1 1 8544096 GLIDERAIL ASSY6.5',JIB RAIL2 2 8544100 WELDMENT,GUSSET,JIB SUPPORT,6.5'OFFSET3 1 ---------- UPRIGHT ASSEMBLY4 1 8545007 WELDMENT,BOLT,1-8X20.75,ZP,GR B75 2 8513789 WASHER,FLAT,1,W,ZP6 1 8522156 NUT,LOCK,1,NYLONG

ITEM QTY PART NO. DESCRIPTION

COMPONENTS LIST

THIS DRAWING AND THE INFORMATION CONTAINEDHEREIN IS AND SHALL REMAIN THE PROPERTY OFCAPITAL SAFETY, AND CANNOT BE USED ORREPRODUCED WITHOUT PERMISSION. ANY MATERIALAND/OR PART SUBSTITUTIONS AND/OR CHANGESMUST BE AUTHORIZED IN WRITING BY CAPITALSAFETY PRIOR TO USE.

Capital Safety3833 SALA WayRED WING, MN 55066-5005651-388-8282SCALE -------- PROE www.capitalsafety.com

TITLE EMU JIB ASSEMBLYINSTRUCTION

DO NOT SCALEDRAWING

DRAWING NUMBER REVISION

5903390 B

TOOLS REQUIRED1-1/2 SOCKET AND WRENCH

1-1/8 SOCKET

1-1/16 WRENCH

3/4" SOCKET AND WRENCH

TORQUE WRENCH

ADJUSTABLE HEIGHT JIB ASSEMBLY FOR MODEL #'S8530557, 8530558, & 8530559

STEP 1 - UNCRATE AND IDENTIFY ALL OF THECOMPONENTS IN THE COMPONENTS LIST.

STEP 2 - POSITION ITEM 3 ON ITS SIDE ANDSPACE IT OFF THE GROUND WITH A SPACERAS SHOWN.

NOTE: ITEM 3 HAS A LIFTINGRING FOR POSITIONING VIACRANE OR FORKLIFT

STEP 3 - ATTACH ITEM 1 TO ITEM 3. FINGERTIGHTEN HARDWARE. FINAL TIGHTENINGOF HARDWARE IN STEP 5.

STEP 4 - USE THE ITEM 2'S TO CONNECT THE ITEM 1TO ITEM 3. FINGER TIGHTEN HARDWARE. FINALTIGHTENING OF HARDWARE IN STEP 5.

STEP 5 - FINAL TORQUE THECONNECTING HARDWARE TOTHE SPECIFICATIONS BELOW.

3.

1.

2.

4.

5.

6. 1. 3. 3/4" HARDWARE

3. 1.

4. 5.

5. 6.

2.

1/2" HARDWARE

130 ft*lbs [176 Nm]

60 ft*lbs [81 Nm]

175 ft*lbs [237 Nm]

THIS DRAWING AND THE INFORMATION CONTAINEDHEREIN IS AND SHALL REMAIN THE PROPERTY OFCAPITAL SAFETY, AND CANNOT BE USED ORREPRODUCED WITHOUT PERMISSION. ANY MATERIALAND/OR PART SUBSTITUTIONS AND/OR CHANGESMUST BE AUTHORIZED IN WRITING BY CAPITALSAFETY PRIOR TO USE.

Capital Safety3833 SALA WayRED WING, MN 55066-5005651-388-8282SCALE -------- PROE www.capitalsafety.com

TITLE EMU JIB ASSEMBLYINSTRUCTION

DO NOT SCALEDRAWING

DRAWING NUMBER REVISION

5903390 B

TOOLS REQUIRED3/4 SOCKET

3/4 WRENCH

TORQUE WRENCH1 1 8545771 OFFSET ARM,ASSEMBLY,FIXED HEIGHT EMU2 1 8545774 UPRIGHT,ASSEMBLY,FIXED HEIGHT EMU

ITEM QTY PART NO. DESCRIPTION

COMPONENTS LIST

2.

1.

1.

2.

FIXED HEIGHT JIB ASSEMBLY FOR MODEL #'S8530571

STEP 1 - UNCRATE AND IDENTIFY ALL OF THECOMPONENTS IN THE COMPONENTS LIST.

STEP 2 - ATTACH ITEM 1 TO ITEM 2. TORQUEALL HARDWARE TO 60 FT*LBS [81 N*m].

SCALE 0.050

SEE DETAIL A

SEE DETAIL B

NOTE: ITEM 1 HAS A LIFTINGRING FOR POSITIONING VIACRANE OR FORKLIFT

DETAIL ASCALE 0.250

4X 1/2" HARDWARE