10 parameter optimisation hw

67
Huawei Confidential. All Rights Reserved Parameters Optimization ISSUE 1.0

Upload: agung-pur

Post on 15-Feb-2016

19 views

Category:

Documents


0 download

DESCRIPTION

optimization for Huawei parameters

TRANSCRIPT

Page 1: 10 Parameter Optimisation HW

Huawei Confidential. All Rights Reserved

Parameters Optimization

ISSUE 1.0

Page 2: 10 Parameter Optimisation HW

2 Internal Use

Review Review

Parameters Optimization is an important step after RF Optimization

Service quality and network resources utilization will be improved after Parameters Optimization

Page 3: 10 Parameter Optimisation HW

3 Internal Use

ReviewReview

New Sites Intergrated

Single Site Verification

Cluster of Sites ready?

RF Optimisation

Services Testing & Parameter Optimisation

Regular Reference RouteTesting & Stats Analysis

Re- optimisation Needed?

YES

NO

YES

NO

Page 4: 10 Parameter Optimisation HW

4 Internal Use

ObjectivesObjectives

Upon completion this course, you will be able to:

Understand the procedure of Parameters Optimization

Master the contents of Parameters Optimization.

Page 5: 10 Parameter Optimisation HW

5 Internal Use

Chapter 1 Chapter 1 Parameters Optimization Parameters Optimization ProcedureProcedureChapter 2 Chapter 2 Parameters Optimization Parameters Optimization ContentContent

Page 6: 10 Parameter Optimisation HW

6 Internal Use

Parameters Optimization ProcedureParameters Optimization Procedure

Data Input and Find Problems

Verify Parameter Problems

Other ProcessClassify Parameter Problems

Determine Parameter Values to be Modified and List MML Commands

Evaluate Changing Effects

Prepare Test Plan and Implement Changing

Test , Get Data again and Compare

Problems Eliminate Or Need not Change more

End

Determine whether Changing

End

N

N

Y

Y

Y

N

Page 7: 10 Parameter Optimisation HW

7 Internal Use

Data Input and Find ProblemsData Input and Find Problems

Data Input

Drive Test Data

KPI Network Statistic Data

Network Tracing Message

Network Warning Information

Problems

Use Input Data to find out the Problems such as - Call Setup Success Rate Low - Handover Success Rate Low - Drop Call Rate High etc.

Page 8: 10 Parameter Optimisation HW

8 Internal Use

Verify Parameter ProblemsVerify Parameter Problems

Parameter Problems

No RF Problems

No Hardware/Software Problem

Related with EnvironmentOr Speed

Parameters never OptimizedBefore

Page 9: 10 Parameter Optimisation HW

9 Internal Use

Classify Parameter ProblemsClassify Parameter Problems

Mobile Management Parameter Problems Power Control Parameter Problems Power Configuration Parameter Problems Load Control Parameter Problems Other Parameter Problems

Page 10: 10 Parameter Optimisation HW

10 Internal Use

Determine Parameter ValuesDetermine Parameter Values

List Parameters Changing Form Original Parameter Values vs. New Parameter Values List Parameters Changing MML Command

Page 11: 10 Parameter Optimisation HW

11 Internal Use

Evaluate Changing InfluenceEvaluate Changing Influence

Evaluate influence on Customer Service and Other Networks

Evaluate influence on OMC ( Efforts , Maintenance)

Page 12: 10 Parameter Optimisation HW

12 Internal Use

Prepare Test Plan and Implement ChangingPrepare Test Plan and Implement Changing

Prepare Test schedule , Routes, Tools and be ready to get Information .

Change Parameters and Make Records.

Page 13: 10 Parameter Optimisation HW

13 Internal Use

Chapter 1 Chapter 1 Parameters Optimization Parameters Optimization ProcedureProcedureChapter 2 Chapter 2 Parameters Optimization Parameters Optimization ContentContent

Page 14: 10 Parameter Optimisation HW

14 Internal Use

Chapter 2 Parameter Optimization ContentsChapter 2 Parameter Optimization Contents

1. Cell Selection & Reselection

2. Handover

Page 15: 10 Parameter Optimisation HW

15 Internal Use

Parameters Optimization ContentsParameters Optimization Contents

Mobile Management Parameters Optimization Power Control Parameters Optimization Power Configuration Parameters Optimization Load Control Parameters Optimization

Note: Because there are a lot of parameters , it is not possible to introduceevery parameter . Only some parameters about network optimization are mentioned here and maybe more parameters need to be added in the future.

Page 16: 10 Parameter Optimisation HW

16 Internal Use

Mobile Management Parameters OptimizationMobile Management Parameters Optimization

Cell Selection & Reselection Cell Selection & Reselection - Only for UE in Idle more or Cell_FACH, CELL_PCH and URA_PCH

- Changing of cell on which UE camped on, - To ensure UE is always connected to the best serving cell to receive system information and establishing RRC connection

HandoverHandover - Changing cell for UE in CELL_DCH mode

- Ensure seamless coverage and load balancing.

Page 17: 10 Parameter Optimisation HW

17 Internal Use

Cell Selection & Reselection ProcedureCell Selection & Reselection Procedure

InitialCell Selection

Any CellSelection

go herewhen noUSIM inthe UE

USIM inserted

Camped onany cell

go here whenever anew PLMN is

selected

1no cell information

stored for the PLMNcell information

stored for the PLMN

Storedinformation

Cell Selectionno suitable cell found

no suitablecell found

Cell Selectionwhen leaving

connectedmode

suitable cell found 2

suitablecell found

Campednormally

suitable cell found

no suitablecell found

leaveidle mode

return toidle mode

Connectedmode

CellReselectionEvaluationProcess

suitablecell found

trigger

no suitablecell found

1

Cell Selectionwhen leaving

connectedmode

no acceptable cell found

acceptablecell found

acceptablecell found

suitablecell found 2

leaveidle mode

return toidle mode

Connectedmode

(Emergencycalls only)

CellReselectionEvaluationProcess

acceptablecell found

trigger

no acceptablecell found

NAS indicates thatregistration on selected

PLMN is rejected(except with cause #14

or #15 [5][16])

Page 18: 10 Parameter Optimisation HW

18 Internal Use

Cell Selection Criteria (S Criteria)Cell Selection Criteria (S Criteria)

The cell selection criterion S is fulfilled when:The cell selection criterion S is fulfilled when:

for FDD cells: Srxlev > 0 AND Squal > 0

for TDD cells: Srxlev > 0

Where:

Squal = Qqualmeas – Qqualmin

Srxlev = Qrxlevmeas - Qrxlevmin - Pcompensation

When UE wants to select an UMTS cell , the cell should satisfy S Criterion.

Page 19: 10 Parameter Optimisation HW

19 Internal Use

Cell Selection ParametersCell Selection Parameters

Page 20: 10 Parameter Optimisation HW

20 Internal Use

Cell Re-selection Measure ConditionCell Re-selection Measure Condition

Uses Squal for FDD cells and Srxlev for TDD for Sx

Sx > SintrasearchSx > Sintrasearch, UE need not perform intra-frequency measurements.

Sx <= SintrasearchSx <= Sintrasearch, perform intra-frequency measurements.If Sintrasearch is not sent for serving cell, perform intra-frequency measurements.

Sx > SintersearchSx > Sintersearch, UE need not perform inter-frequency measurements.

Sx <= SintersearchSx <= Sintersearch, perform inter-frequency measurements.If Sintersearch, is not sent for serving cell, perform inter-frequency measurements.

Sx > SsearchRAT mSx > SsearchRAT m, UE need not perform measurements on cells of RAT"m".

If Sx <= SsearchRAT mIf Sx <= SsearchRAT m, perform measurements on cells of RAT "m".If SsearchRAT m, is not sent for serving cell, perform measurements on cells of RAT "m".

Page 21: 10 Parameter Optimisation HW

21 Internal Use

Cell Reselection Criteria (R Criteria)Cell Reselection Criteria (R Criteria)

1) All cells satisfy S Criteria. 2) Select the Cell with the highest R value using the following method:

Cells are ranked according to the R criteria.R values are calculated using CPICH RSCP, P-CCPCH RSCP and the averaged received signal level for FDD, TDD and GSM cells, respectively.In all cases, the UE shall reselect the new cell, only if the following conditions are met:

- New cell is better ranked than the serving cell during a time interval Treselection.- More than 1 second has elapsed since UE camped on the current serving cell.

RRss = Q= Qmeas,smeas,s + Q+ Qhyst, shyst, s

RRnn = Q= Qmeas,nmeas,n - Q- Qoffset, s,noffset, s,n

Page 22: 10 Parameter Optimisation HW

22 Internal Use

Cell Reselection ParametersCell Reselection Parameters

Page 23: 10 Parameter Optimisation HW

23 Internal Use

Cell Reselection ParametersCell Reselection Parameters

Page 24: 10 Parameter Optimisation HW

24 Internal Use

Chapter 2 Parameter Optimization ContentsChapter 2 Parameter Optimization Contents

1. Cell Selection & Reselection

2. Handover

Page 25: 10 Parameter Optimisation HW

25 Internal Use

Handover ProcedureHandover Procedure

Node B

Node B

Node B

Intra-frequency cells

–Neighbor cells both from same NodeB or other NodeBs

Measurement report

Handover decision

measurement control

Measurement and filtering

Handover execution

Page 26: 10 Parameter Optimisation HW

26 Internal Use

Soft Handover ExampleSoft Handover Example

Page 27: 10 Parameter Optimisation HW

27 Internal Use

Soft Handover ProcedureSoft Handover Procedure

Page 28: 10 Parameter Optimisation HW

28 Internal Use

Soft Handover Event – 1ASoft Handover Event – 1A

1A (Add a cell in Active Set)1A (Add a cell in Active Set)

)2/(10)1(1010 111

aaBest

N

iiNewNew HRLogMWMLogWCIOLogM

A

MNew : Measurement result of cell entering the reporting range.CIONew : Cell individual offset for the cell entering the reporting range if an individual cell offset is stored for that cell. Otherwise it is equal to 0.Mi : Measurement result of a cell not forbidden to affect reporting range in the active set.NA : The number of cells not forbidden to affect reporting range in the current active set.MBest : Measurement result of the cell not forbidden to affect reporting range in the active set with the highest measurement result, not taking into account any cell individual offset.W : Parameter sent from UTRAN to UE.R1a : Reporting range constant.H1a : Hysteresis for the event 1a.

Page 29: 10 Parameter Optimisation HW

29 Internal Use

Soft Handover Event – 1BSoft Handover Event – 1B

1B (Remove a cell from Active Set)1B (Remove a cell from Active Set)

)2/(10)1(1010 111

bbBest

N

iiOldOld HRLogMWMLogWCIOLogM

A

MOld : Measurement result of the cell leaving the reporting range.CIOOld : Cell individual offset for the cell leaving the reporting range if an individual cell offset is stored for that cell. Otherwise it is equal to 0.Mi : Measurement result of a cell not forbidden to affect reporting range in the active set.NA : Number of cells not forbidden to affect reporting range in the current active set.MBest : Measurement result of the cell not forbidden to affect reporting range in the active set with the lowest measurement result, not taking into account any cell individual offset. W : Parameter sent from UTRAN to UE.R1b : Reporting range constant.H1b : Hysteresis for the event 1b.

Page 30: 10 Parameter Optimisation HW

30 Internal Use

Soft Handover Event – 1CSoft Handover Event – 1C

1C (A non-active primary CPICH becomes better than an active primary CPICH. If Active Set is not full ,add the non-active cell into active set .Otherwise use the cell substitute the active cell . )

2/1010 1cInASInASNewNew HCIOLogMCIOLogM

MNew : Measurement result of the cell not included in the active set.CIONew : Cell individual offset for the cell becoming better than the cell in the active set if an individual cell offset is stored for that cell. Otherwise it is equal to 0.MInAS : Measurement result of the cell in the active set with the highest measurement result.MInAS : Measurement result of the cell in the active set with the lowest measurement result.CIOInAS : Cell individual offset for the cell in the active set that is becoming worse than the new cell.H1c : Hysteresis parameter for the event 1c.

Page 31: 10 Parameter Optimisation HW

31 Internal Use

Soft Handover Event – 1DSoft Handover Event – 1D

1D (Change of best cell. If the chosen cell is not in Active Set , add the cell into Active Set and modify measurement control .Otherwise only modify measurement control. )

2/1010 1dBestBestNotBestNotBest HCIOLogMCIOLogM

MNotBest : Measurement result of a cell not stored in "best cell" CIONotBest : Cell individual offset of a cell not stored in "best cell" .MBest: Measurement result of the cell stored in "best cell".CIOBest : Cell individual offset of a cell stored in "best cell" .H1d : Hysteresis parameter for the event 1d.

Page 32: 10 Parameter Optimisation HW

32 Internal Use

Soft Handover ParametersSoft Handover Parameters

Parameter NameParameter Name DescriptionDescription Default SettingDefault Setting

IntraRelThdFor1A Relative thresholds of soft handover for Event 1A (R1a) 10 , namely 5dB (step 0.5)

IntraRelThdFor1B Relative thresholds of soft handover for Event 1B (R1b) 10 , namely 5dB (step 0.5)

Hystfor1A, Hystfor1B, Hystfor1C, Hystfor1D

Soft handover hysteresis (H1x) 6,namely 3dB (step 0.5) for H1a .8,namely 4dB(step 0.5) for H1b, H1c,H1d.

CellIndividalOffset Cell CPICH measured value offset; the sum of this parameter value and the actually tested value is used for UE event estimation. (CIO)

0

WEIGHT Weighting factor, used to determine the relative threshold of soft handover according to the measured value of each cell in the active set.

0

TrigTime1A,TrigTime1B, TrigTime1C,TrigTime1D

Soft handover time-to-trigger parameters (event time-to-trigger parameters. Only the equation are always satisfied during the trigger time, the event will be triggered).

D640, namely 640ms .

FilterCoef Filter coefficient of L3 intra-frequency measurement D5 ,namely 5

Page 33: 10 Parameter Optimisation HW

33 Internal Use

Intersystem Handover – CS Domain ProcedureIntersystem Handover – CS Domain ProcedureUE

1. RRC Connect Req

15. RAB Assign Req

NODEB RNC 3G MSC BSS2G MSC

2. RRC Setup Complete

3. Measure Control (measure ID 0x1 ) 4. Measure Control (measure ID 0x2 )

5.Initial UE message(service request)6.DL DT (Authentication Request)7.UL DT (Authentication Response)

8.Common ID

9. Security Mode Command10. Security Mode Command11. Security Mode CMP

12. Security Mode CMP13. UL DT(Setup)14. DL DT(Call proceeding)

17.RL Recfg Ready

21 RAB Assign Resp20 RB Setup Cmp19 RB Setup

16.RL Recfg Prep

18.RL Recfg Commit

22. DL DT( Alerting )23. DL DT( Connect)24. UL DT(Connect Ack)

26.RL Recfg Prep26.RL Recfg Prep

28 PhyCh Reconfig28 PhyCh Reconfig29.RL Recfg Comit29.RL Recfg Comit

27.RL Recfg Ready27.RL Recfg Ready

30 PhyCh Reconfig CMP30 PhyCh Reconfig CMP31 Meaure Control(ID3 )

32Measure Report 33 Relocation Required34 Relocation Command

35. HandoverFromUtranCommand44 Iu Release Req

46 RL Del Resp45 RL Del Req

47 Iu Release Complete

25 Measure Report(2D)

Page 34: 10 Parameter Optimisation HW

34 Internal Use

Intersystem Handover MeasureIntersystem Handover Measure

1)1) Inter-frequency measurement reporting Event 2D ,2FInter-frequency measurement reporting Event 2D ,2F

to reflect the currently used frequency quality.

Event 2d:Event 2d: The estimated quality of the currently used frequency is below a certain threshold.

The variables in the formula are defined as follows:

QUsed : Quality estimate of the used frequency. TUsed 2d : The absolute threshold that applies for the used frequency and event 2d. H2d : Hysteresis parameter for the event 2d.

Event 2fEvent 2f: The estimated quality of the currently used frequency is above a certain threshold.

The variables in the formula are defined as follows:

QUsed : The quality estimate of the used frequency. TUsed 2f : The absolute threshold that applies for the used frequency and event 2f. H2f : Hysteresis parameter for the event 2f.

2/22 ddUsedUsed HTQ

2/22 ffUsedUsed HTQ

Page 35: 10 Parameter Optimisation HW

35 Internal Use

Intersystem Handover MeasureIntersystem Handover Measure 2) RNC Receive 2D reportsRNC Receive 2D reports ( i.e current serving carrier signal is poor ) :

- RNC sends Measurement Control (ID3); Allow UE to begin measure other system signal. - UE will send measurement result reports periodically

- When Received 2F reports ( i.e current serving carrier signal is no longer poor), RNC sends Measurement Control (ID3, but different contents) to let UE stop measuring other system signal .

3) When RNC received periodical reports ,RNC use the following formula to judge whether it should handover UE to another system .

MMother_RAT other_RAT + CIO > T+ CIO > Tother_RATother_RAT + H/2 + H/2

Tother_RAT : Inter-system handover decision threshold

Mother_RAT : Inter-system (GSM RSSI) measurement result received by RNC

CIO : Cell Individual Offset, which is the inter-system cell setting offset; H : Hysteresis,

If the formula is met, a trigger-timer called TimeToTrigForSysHo will be started, and a handover decision will be made when the timer expires;

Note: If inter-system quality satisfies the following condition before the timer expires: Mother_RAT + CIO < Tother_RAT - H/2Mother_RAT + CIO < Tother_RAT - H/2 timer will stopped, and RNC will waiting to receive the next inter-system measurement report.

Page 36: 10 Parameter Optimisation HW

36 Internal Use

Intersystem Handover ParametersIntersystem Handover Parameters

Page 37: 10 Parameter Optimisation HW

37 Internal Use

Parameters Optimization ContentsParameters Optimization Contents

Mobile Management Parameters Optimization Power Control Parameters Optimization Power Configuration Parameters Optimization Load Control Parameters Optimization

Page 38: 10 Parameter Optimisation HW

38 Internal Use

Power Control Parameters OptimizationPower Control Parameters Optimization

Power Control Characteristics

Minimize the interferenceMinimize the interference in the network, thus improve capacity and quality

Maintain link qualityMaintain link quality in uplink and downlink by adjusting the powers

Overcome near far effectOvercome near far effect by providing minimum required power level for each connection

Provides protection against shadowing and fast fadingprotection against shadowing and fast fading

Page 39: 10 Parameter Optimisation HW

39 Internal Use

Power Control ClassificationPower Control Classification

UE NodeB RNC

SIR Target

Bler/BerSIR

TPC Command

Outer Loop Power ControlInner Loop Power Control

Open Loop Power Control

Open Loop Power ControlOpen Loop Power Control To determine UE’s initial uplink transmit power in PRACH and NodeB’s initial downlink transmit power in DPDCH.

Outer Loop power controlOuter Loop power control To maintain the quality of communication at the level of bearer service quality requirement, while using power as low as possible.

Inner loop power control (also called fast closed loop power controlInner loop power control (also called fast closed loop power control To adjust UE’s uplink / NodeB’s downlink DPCH. Power of every one slot in accordance with TPC commands. Inner loop power control frequency is 1500Hz

Page 40: 10 Parameter Optimisation HW

40 Internal Use

Open Loop Power Control - UplinkOpen Loop Power Control - Uplink

BCH£ ºCPICH channel powerBCH£ ºCPICH channel power UL interference leve UL interference leve Constant Value Constant Value

Measure CPICH_RSCP Measure CPICH_RSCP and determine the initial and determine the initial transmitted power transmitted power

RACHRACH

Preamble_Initial_Power = Primary CPICH TX power - CPICH_RSCP Preamble_Initial_Power = Primary CPICH TX power - CPICH_RSCP + UL interference + Constant Value+ UL interference + Constant Value

Primary CPICH TX power , UL interference and Constant Value are broadcasted in the System Informationand CPICH_RSCP is the measured value by UE 。

Page 41: 10 Parameter Optimisation HW

41 Internal Use

Open Loop Power Control - DownlinkOpen Loop Power Control - Downlink

DCHDCH

Measure CPICH Ec/I0Measure CPICH Ec/I0

RACH reports the RACH reports the measured valuemeasured value

Determine the downlink initial power Determine the downlink initial power controlcontrol

RR : User bit rate. W W : Chip rate (3.84M).PcpichPcpich : Primary CPICH transmit power. Eb/IoEb/Io : Downlink Eb/Io required value for a bearer service.(Ec/Io)cpich(Ec/Io)cpich : Measurement value reported by the UE. : Downlink cell orthogonal factor.Ptotal Ptotal : Current cell’s carrier transmit power measured at the NodeB and reported to the RNC.

))/(( totalo

cCPICH

o

b PcpichIEP

WR

IEP

Page 42: 10 Parameter Optimisation HW

42 Internal Use

Open Loop Power Control ParametersOpen Loop Power Control Parameters

Page 43: 10 Parameter Optimisation HW

43 Internal Use

Outer Loop Power ControlOuter Loop Power Control

SRNC DRNC

Set SI R Set SI R targettarget

Set SI R targetSet SI R target

Set SI R targetSet SI R target

Macro di versi ty Macro di versi ty combi ni ngcombi ni ng

Used to setting SIRTarget for inner loop power control.

Uplink outer loop power control is controlled by SRNC (serving RNC) for setting a target SIR for each UE. SIRTarget is updated according to the estimated uplink quality (Block Error Ratio/ Bit Error Ratio). If UE is not in DTX status (that means RNC can receive uplink traffic data), RNC uses BLER to compute SIRTarget . Otherwise , RNC will use BER to compute SIRTarget.

Downlink outer loop power control controlled by UE receiver; to converge to required link quality (BLER) set by the network (RNC) in downlink.

Page 44: 10 Parameter Optimisation HW

44 Internal Use

Outer Loop Power Control ParametersOuter Loop Power Control Parameters

Page 45: 10 Parameter Optimisation HW

45 Internal Use

Inner Loop Power ControlInner Loop Power Control

Divided into uplink and downlink inner-loop power control

Purpose to adjusts UE or NodeB transmit power, to keep the received SIR to be around SIR target.

Page 46: 10 Parameter Optimisation HW

46 Internal Use

Uplink Inner Loop Power ControlUplink Inner Loop Power Control

UTRAN behaviourUTRAN behaviour Serving cells (cells in the active set) estimate SIRest of the received uplink DPCH. Serving cells then generate TPC commands and transmit TPC on every slot according to the fo

llowing rule: if SIRest > SIRtarget , TPC = "0", if SIRest < SIRtarget , TPC = "1".

UE behaviourUE behaviour Upon reception of one or more TPC commands in a slot, UE shall derive a single TPC comman

d, TPC_cmd, for each slot, combining multiple TPC commands if more than one is received in a slot. This is also valid when SSDT transmission is used in the downlink.

Two algorithms supported by UE when deriving a TPC_cmd. Which algorithms to be used is determined by a UE-specific higher-layer parameter, "PowerCo

ntrolAlgorithm", and is under the control of the UTRAN. If "PowerControlAlgorithm" indicates "algorithm1", then the layer 1 parameter PCA shall take th

e value 1 and if "PowerControlAlgorithm" indicates "algorithm2" then PCA shall take the value 2.

Page 47: 10 Parameter Optimisation HW

47 Internal Use

Uplink Inner Loop Power ControlUplink Inner Loop Power Control

The step size DTPC is a layer 1 parameter which is derived from the UE-specific higher-layer parameter "TPC-StepSize" which is under the control of the UTRAN.

If "TPC-StepSize" has the value "dB1", then the layer 1 parameter DTPC shall take the value 1 dB and if "TPC-StepSize" has the value "dB2", then DTPC shall take the value 2 dB.

The parameter "TPC-StepSize" only applies to Algorithm 1 . For Algorithm 2 DTPC shall always take the value 1 dB.

After deriving of the combined TPC command TPC_cmd using one of the two supported algorithms, UE shall adjust the transmit power of uplink DPCCH with a step of DDPCCH (in dB) which is given by:

DDPCCH = DTPC TPC_cmd.

Page 48: 10 Parameter Optimisation HW

48 Internal Use

Uplink Inner Loop Power ControlUplink Inner Loop Power Control

Algorithm 1Algorithm 1

UE received 0ne TPC in not soft handover. The value of TPC_cmd is derived as follows:

-- If TPC = 0 ; then TPC_cmd = –1.If TPC = 0 ; then TPC_cmd = –1.

-- If TPC = 1 ; then TPC_cmd = 1 If TPC = 1 ; then TPC_cmd = 1

Algorithm 2Algorithm 2

UE not in soft handover, only one TPC received. In this case, UE shall process re

ceived TPC on a 5-slot cycle.

TPC_cmd value shall be derived as follows:

The first 4 slots of a set, TPC_cmd = 0 . No change in power

The 5th slot of a set, TPC _cmd is derived as follows:

If all TPC are 0; TPC_cmd = -1If all TPC are 0; TPC_cmd = -1 and the transmission will decrease 1dB;

If all TPC are 1; TPC_cmd = 1If all TPC are 1; TPC_cmd = 1 and the transmission will increase 1dB;

Otherwise, TPC_cmd=0Otherwise, TPC_cmd=0.

Page 49: 10 Parameter Optimisation HW

49 Internal Use

Downlink Inner Loop Power ControlDownlink Inner Loop Power Control

UE behaviourUE behaviour UE generate TPC commands to control the network transmit power and send them in t

he TPC field of the uplink DPCCH. The UE shall check the downlink power control mode (DPC_MODE) before generating

the TPC command:

If DPC_MODE = 0DPC_MODE = 0 : UE sends a unique TPC command in each slot and the TPC command generated is transmitted in the first available TPC field in the uplink DPCCH;

If DPC_MODE = 1DPC_MODE = 1 : UE repeats the same TPC command over 3 slots and the new TPC command is transmitted such that there is a new command at the beginning of the frame.

The DPC_MODEDPC_MODE parameter is a UE specific parameter controlled by the UTRAN.

Page 50: 10 Parameter Optimisation HW

50 Internal Use

Downlink Inner Loop Power ControlDownlink Inner Loop Power Control

UTRAN behaviourUTRAN behaviour Upon receiving the TPC commands, UTRAN adjust its downlink DPCCH/DPDCH

power accordingly.

For DPC_MODE = 0DPC_MODE = 0, UTRAN estimate the transmitted TPC command TPCest to be 0 or 1, and shall update the power every slot.

If DPC_MODE = 1DPC_MODE = 1, UTRAN estimate the transmitted TPC command TPCest over three slots to be 0 or 1, and shall update the power every three slots.

Page 51: 10 Parameter Optimisation HW

51 Internal Use

Inner Loop Power Control ParametersInner Loop Power Control Parameters

Page 52: 10 Parameter Optimisation HW

52 Internal Use

Parameters Optimization ContentsParameters Optimization Contents

Mobile Management Parameters Optimization Power Control Parameters Optimization Power Configuration Parameters Optimization Load Control Parameters Optimization

Page 53: 10 Parameter Optimisation HW

53 Internal Use

Physical Channels TypePhysical Channels Type

Page 54: 10 Parameter Optimisation HW

54 Internal Use

Common Channels ParametersCommon Channels Parameters

All channels’ power is reference to PCPICH Power expect PCPICH itself .

Page 55: 10 Parameter Optimisation HW

55 Internal Use

Dedicated Channels ParametersDedicated Channels Parameters

Dedicated Channel Power is also reference to PCPICH Power.

Page 56: 10 Parameter Optimisation HW

56 Internal Use

Parameters Optimization ContentsParameters Optimization Contents

Mobile Management Parameters Optimization Power Control Parameters Optimization Power Configuration Parameters Optimization Load Control Parameters Optimization

Page 57: 10 Parameter Optimisation HW

57 Internal Use

Load Control Parameters OptimizationLoad Control Parameters Optimization

Call Admission Control (CAC)

To control cell’s load by admission/rejection request to ensure a cell’s load under control.

Dynamic Channel Configuration Control (DCCC)

To dynamically change a connection’s load to improve cell resource utilization and control cell’s load.

Page 58: 10 Parameter Optimisation HW

58 Internal Use

Call Admission Control Procedure Call Admission Control Procedure

call admisson request arrive

Get the service characteristic and the current load

Uplink call admission control evaluation

admitted?

Downlink call admission control evaluation

admitted?

call admitted call rejected

end

n

y

y

n

Page 59: 10 Parameter Optimisation HW

59 Internal Use

Call Admission Control ParametersCall Admission Control Parameters

Page 60: 10 Parameter Optimisation HW

60 Internal Use

Dynamic Channel Configuration ControlDynamic Channel Configuration Control

DCCC: Dynamic Channel Configuration Control aim to making full use of radio resource (codes, power, CE )

- Configured bandwidth is fixed when no DCCC- Configured bandwidth is changing when DCCC- Traffic rate

Rate or band

Page 61: 10 Parameter Optimisation HW

61 Internal Use

DCCC ProcedureDCCC Procedure

Measurement report

DCCC decision

Traffic Volume measurement control

UE and RNC Measurement

DCCC execution

Page 62: 10 Parameter Optimisation HW

62 Internal Use

Traffic Volume MeasurementTraffic Volume Measurement

Threshold

Transport Channel Traffic Volume

Reporting event 4A

Time

Reporting event 4A

Threshold

Transport Channel Traffic Volume

Reporting event 4B

Time

Reporting event 4B

Reporting event 4B

Page 63: 10 Parameter Optimisation HW

63 Internal Use

DCCC DecisionDCCC Decision

1) 4a event report -> increase bandwidth 4b event report -> decrease bandwidth

2) If current bandwidth<=DCCC threshold, don’t decrease bandwidth

Page 64: 10 Parameter Optimisation HW

64 Internal Use

Dynamic Channel Configuration Control Dynamic Channel Configuration Control ParametersParameters

Page 65: 10 Parameter Optimisation HW

65 Internal Use

Dynamic Channel Configuration Control Dynamic Channel Configuration Control ParametersParameters

Page 66: 10 Parameter Optimisation HW

66 Internal Use

SummarySummary

Parameter Optimization improves network quality and solves network problems.

Parameter Optimization is a complicated procedure and needs parameter and algorithm knowledge.

Parameter Optimization will be combined with other optimization activities making network better !

Page 67: 10 Parameter Optimisation HW

Huawei Confidential. All Rights Reserved