2


l Upon completion of this course, you will be able to:

[Describe the access counters

[Know access KPI


Chapter 1 RRC Establishment Counter and KPI Chapter 1 RRC Establishment Counter and KPI

Chapter 2 Security Mode Counter and KPIChapter 2 Security Mode Counter and KPI

Chapter 3 RAB Assignment Counter and KPIChapter 3 RAB Assignment Counter and KPI

Chapter 4 RB Counter and KPIChapter 4 RB Counter and KPI

3


RRC Establishment Counter and KPIl RRC Connection Setup Cause

Emergency CallVS.RRC.AttConnEstab.EmgTerminating Background CallVS.RRC.AttConnEstab.TrmBkgTerminating Interactive CallVS.RRC.AttConnEstab.TrmIntTerminating Streaming CallVS.RRC.AttConnEstab.TrmStrTerminating Conversational CallVS.RRC.AttConnEstab.TrmConvOriginating Subscribed traffic CallVS.RRC.AttConnEstab.OrgSubsOriginating Background CallVS.RRC.AttConnEstab.OrgBkgOriginating Interactive CallVS.RRC.AttConnEstab.OrgIntOriginating Streaming CallVS.RRC.AttConnEstab.OrgStrOriginating Conversational CallVS.RRC.AttConnEstab.OrgConvExplanationCounters (RNC)



Cause unknownVS.RRC.AttConnEstabab.UnknownUESBI-Uu informationVS.RRC.AttConn.UESBI.UUTerminating Low Priority SignalingVS.RRC.AttConnEstab.TmLPSiTerminating High Priority SignalingVS.RRC.AttConnEstab.TmHPSiCall re-establishmentVS.RRC.AttConnEstab.RestOriginating Low Priority SignalingVS.RRC.AttConnEstab.OgLPSigOriginating High Priority SignalingVS.RRC.AttConnEstab.OrgHPSiDetachVS.RRC.AttConnEstab.DetachRegistration VS.RRC.AttConnEstab.RegInter-RAT cell re-selectionVS.RRC.AttConnEstab.CellResExplanationCounters (RNC)

4



Emergency CallRRC.AttConnEstab.EmgCallTerminating Background CallRRC.AttConnEstab.TmBkgCallTerminating Interactive CallRRC.AttConnEstab.TmInterCallTerminating Streaming CallRRC.AttConnEstab.TmStrCallTerminating Conversational CallRRC.AttConnEstab.TmConvCallOriginating Subscribed traffic CallRRC.AttConnEstab.OgSubCallOriginating Background CallRRC.AttConnEstab.OrgBkgCallOriginating Interactive CallRRC.AttConnEstab.OrgInterCallOriginating Streaming CallRRC.AttConnEstab.OrgStrCallOriginating Conversational CallRRC.AttConnEstab.OrgConvCallExplanationCounters (Cell)



Cause unknownRRC.AttConnEstab.UnknownTerminating Low Priority SignalingRRC.AttConnEstab.TmLwPrSigTerminating High Priority SignalingRRC.AttConnEstab.TmHhPrSigCall re-establishmentRRC.AttConnEstab.CallReEstOriginating Low Priority SignalingRRC.AttConnEstab.OgLwPrSig

Originating High Priority SignalingRRC.AttConnEstab.OgHhPrSig

DetachRRC.AttConnEstab.IMSIDetachRegistration RRC.AttConnEstab.RegInter-RAT cell change orderRRC.AttConnEstab.IRATCCOInter-RAT cell re-selectionRRC.AttConnEstab.IRATCelResExplanationCounters (Cell)

5


RRC Establishment Counter and KPI

l RRC Establishment

[ RRC connection request

− Establishment request for different reasons

[ RRC connection setup

− Established on different channels

[ RRC connection setup complete

− Setup complete for different services

− Setup complete on different channels

[ RRC connection reject

− Reject due to congestion


RRC Establishment Counter

l RRC connection request[ Number of RRC connection request: VS.RRC.AttConnEstab (RNC) at point A2

6



l RRC connection request (RNC)[ VS.RRC.AttConnEstab.OrgConv

[ VS.RRC.AttConnEstab.OrgStr

[ VS.RRC.AttConnEstab.OrgInt

[ VS.RRC.AttConnEstab.OrgBkg

[ VS.RRC.AttConnEstab.OrgSubs

[ VS.RRC.AttConnEstab.TrmConv

[ VS.RRC.AttConnEstab.TrmStr

[ VS.RRC.AttConnEstab.TrmInt

[ VS.RRC.AttConnEstab.TrmBkg

[ VS.RRC.AttConnEstab.Emg

[ VS.RRC.AttConnEstab.CellRes

[ VS.RRC.AttConnEstab.Reg

[ VS.RRC.AttConnEstab.Detach

[ VS.RRC.AttConnEstab.OrgHPSig

[ VS.RRC.AttConnEstab.OrgLPSig

[ VS.RRC.AttConnEstab.Rest

[ VS.RRC.AttConnEstab.TmHPSig

[ VS.RRC.AttConnEstab.TmLPSig

[ VS.RRC.AttConn.UESBI.UU

[ VS.RRC.AttConnEstab.Unknown



l RRC connection request (Cell)[ RRC.AttConnEstab.OrgConvCall

[ RRC.AttConnEstab.OrgStrCall

[ RRC.AttConnEstab.OrgInterCall

[ RRC.AttConnEstab.OrgBkgCall

[ RRC.AttConnEstab.OgSubCall

[ RRC.AttConnEstab.TmConvCall

[ RRC.AttConnEstab.TmStrCall

[ RRC.AttConnEstab.TmInterCall

[ RRC.AttConnEstab.TmBkgCall

[ RRC.AttConnEstab.EmgCall

[ RRC.AttConnEstab.IRATCelRes

[ RRC.AttConnEstab.IRATCCO

[ RRC.AttConnEstab.Reg

[ RRC.AttConnEstab.IMSIDetach

[ RRC.AttConnEstab.OgHhPrSig

[ RRC.AttConnEstab.OgLwPrSig

[ RRC.AttConnEstab.CallReEst

[ RRC.AttConnEstab.TmHhPrSig

[ RRC.AttConnEstab.TmLwPrSig

[ RRC.AttConnEstab.Unknown

7



l RRC connection setup[ RRC connection setup: VS.RRC.SetupConnEstab (RNC) at point B

[ RRC connection setup on DCH: VS.RRC.SetupConnEstab.DCH (RNC) at point B

[ RRC connection setup: VS.RRC.SetupConnEstab.Cell (Cell) point B



l RRC connection setup Complete[ VS.RRC.SuccConnEstab (RNC)at point C

− VS.RRC.SuccConnEstab.DCH (RNC)

− VS.RRC.SuccConnEstab.CCH (RNC)

[ VS.RRC.SuccConnEstab.Cell (Cell) at point C

− VS.RRC.SuccConEst.DCH (Cell)

− VS.RRC.SuccConEst.CCH (Cell)

8



l RRC connection setup Complete (RNC)[ VS.RRC.SuccConnEstab.OrgConv

[ VS.RRC.SuccConnEstab.OrgStr

[ VS.RRC.SuccConnEstab.OrgInt

[ VS.RRC.SuccConnEstab.OrgBkg

[ VS.RRC.SuccConnEstab.OrgSubs

[ VS.RRC.SuccConnEstab.TrmConv

[ VS.RRC.SuccConnEstab.TrmStr

[ VS.RRC.SuccConnEstab.TrmInt

[ VS.RRC.SuccConnEstab.TrmBkg

[ VS.RRC.SuccConnEstab.Emg

[ VS.RRC.SuccConnEstab.CellRes

[ VS.RRC.SuccConnEstab.Reg

[ VS.RRC.SuccConnEstab.Detach

[ VS.RRC.SuccConnEstab.OrgHPSi

[ VS.RRC.SuccConnEstab.OgLPSig

[ VS.RRC.SuccConnEstab.Rest

[ VS.RRC.SuccConnEstab.TmHPSi

[ VS.RRC.SuccConnEstab.TmLPSi

[ VS.RRC.SuccConn.UESBI.UU

[ VS.RRC.SuccConnEstab.Unknown



l RRC connection setup Complete (Cell)[ RRC.SuccConnEstab.OgConvCall

[ RRC.SuccConnEstab.OrgStrCall

[ RRC.SuccConnEstab.OrgItrCall

[ RRC.SuccConnEstab.OrgBkgCall

[ RRC.SuccConnEstab.OrgSubCall

[ RRC.SuccConnEstab.TmConvCall

[ RRC.SuccConnEstab.TmStrCall

[ RRC.SuccConnEstab.TmItrCall

[ RRC.SuccConnEstab.TmBkgCall

[ RRC.SuccConnEstab.EmgCall

[ RRC.SuccConnEstab.IRATCelRes

[ RRC.SuccConnEstab.IRATCCO

[ RRC.SuccConnEstab.Reg

[ RRC.SuccConnEstab.IMSIDetach

[ RRC.SuccConnEstab.OgHhPrSig

[ RRC.SuccConnEstab.OgLwPrSig

[ RRC.SuccConnEstab.CallReEst

[ RRC.SuccConnEstab.TmHhPrSig

[ RRC.SuccConnEstab.TmLwPrSig

[ RRC.SuccConnEstab.Unkown

9


l RRC Connection establishment

[ RRC.FailConnEstab.NoReply:

− The measurement is triggered when the RNC does not receive the RRC

CONNECT SETUP COMPLETE messages upon sending of RRC CONNECT

SETUP messages. The RNC takes statistics by cells the UE camps on

− Cell level

RRC Establishment CounterOther related CountersOther related Counters


l RRC Connection reject

[ VS.RRC.Rej.RL.Fail

− Radio link failure

[ VS.RRC.Rej.AAL2.Fail

− AAL2 setup failure


10


l RRC Connection reject

[ RRC.FailConnEstab.Cong ; VS.RRC.FailConEst.Cng.RNC

− Number of RRC CONNECTION REJECT messages from the RNC to UEs in a

cell due to network congestion after receiving RRC CONNECTION REQUEST messages from the UEs

[ Numbers of RRC Connection Rejects due to Radio Resource Congestion (Cell)

− VS.RRC.Rej.Power.Cong :Power resource request failure

− VS.RRC.Rej.UL.CE.Cong :Code resource request failure

− VS.RRC.Rej.DL.CE.Cong :Cell UL resource request failure

− VS.RRC.Rej.Code.Cong :Cell DL resource request failure



l RRC Setup Success Rate

[Formula

[Measurement scope:

− RNC & Cell

[Description

− This KPI can be used to evaluate RRC setup success ratio about CS service, PS service and other reasons.

%100*_ionAttemptRRCConnectionSuccessRRCConnectSRRRCS =

RRC Establishment KPI

11



l RRC Setup Success Rate (CS)

[ Counters (RNC)

− : VS.RRC.AttConnEstab.Cause

− : VS.RRC.SuccConnEstab.Cause

[ Counters (Cell)

− : RRC.AttConnEstab.Cause

− : RRC.SuccConnEstab.Cause

[ For example, the causes could be

− For RNC: OrgConv, OrgSubs, TrmConv, Rest, Emg, Unknown

− For Cell: OgConvCall, OrgSubCall, TmConvCall, CallReEst, EmgCall, Unkow

csionSuccessRRCConnectcsionAttemptRRCConnect

csionSuccessRRCConnectcsionAttemptRRCConnect



l RRC Setup Success Rate (PS)

[ Counters (RNC)

− : VS.RRC.AttConnEstab.cause

− : VS.RRC.SuccConnEstab.cause

[ Counters (Cell)

− :RRC.AttConnEstab.cause

− :RRC.SuccConnEstab.cause

[ For example, the cause could be

− For RNC: OrgInt, OrgBkg, TrmInt, TrmBkg, OrgHPSi, TmHPSi

− For Cell: OrgItrCall, OrgBkgCall, TmItrCall, TmBkgCall, OgHhPrSig, TmHhPrSig

psionAttemptRRCConnect

psionSuccessRRCConnect

psionAttemptRRCConnect

psionSuccessRRCConnect

12



l RRC Setup Success Rate (Inter RAT Cell reselection)

[Counters (RNC)

− : VS.RRC.AttConnEstab.CellRes

− :VS.RRC.SuccConnEstab.CellRes

[Counters (Cell)

− : RRC.AttConnEstab.IRATCelRes

− : RRC.SuccConnEstab.IRATCelRes

tionRATreselecionAttemptRRCConnect

tionRATreselecionSuccessRRCConnect

tionRATreselecionAttemptRRCConnect

tionRATreselecionSuccessRRCConnect



l RRC Setup Success Rate (Inter RAT Cell change order)

[Counters (Cell)

− : VS.RRC.AttConnEstab.IRATCCO

− :VS.RRC.SuccConnEstab.IRATCCOOrderCellChangeionSuccessRRCConnect

OrderCellChangeionAttemptRRCConnect

13



l RRC Setup Success Rate (Registration)

[Counters (RNC)

− : VS.RRC.AttConnEstab.Reg

− :VS.RRC.SuccConnEstab.Reg

[Counters (Cell)

− : RRC.AttConnEstab.Reg

− : RRC.SuccConnEstab.Reg

onregistratiionAttemptRRCConnect

onregistratiionSuccessRRCConnect

onregistratiionAttemptRRCConnect

onregistratiionSuccessRRCConnect


Chapter 1 RRC Establishment Counter and KPIChapter 1 RRC Establishment Counter and KPI



Chapter4 RB Counter and KPIChapter4 RB Counter and KPI

14


l Security Mode Command Success Rate

[Formula

[Measurement scope:

− RNC

[Description

− This KPI can be used to evaluate security mode success rate in RNC

%100*_SMCAttemptSMCSuccessSRSMC =

Security Mode Counter and KPI


Security Mode Counter and KPI

l Security Mode Command Success Rate

[ Counters

−

▪ VS.IU.Att.SecMode

▪ The measurement is triggered at point A as shown in the figure, that is, when

RNC receives Security Mode Command

from CN

−

▪ VS.IU.Succ.SecMode

SMCAttempt

SMCSuccess

▪ The measurement is triggered at point B as shown in the figure, that is, when RNC sends Security Mode Complete to CN

15







RAB Establishment Counter and KPI

l CS RAB counter system in RNC

[ CS RAB establishment attempt

− Based on Qos

▪ CS Conversational; CS Streaming

− Different service rates

▪ Conv0.32; Str0.32

▪ Conv32.64; Str32.64

[ CS RAB establishment successfully:

− CS conversational Noqueuing; CS conversational queuing

− CS streaming Noqueuing; CS streaming queuing

− Different service rates

▪ Conv0.32; Str0.32

▪ Conv32.64; Str32.64

16



l CS RAB counter system in Cell

[ CS RAB establishment attempt and Success

− Based on Qos

▪ CS Conversational; CS Streaming

− Based on services

▪ AMR, CS64

− Based on service rates

▪ Conv0. 32; Conv32. 64

▪ Stre0.32; Str32.64



l PS RAB counter system in RNC

[ PS RAB establishment attempt

− Based on QoS

▪ Conversational; Streaming; Interactive; Background

− Based on different service rates and QoS

− Based on typical PS service rates

[ PS RAB establishment successfully:

− Based on QoS and Queuing



17



l PS RAB counter system in Cell

[ PS RAB establishment attempt

− Based on QoS




[ PS RAB establishment successfully:

− Based on QoS





RAB Assignment Counter

l RAB Assignment Request (CS)[ CS RAB setup request based on QoS at point A (RNC):

− RAB.AttEstabCS.Conv

− RAB.AttEstabCS.Strm

[ CS RAB setup request based on QoS at point A (Cell):

− VS.RAB.AttEstabCS.Conv

− VS.RAB.AttEstabCS.Str

[ Notes: These counters can be used to evaluate the total CS RAB setup success rate

18



l RAB Assignment Request (CS)[ CS RAB setup request for different services rates (RNC):

− VS.RAB.AttEstCSConv0.32.RNC

− VS.RAB.AttEstCSConv32.64.RNC

− VS.RAB.AttEstCSStr0.32.RNC

− VS.RAB.AttEstCSStr32.64.RNC

[ CS RAB setup request for different services (Cell):

− VS.RAB.AttEstab.AMR

− VS.RAB.AttEstCS.Conv.64

[ Notes: These counters can be used to evaluate different CS services RAB setup success rate.



l RAB Assignment Response (CS)[ CS RAB setup complete based on QoS at point B (RNC):

− RAB.SuccEstabCSNoQueuing.Conv

− RAB.SuccEstabCSNoQueuing.Strm

− RAB.SuccEstabCSQueuing.Conv

− RAB.SuccEstabCSQueuing.Strm

[ CS RAB setup complete based on QoS at point B (Cell):

− VS.RAB.SuccEstabCS.Conv

− VS.RAB.SuccEstabCS.Str

[ Notes: These counters can be used to evaluate the total CS RAB setup success rate

19



l RAB Assignment Response (CS)[ CS RAB setup complete for different services rates (RNC):

− VS.RAB.SucEstCSConv0.32.RNC

− VS.RAB.SucEstCSConv32.64.RNC

− VS.RAB.SucEstCSStr0.32.RNC

− VS.RAB.SucEstCSStr32.64.RNC

[ CS RAB setup complete for different services (Cell):

− VS.RAB.SuccEstab.AMR

− VS.RAB.SuccEstCS.Conv.64

[ Notes: These counters can be used to evaluate different CS services RAB setup success rate.



l RAB Assignment Request (PS)[ PS RAB setup request at point A (RNC):

− VS.RAB.AttEstPSInt0.32.RNC

− VS.RAB.AttEstPSBkg0.32.RNC

− VS.RAB.AttEstabPS.64.RNC



[ PS RAB setup request at point A (Cell):

− VS.RAB.Att.Est.PS.Int.0.32

− VS.RAB.Att.Est.PS.Bkg.0.32

− VS.RAB.AttEstPS.64



20



l RAB Assignment Response (PS)[ PS RAB setup complete for different services (RNC):

− VS.RAB.SucEstPSInt0.32.RNC

− VS.RAB.SucEstPSBkg0.32.RNC

− VS.RAB.SuccEstabPS.384.RNC



[ PS RAB setup complete for different services (Cell):

− VS.RAB.Suc.Est.PS.Int.0.32

− VS.RAB.Suc.Est.PS.Bkg.0.32

− VS.RAB.SuccEstPS.64




l RAB Setup Success Rate

[Formula

[Measurement scope:

− RNC & Cell

[Description

− This KPI can be used to evaluate the RAB setup success ratio fordifferent service in RNC or cell.

%100_ ×=temptRABSetupAtccessRABSetupSuSRRABS

RAB Assignment KPI

21


RAB Assignment KPI

l AMR RAB Setup Success Rate

[ Counters (RNC)

− : VS.RAB.AttEstCSConv0.32.RNC

− : VS.RAB.SuccEstCSConv0.32.RNC

[ Counters (Cell)

− : VS.RAB.AttEstab.AMR

− :VS.RAB.SuccEstab.AMR

pAttemptAMRRABSetu

pSuccessAMRRABSetu

pAttemptAMRRABSetu

pSuccessAMRRABSetu


RAB Assignment KPI

l Video Call RAB Setup Success Rate

[ Counters (RNC)

− : VS.RAB.AttEstCSConv32.64.RNC

− : VS.RAB.SuccEstCSConv32.64.RNC

[ Counters (Cell)

− : VS.RAB.AttEstCS.64

− :VS.RAB.SuccEstCS.64

AttemptVPRABSetup

SuccessVPRABSetup

AttemptVPRABSetup

SuccessVPRABSetup

22


RAB Assignment KPI

l PS64 RAB Setup Success Rate

[ Counters (RNC)

− : VS.RAB.AttEstabPS.64.RNC

− : VS.RAB.SuccEstabPS.64.RNC

[ Counters (Cell)

− : VS.RAB.AttEstPS.64

− :VS.RAB.SuccEstPS.64

temptRABSetupAtPS 64

ccessRABSetupSuPS 64

temptRABSetupAtPS64



RAB Assignment KPI


[ Counters (RNC)



[ Counters (Cell)



temptRABSetupAtPS128

ccessRABSetupSuPS128



23


RAB Assignment KPI


[ Counters (RNC)



[ Counters (Cell)








RAB Assignment KPI

l HSDPA RAB Setup Success Rate

[ Counters (Cell)

− : VS.HSDPA.RAB.AttEstab

− : VS.HSDPA.RAB.SuccEstab

tupAttemptHSDPARABSe

tupSuccessHSDPARABSe

24


RAB Failure Counter

l CS RAB Failure Counter (Cell)

[Failure statistic based on different reasons :

− VS.RAB.FailEstabCS.TNL

− VS.RAB.FailEstabCS.RNL

▪ VS.RAB.FailEstCS.Relo

▪ VS.RAB.FailEstCS.RIPFail

▪ VS.RAB.FailEstCS.Unsp

▪ VS.RAB.FailEstabCS.RNL.Other

− VS.RAB.FailEstabCS.Other.Cell


RAB Failure Counter

l CS RAB Failure Counter (Cell)


− VS.RAB.FailEstCS.Unsp

▪ VS.RAB.FailEstCs.Power.Cong

▪ VS.RAB.FailEstCs.ULCE.Cong

▪ VS.RAB.FailEstCs.DLCE.Cong

▪ VS.RAB.FailEstCs.Code.Cong

▪ VS.RAB.FailEstCs.IUB.Band

25


RAB Failure Counter

l PS RAB Failure Counter (Cell)


− VS.RAB.FlEstPS.Str.TNL

− VS.RAB.FlEstPS.Str.RNL

▪ VS.RAB.FailEstPS.RIPFail

▪ VS.RAB.FailEstPS.Par

▪ VS.RAB.FailEstPS.Relo

▪ VS.RAB.FailEstPS.Unsp

▪ VS.RAB.FlEstPS.Str.RNL.Other

− VS.RAB.FailEstabPS.Other.Cell


RAB Failure Counter

l PS RAB Failure Counter (Cell)


− VS.RAB.FailEstPS.Unsp

▪ VS.RAB.FailEstPs.Power.Cong

▪ VS.RAB.FailEstPs.Code.Cong

▪ VS.RAB.FailEstPs.ULCE.Cong

▪ VS.RAB.FailEstPs.DLCE.Cong

▪ VS.RAB.FailEstPs.IUB.Band

26







RB Counter System

l RB setup counters (Cell)[ Radio Bearer setup counters at point A:

− VS.AttRBSetup

[ Radio Bearer setup complete at point B:

− VS.SuccRBSetup

27


RB Counter System

l RB setup failure counters (Cell)[ Radio Bearer setup failure, due to:

− Configuration unsupported: VS.FailRBSetup.CfgUnsup

− Physical channel failure: VS.FailRBSetup.PhyChFail

− Cell update occurred: VS.FailRBSetup.CellUpd

− Invalid configuration: VS.FailRBSetup.IncCfg

− No reply: VS.FailRBSetup.NoReply


RB Counter System

l RB reconfigure counters (Cell)[ Radio Bearer reconfiguration at point A:

− VS.AttRBRecfg

[ Radio Bearer reconfiguration complete at point B:

− VS.SuccRBRecfg

28


RB Counter System

l RB reconfigure failure counters (Cell)[ Radio Bearer reconfiguration failure, due to:

− Configuration unsupported: VS.FailRBRecfg.CfgUnsup

− Physical channel failure: VS.FailRBRecfg.PhyChFail

− Cell update occurred: VS.FailRBRecfg.CellUpd

− Invalid configuration: VS.FailRBRecfg.IncCfg

− No reply: VS.FailRBRecfg.NoReply


Summary

l This chapter mainly explained the KPIs about Accessibility

[RRC connection success rate

[RAB setup success rate

[Radio bearer counters

SummarySummary

29

Thank youwww.huawei.com

http://www.huawei.com

9 wcdma radio network access counter and kpi

Documents

rb counter

huawei confidential

security mode counter

rab assignment counter

wcdma access counter

kpi3huawei technologies

uuterminating low priority

restoriginating low