manganese, alloy, austeniticstainless, duplex

125IngotsESRFOMAS S.p.A. Milan

Via Martiri della Liberazione, 1723875 Osnago (LC)Tel No +39 3999811 Fax No +39 3958487email: [email protected] web: www.fomas.itCertificate No MD00/0475/0004/1 Expiry 08/01/2019

As belowB.O.S. / Con CastSteelmakingILVA SPA IN AMMINISTRAZIONESTRAORDINARIA

Venice

Normal strength, Higher Strength 303SlabsSemi-Finished

A, B, D, E 80Normal StrengthPlates

AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

80Higher Strength

A 10Normal StrengthHot Rolled Coil

AH27S, AH32, AH36 10Higher Strength

Via Appia KM 64874123 Taranto

Taranto Works

Tel: +39 02 307 00 775 Fax: +39 02 307 00 285 Email: [email protected] Web: http://www.rivagroup.comSpecified through thickness properties for grade D, E, AH, DH and EH notation Z35 may be addedCertificate No. MD00/2276/0007/1 Expiry date: 09/10/2018

carbon, carbon-manganeseE.A.F. / Con CastSteelmakingINDUSTRIE RIUNITE ODELESI I.R.O S.p.A Milancarbon, carbon-manganese 140BilletsSemi-Finished

12-25076 - Odolo (BS)Via Brescia 12,

Tel: 0365-826089, Fax No. 0365 - 860564

E-mail: [email protected]

Website: www.iro-spa.it

Certificate No. MD00/4589/0001/1 Expiry Date: 03/07/2019

carbon, carbon-manganese, alloy, austeniticstainless

E.A.F. / IngotSteelmakingLUCCHINI RS S.p.A. Milan

Via G. Paglia N.4524065 Lovere

Tel: +39 035 963520 Fax: +39 035 963488 Email: mailto: [email protected] Web: http://www.lucchiniRS.itCertificate No. MD00/0949/0008/1 Expiry date: 18/03/2018

Bergamo

A, B, D, E 60Normal StrengthPlatesMETINVEST TRAMETAL S.p.A. TriesteAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

60Higher Strength

360FG, 410FG, 460FG, 490FG, 510FG 60Boiler & Pressure Vessel

As at 10 April 2018 47Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Via Enrico Fermi, 4433058 San Giorgio di Nogaro (UD)Tel: +39 0432 629989 Fax: +39 0432 62985

E-mail: [email protected]

Website: www.trametal.metinvestholding.com

Certificate No. MD00/2004/0009/1 Expiry date: 31/07/2020

Approved for Z grade plates with specified through thickness properties when tested in accordance with Rules requirements.

Materials Quality Scheme Approved - Approval Scheme No. 061

As belowE.A.F. / IngotSteelmakingNLMK VERONA Venicecarbon, carbon-manganese, alloy 32Ingots (tonnes)Semi-Finished

Via A, Salieri, 22,37050 Vallese di Oppeano (Verona)Tel: +39 045 699 7900 Fax: +39 045 699 7901 email: [email protected] Web: http://www.eu.nlmk.com/verona/Round and Polygon ingots to nominal maximum dimensions of 1200mm diameter x 4750mm length, oblong ingots to nominal maximum dimensions 970mm x870mm x 2050mm.Certificate Number MD00/3985/0003/1 Expiry date: 30/01/2018

Carbon, Carbon-manganese, Alloy 40EAF/LRF/VD/IngotSteelmakingNUNKI STEEL SPA Venice

E.Fermi 33,33058 San Giorgio Di Nogaro (UD),Tel: 00 39 (0)431 623943 Fax: 00 39 (0) 431 623965Certificate No.:MD00/4087/0002/1 Expiry Date: 05/11/2018

carbon-manganese 35Structural SectionsFabricated SectionsOFFICINE ANTONIO MARINO S.R.L. Venice

90040 Isola delle Femmine (Palermo)Via delle Industrie, 13

Tel: +39 091 86 71681 Fax: +39 091 86 71686Certificate No.: MD00/4625/0001/1 Expiry Date: 26/10/2016

A, B, D, E 50Normal StrengthFabricated SectionsOFFICINE NORD EST S.r.l VeniceAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength

Via Ungaresca No.1233080 San Quirino (Pn)Tel: +39 (0)434 919091 Fax: +39 (0)434 918646 email: [email protected]

Certificate No. MD00/2626/0007/1 Expiry date: 06/12/2017

Approved welding process - SAWApproved weld type - Fillet weld only

A, B, D 10Normal StrengthSectionsOLIFER SRL MilanAH32, AH36, DH32, DH36 10Higher Strength

25076 Odolo (BS)Via G. Marconi 4

Tel +39 365 826088 Fax +39 365 860727 Email: mailto: [email protected] Web:http://www.olifer.com

Certificate No. MD00/4485/0001/1 Expiry date: 30/03/2018

A 25Normal StrengthFabricated SectionsPALESCANDOLO LAVORAZIONI SIDERURGICHESRL

Naples

AH32, AH36 25Higher Strength

DH36 30

Via Boscofangone, zone A.S.I., 80035 NolaTel. no. +39 0817340800; Fax. no.: +39 0817340454 Email: [email protected]; web: www.palescandolo.itCertificate No. MD00/3850/0003/1 Expiry date: 29/10/2019

As belowE.A.F./Ingot/Con CastSteelmakingRUBIERA SPECIAL STEEL S.p.A. Venicecarbon, carbon-manganese, alloy, NormalStrength, Higher Strength

100Ingots (tonnes)Semi-Finished

carbon, carbon-manganese, alloy, NormalStrength, Highrer Strength

180Bars

As at 10 April 2018 48Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

42013 Casalgrande (RE)Via 25 Aprile, 64

Tel: +39 0522 997232 Fax: +39 0522 840040 E-mail: [email protected] & [email protected]

Website: www.arss.it

Address for orders: Rubiera Special Steel S.p.A. , Via Adda, 23, 2305, Nuova Olonio di Dubino, Italy.

Ingots as semi finished products nominal maximum diameter 1935mm x nominal maximum height 5250mm to the above maximum weight in normal strengthand higher strength grades are approved for further processing for rolled products and in carbon, carbon-manganese & alloy grades are approved for furtherprocessing for forgings.Bars as semi finished products nominal maximum length 9500mm to the above maximum thickness in normal strength and higher strength grades are approvedfor further processing for rolled products and in carbon, carbon-manganese & alloy grades are approved for further processing for forgings.Certificate Number: MD00/0038/0008/1 Expiry: 06/03/2019

AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

30Higher StrengthSectionsSIDERVAL S.P.A. Milan

Via Chini Battista 6023018 Talamona (SO)Tel: +39 342 674152Email: mailto:[email protected] Web: http://www.siderval.itCertificate No. MD00/2857/0006/1 Expiry date: 14/01/2020

Japan

carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingAICHI STEEL CORPORATION Kobecarbon, carbon-manganese, austenitic stainlessE.A.F. / Ingotcarbon, carbon-manganese, alloy 480Blooms/BilletsSemi-Finishedcarbon, carbon-manganese, alloy 190BarsA 180Normal StrengthBars304L, 316L 180Austenitic Stainlesscarbon, carbon-manganese 190Structuralalloy, austenitic stainless 125Machinerycarbon, carbon-manganese 190U1, U2, U3 120Chain Cable Stock

Arao-machiTokai-shi

Chita Plant1, Wano-Wari

Tel: +81 52 603 9353 Fax: +81 52 603 9898 email: [email protected] web: www.aichi-steel.co.jp

Certificate No. MD00/0076/0009/1 Expiry date: 23/09/2018

Aichi-ken, 476-8666

304L, 316L 150Austenitic StainlessBarsAICHI STEEL CORPORATION Kobe

Kariya-shiAichi-ken

Kariya Plant3-6, Toyota-cho

Tel +81 566 21 9130 Fax +81 566 23 6925 email: [email protected] web www. aichi-steel.co.jpCertificate No. MD00/0078/0007/1 Expiry date: 22/09/2018

448-0848

As belowE.A.F. / Con CastSteelmakingCHUBU STEEL PLATE CO., LTD. KobeA, B 50Normal StrengthPlates360AR, 410AR 40Boiler & Pressure Vessel

Nakagawa-kuNagoya

5-1, Kousudori

Tel: +81 52 661 3818 Fax: +81 52 661 2265 Email: mailto:[email protected] Web http://www.chubukokan.co.jpCertificate No. MD00/0309/0008/1 Expiry date: 18/04/2020

As belowE.A.F. / IngotSteelmakingDAIDO STEEL CO., LTD. Kobecarbon, carbon-manganese 7Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 275Bloomscarbon, carbon-manganese 148Billetscarbon, carbon-manganese 270StructuralBars

39, Motohama-machiTokai-shi

Chita Plant

Tel: +81 562 33 3106 Fax: +81 562 33 6598 email: [email protected] web: www.daido.co.jp

Certificate No. MD00/0372/0007/1 Expiry date: 19/03/2020

Aichi-ken

As at 10 April 2018 49Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingDAIDO STEEL CO., LTD. Yokohama

Shibukawa-shiGunma 377-0007

Shibukawa Plant500, Ishihara

Tel: +81 279 25 2009 Fax: +81 279 25 2043 Email: mailto:[email protected] No. MD00/0375/0008/1 Expiry date: 25/11/2018

As belowE.A.F. / Con CastSteelmakingGODO STEEL LTD. Kobecarbon, carbon-manganese 490SlabsSemi-FinishedA 15Normal StrengthSectionsA 150Normal StrengthBarsU3 100Chain Cable StockU1, U2 150

Hyogo pref.

2946 Nakashima ShikamakuHimeji-city

Tel. +81 (0)79 234 9332 Fax +81(0)79 234 9538 Web: http://www.godo-steel.co.jpCertificate No. MD00/0606/0007/1 Expiry date: 05/08/2018

As belowE.A.F. / IngotSteelmakingHITACHI METALS, LTD. KobeA 150Normal StrengthBarsalloy, austenitic stainless 150Structural

Yasugi-shiShimane-ken

Yasugi Works2107-2, Yasugi-cho

Tel: +81 (0) 854 22 1908 Fax: +81 (0)854 23 0218 Email mailto:[email protected] Web http://www.hitachi-metals.co.jpCertificate No. MD00/0678/0007/1 Expiry date: 19/12/2018

As belowE.A.F. / Con CastSteelmakingJFE BARS & SHAPES CORPORATION KobeNormal Strength, Higher Strength 300BloomsSemi-FinishedNormal Strength, Higher Strength 150BilletsB, D, E 25Normal StrengthSectionsA 32EH32, EH36 25Higher StrengthAH32, AH36, DH32, DH36 32

1280, Hosoe,Shikama-ku, Himeji-City,

Himeji Works

Tel +81 (0)792 35 6376 Fax +81 (0)792 35 2048 email: mailto:[email protected] Web: http://www.jfe-bs.co.jpThe scope of approval for semi-finished products includes for; billets nominal maximum width 150mm x nominal maximum length 8600mm; blooms nominalmaximum widths 220mm x nominal maximum length 10.000mm; approved for further processing for rolled products.Certificate Number: MD00/1535/0007/1 Expiry: 26/08/2015

Hyogo-Pref. 672-8064,

As belowE.A.F. / Con CastSteelmakingJFE BARS & SHAPES CORPORATION Yokohamacarbon, carbon-manganese 150BilletsSemi-FinishedA 32Normal StrengthSectionsAH32, AH36, DH32, DH36 32Higher Strength

Ibaraki Pref.314-0111

Kashima Works7 Minamihama, Kamisu-city

Tel: +81 (0)299 90 5218 Fax: +81 (0)299 90 5201email: [email protected] web jfe-bs.co.jpSemi finished products as billets to nominal 150mm width and 12000mm nominal length to the maximum thickness shown above are approved for furtherprocessing for rolled products.

Certificate No. MD00/1920/0007/1 Expiry date: 27/01/2020

As belowB.O.S. / Con CastSteelmakingJFE STEEL CORPORATION KobeAs belowB.O.S. / Ingotcarbon, carbon-manganese, alloy 30Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 310Slabscarbon, carbon-manganese, alloy 750BloomsA, B, D, E 200Normal StrengthPlatesAH42, FH27S, FH32, FH36 50Higher StrengthDH42, DH46, DH50, DH55, DH62, DH69, EH42,EH46, EH50, EH55, EH62, EH69

75

AH40, DH40, EH40 80EH40S** 85EH47 90EH40S* 100AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

150

360AR, 410AR 40Boiler & Pressure Vessel360, 410 100360FG, 410FG, 460FG, 490FG, 510FG 1349Ni 40Ferritic Low TemperatureLTAH27S, LTAH32, LTAH36, LTDH27S, 50

As at 10 April 2018 50Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

JapanLTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

50Ferritic Low TemperaturePlates

304L, 316L 50Austenitic StainlessE/304L, E/316L 30CladA, B, D, AH27S, AH32, AH36, DH27S, AH40,DH32, DH36, DH40, EH27S, EH32, EH36, EH40

50Tapered

A, B, D, AH27S, AH32, DH27S, DH32 40Differential ThicknessA, B 16Normal StrengthHot Rolled Coil360, 410 16Boiler & Pressure VesselA, B, D 32Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

32Higher Strength

carbon, carbon-manganese 400StructuralBarsalloy 165Machinerycarbon-manganese 190U1, U2 130Chain Cable Stock

Kawasaki-DoriKurashiki

West Japan Works (Kurashiki)1 Mizushima

Tel: +81 (0)86 447 2652 Fax: +81 (0)86 447 2735 email: [email protected] www.jfe-steel.co.jp/works/west/

Certificate No. MD00/0838/0017/1 Expiry date: 14/10/2018

Ingot cast maximum thickness plate 200 mm.Continuous cast maximum thickness plate:Grade A Normalised: up to 200mm. Grades B and D Normalized: up to 155 mm. Other grades and conditions: up to 100mm.Specified through thickness properties on all plate grades.Thermo Mechanical = TMCPTM + Accelerated Cooling = TMCPTapered plates up to 8 mm/m taper ratio.Differential thickness plates, differential thickness 8mm by TMCP, 5mm by Normalized rolling.

MQS Approved - Approval No. MQS 022

As belowB.O.S. / Con CastSteelmakingJFE STEEL CORPORATION Kobecarbon, carbon-manganese, Normal strength,Higher Strength

300SlabsSemi-Finished

carbon, carbon-manganese, Normal Strength,Higher Strength

250Blooms/Billets

A, B, D, E 120Normal StrengthPlatesFH27S, FH32, FH36, FH40 80Higher StrengthEH40S* 85AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40, EH47,EH40*

100

360AR, 410AR 40Boiler & Pressure Vessel460FG, 490FG, 510FG 55360FG, 410FG 70LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36

40Ferritic Low Temperature

304L, 304LN, 316L, 316LN, 317L, 317LN 55Austenitic StainlessA to EH36/304L, A to EH36/316L 30CladA, DH34S, B, D, A,B, AH32, AH36, DH32,DH36, AH34S

50Differential Thickness

A, B, D, E 12Normal StrengthHot Rolled CoilAH27S, AH32 8Higher Strength460FG, 490FG 8Boiler & Pressure Vessel360, 410, 360FG, 410FG 12E 18Normal StrengthSectionsA, B, D 35AH40, DH40, EH40, FH27S, FH32, FH36 18Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

36

LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36

18Ferritic Low Temperature

As at 10 April 2018 51Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Fukuyama-cityHiroshima-pref.

West Japan Works (Fukuyama)1, Kokan-cho

Tel. (0)84 945 3160 Fax (0)84 945 3101 Email: [email protected] Web http://www.jfe-steel.co.jp

TM + Acc = OLAC process

For differential thickness plates, the maximum thickness differential for a thickness of 50mm is 10mm for normal strength grades and 6mm for higher strengthgrades

Approved for the supply of plates with specified through thickness properties (Z25/Z35).

MQS Approved - Approval No. MQS 005

Certificate No. MD00/1055/0015/1 Expiry date: 14/10/2018

721-8510

As belowB.O.S. / Con CastSteelmakingJFE STEEL CORPORATION YokohamaA, B, D, E 100Normal StrengthPlatesFH27S, FH32, FH36 42Higher StrengthAH42, DH42, EH42 83AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40

90

360AR, 410AR 40Boiler & Pressure Vessel360, 410, 460FG, 490FG, 510FG 50360FG, 410FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

42Ferritic Low Temperature

D, E 40Normal StrengthTapered Plates maxA, B 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, AH40, DH40, EH40

50Higher Strength

AH32, AH36 22Higher strengthTapered Plates max

Kawasaki-kuKawasaki

East Japan Works (Keihin)1-1, Ohgishima

Tel: +81 44 322 1185 Fax: +81 44 322 1510 Email: [email protected] plate grades with specified through thickness properties.Materials Quality Scheme Approved - Approval No. MQS 034Certificate No. D00/1056/0011/1 Expiry date: 28/10/2018

210-0868

austenitic stainlessB.O.S/V.O.D./Con CastSteelmakingJFE STEEL CORPORATION Yokohamaaustenitic stainless 275SlabsSemi-Finished

Chuo-kuChiba 260-0835

East Japan Works (Chiba)1, Kawasaki-cho

Tel: +81 43 262 2287 Fax: +81 43 262 2980email: [email protected] web: www.jfe-steel.co.uk

Certificate No.: MD00/4065/0002/1 Expiry Date: 06/08/2018

As belowB.O.S. / Con CastSteelmakingKOBE STEEL, LTD. KobeAs belowB.O.S. / IngotAs belowE.A.F. / Con CastAs belowE.A.F. / IngotA, B, D, E 150Normal StrengthPlatesDH42, DH50, DH55, DH62, DH69, EH42, EH50,EH55, EH62, EH69, FH40, FH42, FH46, FH50,FH55, FH62, FH69

50Higher Strength

AH46, DH46, EH46 60AH40, DH40, EH40 80FH27S, FH32, FH36 90AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

100

360AR, 410AR, 460AR 40Boiler & Pressure Vessel360, 410, 460, 490, 460FG, 490FG, 510FG 90360FG, 410FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

90Ferritic Low Temperature

A,B, D,E, HTS up to EH36 50Differential ThicknessA, B, D 13Normal StrengthHot Rolled Coil360FG, 410FG 13Boiler & Pressure Vessel

As at 10 April 2018 52Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

1 Kanazawa-choKakogawa-city

Kakogawa Works

Tel: +81 794 36 1151 Fax: +81 794 36 2079 Email: [email protected] grades with specified through thickness properties.Certificate No. MD00/0863/0010/1 Expiry date: 14/10/2018

Materials Quality Scheme Approved - Approval No. MQS 009

Hyogo-pref.

As belowB.O.S./Ingot/Con CastSteelmakingKOBE STEEL, LTD. Kobecarbon, carbon-manganese, alloy 8Ingots (tonnes)Semi-FinishedCarbon, Carbon-Manganese, Alloy 600Rolled Bloomscarbon, carbon-manganese, alloy 250Semi-finished ProductsBarsA 250Normal Strengthcarbon, carbon-manganese, alloy 250MachineryU1, U2, U3 160Chain Cable Stock

Nada-kuKobe

Kobe Works2 Nadahama-Higashimachi

Tel +81 78 882 8057 Fax +81 78 882 8211 email: [email protected] web: www.kobelco.co.jp

Certificate No. MD00/0864/0009/1 Expiry date: 06/08/2020

The maximum dimensions of bars rolled from continuously cast blooms are limited to 120 mm for alloy steels and 160 mm for all other grades.

As belowE.A.F. / Con CastSteelmakingKYOEI STEEL LTD. NagasakiA 16Normal StrengthSectionsA 53Normal StrengthBars

Sanyo-Onoda CityYamaguchi Prefecture

Yamaguchi DivisionOaza Onoda 6289-18

Tel: +81 836 83 6172 Fax: +81 836 83 0839 email [email protected] web www.kyoeisteel.co.jpCertificate No. MD00/1892/0007/1 Expiry date: 19/03/2019

756-0817

As belowE.A.F. / IngotSteelmakingMITSUBISHI STEEL MFG. CO., LTD. Yokohamacarbon, carbon-manganese 16Ingots (tonnes)Semi-Finished

Hirota, Kawahigashi-machiAizuwakamatsu-city

Hirota Works405, Aza Rokucho

tel: +81 (0) 242 75 3111 Fax: +81 (0) 242 75 2619 email [email protected] web: www.mitsubishisteel.co.jp

Certificate Number: MD00/1802/0003/1 Expiry: 28/02/2018

Ingots nominal 2050mm diameter x nominal 1250mm length to the above maximum weight are approved for further processing forgings.

Fukushima Pref. 969-3471

As below 20Ingots (tonnes)Semi-FinishedMITSUBISHI STEEL MURORAN INC. YokohamaAs below 515Blooms/Billetscarbon, carbon-manganese, alloy 270StructuralBarscarbon, carbon-manganese, alloy 210Machinery

Muroran shiHokkaido

Muroran Works12, Nakamachi

Tel: +81 (0)143 41 2831 Fax: +81 (0)143 41 2869 Email: [email protected]: www.mitsubishisteel.co.jpCertificate No. MD00/1893/0008/1 Expiry date: 07/04/2019

050-0087

A 38Normal StrengthBarsNIHON STEEL CO., LTD. KobeAH32, AH36 25Higher Strength

11, Rinkai-choKishiwada City

tel: +81 724 23 5151 Fax: +81 724 39 8357

Email mailto:[email protected]

Certificate No. MD00/2299/0007/1 Expiry date: 09/03/2020

Osaka

As at 10 April 2018 53Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

304L, 304LN, 316L, 316LN, 317L, 317LN, 321,347, 304S*, 316S*

55Austenitic StainlessPlatesNIPPON STEEL & SUMIKIN Nagasaki

UNS S31803 40Duplex StainlessA/304L, D/304L, D/316L 40Clad

2108-1, Oaza Maeda Aza HatoYawata Higashi-ku

STAINLESS STEEL CORPORATIONYawata Works

* Grades 304 and 316 may be accepted for approved applications.Tel; +81 93 672 2290 Fax: +81 93 672 2251 Email: mailto:[email protected]: http://nssc.nssmc.comCertificate No. MD00/1105/0010/1 Expiry date: 22/05/2018

Kitakyshi City, Fukuoka Pref.

austenitic stainless, duplex stainlessE.A.F. / Con CastSteelmakingNIPPON STEEL & SUMIKIN Nagasakiaustenitic stainless, duplex stainless 235SlabsSemi-Finished304L, 316L 8Austenitic StainlessPlates304L, 316L 8Austenitic StainlessHot Rolled Coil

3434 ShimataHikari City

STAINLESS STEEL CORPORATIONProduction Division, Hikari Works

Tel +81 833 71 5029 Fax +81 833 71 5215 Email: [email protected] No. MD00/3196/0005/1 Expiry date: 22/10/2020

Yamaguchi 743-8550

As belowB.O.S. / Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION

Yokohama

As belowSlabsSemi-Finished

carbon, carbon-manganese 300

carbon, carbon-manganese, alloy 165Blooms/Billets

A, B, D, E 100Normal StrengthPlates

AH42, DH42, EH42, FH42 50Higher Strength

AH46, AH50, DH46, DH50, EH46, EH50, FH46,FH50, FH69*, EH69*

70

AH40, DH40, EH40, FH40 80

AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36

100

360AR, 410AR 40Boiler & Pressure Vessel

360FG, 410FG, 460FG, 490FG, 510FG 100

LHAH42, LTAH46, LTAH50, LTDH42, LTDH46,LTDH50, LTEH42, LTEH46, LTEH50, LTFH42,LTFH46, LTFH50

50Ferritic Low Temperature

LTAH40, LTDH40, LTEH40, LTFH40 80

LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

100

A,B,D,E, HTS up to EH40 50Tapered

A,B,D,E, HTS up to EH40 50Differential Thickness

A, B, D 24Normal StrengthSections

AH27S, AH32, AH36, DH27S, DH32, DH36 19Higher Strength

A, B 12Normal StrengthPlates from coils

360, 410 12Boiler and Pressure Vessel

A, B 25Normal StrengthHot Coiled Strip

360, 410 25Boiler & Pressure Vessel

As at 10 April 2018 54Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Kimitsu-shiChiba-ken

Kimitsu Works1 Kimitsu

Materials Quality Scheme approved - MQS001

Semi Finished products include Carbon and Carbon-manganese as Fine Grain Al and Fine Grain Al+Nb slabs to 1500mm wide, to 10,400mm long (maximumweight 24T) and Carbon, Carbon-manganese and Alloy as Killed, Fine Grain Al and Fine Grain Al+Nb Blooms to 165mm diameter, to 11m long (amaximumweight 1.85T), all for further processing.

High strength fine grained Ti+Nb steel plates produced in the TM + Acc and TM + Acc + Temper conditions up to 70mm thickness are approved with Mn andAl contents to be outside that given in Lloyd's Register Materials Rules. Letter 'S' is used after identification number of non-standard composition materials.

Materials Quality Scheme covers Steelmaking and rolled plates only with exception of EH/FH69 grade. Strip, plate cut from coil, sections and EH/FH69 gradeapproved under Materials Survey Scheme (direct survey).

* Project specific approval only. Letter ref MAT/1100/GY/10641564 refers.

Tel: +81 (0)439 50 2194 Fax: +81 (0)439 55 8727

E-mail: [email protected] Website: www.nssmc.com/works/kimitsu/

Certificate No. MD00/1100/0014/1 Expiry date: 16/06/2020

299-1141

As BelowB.O.S./E.A.F./Ingot/Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION

Yokohama

carbon, carbon-manganese, alloy 190BilletsSemi-Finished

A, B 200Normal StrengthBars

AH32, AH36, DH32 200Higher Strength

U1, U2, U3, R3, R3S, R4 136Chain Cable Stock

API-2F 152

Muroran CityHokkaido

Muroran Works12, Naka-machi

Tel: +81 (0)143 47 2337 Fax: +81 (0)143 47 2783 Email: [email protected] Web: http://www.nssmc.con/works/muroranThe approval for bars intended for chain cable stock are for material rolled from continuous casting billets only.Bars for mooring grade chain cable stock in grades R3, R3S and R4 are restricted to Hamanaka Chain Mfg. Co. Ltd. Himeji plant only.Bars in Grade U3 in the above supply condition may be accepted up to 200mm diameter for the further processing for the production of forged chain cablefittings.Approval for billets, maximum 190mm x 190mm x 8000mm maximum weight 2.3 Tonnes, as semi finished products are for further processing for forgings.Certificate Number: MD00/1101/0013/1 Expiry date: 30/06/2020

050-8550

As belowB.O.S./Ingot/Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION

Kobe

A, B, D, E 130Normal StrengthPlates

FH27S 40Higher Strength

AH40, DH40 50

DH42, DH46, EH40, EH42, FH32, FH36, FH40,FH42

70

EH46, EH46S, FH46, FH46S 110

FH69* 120

DH50, DH55, DH62, DH69 200

AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

210

360AR, 410AR 40Boiler & Pressure Vessel

360, 410 115

360FG, 410FG, 460FG, 490FG, 510FG 120

LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

40Ferritic Low Temperature

As at 10 April 2018 55Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Tokai-machiTokai-city

Nagoya Works3, 5 Chome

Tel +81 52 603 7236 Fax +81 52 603 7229 Email: [email protected] grades and thicknesses with specified through thickness properties (Z35)Certificate No. MD00/1102/0013/1 Expiry date: 15/07/2019

Aichi Pref. 476-8686

As belowB.O.S. / Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION

Nagasaki

A, B, D, E 100Normal StrengthPlates

DH42, EH42, FH42 50Higher Strength

EH40S* 60

EH47-W430, EH47-W140 70

AH40, DH40, EH40, FH27S, FH32, FH36, FH40 80

EH47 90

AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, EH40*, EH47S, EH40S**

100

360AR, 410AR, 460AR 40Boiler & Pressure Vessel

360, 410, 460, 490 90

360FG, 410FG, 460FG, 490FG, 510FG 100

LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36, LTFH40

80Ferritic Low Temperature

AH40, DH40, EH40 30Tapered

A, B, D, E, A,B,D,E, AH27S, AH32, AH36,DH27S, DH32, DH36, EH27S, EH32, EH36

50

A,B,D 35Differential Thickness

A,B, A,B,D,E, AH27S, AH32, AH36, DH27S,DH32, DH36, EH27S, EH32, EH36

50

A 12Normal StrengthHot Rolled Coil

AH27S, AH32, AH36 12Higher Strength

360FG, 410FG, 460FG, 490FG, 510FG 12Boiler & Pressure Vessel

Oita-CityOita-Prefecture

Oita Works1, Oaza Nishinotsu

Tel +81 97 553 2122 Fax +81 97 553 2379

Email: [email protected]

Web http://www.nssmc.com/works/oita/index.html/

All plates with specified through thickness properties.* Plates in LLF27 and LLF33 up to a maximum thickness of 40 mm can be accepted for approved applications.* Plates in EH40S are for approved applications only and may have a Nickel content up to 1.5% with a carbon equivalent of 0.4%. The Approved thicknessrange of EH40S is 30mm to 60mm.* Plates in the H47 grades to be produced to the agreed chemistry ranges and agreed max CEVs.** EH40S is approved with demonstrated brittle crack arrest properties.

* EH40 is approved with demonstrated brittle crack arrest properties.

Materials Quality Scheme Approved - Approval No. MQS010

Certificate No. MD00/1103/0018/1 Expiry date: 29/03/2019

carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION

Yokohama

austenitic stainlessA.O.D./Con Cast

carbon, carbon-manganese 300SlabsSemi-Finished

A, B, D, E 150Normal StrengthPlates

As at 10 April 2018 56Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Japan 150Normal StrengthPlatesCORPORATION

FH27S 32Higher Strength

FH32, FH36 43

AH42, AH46, AH50, AH55, AH62, DH42, DH46,DH50, DH55, DH62

47

AH36S, AH40S, DH36S, DH40S, EH36S, EH40S 50

EH40* 80

EH47 90

EH40S* 100

AH36, AH40, DH36, DH40, EH27S, EH32, EH36,EH40

105

AH27S, AH32, DH27S, DH32 150

360AR, 410AR, 460AR 40Boiler & Pressure Vessel

510FG 55

360, 410, 460, 490 63

360FG, 410FG, 460FG, 490FG 100

5Ni 30Ferritic Low Temperature

LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

45

9Ni 50

EH36/304L, EH36/316L 38Clad

EH27S, EH32, EH36 32Differential Thickness

A,B,D, AH27S, AH32, AH36, DH27S, DH32,DH36

35

A, B, D, E 35Normal StrengthSections

AH40, DH40, EH27S, EH32, EH36 18Higher Strength

DH27S, DH32, DH36 20

AH27S, AH32, AH36 35

A, B, D 19Normal StrengthHot Coiled Strip

360FG, 360, 410FG, 410 19Boiler & Pressure Vessel

As at 10 April 2018 57Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Kashima CityIbaraki Pref.

Kashima Works3 Hikari

Tel +81 (0)299 84 2575 Fax +81 299 84 2945

E-mail: [email protected]

Website: www.sumitomometals.co.jp

All plates with specified through thickness properties.

Materials Quality Scheme Approved - Approval No. MQS 002

9Ni grade supplied in QLT condition: prior to tempering treatment,plates may be subjected to an intermediate heat treatment.Welding of 9Ni is restricted to a maximum heat input of 3KJ/mm.EN 10028-4 X8Ni9, X7Ni9 grades which show equivalence to Lloyd's Register 9Ni can be accepted for approved applications.

NSSMC’s NSGP-2 Corrosion Resistant Steel Grades are approved as below:

Plates AH32 RCW, DH32 RCW, AH36 RCW, DH36 RCW in the TM Condition fine grain treated with Al+Ti to athickness of 20mm with through thickness properties of Z35

Plates AH32 RCW, DH32 RCW, AH36 RCW, DH36 RCW in the TM+Acc Condition fine grain treated with Al+Ti to athickness of 30mm with through thickness properties of Z35

SMI's Fatigue Crack Arrester (FCA) grades by the DAC process with parent plate fatigue crack growth rates guaranteed by the manufacturer and tested inaccordance with ASTM E647 may be accepted for approved applications. Properties are to be as agreed with the Society. This acceptance does not implyconcessions on either design or survey requirements.

SMI's High Welding Heat Input Steel, may be accepted for approved applications, in all higher tensile strength grades up to EH40, in the TM + ACC conditionup to 105 mm thickness, when used in accordance with SMI's guidelines for welding or line heating. This acceptance does not imply concessions on eitherdesign or survey requirements.

SMICORE, may be accepted for approved applications, in all higher tensile strength grades up to EH36, in the TM condition up to 20mm thickness and the TM+ ACC condition up to 30 mm thickness. The steel is to have a guaranteed CRL of 0.5 or less and to be of approved composition. This acceptance does notimply concessions on either design or survey requirements.(Note CRL = Corrosion Ratio by Long term test)

NSSMC’s Steel Grades bearing Sn are approved as below:

Plates AH32, AH36, DH32 and DH36 in the TM condition fine grain treated with Al+Ti to a thickness of 25 mm with through-thickness properties of Z35

Plates AH32, AH36, DH32 and DH36 in the TM +Acc condition fine grain treated with Al+Ti to a thickness of 30 mm with through-thickness properties of Z35

Certificate No. MD00/1454/0029/1 Expiry date: 06/07/2019

314-0014

A 240Normal StrengthBarsNIPPON STEEL & SUMITOMO METALCORPORATION

Kobe

1, Nishino-choHigashi-Mukojima

Pipe & Tube UnitAmagasaki Works

Tel: +81 (0)6 6411 7616 Fax: +81 (0)6 6411 7612 Email: mailto:[email protected] No. MD00/1458/0009/1 Expiry date: 12/11/2019

Amagasaki, 660-0856

carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION

Kobe

austenitic stainlessA.O.D./Con Cast

Carbon, Carbon manganese 400Rolled BarsSemi-Finished

As at 10 April 2018 58Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

1850 MinatoWakayama-city

Wakayama Works (Wakayama & Kainan)

Tel: +81 (0) 73451 1133 Fax: +81 734 51 1103

E-Mail: [email protected]

Website: www.sumitomometals.co.jp

Approved for Semi-fhinished as rolled Round Billet with the diameter from 83mm to 400mm; As cast Round Billet with the diameter from 191mm to 453mm;As rolled Blooms 140mm x140mm to 550mm x 550mm; As cast Blooms 410mm x 530mm, 600mm x 670mm; As cast Slabs 700-1950mm x 227mm/250mm.

Certificate No. MD00/1748/0013/1 Expiry date: 24/06/2019

640-8555

A, B, D, E 50Normal StrengthSectionsNIPPON STEEL & SUMITOMO METALCORPORATION

Kobe

AH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength

Sakai cityOsaka

Wakayama Works [Sakai Area]1, Chikko Yawata-cho Sakai-Ku

Tel: +81 722 33 1179 Fax: +81 722 33 1185 Certificate No. MD00/4141/0005/1 Expiry: 08/07/2018

As belowE.A.F. / Con CastSteelmakingNIPPON YAKIN KOGYO Co., Ltd. YokohamaAs below, austenitic stainless 200SlabsSemi-Finished321, 347 10Austenitic StainlessPlates304L, 316L 53Fe-36Ni* 8Fe-Ni alloys304L, 316L, 321, 347 8Austenitic StainlessHot Rolled CoilFe-36Ni* 3Fe-Ni alloys

Kawasaki-kuKawasaki-shi

KAWASAKI PLANT4-2, Kojima-cho

Tel: +81 44 271 3045 Fax: +81 44 271 3044email mailto:[email protected] web www.nyk.co.jp

Certificate No. MD00/1109/0008/1 Expiry date: 31/05/2018

* accepted for approved applications

Kanagawa - ken 210-8558

austenitic stainless 200E.A.F./V.O.D./Con CastSteelmakingNISSHIN STEEL CO. LTD Nagasaki304L, 316L, 304*, 316* 9Austenitic StainlessHot Rolled Coil

4976, Nomuraminami-machi,Shunan City,

SHUNAN WORKS

Tel: +81-3-3216-6327 Fax: +81-3-3214-6325

Website: www.nisshin.steel.co.jp

Cert No: MD00/4481/0001/1 Expiry Date: 13/05/2018

Yamaguchi Pref, 746 8666

304L, 316L, 321, 347 8Austenitic StainlessHot Rolled CoilNISSHIN STEEL CO., LTD. Kobe

Hekinan-shiAichi- ken

Kinuura Works1, Hama-cho

Tel: +81 566 48 7218 Fax: +81 566 48 1596 Email: [email protected]: http://www.nisshin-steel.co.jp/enCertificate No. MD00/2338/0009/1 Expiry date: 20/05/2020

447-8610

As belowE.A.F. / Con CastSteelmakingOJI STEEL CO., LTD. Yokohamacarbon, carbon-manganese 170BilletsSemi-FinishedA 25Normal StrengthBarsAH32, AH36 25Higher Strength

As at 10 April 2018 59Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Ota-cityGunma Pref.

Gunma Works120, Nittasorimachi-cho

Tel: +81 276 56 2119 Fax: +81 276 56 3136 Email: mailto:[email protected]: www. oji-steel.co.jpCertificate No. MD00/1141/0007/1 Expiry date: 14/10/2017

370-0313

carbon, carbon-manganeseE.A.F. / Con CastSteelmakingOSAKA STEEL CO., LTD. KobeHigher Strength 185Blooms/BilletsSemi-FinishedNormal Strength 190A 15Normal StrengthSectionsAH32, AH36 12Higher Strength

1 Chikko Yawata-choSakai

Sakai Works

Tel +81 722 33 3901 Fax +81 722 33 3976

Certificate No. MD00/0821/0010/1 Expiry date: 20/05/2019

Osaka

As belowE.A.F. / Con CastSteelmakingOSAKA STEEL CO., LTD. Kobecarbon, carbon-manganese, Normal Strength,Higher Strength

165Blooms/BilletsSemi-Finished

A, B, D 15Normal StrengthSectionsAH32, AH36 12Higher Strength

9-3 Minami Okajima 1 ChomeTaisho-ku

Osaka - Okajima Works

Tel: +81 06 6552 1447 Fax: +81 06 6552 3184 Email: [email protected] :www.osaka-seitetu.co.jpCertificate No. MD00/1157/0007/1 Expiry date: 20/05/2019

Osaka 551-0021

alloy, austenitic stainlessE.A.F. / Con CastSteelmakingSANYO SPECIAL STEEL CO., LTD., KobeAs belowE.A.F. / Ingotcarbon, carbon-manganese, austenitic stainless 15Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy, austeniticstainless

380Blooms

A 220Normal StrengthBarsalloy 220MachineryU1, U2, U3 136Chain Cable Stock

Shikama-kuHimeji-shi

3007 Nakashima

Tel: +81 (0)792 35 6029 Fax: +81 (0)792 35 6027 email: [email protected] web: www.sanyo-steel.co.jp

Heat treatment sub contracted to Toyo Metal Treating Corporation, Takasago Plant No. 2, Takasago, Hyogo Pref., Japan.

Certificate No. MD00/1307/0013/1 Expiry date: 30/10/2019

672-8677

As belowE.A.F. / Con CastSteelmakingSHINKANSAI STEEL CORPORATION KobeA, B, D, E 38Normal StrengthSectionsAH32, AH36, DH32, DH36 38Higher Strength

5, Shiohama-choSakai-ku, Sakai

Sakai Works

Tel: +81 (0)72 228 5121 Fax: +81 (0)72 228 7119 Email: mailto:[email protected] Web: http://www.shinkansai-steel.co.jpCertificate No. MD00/0823/0010/1 Expiry date: 13/11/2020

Osaka 590-0981

As belowE.A.F. / Con CastSteelmakingSHINKANSAI STEEL CORPORATION KobeA, B, D 32Normal StrengthSectionsAH32, AH36, DH32, DH36 32Higher StrengthU1, U2, U3 80Chain Cable StockBars

4-26-1, Hoshida KitaKatano-shi

Hoshida Works

Tel: +81 (0)72 891 0624 Fax: +81 (0)72 893 1319 Email: [email protected] Web: http://www.shikansai-steel.co.jpCertificate No. MD00/1244/0008/1 Expiry date: 05/10/2018

Osaka

As at 10 April 2018 60Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowE.A.F. / IngotSteelmakingTHE JAPAN STEEL WORKS, LTD. YokohamaA, B, D, E 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50304L, 316L 65Austenitic StainlessAH32/304L, AH32/316L, AH32/316LN,AH32/317L

19Clad

AH32/S31803 30A/304L, B/304L, D/304L, E/304L, A/316L,B/316L, D/316L, E/316L

100

MuroranHokkaido

Muroran Plant4, Chatsu-machi

Tel +81 (0)143 22 0539 Fax +81 (0)143 22 5736 email: https://www.jsw.co.jp/en/contact/ web: www.jsw.co.jpCertificate No. MD00/1507/0008/1 Expiry date: 09/11/2018

051-8505

carbon, carbon-manganeseB.O.S. / Con CastSteelmakingTOKAI SPECIAL STEEL CO., LTD. Kobecarbon, carbon-manganese 370BloomsSemi-Finishedcarbon, carbon-manganese 155Billets

Tokai-MachiTokai-shi

3, 5-Chome

Tel +81 52 603 7236 Fax +81 52 603 7229 email: [email protected]

Certificate No. MD00/1542/0007/1 Expiry date: 01/02/2020

Aichi-ken

As belowE.A.F. / Con CastSteelmakingTOKYO STEEL MANUFACTURING CO., LTD. NagasakiA, B, D 32Normal StrengthPlates360AR, 410AR 32Boiler & Pressure VesselA 24Normal StrengthSections

Wakamatsu-kuKitakyushu City

Kyushu Plant3-5-1, Minami-Futajima

Tel: +81 93 701 2631 Mobile: +81 80 3974 1536 Fax: 81 93 791 2639 Email: mailto: [email protected] Web http://www.tokyosteel.co.jpCertificate No. MD00/1550/0009/1 Expiry date: 23/06/2017

Fukuoka 808-0109

As belowE.A.F. / Con CastSteelmakingTOPY INDUSTRIES, LTD. KobeE 20Normal StrengthSectionsA, B, D 35AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36

20Higher Strength

LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

20Ferritic Low Temperature

A, B, D, E 50Normal StrengthBarsAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength

1, Akemi-choToyohashi-shi

Toyohashi Works

Tel +81 532 25 1111 Fax +81 532 25 7401 Email: mailto: [email protected] web: http://www.topy.co.jpCertificate No. MD00/1555/0009/1 Expiry date: 15/06/2020

Aichi-ken, 441-8510

carbon, carbon-manganese, alloy 60E.A.F. / IngotSteelmakingTSUNEISHI IRON WORKS Co., Ltd Nagasaki

43-1 Koyo-machiWakamatsu-ward

Wakamatsu Steel Factory

Tel: +81 (0)93 752 0770 Fax:+86 (0)93 752 0777Email to: [email protected] Web: http://www.tsuneishi-iw.jp

Certificate No.: MD00/4392/0002/2 Expiry Date: 11/10/2020

Kitakyushu-city, 808-0002

As belowE.A.F. / Con CastSteelmakingYAMATO STEEL CO., LTD. KobeA, B, D, E 25Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

25Higher Strength

As at 10 April 2018 61Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

380, Kibi, Ohtsu-kuHimeji City

Tel: +81 (0)79 273 0716 Fax: +81 (0)79 272 0914 Email mailto: [email protected] Web:http://www.yamatokogyo.co.jpCertificate No. MD00/1687/00011/1 Expiry date: 09/06/2020

Hyogo-pref.

Korea

304L, 304LN, 316L, 316LN, 317L, 317LN, 321,347

8Austenitic Stainless SteelPlates from coilsBUSAN STEEL CO., LTD. Busan Port

29, Songjeuong-gil (Songjung-Dong),Gangseo-Gu

Tel: +82 51 831 3700, Fax No. +82 51 831 3701Email: [email protected]: www.busansteel.co.krCertificate No. MD00/4028/0002/1 Expiry date: 23/06/2018

Busan

304L, 304LN, 316L, 316LN 80Austenitic StainlessPlatesDK CORPORATION UlsanUNS S31803, UNS 32900*, UNS 32205* 50Duplex Stainless

66, Gohyeon-Gil, 98 Beon-gil,Cheongha-ri, Buk-gu, Pohang-si,

Tel: +82 (0)54 245 3062 Fax: +82 (0)54 245 3065 Email:mailto:[email protected] Web:http://www.dkcsteel.com*accepted for approved applicationsThe scope of approval is for the heat treatment and final testing of plates only from rolled plates supplied from approved works.Certificate Number: MD00/2230/0007/1 Expiry: 28/05/2019

Kyungsangbuk-do

A 12Normal StrengthSectionsDONG IL STEEL CO. LTD Busan PortAH32, AH36 12Higher Strength

50, Daedong-ro,193, Beon-gil, Sasang-gu,

SASANG WORKS

Tel No. + 82-51-323-1177 Fax No: + 820 - 325 6378

Website: www.dongilsteel.com

Certificate No: MD00/4517/0001/1 Expiry Date: 14/10/2015

Busan

carbon-manganeseE.A.F. / Con CastSteelmakingDONGKUK STEEL MILL Co. Ltd. Ulsancarbon-manganese 480Blooms/BilletsSemi-FinishedD, E 50Normal StrengthPlatesA, B 83AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36

50Higher Strength

460FG, 490FG, 510FG 35Boiler & Pressure Vessel360AR, 410AR 40360FG, 410FG 50LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

50Ferritic Low Temperature

D 25Normal StrengthSectionsA, B 32AH27S, DH32 25Higher StrengthAH32, DH27S 32

195, Cheolgangsandan-ro,Daesong-myeon, Nam-gu,

Pohang Works

Tel: +82 054 721 3261 Fax: +82 02 317 9055email: [email protected] web: www.dongkuk.comCertificate No. MD00/0414/0014/1 Expiry date: 13/05/2019

Billets to 150 x 150mm, Blooms to 200 x 250 & 250 x 300, Beam Blanks to 400 x 480 x 120mm.

Pohang-si, Gyeongsangbuk-do

E 83Normal StrengthPlatesDONGKUK STEEL MILL Co. Ltd. SeoulA, B, D 100FH32, FH36 50Higher StrengthAH32, AH36, AH40, DH32, DH36, DH40, EH32,EH36, EH40

83

460AR 35Boiler & Pressure Vessel360AR, 410AR 40490FG 50460FG, 510FG 70360FG, 410FG 100LTFH32, LTFH36 50Ferritic Low Temperature

As at 10 April 2018 62Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

25, Godaegongdan 1-gil,Song-ak-eup, Dangjin-si,

Dangjin Works

Tel: +82 (0) 41 351 4679 Fax: +82 (0) 41 317 9083 Email: [email protected] Web: http://www.dongkuksteel.co.kr

Certifcate Number: MD00/3773/0010/1 Expiry: 10/04/2019

Plates in the Normalised supply condition Fine Grain Al+V are only accepted in the thickness range >30mm to 70mm.

Approval includes Z grade plates with specified through thickness properties when tested in accordance with LR Rules requirements.

Chungcheongnam-do

A 20Normal StrengthPlates from coilsDONGYANG S.TEC. CO., LTD Ulsan

#619-12, Munduk-Ri,Ocheon-Eup Nam-Gu,

Tel: +82 54 292 6181 Fax: +82 54 291 6548Email: [email protected] www.dystec.co.krCertifcate Number: MD00/3840/0003/1 Expiry date: 26/09/2016

Pohang-city, Kyeongbuk,

carbon 16Structural SectionsFabricated SectionsDONGYEUN STEEL Co., LTD Busan Port

Jangan-eup,Gijang-gun,

Tel No: 0151 724 7800 Fax No: 051-724-8901

E-mail: [email protected] & [email protected]

Website: www.dongyeunsteel.com

Certificate No. MD00/4650/0001/1 Expiry Date: 09/01/2020

Busan.

As belowE.A.F. / IngotSteelmakingDOOSAN HEAVY INDUSTRIES & CONSTRUCTIONCO., LTD.

Changwon

carbon, carbon-manganese, alloy, austeniticstainless

500Ingots (tonnes)Semi-Finished

Seongsan-gu,Changwon,

Changwon Plant22, Doosanvolvo-ro,

Tel +82 55 278 4746 Fax no. +82 55 278 [email protected] web www.doosanheavy.comCertificate No. MD00/0883/0002/1 Expiry date 08/03/2019

Kyungnam,

B, D, E 18Normal StrengthSectionsFINE BESTEEL CO LTD ChangwonA 30DH32, DH36, EH32, EH36, FH32, FH36 18Higher StrengthAH27S, AH32, AH36 30LTAH32, LTDH32, LTEH32, LTFH32, LTFH36 18Ferritic Low Temperature

25-1 Ha-Ri, Changnyeong-Up,Changnyeong-Gun,

Tel: +82 (0)55 259 2076 / 2064 Fax: +82 (0)55 259 2070Email: [email protected] www.fine-besteel.comCertificate No. MD00/3659/0006/1 Expiry date: 09/09/2018

Gyeongnam,

As belowE.A.F. / Con CastSteelmakingHYUNDAI STEEL COMPANY Seoulcarbon, carbon-manganese 270BloomsSemi-Finishedcarbon, carbon-manganese 200BilletsA, B 32Normal StrengthSectionsAH27S, AH32, AH36 32Higher Strength

63, Jungbong-DaeroDong-Gu

Inchon Plant

Tel: +82 32 760 2753 Fax: +82 32 760 2866 Email: [email protected] Web: http://www.hyundai-steel.comSections flat bars up to 400 mm width.

Certificate No. MD00/0754/0011/1 Expiry date: 01/01/2020

Inchon

As belowE.A.F. / Con CastSteelmakingHYUNDAI STEEL COMPANY Ulsancarbon, carbon-manganese, alloyBlooms/BilletsSemi-Finishedcarbon, carbon-manganese, alloy 120BarsB, D, E 18Normal StrengthSectionsA 37AH27S, AH40, DH27S, DH40, EH27S, EH32,EH36, EH40, FH27S, FH32, FH36, FH40

18Higher Strength

As at 10 April 2018 63Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

KoreaAH32, AH36, DH32, DH36 37Higher StrengthSectionsHYUNDAI STEEL COMPANY UlsanLTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36, LTFH40

18Ferritic Low Temperature

carbon, carbon-manganese, alloy 120MachineryBarsR3S, R4 110Chain Cable StockU1, U2, U3, R3 150

6363, Donghaean-roNam-Gu, Pohang-si

Pohang Plant No. 1

Tel: +82 54 271 1479 Fax: +82 54 271 1512 Email: mailto:[email protected] Web: http://www.hyundai-steel.comCertificate No. MD00/0819/0017/1 Expiry date: 05/06/2019

Gyeongsangbuk-do

carbon-manganeseE.A.F. / Con CastSteelmakingHYUNDAI STEEL COMPANY UlsanA, B, D 16Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36

16Higher Strength

LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

16Ferritic Low Temperature

carbon, carbon-manganese, alloy 120Semi-finished ProductsBars

36, Cheolgang-ro 314 beon-gil,Nam-Gu, Pohang-si,

Pohang Plant No. 2

Tel No. +82 54 271 1479 Fax No. +82 54 271 1512Email mailto:[email protected]: www.hyundai-steel.com Certificate No. MD00/3084/0009/1 Expiry date: 04/06/2019

As BelowB.O.S./E.A.F./Con CastSteelmakingHYUNDAI STEEL COMPANY SeoulNormal strength, Higher Strength 300SlabsSemi-FinishedA, B 22Normal StrengthHot Rolled CoilAH32, AH36 22Higher StrengthA, B 22Normal StrengthPlates from coilsAH32, AH36 22Higher Strength

Songak-eupDangjin-si

HR Coil Plant1480, Bukbusaneop-ro

Tel: +82 41 680 1691 Fax +82 41 680 1699 Email; [email protected] Web: http://www.hyundai-steel.comSlabs with nominal 2200mm width x nominal 4400mm length Certificate No. MD00/3446/0005/1 Expiry date: 22/03/2020

Chungncheongnam-do

A, B, D, E 100Normal StrengthPlatesHYUNDAI STEEL COMPANY SeoulAH42, AH46, AH50, DH42, DH46, DH50, EH42,EH46, EH50, FH40, FH42, FH46, FH50

50Higher Strength

FH27S, FH32, FH36, EH40* 80EH47 83AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40,EH40S**

100

360AR, 410AR, 460AR 40Boiler & Pressure Vessel460FG, 490FG 83360FG, 410FG 100LTDH27S, LTDH32, LTDH36, LTFH27S,LTFH32, LTFH36

40Ferritic Low Temperature

As at 10 April 2018 64Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Songak-EupDangjin-Si

Dangjin Works1480, Bukbusaneop-ro

Tel: +82 41 680 1690 or 1685 Fax +82 41 680 1699 email; [email protected] web: http://www.hyundai-steel.com

Approval for plates in grades AH27S, AH32, AH36, 360AR, 410AR, and 460AR as rolled fine grain Al+V are restricted to the thickness range 20.0mm to35.0mm.Approval for plates in grades AH27S, AH32, AH36, AH40, DH27S, DH32, DH36, DH40, EH27S, EH32, EH36, EH40 for the TM+Acc fine grain Al+Nb+Tisupply condition are restricted to the thickness range >15.0mm to 83.0mm.Approval for plates in grades LTDH27S, LTDH32, LTDH36, LTFH27S, LTFH32, LTFH36 for the TM+Acc fine grain Al+Nb+Ti supply condition are restricted tothe thickness range >15.0mm to 40.0mm.Approval for plates in Normalising Rolled condition are restricted to maximum 3200mm width.Plates with specified through thickness properties may be accepted with the suffix Z35.EH40* is approved with demonstrated brittle crack arrest properties.Approved for corrosion resistant steel plates in grades AH27S RCB and AH32 RCB with Z35 through thickness properties to 40 mm maximum thickness in TMsupply condition with Al+Nb+Ti grain refining treatment.

Certificate Number: MD00/3761/0015/1 Expiry: 22/03/2019

Chungcheongnam-do

As belowE.A.F. / IngotSteelmakingHYUNDAI STEEL COMPANY Changwoncarbon, carbon-manganese, alloy 100Ingots (tonnes)Semi-Finished

Haeryong-myeonSuncheon City, Jeollanam-do

46, Yulchonsandan 5-ro

Tel: +82 61 760 7100 Fax: +82 61 725 7733 email: [email protected] web: www.sppycenergy.co.kr

Certificate Number: MD00/3866/0005/1 Expiry date: 11/12/2019

Zip code: 540856

carbon, carbon-manganese, alloy 123MachineryBarsJINYANG SPECIALTY STEEL Co., Ltd. Ulsan

Yeongcheon-si,Gyeongsangbuk-do,

149-9, Damtteul-gil,

Tel: +82 (0)54 335 3500 Fax: +82 (0)54 335 0355 Email: [email protected]: http:// www.jysteel.co.kr/mainCert No MD00/3897/0002/1 Expiry date: 22/03/2017

As belowE.A.F. / IngotSteelmakingKISCO Changwoncarbon, carbon-manganese, alloy 160Ingots (tonnes)Semi-Finished

ChangwonGyeongnam

12, Gongdan-ro103 beon-gil, Seongsan-gu

Tel +82 55 260 0746 Fax +82 55 282 4123 Email: [email protected] Web page http://www.kisco.co.kr

Certificate No. MD00/0884/0006/1 Expiry date: 10/01/2021

A 15Normal StrengthSectionsKOREA STEEL SHAPES CO., LTD Busan PortAH32, AH36, DH32, DH36, EH32, EH36 15Higher StrengthA 65Normal StrengthBarsAH32 30Higher Strength

84, Noksansandan 407-Ro,Gangseo-Gu

Noksan Works

Tel: +82 51 310 8912 Fax: +82 51 831 3951email [email protected] web www.ekosco.com

Certificate No. MD00/3096/0009/1 Expiry date: 20/01/2020

Busan,

As belowE.A.F. / Con CastSteelmakingKOREA STEEL SHAPES CO., LTD Changwoncarbon, carbon-manganese, Normal Strength,Higher Strength

220BilletsSemi-Finished

98, Gongdandong-gil, Chilseo-Myeon,Haman-Gun,

Chilseo Works

Tel: +82 55 589 1159 Fax: +82 55 589 1116email: [email protected] web: www.ekosco.com

Certificate No. MD00/3097/0002/1 Expiry date: 10/10/2017

Gyeongnam,

As at 10 April 2018 65Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

austenitic stainless 85MachineryBarsKWANG JIN IND CO. LTD. Busan Portalloy 93carbon, carbon-manganese 100

160, Hasinjungang-ro,Saha-gu,

Tel No: +82 51 220 9264 Fax No. +82 51 204 9172Email: [email protected] Address www.kjsteel.co.krCert No MD00/3758/0003/1 Expiry date 14.03.2019

Busan,604-030

As belowB.O.S. / Con CastSteelmakingPOSCO Gwangyang Works ChangwonNormal strength, Higher Strength 300SlabsSemi-FinishedA, B, D, E 100Normal StrengthPlatesAH40, DH40, EH40, EH47 80Higher StrengthFH36, FH40 90AH27S, AH32, AH36, AH62, AH69, DH27S,DH32, DH36, DH62, DH69, EH27S, EH32, EH36,EH62, EH69, FH27S, FH32

100

360AR, 410AR, 460FG, 490FG, 510FG 35Boiler & Pressure Vessel360FG, 410FG 80LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

40Ferritic Low Temperature

A, B, D 22Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 12Higher Strength360AR, 410AR 12Boiler & Pressure Vessel

Gwangyang-si,Jeollanam-do,

20-26, Pokposarang-gil,

Tel: +82 2 3457 3838 Fax: +82 2 3457 6419 Email: [email protected] Web: www.posco.comApproved for semi-finished products, slabs, nominal 1750mm wide x 6000mm long.Hot rolled coils in normal strength grades in the supply condition thermomechanical fine grain aluminium are restricted to the thickness ranges >12 to 22mm.Certificate Number: MD00/3086/0015/1 Expiry: 13/07/2020

545-711

As BelowB.O.S./E.A.F./Con CastSteelmakingPOSCO Pohang Works Ulsancarbon, carbon-manganese, alloy, Normalstrength, Higher Strength

400SlabsSemi-Finished

A, B, D, E 100Normal StrengthPlatesFH27S, FH32, FH36 83Higher StrengthAH40, DH40, EH40 90AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, EH40S*, EH47

100

360AR, 410AR 40Boiler & Pressure Vessel460FG, 490FG, 510FG 90360FG, 410FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36

50Ferritic Low Temperature

304L, 304LN, 316L, 316LN 80Austenitic StainlessUNS S31803, UNS 32900*, UNS 32205* 50Duplex StainlessA, B, D, AH32, AH36, DH32, DH36 35TaperedE 12Normal StrengthHot Rolled CoilA, B, D 22EH27S, EH32, EH36 16Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36 22460FG, 490FG, 510FG 12Boiler & Pressure Vessel360FG, 410FG 22304L, 316L 8Austenitic Stainless

Nam-gu,Pohang si,

(Goedong-dong), 6261, Donghaean-ro,

Tel: +82 2 3457 3838 Fax: +82 2 3457 6000 email: [email protected] web: www.posco.com

Certificate No. MD00/1206/0022/1 Expiry date: 29/04/2019

* EH40S grade is approved with demonstrated crack arrest properties.

Applicable plate grades may be accepted with through thickness properties when manufactured and tested in accordance with the relevant Rules.

Slabs as semi-finished products nominal maximum width 2200mm x nominal maximum length 5000mm to the above maximum thickness are approved forfurther processing for rolled and forged products

Gyeongsangbuk-do,

As at 10 April 2018 66Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

A 18Normal StrengthPlates from coilsS & STEEL CO., LTD. Busan PortAH36 10Higher StrengthAH27S, AH32 15

1620 Dadae-dong, Saha-guBusanTel: +82 51 262 7525 Fax: +82 51 924 7902 Email: [email protected] Web: http://www.sdstl.co.krCertificate No. MD00/3523/0006/1 Expiry date: 23/09/2017

As belowE.A.F./Ingot/Con CastSteelmakingSeAH BESTEEL CORPORATION Mokpocarbon, carbon-manganese, alloy 155Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 510Bloomscarbon, carbon-manganese 180Billetsalloy 350Barscarbon, carbon-manganese, alloy 300MachineryBarsR5 140Chain Cable StockR4S, R4S 146R4 155U1, U2, U3, R3, R3S 165

Gunsan CityJeonlabuk-Do

Gunsan Plant1-6, Soryong-Dong

Tel: +82 63 460 8078 Fax: +82 63 460 8099 email: [email protected] web: www.seah.co.kr

Certificate No. MD00/1749/0014/1 Expiry date: 04/04/2018

Approval for Chain Cable Stock Grades R3, R3S, R4, R4S and R5 is restricted to supply to DAI HAN ANCHOR CHAIN MFG CO. LTD and Grades R3, R3Sand R4 to Pu Sung Metal Co., Ltd.Semi Finished Products - Ingots, Carbon & Carbon-manganese nominal sizes 2100 / 2350mm diameter x 2800mm long, and Alloy nominal sizes 2350 / 2600mmdiameter x 3050mm long, to the above maximum weight approved for further processing for forgings. Semi Finished Products - Blooms to nominal 390mm width x 5400mm length, to above maximum thickness approved for further processing for Forgings andRolled Products. Semi Finished Products - Billets to nominal 180 width x 11500mm length, to above maximum thickness approved for further processing for Rolled Products.Alloy grade bars as semi-finished products nominal maximum length 12,000mm to the above maximum diameter are approved for further processing for forgedproducts.

As belowE.A.F. / IngotSteelmakingSeAH CHANGWON INTEGRATED SPECIAL STEEL Changwonduplex stainless 17Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy, austeniticstainless

150

carbon, carbon-manganese, alloy, duplexstainless

150StructuralBars

austenitic stainless 170carbon, carbon-manganese, alloy 150Machinery

Seongsan-GuChangwon,

CORPORATION147,Jeokhyeon-Ro

Tel: +82 (0)55 269 6200 Fax: +82 (0)55 269 6907 Email: [email protected] http://www.poscoss.comCertificate No. MD00/1294/014/1 Expiry date: 07/08/2020

Gyeongnam

As belowE.A.F./V.O.D./Con CastSteelmakingTAEWOONG CO., LTD. Busan PortAs belowE.A.F/A.O.D/Ingotaustenitic stainless 30Ingots (tonnes)Semi-Finishedalloy 100carbon, carbon-manganese 150austenitic stainless 600Bloomscarbon, carbon-manganese, alloy 800

15, Hwajeonsandan 1-ro,Gangseo-gu,

Taewoong Steelmaking Business Unit

Tel: +82-51-329-5142 Fax: +82-51-329-5141

E-mail: [email protected]

Website: www.taewoong.com

Certificate No: MD00/4662/0002/1 Expiry Date: 20/02/2020

Busan, 46740.

As at 10 April 2018 67Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowB.O.S. / Con CastSteelmakingYK STEEL CORP. Busan PortA 7Normal StrengthSectionsA 32Normal StrengthBars

Saha-Gu604-817

760 Eulsukdo-daero,

Tel. +82 (0)51 260 2186 Fax +82 (0)51 265 2399 Email: [email protected] Web: http://www.yksteel.co.krCertificate No. MD00/0650/0008/1 Expiry date: 25/05/2017

Busan

304L, 316L 13Austenitic Stainless SteelPlates from coilsYOUNG GWANG STAINLESS CO., LTD. Busan PortUNS S32750 6Duplex StainlessUNS S31803 8

Gangseo-guBusan

16, Noksansandan 262-ro

Tel: +82.51.832.1911 Fax: +82.51.832.1909 Email to: [email protected] Web: http://www.ygs.c.kr

Certificate No. MD00/4460/0001/1 Expiry date: 31/03/2018

304L, 316L 13Austenitic Stainless SteelPlates from coilsYOUNG GWANG STAINLESS CO., LTD. Busan PortUNS S32750 6Duplex StainlessUNS S31803 8

406, Noksansaneopjung-roTel: +82.51.832.1911 Fax: +82.51.832.1909 Email to: [email protected] Web: http://www.ygs.c.kr

Certificate No. MD00/4460/0001/1 Expiry date: 31/03/2018

Luxembourg

As belowE.A.F. / Con CastSteelmakingARCELORMITTAL BELVAL ET DIFFERDANGE LyonNormal Strength, Higher Strength 100BloomsSemi-FinishedA, B 26Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

26Higher Strength

66 rue de LuxembourgL4009 Esch sur Alzette

BELVAL MILLTMB Rolling Plant

Tel: +352 58 2885 Fax: +352 5835 81 Email: mailto:[email protected]:www.arcelor.comCertificate #: MD00/0030/0008/1 Expiry date: 04/11/2018

As belowE.A.F. / Con CastSteelmakingARCELORMITTAL BELVAL ET DIFFERDANGE LyonHigher Strength 135BloomsSemi-FinishedA, B 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

40Higher StrengthSections

L 4009 Esch sur AlzetteDifferdange Mill

Tel: +352 58 2028 85 Fax: +352 5835 81 Email: [email protected] Web http://www.arcelormittal.comBeam Blanks as semi-finished products (referred to as blooms above) nominal 500mm overall width x nominal 1150mm overall length, to the above overallmaximum thickness Certificate Number: MD00/0032/0008/1 Expiry: 10/03/2019

A, B 30Normal StrengthSectionsARCELORMITTAL RODANGE ET SCHIFFLANGE LyonAH32, AH36, DH32, DH36 30Higher Strength

2, Rue de L'industrieL-4801 Rodange

Rodange Mill

Tel: +352 58 20 28 84 Fax: +352 58 20 35 81 email: :[email protected] web www.arcelor.comCertificate No. MD00/2266/0007/1 Expiry date: 16/01/2019

As at 10 April 2018 68Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Macedonia

A 35Normal StrengthFabricated SectionsFAKOM A.D. BeogradAH36, DH36, EH36 40Higher Strength

POB 4391000 SKOPJE

St. Aleksandar Makedonski No.5

Tel No.: +389 317 4023, Fax: +389 317 3564 email: mailto:[email protected] Web http://www.fakom.com.mkCertificate No. MD00/2856/0008/1 Expiry date: 26/11/2018

As belowE.A.F. / Con CastSteelmakingMAKSTIL A.D.- SKOPJE BeogradA, B, D 100Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 50Higher Strength360AR, 410AR, 460AR 40Boiler & Pressure Vessel360, 410, 460, 490, 460FG, 490FG, 510FG 50360FG, 410FG 100

XVI Makedonska brigada 18P.O. Box 599

Tel: +389 2 328 7130 email: [email protected] web www.makstil.comSpecified through thickness properties for plates up to 50 mm thicknessCertificate No. MD00/2216/0008/1 Expiry date: 21/05/2019

1000-Skopje

Malaysia

A 30Normal StrengthPlatesJI KANG DIMENSI Sdn. Bhd. Kuala Lumpur

26100 KuantanPahang Darul Makmur

Lot 69-71, Kawasan Perindustrian Gebeng

Tel: +609 583 9881 Fax: +609 583 4551 Email: mailto: [email protected]: www.jikangdimensi.comCertificate No. MD00/3022/0005/1 Expiry date: 27/06/2018

Mexico

carbon, carbon-manganeseE.A.F. / Con CastSteelmakingARCELORMITTAL LAZARO CARDENAS, S.A. deC.V.

Metepec/Veracruz

carbon, carbon-manganese 250SlabsSemi-Finished

60950- Lázaro CárdenasMichoacan

Av Francisco J. Mujica N° 1-B

Steel types carbon and carbon-manganese cover the supply of blooms for processing into normal strength, high strength and ferritic steels for low temperatureservice according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The final processing mill is responsible forordering steel which complies with their approved chemical composition and enables them to achieve the required mechanical properties

Tel: +52 753 533 1917 Fax: +52 753 533 1187 Email: [email protected] Web http://www.arcelormittal..comCertificate No. MD00/0783/0007/1 Expiry date: 08/01/2017

As at 10 April 2018 69Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Montenegro

Carbon, Carbon-manganese, Alloy 7EAF/LRF/VD/IngotSteelmakingTOS�ELIK NIKŠI� d.o.o. Beograd

Vuka Karadzica bb,81400 NiksicTel: +382 40 202 222 email: [email protected]

Certificate No: MD00/4508/0001/1 Expiry Date: 03/09/2018

Norway

carbon, carbon-manganeseE.A.F. / Con CastSteelmakingCELSA ARMERINGSSTÅL AS OsloA, carbon, carbon-manganese 160BilletsSemi-Finished

PO Box 500N-8601 Mo i Rana

Mo Industripark

Tel: +47 91886913 Mob: +47 911 10493 Email: [email protected] Web http://www.celsanordic.comCertificate No. MD00/2103/0007/1 Expiry date: 05/09/2020

Poland

carbon, carbon-manganese, alloy, austeniticstainless

E.A.F. / IngotSteelmakingALCHEMIA S.A. Katowice

carbon, carbon-manganese, alloy, austeniticstainless

14Ingots (tonnes)Semi-Finished

ul.Dyrekcyjna 641-506 Chorzów

ODDZIAL STALOWNIA BATORY W CHORZOWIE

Tel: +48 883 301310

E-mail: [email protected]

Website: www.alchemiasa.pl

Certificate No. MD00/0711/0013/1 Expiry date: 05/10/2019

As belowB.O.S. / Con CastSteelmakingARCELORMITTAL POLAND S.A. Katowicecarbon, carbon-manganese 220SlabsSemi-FinishedA, B, D 15Normal StrengthHot Rolled CoilAH27S, AH32 16Higher StrengthA, B, D 15Normal StrengthPlates from coilsAH27S, AH32 16Higher Strength410 FG, 360 FG, 460 FG 16Boiler and Pressure Vessel

30-969 Kraków

ODDZIAL W KRAKOWIEul. Ujastek 1

Tel: +48 12 290 1817 Fax: +48 12 290 5591email: [email protected] web: www.arcelormittal.com/poland

Slabs as semi finished products are approved for further processing for rolled products to the maximum thickness shown above and nominal 1580mm widthand 11000mm length.Coils and plates are approved to maximum 2100mm width.

Certificate #: MD00/0707/0012/1 Expiry date: 25/01/2020

carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingARCELORMITTAL POLAND S.A. Katowicecarbon, carbon-manganese 300SlabsSemi-Finishedcarbon, carbon-manganese, Alloy 280Blooms/Billets

41-308 Dabrowa Gornicza

Oddzial w Dabrowie GorniczejAl. J. Pilsudskiego 92

Tel: +48 32 776 87 14 Fax: +48 32 776 84 86 Email [email protected] Web: http://www.arcelormitta.com/poland/

Certificate No. MD00/0717/0011/1 Expiry date: 05/02/2018

As belowE.A.F./Ingot/Con CastSteelmakingARCELORMITTAL WARSZAWA Sp. z.o.o. Katowicecarbon, carbon-manganese, alloy 25Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 220Blooms/Billetscarbon, carbon-manganese, alloy 65StructuralBarscarbon, carbon-manganese, alloy 65Machinery

As at 10 April 2018 70Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

ul. Kasprowicza 13201-949 WarszawaTel: +48 22 835 8081 Fax: +48 22 835 8638Email: mailto:[email protected] Web: http://www.arcelormittal-warszawa.comCertificate No. MD00/0720/0008/1 Expiry date: 01/08/2018

As belowE.A.F. / IngotSteelmakingCELSA "HUTA OSTROWIEC" Sp. z o.o. Katowicecarbon, carbon-manganese, alloy 130Ingots (tonnes)Semi-Finished

ul. Samsonowicza 227-400 Ostrowiec Swietokrzyski

ZAKLAD WYROBOW KUTYCH

Tel: +48 (0)41 2492905

E-Mail: [email protected]

Web page http://www.celsaho.com

Certificate No. MD00/2006/0008/1 Expiry date: 24/10/2019

Ingots size maximum 130 MT 2.33 m diameter

As belowE.A.F. / Con CastSteelmakingCMC POLAND Sp. z.o.o. Katowicecarbon, carbon manganese 160Blooms/BilletsSemi-FinishedA, B, D 25Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36 25Higher Strength

ul. Pilsudskiego 8242-400 ZawiercieTel: +48 32 672 5353 Fax: +48 32 672 5134 Mobile: +48 695 105211 Email: [email protected] Web: www.cmcpoland.comCertificate No. MD00/3594/0005/1 Expiry date: 05/05/2018

Approval for sections covers wide flats to 200mm width and flat bars to 150mm width.

.

As belowE.A.F. / Con CastSteelmakingCOGNOR S.A. Katowicecarbon, carbon-manganese, alloy 160BilletsSemi-Finished

ul. Zawadzkiego 4744-109 Gliwice

ODDZIAL FERROSTAL LABEDY W GLIWICACH

Tel: +48 32 234 7600 Fax: +48 32 234 7650 Mob +48 508032685EMail mailto:[email protected] Web page http://www.ferrostal.com.plCertificate No. MD00/2307/0007/1 Expiry date: 29/03/2020

Carbon, Carbon-manganese, Alloy 15EAF/LRF/VD/IngotSteelmakingCOGNOR S.A. Katowicecarbon, carbon-manganese, alloy 15Ingots (tonnes)Semi-Finished

ul.Kwiatkowskiego 1,37-450 Stalowa Wola

Oddziaž HSJ w Stalowej Woli

Tel: +48 15 813 51 84 Fax: +48 15 844 23 06email: [email protected] web: www.hsjsa.pl

Certificate No: MD00/4745/0001/1 Expiry Date: 26/03/2021

Carbon, Carbon-Manganese, Alloy 300Rolled BilletsSemi-FinishedHUTA BANKOWA Sp. z o.o. KatowiceCarbon, Carbon-manganese, Alloy 250Rolled Round BarsA, B 20Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strengthcarbon, carbon-manganese 250StructuralBarscarbon, carbon-manganese, alloy 250MachineryU1, U2 160Chain Cable Stock

ul. Sobieskiego 2441-300 Dabrowa GórniczaTel +48 32 295 7477Email: [email protected];[email protected] Web http://www.hutabankowa.com.plCertificate No. MD00/0716/0009/1 Expiry date: 04/03/2019

A, B, D, E 100Normal StrengthPlatesHW PIETRZAK HOLDING Sp. z o.o. KatowiceAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

100Higher Strength

360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100A/304L 50Clad

As at 10 April 2018 71Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

41-506 Chorzów

Oddzial Walcownia Blach Batory w Chorzowieul. Lesna 42

Tel: +48 604936263 or +48 32 7722525 email: [email protected]: www.pietrzak-holding.pl

All plates with specified through thickness propertiesCertificate No. MD00/2766/0007/1 Expiry date: 17/10/2016

As belowE.A.F. / Con CastSteelmakingISD HUTA CZESTOCHOWA Sp. z o.o. Katowicecarbon, carbon-manganese 250SlabsSemi-Finishedcarbon, carbon-manganese 280BloomsE 50Normal StrengthPlatesA, B, D 75AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

50Higher Strength

360AR, 410AR, 460AR, 460FG, 490FG, 510FG 50Boiler & Pressure Vessel360FG, 410FG 75

42-207 Czestochowaul. Kucelinska 22

Above plate grades may also be supplied with Z25/Z35 through thickness property requirements.

Tel: +48 34 323 8147 Fax: +48 34 323 0034 Email: [email protected] Web: http://www.isd- hcz.com.plCertificate No. MD00/0713/0013/1 Expiry date: 05/04/2018

carbon, carbon-manganese, alloy 150StructuralBarsWALCOWNIE BRUZDOWE "BATORY" Sp. z.o.o. Katowicecarbon, carbon-manganese, alloy 150Machinery

41-500 Chorzówul. Zelazna 22

Tel: +48 32 241 77 38 Fax: +48 32 241 77 55email [email protected] web: www.wbb.net.pl

Certificate No. MD00/3545/0003/1 Expiry date: 30/11/2017

Romania

As belowB.O.S./Ingot/Con CastSteelmakingARCELORMITTAL GALATI S.A. GalatzA, B, D, E 100Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

100Higher Strength

360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100

800698 GalatiSos Smardan Nr.1

Tel: +40 236 802100 Fax: +40 236 802101

E-mail: [email protected]

Website: www.arcelormittal.com

Approval includes for plates with specified through thickness properties, designation Z35, in all grades up to 60 mm thickness in the normalized condition.

Certificate No. MD00/0333/0009/1 Expiry date: 01/12/2019

As belowE.A.F. / Con CastSteelmakingCOS TARGOVISTE S.A. Galatzcarbon, carbon manganese, Alloy 150Blooms/BilletsSemi-FinishedU1, U2, U3 95Chain Cable StockBars

Sos. Gaiesti, 9-11Jud Dambovita, 130087

Targoviste

Tel: +40 758 837 264 Fax: +40 245 213 322 email: [email protected] Web: www.cos-tgv.ro

Certificate No. MD00/2293/0007/1 Expiry date: 12/02/2020

carbon, carbon-manganese, alloy 250E.A.F. / IngotSteelmakingDOOSAN IMGB S.A Galatzcarbon, carbon-manganese, alloy 250Ingots (tonnes)Semi-Finished

Berceni Road Nr. 104Sector 4

Tel: +40 21 301 2849 Fax: +40 21 301 2502 E-mail: [email protected]

Web: www.doosanimgb.com

Certificate No. MD00/1259/0003/1 Expiry date: 08/09/2020

041919 Bucharest

As at 10 April 2018 72Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

carbon, carbon-manganese, alloy 250StructuralBarsS.C. DONALAM S.R.L Galatzcarbon, carbon-manganese, alloy 150Machinery

Str. Prelungirea Bucuresti, nr 162,910125 CalarasiTel: +40 242 307 500 Fax: +40 242 306 913email: [email protected] web: www.grupobeltrame.com

Certificate No: MD00/4439/0001/1 Expiry Date: 05/03/2018

A 50Normal StrengthSectionsS.C. LAMINORUL S.A. - BRAILA GalatzAH27S, AH32, AH36, DH32, DH36 12Higher StrengthA 50Normal StrengthBars

810461 BrailaSos. Industria Sarmei nr. 2

Tel +40 239 669 388 Fax +40 374 092 038 Email: [email protected]

Website: www.laminorul.ro

Certificate No. MD00/1916/0009/1 Expiry date: 29/03/2018

carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingTMK-RESITA S.A. Galatzalloy 177BilletsSemi-Finishedcarbon, carbon-manganese 280

Traian Lalescu No. 36Caras-SeverinTel: +40 (0)255 217211 Fax: +40 (0)255 211883 Email: office.resita.tmk-artrom.roWeb http://www.tmk-artrom.roCertificate No. MD00/3804/0003/1 Expiry date: 07/07/2019

Russia

A, B, D 14Normal StrengthSections"RM - steel" Ltd. St. PetersburgAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36

14Higher Strength

11, Sedova street192019, St PetersburgTel: +7 812 318 0015 Fax: +7 812 568 0015 Email: mailto:[email protected] Web http//www.rm-steel.comCertificate No. MD00/1910/0010/1 Expiry date: 14/01/2020

carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingCHELYABINSK METALLURGICAL PLANT PAO St. Petersburgcarbon, carbon-manganese, alloy 20Ingots (tonnes)Semi-Finished

2nd Paveletskaya ul, 14454047- Chelyabinsk

Tel; +7 351 725 57 27 Fax: +7 351 725 51 76email [email protected] web: www.mechel.ruIngots supllied as semi finished products are for further processing for forgings.Certificate No. MD00/3262/0007/1 Expiry date: 10/08/2018

carbon, carbon-manganeseB.O.S. / Con CastSteelmakingJOINT STOCK COMPANY St. PetersburgNormal strength, Higher Strength 300SlabsSemi-Finished

1, Metallurgov Str.,Nizhny Tagil,

"EVRAZ NIZHNY TAGIL METALLURGICAL PLANT"

Tel:+007 3435 490611 Fax:+007 3435 496169 Email:mailto:[email protected] Web http://www.ntmk.ruCertificate No. MD00/2660/0007/1 Expiry date: 04/04/2018

Sverdlovsk Region, 622025

carbon, carbon-manganeseE.A.F. / Con CastSteelmakingJOINT STOCK COMPANY St. Petersburgcarbon, carbon-manganese, Normal Strength,Higher Strength

300BloomsSemi-Finished

U1, U2, U3 80Chain Cable StockBars

309515, BelgorodStary Oskol

"OSKOL ELECTROMETALLURGICAL PLANT"pr. Alekseya Ugarova 218/2

Tel +07 4725 375364 Fax +07 4725 373755 [email protected] Web http://www.oemk.ruBlooms as semi finished products; normal strength and higher strength; nominal 360mm maximum width x nominal 12,000mm maximum length.Blooms as semi finished products; carbon and carbon-manganese; nominal 360mm maximum width x nominal 12,000mm maximum length.Certificate Number: MD00/3065/0006/1 Expiry: 24/02/2019

As at 10 April 2018 73Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowE.A.F. / Con CastSteelmakingJSC ''Ural Steel'' St. PetersburgB, D 40Normal StrengthPlatesA 50AH32, AH36 40Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 40Boiler & Pressure Vessel

NovotroitiskOrenburg Region

1, Zavodskaya Street

Tel: +7 3537 66 20 66 Fax: +7 3537 66 25 27 Email: [email protected] Web: http://www.uralsteel.comCertificate No. MD00/2337/0009/1 Expiry date: 30/03/2020

462353

As belowE.A.F/A.O.D/IngotSteelmakingJSC KIROVSKIY ZAVOD St. Petersburgcarbon, carbon-manganese 120Semi-finished ProductsBars

47 Stachek Prospect198097 St. Petersburg

Petrostal Steel Works

Tel: +7 812 702 02 23 Fax: +7 812 702 04 66 email: [email protected] web: http://www.petrostal.spb.ru

Certificate No. MD00/1751/0007/1 Expiry: 29/01/2018

As belowE.A.F./Ingot/Con CastSteelmakingMOTOVILIKHA-GRAZHDANSKOYEMASHINOSTROENIE, LLC

St. Petersburg

carbon 17Ingots (tonnes)Semi-Finished

As below 450Blooms/Billets

614014, Perm1905 Street, 35Tel +8 342 260 7317 Fax +8 342 260 7959 Email: [email protected] Web: http://www.mzperm.ruCertificate No. MD00/4608/0002/1 Expiry date: 08/09/2019

As belowB.O.S. / Con CastSteelmakingNovolipetsk Steel St. PetersburgNormal strength, Higher Strength 355SlabsSemi-FinishedA, B, D 16Normal StrengthHot Rolled CoilAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH36, EH40

12Higher Strength

460FG, 490FG 10Boiler & Pressure Vessel360, 410, 360FG, 410FG 16

Pl. Metallurgov 2, NLMKLipetsk

398040, Russia

Tel: +7 795 034 44 45

Email: [email protected] & [email protected]

Web:http://www.nlmk.ru

Certificate No. MD00/1124/0007/1 Expiry date: 04/11/2019

A, B, D, E 40Normal StrengthPlatesPAO SEVERSTAL St. PetersburgEH27S, EH32 32Higher StrengthAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH40

40

360, 410 32Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 40

30 Mira Street162699 Cherepovets

Rolling Mill 2800

Tel: +7 8202 531146 Fax: +7 8202 53 2424 EMail: mailto:[email protected] Web http://www.severstal.ruPlates in the As Rolled, Normalized, Quenched and Tempered conditions with specified through thickness properties.Plates in the Normalizing rolled condition to 2200mm maximum width.Certificate #: MD00/0298/0011/1 Expiry date : 12/06/2019

Vologda Region

A 15Normal StrengthPlatesPAO SEVERSTAL St. PetersburgA, B, D, E 12Normal StrengthHot Rolled CoilAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40

12Higher Strength

360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 12Boiler & Pressure Vessel

30 Mira StrRolling Mill 2000

Tel: +7 8202 53 11 46 Fax: +7 8202 53 24 24 EMail: [email protected] Web http://www.severstal.ruCertificate No. MD00/2801/0008/1 Expiry date: 12/06/2019

As at 10 April 2018 74Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

D, E 50Normal StrengthPlatesPAO SEVERSTAL St. PetersburgA, B 70AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40

70Higher Strength

"IZHORSKIE ZAVODY"196651 Kolpino

Rolling Mill 50001, Lenina Prospect

Tel: +7 8202 53 11 46 Fax: +7 8202 53 24 24 EMail: mailto:[email protected] Web http://severstal.ruPlates with specified through thickness propertiesCertificate #: MD00/2802/0007/1 Expiry date: 12/06/2019

St Petersburg

As belowB.O.S. / Con CastSteelmakingPAO SEVERSTAL St. PetersburgAs belowE.A.F. / Con Castcarbon, carbon-manganese 315SlabsSemi-Finished

30, Mira Street162699 Cherepovets

B.O.S and E.A.F Workshops

Tel: +7 8202 53 11 46 Fax: +7 8202 53 24 24 Email: [email protected] Web http://severstal.ruCertificate #: MD00/3821/0003/1 Expiry date: 12/06/2019

Vologda Region

As belowB.O.S. / Con CastSteelmakingPJSC "Magnitogorsk Iron & Steel Works" St. Petersburgcarbon, carbon-manganese 250SlabsSemi-Finished

93, Kirova Street455000 Magnitogorsk

Steel Making and Central Laboratory

Tel +7 351 924 2214 Fax +7 351 924 5879email: [email protected] web www.mmk.ruApproval covers for slabs as detailed above to nominal width 2520mm and nominal length 7000mm.Certificate No. MD00/3103/0005/1 Expiry date: 25/08/2019

A 10Normal StrengthHot Rolled CoilPJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 10Boiler & Pressure Vessel

Rolling Mill 2000Tel +7 351 924 2214 Fax +7 351 924 5879email: [email protected] web www.mmk.ruCertificate No. MD00/3834/0003/1 Expiry date: 25/08/2019

A 25Normal StrengthPlatesPJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 25Boiler & Pressure Vessel

Rolling Mill 2350Tel +7 351 924 2214 Fax +7 351 924 5879 email: [email protected] web www.mmk.ruCertificate No. MD00/3835/0003/1 Expiry date: 25/08/2019

A 10Normal StrengthHot Rolled CoilPJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 10Boiler & Pressure Vessel

Rolling Mill 2500Tel +7 351 924 2214 Fax +7 351 924 5879email: [email protected] web www.mmk.ruCertificate No. MD00/3836/0003/1 Expiry date: 25/08/2019

A 50Normal StrengthPlatesPJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 40Boiler & Pressure Vessel

Rolling Mill 4500Tel +7 351 924 2214 Fax +7 351 924 5879 emial: [email protected] web www.mmk.ruThe approved minimum thickness is 30.0mmCertificate No. MD00/3837/0003/1 Expiry date: 25/08/2019

AH32, AH36, DH32, DH36 50Higher StrengthPlatesPJSC "Magnitogorsk Iron & Steel Works" St. Petersburg

455000, MagnitogorskRolling Mill 5000

Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: [email protected] Web http://www.mmk.ru

Certificate No. MD00/4348/0002/1 Expiry date: 24/06/2020

As at 10 April 2018 75Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Serbia

As belowB.O.S. / Con CastSteelmakingHESTEEL SERBIA IRON & STEEL D.O.O. BEOGRAD. BeogradAs below 200SlabsSemi-FinishedA, B, D 15Normal StrengthHot Rolled CoilA, B, D 15Normal StrengthPlates from coils

Radinac11300 SmederevoTel: +381 26 224 459 email: [email protected] No. MD00/0360/0009/1 Expiry date: 15/03/2019

Slovak Republic

A, B, D, E, AH32, AH36, DH32, DH36, EH32,EH36

B.O.S. / Con CastSteelmakingU.S. Steel Kosice, s.r.o. Prague

carbon, carbon-manganese 220Ingots (tonnes)Semi-FinishedA, B 12Normal StrengthPlates360AR, 410AR 12Boiler & Pressure VesselA, B, D 12Normal StrengthHot Rolled Coil360, 410, 360FG, 410FG 12Boiler & Pressure Vessel

Vstupny areal U.S. Steel044 54 KosiceTel: +42 55673 4858 Email: mailto: [email protected] Web: http:www.usske.skCertificate No. MD00/1649/0008/1 Expiry date: 16/06/2020

Semi-finished products in carbon and carbon-manganese steels in all normal strength grades and higher tensile strength grades up to EH36 with maximumdimensions 1540mm wide to 12000mm long and thickness as stated.

As belowB.O.S. / Con CastSteelmakingZELEZIARNE PODBREZOVA A.S. Praguecarbon, carbon manganese 280Blooms/BilletsSemi-Finished

Kolkáreñ 35976 81 PodbrezovaTel: +421 48 645 4040 Fax: +421 48 645 4041 email: [email protected] web: www.zelpo.sk

Certificate No. MD00/1464/0005/1 Expiry date: 03/12/2019

Slovenia

carbon, carbon-manganeseE.A.F. / Con CastSteelmakingACRONI, d.o.o. Zagrebaustenitic stainlessB.O.S/V.O.D./Con Castcarbon, carbon-manganese, austenitic stainless 250SlabsSemi-FinishedA, B, D, E 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

40Higher Strength

360AR, 410AR, 360, 410, 360FG, 410FG, 460FG,490FG, 510FG

40Boiler & Pressure Vessel

304L, 316L, 317L, 321, 347 70Austenitic Stainless

Cesta Borisa Kidrica 44SI - 4270 Jesenice

Member of Slovenian Steel Group

Tel: +385 4 584 1040 Fax: +385 4 584 1068 email: [email protected] web: http://sij.acroni.si Certificate No. MD00/1391/0009/1 Expiry date: 24/10/2019

carbon, carbon-manganese, austenitic stainlessE.A.F. / IngotSteelmakingMETAL RAVNE d.o.o. ZagrebA, B 20Normal StrengthSectionsA, B 120Normal StrengthBars

2390 Ravne na KoroškemKoroška cesta 14

Tel: +386 2 870 7200 Fax: +386 2 870 7219 Email: [email protected] Web: http://www.metalravne.comCertificate No. MD00/2889/0006/1 Expiry date: 30/05/2020

As at 10 April 2018 76Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

South Africa

As BelowB.O.S./E.A.F./Con CastSteelmakingARCELORMITTAL SOUTH AFRICA LTD. JohannesburgAs below 240SlabsSemi-FinishedB, D, E 30Normal StrengthPlatesA 50AH32, AH36, DH32, DH36, EH32, EH36, FH32,FH36

30Higher Strength

360FG, 410FG, 460FG, 490FG, 510FG 30Boiler & Pressure Vessel360AR, 410AR 40LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36

30Ferritic Low Temperature

Delfos BoulevardVanderbijlpark, 1911

Vanderbijlpark Steel

Tel +27 (0)16 889 5146 Fax +27 (0)16 889 5388 email: [email protected] web: www.arcelormittal.com

Certificate No. MD00/1404/0010/1 Expiry date: 06/05/2020

PO Box 2, Vanderbijlpark 1900

Spain

As belowE.A.F. / Con CastSteelmakingACERINOX EUROPA S.A.U. Cadiz304L, 316L, 321, 347 50Austenitic StainlessPlates304L, 316L, 321, 347 20Austenitic StainlessCoil

11379 Los BarriosCadiz

Palmones

Tel: +34 956 629421 Fax: +34 956 629311email: [email protected] web: www.acerinox.com

Certificate No. MD00/0057/0009/1 Expiry date: 14/12/2019

austenitic stainlessE.A.F. / Con CastSteelmakingACEROS INOXIDABLES OLARRA S.A. Bilbao304L, 316L, 321 100Austenitic StainlessBars

Larrabarri, 148150 Larrondo-Loiu

Tel: +34 617 464 872 Fax: +34 944 531 392email: [email protected] web: www.olarra.com

Certificate No. MD00/1753/0007/1 Expiry date: 07/09/2018

Vizcaya

As belowE.A.F/A.O.D/IngotSteelmakingACERÍA DE ALAVA, S.A. Bilbaocarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless, Ferritic StainlessSteel*, Martensitic Stainless Steel*

470BloomsSemi-Finished

carbon, carbon-manganese, alloy, austeniticstainless, duplex Stainless, Ferritic StainlessSteel*, Martensitic Stainless Steel*

470Billets

carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless, Ferritic StainlessSteel*, Martensitic Stainless Steel*

470Bars

carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless, ferritic stainless*,martensitic stainless*

360StructuralBars

01470 AmurrioAlava

(ACERALAVA)Poligono Industrial De Saratxo

Tel: +34 94 671 93 00 Fax: +34 94 672 50 62email: [email protected]

* accepted for approved applications.Approval also includes ingots in above grades up to 5 tonne.

Certificate No. MD00/0054/0007/1 Expiry date: 19/01/2019

carbon, carbon-manganeseB.O.S. / Con CastSteelmakingARCELOR MITTAL ESPAÑA Gijoncarbon, carbon-manganese 280SlabsSemi-Finished

Apartado 9033402 Avilés

Factoria de Avilés

Tel: +34 985 187299 Email: mailto:[email protected] page http://www.arcelormittal.comCertificate #: MD00/0460/0007/1 Expiry date: 29/08/2017

Asturias

As at 10 April 2018 77Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

A, B, D, E 80Normal StrengthPlatesARCELOR MITTAL ESPAÑA BilbaoFH27S, FH32, FH36, FH40 25Higher StrengthAH40, DH40, EH40 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

80

360FG, 410FG, 460FG, 490FG, 510FG 80Boiler & Pressure Vessel

Apartado 57033200 Gijón

Factoria de Gijón

Tel: +34 985 187299 Fax +34 985 187 519Email: [email protected] Web page http://www.arcelormittal.comCertificate No. MD00/1804/0013/1 Expiry date: 23/09/2017

Plates with specified through thickness properties notation Z35 may be added

As belowE.A.F. / Con CastSteelmakingCOMPAÑÍA ESPAÑOLA DE LAMINACIÓN, S.L. BarcelonaNormal Strength 180BilletsSemi-FinishedA 50Normal StrengthSectionsA 35Normal StrengthBars

Poligono Industrial 'San Vicente' s/n08755 Castellbisbal

C/ Ferralla, 12

Tel: +34 618 695 319 / +34 939 730 400 Fax: +34 93 817 6676 Email: [email protected] Web:http://www.celsa.comBillets with nominal 180mm maximum width x nominal 12000mm length to the above maximum thickness Certificate Numberr: MD00/0343/0009/1 Expiry: 20/03/2019

Barcelona

B, D 11Normal StrengthSectionsLAMINADOS LOSAL, S.A. BilbaoA 50DH32, DH36, EH32, EH36, FH32, FH36 11Higher StrengthAH32, AH36 38

Bekoibarra, 9P.O. Box 17

Tel: +34 946251400 Fax: +34 946254976 Mob: +34 68 6942188 email: [email protected] / [email protected] web: www.losal.esCertificate No. MD00/0993/0011/1 Expiry date: 18/01/2020

48300 - Gernika

As belowE.A.F. / Con CastSteelmakingMEGASIDER ZARAGOZA S.A.U. BilbaoNormal Strength, Higher Strength 130BilletsSemi-FinishedA 15Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36 15Higher StrengthA 25Normal StrengthBarsAH27S, AH32, AH36, DH27S, DH32, DH36 25Higher Strength

Parque Tecnológico de Reciclado "Lopez Soriano"Ctra. Torrecilla de Valmadrid Km 1.95

Avda. José Lopez Soriano No.100

Tel No: +34 976 466171 Fax No +34 976 517648email: [email protected] web www.megasa.comCertificate No: MD00/4183/0004/1 Expiry date 18/06/2019

B° La Cartuja Baja 50720 Zaragoza

As BelowIF/LF/V.O.D./Con CastSteelmakingRUGUI MELT S.L.U. Bilbaocarbon, carbon-manganese 165BilletsSemi-Finished

Poligono Industrial Emiliano RevillaAvenida de España, n° 21

Tel no: +34 943 85 7311 fax no: +34 943 85 7312Email: iurbieta'rugui.comWeb: www.rugui.comcertificate No: MD00/4352/0001/1 Expiry date 25/06/2017

42110 Olvega (Soria)

A 30Normal StrengthSectionsRUGUI OLVEGA S.L.U BilbaoAH32, AH36, DH32, DH36 30Higher Strength

Avenida de España No. 1,42110 Olvega (Soria),

Poligono Industrial Emiliano Revilla,

Tel: +34 943 8573 11 Fax: +34 943 85 73 12email: [email protected] www.rugui.com

Certificate No. MD00/4435/0001/1 Expiry Date: 25.02.2018

Approval is for wide flats (flat bars) up to a maximum width of 300mm.

As at 10 April 2018 78Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

A 25Normal StrengthSectionsRUGUI S.L. BilbaoAH32, AH36, DH32, DH36 40Higher Strength

Poligono Industrial Basarte20720 Azcoitia ( Guipuzcoa)

Tel: +34 943 857311 Fax: +34 943 857312 Email: mailto:[email protected] Web http://www.rugui.comThe approved sections are in the form of flat bars up to a maximum width of 200mm. Certificate No. MD00/1915/0007/1 Expiry date: 05/02/2017

Apdo. de Correos no. 8 Azpeitia ( Guipuzcoa)

As belowE.A.F. / Con CastSteelmakingSIDENOR ACEROS ESPECIALES S.L. BilbaoAs below 350BloomsSemi-Finishedcarbon, carbon-manganese, alloy 100MachineryBarsR3, R3S, R4, API-2F, R5 78Chain Cable StockU2, U3 100

Bo. Ugarte, S/NP.O. Box 76

PLANTA DE BASAURI

Tel +34 944 871 726 Fax +34 944 871826 Email: [email protected]: www.gerdau.esThe approval for bars for chain cable stock grades; R3; R3S; R4; R4S; R5 are restricted to supply to Vicinay Cadenas SA to the applicable purchasingspecification; MPR3; MPR3S; MPR4; MPR4S ;MPR5.The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval wasgranted.Certificate Number: MD00/0051/0010/1 Expiry: 21/01/2018

48970 Basauri (Vizcaya)

As belowE.A.F. / IngotSteelmakingSIDENOR ACEROS ESPECIALES S.L. BilbaoA 220Normal StrengthBarscarbon, carbon-manganese, alloy 230MachineryR3S, R4, API-2F, R4S 185Chain Cable StockR3 203R5 230

Paseo Alejandro Calonje, 139200 Reinosa (Cantabria)

PLANTA DE REINOSA

Tel: +34 942 775 288 Fax: +34 609 242 896 email: borja.lambea@gsidenor com web www.sidenor.com

Certificate Number: MD00/0546/0016/1 Expiry: 18/06/2020

The approval for bars for chain cable stock grades; R3; R3S; R4;R4S; R5 are restricted to supply to Vicinay Sestao to the applicable purchasing specification;MPR3; MPR3S; MPR4; MPR4S; MPR5.

The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval wasgranted.

The R3 bars with the diameter upto 203mm produced with con cast steel blooms manufactured at Sidenor Aceros Especials Especiales S.L. Planta De Basauri.

The R4 bars with the diameter upto 130mm produced with con cast steel blooms manufactured at Sidenor Aceros Especials Especiales S.L. Planta De Basauri.

The R5 bars with the diameter upto 175mm diameter produced with con cast steel manufactured at Aceros Especials Especiales S.L. Planta De Basauri

The R5 bars with the diameter from 175mm up to 230mm produced from ingot.

carbon, carbon-manganese, alloy 200MachineryBarsSIDENOR ACEROS ESPECIALES S.L. BilbaoR4 117Chain Cable StockR3, R3S 123R5 150U1, U2, U3 152

As at 10 April 2018 79Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

Ctra. de Zumárraga, s/n20720 Azcoitia

PLANTA DE AZKOITIA

Tel: +34 943 025206 Fax: +34 943 025299 Mob:+34 647 371 029Email: mailto:[email protected] Web:http//:www:gerdau.es

The approval for bars for chain cable stock grades; R3; R3S; R4; R5 are restricted to supply to Vicinay Sestao SA to the applicable purchasing specification;MPR3; MPR3S; MPR4, MPR5.

The bars for chain cable stock grades; R3; R3S; R4; R5 are manufactured by con-cast blooms supplieded by Sidenor Aceros Especiales S.L. Planta Basauri; or byingots supplied by Sidenor Aceros Especiales S.L. Planta Reinosa.

The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval wasgranted.

Certificate Number: MD00/0620/0013/1 Expiry: 26/03/2020

Guipúzcoa

Sweden

austenitic stainless, duplex stainlessE.A.F. / Con CastSteelmakingAB SANDVIK MATERIALS TECHNOLOGY Gothenburgaustenitic stainless, duplex stainlessE.A.F. / Ingotaustenitic stainless, duplex stainless 6Ingots (tonnes)Semi-Finishedaustenitic stainless, duplex stainless 265Bloomsaustenitic stainless, duplex Stainless 150Billetsaustenitic stainless, duplex stainless 195austenitic stainless, duplex stainless 185Barsaustenitic stainless, duplex stainless 185StructuralBarsaustenitic stainless, duplex stainless 185Machinery

SE-811 81 SandvikenTel: +46 (0) 26 263311email: [email protected] web: www.smt.sandvik.comCertificate No. MD00/2173/0007/1 Expiry date: 29/10/2018

Semi Finished products austenitic and duplex stainless steel con-cast Blooms to 365mm wide, to 7500mm long; Con-cast Billets to 150mm wide, to 6200mm long;As rolled billets to 195mm wide, to 6000mm long; semi-finished as rolled bars to 185mm diameter, 6900mm long for further processing for Rolled, ForgedProducts

As belowE.A.F. / Con CastSteelmakingOUTOKUMPU STAINLESS AB Gothenburg304L, 304LN, 316L, 321, 347 13Austenitic Stainless SteelPlates from coilsUNS S31803, UNS S32205*, UNS S32101*, UNSS32304*

8Duplex Stainless

304L, 316L, 321, 347, 304LN 13Austenitic StainlessCoilUNS S31803, UNS S32205, UNS S32101*, UNSS32304*

8Duplex Stainless

Avesta WorksBox 74

Business Area Coil EMEA

Tel: +46 (0)226 810 00 E-mail: [email protected] Web: http://www.outokumpu.com*accepted for approved applicationsCertificate No. MD00/0131/0010/1 Expiry date: 06/12/2017

SE-774 22 Avesta

1.4439 2Austenitic StainlessCoilOUTOKUMPU STAINLESS AB Gothenburg304L, 316L, 317L, 321 5UNS S32205, 1.4462, 1.4362* 2Duplex Stainless

SE-64480 TorshällaSpecial Coil Nyby

Tel +46 (0)1634 9000 Fax +46 (0)1634 9014 Email: [email protected] Web: www.outokumpu.comCertificate No. MD00/0132/0007/1 Expiry date: 29/01/2019

304L, 304LN, 316L, 316LN, 321 50Austenitic StainlessPlatesOUTOKUMPU STAINLESS AB GothenburgUNS S32304* 10Duplex StainlessUNS S32101* 20UNS S31803(MOD)* 50

As at 10 April 2018 80Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

S-693 81 Degerfors,

BA EuropeDegerfors Operations (QPE),

Tel: +46 586 47623 Mob: +46 70 6565486email: [email protected] web: www.outokumpu.com

* accepted for approved applications** Grade UNS 32304 may be accepted as equivalent to 316L as shown in LR Rules when properties meet the Rule requirements.* Avesta 2205, UNS 32205 and EN 10088-1 grade 1.4462 may be accepted as equivalent to UNS 31803 as shown in LR Rules when properties meet the Rulerequirements.

Certificate Number MD00/1754/0009/1 Expiry date: 12/11/2020

UNS S31803, UNS S32205* 200Duplex StainlessBarsOUTOKUMPU STAINLESS AB Gothenburg

SE-693 81 DegerforsDegerfors Long Products

Tel: +46 (0)586 47145 Fax: +46 (0)586 47008email: [email protected] web www.outokumpu.com

Certificate number MD00/3144/0007/1 Expiry date: 06/06/2020

* Grades UNS 32205 and EN 10088-1 grade 1.4462 may be accepted as equivalent to UNS 31803 as shown in LR Rules when properties meet the Rulerequirements.

A, B, D, E 50Normal StrengthSectionsOVAKO BAR AB. GothenburgAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

50Higher Strength

A, B, D, E 45Normal StrengthBarsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

45Higher Strength

Box 559010 Boxholm

Boxholm Works

Tel: +46 (0)240 668062 Fax: +46(0)240 668168 Mobile: +46 (0)70 3769320 Email mailto: [email protected] Web http://www.ovako.com Certificate No. MD00/0560/0010/1 Expiry date: 26/08/2020

As belowE.A.F. / Con CastSteelmakingOVAKO BAR AB. GothenburgA, B, D, E 50Normal StrengthSectionsAH32, AH36, DH32, DH36, EH32, EH36 50Higher StrengthA, B, D, E 93Normal StrengthBarsAH32, AH36, DH32, DH36, EH32, EH36 93Higher Strengthcarbon, carbon-manganese 93Machinery

Smedjebacken WorksS-777 80 SmedjebackenTel. +46 240 668000 Fax +46 (0)240 668168 email [email protected] web www.ovako.comCertificate #: MD00/0561/0007/1 Expiry date: 09/06/2019

As belowE.A.F. / IngotSteelmakingOVAKO SWEDEN AB, BU BAR Hofors-Hällefors Gothenburgcarbon, carbon-manganese, alloy 400BilletsSemi-Finishedcarbon, carbon-manganese, alloy 450Barscarbon, carbon-manganese, alloy 190StructuralBarscarbon, carbon-manganese, alloy 170MachineryU1, U2, U3, R3, R3S, R4 165Chain Cable Stock

Se-813 82 HOFORSTel: +46 (0) 298 25000 Fax: +46 0290 591606 Email: [email protected] Web: www.ovako.comCertificate No. MD00/1167/0010/1 Expiry date: 26/11/2017

Bars >75mm of grades R3, R3S and R4 supplied for mooring chain cable to Ramnas Bruk AB, Ramnas and Ljusne works. Ovako Grade 316R up to 160mmdiameter approved for R3 mooring chain.

As belowE.A.F. / IngotSteelmakingSCANA STEEL BJÖRNEBORG AB Gothenburgcarbon, carbon-manganese, alloy 75Ingots (tonnes)Semi-Finished

Kristinehamnsvägen 2S-68071 BjörneborgTel: +46 550 251 30 Fax: +46 550 269 5884email: [email protected] web: www.scana.noIngots as semi-finished products to the above maximum weight; nominal; 2070/2230mm diameter x 2600mm; are approved for further processing for forgings.Certificate Number: MD00/2769/0003/1 Expiry: 03/08/2018

As belowB.O.S. / Con CastSteelmakingSSAB EMEA AB GothenburgAs below 286SlabsSemi-FinishedA, B, D, E 75Normal StrengthPlatesFH27S 40Higher StrengthAH27S, AH32, AH36, AH40, AH42, DH27S,DH32, DH36, DH40, EH27S, EH36

60

DH42, EH32, EH40, EH42, FH32, FH36, FH40,FH42

70

AH46, AH50, AH55, AH62, AH69, DH46, DH50,DH55, DH62, DH69, EH46, EH50, EH55, EH62,

80

As at 10 April 2018 81Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

SwedenEH69, FH46, FH50, FH55, FH62, FH69 80Higher StrengthPlates460FG, 490FG, 510FG 60Boiler & Pressure Vessel360FG, 410FG 75LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36, LTFH40

40Ferritic Low Temperature

S-61380 OxelösundOXELÖSUND

Tel: +46 155 25 58 10

E-mail: [email protected]

Website: www.ssab.com

All plates with specified through thickness properties.Semi-finished products in carbon and carbon-manganese steel with fine grain (element combinations as stated), slabs to 1680 mm wide, to 11000mm long ofmaximum weight 30T for further processing to rolled products

Materials Quality Scheme Approved - Approval No. MQS 049

Certificate No. MD00/1282/0012/1 Expiry date: 23/04/2020

Taiwan, Republic of China

As belowB.O.S. / Con CastSteelmakingCHINA STEEL CORPORATION KaohsiungNormal strength, Higher Strength 270SlabsSemi-FinishedA, B, D, E 50Normal StrengthPlatesAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40, EH47

75Higher Strength

360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50

No.1 Chung Kang RoadHsiao Kang

Tel: +886 7 802 1111 ext 2208 Fax: +886 7 805 1292Email: [email protected] page: www.csc.com.tw All grades are approved with specified with through thickness properties.Certificate No. MD00/0304/00013/1 Expiry date: 02/07/2020

Kaohsiung

As belowE.A.F. / Con CastSteelmakingDRAGON STEEL CORPORATION KaohsiungAH32, AH36, DH32, DH36 26Higher StrengthSections

Longjing Dist.,Taichung City

100, Longchang Road,

Tel: +886 4 2630 6088 Ext. 8705 Fax: +886 4 2630 6041 Email:[email protected] www.dragonsteel.com.twBillets / Blooms as semi-finished products to the above maximum thickness x nominal 750mm maximum width x nominal 12000mm maximum length Sections produced are H beam sections to the above maximum thickness x 900mm x 300mm overall dimensions x nominal 19000mm maximum length.Certificate Number: MD00/3768/0005/1 Expiry: 01/04/2019

A 15Normal StrengthSectionsT. S. STEEL COMPANY LTD. KaohsiungAH32, AH36 12Higher StrengthA 25Normal StrengthBars

Tsuang-Hine Industrial ZoneHsen-Kang Road

No.6 Kon-Sixth Road

Tel: +886 4 798 0060 Fax: +886 4 799 1522email: [email protected]

Certificate No. MD00/2313/0007/1 Expiry date: 09/04/2017

Chang-Hua Hsien

As belowE.A.F. / Con CastSteelmakingTUNG HO STEEL ENTERPRISE CORP. Taipeicarbon, carbon manganese, Normal Strength,Higher Strength

430Blooms/BilletsSemi-Finished

No.22, Pingding Erhu Village,Sihu Township,

Miao Li Works

Tel: +88 637 923333 ext197 Fax: +88 637 922994 Email mailto:[email protected] Web http://www.tunghosteel.comCertifcate Number: MD00/3719/0004/1 Expiry date: 15/12/2018

Miaoli County 36842,

As at 10 April 2018 82Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

A 18Normal StrengthSectionsTUNG HO STEEL ENTERPRISE CORP. TaipeiAH27S, AH32, AH36 18Higher Strength

No. 8, Jiaxing Street,Xiaogang Dist.

Kaohsiung Works

Tel: +88 6 7802 3131 Fax: +88 6 801 0696 Email: [email protected] Web http://www.tunghosteel.comCertificate Number: MD00/3720/0004/1 Expiry: 14/12/2018

Kaohsiung City, 81257

austenitic stainless, duplex stainlessE.A.F. / Con CastSteelmakingWALSIN LIHWA CORP. Kaohsiungaustenitic stainless, duplex stainless 200SlabsSemi-Finishedaustenitic stainless, duplex stainless 240Billets

Chin Shuei LiYenshui District

Yenshui PlantNo. 3-10, Shi Jou Liau

Tel +886 (0)6 6520911 ext. 5802 Fax +886 (0)6 6520933 Email mailto:[email protected] Web http://www.walsin.comCertificate No. MD00/3063/0005/1 Expiry date: 14/03/2019

Semi Finished Products Austentic & Duplex Stainless slabs to 1300mm wide, to 12000mm long; square billets to 155mm wide, 12000mm long; round billets withmaximum diameter 240mm , to 12000mm long

Tainan City 73743

Thailand

A 50Normal StrengthPlatesLPN PLATE MILL PUBLIC COMPANY LIMITED Bangkok

Pakklong BangplakodPrasamutjedee

199/9 Moo 4 Suksawad Road

Tel: +66 2815 6400-9 Fax: +66 2815 6415 Email: [email protected]: www.lpnpm.co.thCertificate No. MD00/2578/0008/1 Expiry date: 31/08/2020

Samutprakarn 10290

A 40Normal StrengthPlatesSAHAVIRIYA PLATE MILL PUBLIC COMPANYLIMITED

Bangkok

160 Moo 14 Sukhumvit RoadBangpakong

Chachoengsao

Tel: +66 38883 2056 60 Fax: +66 3853 1635 Email: [email protected]: www.spm-plate.comCertificate No. MD00/3952/0003/1 Expiry date: 31/08/2020

Chachoengsao 24130

B, D 8Normal StrengthHot Rolled CoilSAHAVIRIYA STEEL INDUSTRIES PUBLICCOMPANY LIMITED

Bangkok

A 19

360AR, 410AR 19Boiler & Pressure Vessel

9M.7 Tumbol MearumphuengAmphur Bang Saphan

Prachuab Kirikhan

Tel: (+66) 32 691403 Fax: (+66) 32 691408 Email mailto: [email protected] Web http://www.ssi-steel.comCertificate No. MD00/3764/0003/1 Expiry date: 22/09/2018

Prachuab Kirikhan 77140

As at 10 April 2018 83Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

The Netherlands

As belowE.A.F. / IngotSteelmakingNEDSTAAL B.V. Haren(Groningen)

carbon, carbon-manganese, alloy 11Ingots (tonnes)Semi-Finished

carbon, carbon-manganese, alloy 320Slabs

carbon, carbon-manganese, alloy 400Blooms

carbon, carbon-manganese, alloy 185Billets

Rapenburg 1NL 2952 AP

Tel: +33 (0) 78 692 3700 Fax: +31 (0) 78 692 3712 Email mailto:[email protected] & [email protected] Web: http://www.nedstaal.nlThe above semi finished products to the indicated maximum weight/ thickness are approved for further reprocessing for forgings; ingots nominal maximumdimensions 940mm x 780mm x 2300mm long; slabs nominal 620mm wide x nominal 3300mm long; billets nominal 185mm wide x 9200mm long; bloomsnominal 220mm wide x 13100mm long.Certificate Number: MD00/3010/0005/1 Expiry: 10/09/2018

Alblasserdam

As belowB.O.S. / Con CastSteelmakingTATA STEEL IJMUIDEN B.V Haren(Groningen)

carbon, carbon-manganese 225SlabsSemi-Finished

A, B 20Normal StrengthPlates

A, B 20Normal StrengthHot Rolled Coil

Postbus 100001970 CA IJmuiden

IJmuiden Works

Tel +31 2514 92110 Fax +31 2514 70414 Email: [email protected]: www.tatasteel.nlCertificate No. MD00/0698/0009/1 Expiry date: 28/09/2018

Tunisia

A 25Normal StrengthFabricated SectionsPALESCANDOLO CNT sarl GenoaAH32, AH36 25Higher Strength

Parc D' Activite' Economique De Bizerte7000 BizerteTel: + 21 77 241 7292 Fax: +21 77 241 7552 Email: [email protected] Certificate Number: MD00/4018/0002/1 Expiry: 25/04/2018

Turkey

As belowE.A.F./Ingot/Con CastSteelmakingASIL CELIK SANAYI VE TICARET A.S. Istanbulcarbon-manganese, alloy 1Ingots (tonnes)Semi-Finishedcarbon 2carbon, carbon-manganese, alloy 600Blooms/Billetscarbon, carbon-manganese, alloy 300StructuralBarscarbon, carbon-manganese, alloy 240Machinery

Gemic Koyu Mevki 16800Orhangazi, BursaTel: +90 224 280 62 60 Fax: +90 224 280 62 00 email [email protected] web www.asilcelik.com.trCertificate No. MD00/1921/0007/1 Expiry date: 03/05/2019Machinery bars approved to 220mm diameter from ingot route, and to 240mm diamter from concast route.

As belowB.O.S. / Con CastSteelmakingEREGLI DEMIR VE CELIK FABRIKALARI T.A.S. IstanbulA, B, D, E 60Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36

60Higher Strength

360FG, 410FG, 460FG, 490FG, 510FG 60Boiler & Pressure VesselA, B, D, E 15Normal StrengthHot Rolled CoilAH32, AH36, DH32, DH36, EH27S, EH32, EH36,FH27S, FH32, FH36

15Higher Strength

360FG, 410FG, 460FG, 490FG, 510FG 15Boiler & Pressure Vessel

As at 10 April 2018 84Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

KDZ. Eregli67330

Tel: +90 (0)372 329 3838 Fax: +90 (0)372 323 2598 email: [email protected] web: www.erdemir.com.tr

Certificate No. MD00/1951/0011/1 Expiry date: 04/05/2020

Zonguldak

As belowE.A.F. / Con CastSteelmakingÖZKAN DEMIR ÇELIK SANAYI A.S. Istanbulcarbon, carbon manganese 260Blooms/BilletsSemi-FinishedD, E 12Normal StrengthSectionsA, B 25AH40, DH40 19Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

28

Bozköy Köyü13. Cadde N:4 35800

Tel +90 232 625 1515 Fax +90 232 625 1054email: [email protected] web: www.ozkansteel.comCertificate No. MD00/2984/0006/1 Expiry date: 25/03/2020

Aliaga-Izmir

Ukraine

As belowE.A.F. / Con CastSteelmakingLIMITED LIABILITY COMPANY METALLURGICALPLANT DNEPROSTEEL

Mykolaiv

carbon, carbon-manganese, alloy 470BarsSemi-Finished

4 Vynokurova Street,49051 Dnipro

DNEPROSTEEL

Tel: +38 067 637 36 48 Fax: +38 056 747 40 40Email: Dmitriy. [email protected]: www.interpipe.bizCertificate No. MD00/4711/0001/1, Expiry date: 07/08/2020

As belowB.O.S./Ingot/Con CastSteelmakingPJSC "ALCHEVSK IRON & STEEL WORKS" MykolaivNormal strength, Higher Strength 300SlabsSemi-FinishedD, E 45Normal StrengthPlatesB 50A 72AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

50Higher Strength

360AR, 410AR 22Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50360, 410 72A 8Normal StrengthSectionsA 100Normal StrengthBars

Severodonetsk,Lugansk Region,

20A, Vylesova Str.,

Tel: +38 06442 73382email: [email protected] No: MD00/4588/0001/1 Expiry Date: 26/01/2018

93400

As belowB.O.S. / Con CastSteelmakingPJSC "AZOVSTAL IRON & STEEL WORKS" MykolaivNormal strength, Higher Strength 270SlabsSemi-FinishedD, E 50Normal StrengthPlatesA, B 100AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40

50Higher Strength

360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 50Boiler & Pressure Vessel

1, Leporsky St.Mariupol 87500Tel: +38 0629 46 8501

E-mail: [email protected]

Website: www.azovstal.metinvestholding.com

Certificate No. MD00/0779/0010/1 Expiry date: 13/02/2021

Including plates with specified through thickness properties. Z35 may be applied to all grades and thicknesses

As at 10 April 2018 85Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

As belowE.A.F. / IngotSteelmakingPJSC "ENERGOMASHSPETSSTAL" Mykolaivcarbon, carbon-manganese, alloy 250Ingots (tonnes)Semi-Finished

Donetsk Region84306 Kramatorsk

Tel: +38 (06264) 6-94-93 Fax: +38 (06264) 6-94-93Email: [email protected] No. MD00/3575/0002/1 Expiry date: 15/03/2018

As belowB.O.S. / Con CastSteelmakingPJSC "ILYICH IRON AND STEEL WORKS OFMARIUPOL"

Mykolaiv

A, B, D, E 50Normal StrengthPlates

DH40, EH40 25Higher Strength

AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

50

360AR, 410AR, 460AR 25Boiler & Pressure Vessel

360FG, 410FG 50

1 Levchenko StreetMariupol 87504All grades and thicknesses with specified through thickness properties. Notation Z25 or Z35 may be added.

Tel: +38 (0)0 629 56 49 79

E-mail: [email protected]

Website: www.ilyichsteel.metinvestholding.com

Certificate No. MD00/0775/0007/1 Expiry date: 01/07/2019

As belowE.A.F. / IngotSteelmakingPJSC ELEKTROMETALLURGICAL WORKSDNIPROSPETSSTAL

Mykolaiv

304L, 316L, 321 270Austenitic StainlessBars

carbon, carbon-manganese, alloy 300Machinery

U1, U2, U3 85Chain Cable Stock

81 Yuzhnoye ShosseZaporozhye, 69008

named after A.N. Kuzmin

Tel: +38 612 283 4062 email : [email protected] web www.dss.com.uaIncluding forged bars and tube blanks (billets) in all above qualities.Certificate No. MD00/2225/0008/1 Expiry date: 02/07/2019

United Kingdom

A 50Normal StrengthSectionsACENTA HOT ROLLED BirminghamAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

32Higher Strength

A 50Normal StrengthBarsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

50Higher Strength

Peartree LaneWoodside, Dudley

Tel: +44 (0) 1384 471 200 Email: mailto:[email protected] Web: http://www.acentasteel.comCertificate Number: MD00/2618/0008/1 Expiry: 19/02/2019

West Midlands DY2 0QS

A, B, D, E 77Normal StrengthSectionsBRITISH STEEL BirminghamAH27S, AH32, AH36, DH27S, DH32, DH36 77Higher Strength

MiddlesboroughTS6 7RP

LACKENBY WORKS

Tel: +44 (0)1642 402789

E-mail: [email protected]

Website: www.britishsteel.co.uk

Materials Quality Scheme Approved - Approval No. MQS031

Certificate No: MD00/0242/0017/1 Expiry date: 31/05/2020

As at 10 April 2018 86Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

A, B, D, E 20Normal StrengthSectionsBRITISH STEEL BirminghamAH40, DH40 15Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 20

P.O. Box 1Saltburn by the Sea

SPECIAL PROFILES, SKINNINGROVE

Tel: +44 (0)1724 402789

E-mail: [email protected]

Materials Quality Scheme Approved - Approval No. MQS032

Certificate #: MD00/0243/0014/1 Expiry date: 17/08/2020

TS13 4ET

As belowB.O.S. / Con CastSteelmakingBRITISH STEEL Hullcarbon, carbon-manganese 305SlabsSemi-Finishedcarbon 355Blooms/BilletsB, D, E 50Normal StrengthPlatesA 80FH40, FH42, FH46 25Higher StrengthAH40, AH42, AH46, DH40, DH42, DH46, EH40,EH42, EH46

30

FH32, FH36 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

70

360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 70360, 410 80LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40

30Ferritic Low Temperature

A, B, D, E 50Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

50Higher Strength

Brigg Road,Scunthorpe.

SCUNTHORPE

Tel: + 44 (0) 1724 402789 Fax: +44 (0) 1724 402936

E-mail: [email protected]

Website: britishsteel.co.uk

Materials Quality Scheme Approved - Approval No. 029.

Certificate No. MD00/4619/0002/1 Expiry Date: 09/07/2017

North Lincolnshire DN16 1BP

AH32, AH36, DH32 18Higher StrengthFabricated SectionsCELLBEAM LTD. LiverpoolDH36 30EH46-TM 20High Strength

Thorp Arch Trading Estate Wetherby

Tel: +44 (0)1737 840600 Email: [email protected] Web: www.cellbeam.co.ukCertificate No. MD00/3534/0006/1 Expiry date: 09/11/2020

West Yorkshire LS23 7DB

As belowE.A.F. / Con CastSteelmakingCELSA MANUFACTURING (UK) LTD. SouthamptonNormal Strength 140Blooms/BilletsSemi-FinishedA 25Normal StrengthSections

Seawall Road,Tremorfa,

Sections MillTremorfa Works

Tel: +44 (0) 2920 351899 Fax: +44 (0) 2920 351868

E-mail: [email protected]

Website: www.celsauk.com

Certificate No. MD00/3552/0004/1 Expiry date: 15/12/2017

Concast blooms/billets covers billets to 140mm x140mm and concast 'mini slabs' to 280 x 120mm.

Cardiff. CF24 5TH

As at 10 April 2018 87Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

A, B, D, E 12Normal StrengthSectionsLIBERTY MERCHANT BAR PLC. LiverpoolAH32, AH36, DH32, DH36 12Higher StrengthA, B, D, E 50Normal StrengthBarsAH32, AH36, DH32, DH36 50Higher Strength

Scunthorpe Steel WorksBrigg Road,

Liberty House

Tel +44 (0)1724 403094

E-mail: [email protected]

Website: www.liberty.com

The approved sections include flat bar and angled bar

Certificate No. MD00/1599/0011/1 Expiry date: 25/11/2018

Scunthorpe. North Lincolnshire. DN16 1XL

E 50Normal StrengthPlatesLIBERTY STEEL DALZELL LIMITED GlasgowA, B, D 100FH32, FH36 30Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 75

Motherwell ML1 1PUTel: +44 (0)1698 900331

Email to: [email protected]

Website: www.libertyhousegroup.com

Certificate No. MD00/0235/0013/1 Expiry date: 17/05/2020

As belowB.O.S./Ingot/Con CastSteelmakingLIBERTY STEEL DALZELL LIMITED Liverpoolcarbon, carbon-manganese 305SlabsSemi-Finishedcarbon, carbon-manganese 355Blooms/BilletsE 50Normal StrengthPlatesB, D 60A 80FH40, FH42, FH46 25Higher StrengthAH40, AH42, AH46, DH40, DH42, DH46, EH40,EH42, EH46

30

FH32, FH36 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

70

360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 70360, 410 80LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40

30Ferritic Low Temperature

A, B, D, E 50Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

50Higher Strength

P.O. Box 1Scunthorpe DN16 1BP

Scunthorpe

Tel: +44 1724 404040 Email:maito: [email protected]

Web:http://www.tatasteel.com

All plates with through thickness properties.

Materials Quality Scheme Approved - Approval No. MQS029

Certificate #: MD00/0240/0015/1 Expiry date: 22/07/2017

stainless steelE.A.F/A.O.D/L.A.F/ConCastSteelmakingOUTOKUMPU STAINLESS LTD. Liverpoolstainless steel 19Ingots (tonnes)Semi-Finishedstainless steel 300Slabsstainless steel 300Bloomsstainless steel 200Billets

As at 10 April 2018 88Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

P.O. Box 161Europa Link

LONG PRODUCTS, SMACC

The approval for steelmaking and ingots, slabs, blooms and billets in stainless steel covers the supply of austenitic, duplex, ferritic, martensitic and precipitationhardening grades, in accordance with the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3 or appropriate international ornational standards. The final processing mill is responsible for ordering steel which complies with their surface and internal quality standards and approvedchemical composition to enables them to achieve the required physical and mechanical properties.

Mass of slab and bloom up to 30.0T.and billet up to 20T

Tel: +44 (0)114 2616292 Mob: +44 7947 255428email: [email protected] web: www.outokumpu.comCertificate No. MD00/1883/0009/1 Expiry date: 31/12/2019

Sheffield, S9 1TZ

As belowB.O.S. / Con CastSteelmakingSAHAVIRIYA STEEL INDUSTRIES UK Liverpoolcarbon, carbon-manganese 305SlabsSemi-Finished

Steel HouseRedcar

Tel: +44 01642 408053 Email: [email protected] Web: http://www.ssi-steel.co.uk Certificate No. MD00/4057/0002/1 Expiry date: 21/07/2018

TS10 5QW

carbon, carbon-manganese, alloy, austeniticstainless

E.A.F. / IngotSteelmakingSHEFFIELD FORGEMASTERS INTERNATIONALLTD.

Birmingham

Brightside LaneSheffield S9 2RW

P.O. Box 286

Tel: +44 (0)114 244 9071 Fax: +44 (0)114 2519021 Email: [email protected]

Website: www.sheffieldforgemasters.com

Certificate No. MD00/0524/0009/1 Expiry date: 29/06/2020

A 20Normal StrengthSectionsTATA STEEL UK LIMITED BirminghamAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

20Higher Strength

carbon, carbon-manganese 20Structural SectionsFabricated Sections

Brenda RoadHartlepool

Hartlepool Works20 Inch H.F.I. Pipe Mill

Tel: +44 (0)1429 527249 Mob: +44 (0)7743 842969 Email: mailto:[email protected] Web:http://www.tatasteeleurope.com

Certificate #: MD00/0236/0008/1 Expiry date: 09/09/2017

Teeside TS25 2EG

carbon, carbon-manganese, alloyE.A.F./Ingot/Con CastSteelmakingTATA STEEL UK LIMITED BirminghamAs below 13Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese, alloy 381Semi-finished ProductsBarscarbon, carbon-manganese, alloy 300MachineryU1, U2, U3, R3, R3S, R4 165Chain Cable Stock

StocksbridgeSheffield

Rotherham & Stocksbridge Sites

Tel: +44 (0)114 283 2000 email [email protected] web: www.tatasteelspeciality.com

Certificate No. MD00/1593/0007/1 Expiry date: 03/07/2017

South Yorkshire S36 2JA

As belowB.O.S. / Con CastSteelmakingTATA STEEL UK LIMITED Birminghamcarbon, carbon-manganese 238SlabsSemi-Finished

Port TalbotSA13 2NG

Port Talbot Works

Tel: +44 (0) 1639 872168 Fax: +44 (0) 1698 266100 Ext. 394 Web page http:\\www.tatasteeleurope.com

Approval covers concast slabs to nominal size 1850mm wide x 10,000mm long to the maximum thickness for further processing to rolled products.

Certificate No.: MD00/3909/0002/1 Expiry Date: 28.04.2017

carbon, carbon-manganese 16Structural SectionsFabricated SectionsTATA STEEL UK LIMITED Birmingham

As at 10 April 2018 89Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

CorbyNorthamptonshire

Corby WorksP.O.Box 101, Weldon Road

Tel: +44 (0)1536 404704 Fax: +44 (0)1536 404212 Email: [email protected] Web: http://www.tatasteel.comIncludes fabricated hollow sectionsCertificate No. MD00/0234/0002/1 Expiry date: 25/02/2018

NN17 5UA

United States of America

As belowB.O.S. / Con CastSteelmakingARCELORMITTAL BURNS HARBOR ChicagoD 35Normal StrengthPlatesA, B 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36

75Higher Strength

Burns HarborIN 46304-9745

250 West Highway 12

Tel: +1 219 787 2854 Fax: +1 219 787 2139email [email protected] web: www.arcelormittal.com Certificate Number: MD00/2331/0007/1 Expiry: 16/12/2018

carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingELLWOOD QUALITY STEEL COMPANY Philadelphiacarbon, carbon-manganese, alloy 77Ingots (tonnes)Semi-Finished

700 Moravia StreetNew Castle

Tel: +1 724 658 6849 Fax: +1 724 658 6802Email mailto:[email protected]: www.egi.orgCertificate No. MD00/2652/0006/1 Expiry date: 14/02/2018

Pennsylvania 16101

A, B, D 50Normal StrengthPlatesEVRAZ OREGON STEEL MILLS SeattleAH27S, AH32, AH36, DH27S, DH32, DH36 30Higher Strength360AR, 410AR, 360FG, 410FG 50Boiler & Pressure VesselA, B, D 19Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 19Higher Strength

14400 N. Rivergate Blvd.Portland

Tel: +1 503 978 6130 Fax: +1 503 978 4975Email: mailto:[email protected] Web http://www.evrazincna.comIncluding normal strength grades with specified through thickness properties (Z35)

MATERIALS QUALITY SCHEME APPROVED - MQS 047Certificate No. MD00/1152/0007/1 Expiry date: 31/05/2018

OR 97203

E 51Normal StrengthPlatesJSW STEEL (USA) INC. HoustonA, B, D 102AH27S, AH32, AH36, DH27S, DH32, DH36,DH40

102Higher Strength

360FG, 410FG, 460FG, 490FG, 510FG 102Boiler & Pressure Vessel

5200 East McKinney RoadBaytown

Tel: +1 281 382 5121 email [email protected] web: www.jswsteel.us

Certificate No. MD00/3505/0004/1 Expiry date: 24/08/2020

Texas 77523

A, B, D 51Normal StrengthPlatesNUCOR STEEL - HERTFORD COUNTY Norfolk,VAAH32, AH36, DH32, DH36 51Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 51Boiler & Pressure Vessel

CofieldNorth Carolina

1505 River Road

Tel: +1 252 356 3712 E-mail: [email protected] Website: www.nucorhertford.com

Certificate No. MD00/4593/0001/1 Expiry date: 06/07/2019

27922

As belowE.A.F. / Con CastSteelmakingNUCOR STEEL MEMPHIS, INC New OrleansCarbon, Carbon-manganese, Alloy 203Rolled Round BarsSemi-FinishedCarbon, Carbon-manganese, Alloy 511As Cast Round SectionCarbon, Carbon-manganese, Alloy 254Rolled Square Bars

As at 10 April 2018 90Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

MemphisTN 38109

3601 Paul R. Lowry Road

Tel: +1 901 786 5416 Fax: +1 901 788 5300 Email: [email protected] Web http://www.nucor.com

Certificate No. MD00/4059/0001/1 Expiry date: 22/07/2015

As belowE.A.F. / Con CastSteelmakingNUCOR STEEL TUSCALOOSA INC. HoustonA 20Normal StrengthHot Rolled Coil360FG, 410FG 20Boiler & Pressure VesselA 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 13Higher Strength

TuscaloosaAL 35404-1000

1700 Holt Road N.E.

Tel: +1 205 562 1200 Fax: +1 205 556 1482 Email to: [email protected] Web http://www.nucor.com

Materials Quality Scheme approved - MQS048

Certificate No. MD00/3323/0005/1 Expiry date: 04/08/2018

As belowE.A.F./Ingot/Con CastSteelmakingREPUBLIC STEEL Chicagocarbon, carbon-manganese, alloy 14Ingots (tonnes)Semi-Finishedcarbon, carbon-manganese 330Bloomscarbon, carbon-manganese 178Billets

2633 Eighth Street N.E.Canton

HOT ROLLED BAR DIVISIONCANTON WORKS

Tel: +1 330 438 5543 Fax: +1 330 438 5552 Email to: [email protected] Web: http://www.republicsteel.comIngots as semi finished products, nominal 740mm diameter x 4800mm, are approved for further processing for forgings to the maximum un-cropped weightshown above.Certificate #: MD00/2236/0006/1 Expiry date: 14/05/2016

Ohio 44704-2311

As belowE.A.F. / Con CastSteelmakingSSAB ALABAMA, INC. New OrleansD 35Normal StrengthPlatesA, B 50AH27S, AH32, AH36, DH32, DH36 38Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 38Boiler & Pressure Vessel

AxisAlabama 36050

12400 Highway 43 North

Tel: + 01 251 - 6624524

E-mail: [email protected]

Website: www.SSAB.com

Materials Quality Scheme Approved - MQS 042

Certificate No. MD00/3108/0008/1 Expiry date: 29/03/2020

carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingSTEEL DYNAMICS INC ClevelandCarbon, Carbon manganese, Alloy 178Rolled BarsSemi-Finished

8000 North County Road 225 East,Pittsboro,

ENGINEERED BAR PRODUCTS DIVISION

Tel: +1 317 892 7179 Fax: +1 317 892 7005

E-mail: [email protected]

Certificate No: MD00/4134/0002/1 Expiry Date: 23/03/2019

Concast blooms approved to 262 x 358 mm section.

IN, 46167

As belowE.A.F. / Con CastSteelmakingSTEEL OF WEST VIRGINIA, INC. PhiladelphiaA, B, D 12Normal StrengthSectionsAH32, AH36 12Higher Strength

As at 10 April 2018 91Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct

List 1Approved Steelmakers and Manufacturers of

Rolled Steel Plates, Strip, Sections & Bars

LR Office

17th Street and 2nd Avenue,Huntington,

Tel: 800-828-6849 Fax: +1 304-697-5842 Mob: +1 304-638-7981

email: [email protected] web: swvainc.com

Approved for bulb flats

Materials Quality Scheme Approved - Approval No. MQS 059

Cert No: MD00/4547/0001/1 Expiry Date: 31/01/2019

WV 25703

As belowE.A.F./Ingot/Con CastSteelmakingTIMKEN STEEL CORPORATION Chicagocarbon, carbon-manganese, alloy 330BarsSemi-Finished

CantonOH 44706-0932

Faircrest Steel Plant1835 Dueber Avenue S.W.

Tel: +1 330 471 3263 Fax: +1 330 471 4077 Email: [email protected] Werb: http://www.timken.com

Certificate No. MD00/1510/0008/1 Expiry date: 10/01/2020

As belowE.A.F. / Con CastSteelmakingTIMKEN STEEL CORPORATION Chicagocarbon, carbon-manganese, alloy 330BarsSemi-Finished

1835 Dueber Avenue S.W.Canton

Harrison Steel Plant

Tel: +1 330 471 3263 Fax: +1 330 471 4077 Email: [email protected] Werb: http://www.timken.com

Certificate No. MD00/4284/0004/1 Expiry date: 10/01/2020

OH 44706-0932

As at 10 April 2018 92Page

In the event of any conflict or ambiguity between this printout and the original electronic document, the electronic document shall prevail.

© Lloyd’s Register Group Limited 2018. All rights reserved.

Lloyd's Register Group Limited, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as ‘Lloyd's Register’. Lloyd's Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd's Register entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract. © Lloyd’s Register Group Limited 2018. All rights reserved.