an5506-04 gpon optical network unit · pdf file32.5mm×210mm×149.1mm ... indicator...

AN5506-04

GPON Optical Network Unit

User Manual

FiberHome Telecommunication Technologies Co., Ltd.

October 2009

Thank you for choosing our products！

We appreciate your business. Your satisfaction is our

goal. We will provide you with comprehensive technical

support and after-sales service. Please contact your

local sales representative, service representative or

distributor for any help needed by one of the following

methods.

Fiberhome Telecommunication Technologies Co., Ltd.

Address: No. 5 Dongxin Rd., Hongshan Dist., Wuhan, China

Zip code: 430073

Tel: +86-27-87691549

Fax: +86-27-87691755

Website: http: //www.fiberhomegroup.com

http://www.fiberhomegroup.com

All Rights Reserved

No part of this document (including the electronic version)

may be reproduced or disseminated in any form or by any

means without prior written permission of FiberHome

Telecommunication Technologies Co., Ltd. (Hereinafter

referred to as FiberHome)

Information in this document is subject to change without

notice.

Trademarks

are trademarks of FiberHome Telecommunication Technologies Co., Ltd.

All other trademarks mentioned in this document are the property of their respective owners.

TM

TM TM

I

Operation Safety Rules

~ High optical power is harmful to human body, especially to

eyes. Never look directly into the end face of pigtail fiber of

optical transmitter or the end face of its active connector.

Α Exercise care if you must bend fibers. If necessary, the fiber

bending radius should not be less than 38 mm.

Α Power supply sockets with too heavy load or broken cables

and plugs may cause electric shock or fire. Users should

check the power supply wires and cables regularly. If there is

any breakage, please replace the cable at once.

Α Please adopt the power supply adapter provided for this

equipment. Otherwise the equipment may be damaged or not

able to run normally.

Α The equipment should be installed at positions with good

ventilation conditions and without high temperature or direct

sunshine, so as to avoid faults of the equipment and its

corresponding components due to overheat.

II

Α For communication equipment, users should note to avoid

humidification, especially prevent water from entering the

equipment. Entering of water can cause abnormal running of

the equipment and even other dangers due to short circuit.

Α Do not lay this equipment on unsteady base.

III

Packing List

After opening the packing case of AN5506-04, please check whether the

corresponding articles are in the packing case according to Packing List

as below:

Name Quantity Remark

AN5506-04 equipment 1 —

Certificate of conformity 1 —

Bag for document 1 There is an AN5506-04 GPON User

Manual.

USB storage battery power

adapter 1 Optional.

Wall-hung screws 2 For wall-hung fixation.

Contents

Operation Safety Rules ..........................................................................I

Packing List ......................................................................................... III

1 Product Introduction ......................................................................1-1

1.1 Product Functions ................................................................1-1

1.2 Technical Specifications ........................................................1-4

2 Appearance Description ................................................................2-1

2.1 Description of Upper Panel and Indicator LEDs .....................2-1

2.2 Description of Rear Panel and Interfaces ..............................2-4

3 Installation ....................................................................................3-1

3.1 Installation Preparations .......................................................3-1

3.1.1 Unpacking Check .....................................................3-1

3.1.2 Installation Precautions .............................................3-1

3.2 Fixation of Equipment ...........................................................3-2

3.2.1 Flat Fixation .............................................................3-2

3.2.2 Wall-hung Fixation ....................................................3-2

3.3 Connection of Wires and Cables ...........................................3-3

3.3.1 Connection of Network Cable....................................3-3

3.3.2 Connection of Phone Cable ......................................3-4

3.3.3 Connection of Optical Fiber .......................................3-5

3.3.4 Connection of Power Cable ......................................3-6

AN5506-04 GPON Optical Network Unit User Manual

3.4 Examination after Installation ................................................3-8

4 Frequently Asked Questions and Answers .....................................4-1

Figures

Figure 1-1 Networking diagram of AN5506-04 ..................................1-1

Figure 2-1 Elevation view of AN5506-04 upper panel.......................2-2

Figure 2-2 Elevation view of AN5506-04 rear panel ...........................2-4

Figure 3-1 Dimensions of recesses on AN5506-04 bottom panel .......3-3

Figure 3-2 Wires and cables connection (AC power) .........................3-4

Figure 3-3 Wires and cables connection (USB power) ......................3-7

Tables

Table 1-2 Technical specifications of AN5506-04............................1-4

Table 2-1 Description of AN5506-04 indicator LEDs .......................2-2

Table 2-2 Description of AN5506-04 interfaces and buttons ............2-5

1-1

1 Product Introduction

1.1 Product Functions

AN5506-04 is a kind of FTTH GPON optical network unit. It provides

communication and entertainment services in multiple modes such as data

and voice for subscribers, so as to meet integrated access demand of

families or small enterprises.

The networking diagram of AN5506-04 is shown as below:

NGN

INTERNET

CATV

GPON uplink

AN5506-04

Phone

Phone

PC

AN5516-01

Figure 1-1 Networking diagram of AN5506-04


1-2

As shown in Figure 1-1, AN5506-04 and AN5516-01 (OLT) can be used

together to compose GPON system and they can provide triple-play

multi-service access of high capacity and reliability.

Functions AN5506-04 supports are as below:

¿ Adopts GPON uplink ports, ITU-T G.984 compliant;

¿ Supports configuration functions of Ethernet interface rate, working

mode, MDI / MDIX self-adaptive mode and Pause flow control;

¿ Provides lightningproof and ESD protection functions of Ethernet

interfaces;

¿ Supports package filtering and anti-illegal message attack protection,

so as to suppress unknown unicast, broadcast and multicast

messages;

¿ Supports performance statistics function of Ethernet ports;

¿ Supports DHCP Option82 reporting the physical position information

of Ethernet interfaces;

¿ Supports PPPoE+ function for accurate subscribers identification;

¿ Supports multiple voice protocols such as H.248, MGCP and SIP;

¿ Supports IGMP Snooping and IGMP Proxy;

¿ Supports STP / RSTP protocol;

¿ Supports Layer 2 / 3 wire-speed forwarding;

¿ Downstream data in GPON system adopts triple churning algorithm

for data encryption;


1-3

¿ Supports powerful QoS function; supports global configuration of

queue priority and flexible mapping of 802.1p value of messages;

supports three scheduling modes: PQ, WRR or PQ+WRR; can

configure the weight of scheduling queue to ensure QoS of key

services such as VoIP and IPTV under multiple service conditions.


1-4

1.2 Technical Specifications

The following introduces the technical specifications of AN5506-04 (for

example) are introduced in detail as below.

Table 1-1 Technical specifications of AN5506-04

Type Item Description

Service

parameter

Voice Supports H.248, MGCP and SIP voice protocols; Adopts some voice codes such as G.711a/u, G.723 and G.729.

VLAN

Supports IEEE 802.1Q VLAN; Supports the join into 802.1Q VLAN in tag / untag mode; Supports 64 VLANs.

MAC address Supports 8k MAC addresses.

Multicast Supports IGMP Snooping and IGMP Proxy; supports IGMP V1 / V2.

QoS Supports 802.1P; supports QoS classification strategy based on ports, MAC address and VLAN ID, supports priority re-tagging.

Wire speed

layer 2 / 3

switch

All interfaces support wire speed forwarding.

Network side

interface PON interface One SC / PC interface. The maximum

transmission distance is 20km.

Subscriber

side interface

LAN interface Four RJ-45 interfaces. Supports full duplex / half duplex mode, 10 / 100Mbps self-adaption.

Phone

interface Two RJ-11 interfaces.

Mechanical

parameter

Size 32.5mm×210mm×149.1mm (Height×Width×Depth)

Weight About 650g.


1-5

Type Item Description

Power supply

parameter AC Input voltage: 220V AC.

Power

consumption

parameter

— ＜10W

Environment

parameter

Operating

temperature -10℃ to 45℃

Storage

temperature -30℃ to 60℃

Ambient

humidity 10% to 90%, non-condensing.

Note: Four Ethernet ports on AN5506-04 can not be set to the same VLAN in untag

mode. They should have different VLAN IDs.

2-1

2 Appearance Description

2.1 Description of Upper Panel and Indicator LEDs

This chapter describes AN5506-04’s appearance in detail.

The equipment body of AN5506-04 adopts hollow-carved streamline

design with novel and fashionable appearance. There are some indicator

LEDs on the upper panel indicating the running state of equipment, so

that subscribers can understand the equipment state directly.

The upper panel of AN5506-04 is shown in Figure 2-1 and the indicator

LEDs are shown in Table 2-1.


2-2

Figure 2-1 Elevation view of AN5506-04 upper panel

The description of AN5506-04 indicator LEDs is shown in Table 2-1.

Table 2-1 Description of AN5506-04 indicator LEDs

Indicator Indicator LED Color State Description

VoIP IAD state Green

On The equipment has been successfully registered to the softswitch system.

Blink A call is in progress.

Off. The equipment has not been registered to the softswitch system or not electrified.

Phone1 / 2 Phone state Green

On The subscriber has picked up the phone

Blink The phone is ringing.

Off The phone is on hook or not connected.


2-3

Indicator Indicator LED Color State Description

Power Power state Yellow-green

On

(Yellow)

The power of equipment is supplied through USB storage battery.

On

(Green) The power of equipment is supplied through AC adapter.

Off The equipment is not electrified.

PON Registration state Green

On The equipment has been registered to GPON system.

Blink An error occurs during registration.

Off The equipment has not been registered to GPON system.

LOS Optical signal state Red

On The equipment receives no optical signals.

Off The equipment receives optical signals.

LAN1/ 2 / 3 / 4 Ethernet interface

state Green

On

This interface is connected with the subscriber terminal but there is no data transmission.

Blinking This interface is transmitting or receiving data.

Off This interface is not connected with the subscriber terminal.

Battery Note Storage battery

state Green

On The storage battery runs normally.

Blinking The storage runs abnormally

(such as overlow voltage)

Off.

The power adapter of USB

storage battery is not used or

the battery fails.

Note: when AC adapter is adopted for power supply, Battery LED is off and meaningless.


2-4

2.2 Description of Rear Panel and Interfaces

All the interfaces and buttons of AN5506-04 are distributed on the rear

panel of the equipment, with a compact shape and good utility.

From left to right, on the rear panel of AN5506-04 respectively are power

switch, power interface, USB storage battery interface, 4 Ethernet

interfaces, Console interface, PON interface and two phone interfaces.

See Figure 2-2.

Figure 2-2 Elevation view of AN5506-04 rear panel


2-5

The interfaces and buttons of AN5506-04 are described in Table 2-1.

Table 2-2 Description of AN5506-04 interfaces and buttons

Interface or

Button Meaning Type Description

Power switch Button Switch on / off the power.

Power Power

interface —

Connected with the AC power

adapter.

USB

Storage

battery

interface

USB power

interface

Connected with the USB

storage battery power

adapter.

CATV CATV

interface RF

Connected with TV or set-top

box.

LAN1 to LAN4 Ethernet

interface RJ-45

Connected with PC, router

and so on.

Console

Network

interface for

local

debugging

RJ-45

For local equipment

debugging. Not open to

subscribers.

PON Optical

interface SC / PC

Connected with the optical

splitter.

Phone1 to

Phone2

Phone

interface RJ-11

Connected with the

subscriber phone.

Note: USB interface is available only in AN5506-04 adopting USB power supply

3-1

3 Installation

3.1 Installation Preparations

3.1.1 Unpacking Check

After opening the packing case of AN5506-04, please check articles in the

packing case according to Packing List. If it is found that articles in the

packing case do not comply with the list, please contact the local office of

FiberHome directly.

3.1.2 Installation Precautions

Before installing AN556-04 please ensure that the following requirements

are met:

¿ There are waterproof, moistureproof and lightningproof conditions at

the installation position.

¿ The installation position can provide conditions for AN5506-04 to

connect with the exterior. For example, there should be suitable

outlet space for power supply cable and network cable.

¿ The installation position should be able to ensure enough air flow,

convenient for cooling of the equipment.


3-2

3.2 Fixation of Equipment

AN5506-04 can be laid on a stable plane (such as a desk), or be hung on

the wall. Subscribers can select suitable installation mode on their

demand. The fixation methods of the two modes are as follows.

3.2.1 Flat Fixation

1) Take out AN5506-04 equipment from the packing case. Before

delivery, four rubber pads are pasted to four corners on the bottom of

the equipment;

2) Lay AN5506-04 on a steady desk slightly and ensure the ventilation

on both right and left sides.

3.2.2 Wall-hung Fixation

1) According to the recesses distance (170mm) marked in Figure 3-1,

fix two wall-hung screws attached to AN5506-04 into the wall.

2) Align the recesses on AN5506-04 bottom panel with the screws and

fix up slightly.

3) Let go slowly. AN5506-04 is hung on the wall with the support of

screws.

3 Installation

3-3

Figure 3-1 Dimensions of recesses on AN5506-04 bottom panel

3.3 Connection of Wires and Cables

3.3.1 Connection of Network Cable

AN5506-04 Ethernet interfaces can connect subscriber terminals such as

PCs and switches through network cables, as shown in Figure 3-2. Follow

these steps to connect the network cable:

1) Plan the wiring and cabling mode of the network cable, measure the

distance between AN5506-04 LAN interface and the subscriber

terminal, and select the network cable with a suitable length;

2) Fix the network cable and then make Ethernet connectors for both

ends;

3) Connect Ethernet connector of one end to a certain AN5506-04 LAN

interface;


3-4

4) Connect Ethernet connector of the other end to an Ethernet interface

on a PC or a switch;

5) The connection of the network cable is finished. ? Note 1: transmission distance of the network cable is less than 100m.

Therefore length of the network cable prepared by the subscriber should

not exceed 100m.

? Note 2: AN5506-04 Ethernet interface supports MDI / MDIX self-adaption.

Either straight-through network cable or cross-over network cable is

suitable for cabling.

AC power adapter

Mains Supply

PC

PCPC

Optical Splitter

Phone Phone

Switch

Figure 3-2 Wires and cables connection (AC power)

3.3.2 Connection of Phone Cable

AN5506-04 offers two phone interfaces to provide voice services for

subscribers, as shown in Figure 3-2. Follow these steps to connect the

voice cable:

3 Installation

3-5

1) Plan the wiring and cabling mode of the phone cable, measure the

distance between AN5506-04 Phone interface and the subscriber

phone, and select the phone cable with a suitable length;

2) Fix the phone cable and then make RJ-11 connectors for both ends;

3) Connect one end of the phone cable to a certain AN5506-04 Phone

interface;

4) Connect the other end to a subscriber phone;

5) The connection of the phone cable is finished.

3.3.3 Connection of Optical Fiber

AN5506-04 adopts wavelength division multiplexing (WDM) mode and

provides “triple-play” integrated access, as shown in Figure 3-2. The

connection steps of optical fibers are as below:

1) Plan the wires and cables layout mode of the optical fiber; measure

the distance between AN5506-04 PON interface and upstream

optical splitter; select the optical jumper with suitable length;

2) Fix the optical fiber; remove the protection covers of the optical

jumper and AN5506-04 optical interface;

3) Insert one end of the optical jumper into AN5506-04 PON interface

slightly;

4) Connect the other end of the optical jumper with the optical splitter;

5) The connection of optical fibers is finished.

Α Caution 1: if the optical fiber jumpers are not used, make sure

optical fiber jumpers and AN5506-04 optical interfaces are

covered to avoid dust contamination and water penetration,

which lead to the uselessness of optical fiber jumpers and

AN5506-04 optical interfaces.


3-6

Α Caution 2: connect optical fibers at last if possible. Lay

optical fibers at the position without extrusion.

3.3.4 Connection of Power Cable

AN5506-04 allows two modes of power supply: AC power and USB

storage battery. Their connections are introduced below respectively.

AC Power Connection

1) Take out the provided AC power adapter;

2) Connect one end of the adapter to Power interface of AN5506-04;

3) Connect the other end to mains supply socket, as shown in Figure

3-2;

4) The connection of power cable is finished. ? Note: This power adapter can convert 220V AC into 12V DC input for

AN5506-04 so as to supply power to the equipment.

USB Storage Battery Power Connection

USB storage battery power adapter integrates a DC storage battery which

serves as a standby power supply and enables the equipment to keep

running for 6 to 7 hours in the case of power failure. It lifts operational

reliability of the equipment. Follow these steps to connect the power

cable.

1) Take out the provided USB storage battery power adapter;

2) Connect one end of the adapter to USB power interface on

AN5506-04;

3) Connect the other end to mains supply socket, as shown in Figure

3-3;

4) The connection of power cable is finished.

3 Installation

3-7

? Note: USB storage battery power adapter has a Battery LED. When the

storage battery is being recharged, it is lit red. When battery recharging is

finished, it is lit green.

USB storage battery power

adapter

Mains Supply

PC

PCPC

Optical Splitter

Phone Phone

Switch

Figure 3-3 Wires and cables connection (USB power)

Α Caution: in practical applications, select one of the above two

connection modes only. Connecting both Power interface

and USB interface to power supplies is strictly prohibited lest

dangers may occur due to short circuit.


3-8

3.4 Examination after Installation

After the connection of wires and cables is finished and relevant services

are started up by the operator, it needs to power on and examine

AN5506-04 as below:

1) Switch on the power.

2) Observe the status of Power indicator LED. If Power indicator LED

is ON, it means the power-on of equipment is normal; otherwise,

please check whether the connection of power cable is correct.

3) If USB storage battery is adopted for power supply, subscribers

should observe the status of Battery indicator LED. If Battery

indictor LED is ON, it means the power cable of USB storage battery

is connected normally; otherwise, check whether the connection of

USB storage battery power cable is correct.

4) Observe the status of LOS indicator LED. If LOS indicator LED is

OFF, it means the optical fiber connection is normal; otherwise,

please check whether the connection of optical fibers is correct.

5) Observe the status of LAN indicator LED. If LAN indicator LED is

ON or blinks, it means the network cable is connected normally;

otherwise, please check whether the connection of network cable is

correct.

6) Observe the status of Phone indicator LED. If before and after the

phone is picked up, Phone indicator LED turns OFF to ON, it means

the phone cable is connected normally; otherwise, please check

whether the connection of phone cable is correct.

7) Ensure the ventilation around during equipment running to avoid

problems because of overheating. Check the running status of the

fan at any moment. For abnormity, contact the local office of

FiberHome for replacement, so as not to affect equipment running.

4-1

4 Frequently Asked Questions and Answers

Q: All indicator LEDs are OFF after power-on.

A: 1) Check whether the power connection cable is connected well;

2) Check whether the power switch on the equipment front panel is ON.

Q: The equipment fails to work after a period of normal running.

A: 1) If the equipment works abnormally, check whether the power is connected normally or the voltage is over high or over low;

2) The equipment has over-heat fault. Check whether the ventilation is normal and check whether there is direct sunshine or heat source around.

Q: LOS indicator LED is ON.

A: 1) The optical fiber is faulty. Check whether the optical fiber is connected normally and whether it is connected to correct interface;

2) The upstream equipment is faulty;

3) The optical power is out of the normal range (such as overload).

Q: Battery indicator LED blinks or turns OFF.

A: 1) If Battery indicator LED blinks, it means that the battery works abnormally or the voltage is over low. Recharge it in time;


4-2

2) If Battery indicator LED turns OFF, check whether USB power cable is connected normally;

3）If Battery indicator LED turns OFF, check whether the storage battery expires or has faults.

Q: LAN indicator LED is OFF.

A: 1) Check whether the network cable is damaged or its connection is loose;

2) Check whether the network cable is made correctly. If it is incorrect, replace it with a new network cable made according to the standard method (for making a CAT 5 twisted-pair cable);

3) Check whether the network cable length exceeds allowable range.

FFeeeeddbbaacckk FFoorrmm

Your feedback is an important way for us to receive questions, comments and suggestions...ultimately providing you with enhanced manuals and services by FiberHome.

1. Please give your opinions on the items listed below about this manual by the symbol “√”.

Items Excellent Good Normal Bad

Expression £ £ £ £

Integrity £ £ £ £

Exactitude £ £ £ £

Structure £ £ £ £

Illustration £ £ £ £

Getup £ £ £ £

General £ £ £ £

2. Please give your advices on the items listed below about this manual by the symbol “√”.

£ Adjust its structure £ Contents more detailed

£ Give more examples £ Expression more concise

£ Add more illustrations £ Operationality more ascensive

Please give more details of your advices on this manual:

3. Which part of this manual do you appreciate more?

4. Other advices for our manuals:

5. The personal information requested is used for no other purposes than to respond to your feedback

Name Job/Position Working Unit E-mail Correspondence Phone Num Correspondence Facsimile Correspondence Address Date

FiberHome Telecommunication Technologies Co., Ltd.

Address: No. 5 Dongxin Rd., Hongshan Dist., Wuhan, China

Zip code: 430073

Tel: +86-27-87691549

Fax: +86-27-87691755

Website: http://www.fiberhomegroup.com

http://www.fiberhomegroup.com

an5506-04 gpon optical network unit · pdf file32.5mm×210mm×149.1mm ... indicator...

Documents