agilent msd

Download Agilent MSD

Post on 31-Aug-2014

295 views

Category:

Documents

2 download

Embed Size (px)

TRANSCRIPT

5975 Series Mass Selective Detectors

Hardware Installation

Agilent Technologies

Notices Agilent Technologies, Inc. 2010 No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Agilent Technologies, Inc. as governed by United States and international copyright laws.

Safety Notices

CAUTIONA CAUTION notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in damage to the product or loss of important data. Do not proceed beyond a CAUTION notice until the indicated conditions are fully understood and met.

Manual Part NumberG3170-90038

EditionSecond edition, February 2010 Printed in USA Agilent Technologies, Inc. 5301 Stevens Creek Boulevard Santa Clara, CA 95052

WA R N I N GAcknowledgementsMicrosoft and Windows are U.S. registered trademarks of Microsoft Corporation.

A WARNING notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in personal injury or death. Do not proceed beyond a WARNING notice until the indicated conditions are fully understood and met.

2

Hardware Installation

Contents1 General Information Introduction 8

Important Safety Warnings 11 Many internal parts of the MSD carry dangerous voltages 11 Electrostatic discharge is a threat to MSD electronics 11 Many parts are dangerously hot 12 Hydrogen 12 Safety and Regulatory Certifications 14 Information 14 Symbols 15 Electromagnetic compatibility 16 Sound emission declaration for Germany Cleaning 17 17 18

16

Recycling the Product

Customer Responsibilities Before You Start 19 20

Other Documentation 2 Installation Overview 22

Unpacking and Inspecting the Materials Installing the GC 24

23

Connecting the Helium Lines to the GC Configuring the GCHardware Installation

26

283

Conditioning the Column

29 30

Preparing the MSD for Installation Preparing the Vacuum System 31

Plumbing the Methane Line to the CI MSD Flow Module Connecting the MSD and the GC Installing the ChemStation PC 39 36

34

Verifying EI System Performance 40 Verify the tune performance 40 Verify the sensitivity performance 40 Switching from EI to CI Operating Mode Verifying CI System Performance Verify PCI performance 42 Verify NCI performance 42 42 41

Verifying High Mass System Performance Familiarizing the Customer 3 Checklists 44

43

Installation Checklist 46 Verifying that site preparation is complete 46 Unpacking and inspecting the shipped materials GC installation 47 MSD installation 48 MSD ChemStation PC installation 50 Performance verification 50 Instrument Log Book updated 52 Customer Familiarization Checklist 53 Topics not included in familiarization Hardware overview 54 System operation 54 53

46

4

Hardware Installation

MSD ChemStation software overview 54 MSD ChemStation software autotune descriptions Methods 55 Data acquisition 55 Data analysis 55 Sequence 56 MSD ChemStation maintenance 56 EI instrument user maintenance 56 Troubleshooting (Diagnostics) 57 Tune charts 57 Additional support information 57

54

Hardware Installation

5

6

Hardware Installation

5975 Series Mass Selective Detectors Hardware Installation

1 General InformationIntroduction 8 Important Safety Warnings 11 Safety and Regulatory Certifications 14 Cleaning 17 Recycling the Product 17 Customer Responsibilities 18 Before You Start 19 Other Documentation 20

This section provides information on how to identify specifically what type of MSD you are working with as well as how to properly clean and dispose of the instrument. Also included in this section are the Important Safety Warnings which list critical safety precautions for all users.

Agilent Technologies

7

1

General Information

IntroductionThis document provides installation instructions for the Agilent Technologies 5975 Series Mass Selective Detector (MSD). Installation must be performed by an Agilent Technologies service representative. The Agilent Technologies 5975 Series Mass Selective Detectors (MSDs) are diffusion and turbo pump MSDs. The 5975 Series MSD system consists of: Mix and match of the combinations below may not be supported.

NOTE

5975 Series MSD Optional G3397A High Vacuum Gauge controller (required for CI operation) Gas Chromatograph Series 6890 and 6850 Series GC, with options for MSD use 7890A Series GC, with options for MSD use 7820A Series GC, predefined bundles for the MSD use ALS Autosamplers 7683 Series Automatic Liquid Sampler 7693 Series Automatic Liquid Sampler Computer and MSD ChemStation software Refer to your MSD ChemStation documentation for additional information Table 1 lists possible configurations for the 5975 Series MSD. Figure 1 identifies many of the common parts.

8

Hardware Installation

General Information

1

Table 1Model name

Available high vacuum pumpsProduct number G3170A G3171A G3172A Description Diffusion Pump MSD Standard Turbo MSD Performance Turbo MSD Ionization modes Electron impact (EI) Electron impact (EI) Electron impact (EI)

5975C TAD VL MSD 5975C TAD inert MSD 5975C TAD inert XL MSD 5975C TAD inert XL MSD 7820 VL MSD 7820 MSD

G3174A

CI High Mass Performance Turbo Pump Diffusion Pump MSD Standard Turbo MSD

Electron impact (EI) Negative chemical ionization (NCI) Positive chemical ionization (PCI) Electron impact (EI) Electron impact (EI)

G3175A G3176A

Hardware Installation

9

1

General Information

ALS

7890A GC

CI gas flow module

Local control panel

5975 Series MSD MSD power switch

GC power switch

Figure 1

5975 Series MSD system

10

Hardware Installation

General Information

1

Important Safety WarningsBefore moving on, there are several important safety notices that you should always keep in mind when using the 5975 Series MSD.

Many internal parts of the MSD carry dangerous voltagesIf the MSD is connected to a power source, even if the power switch is off, potentially dangerous voltages exist on the wiring between the MSD power cord and the AC power supply, the AC power supply itself, and the wiring from the AC power supply to the power switch. With the power switch on, potentially dangerous voltages also exist on: All electronics boards in the instrument. The internal wires and cables connected to these boards. The wires for any heater (oven, detector, inlet, or valve box).

WA R N I N G

All these parts are shielded by covers. With the covers in place, it should be difficult to accidentally make contact with dangerous voltages. Unless specifically instructed to, never remove a cover unless the detector, inlet, or oven are turned off.

WA R N I N G

If the power cord insulation is frayed or worn, the cord must be replaced. Contact your Agilent service representative.

Electrostatic discharge is a threat to MSD electronicsThe printed circuit (PC) boards in the MSD can be damaged by electrostatic discharge. Do not touch any of the boards unless it is absolutely necessary. If you must handle them, wear a grounded wrist strap and take other antistatic precautions. Wear a grounded wrist strap any time you must remove the MSD right side cover.

Hardware Installation

11

1

General Information

Many parts are dangerously hotMany parts of the MSD operate at temperatures high enough to cause serious burns. These parts include but are not limited to: The inlets The oven and its contents The detectors The column nuts attaching the column to an inlet or detector The valve box You should always cool these areas of the MSD to room temperature before working on them. They will cool faster if you first set the temperature of the heated zone to room temperature. Turn the zone off after it has reached the setpoint. If you must perform maintenance on hot parts, use a wrench and wear gloves. Whenever possible, cool the part of the instrument that you will be maintaining before you begin working on it.

WA R N I N G

Be careful when working behind the instrument. During cool-down cycles, the MSD emits hot exhaust which can cause burns.

WA R N I N G

The insulation around the inlets, detectors, valve box, and the insulation cups is made of refractory ceramic fibers. To avoid inhaling fiber particles, we recommend the following safety procedures: ventilate your work area; wear long sleeves, gloves, safety glasses, and a disposable dust/mist respirator; dispose of insulation in a sealed plastic bag; wash your hands with mild soap and cold water after handling the insulation.

HydrogenHydrogen gas may be used as carrier gas, and/or as fuel for the FID. When mixed with air, hydrogen can form explosive mixtures.

12

Hardware Installation

General Information

1

WA R N I N G

When using hydrogen (H2) as the carrier gas or fuel gas, be aware that hydrogen gas can flow into the oven and create an explosion hazard. Therefore, be sure that the supply is off until all connections are made, and ensure that the inlet and detector column fittings are either connected to a column or capped at all times when hydrogen gas is supplied to the instrument. Hydrogen is flammable. Leaks, when confined in an enclosed space, may create a fire or e

Recommended

View more >