api monogram program: definition of a...

31
API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3 FIRST EDITION, XXXXXX 2015

Upload: dangthien

Post on 22-Mar-2018

321 views

Category:

Documents


16 download

TRANSCRIPT

Page 1: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3 FIRST EDITION, XXXXXX 2015

Page 2: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

i

Special Notes

API publications necessarily address problems of a general nature. With respect to particular circumstances, local, state, and federal laws and regulations should be reviewed.

Neither API nor any of API's employees, subcontractors, consultants, committees, or other assignees make any warranty or representation, either express or implied, with respect to the accuracy, completeness, or usefulness of the information contained herein, or assume any liability or responsibility for any use, or the results of such use, of any information or process disclosed in this publication. Neither API nor any of API's employees, subcontractors, consultants, or other assignees represent that use of this publication would not infringe upon privately owned rights.

API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure the accuracy and reliability of the data contained in them; however, the Institute makes no representation, warranty, or guarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or damage resulting from its use or for the violation of any authorities having jurisdiction with which this publication may conflict.

API publications are published to facilitate the broad availability of proven, sound engineering and operating practices. These publications are not intended to obviate the need for applying sound engineering judgment regarding when and where these publications should be utilized. The formulation and publication of API publications is not intended in any way to inhibit anyone from using any other practices.

Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standard is solely responsible for complying with all the applicable requirements of that standard. API does not represent, warrant, or guarantee that such products do in fact conform to the applicable API standard.

All rights reserved. No part of this work may be reproduced, translated, stored in a retrieval system, or transmitted by

any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the

publisher. Contact the Publisher, API Publishing Services, 1220 L Street, NW, Washington, DC 20005.

Copyright © 2015 American Petroleum Institute

Page 3: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

i

Foreword

Nothing contained in any API publication is to be construed as granting any right, by implication or otherwise,

for the manufacture, sale, or use of any method, apparatus, or product covered by letters patent. Neither

should anything contained in the publication be construed as insuring anyone against liability for

infringement of letters patent.

This document was produced under API standardization procedures that ensure appropriate notification and

participation in the developmental process and is designated as an API standard. Questions concerning the

interpretation of the content of this publication or comments and questions concerning the procedures under

which this publication was developed should be directed in writing to the Director of Standards, American

Petroleum Institute, 1220 L Street, NW, Washington, DC 20005. Requests for permission to reproduce or

translate all or any part of the material published herein should also be addressed to the director.

Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years. A

one-time extension of up to two years may be added to this review cycle. Status of the publication can be

ascertained from the API Standards Department, telephone (202) 682-8000. A catalog of API publications

and materials is published annually by API, 1220 L Street, NW, Washington, DC 20005.

Suggested revisions are invited and should be submitted to the Standards Department, API, 1220 L Street,

NW, Washington, DC 20005, [email protected].

Page 4: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

ii

Table of Contents [to be added upon publication]

Page 5: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

1

1 Scope The API Monogram Program is a voluntary licensing program designed to facilitate the consistent manufacturing of product that conforms to API standards. In order to assure that only qualified and competent organizations possess the API monogram license, licensees provide a statement of their capabilities both during the application process and whenever changes to those capabilities occur. The program requires that manufacturers maintain these capabilities, including the resources, processes and technology, to manufacture products that fall within the scope of licensing. These capabilities are verified during on the site audits. The program gives licensed manufacturers the opportunity to mark conforming product with the API Monogram so that it is easily recognizable and identifiable in the field. The licensee must implement, maintain, and continually improve their quality management system to meet the oil and gas industry’s quality management system specification, API Spec Q1. The API Monogram Licenses are issued only after an on-site audit has verified that the facility meets program requirements. Licensees are required to maintain continued management system conformity to API Spec Q1 as well as the product standard and program requirements. In order for a license to remain active, the licensee must go through a renewal audit after each 3 year period. All licensees, licensing information and licensing statuses are identified on the API Composite list, an on-line directory. The program requirements and obligations, including the use of the mark, reporting on nonconforming equipment, QMS conformity with API Spec Q1, and product conformity with the product specification, are enforced through a legally binding agreement between API and the Licensee. The scope of this technical report is to provide the definition of a “manufacturer” as applicable to the API Monogram program. This is accomplished by establishing categories of licensees. The categories are based on the activities needed to produce the product within the scope of their applicable API Licenses. In the development of the categories, considerations were given to the various processes needed for production, the types and criticality of the products produced, and the technical requirements contained in the applicable API product standards. In order to more clearly define the eligibility requirements for receiving monogram licensing, this technical report identifies the key manufacturing and/or production activities that are to be performed by licensees at the licensed addresses (on-site) or at facilities related to the licensed organizations (off-site). These minimum activities shall not be outsourced. In the determination of the minimum activities that must be performed by the licensed organization, consideration was given to the extent of the controls needed by the licensed organization to assure that monogrammed products identified in the API Licensing Information Forms were produced in accordance with the API Monogram license agreement, under a quality management system conforming to API Specification Q1 and in full conformance to the applicable API Product standards. Annex A provides a matrix for easier navigation through this Technical Report. The annex identifies the API Product specification, the monogrammable equipment contained within each specification, the corresponding activities table, and the page location of each table.

2 Normative References The following referenced documents are indispensable for the application of this document. Licensees need to have access to the API Product Specifications that are applicable to the scope of their API License(s). For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. API Specification Q1, Specification for Quality Management System Requirements for Manufacturing Organizations for the Petroleum and Natural Gas Industry

Page 6: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

2

3 Terms, Definitions, Acronyms, and Abbreviations

3.1 Terms and Definitions For the purposes of this technical report, the following definitions apply: 3.1.1 alternative marking agreement AMA Contractual arrangement between an API Licensee and a Marking Party to allow the API Monogram to be applied by a party other than the original API Licensee, or at a facility not identified on the original API License. NOTE The marking party obtains an API Monogram Alternative Marking Agreement prior to marking any product with the API Monogram.

3.1.2 API advisory 6 Formal notice issued by API that allows licensees to exclude design and development from the scope of their quality management systems for specified products where all necessary design criteria are provided by the applicable API product specification 3.1.3 API monogram Licensed API trademark used to represent and warrantee by the licensed manufacturer that, on the date of manufacture, the product conforms to all applicable, current editions of the applicable API Product Specification requirements and has been manufactured within a quality management system that meets API Q1 3.1.4 assembly (verb) Association of multiple components into a sub-assembly or finished product 3.1.5 demonstrated capability Objective evidence that an organization has the facilities, resources, technology, processes, and competent personnel to perform the activities, under controlled conditions, needed to produce products (including services or processes) which conform to established requirements 3.1.6 final acceptance testing Testing performed on product as required by the applicable product specification, excluding nondestructive examination (NDE) or dimensional verification. 3.1.7 in-process Inspection Inspection activities, excluding nondestructive examination (NDE), performed on products as required by the applicable product specification, the manufacturer or customer 3.1.8 monogram marking Activity performed to apply the API Monogram to equipment under controlled conditions that has been produced within a quality management system and conforms to the applicable API product specification in every detail

Page 7: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

3

3.1.9 off-site Activity performed at a different, related facility of the licensed organization under a QMS conforming to industry standards applicable to the activities performed 3.1.10 on-site Activity performed at the facility identified on the API Monogram License 3.1.11 outsourced Activity performed at a qualified outside (non-related) organization NOTE: Outsourced activities conform to the requirements of API Q1, clause 5.6.1.6.

3.1.12 product marking Activity involving application of the markings required by the applicable API product specifications 3.1.13 remanufacture Activity involving disassembly, reassembly and testing of products and equipment, with or without the replacement of parts other than bodies, where machining, welding, heat treating or other manufacturing operations are employed 3.1.14 repair Activity involving disassembly, reassembly and testing of products and equipment, with or without the replacement of parts other than bodies, without machining, welding, heat treating or other manufacturing operations

3.2 Acronyms and Abbreviations For the purposes of this technical report, the following definitions apply: AMA alternate marking agreement API American Petroleum Institute ASME American Society of Mechanical Engineers BOP blowout preventer CC centrifugally cast CMC-HVT carboxymethylcellulose — high-viscosity, technical-grade CMC-LVT carboxymethylcellulose — low-viscosity, technical-grade CRA corrosion resistant alloy FAT final acceptance test FRP fiber reinforced plastic

Page 8: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

4

FW filament wound HP horse power ISO International Organization for Standardization NDE nondestructive examination OCMA Oil Companies' Materials Association PAC-HV high-viscosity polyanionic cellulose PAC-LV low-viscosity polyanionic cellulose PDC olycrystalline diamond compact PE polyethylene QMS quality management system RCD rotating control device SSV surface safety valve TFL through flowline USV underwater safety valve

4 Categories of Licensees

4.1 General This Technical Report establishes categories of API Monogram licensees based on the products produced and the production activities required. Organizations that perform multiple types of activities such as machining and assembly of components may be assigned multiple categories. Licensees under each of the following Categories shall have equipment and personnel and shall perform the required processes needed to produce the products under the scope of the license and the category of the licensee.

4.2 Mill/Processor A Mill/Processor is an organization that transforms material into finished product through cold or hot forming, extruding, seam welding, blending, molding, heat treating, upsetting, casting, forging, etc.

4.3 Assembler An assembler is an organization that assembles components into finished products through welding, brazing, soldering, bolting, joining, braiding, weaving, etc. NOTE: This does not include disassembly and reassembly of purchased assembled products.

4.4 Test Agency

Page 9: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

5

A test agency is a third party organization that verifies the capabilities of finished products to meet specified requirements of API 6AV1 and/or API 14A.

4.5 Machiner A machiner is an organization that changes the physical dimensions of material and/or product through mechanical processing (cutting, grinding, honing, drilling, milling, turning, threading, etc.)

5 Categories of Organizations Ineligible for Licensing

5.1 General The following categories of organizations do not manufacture or produce products and/or components that are within the scope of the API Monogram Program and therefore are not eligible to receive a monogram license:

5.2 Distributor A distributor is an organization that buys and sells finished products and materials.

5.3 Designer A designer is an organization that performs engineering design activities.

5.4 Remanufacturer/Repairer A remanufacturer and/or repairer is an organization that repairs and/or remanufactures an existing used, worn, or damaged product through machining, welding, replacement of parts, other than bodies, to return the product to its original capability.

5.5 Plating/Coating Provider A plating/coating provider is an organization that applies surface finishes through chemical processing or through the application of protective coating(s).

6 Minimum Activities

6.1 General The following tables identify the categories of the licensees and the minimum activities that shall be performed by an organization in order to obtain and/or maintain an API license. The monogrammable products contained in each API product specification listed below are identified as either assembled equipment or components. The tables are first divided by product standard, types of products contained (assembly or component), the categories of licensees, and the minimum activities to be performed by the licensees.

6.2 API Specifications 2B, 2C, 2F, 2H, 2MT1, 2MT2, 2W, 2Y 6.2.1 Assembled Equipment

Page 10: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

6

Examples of Assembled Equipment: Offshore Cranes (2C), Mooring Chain (2F), Flash Welded Chain (2F)

Licensee Category: Assembler (see Table1)

Table 1: Assembler Activities for Specifications 2C and 2F Assembled Equipment ACTIVITY WHERE PERFORMED

Assembly On-site

In-process Inspection On-site or Off-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

6.2.2 Components Examples of Components: Structural Steel Pipe, Forged Connecting Links, Plate, Rolled Carbon Manganese Steel Plate, Rolled Shapes, Steel Plates Licensee Category: Mill (see Table 2)

Table 2: Mill Activities for 2B, 2F, 2H, 2MT1, 2MT2, 2W, 2Y Components ACTIVITY WHERE PERFORMED

Forming On-site

Welding On-site

Product Marking On-site

Monogram Marking On-site

6.3 API Specification 4F: Drilling Structures Examples of Structures: Masts, Derricks, Crown Block Assemblies, Substructures Licensee Category: Assembler (see Table 3)

Table 3: Assembler Activities for 4F Structures ACTIVITY WHERE PERFORMED

Assembly On-site

In-process Inspection On-site or Off-site

Final Inspection On-site

Product Marking On-site

Monogram Marking On-site

6.4 API Specifications 5B, 5CT, 5L, 5LC, 5LCP, 5LD, 5CRA, 5DP, 5ST 6.4.1 Components Examples of Components: Casing, Tubing, Line Pipe, Pup Joints, Coiled Tubing, Lined Steel Pipe, Clad Steel Pipe, Coiled Line Pipe

Page 11: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

7

Licensee Category: Mill (see Table 4)

Table 4: Mill Activities for 5CT, 5L, 5LC, 5LCP, 5LD, 5CRA, 5DP, 5ST Components ACTIVITY WHERE PERFORMED

Forming On-site

Welding On-site

Product Marking On-site

Final Inspection On-site, Off-site

Monogram Marking On-site, AMA Allowed

6.4.2 Processing Examples of processing: Upsetting, Cladding, Heat Treating Licensee Category: Processor (see Table 5)

Table 5: Processor Activities for 5CT, 5L, 5LC, 5LCP, 5LD, 5CRA, 5DP, 5ST Components ACTIVITY WHERE PERFORMED

Cladding On-site

Upsetting On-site

Heat Treating On-site

Product Verification Testing On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site, AMA Allowed

6.4.3 Couplings Examples of Components: Couplings Licensee Category: Machiner (see Table 6)

Table 6: Machiner Activities for 5CT, 5L, 5LC, 5LD, 5CRA, 5ST Couplings ACTIVITY WHERE PERFORMED

Receiving Verification On-site

Threading On-site

In-process Inspection On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

Plating/Coating On-site

6.4.4 Master Ring and Plug Gauges Examples of Master Gauges: Thread Gauges Licensee Category: Machiner (see Table 7)

Page 12: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

8

Table 7: Machiner Activities for 5B Thread Gauges ACTIVITY WHERE PERFORMED

Threading On-site

Inspection On-site

Product Marking On-site

Monogram Marking On-site

6.4.5 Assembled Equipment Examples of Assembled Equipment: Drill Pipe Assembly Licensee Category: Assembler (see Table 8)

Table 8: Assembler Activities for 5DP Assembled Drill Pipe ACTIVITY WHERE PERFORMED

Drill Pipe Assembly On-site

Final Inspection On-site

Product Marking On-site

Monogram Marking On-site

6.5 Specifications 6A, 6AV1, 6D, 6DSS, 600, 602, 603, 608, 609 6.5.1 Assembled Equipment Examples of assembled equipment: Valves, Fluid Sampling Devices, Casing/Tubing Hangers, Chokes, SSV/USV, SSV/USV Actuators, Back Pressure Valves, Actuators, Casing and Tubing Heads, Check Valves, Metal Plug Valves, Bolted Bonnet Steel Gate Valves, Compact Steel Gate Valves/Globe Valves/ Check Valves, Corrosion-Resistant Bolted Bonnet Gate Valves, Metal Ball Valves, Butterfly Valves, Licensee Category: Assembler (see Table 9)

Table 9: Assembler Activities for 6A, 6AV1, 6D, 6DSS, 600, 602, 603, 608 and 609 Assembled Equipment

Activity Where Performed

Final Assembly On-site

Verification Testing On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

6.5.2 Components Examples of components: Crossover Connectors, Tubing Head Adapters, Top Connectors, Tees/Crosses, Adapter/Spacer Spools, Flange Connectors, Threaded Connectors, Other End Connectors, Bull Plugs, Valve removal Plugs, Ring Gaskets. Licensee Category: Machiner (see Table 10)

Page 13: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

9

Table 10: Machiner Activities for 6A, 6AV1, 6DSS, 600, 602, 603, 608 and 609 Components ACTIVITY WHERE PERFORMED

Machining On-site or Off-site

Special Machining [proprietary threads/profiles]

On-site, Off-site or Outsourced

In-process Inspection On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

Category: Test Agency (see Table 11)

Table 11: Test Agency Activities for 6AV1 Assembled Equipment

Activity Where Performed

Validation Testing On-site

Monogram Marking On-site

6.6 API Specifications 7-1, 7-2, 7F, 7K, 7NRV 6.6.1 Assembled Equipment Examples of Assembled Equipment: Heavyweight Drill Pipe, Roller Bits, Blade Drag Bits, Diamond Bits, PDC Bits, Kelly Valves, Roller Chain, Rotary Tables, Rotary Slips, High Pressure Hoses, Spiders, Manual Tongs, Power Tongs, Safety Clamps, BOP Handling Systems, Drill String Non-Return Valve, Non-Return Valve Equalizing Heads Licensee Category: Assembler (see Table 12)

Table 12: Assembler Activities for 7-1, 7-2, 7F, 7K, 7NRV Assembled Equipment ACTIVITY WHERE PERFORMED

Sub-Assembly On-site or Off-site

Welding On-site or Off-site

Final Assembly On-site

Verification Testing On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

6.6.2 Components Examples of Components: Kelly’s, Drill Stem Subs, Drill Collars, Rotary Shouldered Connections, Thread Gauges, Mud Pump Components, Drawworks Components, Rotary Bushings, Non-Return Valve Subs, Non-return Valve Nipples Licensee Category: Machiner (see Table13)

Page 14: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

10

Table 13: Machiner Activities for 7-1, 7-2, 7F, 7K, 7NRV Components ACTIVITY WHERE PERFORMED

Machining On-site or Off-site

Special Machining [proprietary threads/profiles]

On-site, Off-site or Outsourced

In-process Inspection On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

6.6.3 Threaded Components Examples of threaded components: Drill Stem Subs, Drill Collars, Rotary Shouldered Connections, Thread Gauges, Licensee Category: Machiner (see Table14)

Table 14: Machiner Activities for 7-1, 7-2, 7F, 7K, 7NRV Components ACTIVITY WHERE PERFORMED

Threading On-site

Product Marking On-site

Inspection On-site

Monogram Marking On-site

6.7 API Specification 8C 6.7.1 Assembled Equipment Examples of Assembled Equipment: Travelling Blocks, Hook Blocks, Block to Hook Adapters, Drilling Hooks, Tubing Hooks, Sucker Rod Hooks, Casing Elevators, Tubing Elevators, Drill Pipe Elevators, Drill Collar Elevators, Sucker Rod Elevators, Rotary Swivels, Power Swivels, Power Subs, Spiders (Capable of being used as Elevators), Wireline Anchors, Drill String Motion Compensators, Kelly Spinners (Capable of being used as Hoisting Equipment) Pressure Vessels and Piping Mounted on Hoisting Equipment, Safety Clamps (Capable of being used as Hoisting Equipment), Guide Dollies for Travelling Equipment. Licensee Category: Assembler (see Table 15)

Table 15: Assembler Activities for 8C Assembled Equipment ACTIVITY WHERE PERFORMED

Sub-Assembly On-site or Off-site

Welding On-site or Off-site

Final Assembly On-site

Verification Testing On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

6.7.2 Components

Page 15: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

11

Examples of Components: Hoisting Sheaves, Connectors and Link adapters, Elevator Links, Rotary Swivel Bale Adapters. Licensee Category: Machiner (see Table 16)

Table 16: Machiner Activities for 8C Components ACTIVITY WHERE PERFORMED

Machining On-site

In-process Inspection On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

6.8 API Specification 9A 6.8.1 Assemblies Examples of Assemblies: Bright or Drawn Galvanized Wire Rope, Mooring Wire Rope, Torpedo Lines, Well Measuring Strand, Wire Guide Strand, Structural Rope and Strand Licensee Category: Assembler (see Table 17)

Table 17: Assembler Activities for 9A Assembled Equipment ACTIVITY WHERE PERFORMED

In-process Inspection On-site or Off-site

Welding On-site or Off-site

Final Assembly On-site

Final Inspection On-site

Monogram Marking On-site

6.8.2 Components Example of Components: Well Measuring Wire. Licensee Category: Mill (see Table 18)

Table 18: Mill Activities for 9A Components ACTIVITY WHERE PERFORMED

Drawing/Forming On-site

Final Inspection On-site

Monogram Marking On-site

6.9 API Specifications 10A, 10D 6.9.1 Assembled Equipment Examples of assembled equipment: Centralizers Licensee Category: Assembler (see Table 19)

Page 16: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

12

Table 19: Assembler Activities for 10D Assembled Equipment ACTIVITY WHERE PERFORMED

Sub-Assembly On-site or Off-site

Welding On-site or Off-site

Final Assembly On-site

Verification Testing On-site

Final Inspection On-site

Monogram Marking On-site

6.9.2 Component Examples of Component: Cement Licensee Category: Mill (see Table 20)

Table 20: Mill Activities for 10A Cement ACTIVITY WHERE PERFORMED

Blending On-site

Chemical Analysis On-site

Baking (Kiln) On-site

Verification Testing On-site

Final Inspection On-site

Monogram Marking On-site

6.10 API Specifications 11AX, 11B, 11D1, 11E 6.10.1 Assembled Equipment Examples of assembled equipment: Subsurface Sucker Rod Pumps, Pumping Unit Structure, Gear Reducers, Packers, Bridge Plugs, Stuffing Boxes, FRP Sucker Rods, Polished Rod Clamps Licensee Category: Assembler (see Table 21 and Table 22)

Table 21: Assembler activities for 11AX, 11B, 11E Assembled Equipment ACTIVITY WHERE PERFORMED

Verification Testing On-site

Final Assembly On-site

Final Inspection On-site

Final FAT Testing On-site

Monogram Marking On-site

Table 22: Assembler Activities for 11D1 Assembled Equipment

Activity Where Performed

Verification Testing On-site

Final Assembly On-site Final Inspection On-site

Final FAT Testing On-site Monogram Marking On-site

Page 17: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

13

6.10.2 Component/Machined Products Examples of Component/Machined Products: Balls, Seats, Rod Pump Fittings, Plungers, Barrels, Pull Tubes, Valve Rods, Cages, Sucker Rod Couplings, Polished Rods, Seating Cups, Sub-Couplings, Polished Rod Couplings, Pumping Tees, Sinker Bars, Steel Pony Rods, Thread Gauges Licensee Category: Machiner (see Table 23)

Table 23: Machiner Activities for 11AX, 11B, 11D1, 11E Components ACTIVITY WHERE PERFORMED

Machining On-site

In-process Inspection On-site

Final Inspection On-site

Monogram Marking On-site

6.10.3 Components Examples of components: Sucker Rods/Pony Rods Licensee Category: Mill (see Table 24)

Table 24: Mill Activities for 11E Components ACTIVITY WHERE PERFORMED

Upsetting On-site

Threading On-site

Final Inspection On-site

Coating On-site

Monogram Marking On-site

Licensee Category: Processor (Forming Non-metallic Product, see Table 25)

Table 25: Processor Activities for 11AX, 11B, 11E Nonmetallic Components ACTIVITY WHERE PERFORMED

Molding/forming On-site or Off-site

In-process Inspection On-site or Off-site

Final Inspection On-site

Monogram Marking On-site

6.10.4 Master Ring and Plug Gauges Examples of Master Gauges: Thread Gauges Licensee Category: Machiner

Table 26: Machiner Activities for 11B Thread Gauges ACTIVITY WHERE PERFORMED

Threading On-site

Inspection On-site

Product Marking On-site

Monogram Marking On-site

Page 18: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

14

6.11 API Specifications 12B, 12D, 12F, 12J, 12K, 12L, 12P and 650 Series Assembled Equipment: Examples of assembled equipment: Shop Welded Tanks, Field Welded Tanks, Bolted Tanks, Indirect Type Oilfield Heaters, FRP Tanks, Oil and Gas Separators, Indirect Type Oilfield Heaters (Heaters/Shells/Coils), Vertical and Horizontal Emulsion Treaters, Welded Tanks for Oil Storage –Fabricated Steel Plates and Shop Built Tanks Licensee Category: Assembler (see Table 27)

Table 27: Assembler Activities for 12B, 12D, 12F, 12J, 12K, 12L, 12P and 650 Assembled Equipment

ACTIVITY WHERE PERFORMED

Sub-Assembly On-site

In-process Inspection On-site

Shop Welding On-site or Off-site

Field Welding Field Location

Final Assembly On-site

Forming (FRP) On-site

Verification Testing On-site or (Field for 12D only)

NDE Testing On-site or (Field for 12D only)

Final Inspection On-site or (Field for 12D only)

Monogram Marking On-site or (Field for 12D only)

Painting/Coating On-site or (Field for 12D only)

Storage/Preservation On-site or Off-site

6.12 API Specification 13A Components: Oil Well Drilling Fluids Examples of Components: Barite, Bentonite, Non-treated Bentonite, Attapugite, Sepiolite, CMV-LVT, CMT-HVT, Starch, OCMA Grade Bentonite, PAC-LV, PAC-HV, Drilling Grade Xanthan Gum Licensee Category: Mill (see Table 28)

Table 28: Mill Activities for 13A Components ACTIVITY WHERE PERFORMED

Blending On-site

Chemical Analysis On-site

Baking (Kiln) On-site

Verification Testing On-site

Final Inspection On-site

Monogram Marking On-site

Storage/Preservation On-site or Off-site

Page 19: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

15

6.13 API Specifications 14A, 14L 6.13.1 Assembled Equipment Examples of assembled equipment: Sub-Surface Safety Valves, Lock Mandrels Licensee Category: Assembler (see Table 29)

Table 29: Assembler Activities for 14A, 14L Assembled Equipment ACTIVITY WHERE PERFORMED

Procurement On-site or Off-site

Receiving Verification On-site

Final Assembly On-site

Verification Testing On-site

Final Inspection On-site

Monogram Marking On-site

6.13.2 Components Examples of Components: Landing Nipples Licensee Category: Machiner

Table 30: Machiner Activities for 14A, 14L Components ACTIVITY WHERE PERFORMED

Receiving Verification On-site

Machining On-site or Off-site

In-process Inspection On-site

Final Inspection On-site

Monogram Marking On-site

Licensee Category: Test Agency (see Table 31)

Table 31: Test Agency Activities for 14A Assembled Equipment

Activity Where Performed

Validation Testing On-site

Monogram Marking On-site

6.14 API Specifications 15HR, 15LE, 15LR 6.14.1 Components Examples of components: High Pressure Fiberglass Line Pipe – Line Pipe, Couplings, Fittings, Flanges, Reducers and Adapters, Polyethylene (PE) Line Pipe, Low Pressure Fiberglass Line Pipe, CC Line Pipe; FW Line Pipe. Licensee Category: Mill/Processor (forming non-metallic product, see Table 32)

Page 20: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

16

Table 32: Mill/Processor Activities for 15HR, 15LE, 15LR Components ACTIVITY WHERE PERFORMED

Molding/forming/extruding On-site or Off-site

In-process Inspection On-site or Off-site

Final Inspection On-site

Monogram Marking On-site

6.15 API Specifications 16A, 16C, 16D, 16F, 16R, 16RCD 6.15.1 Assembled Equipment Examples of assembled equipment: Ram BOP, Annular BOP, Annular Packing Units, Hydraulic Connectors, Clamps, Actuated Valve Control Lines, Drilling Choke Actuators, Drilling Choke Control Lines, Drilling Choke Controls, Drilling Chokes, Flexible Choke and Kill Lines, Rigid Choke and Kill Lines, Swivel Unions, Control Systems for Surface Mounted BOP Stacks, Control Systems for Subsea BOP Stacks, Discrete Hydraulic Control Systems for Subsea BOP Stacks, Electro-Hydraulic/Multiplex Control Systems for Subsea BOP Stacks, Control Systems for Diverter Equipment, Auxiliary Equipment Control Systems and Interfaces, Emergency Disconnect Sequence Systems, Backup Systems, Special Deepwater/Harsh Environment Systems, Active/Passive/Hybrid RCD, RCD Bearing Assemblies, RCD Packer Units, RCD Housing Clamps, Riser Tensioner Equipment, Flex Ball Joints, Telescopic Joint (Slip Joint), Riser Joints, Riser Running Equipment Licensee Category: Assembler (see Table 33)

Table 33: Assembler Activities for 16A, 16C, 16D, 16F, 16R, 16RCD Assembled Equipment ACTIVITY WHERE PERFORMED

Procurement On-site or Off-site

Receiving Verification On-site

Sub-Assembly On-site or Off-site

Welding On-site or Off-site

Final Assembly On-site

Verification Testing On-site

Final Inspection On-site

Monogram Marking On-site

6.15.2 Components Examples of Components: Ram Blocks, Packers & Top Seals, Drilling Spools, Adapters, Loose Connections, Tensioner Rings, Clamps, Union Connections, Riser Couplings, Annular Seals, Lower Riser Adapter, Buoyancy Equipment Licensee Category: Machiner

Page 21: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

17

Table 34: Machiner Activities for 16A, 16C, 16D, 16F, 16R, 16RCD Components ACTIVITY WHERE PERFORMED

Receiving Verification On-site

Machining On-site or Off-site

Special Machining [proprietary threads/profiles]

On-site, Off-site or Outsourced

In-process Inspection On-site

Final Inspection On-site

Monogram Marking On-site

Licensee Category: Processor (forming non-metallic product)

Table 35: Processor Activities for 16A, 16C, 16D, 16F, 16R, 16RCD ACTIVITY WHERE PERFORMED

Molding/forming On-site or Off-site

In-process Inspection On-site or Off-site

Final Inspection On-site

Monogram Marking On-site

6.16 API Specifications 17D, 17E, 17J, 17K 6.16.1 Assembled Equipment Examples of assembled equipment: Tubing Hangers, Running Tools a) Sub-Sea Wellheads: Sub-Sea Wellheads, Conductor Housings, Wellhead Housings, Seal

Assemblies, Guide-Bases, Bore Protectors and Wear Bushings, Corrosion Caps, Casing and Tubing Hangers and Seal Assemblies

b) Mudline Suspension Systems: Wellheads, Running Tools, Casing Hangers, Casing Hanger Tools, Tie Back Tools for Sub-Sea Completions, Subsea Completion Adapters for Mudline Wellheads, Tubing Heads, Corrosion caps, Tieback Housings,

c) Drill-through Mudline Suspension Systems: Conductor Housings, Surface Casing Hangers,

Wellhead Housing, Casing Hangers, Annular Seal Assemblies, Bore Protectors and Wear Bushings, Abandonment Caps,

d) Miscellaneous Equipment: Flanged End and Outlet Connections, Clamp Hub Type Connections,

Threaded End and Outlet Connections, Other End Connections, Studs and Nuts, Ring Joint Gaskets, Guideline Establishment Equipment. Tree Connectors and Valves, Valve Blocks, Valve Actuators, Chokes, Choke Actuators, Lead Test and Isolation Valves, TFL-wye Spool, Re-entry Interface Tree Caps, Tree Piping, Tree Guide Frames, Tree Running Tools, Tree Cap Running Tools Tree Mounted Flow Line Umbilical, Tubing Heads, Tubing Head Connectors, Flow Line Bases and Running/Retrieval, Tree Mounted Control Interfaces, Flanged Connectors, Flow Line and Umbilical Connectors, Tree Connectors and Tubing Head Connectors

e) Sub-Sea Umbilicals (17E) f) Unbonded Flexible Pipe (17J) g) Bonded Flexible Pipe (17K)

Page 22: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

18

Licensee Category: Assembler (see Table 36)

Table 36: Assembler Activities for 17D, 17E, 17J, 17K Assembled Equipment

ACTIVITY WHERE PERFORMED

Final Assembly On-site

Verification Testing On-site

Final Inspection On-site

Monogram Marking On-site

6.16.2 Component Equipment Examples of Components: Casing Hangers, Threaded Connectors, Other End Connectors (Including

Clamp Hub‐type), Adaptors, Spools (including Wye and Re‐entry), Tubing Heads, Caps and Crown Plugs,

Piping, Ring Joint Gaskets, Sub‐Mudline Housings Licensee Category: Machiner (see Table 37)

Table 37: Machiner Activities for 17D Components ACTIVITY WHERE PERFORMED

Machining On-site or Off-site

Special Machining [proprietary threads/profiles]

On-site, Off-site or Outsourced

In-process Inspection On-site

Final Inspection On-site

Monogram Marking On-site

6.17 API Specifications 19G1, 19G2, 19G3, 19V 6.17.1 Assembled Equipment Example of assembled equipment: Side Pocket Mandrel, Flow Control Devices for Side Pocket Mandrels, Subsurface Barrier Valve, Barrier Valve Tools, Running and Pulling Tools, Kick-over Tools, Latches for Side Pocket Mandrels Licensee Category: Assembler (see Table 38)

Table 38: Assembler Activities for 19G1, 19G2, 19G3, 19V Assembled Equipment ACTIVITY WHERE PERFORMED

Welding On-site

Final Assembly On-site

Final Inspection On-site

Final FAT Testing On-site

Monogram Marking On-site

6.18 API Specifications 20A, 20B, 20C, 20E, 20F 6.18.1 Components (Castings and Forgings) Examples of components: Castings, Open Die Forgings, Closed Die Forgings Licensee Category: Processor (API 20A)

Page 23: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

19

Table 39: Processor Activities for 20A Components

ACTIVITY WHERE PERFORMED

Melting / Pouring On-site

Heat Treating On-site

Chemical testing On-site

Welding repair On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

Licensee Category: Processor (API 20B and API 20C, see Table 40)

Table 40: Processor Activities for 20B, 20C Components

ACTIVITY WHERE PERFORMED

Material Procurement On-site or Off-site

Receiving Verification On-site or Off-site

Final Forging On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

6.18.2 Component (Bolting) Examples of threaded components: Carbon, and Alloy/CRA Steel Bolting Licensee Category: Machiner (see Table 41)

Table 41: Machiner Activities for 20E, 20F Components ACTIVITY WHERE PERFORMED

Machining On-site

Roll Threading On-site

Hardness Testing On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

Licensee Category: Mill (see Table 42)

Table 42: Mill Activities for 20A, 20E, 20F Components ACTIVITY WHERE PERFORMED

Cold Forming (Type C) On-site

Hot Forming -Type D, E, H & I On-site

Hardness Testing On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

Page 24: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

20

6.19 API Standard 547 6.19.1 Assembled Equipment Examples of assembled equipment: Form-Wound Squirrel Cage Induction Motors – 250 HP or Larger Licensee Category: Assembler (see Table 43)

Table 43: Assembler Activities for 547 Assembled Equipment ACTIVITY WHERE PERFORMED

Final Assembly On-site

Verification Testing On-site

Final Inspection On-site

Product Marking On-Site

Monogram Marking On-Site

6.20 API Standard 594 and 599 6.20.1 Assembled Equipment Examples of assembled equipment: Check Valves, Metal Plug Valves Licensee Category: Assembler (see Table 44)

Table 44: Assembler Activities for 594 and 599 Assembled Equipment ACTIVITY WHERE PERFORMED

Final Assembly On-site

Verification Testing On-site

Product Marking On-site

Final Inspection On-site

Monogram Marking On-site

Bibliography [1] API Spec Q1, Specification for Quality Management System Requirements for Manufacturing

Organizations for the Petroleum and Natural Gas Industry

[2] API Spec 2B, Specification for the Fabrication of Structural Steel Pipe

[3] API Spec 2C, Offshore Pedestal-mounted Cranes

[4] API Spec 2F, Specification for Mooring Chain

[5] API Spec 2H, Specification for Carbon Manganese Steel Plate for Offshore Structures

[6] API Spec 4F, Specification for Drilling and Well Servicing Structures

[7] API Spec 5B, Specification for Threading, Gauging and Thread Inspection of Casing, Tubing, and Line Pipe Threads

[8] API Spec 5CT, Specification for Casing and Tubing

[9] API Spec 5CRA, Specification for Corrosion-resistant Alloy Seamless Tues for Use as Casing, Tubing, and Coupling Stock

Page 25: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

21

[10] API Spec 5DP, Specification for Drill Pipe

[11] API Spec 5L, Specification for Line Pipe

[12] API Spec 5LC, CRA Line Pipe

[13] API Spec 5LCP, Specification for Coiled Line Pipe

[14] API Spec 5LD, Specification for CRA Clad or Lined Steel Pipe

[15] API Spec 5ST, Specification for Coiled Tubing U.S. Customary and SI Units

[16] API Spec 6A, Specification for Wellhead and Christmas Tree Equipment

[17] API Spec 6AV1, Specification for Validation of Wellhead Surface Safety Valves and Underwater Safety Valves for Offshore Service

[18] API Spec 6D, Specification for Pipeline and Piping Valves

[19] API Spec 6DSS, Specification for Subsea Pipeline Valves

[20] API Spec 7-1, Specification for Rotary Drill Stem Elements

[21] API Spec 7-2, Specification for Threading and Gauging of Rotary Shouldered Thread Connections

[22] API Spec 7F, Oil Field Chain and Sprockets

[23] API Spec 7K, Drilling and Well Servicing Equipment

[24] API Spec 7NRV, Specification for Drill String Non-return Valves

[25] API Spec 8C, Drilling and Production Hoisting Equipment (PSL 1 and PSL 2)

[26] API Spec 9A, Specification for Wire Rope

[27] API Spec 10A, Specification for Cements and Materials for Well Cementing

[28] API Spec 10D, Specification for Bow-string Casing Centralizers

[29] API Spec 11AX, Specification for Subsurface Sucker Rod Pump Assemblies, Components, and Fittings

[30] API Spec 11B, Specification for Sucker Rods, Polished Rods and Liners, Couplings, Sinker Bars, Polished Rod Clamps, Stuffing Boxes, and Pumping Tees

[31] API Spec 11D1, Packers and Bridge Plugs

[32] API Spec 11E, Specification for Pumping Units

[33] API Spec 12B, Specification for Bolted Tanks for Storage of Production Liquids

[34] API Spec 12D, Specification for Large Welded Production Tanks

[35] API Spec 12F, Specification for Shop Welded Tanks for Storage of Production Liquids

[36] API Spec 12J, Specification for Oil and Gas Separators

[37] API Spec 12K, Specification for Indirect Type Oilfield Heaters

[38] API Spec 12L, Specification for Vertical and Horizontal Emulsion Treaters

[39] API Spec 12P, Specification for Fiberglass Reinforced Plastic Tanks

[40] API Spec 13A, Specification for Drilling Fluids Materials

[41] API Spec 14A, Specification for Subsurface Safety Valve Equipment

[42] API Spec 14L, Specification for Lock Mandrels and Landing Nipples

[43] API Spec 16A, Specification for Drill-Through Equipment

Page 26: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

22

[44] API Spec 16C, Chock and Kill Equipment

[45] API Spec 16F, Specification for Marine Drilling Riser Equipment

[46] API Spec 16R, Specification for Marine Drilling Riser Couplings

[47] API Spec 16RCD, Specification for Rotating Control Devices

[48] API Spec 17D, Design and Operation of Subsea Production Systems-Subsea Wellhead and Tree Equipment

[49] API Spec 17E, Specification for Subsea Umbilicals

[50] API Spec 17J, Specification for Unbonded Flexible Pipe

[51] API Spec 17K, Specification for Bonded Flexible Pipe

[52] API Spec 19G1, Side-pocket Mandrels

[53] API Spec 19G2, Flow-control Devices for Side-pocket Mandrels

[54] API Spec 19G3, Running Tools, Pulling Tools, and Kick-over Tools and Latches for Side-pocket Mandrels

[55] API Spec 20A, Carbon Steel, Alloy Steel, Stainless Steel, and Nickel Base Alloy Castings for Use in the Petroleum and Natural Gas Industry

[56] API Spec 20B, Open Die Shaped Forgings for use in the Petroleum and Natural Gas Industry

[57] API Spec 20C, Closed Die Forgings for Use in the Petroleum and Natural Gas Industry

[58] API Spec 20E, Alloy and Carbon Steel Bolting for Use in the Petroleum and Natural Gas Industries

[59] API Spec 20F, Corrosion Resistant Bolting for Use in the Petroleum and Natural Gas Industries

[60] API Std 547, General-purpose Form-wound Squirrel Cage Induction Motors 250 Horsepower and Larger

[61] API Std 594, Check Valves: Flanged, Lug, Wafer, and Butt-welding

[62] API Std 599, Metal Plug Valves – Flanged, Threaded and Welding Ends

[63] API Std 600, Steel Gate Valves – Flanged and Butt-welding Ends, Bolted Bonnets

[64] API Std 602, Gate, Globe, and Check Valves for Sizes DN 100 (NPS 4) and Smaller for the Petroleum and Natural Gas Industries

[65] API Std 603, Corrosion-resistant, Bolted Bonnet Gate Valves – Flanged and Butt-welding Ends

[66] API Std 608, Metal Ball Valves – Flanged, Threaded, and Welding Ends

[67] API Std 609, Butterfly Valves: Double-flanged Lug- and Wafer-type

[68] API Std 650, Welded Tanks for Oil Storage

Page 27: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

23

ANNEX A (Informative)

Summary Matrix

The matrix below identifies the API product specifications the monogrammable products within each specification, the categories of the licensees, the corresponding table of required activities, and the page location of each table.

SPECIFICATION PRODUCTS CATEGORY TABLE PAGE

2B Structural Steel Pipe Mill 2

2C Offshore Cranes Assembler 1

2F Mooring Chain, Flash Welded Chain Assembler 1

Forged Connecting Links Mill 2

2H Grade 42 Steel Plate, Grade 50 Steel Plate

Mill 2

2MT1 Grade 2 MT1 Steel Plate Mill 2

2MT2 Steel Rolled Shapes Mill 2

2W Grade 50 Steel Plate Grade 60 Steel Plate

Mill 2

2Y Grade 50 Steel Plate Grade 60 Steel Plate

Mill 2

4F Product Specification Level Masts, Derricks, Substructures, Crown Block Assemblies

Assembler 3

5B Thread Gauges – Threader Machiner 7

5CRA

CRA Seamless Casing and Tubing Mill 4

Upsetting, Heat Treating Processor 5

Couplings Machiner 6

Threader Machiner 6

5CT

Casing, Tubing Mill 4

Upsetting, Heat Treating Processor 5

Couplings Machiner 6

Threader Machiner 6

5DP

Drill Pipe Body, Tool Joint Mill 4

Drill Pipe Assembler 8

Upsetting, Heat Treating Processor 5

Threader Machiner 6

5L

Line Pipe-Plain End PSL1 & PSL2 Mill 4

Line Pipe Threaded & Coupled Mill 4

Upsetting, Heat Treating Processor 5

Line Pipe Couplings Machiner 6

Threader Machiner 6

5LC

CRA Line Pipe Mill 4

Heat Treating Processor 5

Couplings Machiner 6

Threader Machiner 6

5LCP Coiled Line Pipe Mill 4

5LD

CRA Clad or Lined Steel Pipe Mill 4

Upsetting, Heat Treating Processor 5

Couplings Machiner 6

Threader Machiner 6

Page 28: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

24

SPECIFICATION PRODUCTS CATEGORY TABLE PAGE

5ST

Coiled Tubing Mill 4

Upsetting, Heat Treating Processor 5

Couplings Machiner 6

Threader Machiner 6

6A

Valves, Fluid Sampling Devices, Casing/Tubing Hangers, Chokes, SSV/USV, SSV/USV Actuators, Back Pressure Valves, Actuators, Casing and Tubing Heads, Check Valves, Metal Plug Valves, Bolted Bonnet Steel Gate Valves, Compact Steel Gate Valves/Globe Valves/ Check Valves, Corrosion-Resistant Bolted Bonnet Gate Valves, Metal Ball Valves

Assembler 9

Casing & Tubing Heads, Crossover Connectors, Tubing Head Adapters, Top Connectors, Tees/Crosses, Adapter & Spacer Spools, Flange Connectors, Threaded Connectors, Other End Connectors, Bull Plugs, Valve removal Plugs, Ring Joint Gaskets

Machiner 10

6AV1 Verification Testing of Wellhead Surface Safety Valves and Underwater Safety Valves for Offshore Use

Testing Agency

11

6D Gate Valves, Plug Valves, Ball Valves, Check Valves Assembler 9

6DSS Subsea Gate Valves, Subsea Plug Valves, Subsea Ball Valves, Subsea Check Valves

Assembler 9

7-1

Heavyweight Drill Pipe, Roller Bits, Blade Drag Bits, Diamond Bits, PDC Bits, Kelly Valves, Stabilizers

Assembler 12

Kelly Valves, Kelly’s, Drill Stem Subs, Drill Collars, Drilling and Coring Bits

Machiner 13

Threader Machiner 14

7-2 Rotary Shouldered Connection Thread Gauges Machiner 13

7F Roller Chain Assembler 12

7K

Rotary Tables, Rotary Slips, High Pressure Hoses, Spiders, Manual Tongs, Power Tongs, Safety Clamps, BOP Handling Systems

Assembler 12

Drill Collars, Rotary Shouldered Connections, Thread Gauges, Mud Pump Components, Drawworks Components, Kelly Bushings, Master Bushings

Machiner 13

Rotary Shouldered Connections Thread Gauges, (Threader) Machiner 14

7K Drill String Non-return Valves, Non-Return Valve Subs, Non-return Valve Landing Nipples

Assembler 12

7NRV

Non-return Valve Equalizing Heads and all components that establish tolerances and/or clearances which may affect performance or interchangeability of the NRV equipment

Machiner 13

Threader Machiner 14

8C

Travelling Blocks, Hook Blocks, Block to Hook Adapters, Drilling Hooks, Tubing Hooks, Sucker Rod Hooks, Casing Elevators, Tubing Elevators, Drill Pipe Elevators, Drill collar Elevators, Sucker Rod Elevators, Rotary Swivels, Power Swivels, Power Subs, Spiders (capable of being used as Elevators), Wireline Anchors, Drill String Motion Compensators, Kelly Spinners (if capable of being used as Hoisting Equipment) Pressure Vessels and Piping Mounted on Hoisting Equipment, Safety Clamps (capable of being used as Hoisting Equipment), Guide Dollies for Travelling Equipment

Assembler 15

Hoisting Sheaves, Connectors and Link Adapters, Elevator Links, Machiner 16

Page 29: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

25

SPECIFICATION PRODUCTS CATEGORY TABLE PAGE

Rotary Swivel Bail Adapters

9A

Bright or Drawn Galvanized Wire Rope, Mooring Wire Rope, Torpedo Lines, Well Measuring Strand, Wire Guide Strand, Structural Rope and Strand

Assembler 17

Well Measuring Wire Mill 18

10A Well Cement Mill 20

10D Casing Centralizers Assembler 19

11AX Sucker Rod Pumps, Pump Parts, Pump Parts without Tubing or Sucker Rod Threads, Seating Cups

Assembler 21

11B

Stuffing Boxes, FRP Sucker Rods, Polished Rod Clamps, Stuffing Box & Pumping Tees

Assembler 21

Steel Sucker Rods, Steel Pony Rods, FRP Sucker Rods, Sucker Rod Couplings, Sub-Couplings, Polished Rods, Polished Rod Couplings, Seating Cups, Sinker Bars, Steel Pony Rods

Machiner 23

Threading, Thread Gauges Machiner 26

Upsetting/Molding/Forming Processor 25

11D1 Packers, Bridge Plugs, Assembler 22

11E Pumping Unit Structure, Gear Reducers Assembler 21

Steel Sucker Rods, Steel Pony Rods Mill 24

12B Bolted Storage Tanks Assembler 27

12D Field Welded Storage Tanks Assembler 27

12F Shop Welded Storage Tanks Assembler 27

12J Oil and Gas Separators Assembler 27

12K Indirect Type Oilfield Heaters (Heaters/Shells/Coils) Assembler 27

12L Vertical and Horizontal Emulsion Treaters Assembler 27

12P Fiberglass Reinforced Plastic (FRP) Tanks Assembler 27

13A Barite, Barite 4.1, Bentonite, Non-treated Bentonite, Attapugite, Sepiolite, CMV-LVT, CMT-HVT, Starch, OCMA Grade Bentonite, PAC-LV, PAC-HV, Drilling Grade Xanthan Gum

Mill 28

14A

Sub-Surface Safety Valves Assembler 29

Validation Testing Test

Agency 31

14L Lock Mandrels Assembler 29

Landing Nipples Machiner 30

15HR High Pressure Fiberglass Line Pipe, Couplings, Fittings, Flanges, Reducers and Adapters

Mill / Processor

32

15LE Polyethylene (PE) Line Pipe, PE Fittings Mill /

Processor 32

15LR Low Pressure Fiberglass Line Pipe, CC Line Pipe, FW Line Pipe Mill /

Processor 32

16A

Ram BOP, Annular BOP, Annular Packing Units, Hydraulic connectors

Assembler 33

Ram Blocks, Packers & Top Seals, Drilling Spools, Adapters, Loose Connections

Machiner 34

Molding/Forming Processor 35

Page 30: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

26

SPECIFICATION PRODUCTS CATEGORY TABLE PAGE

16C

Actuated Valve Control Lines, Articulated Choke and Kill drilling, Drilling Choke Actuators, Drilling Choke Control Lines (exclusive of BOP Control Lines and Subsurface Safety Valve Control Lines) Drilling Choke Controls, Drilling Chokes, Flexible Choke and Kill Lines, Rigid Choke and Kill Lines, Swivel Joints, Choke and Kill Manifold Assemblies

Assembler 33

16D

Control Systems for Surface Mounted BOP Stacks, Hydraulic Control Systems for Subsea BOP Stacks, Electro-Hydraulic/multiplex Control Systems for Subsea BOP Stacks, Diverter Control Systems, Emergency Backup BOP Control Systems, Auxiliary Equipment Control Systems and Interfaces

Assembler 33

16F

Ram BOP, Annular BOP, Annular Packing Units, Hydraulic Connectors, Clamps, Riser Tensioner Equipment, Flex Ball Joints, Telescopic Joint (Slip Joint) and Tensioner Ring, Riser Joints, Riser Running Equipment

Assembler 33

Lower Riser Adapter, Buoyancy Equipment Machiner 34

Molding/forming Processor 35

16R Marine Drilling Riser Couplings Machiner 34

16RCD Rotating Control Devices, RCD packers Assembler 33

Molding/Forming Processor 35

17D

Subsea Wellheads, Mudline Wellheads, Valves, Valve Blocks, Valve Actuators, Chokes and Choke Actuators, Flanged Connectors, Casing Hangers, Tubing Hangers, Seal Assemblies

Assembler 36

Threaded Connectors, Flowline and Umbilical Connectors, Other End Connectors (including Clamp Hub‐type), Adaptors, Spools (including Wye and Re‐entry), Tubing Heads, Tree Connectors, Tubing Head Connectors, Caps and Crown Plugs, Piping, Ring Joint Gaskets, Conductor Housings, Wellhead Housings, Sub‐Mudline Housings, Tieback Housings, Guide Bases

Machiner 37

17E Subsea Umbilicals Assembler 36

17J Unbonded Flexible Pipe Assembler 36

17K Bonded Flexible Pipe Assembler 36

19G1 Side Pocket Mandrels Assembler 38

19G2 Flow Control Devices for Side Pocket Mandrels Assembler 38

19G3 Running and Pulling Tools, Kick-over Tools, Latches Assembler 38

19V Subsurface Barrier Valves Barrier Valve Tools Assembler 38

20A

Castings: Group A Carbon Steels, Group B Low Alloy Steels, Group C Stainless Steels other than Duplex, Group D Duplex Stainless Steels, Group E Nickle Based Alloys (CRA)

Processor 39

Cold Forming Mill 42

20B

Open Die Forgings: Group 1 Carbon Steel Forgings, Group 2 Alloy Steel Forgings, Group 3 Non-Duplex Stainless Steel Forgings, Group 4 Duplex Forgings, Group 5 Nickel Based Alloy Forgings

Processor 40

20C Closed Die Forgings Processor 40

20E

Cold Formed Bolts, Screws & Nuts, Fully Machined Bolts, Screws & Nuts Hot Formed Bolts, Screws & Nuts

Machiner 41

Cold Forming, Hot Forming Mill 42

Page 31: API Monogram Program: Definition of a Manufacturerballots.api.org/ecs/sc18/ballots/docs/18TR3TechReport...API Monogram Program: Definition of a Manufacturer API TECHNICAL REPORT 18TR3

27

SPECIFICATION PRODUCTS CATEGORY TABLE PAGE

20F

Cold Formed Bolts, Screws & Nuts, Fully Machined Bolts, Screws & Nuts Hot Formed Bolts, Screws & Nuts

Machiner 41

Cold Forming, Hot Forming Mill 42

547 Motors Assembler 43

594 Check Valves – Type A Check Valves – Type B

Assembler 44

599 Metal Plug Valves Assembler 44

600

Bolted Bonnet Steel Gate Valves, Flanged and Butt-welding Ends, Bolted Bonnets

Assembler 9

Flange Connectors, Threaded Connectors, Other End Connectors, Bull Plugs, Valve removal Plugs, Ring Gaskets

Machiner 10

602

Bolted Bonnet Steel Gate Valves, Compact Steel Gate Valves/Globe Valves/ Check Valves, Corrosion-Resistant Bolted Bonnet Gate Valves, Metal Ball Valves

Assembler 9

Crossover Connectors, Tubing Head Adapters, Top Connectors, Tees/Crosses, Adapter/Spacer Spools, Flange Connectors, Threaded Connectors, Other End Connectors, Bull Plugs, Valve removal Plugs, Ring Gaskets

Machiner 10

603

Corrosion-resistant, Bolted Bonnet Steel Gate Valves, Compact Steel Gate Valves/Globe Valves/ Check Valves, Corrosion-Resistant Bolted Bonnet Gate Valves, Metal Ball Valves

Assembler 9

Crossover Connectors, Tubing Head Adapters, Top Connectors, Tees/Crosses, Adapter/Spacer Spools, Flange Connectors, Threaded Connectors, Other End Connectors, Bull Plugs, Valve removal Plugs, Ring Gaskets

Machiner 10

608

Metal Ball Valves Assembler 9

Crossover Connectors, Tubing Head Adapters, Top Connectors, Tees/Crosses, Adapter/Spacer Spools, Flange Connectors, Threaded Connectors, Other End Connectors, Bull Plugs, Valve removal Plugs, Ring Gaskets

Machiner 10

609

Butterfly Valves: Double-flanged, Lug- and Wafer-type Assembler 9

Crossover Connectors, Tubing Head Adapters, Top Connectors, Tees/Crosses, Adapter/Spacer Spools, Flange Connectors, Threaded Connectors, Other End Connectors, Bull Plugs, Valve removal Plugs, Ring Gaskets

Machiner 10

650 Welded Tanks for Oil Storage –Fabricated Steel Plates and Shop Built Tanks Fabricated Steel Plates

Assembler 27