1002 model - directeddealers.com · 1002 model owner’s guide ... and the unit is returned to...

11000022 MMooddeell➤OOwwnneerr’’ss GGuuiiddee

i© 2006 d i rected e lectronics

lliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyyDirected Electronics ("Directed") promises to the original purchaser to repair or replacewith a comparable reconditioned model any Directed unit (hereafter the "unit"), exclud-ing without limitation the siren, the remote transmitters, the associated sensors and acces-sories, which proves to be defective in workmanship or material under reasonable use dur-ing the lifetime of the vehicle provided the following conditions are met: the unit was pro-fessionally installed and serviced by an authorized Directed dealer; the unit will be pro-fessionally reinstalled in the vehicle in which it was originally installed by an authorizedDirected dealer; and the unit is returned to Directed, shipping prepaid with a legible copyof the bill of sale or other dated proof of purchase bearing the following information: con-sumer's name, telephone number and address; the authorized dealers name, telephonenumber and address; complete product description, including accessories; the year, makeand model of the vehicle; vehicle license number and vehicle identification number. Allcomponents other than the unit, including without limitation the siren, the remote trans-mitters and the associated sensors and accessories, carry a one-year warranty from the dateof purchase of the same. This warranty is non-transferable and is automatically void if: theoriginal purchaser has not completed the warranty card and mailed it within ten (10) daysof the date of purchase to the address listed on the card; the unit's date code or serial num-ber is defaced, missing or altered; the unit has been modified or used in a manner con-trary to its intended purpose; the unit has been damaged by accident, unreasonable use,neglect, improper service, installation or other causes not arising out of defects in materi-als or construction. The warranty does not cover damage to the unit caused by installa-tion or removal of the unit. Directed, in its sole discretion, will determine what consti-tutes excessive damage and may refuse the return of any unit with excessive damage. TOTHE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUD-ING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSEAND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY,ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NORAUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY,OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANYAND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEAL-ERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THISUNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOTOFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAM-AGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; ANDHEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUD-ING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/ORVANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FORMAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY

ii © 2006 d i rected e lectronics

CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIMOR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPERVENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLYAND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANYCLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THEAUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEV-ER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OFEARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITYAND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURERDOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON-TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations onhow long an implied warranty will last or the exclusion or limitation of incidental or con-sequential damages. This warranty gives you specific legal rights and you may also haveother rights that vary from State to State.

This product may be covered by a Guaranteed Protection Plan ("GPP"). See your autho-rized Directed dealer for details of the plan or call Directed Customer Service at 1-800-876-0800. Directed security systems, including this unit, are deterrents against possibletheft. Directed is not offering a guarantee or insurance against vandalism, damage or theftof the automobile, its parts or contents; and hereby expressly disclaims any liability what-soever, including without limitation, liability for theft, damage and/or vandalism.Directed does not and has not authorized any person or entity to create for it any otherobligation, promise, duty or obligation in connection with this security system.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

➤ Date of purchase➤ Your full name and address➤ Authorized dealer's company name and address➤ Type of alarm installed➤ Year, make, model and color of the automobile➤ Automobile license number➤ Vehicle identification number➤ All security options installed on automobile➤ Installation receipts

iii© 2006 d i rected e lectronics

ttaabbllee ooff ccoonntteennttsslliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyy.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. iissttaannddaarrdd rreemmoottee ccoonnttrrooll ccoonnffiigguurraattiioonn .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 11wwhhaatt iiss iinncclluuddeedd.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 33iimmppoorrttaanntt iinnffoorrmmaattiioonn .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 33

system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

rreeppllaacceemmeenntt rreemmoottee ccoonnttrroollss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 55rreemmoottee ccoonnttrrooll ffuunnccttiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 55

standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6uussiinngg yyoouurr ssyysstteemm .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 88

active arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8passive arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8multi-level security arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12high security disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12disarming without a remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13dome light control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14silent mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15valet mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15one-time bypass. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16nuisance prevention® circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

aauuxxiilliiaarryy oouuttppuuttss ((ooppttiioonnss)) .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1188ddiiaaggnnoossttiiccss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1199

arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19disarming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20system status chirps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21interpreting zone diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

ccooddee hhooppppiinngg .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2222hhiigghh ffrreeqquueennccyy .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2233oowwnneerr rreeccooggnniittiioonn .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2233rraappiidd rreessuummee llooggiicc .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2244ppoowweerr ssaavveerr mmooddee .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2244pprrooggrraammmmiinngg .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2255

iv © 2006 d i rected e lectronics

iinnssttaallllaattiioonn ooppttiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2288vveehhiiccllee rreeccoovveerryy ssyysstteemm ((vvrrss®®)) .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2299

arming the vrs® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30vrs® triggered sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30disarming the vrs® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

pprrooggrraammmmiinngg ooppttiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3322sshhoocckk sseennssoorr aaddjjuussttmmeenntt .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3344

enter shock sensor adjustment mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34adjusting the shock sensor setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34exit shock sensor adjustment mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35reset shock sensor to default setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

sseeccuurriittyy && ccoonnvveenniieennccee eexxppaannssiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3377gglloossssaarryy ooff tteerrmmss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 3399qquuiicckk rreeffeerreennccee gguuiiddee .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 4411

1© 2006 d i rected e lectronics

ssttaannddaarrdd rreemmoottee ccoonnttrrooll ccoonnffiigguurraa--ttiioonn

controls the LLoocckk––AArrmm//PPaanniicc OOnn//PPaanniicc OOffff function.

controls the UUnnlloocckk––DDiissaarrmm//PPaanniicc OOffff function.

controls SSiilleenntt MMooddee™™ and an AAuuxxiilliiaarryy OOuuttppuutt ((22)).

controls the PPaanniicc OOnn//OOffff function.

and pressed together control an AAuuxxiilliiaarryy OOuuttppuutt ((33)).





wwhhaatt iiss iinncclluuddeedd➤ One control module

➤ A pair of four-button remote controls

➤ Wire harnesses

➤ The 514N six-tone programmable siren

➤ The status LED indicator light

➤ A push-button Valet switch

➤ Your warranty registration

➤ Failsafe® Starter Kill ready circuitry

(may require additional labor)

➤ External receiver/antenna

iimmppoorrttaanntt iinnffoorrmmaattiioonnCongratulations on the purchase of your state-of-the-art vehicle

security system. This system has been designed to provide years

of trouble-free operation. Due to the complexity of this system,

it must be installed by an authorized dealer only. Installation of

this product by anyone other than an authorized dealer voids the

warranty. All dealers are provided with preprinted dealer certifi-

cates to verify that they are authorized.

This owner’s guide should help you to get the most out of your

system. Please take the time to read it prior to using the system.


system maintenanceThe system requires no specific maintenance. Your remote

control is powered by a small, lightweight 3 volt lithium battery

(CR2032) that will last approximately one year under normal

use. When the battery weakens, operating range will be reduced.

your warrantyYour warranty registration must be returned and the bar code

serial number must not be removed. If the warranty registration

is not returned, you do not have a warranty. It is also necessary

to keep your proof of purchase, which reflects that the product

was installed by an authorized dealer. Make sure that you receive

the warranty registration from your dealer.

fcc/id noticeThis device complies with Part 15 of FCC rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesirable operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate this device.

➜

➜

➜


rreeppllaacceemmeenntt rreemmoottee ccoonnttrroollssYou can purchase replacement remote controls from your

Authorized Dealer or on-line at the following web site:

www.directedstore.com

Once you receive your new remote control, please refer to

instructions included on the remote packaging.

rreemmoottee ccoonnttrrooll ffuunnccttiioonnssThis system uses a computer-based learn routine to learn the

Remote Control buttons. This makes it possible to assign any

remote control button to any system function. The remote

control initially comes programmed with Standard

Configuration, but may also be customized by an authorized

dealer. The buttons described in this manual correspond to a

Standard Configuration remote control.


standard configurationButton

The arming function is controlled by pressing this button for

one second.

Button

The disarming function is controlled by pressing this button for

one second.

Button

Silent Mode™ and an optional auxiliary function are controlled

by pressing this button. (Silent Mode works by pressing this

button for less than one second before arming or disarming. An

optional auxiliary function, such as trunk release, can be

controlled by pressing this button for 1.5 seconds.)

The auxiliary output controls __________________________.

Button

The panic feature is controlled by pressing this button for two

seconds.

and Buttons

An optional auxiliary convenience or expansion function that

you have added to your system can be activated by pressing these

buttons simultaneously.

The auxiliary output controls_________________________.

and Buttons


➜





and Buttons





and Buttons






uussiinngg yyoouurr ssyysstteemmThe buttons described in this manual correspond to the standard

configuration. Remember, this is not the only way your Remote

Control may be set up. It can be custom configured to meet your

needs.

active armingYou can activate, or arm, the system by pressing on your

remote control for one second. When the system arms, you will

hear a short siren sound, or chirp, and the parking lights will

flash once. If the vehicle’s power door locks have been connected

to the system, the doors will lock.

While the system is armed, the status LED will flash approxi-

mately once per second, indicating that the system is actively

protecting your vehicle. If you hear a second chirp after arming,

and see the status LED flashing in groups, refer to the Diagnostics

section of this guide. This extra chirp is called Bypass Notification.

passive armingThe system also can be programmed to arm itself automatically

(called passive arming). If the system is programmed for passive

arming, it will automatically arm 30 seconds after the ignition is

turned off and the system "sees" you leave the vehicle by opening

and closing a door. Whenever the system is in its 30-second

passive-arming countdown, the status LED will flash twice as

➜

➜


fast as it does when the system is armed. The siren will chirp

once 20 seconds after the last door has been closed. The system

is not actually armed at that point. The system arms and the

doors lock (if connected and programmed for passive locking) at

the 30 second mark, but the siren will not chirp. The early chirp

provides you with a 10-second warning prior to arming.

note: If any protected entry point (such as a door or aswitch-protected trunk or hood) is open, the system willnot passively arm (unless forced passive arming is pro-grammed on). See Programming Options section of thisguide. Additionally, each time a protected entry is trig-gered during the arming countdown, the 30-secondcountdown starts over.


When armed, your vehicle is protected as follows:

➤ Light impacts will trigger the Warn Away® signal. When

triggered, the siren will chirp and the parking lights will flash

for a few seconds.

➤ Heavy impacts will trigger the system. The triggered

sequence is between 1-180 seconds of constant siren and

flashing parking lights.

➤ If a door is opened, the system will immediately start

chirping the siren and flashing the parking lights. Three

seconds later, the siren output changes to a continuous blast.

This progressive response gives you time to disarm the sys-

tem with your remote control if you inadvertently open the

door while the system is armed, while still providing an

instant response (even if the door is immediately closed).

➤ Turning on the ignition key will trip the same two-stage

response as opening a door.

➤ The optional starter kill prevents the vehicle’s starter from

cranking.

multi-level security armingMulti-Level Security Arming allows you to select which of the

security system's inputs or sensors will be active and which will

be bypassed at the time that the system is armed. (See the Table

of Zones section of this guide.) Pressing again within five

seconds of arming the security system will activate the Multi-

Level Security Arming feature. Each time is pressed again, a

different security level is selected. The different security levels

can be selected as follows:

➜


➤ Press one time: The parking lights flash once. The

system is armed.

➤ Press a second time within five seconds: The parking

lights flash twice. Zone 2 is now bypassed.

➤ Press a third time within five seconds: The parking

lights flash three times. Zone 4 is now bypassed.

➤ Press a fourth time within five seconds: The parking

lights flash four times. Zone 7 is now bypassed.

➤ Press a fifth time within five seconds: The parking

lights flash five times. Zones 2 and 4 are now bypassed.

➤ Press a sixth time within five seconds: The parking

lights flash six times. Zones 2 and 7 are now bypassed.

➤ Press a seventh time within five seconds: The parking

lights flash seven times. Zones 4 and 7 are now bypassed.

➤ Press an eigth time within five seconds: The parking

lights flash eight times. All input zones, except zone 5, are

now bypassed.

➤ Continued pressing of will begin the Multi-Level

Security Arming cycle over again.

note: Multi-Level Security Arming only applies to a sin-gle arming cycle. Once the system is disarmed and thenre-armed, all the zones will be active again.


disarmingTo disarm the system, press . You will hear two chirps, and

the parking lights will flash twice. If the power locks are

connected to the system, the doors will unlock. If the siren chirps

either four or five times when disarming, refer to the Diagnostics

section of this guide. This is called Tamper Alert.

high security disarmThis security system offers High Security Disarm. High Security

Disarm is a feature that makes it possible to silence and reset the

system while it is triggering, without disarming the system. If the

system is triggered and the siren has been sounding for longer

than six seconds, pressing or on the remote remote

control will stop the trigger and return the unit to the armed

state. The system will not disarm, but rather reset. This prevents

you from disabling the system should you wish to disarm it

without visually checking the vehicle. Pressing after reset-

ting the system will disarm the system; pressing this button

during the first six seconds of the triggered sequence will disarm

the security system immediately. The six second timer is

provided for your convenience, in case the system is accidentally

triggered.

➜

➜


disarming without a remote controlThis feature allows you to disarm the security system without the

Remote Control should it be lost, damaged, or disabled. In order to

disarm the system without a remote remote control, you must have

the vehicle’s ignition key and know where the Valet button is

located. Be sure to check with the installer for the location and the

number of presses of the Valet button required to disarm the system.

To disarm the security system,

turn the ignition to the ON posi-

tion. Press the Valet button the

preset number of times (one to

five times) within 15 seconds. After five seconds the system will

disarm. If the system does not disarm, you may have waited too long;

turn the ignition off and on and try again.

Location of Valet Button_________________________________

Number of Pulses______________________________________

important! The unit can be programmed to respond toone to five pulses of the Valet button for the disarm func-tion. Be sure to check with the installer for the desiredprogramming.

DRW-35

➜


dome light controlsecurity only

The dome light activates for 30-seconds after the system is

disarmed.

Ignition controlled

The dome light activates for 30-seconds after the ignition is

turned Off.

door controlled

The dome light activates for 30-seconds after the system sees a

door has closed. (If door was held open for longer than 3

minutes the dome light will not illuminate.)

full

The dome light activates for 30-seconds after seeing door

closure, ignition, or security disarm. (This is the factory setting.)

silent modeTo temporarily turn off the arm or disarm chirps, use Silent

Mode™. Simply press for less than one second before

arming or disarming, and the confirmation chirp(s) will be elim-

inated for that one operation only. If you want the arm/disarm

chirps turned off permanently, your dealer can do this for you.

note: The Warn Away® response to lighter impacts isbypassed if the system is armed using Silent Mode. Thisensures that no chirps will be emitted by the siren in anarea you want chirp-free. The system is still fully capableof triggering. Only the Warn Away® response is bypassed.

➜

➜


panic modeIf you are threatened in or near your vehicle, you can attract

attention by triggering the system with your remote control. Just

press or for two seconds, and you will enter Panic

Mode. The siren will sound and the parking lights will flash for

the programmed siren duration. To stop Panic Mode at any time,

press , or on the remote control again.

valet modeYou can prevent your security system from automatically arming

and triggering by using Valet Mode. This is very useful when

washing the vehicle or having it serviced. In Valet Mode, the

security system will not arm, even with the Remote Control, but

all convenience functions (door locks, trunk release, etc.) will

continue to work normally.

To enter or exit Valet Mode:

1. Turn the ignition on.

2. Turn the ignition off.

3. Press and release the Valet

button within 10 seconds.

The status LED will light solidly if you are entering Valet Mode,

and it will go out if you are exiting Valet Mode.

DRW-35

➜

➜


To enter or exit Valet Mode using the remote control:

1. Open any vehicle door.

2. Press .

3. Press or .

4. Press again.

The status LED will light solidly if you are entering Valet Mode,

and it will go out if you are exiting Valet Mode.

one-time bypassThis feature (if programmed On) stops the alarm from arming oractivating any outputs that are programmed to activate when thealarm is armed.

One-time bypass will defeat the following actions:

Passive arming: If programmed ON the alarm will not armitself.

If the remote is used to arm the alarm after exiting the vehicle:

Window roll up: If programmed ON this output will notactivate.Linked Auxiliary Outputs: If programmed to activate onarm, they will not activate.

To activate one-time bypass:

1. After parking turn the ignition off.

2. Turn the ignition On for more than 1-second and less than

3-seconds and then turn Off.

3. The siren will chirp once to indicate one-time bypass has

been activated.

➜


To cancel one-time bypass perform one of the following:

Arm then disarm the alarm.

Turn the ignition On for more than 3-seconds.

nuisance prevention® circuitryYour system has Directed’s Nuisance Prevention® Circuitry(NPC®). It prevents annoying repetitive trigger sequences due tofaulty door pin switches or environmental conditions such asthunder, jackhammers, airport noise, etc.

Example

If the alarm triggers three times within a 60-minute period andeach time the same sensor or switch triggers the alarm, NPC® willinterpret those triggers as false alarms. After the third trigger,NPC® ignores, or bypasses, that sensor or switch (along with anyother sensors or switches sharing the same zone) for 60 minutes.

If the bypassed sensor tries to trigger the system while it is beingbypassed, the 60-minute bypass period will start over. This ensuresthat a sensor that continually triggers will remain bypassed.

Doors are covered by NPC® differently; if the alarm is triggeredby an open door for three full cycles, the doors will be bypasseduntil the trigger ceases.

note: Arming and disarming the system does not reset thisfunction. In order to reset a bypassed zone, the same zonemust not trigger for 60 minutes, or ignition is turned On.If testing your system, it is important to remember that theNPC® programming can cause zones to be bypassed andappear to stop working. If five chirps are heard when dis-arming, NPC® has been engaged. If you wish to clear theNPC® memory, turn the ignition key on.

➜


NPC® is programmable. See Programming Options section of this

guide.

aauuxxiilliiaarryy oouuttppuuttss ((ooppttiioonnss))This system also supplies outputs that can control convenience

options such as remote control trunk release and window automa-

tion. Consult your dealer for available options for your system.

Channel 2 Trunk release: When connected, pressing for 1.5

seconds will remotely release the vehicle trunk lid.

Channel 3 auxiliary output: When connected, pressing and

will immediately activate this output to control an

additional convenience option.











ddiiaaggnnoossttiiccssThe microprocessor at the heart of your security system is

constantly monitoring all of the switches and sensors that are

connected to it. It detects any faulty switches and sensors and

prevents them from disabling the entire system. The micropro-

cessor will also record and report any triggers that occurred

during your absence. Refer to the System Status Chirps and Table

of Zones charts for diagnostic information.

arming diagnosticsIf the system is armed while an input is active (door open, sensor

triggering, etc.) the unit will chirp once when arming and then

one more time a few seconds later. This is called Bypass

Notification.

The security system will ignore the input that was active when

the system was armed, until the input goes away. Three seconds

later the system will monitor that input normally. For example,

if your vehicle has interior light exit delay, and you arm the

system before the interior light goes out, you may hear Bypass

Notification chirps. Once the light shuts off, however, the doors

are monitored normally.

note: Bypass Notification will not occur when usingSilent Mode™ or if chirps have been programmed OFF.

➜


disarming diagnosticsExtra disarm chirps are the Tamper Alert. If four chirps are heard

when disarming, the system was triggered in your absence. If five

chirps are heard, a zone was triggered so many times that Nuisance

Prevention® Circuitry has bypassed that zone (see NPC section of

this guide). The status LED will indicate which zone was involved.

(See Table of Zones section of this guide.) The system will retain this

information in its memory, and continue to chirp four or five times

each time it is disarmed, until the next time the ignition key is

turned on.

system status chirpsThe siren will chirp when arming/disarming the system. The

pattern of chirps will audibly report the system’s status as

described below.

Action Number of Chirps Description

Arm 1 System armed

Arm 1 (3-second delay), 1 System armed with Bypass Notification

Disarm 2 System disarmed

Disarm 4 System disarmed with Tamper Alert

Disarm 5 System disarmed NPC®

active

➜

➜


table of zonesThe zone number is the number of LED flashes used by the

system to identify that input. The standard input assignments

are listed below, along with spaces to write in any optional

sensors or switches you have had installed.

interpreting zone diagnosticsWarn Away responses are not reported by arming or disarming

diagnostics. If you receive a Bypass notification when arming or

a Tamper Alert notification when disarming, look at the LED.

Active or triggered zones will be indicated by a pattern of blinks

by the LED.

➜

Zone - Number Dealer-Installedof LED Flashes Description Options

1 Instant trigger - often usedfor trunk pinswitches

2 Shock sensor input - a light impact activates warnaway and a heavier impact activates full alarm.

3 Door switch trigger

4 Optional sensor inputs for warn away and full alarm notification.

5 Ignition trigger

6 Hood trigger

7 Optional sensor inputs for warn away and full alarm notification.

➜


Example

If Zone 3 was active or triggered, the LED will blink three times

with a two-second pause. Then it will blink three times again,

and repeat until the ignition is turned on.

ccooddee hhooppppiinnggThe receiver and remote controls each use mathematical

formulas called algorithms to change their codes each time the

remote control is used. This technology has been developed to

increase the security of the unit. The control unit knows what the

next codes should be. This helps to keep the remote control "in

sync" with the control unit even if you use the remote control out

of range of the vehicle. However, if the remote control has been

pressed many times out of range of the vehicle, or if the battery

has been removed, it may get out of sync with the control unit

and fail to operate the system. To re-sync the remote control

simply press of the remote control several times within range

of the vehicle. The alarm will automatically re-sync and respond

to the Remote Controls normally.

note: Your system stores the last six triggered zones inmemory. If your system has been triggered but the LEDhas been reset by turning on the ignition, your dealer canstill recall the last six zones that were triggered. Contactyour dealer for details.


hhiigghh ffrreeqquueennccyyYour system transmits and receives at 434 MHz. This provides a

cleaner spectrum with less interference and a more stable signal.

Enjoy a phenomenal increase in range – even in areas with high

radio interference.

oowwnneerr rreeccooggnniittiioonnOwner Recognition is a feature available exclusively from Directed.

Using the Directed Bitwriter®, a hand-held programming tool,

your dealer can program many of the system settings. The

programmer makes it possible to program different settings for

each Remote Control that is used with the system. Then, whenev-

er a specific remote control is used, the system will recall the

settings assigned to that remote control. Owner Recognition lets up

to four users of the system have different settings that meet their

specific needs. It is almost like having four separate alarms in your

vehicle, one for each user.

note: Owner Recognition cannot be programmed with-out a Directed Bitwriter® and the necessary software.Check with your dealer for more information.


rraappiidd rreessuummee llooggiiccThis Directed system will store its current state to non-volatile

memory. If power is lost and then reconnected, the system will

recall the stored state from memory. This means if the unit is in

Valet Mode and the battery is disconnected for any reason, such

as servicing the car, when the battery is reconnected the unit will

still be in Valet Mode. This applies to all states of the system

including arm, disarm, VRS®, and Valet Mode.

ppoowweerr ssaavveerr mmooddeeYour system will automatically enter Power Saver Mode while

armed or in Valet Mode, after a period of time in which no oper-

ation has been performed. This lowers the current draw to the

vehicle’s battery. Power Saver Mode takes over under the

following conditions:

➤ Power Saver when the system is armed: After the system has

been armed for 24 hours, the LED will flash at half its

normal rate, decreasing the system's current draw.

➤ Power Saver in Valet Mode: When the system enters Valet

Mode the LED illuminates steadily. If the vehicle is not used

(ignition is not turned on) for a period of one hour while the

system is in Valet Mode, the LED will shut off. If the system

remains in Valet Mode, the LED will come back on the next

time the ignition is turned on and then back off.


pprrooggrraammmmiinnggProgramming options control what your system does during

normal operation, and require few or no additional parts.

However, some may require additional installation labor.

The following is a list of the program settings, with the factory

settings in BBoolldd::

➤ AAccttiivvee aarrmmiinngg (only with the remote control) or passive arming

(automatic arming 30-seconds after the last door has been

closed).

➤ Arming/disarming confirmation siren chirps oonn or off.

➤ The ignition controlled door lock feature oonn or off: With

this feature on, the doors will lock three seconds after the

ignition is turned on, and the doors are closed, and unlock

when the ignition is turned off. The system will not lock the

doors when the ignition is turned on with any door open.

Ignition lock and unlock are independent features and can

be programmed separately. You can also do these indepen-

dently when programming manually.

➤ Passive door locking (with passive arming) or aaccttiivvee ddoooorr

lloocckkiinngg (only when arming with the remote control). Passive

locking allows the vehicle's doors to lock when the security

system passively arms (after the 30 second countdown). This

feature only works if passive arming has been programmed.


➤ Panic mode eennaabblleedd/disabled with the ignition on: Some

states have laws against siren capability in a moving vehicle.

➤ Forced passive arming oonn or off: If your system is

programmed for passive arming and the forced passive

arming feature has been programmed on, the system will

passively arm after one hour, even if a protected entry has

been left open. This feature is useful if a door has been left

ajar when leaving the vehicle. Forced passive arming ensures

that the security system will be armed in every situation.

➤ Automatic Engine Disable (AED) on or ooffff: The purpose of

this feature is to protect the vehicle from being stolen at all

times, regardless of whether or not the alarm is armed. If

AED is programmed on, the starter of the vehicle will be dis-

abled 30 seconds after the ignition is turned off. Once the

key is turned off, the LED will flash slowly (one-half its

normal armed rate) to indicate the AED arming cycle.

Thirty seconds later, the starter of the vehicle will be dis-

abled. To start the car, it will be necessary to disarm the

system with the remote control. It is also possible to disarm

note: When the system passively arms after one hour, theentry point that has been left open, and anything con-nected to the same zone, is bypassed and cannot triggerthe system. However, the remaining inputs to the systemare fully operational.

note: When programmed for passive arming and activelock, if the system is disarmed without a door beingopened, the system will relock the doors when it passive-ly rearms.


the AED feature by turning the ignition key to the RUN

position and pressing the Valet button the programmed

number of times. AED is disabled when the system is in

Valet Mode.

➤ Full trigger response 3300 or 60 seconds: This determines how

long the full triggered sequence lasts. Some states have laws

regulating how long a security system can sound before it is

considered a nuisance. If your installer is programming the

security system with the Directed Bitwriter®, the full trig-

gered response can be programmed for any duration ranging

from 1 to 180 seconds.

➤ Nuisance Prevention® Circuitry oonn or off: Please refer to the

NPC® section of this manual for a complete explanation of

how NPC® operates. If NPC® is programmed off, the securi-

ty system will respond to inputs from any sensor indefinitely.

➤ Progressive door trigger oonn or off: When the system is armed

and a door is opened, the system responds with ten chirps

prior to beginning the full triggered sequence. If an instant

trigger is desired, the progressive door trigger can be pro-

grammed off.

note: Because many states have laws regulating securitysystems, programming NPC® off may cause your systemto violate state laws.

note: This feature will only function if the Failsafe®

Starter Kill relay has been installed.


➤ Valet pulse count: The number of presses of the Valet button

required to disarm the security system, AED, or the VRS®

system can be programmed from one to five presses. The

default setting is oonnee press.

➤ Siren tones and chirp volume: The output of the Revenger®

Soft Chirp® siren consists of six different tones in sequence.

Any of these tones can be eliminated by your dealer, result-

ing in a unique, easily identifiable siren sound. The siren

chirps can be either full volume or ssiixx ddeecciibbeellss qquuiieetteerr than

the full alarm blast.

iinnssttaallllaattiioonn ooppttiioonnssThe system has many options that may require extra parts and

labor. Some of the possibilities are listed here.

➤ Progressive unlocking: In most cars with electric power door

locks, the system can be configured so that when the system is

disarmed, only the driver’s door unlocks. A second press of the

button unlocks the other doors.

➤ Vehicle Recovery System (VRS®): VRS® is an anti-carjacking

device designed to help in the safe recovery of your vehicle

in case of a carjacking. Please refer to the Vehicle Recovery

System section of this guide for a complete explanation of

how the Vehicle Recovery System operates.


vveehhiiccllee rreeccoovveerryy ssyysstteemm ((vvrrss®®))The optional VRS® feature is designed to ensure that any unautho-

rized user of your vehicle (even if using your keys and remote control)

will not be able to permanently separate you from your vehicle.

The VRS® cannot prevent a carjacking attempt; however, it does

ensure that if your vehicle is taken by an unauthorized user, it will

be disabled (after several progressive warnings) as safely as

possible. Should a carjacking occur, the VRS® allows you to

concern yourself with your personal safety without worrying

about your property.

Directed has engineered this vehicle security system, the Failsafe®

Starter Kill, and the VRS® feature to provide the best combina-

tion of personal safety and property protection available. When

properly installed, the system can never inadvertently stop your

vehicle in traffic or on railroad tracks while the vehicle is in oper-

ation. It is unlike other systems that shut down your engine

while it is running. This system is designed to perform starter in-

terrupt, or starter kill. The Failsafe® Starter Kill cannot shut

down an already-running engine – it can only prevent an engine

from starting in the first place.

important! Any installation that allows this product toshut down a vehicle's engine when it is running is con-trary to the product’s design and intended usage, andDirected hereby expressly disclaims any liability resultingtherefrom.


arming the vrs®

To arm the VRS®, turn the ignition to the ON position and press

the arm button on the remote control for one second. The

parking lights will flash and the siren will chirp once. This can be

done before driving or while driving the vehicle. Once the system

is armed, it will initiate its triggered sequence (see below) if any

door is opened and closed. If you are forced from the vehicle, the

system will trigger as the door is opened and closed. This is how

the system works to combat intersection carjacking. To protect

against parking lot carjacking, arm the VRS® before leaving the

vehicle. The system will now trigger automatically the next time

you or anyone drives the vehicle. This helps to protect the vehicle

if someone takes your keys and remote control by force in a

parking lot.

vrs® triggered sequenceFifteen seconds after the last door has closed, the system’s status

LED will begin flashing. This delay is intended to allow you time to

distance yourself from your vehicle in the event of a carjacking.

Forty-five seconds later, the siren begins chirping and the park-

ing lights begin flashing. This time could be used to notify au-

thorities that your vehicle has been hijacked, and tell them what

the VRS® will do next.

➜

note: If the VRS® system is armed while operating the vehi-cle and not disarmed prior to leaving the vehicle, it is stillarmed and will trigger the next time the vehicle is driven.

➜


Fifteen seconds after the siren chirps begin, the siren’s output will

change to a continuous blast.

From this point on, when the ignition key is turned off, the VRS®

will immediately turn on the starter kill. This will prevent the

vehicle from being restarted, thus immobilizing it at that spot.

Three minutes after the constant siren output begins, the flashing

parking lights and the siren will stop. The starter kill will remain

active until the system is disarmed. If the door is opened or the

ignition is turned off and on in an attempt to restart the car, the

siren and light flashing will begin again.

disarming the vrs®

Take the time to familiarize yourself with the VRS® triggering se-

quence and the disarm procedure. It is important to recognize

and identify the VRS® trigger sequence and know how to disarm

it in case of accidental activation.

Once the VRS® is armed, it does not disarm automatically. You

must disarm it the next time you operate the vehicle. You must

disarm it with one of the following procedures:

If the system has not entered the triggered sequence (siren has

not started chirping):


2. Press on the remote control for one second.

The lights will flash and the siren will chirp

➜


twice.

If the system has entered the triggered sequence (siren has begun

chirping), pressing the disarm button of the Remote Control will

not disarm VRS®. To disarm the VRS® during a VRS® trigger

sequence:


2. Press the Valet button the pre-

programmed number of times to

disarm the VRS® system.

pprrooggrraammmmiinngg ooppttiioonnssSee your dealer for further details on the options listed below

available with this system.

Automatic Engine Disable: Prevents the vehicle from being started

even if the vehicle is not armed after turning the ignition Off and

exiting the vehicle.

Comfort Closure: Windows will close upon locking the vehicle.

Dual Sensor Trigger: If programmed both the onboard and at

least one of the optional sensors need to be triggered within 1-

note: If the VRS® system has begun its chirping sequence,the ignition must be turned off, then on to disarm. If youare driving the vehicle at the time, pull to a safe placeaway from traffic and follow the triggered sequence dis-arm procedure.

DRW-35


second of each other for full alarm.

Forced Passive Arming: If passive arming is on and a door is left

open the system will be armed after 1 hour.

High Security Disarm: If the system is triggered this feature allows

the user to silence the siren and reset the system to the armed

state without having to visually check the system status.

Multi-level Arming: Allows bypassing of user selected alarm zones

of the vehicle.

Grouped Arming: Allows bypassing of the group of alarm zones

for warn-away, or both warn-away and full alarm of the vehicle.

Panic with Ignition Off: Prevents the Orange Panic button on the

remotes from activating panic with ignition On (not allowed in some

states).

Parking Light Supervision: The parking lights will illuminate for

30-seconds after disarming the system or turning the ignition off.

Remote Start Reporting: This channel 3 program option allows

bypass of the security inputs that would trigger an alarm when

activating an added optional remote start system, but still retains

a high level of security.

Retained Accessory Power: This output from the security system

can be connected to vehicle accessories. After the ignition has

been turned off, it will continue to supply power until the a door

have been open and closed.


sshhoocckk sseennssoorr aaddjjuussttmmeenntt

enter shock sensor adjustment mode

1. Press and hold and buttons for 4-seconds.

2. The system will emit 1 long chirp to indicate entry into

shock adjustment mode.

3. The LED will illuminate continuously for the duration of

shock adjustment mode.

adjusting the shock sensor setting1. Increase Sensitivity—Press and release the button to

increase shock sensor sensitivity by one step. The siren will

chirp 2-times for each step increased in adjustment. When

the shock sensor adjustment reaches maximum sensitivity

the siren will emit 2 short chirps and then 1 long chirp.

nnoottee:: When the arm and disarm are programmed to a sin-gle button, then the AUX button is used to increase thesensitivity setting of the sensor.

➜

note:: When the shock sensor adjustment mode is entered,all other timers and operations are bypassed until adjust-ment mode is exited.

important:: Prior to performing this procedure the systemmust be disarmed, the doors, trunk and hood must beclosed, and the ignition must be Off.

➜


2. Decrease Sensitivity—Press and release the button to

decrease shock sensor sensitivity by one step. The siren will

chirp 1-time for each step decreased in adjustment. When

the shock sensor adjustment reaches minimum sensitivity

(sensor is Off ) the siren will emit 1 short and then 1 long

chirp.

3. Testing Sensor—Use the heel of the palm of your hand to

strike the door pillar of the car after making an adjustment.

The siren will chirp once if the impact was great enough to

generate a full trigger. Pre-warn level is set automatically.

When desired setting is reached, sensor adjustment mode

can be exited.

exit shock sensor adjustment modeThe adjustment mode will be exited if:

➤ No input from remote control for 15-seconds.

➤ No input from sensitivity testing for 15-seconds.

➤ The ignition is turned On.

➤ The Valet button is pressed.

The siren will emit 1 long chirp and the LED will extinguish

which shock adjustment mode is exited.

➜


reset shock sensor to default settingThe shock sensor can be restored to a default setting of 10 to

facilitate re-adjustment at any time while in adjustment mode.

1. Simultaneously press the and buttons.

2. The system will emit 3 chirps to indicate the sensor has been

reset to level 10.

3. The system returns to shock sensor adjustment mode for

further adjustment, if required.

➜


sseeccuurriittyy && ccoonnvveenniieennccee eexxppaannssiioonnssHere we have listed only some of the many expansion options

available. Please contact your dealer for a complete explanation

of all the options available to you.

Audio Sensor: Metal on glass, glass cracking, and breaking glass

each produce distinctive acoustic signatures. The 506T audio

sensor uses a microphone to pick up sounds, and then analyzes

them with proprietary acoustic software to determine if the glass

has been struck.

Backup Battery: The 520T keeps the system armed, triggers the

alarm and keeps the starter kill active if main battery power is

disconnected.

Field Disturbance Sensor: An invisible dome of coverage is estab-

lished by installing the 508D "radar" sensor. Your security

system can then react to any intrusions into this field with the

triggered sequence.

Headlight and Parking Light Automation: The 545T Nite-Lite®

will automatically turn on your parking and headlights when it

gets dark. In addition, the 545T will turn your headlights on

whenever the windshield wipers are used. A remote control func-

tion can also be used to turn on your parking and headlights for

a programmed time.


Power Trunk Release: The channel two output of the system can

operate a factory power release for the vehicle’s trunk or hatch.

(An additional relay may be required.) If the factory release is not

power activated, then Directed's 522T trunk release solenoid can

often be added.

Power Window Control: Automatic power window control is pro-

vided with the 529T and 530T systems.

Valet Start System: For the ultimate in convenience, the Valet

start system can start your vehicle, monitor engine functions,

and power your climate control system with a push of a button.

Over-rev protection, open-hood lockout, brake pedal shutoff,

and automatic timer shutoff are all included. (This feature is

only for automatic transmission, fuel-injected vehicles.)


gglloossssaarryy ooff tteerrmmssControl Unit: The "brain" of your system. Usually hidden under

the dash area of the vehicle. It houses the microprocessor which

monitors your vehicle and controls all of the system's functions.

Fail Safe Starter Kill: An automatic switch controlled by the secu-

rity system which prevents the vehicle’s starter from cranking

whenever the system is armed. The vehicle is never prevented

from cranking when the system is disarmed, in Valet mode, or

should the starter interrupt switch itself fail. Your system is ready

for this feature, however installation may require additional labor.

Input: A physical connection to the system. An input can be

provided by a sensor, pinswitch or through an existing system in

the vehicle, such as ignition or courtesy lights.

LED: A light mounted somewhere in the vehicle. It is used to

indicate the status of your system. It is also used to report trig-

gers and faults in the system or sensors.

Shock Sensor: This is a sensor mounted in the vehicle that is

designed to pick up impacts to the vehicle or glass.

Siren: Noise generating device usually installed in the engine

compartment of the vehicle. It is responsible for generating the

"chirps" you hear, as well as the six tones you hear while the

alarm is triggered.

Remote control: Hand-held, remote control which operates the

various functions of your system.


Trigger or Triggered Sequence: This is what happens when the

alarm "goes off" or "trips". The triggered response of your

system consists of the siren sounding and parking light flashing

for the programmed duration.

Valet Button: A small push-button switch mounted somewhere

inside the vehicle. It is used to override the alarm when a trans-

mitter is lost or damaged, or to enter or exit Valet mode.

Warn Away Response: Lighter impacts to the vehicle will generate

the Warning Zone response. It consists of several seconds of siren

chirps and parking light flashes.

Zone: A zone is a separate input that the alarm can recognize as

unique. Each input to the system is connected to a particular

zone. Two or more inputs often share the same zone.


QQUUIICCKK RREEFFEERREENNCCEE GGUUIIDDEETo arm using your remote➤ You can activate, or arm, the system by pressing on your transmitter for one

second. When the system arms, you will hear a short siren sound, or chirp, andthe parking lights will flash once. If the vehicle’s power door locks have beenconnected to the system, the doors will lock.

To disarm using your remote➤ To disarm the system, press . You will hear two chirps, and the parking

lights will flash twice. If power locks are connected to the system, the doors willunlock. If the siren chirps either four or five times when disarming, seeDiagnostics section. This is called Tamper Alert.

Disarming without a transmitter➤ Turn on the ignition. Press the Valet button the programmed number of times

within 15 seconds. After five seconds, the system will disarm. If it does not, youmay have waited too long. Turn the ignition off and on and try again.

To enter or exit Valet Mode➤ Turn ignition to RUN position, then turn to OFF position. Press and release

the Valet button within 10 seconds. The status LED will light solid if you areentering Valet Mode, and it will go out if you are exiting Valet Mode.

To activate Panic Mode➤ Press and hold down for two seconds.

To exit Panic Mode➤ Press on the transmitter.

To activate Silent Mode™➤ Press briefly before arming or disarming, and the confirmation chirp(s)

will be eliminated for that one operation only.

Location of Valet Button_______________________________

Number of Valet Button pulses for disarming_____________

Cut

alon

g do

tted

line

and

fol

d fo

r a

quic

k an

d ea

sy r

efer

ence

to

keep

in

your

pur

se o

r w

alle

t.✂✂

✂✂

Directed ElectronicsVista, CA 92081

www.directed.com© 2006 Directed Electronics - All rights reserved

G3102V 11-06

The company behind this system is Directed Electronics

Since its inception, Directed has had one purpose, to provide consumers with thefinest vehicle security and car stereo products and accessories available. The recipientof more than 20 patents in the field of advanced electronic technology, Directed isISO 9001 registered.

Quality Directed Electronics products are sold and serviced throughout North Americaand around the world.

Call (800) 274-0200 for more information about our products and services.

Directed® is committed to delivering world class quality products

and services that excite and delight our customers.

1002 model - directeddealers.com · 1002 model owner’s guide ... and the unit is returned to...

Documents