ademco 15p-20p installation

Download ademco 15P-20P installation

Post on 28-Oct-2015

162 views

Category:

Documents

0 download

Embed Size (px)

DESCRIPTION

installation and programming documentation for the Vista 15P-20P security panels.

TRANSCRIPT

  • ON OFF

    1 OFF

    4 MAX

    7 INSTANT

    READY

    2 AWAY

    5 TEST

    8 CODE

    0

    3 STAY

    6 BYPASS

    9 CHIME

    #

    ARMED

    READY

    1 OFF4 MAX7 INSTANT

    READY

    2 AWAY5 TEST8 CODE0

    3 STAY6BYPASS9CHIME#

    ARMED

    READY

    K5305-1V1 4/02

  • RECOMMENDATIONS FOR PROPER PROTECTION

    The Following Recommendations for the Location of Fire and Burglary DetectionDevices Help Provide Proper Coverage for the Protected Premises.

    Recommendations For Smoke And Heat DetectorsWith regard to the number and placement of smoke/heat detectors, we subscribe to the recommendationscontained in the National Fire Protection Association's (NFPA) Standard #72 noted below.

    Early warning fire detection is best achieved by the installation of fire detection equipment in all roomsand areas of the household as follows: For minimum protection a smoke detector should be installedoutside of each separate sleeping area, and on each additional floor of a multi-floor family living unit,including basements. The installation of smoke detectors in kitchens, attics (finished or unfinished), or ingarages is not normally recommended.

    For additional protection the NFPA recommends that you install heat or smoke detectors in the livingroom, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms,basements and attached garages.

    In addition, we recommend the following:

    Install a smoke detector inside every bedroom where a smoker sleeps.

    Install a smoke detector inside every bedroom where someone sleeps with the door partly orcompletely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outsidemay not wake up the sleeper if the door is closed.

    DININGKITCHEN

    BEDROOM

    BEDROOM

    BEDROOM

    BEDROOM

    LIVING ROOM

    BEDROOM

    BDRM

    BDRM

    DINING

    LIVING ROOM

    TV ROOM KITCHEN

    BEDROOM BEDROOM

    TOBR

    LVNG RM

    BASEMENT

    KTCHN

    .CLOSEDDOOR

    GARAGE

    Smoke Detectors for Minimum ProtectionSmoke Detectors for Additional ProtectionHeat-Activated Detectors

    Install a smoke detector inside bedroomswhere electrical appliances (such asportable heaters, air conditioners orhumidifiers) are used.

    Install a smoke detector at both ends of ahallway if the hallway is more than 40feet (12 meters) long.

    Install smoke detectors in any room wherean alarm control is located, or in any roomwhere alarm control connections to an ACsource or phone lines are made. Ifdetectors are not so located, a fire withinthe room could prevent the control fromreporting a fire or an intrusion.

    THIS CONTROL COMPLIES WITH NFPAREQUIREMENTS FOR TEMPORAL PULSESOUNDING OF FIRE NOTIFICATIONAPPLIANCES.

    Recommendations For Proper Intrusion ProtectionFor proper intrusion coverage, sensors should be located at every possible point of entry to a home orcommercial premises. This would include any skylights that may be present, and the upper windows ina multi-level building.

    In addition, we recommend that radio backup be used in a security system so that alarm signals canstill be sent to the alarm monitoring station in the event that the telephone lines are out of order (alarmsignals are normally sent over the phone lines, if connected to an alarm monitoring station).

    ii

  • Table Of Contents

    Section 1. Features and Installation Highlights........................................................................................ 1-1Capabilities ....................................................................................................................................................................... 1-1Functions ........................................................................................................................................................................... 1-1Compatible Devices........................................................................................................................................................... 1-2Important Installation Highlights (Installer Please Read) ............................................................................................ 1-2

    Section 2. Mounting and Wiring the Control.............................................................................................. 2-1Cabinet and Lock .............................................................................................................................................................. 2-1Mounting the PC Board Alone ......................................................................................................................................... 2-1Mounting Board with RF Receiver................................................................................................................................... 2-2Wiring to Keypads............................................................................................................................................................. 2-3Sounder (Bell) Connections .............................................................................................................................................. 2-4Wiring the AC Transformer.............................................................................................................................................. 2-4Backup Battery ................................................................................................................................................................. 2-5Earth Ground .................................................................................................................................................................... 2-5Hardwire Zones ................................................................................................................................................................. 2-6Double Balanced Zones ................................................................................................................................................... 2-6Zone Doubling ................................................................................................................................................... 2-6Smoke Detectors................................................................................................................................................................ 2-64219/4229 Expansion Zones ............................................................................................................................................. 2-7Installing the RF Receiver................................................................................................................................................ 2-8Installing a 5800TM Module ............................................................................................................................................ 2-8Installing the Transmitters .............................................................................................................................................. 2-8Installing a Keyswitch ...................................................................................................................................................... 2-9Connecting Relay Modules ............................................................................................................................................. 2-10Powerline Carrier Devices .............................................................................................................................................. 2-11On-Board Triggers .......................................................................................................................................................... 2-11Phone Line/Phone Module Connections......................................................................................................................... 2-12Long Range Radio Connections...................................................................................................................................... 2-13AAV Connections ............................................................................................................................................................ 2-13

    Section 3. Programming Overview ............................................................................................................... 3-1About Programming.......................................................................................................................................................... 3-1Zones and Partitions ......................................................................................................................................................... 3-1Keypads ............................................................................................................................................................................. 3-2Wireless Receiver and Transmitters................................................................................................................................ 3-2Pager Programming .......................................................................................................................................................... 3-2Function Keys.................................................................................................................................................................... 3-3Output Devices.................................................................................................................................................................. 3-3Zone Type Definitions ...........................................................